Professional Documents
Culture Documents
Subsurface Exploration
PART 1
Topics Covered
I. SUBSURFACE EXPLORATION PROGRAM II. EXPLORATORY BORINGS IN THE FIELD III. PROCEDURES FOR SAMPLING SOIL IV. OBSERVATION OF WATER LEVELS
8/9/2013
SUBSURFACE EXPLORATION
Site investigation, in general deals with determining in general, THE SUITABILITY OF THE SITE FOR THE PROPOSED CONSTRUCTION.
Site Investigation
8/9/2013
Introduction:
WHAT? Attempt at understanding the subsurface conditions such as:
SOIL AND ROCK PROFILE GEOLOGICAL FEATURES OF THE REGION
POSITION AND VARIATION OF GROUND WATER TABLE PHYSICAL PROPERTIES OF SOIL AND ROCK CONTAMINATION, IF ANY GENERAL DATA OF ADJACENT STRUCTURES, HYDROLOGICAL DATA, TOPOGRAPHY, SOIL MAPS, SEISMICITY, ETC.
Introduction (Contd)
WHY? To DETERMINE THE TYPE OF FOUNDATION required for the proposed project at the site, i.e. shallow foundation or deep foundation. To make RECOMMENDATIONS REGARDING THE SAFE BEARING CAPACITY or pile load capacity since it is the subsoil that provides the ultimate support for the structures.
8/9/2013
TO AVOID THIS!
THIS!
Foundation Weakening Due to Soil Liquefaction in Adapazari, Turkey
8/9/2013
THIS!
A sinkhole covers a street intersection in downtown Guatemala City, Wednesday, June 2, 2010. Authorities blamed heavy rains caused by tropical storm Agatha as the cause of the crater that swallowed a a three-story building but now say they will be conducting further studies to determine the cause.
AND THESE!
SINKHOLES
8/9/2013
Introduction (Contd)
HOW?
The three important aspect are PLANNING, EXECUTION and report writing.
PLANNING
To minimize cost of explorations and yet give reliable data. Decide on quantity and quality depending on type, size and importance of project and whether investigation is preliminary or detailed.
Introduction (Contd)
EXECUTION: COLLECTION OF DISTURBED AND/OR UNDISTURBED SAMPLES of subsurface strata from field. CONDUCTING IN-SITU TESTS OF SUBSURFACE material and obtaining properties directly or indirectly. STUDY OF GROUND WATER CONDITIONS and collection of sample for chemical analysis. Geophysical exploration, if necessary. Laboratory testing on samples
8/9/2013
Introduction (Contd)
A complete site investigation will consist of: PRELIMINARY WORK Collecting general information and already existing data such as study of geologic events , seismic maps, etc. at or near site. Study site history if previously used as quarry, agricultural land, industrial unit, etc. SITE RECONNAISSANCE: ACTUAL SITE INSPECTION. To judge general suitability Decide exploration techniques
Introduction (Contd)
EXPLORATION
PRELIMINARY INVESTIGATIONS: Exploratory borings or shallow test pits, representative sampling, geophysical investigations, etc DETAILED INVESTIGATIONS: Deep boreholes, extensive sampling, in-situ testing, lab testing, etc. DEPTH AND SPACING: In general, depth of investigation should be such that any/all strata that are likely to experience settlement or failure due to loading. Spacing depends upon degree of variation of surface topography and subsurface strata in horizontal direction.
8/9/2013
Depth of Boring
The approximate required minimum depth of the borings should be predetermined. The estimated depths can be changed during the drilling operation, depending on the subsoil encountered. To determine the approximate minimum depth of boring, engineers may use the following rule:
8/9/2013
Depth of Boring
For hospitals and office buildings, the following rule could be use to determine boring depth
8/9/2013
DEPTH OF BORING
Approximate depths of borings for buildings with a width of 30m
No. of stories 1 2 3 4 5
SPACING OF BOREHOLES
10
8/9/2013
11
8/9/2013
Soil
Sandy soil
Soil Colour
Gray 7.5YR 5/1
Finds
Modern Rubbish (filled soil)
Chronology
1980s
L2
L3 L4 L5 L6 L7
Sandy soil
Sandy soil Sandy soil Loamy soil Loamy soil Loamy soil, with some decomposed bed rock texture
1980s
1980s 1980s
12
8/9/2013
Helical auger
13
8/9/2013
Continuous-flight auger
14
8/9/2013
Methods of Boring
WASH BORING:
A casing is driven with a drop hammer. A hollow drill rod with chopping bit is inserted inside the casing. Soil is loosened and removed from the borehole using water or a drilling mud jetted under pressure. The water is jetted in the hole through the bottom of a wash pipe and leaves the hole along with the loose soil, from the annual space between the hole and wash pipe. The water reaches the ground level where the soil in suspension is allowed to settle and mud is recirculated.
