Professional Documents
Culture Documents
1. Do not use the browser Back button or close or reload any exam windows during the exam. 2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work.
Introduction
In this Packet Tracer Practice Skills Based Assessment, you will do the following: finish designing the IP addressing scheme implement the addressing in the network to meet the requirements configure Frame Relay and EIGRP to enable communication with the rest of the network configure a backup link in case the Frame Relay network becomes unavailable implement a security policy by using access control lists to filter traffic
Addressing Table
Device Interface Fa0/0.1 Fa0/0.15 Branch Fa0/0.25 Fa0/1 S0/0/0.55 Address 10.10.10.177 10.10.10.129 10.10.10.161 172.16.1.2 10.255.1.1 Subnet Mask 255.255.255.248 255.255.255.224 255.255.255.240 255.255.255.252 255.255.255.252 Default Gateway n/a n/a n/a n/a n/a
Fa0/0 HQ Fa0/1 S0/0/0.65 Internet BR-S1 BR-S2 HQ-S1 PC1 Admin Web Server Fa0/0 Fa0/1 VLAN1 VLAN1 VLAN1 NIC NIC NIC
10.10.20.1 172.16.1.6 10.255.1.2 172.16.1.1 172.16.1.5 10.10.10.178 10.10.10.179 10.10.20.2 10.10.10.174 10.10.10.158 10.10.20.6
255.255.255.248 255.255.255.240
10.10.20.1 10.10.10.161
255.255.255.248
10.10.20.1
NOTE: To aid in configuring, verifying and troubleshooting the devices, use a printed version of these instructions to fill in the missing address information in the table during Step 1.
k. Assign the second address in this subnet to the VLAN 1 interface on BR-S1.
Step 3: Configure BR-S1 with IP Address, VLANs and as the STP Root Bridge.
NOTE: BR-S2 is already configured. You do not have access to BR-S2. On BR-S1, you will receive a Domain Mismatch message every 30 seconds until BR-S1 is correctly configured. a. Configure the BR-S1 VLAN 1 interface with the correct IP addressing as determined in Step 1 b. Configure the default gateway. c. Establish an 802.1q trunk with Branch and with BR-S2. After STP converges, BR-S1 should be able to ping both Branch and BR-S2.
switch BR-S1 Int vlan 1 Ip add 10.10.10.178 255.255.255.248 No shut Ip default-gateway 10.10.10.177 Conf t Int fa 0/1 Switchport mode access Switchport mode trunk Exit Int fa 0/2 Switchport mode access Switchport mode trunk exit d. BR-S1 should be configured as a VTP server for the branch domain. Set the VTP password tovtpbranch. BR-S2 is already configured as a client for this domain. switch BR-S1 Conf t Vtp domain branch Vtp password vtpbranch Vtp mode server e. Create and name two VLANs on the VTP server. Names are case-sensitive: VLAN 15, Name: Administration switch BR-S1 Vlan 15 Name Administration exit VLAN 25, Name: Employee Vlan 25 Name Employee Exit
f. Assign VLAN 15 to the Fa0/10 interface for Admin access. switch BR-S1 Conf t Int fa0/10
Switchport mode access Switchport access vlan 15 exit g. Use a priority of 8192 to set BR-S1 as the STP root for all VLANs. switch BR-S1 Conf t Spanning-tree vlan 1 priority 8192 Spanning-tree vlan 15 priority 8192 Spanning-tree vlan 25 priority 8192 Exit
router Branch Conf t interface serial 0/0/0 encapsulation frame-relay no shutdown exit interface serial 0/0/0.55 point-to-point ip address 10.255.1.1 255.255.255.252 frame-relay interface-dlci 55 b. Verify that Frame Relay is operational between Branch and HQ. c. Branch should be able to ping the directly-connected interface of HQ.
b. Verify that Branch is now a neighbor with HQ. c. Admin should be able to ping the Web Server. d. Use the Add Simple PDU tool to verify that PC1 can ping the Web Server.
router Branch
Int fa0/0 ip summary-address eigrp 50 10.10.10.128 255.255.255.192 150 exit Int fa0/1 ip summary-address eigrp 50 10.10.10.128 255.255.255.192 150 exit Int s0/0/0 ip summary-address eigrp 50 10.10.10.128 255.255.255.192 150 exit