Professional Documents
Culture Documents
800-848-6657 USA/Canada
941-927-1414 Intl. 941-927-1612 Fax Sales@baumtools.com www.baumtools.com
800-520-7715
www.baumtools.com
NE
NE
#BINJSEATCUT Use for cutting the head where the injector sits for a clean seat. (CDI) Injector Puller Set
#B900-0199 Use to remove broken glow plugs. Comes with 1/4, 8mm and 10mm Taps. (CDI) CDI Injector Puller Set
NE
NE
#B611-0033PLUS Use to pull out the Bosch style injectors on the CDI engines. Injector Puller Set N
#B667-0363 Use to pull out the injectors on the CDI engines. 2 style claws for tight places Deluxe Injector Puller Kit
EW
NE
#B611-0033LONG Use to pull out the Bosch style injectors on the CDI engines with extra long slidehammer
#BCDIINJPLUS Use to pull out the injectors, and cut the injector seat.
800-519-4097
Item appearances may very 03052011
#ST51-27
Application: Special deep broached 27mm socket to remove injection nozzles without damaging the return pipe. Diesel models 1967-1995. Engines: 601, 602, 603, 615, 616, 617
#606-0009
Application: Special deep broached 22mm socket to remove injection nozzles without damaging the return pipe. Diesel models 1996-2001. Engines: 604, 605, 606
#615-0007
Application: Special slotted socket wrench for removing the retainer nut of the pre-combustion chamber. Use with extractor #602-0033. Engines: 615, 616, 617 (1967-1985)
#ST3000
Application: Special serrated male socket for the retainer nut of the pre-combustion chamber. Use with extractor #602-0033. Engines: 602, 603, 604, 605, 606 (1986-1999)
#902-0033B
Application: Impact extractor for removing diesel pre-combustion chamber on all models from 1967-1999. Extractor adapter has both course and fine threads for early and late models. Use with #615-0007 or #ST3000. Engines: 601, 602, 603, 604, 605, 606, 615, 616, 617.
#602-0033 (Kit)
#601-0521
Application: This pin is used to position the diesel injection pump at its optimal timing position during installation. 1982-1998. Engines: 601, 602, 603, 605, 606, 617 (from 1982)
800-519-4097
#901-0053
12X1.25mm
#917-0053
18X1.25mm
#KO4133
Application: Special serrated socket to remove the injection delivery valve from the injection pump for service. Engines: 601, 602, 603, 605, 606, 617 (from 1982 onward)
For removing heavy carbon deposit from glow plug hole which is a major cause of glow plug failure. Engines: 601, 602, 603, 617.95 Engines: 615, 616, 617
NE
#B606-0053 #B606-0053KIT Use to ream the carbon build up out of the glow plug hole. Engines: 604, 605, 606, 642, 648
Application: Special 12x1.25mm extra long threaded reamer for removing heavy carbon deposit from glow plug hole which is a major cause of glow plug failure. For models from 1996 to end of production. Engines: 604, 605, 606
M70TEK Kit contains: GAUGE - 1000 psi with quick connect and pressure release. M70TE Injection Nozzle Adapters M70TE/1 Mercedes, VW and Audi - 24X2.0mm M70TE/1A Mercedes (Late model) - 22X1.5mm M70TE/6 Nissan M70TE/7 BMW - 24X1.5mm M70TE/8 VW (TDI) - 10X1.0 Glow Plug Adapters M70TE/2 Mercedes, VW and Audi - 18X1.5mm M70TE/2A Mercedes (Late Model) - 12X1.5mm M70TE/3 GM M70TE/4 Isuzu M70TE/5 Toyota
#M70TEK
800-519-4097
Use to measure the engine oil level. Engine: 112, 113, 271, 272, 642, 646, 647, 648 Engine: 103, 104, 111, 119, 120, 603, 604, 605, 606
NE
Meta
#642-0009 Mercedes Benz 84mm x 14 Flats oil filter wrench. Fits Dodge Sprinter, Mercedes E320, Jeep Cherokee 3.0L Diesel (Bluetech Diesels) Common Rail Injector Back Flow Tester
#B1924
Includes 9 adapters to fill Mercedes Benz 722.9 transmissions along Porsche, with VW/Audi CVT, DSG, and standard transmissions and more.
#B611-0421 Use to measure fuel return rate from injectors in common rail diesels.
800-519-4097
#QP1000
Mercedes S-Class W123 and W126 chassis are prone to failure of the torsion bar end. With this kit the torsion bar can remain on the vehicle and the job takes about 1 hour, or 20 hours to remove and install a new swaybar.
The kit includes new bushings, washers. bolt and special stainless steel repair piece.
#B202-0043
Use to remove and install the rear axle carrier mount bushing Mercedes W203, 209, 171
#315140
Use to remove and install the control arm from the hydraulic mount while still on the car. R50, R52, R53 chassis
#315150
Use to remove and install the lower control arm bushing on Mini Cooper R50, R52, R53, R55, R56
800-520-9757
www.baumtools.com
#220-0343 #116-0462
Use to install the steering knuckle ball joint with the knuckle on the car W116, W123, W126 chassis Presses the ball joint into the steering knuckle on 211 (E-class from 2002); 215 (CL-Class from 2002); 219 (CLS-Class from 2006); 220 (S-Class from 2000); 230 (SL Class from 2003)
Use to remove the top seal and the front Airmatic Suspension strut. Use #900-0007 to remove the valve from the strut W220 chassis
800-520-9757
www.baumtools.com
#B202-0143 Use to remove and install tool for rear rubber mount on the lower wishbone for W170 and W202 chassis. Also installs front mount on W208 chassis
#B210-0043 Use to remove and install the bushing in the lower control arm (wishbone) front & rear W210 chassis
#B220-0643 Use to remove and install the front lower control arm bushing W203, 220, 221, 171, 209, 211, 215, 219, 230
#B140-1143 Use to remove and install the lower control arm bushing W140 chassis
800-520-9757
www.baumtools.com
#B234MASTER
This kit quickly pushes the axle out of the hub, and removes the hub. Includes: hydraulic ram, 4 lug and 5 lug adapters, and slide hammer. Hydraulic pump not included. 10 ton recommended
#B90/3
On the car press kit removes and installs hubs. Not for ABS equipped models
#B90K
The B90K is a press kit that REMOVES and INSTALLS front and rear wheel bearing with the spindle ON THE CAR. Saves Time and Makes Money. Our Best Coverage Yet Use with #B90/3 or B234MASTER for ABS equipped models
800-848-6657
www.baumtools.com
Spring Compressors
MACPHERSON STRUT SPRING COMPRESSOR
#1117J
Compresses all types of MacPherson style coil springs front and rear. Includes three sets of jaws 75-110mm 110-140mm 140-190mm Fits most Mercedes Benzs and many other vehicles.
