Professional Documents
Culture Documents
INPUT DATA Working (Serviceability) load = Ultimate tension load N* t = Proof load Tt ( kN) = 4875 (Stressing load) Lock off load (kN) = 4125
Long term load in anchorage(kN) =
10837N
27-Sep-13
3750 5625
Load Factor = 1.5 (The required load necessary to ensure that the structure behaves in a satisfactory manner) 2 ( BS 8081-1989 Clause B5.1 proof load = 1.25 * working load for temp anchors, RBP uses 1.3, and 1.5 * working load for permanent anchors) (BS 8081-1989 recommends 1.1* Working load) 3750 (Designer to enter value) usually equal to working load 4 2 Horiz. Spacing of anchors = 550 mm 2 Vert. Spacing of anchors = 550 mm
kN. KN.
Draw in at lock off = 1 Minimum extension required = Density of rock = Angle of rock cone = Grout strength = Shear strength of rock =
Depth of soil over rock =
mm 2 mm 1-Mar-08
Density of soil
18 45 40 0 0 18
Kn/m^3 Ref: Geotech Report 45298 dated Degrees from vertical. By : Douglas Partners MPA. KPA. (Assume zero KPA. if rock is fractured) mm. Kn/m^3
NOT APPLICABLE 56.0 N*/anchor = 1406 KN. UTS/anchor = 2537 KN. Max. Allow anchor load = 1268 KN. Working load = 937.5 Kn/anchor Proof (Stressing) load = 1219 KN. /anchor Lock off load = 1031 KN. /anchor CALCULATION OF BOND LENGTH ANCHORAGE BOND LENGTH OF STEEL TO GROUT Based on BS 8110 Part 1 1985 Clause 3.12.8.4 Design ultimate anchorage bond stress = =
Adopt Adopt
NOT APPLICABLE.
56
(General rule used by VSL that the of the ultimate strength of the anchor)
beta = .40
fc cube =1.25*f'c
2826
SHEAR STRESS IN GROUT COLUMN Based on AS 1481-1978 Clause 5.10.4 Design ultimate average shear stress = Bond length required (mm) = Bond length required (mm) = 1.5 * 2.8 MPA = NOT APPLICABLE 1178 4.2 MPA. AS PERMANENT ANCHOR AS TEMPORARY ANCHOR
Design ultimate shear stress = 0.45 MPA. (=1.5* Working bond stress) 0 125 Adopted drill hole dia.= 150 O.K. Bond length required (mm) = NOT APPLICABLE AS PERMANENT ANCHOR Bond length required (mm) = 6631 AS TEMPORARY ANCHOR or (min) = 3000 Rock type Strength grade Mpa Basalts, Tuffs 20-80 ROCK CONE PULL-OUT RESISTANCE Sandstones, mudstones 20-80 Granite 20-80 SINGLE ANCHOR Fine grained s'stone 20-80 Slates, slaty shale 20-80 Based on: 0.8 * Wt. Rock cone = 1.5 * Tension load in the group of anchors. Grey shale Phyllite 13-50 Required rock cone length = 4534 mm. overlying soil not taken into account Required rock cone length = 5000 mm. overlying soil taken into account baL O.K.
Mpa.
MULTIPLE ANCHORS Based on: 0.8 * Wt. Rock cone = 1.5 * Tension load in the group of anchors.
6000 6000
mm. mm.
overlying soil not taken into account overlying soil taken into account O.K.