15
8/9/2013
16
8/9/2013
Wash Boring
Methods of Boring
Another example of wash boring is called mud rotary drilling (soil) or core drilling (rock). MUD ROTARY(ROTARY DRILLING)
Hollow drill rods with a drill bit is rotated into the soil. Drilling mud is continuously pumped into the hole. The bit grinds the soil and the return flow brings the cuttings to the surface.
17
8/9/2013
ROTARY DRILLING
18
8/9/2013
Methods of Boring
PERCUSSION DRILLING: often used to penetrate hard rock for subsurface exploration or for the purpose of drilling wells.
PERCUSSION DRILLING
19
8/9/2013
DISTURBED
(The structure of the soil is disturbed to a considerable degree)
UNDISTURBED
(The true in-situ structure and water content is retained as closely as possible)
Remoulded Wash
Representative
Block
Drive
20
8/9/2013
DISTURBED SAMPLES used for determining index properties (ex. gsd, consistency, etc.) UNDISTURBED SAMPLES used for determining engineering properties (ex. Density, water content, shear strength parameters, etc.) WASH SAMPLES obtained from wash boring water or mud. REPRESENTATIVE SAMPLE retains all constituents of the soil, but is disturbed from natural state and structure. (ex. Split spoon sampler) BLOCK SAMPLES are carved out form sides or bottoms of excavations, sealed in a box and taken to lab. OPEN DRIVE SAMPLERS consist of thin walled tubes which are driven or pushed into the soil at the bottom of the hole. (ex. Shelby Tube sampler)
Undisturbed Samples
21
8/9/2013
22
8/9/2013
DEGREE OF DISTURBANCE
Good quality samples necessary.
AR<10%
soil
AR
23
8/9/2013
Methods of Sampling
Requirements to minimize disturbance to samples
Area ratio = (D2w-D2e) x 100% D2e Area ratio should be as low as possible. (<10%). It represents the amount of soil displaced. Inside clearance = (Ds-De) x 100% ratio De
The inside clearance allows elastic expansion of the sample and minimizes frictional drag on the sample. The inside clearance should be between 0.5% to 3%. The outside clearance = (Dw-Dt) x 100% ratio Dt Outside clearance is necessary to reduce the driving force and resistance to withdrawal. The outside clearance should be between 0% and 2%. Diameter of samples should not be less than 38mm. (Generally between 50-150mm).
24
8/9/2013
25
8/9/2013
UNDRAINED SHEAR STRENGTH OF CLAY cu = KN60 where: K = constant = 3.5 6.5 kN/m2 N60 = standard penetration number obtained from the field
For frictional soils (sands, gravels, silty sands, etc), the strength of the soil increases with the effective overburden stresses v. The greater the depth of the soil, the greater v and the greater the strength of the soil will usually be (within some limits). Thus the greater the depth, the greater the N value usually is in the SPT. Thus the raw N value is not just a soil property, but also a depth property.
Therefore we need to correct N for frictional soils,
(N1)60 = CNN60
where: (N1)60 = corrected N value to a standard value of 95.6kPa (2ksf). CN = correction factor N60 = N value obtained from the field
26
8/9/2013
RELATIONSHIP BETWEEN RELATIVE DENSITY (DR) AND (N1)60 FOR FINE TO MEDIUM SAND: Dr (%) = 1.55(N1)60 + 40 [for 0 (N1)60 25] Dr (%) = 0.84(N1)60 + 58.8 [for 25 (N1)60 50]
FOR FINE TO MEDIUM SAND WITH FINES (THAT IS, % PASSING NO.200 SIEVE, FC) BETWEEN 15% AND 20%, (N1)60 = (N60 +12.9)(
EFFECTIVE PEAK ANGLE OF FRICTION OF GRANULAR SOILS, ' (deg) = 27.1 + 0.3(N1)60 0.00054[(N1)60]2
CORRELATION AMONG N60, ', ' = tan-1 where: N60 = field standard penetration number = effective overburden pressure Pa = atmospheric pressure in the same unit as o (100 kN/m2) ' = soil friction angle SIMPLE CORRELATION BETWEEN ' AND (N1)60:
' =
27
8/9/2013
28
8/9/2013
29
8/9/2013
30
8/9/2013
SIGNIFICANCE
Determine flow directions Identify changes in gradients Measurements for aquifer testing Determine the volume of water or drawdown in the well casing for proper purging
31
8/9/2013
MANUAL METHODS
The usual basic measurement in groundwater studies is that of water levels in wells. If water is encountered in a borehole during a field exploration, it should be recorded. In soils with high hydraulic conductivity, the level of water should stabilize about 24 hours after completion of the boring.
32
8/9/2013
33
8/9/2013
34
8/9/2013
35
8/9/2013
PRESSURE TRANSDUCERS
Pressure transducers are temperature sensitive and cables are subject to stretching with time.
end
36