#924-0231 Compresses front and rear axle springs in the car on models with idler arm Chassis: 107, 114, 116, 123, 124, 126, 129, 140, 164, 170, 171, 201, 202, 203, 204, 208, 210, 211, 219
800-520-9757
www.baumtools.com
A
Kit Contents: Pump Assembly A Nut and Ferrules B 722.9 Mercedes Benz Adapter #1 VW/Audi Straight Adapter #2 VW/Audi Short Adapter #3 VW/Audi Long Adapter #4 VW/Audi CVT Adapter #5 VW/Audi DSG Adapter #6 Ford Transmission Adapter #7 Universal Adapter #8
B 3 2 8
7 6
4 1
#B1924
800-520-9757
www.baumtools.com
W E N
#B70A
Power Supply Features Constant voltage output selectable from 13.0 to 14.8V DC Output current up to 70 amps Clean power for flash reprogramming Provides power to vehicles on display Battery Charger Features Fully automatic operation for 12V batteries Works with regular automotive, deep-cycle, AGM, and gel cell battery types Variable charge rates 4/20/70 amps Digital volts and amps display Manual mode with digital timer Unit Features 120/220 VAC 50/60 Hz Input Microprocessor controlled operation Extra long 9 line cord with 20A plug Extended reach 9 output cables Heavy duty clamps with replaceable jaws Large carrying handle or can be permanently mounted to a shop vehicle lift Dual temperature controlled cooling fans Durable anodized aluminum case Can supply a constant voltage for flash reprogramming UL/CUL approved
www.baumtools.com / sales@baumtools.com
800-519-4097
Includes: Coding and Programming Principles, I and K Body Bus Systems, Throttle Body MDK - EDK - EML Systems, EWS System I, II, III, CAS System (Car Access System) E65, ABS - DSC III (Dynamic Stability Control), Instrument SRI Resetting Procedures, E65 CBS (Condition Base Service) System
Check our website for additionl Training and Reference titles for European cars, plus more:
AMERICAN CARS
GM, FORD, CHRYSLER
ASIAN CARS
TOYOTA/ LEXUS HONDA/ACURA NISSAN/ INFINITI MITSUBUSHI MAZDA SUBARU HYUNDAI KIA SUZUKI ISUZU DAIHATSU DAEWOO
Now get high end German and Swedish proprietary coverage with deep Asian and Domestic
800-848-6657
www.baumtools.com
Application Model M116, 117 Use to install Timesert insert when the cylinder bolt holes strip in the light alloy type engine case. Use with Timesert kit #TS1015 and insert #TS10155
TS1015
Application Timesert kit for rethreading case when cylinder head bolts strip out. Use with alignment jig #117-0223 and insert #TS10155
TS10155
H992LG-T55
Application Special round shaft 96mm long socket for the T55 TORX socket head bolt on cylinder head of late model 6 and 8 cylinder engines.
ST1054-10
Application Use this long Allen head socket to remove and install cylinder head bolts.
Model M100, 110, 114, 115, 130, 180, OM615, 616, 617
ST1054-5
Tool Name Application HEX HEAD SOCKET - 5mm x 180mm long body for various engine bolts. 5mm x 180mm 1/2" DRIVE
Model All
Page #1
Sarasota, FL 34231
Tool Name Application HEADBOLT SOCKET Special 130mm long T55 TORX head bolt socket for 112 - TORX T55 engines. Use with #H992LG-T55 to remove all bolts. Mercedes #000-589-0310
ST3004
Application XZN Hex Head Socket-12mm x 55mm 1/2" drive with special short format for cylinder head bolts.
ST3054/8L
Tool Name Application Model HEX HEAD SOCKET - 130 mm long, 1/2" square drive, for Allen screws on cylinder M115, 116, 117 8mm X 130mm 3/8" head. DRIVE
ST3054X-M8
Tool Name XZN HEX HEAD SOCKET - 8mm X 140mm 1/2" DRIVE
Application Use to remove and install cylinder head bolts. Tri-square socket head screws (XZN). 8mm 12 point 1/2 square socket, 140 mm long for screws on cylinder head.
ST3054XM10
Tool Name XZN HEX HEAD SOCKET - 10mm X 140mm 1/2" DRIVE
Application Use to remove and install cylinder head bolts. Tri-square socket head screws (XZN). 10mm 12 point 1/2 square socket, 140 mm long for screws on cylinder head.
Model M112, 113, 137, 127, OM602, 603, 604, 605, 606, 612, 613, 628, 629, 647, 648 Model M102, 103, 104, 110, 116, 117, 119, 120, 615, 616, 617
ST3054XM12
Application Use to remove and install cylinder head bolts. Tri-square socket head screws (XZN). 12mm 12 point 1/2 square socket, 140 mm long for screws on cylinder head.
Page #2
Sarasota, FL 34231
Tool Name Application Model UNIVERSAL HEX Use to remove cylinder head bolts at rear of case. Use with M116, 117 HEAD SOCKET - 8mm sockets #ST3054-8G and #916-0013. 3/8" DRIVE.
916-0013
Tool Name Application HEX HEAD SOCKET - Use to access head bolts under rocker shaft for R&R and 8mm C 1/2" DRIVE torquing. (See #ST3054-G8 and #ST3149-8)
001-0016/2
Application Special 16mm wrench designed to remove the nuts from Mercedes Benz engine mount.
001-0016/9
Application Special 17mm wrench designed to remove the nuts from Mercedes Benz engine mount.
103-0114
Application Use to install the camshaft sealing ring with cover on. Protects seal lip from damage.
119-0014
Model M119
Page #3
Sarasota, FL 34231
Tool Name Application Model VIBRATION DAMPER Holds vibration damper when loosening and tightening M112, M113, COUNTER-HOLDER center bolt. Handle can be extended with commercially M137 available pipe, e.g. 3/4 din 2441, diameter 26.9 x 3.25 mm, length 1000 mm
230-0040
Tool Name Application Model VIBRATION DAMPER Holds vibration damper when loosening and tightening W219, 230, COUNTER-HOLDER center bolt. Handle can be extended with commercially 240, 271 available pipe, e.g. 3/4 din 2441, diameter 26.9 x 3.25 mm, length 1000 mm
110-0040
112-0340
Application Model Use to lock crankshaft on starter ring gear (mount in starter M112, 113, 137 hole) for vehicles with left and right-hand steering.