AT ANCHOR STRESSING LOAD, EXTENSION >= MIN REQUIRED EXTENSION AND/OR >= DRAW IN+REQUIRED EXTENSION AT LOCK OFF FREE LENGTH REQUIRED = 3000 = =
NA OK 3000
NOT APPLICABLE 8 EXTENSION AT LOCK OFF LOAD (mm) = NOT APPLICABLE 7 LOCK OFF EXTENSION + DRAW IN EXTENSION = 8
AS PERMANENT ANCHOR AS TEMPORARY ANCHOR AS PERMANENT ANCHOR AS TEMPORARY ANCHOR (SHOULD BE LESS THEN EXT. AT PROOF LOAD)
y/m x/n L #DIV/0! #DIV/0! 1.1 1.1 0.55 0.55 0.366667 0.366666667 0.275 0.275 0.22 0.22 0.183333 0.183333333 0.157143 0.157142857 0.1375 0.1375 0.122222 0.122222222 0.11 0.11 0.1 0.1 0.091667 0.091666667 0.084615 0.084615385 0.078571 0.078571429 0.073333 0.073333333 0.06875 0.06875 0.064706 0.064705882 0.061111 0.061111111 0.057895 0.057894737 0.055 0.055 0.052381 0.052380952 0.05 0.05 0.047826 0.047826087 0.045833 0.045833333 0.044 0.044 0.042308 0.042307692 0.040741 0.040740741 0.039286 0.039285714 0.037931 0.037931034 0.036667 0.036666667
Vc 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000 10500 11000 11500 12000 12500 13000 13500 14000 14500 15000 0 1.884956 15.07964 50.8938 120.6372 235.6194 407.1504 646.5398 965.0973 1374.133 1884.956 2508.876 3257.203 4141.247 5172.318 6361.725 7720.778 9260.787 10993.06 12928.91 15079.64 17456.57 20071.01 22934.25 26057.63 29452.43 33129.98 37101.58 41378.55 45972.18 50893.8
CT Stress Bar with no dead end plate CT Stress Bar with no dead end plate
REQUIRED BOND LENGTH (MM) = REQUIRED FREE LENGTH (MM) = REQUIRED ROCK CONE LENGTH =
JOB NO.
10837N
CONC. FOOTING
ROCK CONE
FREE LENGTH
3000
6000
ROCK
18 kn/m^3
ANCHOR LOADS AND EXTENSIONS WORKING LOAD (KN) IN EACH ANCHOR LOAD FACTOR ULTIMATE LOAD (KN) IN EACH ANCHOR 937.5 1.5 1406 2537 1219 1031 937.5 2 1
EQ.
6631
45
45
BOND
EQ.
ANCHOR
9631
EXTENSION (mm)
4
550 550 mm. mm.
ULTIMATE STRENGTH (KN) OF EACH ANCHOR PROOF (STRESSING) LOAD (KN) IN EACH ANCHOR LOCK OFF LOAD (KN) IN EACH ANCHOR LONG TERM LOAD (KN) IN EACH ANCHOR MIN ALLOWABLE EXTENSION (mm) MAX. ALLOWABLE DRAW IN AT LOCK OFF (mm)
8 7
INPUT DATA
ANCHOR GROUP WORKING LOAD = LONG TERM LOAD IN ANCHOR GROUP =
1-Mar-08
BOND AT GROUT / GROUND INTERFACE AS PERMANENT ANCHOR AS TEMPORARY ANCHOR Design ultimate shear stress = 0.45 MPA. AS PERMANENT ANCHOR AS TEMPORARY ANCHOR
NOT APPLICABLE 56
Bond length required (mm) = NOT APPLICABLE Bond length required (mm) = 6631 or (min) = 3000 CALCULATION OF BOND LENGTH ANCHORAGE BOND LENGTH OF STEEL TO GROUT Anchorage bond length required (mm) SHEAR STRESS IN GROUT COLUMN = 2826
ROCK CONE PULL-OUT RESISTANCE Design ultimate average shear stress = Bond length required (mm) = Bond length required (mm) = 4.2 MPA. NOT APPLICABLE 1178 AS PERMANENT ANCHOR AS TEMPORARY ANCHOR SINGLE ANCHOR Required rock cone length = Required rock cone length = MULTIPLE ANCHORS Required rock cone length = Required rock cone length = 6000 6000 mm. mm. overlying soil not taken into account overlying soil taken into account 4534 5000 mm. mm. overlying soil not taken into account overlying soil taken into account
9631
PROJECT:
JOB NO.
10837N
27-Sep-13
35