You are on page 1of 4

Main menu

Submenu

Submenu Error Diffusion

Clock Dithering

On Off

Pick and Kick

(none)

To gain access to the developers menu


1. 2. 3. Make sure that Ready appears on the control-panel display. Press Menu. Press the * and # buttons simultaneously. NOTE You can gain access to the developers menu from any other menu by pressing the * and # buttons simultaneously. 4. 5. Use the < or > button to navigate through the developers menu. To exit the developers menu and remove it from the menu tree, press Cancel to return to the Ready display, and then press Cancel again.

To adjust fax data-store parameters


When you adjust fax data-store parameters, the product does not alert you to incorrect input values. Changing fax data-store parameters can render the product illegal or inoperable. NOTE Before adjusting the fax data-store parameters, print a list of all of the parameters from the secondary service menu. See To print a list of all the fax data-store parameters on page 251. 1. 2. 3. On the developers menu, use the < or > button to navigate to Dev. Reports, and then press Use the < or > button to navigate to DS Fax and select the parameter that you want to change. The current setting appears on the control-panel display. Type the new value for the fax data-store parameter, and then press . .

To scroll quickly to a particular data-store parameter


When DS Fax appears on the control-panel display, jump directly to any parameter ID that does not contain a 2 by typing the ID on the keypad. (Pressing 2 brings up the secondary service menu.) To change a parameter that has a 2 in its ID, type the ID of the closest parameter that does not have a 2 and then use the < or > button to locate the parameter that you want to change. For example, to move quickly to parameter 152, type 151 >.

ENWW

Service-mode functions

253

Changing the country/region code parameters


Three situations can occur that necessitate changing the country/region or language settings for the product: 1. 2. 3. The customer has moved to a different country/region from the country/region in which the all-inone was purchased. The information has been erased because of an NVRAM initialization, or the parameters are set to "undefined." The formatter has been replaced.

Use the information in the following sections to change the country/region and language settings.

To change the country/region from one location to another


1. 2. 3. 4. Press Menu and then press 2 to gain access to the Secondary Service menu. Press < or > to select Location, and then press Press < or > until the correct location appears. When the correct location appears, press . Press 1 to confirm the new location. The all-in-one automatically turns itself off and then on after the setting is confirmed. .

To set the language and location if none is set


If the language and location have been erased because the NVRAM has been initialized or the formatter has been replaced, the product automatically prompts for the language and the location when it is turned on. NOTE HP LaserJet 3050 all-in-one and HP LaserJet 3055 all-in-one: The customer cannot send or receive faxes until these settings have been established. 1. 2. 3. Press < or > until the correct language appears. When the correct language appears, press and then press 1 to confirm the selection. If the location also needs to be set, the product automatically prompts for the location. Press < or > until the correct country/region appears. NOTE HP LaserJet 3050 all-in-one and HP LaserJet 3055 all-in-one: The list of countries/regions that appears on the control-panel display depends on the LIU that is installed in the product. HP LaserJet 3052 all-in-one: This product does not have fax capabilities and so it does not have an LIU installed. The list of supported countries/regions that appears on the controlpanel display is in a localized format. 4. 5. When the correct country/region appears, press and then press 1 to confirm the selection.

After both the language and the location settings are established, the product automatically turns itself off and then on.

254

Chapter 6

Troubleshooting

ENWW

Soft reset
Before performing an NVRAM init, attempt a soft reset, which does not reset configuration settings or cause a loss of data.

Performing a soft reset


To perform a soft reset 1. 2. 3. 4. 5. 6. Press Menu. Simultaneously press and then release the * button and the # button to open the developer's menu. Press the < or > button until the message REINIT FFS appears on the second line of the controlpanel display. Press .

The process takes approximately 2.5 minutes. During that time, the control-panel display will change several times before returning to Ready. When the Ready message appears on the control-panel display, press Cancel to exit the developer's menu.

Super NVRAM init


When a super NVRAM init is performed, the all-in-one language and telecom country/region settings are undefined. The user is prompted to set the language and telecom country/region. Until these settings are defined, the all-in-one will not return to the Ready state. CAUTION A Super NVRAM init erases all data that is stored in both the unprotected and protected NVRAM memory.

To perform a super NVRAM init


1. 2. 3. 4. 5. 6. Turn off the all-in-one. Press and hold down the * and 5 buttons. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout the entire power-on sequence. When Permanent Storage Init. appears on the control-panel display, release the buttons. When prompted, set the language and telecom country/region. Allow the all-in-one to return to Ready before using it.

ENWW

Service-mode functions

255

NVRAM init
NVRAM init returns all stored parameters in NVRAM to factory default values or to a default ROM value, depending on the variable, and performs a system reset. Performing NVRAM init can cause the all-in-one to violate local telephone regulations. Reset the language and country/region after performing an NVRAM init. An NVRAM init resets the following settings and information: All menu settings are reset to factory default values, including the fax header and company name. Factory settings such as formatter number, page counts, and paper settings are reset. All faxes in memory are erased. All speed-dials, group-dials, and phone book entries are erased. All localization settings, including language and country/region, are reset.

To perform an NVRAM init


1. 2. 3. 4. 5. Turn off the all-in-one. Press and hold down the * and buttons.

Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout the entire power-on sequence. When Permanent Storage Init. appears on the control-panel display, release the buttons. Allow the all-in-one to return to Ready before using it.

256

Chapter 6

Troubleshooting

ENWW

You might also like