116-0140
285-0240
Page #4
Sarasota, FL 34231
Application Locks flywheel at starter ring gear from the transmission side.
Model M102, 103, 104, 111, 601, 602, 603, 604, 605, 606, 611, 612, 613
602-0040
Model M102, 103, 104, 111, 120, 137, 601, 602, 603, 604, 605, 606
ST51-27
Application 12 point 1/2" DR. socket for loosening and tightening the center bolt of the crankshaft. All models except 100.
Model All
110-0761
Tool Name Application Model CRANKSHAFT Use to press in the front crankshaft radial seal ring for pulley M110, 116, 117, SEALING RING end of crankshaft. 123 SLEEVE INSTALLER
111-0843
Application Tool for pressing rear crankshaft radial seal into position on crankshaft. Additional sleeve with 3 mm offset to the inside for later models.
Model M102, 111, 112, 113, 137, 275, 601, 602, 603, 604, 605, 606, 628
119-0114
Tool Name Application For pressing in the front crankshaft radial seal ring. FRONT CRANKSHAFT SEAL RING SLEEVE
Page #5
Sarasota, FL 34231
Application Installing tool for dipstick allows easy installation in most models. Vehicles with left and right-hand steering.
Model M102, 103, 104, 111, 116, 117, 119, 601, 602, 603, 615, 616, 617
KK22-1
Application Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)
Model All
KK21-0
Model All
KO4012M
Tool Name Application SHORT HEX HEAD Short hex head sockets for access to tight locations. Sizes SOCKET - 1/2 "DRIVE available 4, 5, 6, 8, 10, 12, 14, 17 and 19mm. 12, 17 and 19mm most common for Mercedes.
Model All
KO4012M-14
Tool Name Application 1/2" drive stubby hex 14mm socket for oil drain plugs OIL DRAIN HEX HEAD SOCKET 14mm 1/2" DRIVE
Model All
B3676
Application Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)
Model W107, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220
Page #6
Sarasota, FL 34231
Tool Name Application OIL DRAIN WRENCH Use to service oil, differential and transmission drain plugs. - 14mm HEX X 17mm BOX
W1088
Model M110, 107, 116, 117, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220, 615, 616, 617, 716, 717 Model All
Application Universal pilot bearing and bushing puller. Particularly narrow format and sharp lip allows access to even the hardest to get at bushings and bearings without damage.
Tool Name Application CAM ALIGNMENT KIT Use to lock cams and flywheel on a range of Mercedes Benz models. kit includes flywheel locks and camshaft retaining pins.
B112-0001K
Model 102, 103, 104, 111, 112, 113, 119, 137, 272, 273, 601, 602, 603, 604, 605, 606, 611, 612, 613, 628, 629, 640, 642, 646, 647, 648
Tool Name Application Model CAM ALIGNMENT KIT This kit contains the intake and exhaust cam alignment jigs 112, 113 and the cam holding wrench. Kit includes 112-0001, 112-0132, and 112-0032.
B271-0140
Tool Name Application Model 271 CAM TIMING KIT Use to setup and hold cam timing during chain replacement. M271 Kit includes 271-0140, 271-0061, 271-0015, 271-0031
Page #7
Sarasota, FL 34231
Application (2 pairs) each connected with flexible tubing, for holding camshaft in installation position (25 after ignition TDC)
137-0140
Application Model M137, 275 Used to hold camshafts in position 30 degrees ATDC; for loosening and tightening the bolt that attaches the camshaft sprocket or to adjust cam timing (2 pieces). Use with #137-0040
285-0040
Application Only for left bank of cylinders. This retaining device is designed for positioning the camshaft in 30 degrees after TDC position.This makes it possible to slacken and tighten the bolts attaching the camshaft sprocket. Use #137-0140 for the right bank of c
285-0140
Application Used to retaining timing chain on sprocket during chain replacement Operation.
M0037
Application Model M115,116, 117 Holds chain tight against cam sprocket so chain cant slip during installation. Cuts time and manpower in half. Early V8 models.
M0037-104
Application Holds chain tight against cam sprocket so chain cant slip during installation. Cuts time and manpower in half.
Model M104
Page #8
Sarasota, FL 34231
Tool Name Application CHAIN LOADER - 119 Holds chain tight against cam sprocket so chain can't slip during Installation. Cuts time and manpower in half.
Model M119
102-0421
Application Use to load timing chain onto sprocket on 6 and 8 cylinder engines.
000-5843
Application Model All Use to press on external lugs and rivets of dip-type fasteners of duplex Roller chain. See #966-5843 to remove rivets.
112-0963
Application Includes: chain guide and press thrust pieces. Use for pressing rivet onto Outer link. Use with rivet pressing tool #000-5843. This set comes with #000-5843.
103-0163
Model M102, 104, 110, 111, 112, 113, 116, 117, 119, 120, 116, 275, 611, 612, 613, 642, 646, 647, 647, 668 Model M102, 103, 104, 111, 112, 113, 116, 166, 602, 603, 611, 612, 613, 640, 646, 647, 648, 668
Application Use with tool #000-5843 to rivet single row timing chains.
966-5843
Tool Name Application Model TIMING CHAIN Use to separate single and double row timing chains without All SPLITTER - SINGLE & damaging links DOUBLE ROW
Page #9
Sarasota, FL 34231
Application Removes tensioner rails and rocker pins. Includes: Slide hammer and 5mm, 6mm, 8mm and 10mm threaded pins.
116-2033P
Model M102, 103, 104, 110, 111, 116, 117, 119, 120, 272, 275, 601, 602, 603, 606, 612, 615, 616, 617, 628, 640, 642
Tool Name Application Model All CHAIN RAIL PIN Replacement threaded rods for #116-2033 chain rail pin PULLER - THREADED puller. Sizes #1160034 - 5x150mm, #116-0134 6x50mm, ROD SET #116-0234 6x150mm, #616-0034 8x150mm and #116-0334 10x100mm spindles.
915-0734
Application Pulls sliding rail pins on all models. Includes: Puller and 5mm, 6mm, and 8mm spindles.
Model All
B116-0134
Tool Name Application THREADED ROD - 6 x Use with chain rail pin puller #915-0734. (1 piece) 8 X 50mm
917-0623
Model M110, 115, 116, 117, 119, 155, 272, 275, OM601, 602, 603, 604, 605, 606, 612, 615, 616, 617, 628, 640, 642
Tool Name Application Model HYDRAULIC LIFTER Measures valve clearance so proper compensating element M116, M117 GAUGE V-8 disk can be installed. from 1978
Page #10
Sarasota, FL 34231
Tool Name Application VALVE SPRING Use with tool #102-0161 for 102. Use with tool #102-0359 COMPRESSOR ARM for 102-16 valve. Use with tool #103-0061 for 103 Use with tool #601-0259 for 601. Use with #111-0059 for all others.
Model M102, 103, 104, 111, 112, 113, 119, 120, OM601, 602, 603, 604, 605, 606
123-0361
Application Model Use to depress valve springs for replacement of seals, M114, 115, 116, stems, or valves on pre 1991 6 cylinder (except 110) and 8 117, 130, 180 cylinder engines through 1991. For 110 engines see #110-0461. All parts are available separately.
M1160
Tool Name VALVE SPRING COMPRESSOR KIT 102, 103, 601 ENGINES
Application Use to depress valve springs for replacement of seals, stems, or valves on Late model 4 and 6 cylinder engines. Includes: #601-0261, #102-0161, #103-0061
116-0101
Application Aluminum wrench for holding and turning camshaft during assembly and timing.
119-0001
Application Double open end wrench 26.5mm X 27.5mm 256mm long for turning camshaft to assembly position.
116-0663
Model All
Page #11
Sarasota, FL 34231
Model M104, 111, 112, 113, 119, 120, 604, 605, 606, 668
116-0043
Application Use to press in the 9mm valve stem seal onto the valve guide sleeve.
ST11063
Model All
615-0001
Application Diesel valve adjusting wrenches. Use with retaining nut holder #615-0003.
615-0003
Application Model Use to hold retaining nut when adjusting valves with wrench 615, 616, 617 pair #615-0001.
900-0307
Application Model Special A/C idler pulley wrench allows access to 8mm bolts M102, 103, 116, on 102 and 103 idler pulley, as well as 10mm bolts on 116, 117 117 V8 models. Also see kit #B9042.
Page #12
Sarasota, FL 34231
Application Direct reading compression gauge with hose and quick connect adapter for diesel engines. Please request adapter when ordering.
Model 601, 602, 603, 604, 605, 606, 615, 616, 617
M70TE/1
Application Model Adapter for early large injection nozzle port. 24mm X 2.0mm 615, 616, 617
M70TE/1A
Application Adapter for later model diesels with small injection nozzle port. 22mm X 1.5mm
M70TE/2
Tool Name Application BOSCH GLOW PLUG Adapter for early large Glow plug port. 18mm X 1.5mm 18X1.5mm - EARLY MERCEDES
M70TE/2A
Tool Name Application BOSCH GLOW PLUG Adapter for later model diesels with small Glow plug port. 12X1.5mm - LATE 12mm X 1.5mm MODELS
Model 601, 602, 603, 604, 605, 606, 612, 617 Turbo
M70TE/X
Application Use to access deep port injectors or glow plugs on late model engines. Use with adapter #M70TE/2A.
Page #13
Sarasota, FL 34231
Application Model Checks the fuel supply, running and leakage pressures of all All types of injection systems. Includes: Gauge (160psi/1100kpa), hoses and fittings and storage case.
1318-R
Application Model Checks charging (supply), running and leakage pressures of Injected all types of injection systems. Includes: Gauge Engines (160psi/1100kpa), 3-way switch, hoses and fittings and storage case.
1318K
Model All
1318/4
Tool Name Application Male to Male adapter with dual conical fittings. MALE ADAPTER 10X1mm X 12X1.5mm
Model All
1318/5
Tool Name Application Model FEMALE ADAPTERS Female to Male adapters. Sizes available 8x1mm x All 12x1.5mm, 10x1mm x 12x1.5mm, 12x1.5mm x 12x1.5mm, 14x1.5mm x 12x1.5mm. Please specify size when ordering.
1318/6
Application Model Male to Male adapters. Sizes available 8x1mm X 10x1mm, All 8x1mm X 12x1.5mm, 8x1mm X 12x1.5mm X 70mm, 12x1.5mm x 12x1.5mm, 14x1.5mm x 12x1.5mm. Please specify size when ordering.
Page #14
Sarasota, FL 34231
Application Threaded banjo rings for testing in tight spots. Sizes available 8mm X 10x1.5mm Male, 10mm X 12x1.5mm. Specify size when ordering.
Model All
1318/10
Model All
000-3323
Application Model Allows synchronizing of dual oval type carburetors with large M114, 130, 180 circular formats found in some foreign model carburetors such as Weber, Zenith...etc. Use with either # 691A or 000-1223.
691STE
Application Model Plug type base with exchangeable tips for different types of All Carbureted carburetors.
ST12975
Application Use to block off fuel line when working on fuel system or removing engine.
Model All
ST11085
Application Tapered reamers allow precision reaming of carburetor main jets, injectors, solenoids and other small orifices. Set includes 13 reamers and pin vise.
Page #15
Sarasota, FL 34231
Application Test the throttle potentiometer used in all late model engines.
ST10507KK-3
Tool Name Application CO ADJUSMENT HEX Use to adjusts CO and idle mixture control screw on fuel SCREWDRIVER injection 3mm X 380mm long distributor. MB #000-589-1411
A0201
Application Model Basic 60 pin break out box to test the contacts, continuity, All inputs and outputs of a variety of electronic control units. Adapters are available for Bosch, Siemens and TEVES 25, 35, 38, 42, 55 and 60 pin connectors as well as many others.
A0202
Application Model Basic 120 pin break out box to test the contacts, continuity, All inputs and outputs of a variety of electronic control units. Adapters are available for Bosch, Siemens and TEVES 25, 35, 38, 55, 68 and 88 pin connectors as well as many others.
A020201
A020202
Page #16
Sarasota, FL 34231
Application KE5.1, KE5.2, ABS 3 & 5 and later, EGS, IFI Diesel, ASR (202).
A020206
OBD2-BOB
102-0463
Application Tests CIS-E electronic idle speed control with standard multimeter. (VOMDMM)
119-0463
Tool Name Application LH FUEL PRESSURE With 7/16-20 tapered SAE angled connection and 12 x HOSE 1.5mm union nut. For LH fuel injection system (use with tester #103-0021).
140-0133
Page #17
Sarasota, FL 34231
Tool Name Application V6 ENGINE SPARK Special angle design with 17mm wrench to be a lever for PLUG BOOT PULLER removing and installing the wires
Model M110/ML
M0035A
Tool Name Application GAS TANK SOCKET - Use to remove fuel tank filter body and fuel gauge sending 46mm units.
Model All
T13-22
Application Use to remove gas tank drain plugs on late model cars. 22mm.
09-Diesel B667-0363
Application Use to pull out the injectors on the CDI engines. 2 style claws for tight places
Model CDI
B611-0033PLUS
Application Model Use to pull out the Bosch style injectors on the CDI engines. CDI
Page #18
Sarasota, FL 34231
Application Model Use to pull out the Bosch style injectors on the CDI engines CDI with extra long slidehammer
B900-0199
Tool Name
Application Use to remove broken glow plugs. Comes with 1/4, 8mm and 10mm Taps. (CDI)
Model CDI
BCDIINJPLUS
Application Use to pull out the injectors, and cut the injector seat
Model CDI
BINJSEATCUT
Application Use for cutting the head where the injector sits for a clean seat. (CDI)
Model CDI
602-0033
Tool Name Application IMPACT EXTRACTOR Slide hammer with #902-0033B threaded adapter for FOR PRE removing the precombustion chambers on diesel models. CHAMBERS - DIESEL
Model 601, 602, 603, 604, 605, 606, 615, 616, 617
902-0033B
Application Model Special slide hammer adapter for removing pre combustion 604, 605, 606, chamber from early and late model Turbo Mercedes diesel 615, 616, 617 models. Use with #602-0033B. Have both coarse and fine threads.
Page #19
Sarasota, FL 34231
Tool Name Application PRE-CHAMBER Use to remove and install the threaded retainer ring of the RETAINER RING PIN pre-chamber. WRENCH - DIESEL
ST3000
Application Multi spline socket for removing pre combustion chamber retainer ring on late model indirect injection diesel models. MB #604 589 0109 which replaced #603-589-0009
B606-0053KIT
Tool Name Application Model GLOW PLUG PULLER Use to remove the glow plug and ream the pre combustion 601, 602, 603, AND REAMER SET chamber 617 Turbo, 642, 648
B606-0053
Tool Name GLOW PLUG BORE REAMER - PENCIL TYPE EXTRA LONG
Application Model Special 12x1.25mm extra long threaded reamer for 604, 605, 606, removing heavy carbon deposit from glow plug hole which is 648 a major cause of glow plug failure. For models from 1996 to end of production.
901-0053
Application Model Special 12x1.25mm reamer for removing heavy carbon 601, 602, 603, deposit from glow plug hole which is a major cause of glow 617 Turbo plug failure. For models from 1983 to end of production.
917-0053
Application Special 18x1.25mm threaded reamer for removing heavy carbon deposit from glow plug hole which is a major cause of glow plug failure. For models from 1967 to 1985. Non Turbo. Universal not included.
Page #20
Sarasota, FL 34231
Tool Name Application GLOW PLUG Use to remove and install the glow plug connectors on S CONNECTOR PLIER class diesel models from 2000 onward.
Model 611, 612, 613, 628, 640, 642, 646, 647, 648
617-0821
Application Position transmitter to measure start of fuel delivery using the RIV method.
M502
Tool Name Application Model DIESEL FUEL Measures the diesel fuel pressure in high pressure CDI type Diesel from PRESSURE TESTER engines. 1997 on
M24D
Application Model Test opening pressure, spray pattern, and cleans injectors. All Diesel Kit includes: Gauge (7000psi/500bar) pump and steel Engines adaptor line. May be upgraded to test gasoline injectors.
601-0008
601-0514
Tool Name Application Model INJECTION PUMP Aligns injection pump for proper timing during removing and 601, 602, 603, CENTERING SLEEVE installing of injection pump. 605, 606 - DIESEL
Page #21
Sarasota, FL 34231
Application Locks diesel pump cam to maintain timing during pump installation.
606-0009
Tool Name Application INJECTION NOZZLE se for removal and installation of diesel injection nozzle. SOCKET - 22mm
900-8673
Application Locks diesel pump cam to maintain timing during pump installation.
916-0021
Tool Name Application Model VACUUM CONTROL Use to measure vacuum pressures to vacuum control valve. 616, 617.91, ADJUSTING ROLLER 617.95
936-0223
B611-0421
Application Model Use to measure fuel return rate from injectors in common Common Rail rail diesels. Diesel Includes adapters and 6 graduate cylinders and 6 graduated bottles.
Page #22
Sarasota, FL 34231
Tool Name Application Special wrench for injection lines. INJECTION LINE CROWFOOT - 17mm 3/8"DR.
KO4133
Tool Name Application Model SERRATED WRENCH Use to remove and install the injection pump stub pipe and 601, 602, 603, SOCKET pressure valve on diesel pumps. 605, 606, 617
ST440-14
Tool Name Application Use to access injection pipe cap nuts. CROWFOOT SOCKET - 14mm 3/8" DRIVE
Model 601, 602, 603, 604, 605, 606, 611, 612, 613, 628, 640, 646, 647, 648, 661, 662, 668 Model 601, 602, 603,612, 615, 616, 617, 646, 647, 648
ST51-27
Application Special 12 point 1/2" DR. socket with interior relief to accommodate the small leakage return tubes on top of injection nozzle. Also available in Hazet brand.
US2568
Application Model Special L wrench to access injection pump mount screws. 601, 615, 616, 617
Page #23
Sarasota, FL 34231
Application This 11 piece wrench set contains 32, 36, & 65mm wrenches for removing fan clutch. Also contains fan clutch holders and V8 fan belt service tools.
Model All
900-0307
Application Model Special A/C idler pulley wrench allows access to 8mm bolts M102, 103, 116, on 102 and 103 idler pulley, as well as 10mm bolts on 116, 117 117 V8 models. Also see kit #B9042.
AS4765
Application Belt remover/installer provides reach and maneuverability to thread the belt around the pulley system. Includes 13mm, 14mm, 15mm, 16mm and 18mm socket, plus 3/8" and 1/2" drives
AS4955
Tool Name Application ALTERNATOR PULLY KIT Use to hold the pulley on the European alternators with a clutch.
15-Ingition 103-0037
Application Model All Use to remove the BERU type wires on late model cars. Wide grip section and special angle make it easy to remove plug wires without separating crimps.
Page #24
Sarasota, FL 34231
Application Model All Use to remove the BERU type wires on late model cars. Wide grip section and special angle make it easy to remove plug wires without separating crimps.
112-0109
Model 112, 113, 137, 155, 166, 266, 271, 272, 273, 275, 902, 906
66US-16
Tool Name Application SPARKPLUG 16mm (5/8") Sparkplug socket with internal magnet for use SOCKET-MAGNETIC- on engines with deep seated peanut sparkplugs. 16mm
Model M102, 103, 104, 111, 112, 113, 119, 120, 137, 272, 273, 275, 902, 903
66US-21
Tool Name Application SPARKPLUG 20.8mm (13/16") Sparkplug socket with internal magnet for SOCKET-MAGNETIC- use on engines with deep seated sparkplugs. 20.8mm
ST3047-12
Application Model Special deep 12mm socket for removing and installing glow 601, 602, 603, plugs in tight spaces. 606
Page #25
Sarasota, FL 34231
Tool Name Application Model OIL LEVEL DIPSTICK Use to measure oil level and check length of oil dipstick M103, 104, 111, guide pipe in shop. See #115-1521 for tulip shaped flared oil 119, 120, dipstick guide tubes found in early models. OM603, 604, 605, 606
120-0721
Tool Name Application Model OIL LEVEL DIPSTICK Use to measure oil level and check length of oil dipstick M112, 113, 271, guide pipe in shop. See #115-1521 for tulip shaped flared oil 272, 642, 646, dipstick guide tubes found in early models. See #120-0621 647, 648 for vehicles 1996-2008. See 275-0021 for 12 cylinder engine M275.
103-0209
Application Socket type filter remover for spin on oil filters and filter housings. Reinforced construction and side lock bolts to remove the most stubborn filters. Also see #H2172.
B1407
Model M102, 103, 104, 111, 112, 113, 119, 120, 137, 155, 272, 275, 285, 611, 612, 613, 628, 646, 647, 648
Tool Name Application Model OIL FILTER SOCKET 3 sockets set 27mm, 32mm and 36mm for oil filter housings 364, 366, 604, SET on Mercedes and Smart cars. 605, 606
B6700
Application Special "vise-grip" action makes this the best oil filter remover yet.
Model All
B6700ADJ
Model All
Page #26
Sarasota, FL 34231
Tool Name Application BLUTECH OIL FILTER Use to remove the oil filter cap on the Bluetech diesel WRENCH engine. 84mm 14 flats
Model 642
B117-0207
Application Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)
Model M102, 103, 104, 110, 116, 117, 119, 120, 601, 602, 603, 604, 605, 615, 616, 617 Model 602, 603, 604, 605, 606
604-0034
Application Use to remove oil injection nozzle from crankcase in combination with impact puller #602-0033.
KO4012M-14
Tool Name Application OIL DRAIN SOCKET - Use to remove and install 14mm oil drain plugs in engine 14mm and transmission. Sizes available 4, 5, 6, 8, 10, 12, 14, 17 and 19mm.
111-0034
Application Model Removes oil injection nozzle from crankcase in combination M111 with impact puller #602-0033
Page #27
Sarasota, FL 34231
Application This 11 piece wrench set contains 32, 36, & 65mm wrenches for removing fan clutch. Also contains fan clutch holders and V8 fan belt service tools.
Model All
103-0040
Tool Name Application Model FAN HOLDING TOOL Use to hold fan pulley while loosening and tightening screws M103, 104 in viscosity fan couplings. Use with tool # 103-0109 or tool # 102-0308. Also see kit #B9042.
113-0040
Application Model Holds pulley when removing and installing fan clutch. Use M111, 112, 113, with open end wrench #111-0201 and torque wrench 119 #001-7221. (Replaces #119-0240 and #111-0040). Also see kit #B9042.
120-0201
Tool Name Application Model FAN HUB WRENCH - Special open-end 65mm wrench for fastening fan hub. Also M103, 104, 119, 65mm see kit #B9042. 120
113-0001
Application Use to loosen and tighten fan clutch. Use with torque wrench #ST730/5 and holding tool #113-0040.
900-0307
Application Model Special A/C idler pulley wrench allows access to 8mm bolts M102, 103, 116, on 102 and 103 idler pulley, as well as 10mm bolts on 116, 117 117 V8 models. Also see kit #B9042.
Page #28
Sarasota, FL 34231
Application Use to hold water pump pulley while loosening and tightening screws. Use with tool # 103-0109.
B113-0001
Application Model Use to loosening and tightening of the fan coupling nut. Use All with holding tool #113-0040. Also see kit B9042.
ST3049-8
Tool Name Application SHORT HEX HEAD Removes screws on viscosity fan couplings and pulley SOCKET - 8mm X facings. (#103-0109) 24mm LONG 3/8" DR.
B1027
Application Special tips allow easy handling of Corbin clamps on radiator and emission control hoses.
ST10623/1
Application Locking type pliers with rotating jaws to access even the hardest to reach clamps. 290mm Long.
ST12506
Application Model Use to remove hose clamps with worm-drive threads. Sizes All 5, 6, 7, 8 and 10mm available. Please specify size when ordering. See # H798-5 for late model "Corbin" clamps. 7mm is the most common Mercedes size.
Page #29
Sarasota, FL 34231
Application Model Special 10mm Allen wrench 500mm long. Use to loosen and M116, 117, 119 tighten the mount bolts of the idler pulley when adjusting v-belt of refrigerant compressor.
H2740
Tool Name SWIVEL HEX HEAD SOCKET - 6mm 3/8" DR. LONG EXTENSION.
Model All
FZ20
Application This is the radiator reservoir adapter for testing reservoir integrity. Models 1996 And later. (MB #210-589 009100)
FZ19
Model W124, 129, 140, 163, 170, 171, 199, 202, 203, 208, 209, 210, 211, 215, 219, 220, 221, 230, 240, 461, 463, 464 Model All before 1968
Tool Name Application RADIATOR ADAPTER Adapts US type radiator pressure testers to early model - EARLY TYPE radiators with large caps.
Tool Name Application UNIVERSAL CLUTCH Use to center clutch disc with clutch pressure plate CENTERING TOOL 15-28mm
Model W107, 123, 124, 126, 129, 140, 163, 168, 169, 170, 171, 201, 202, 203, 208, 209, 210, 211, 245.2, 414, 639
Page #30
Sarasota, FL 34231
Model W107, 123, 124, 126, 129, 140, 163, 170, 201, 202, 203, 208, 210, 460, 461, 463 Model W124, 201, 203, 170
C-26
Tool Name Application CLUTCH ALIGNMENT Center pin for clutch pressure plate. Same as #201-0815. PIN
915-0107
986-1107
Application Removes groove nut on the main shaft and joint flange of manual transmissions.
Model G72
Page #31
Sarasota, FL 34231
Application Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)
KO4012M
Tool Name Application Model 716, 717 OIL DRAIN SOCKET - Use to remove and install 14mm oil drain plugs in manual 14mm transmissions. Sizes available 4, 5, 6, 8, 10, 12, 14, 17 and 19mm.
KK70-A
Application Complete set of ball bearing extractors for 6000-6013, 6200-621, 6300-6311 and 6403-6408 type bearings. Replaces #000-9433 and #001-0233. Replacement arms available.
Model All
KK17-K
Application Special reinforced bearing separator and drive cross member for removing bearing inner race from the drive flange on rear wheel bearing. From Kukko of Germany.
Model All
KK20-10
Application Model All This 2 arm sliding jaw puller is ideal for transmission and differential gears, ball bearings and tapered roller bearings. For applications requiring longer arms see #KK1-250-P for extra long arms (250mm long).
KK21
Application Model Large range of internal extractors for use with #KK22-1 and All KK22-2. Sizes range from 5mm to 100mm in diameter.
Page #32
Sarasota, FL 34231
Application Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)
Model All
KK1-250-P
Application Extra long arms for puller #KK20-10 allows removal of bearings and gears from long shafts, such as reverse and 5th gear.
Model All
KK22-2
Application Large counter stay for use with Kukko extractor #KK21-3 thru #KK21-8.
Model All
ST51-30
Application 12 point 1/2" DR. with thin walls and deep broaching for collar nut on drive flange. Replaces #126-0209.
Application Use to fill the 722.9 transmission, along with VW/Audi and other cars
Model 722.9
Page #33
Sarasota, FL 34231
Application Model Assembly device for snap ring on spring cup of B1, B2, K1, 722.6 K2 and K3.
140-1521
Model 722.6
168-0121
Tool Name Application OIL LEVEL DIPSTICK For determining oil level height.
B9336A
Tool Name Application TRANSMISSION DIP Use to check the transmission fluid level on the Sprinter STICK vans
Model Sprinter
B722-0315
Application Model Use to remove the overflow pipe on the 722.9 Transmission 722.9
B7200
Tool Name
Model All
Page #34
Sarasota, FL 34231
Application 12 point 1/2" DR. with thin walls and deep broaching for collar nut on drive flange.
915-0107
915-0807
986-1107
916-0011
Tool Name Application SECONDARY PUMP Use to remove the screw plug on the secondary pump. SCREWDRIVER
112-0161
Application Model Installs K1 (135mm) 134 ID, 136 OD clutch piston into outer K4A025, disk carrier. K4C025, K4C025(rein), 722.1
Page #35
Sarasota, FL 34231
Tool Name Application CLUTCH PISTON Use to guide the clutch piston K1 (127 mm) and K2 into INSTALLING SLEEVE outer disk carrier (Use with sleeve #201-0214).
126-0414
Application Use to guide the reverse gear piston into front cover.
126-0431
Application Use to measure axial play on front and rear planetary gear set.
126-0621
Tool Name Application MEASURING SCREW For checking free travel on brake band piston B1.
126-1014
Application Use to guide the clutch piston K1 (118 mm) into the outer disk carrier (Use with sleeve #140-0014).
129-0623
Application 3GAUGING DISK For measuring axial play on rear planetary gear set. (HCB A1037-2)
Page #36
Sarasota, FL 34231
Application For guiding clutch piston K1 and K2 into the outer disk carrier. (Use with sleeves #126-0314 and #126-1014).
201-0114
Application Installs K1 (135mm) clutch piston into outer disk carrier. 4 speed.
Model 722.4
208-0021
Application Compresses clutch packs K1, K2, K3 and brake bands B1 and B2. 1000N.
201-1243
Application Installs snap ring on spring plate for K1, K2, B3.
201-0359
201-0214
Application Use to guide reverse gear piston into front cover. 4 speed.
Model 722.4
Page #37
Sarasota, FL 34231
Application Measuring screw with plate for free travel on brake band piston B1.
Model 722.4
KK70-A
Application Complete set of ball bearing extractors for 6000-6013, 6200-621, 6300-6311 and 6403-6408 type bearings. Replaces #000-9933 and #116-0733. Replacement arms available.
Model All
KK17-K
Application Special reinforced bearing separator and drive cross member for removing bearing inner race from the drive flange on rear wheel bearing. From Kukko of Germany.
Model All
KK20-10
Application Model All This 2 arm sliding jaw puller is ideal for transmission and differential gears, ball bearings and tapered roller bearings. For applications requiring longer arms see #KK1-250-P for extra long arms (250mm long).
KK1-250-P
Application 250mm extension arms, compatible with all 20 and 30 series Kukko pullers
Model All
KK21
Application Model Large range of internal extractors for use with #KK22-1 and All KK22-2. Sizes range from 5mm to 100mm in diameter.
Page #38
Sarasota, FL 34231
Application Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)
Model All
KK22-2
Application Large counter stay for use with Kukko extractor #KK21-3 thru #KK21-8.
Model All
32-Suspension 924-0231
Model W116, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 211
1117J
Application Compresses all types of Macpherson style coil springs front and rear. Includes three sets of jaws (2) for 110, 120 and 130mm springs found in most Mercedes.
Model W163, 164, 171, 210, 211, 219, 230, 245, 251
1117V
Application This vice adapter holds the Macpherson strut when off the vehicle.
Model All
Page #39
Sarasota, FL 34231
Application Model Use to remove the top seal on the front Airmatic suspension W220 strut.
900-0007
Application Model W220 Use to remove and install the residual pressure valve on front-axle air suspension strut (Airmatic). Double sided tool. 1/4" drive. See #211-0009 for E class. Replaces #220-0009.
203-0007
Tool Name Application SUSPENSION STRUT Pin wrench socket for the removal of the suspension strut SOCKET retainer nut.
Model W203
211-0009
Application Use to remove and install air suspension line screw joints.
211-0763
Tool Name Application EMERGENCY Use to move vehicle when Airmatic system is disabled BUMBERS FRONT & during repair. REAR
221-0031
Application Use to move vehicle when Airmatic system is disabled during repair.
Model W221
Page #40
Sarasota, FL 34231
Application Torsion bar savers allow replacement of the torsion bar ends with torsion bar still in place in the vehicle.
KK129-0
Application Model All Scissor type puller allows access to difficult to reach and obstructed ball joints. 2-stage action allows removal of spindles up to 50mm in length. Mfg. by Kukko of Germany.
ST20-17x19
Application 17X19mm - Use with #H2594 to adjust shock absorber damper tension. Special deep offset box end wrenches. Use to adjust shock absorber retainer nuts.
Model All
116-0462
Application Model Presses the ball joint into steering knuckle while the knuckle W116, 123, 126 is in place on the car.
124-0543
Application Model Puller and installer tool for angular ball bearing from steering W124.2, 124.3 knuckle. (4MATIC)
Page #41
Sarasota, FL 34231
Application Puller and installation tool for rubber mounts-lower wishbone. Also see #B129-0043.
220-0061
Application Model Use to remove the top seal on the front Airmatic suspension W220 strut.
B129-0343
Application Use to Remove and install lower ball joint support on the wishbone. Replaces #107-0143.
B140-1143
Tool Name Application BEARING RACE AND Installs bearing outer race and radial seal ring of front axle SEAL RING hub. INSTALLER
Model W140
B202-0143
Tool Name LOWER CONTROL ARM BUSHING KIT FRONT & REAR W202
Application Removal and installation tool for rear rubber mount on the lower wishbone for W170 and W202 chassis. Also installs front mount on W208 chassis.
B210-0043
Tool Name LOWER CONTROL ARM BUSHING KIT FRONT & REAR W210
Application Puller and installation tool for rubber mount front & rear lower wishbone mount.
Model W210
Page #42
Sarasota, FL 34231
Application Use to install the ball joint into the steering knuckle on late model S, E, CLK, CLS and SL class.
B220-0643
Application Use to replace the sub frame bushings on the torque strut control rods.
385-0007
Application
Use to remove and install the retaining nut on the supporting joint of the bottom wishbone in the front and rear axle.
Model W163
KK128-2
Tool Name Application TIE ROD BALL JOINT Puller for separating tie rod and steering knuckle ball joints PULLER - 23-32mm without tearing ball joint boots. Mfg. by Kukko of Germany.
Model All
KK129-0
Application Model All Scissor type puller allows access to difficult to reach and obstructed ball joints. 2-stage action allows removal of spindles up to 50mm in length. Mfg. by Kukko of Germany.
Page #43
Sarasota, FL 34231
Tool Name Application UNIVERSAL Hydraulically driven, this kit quickly pushes the axle out of HYDRAULIC AXLE the hub, and removes the hub. Pump not included AND SLIDE HAMMER EXTRACTOR
Model All
B90K
Tool Name Application Model WHEEL BEARING KIT Use to remove and install wheel bearings on out of the hub All on the car
B140-0333
Application Use to remove and install the front and rear rubber sub frame mount on the rear axle carrier.
B201-1143
Tool Name REAR AXLE CARRIER MOUNT REMOVER & INSTALLER KIT
Application Model Puller and installation tool for front and rear rubber mount W124, 129, from rear axle carrier. See #202-0343 for 170, 202, and 208 201 chassis.
B210-0243
Application Model Use to remove and install rubber differential mount bushings W210 in the center of rear axle assembly.
966-0043
Application Use to remove and install the rear differential mount bushings.
Page #44
Sarasota, FL 34231
Application Puller and installer tool for wheel bearing in wheel carrier and installation of rear axle shaft flange.
Model W124, 129, 163, 170, 201, 202, 203, 208, 209, 210.
201-0009
Tool Name Application PINION FLANGE Pinion joint flange 12 point socket. Use to remove special SOCKET - 27mm 3/4" retaining nut in late model cars. DRIVE
111-0507
385-0007
Application
Use to remove and install the retaining nut on the supporting joint of the bottom wishbone in the front and rear axle.
Model W163
915-0107
Tool Name Application Model REAR AXLE FLANGE Differential drive pinion flange groove nut socket for use on W107, 114, GROOVE NUT models with constant velocity joint axels. 115, 116, 123 SOCKET
915-0207
Page #45
Sarasota, FL 34231
Application Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)
Model W107, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220
KK21
Application Model Large range of internal extractors for use with #KK22-1 and All KK22-2. Sizes range from 5mm to 100mm in diameter.
KK22-1
Application Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)
Model All
KK22-2
Application Large counter stay for use with Kukko extractor #KK21-3 thru #KK21-8.
Model All
KO4012M-14
Tool Name Application OIL DRAIN HEX Short body allows easy removal of oil, differential and HEAD SOCKET 14mm transmission drain plugs. 1/2" DRIVE
Model All
ST3004
Tool Name Application Model W215, 220 HEX HEAD SOCKET XZN Hex Head Socket-12mm x 55mm 1/2" drive with 12mm XZN X 55mm special short format for rear axle spring link. (119-589-0010) 1/2"DR.
Page #46
Sarasota, FL 34231
Application 12 point 1/2" DR. with thin walls and deep broaching for collar nut on drive flange.
Model W107, 123, 124, 126, 129, 140, 168, 170, 201, 202, 208, 210, 463
Tool Name Application WHEEL ALIGNMENT Use in place of 2 lug bolts to hold wheel in place while GUIDES installing other lug bolts 12X1.5mm
M0030A
Tool Name Application WHEEL ALIGNMENT Use in place of 2 lug bolts to hold wheel in place while GUIDES installing other lug bolts 14X1.5mm.
MBWHEELKIT
Application Special Decagon (10 sided) sockets for removal of triplet aluminum alloy steel ring on special SL wheels.
Model W230
341C
Application Model Universal toe-in gauge allows quick and easy adjustment of All front end toe without the use of a lift.
Page #47
Sarasota, FL 34231
Application Special tool for the removal and installation of wheel weights.
Model All
B2309KIT
Model All
Tool Name Application VERY THIN WRENCH Use to remove driveshaft lock nuts. - 41mm
Model 107, 108, 109, 111, 113, 114, 115, 116, 123, 126, 201
T9A-46
Tool Name Application Model VERY THIN WRENCH Use to remove driveshaft lock nuts. See # T9A-41 Also see 107, 108, 109, - 46mm #T9A-SET. 111, 113, 114, 115, 116, 123, 126
T9A-SET
Tool Name Application Model VERY THIN WRENCH Set of 6 very thin wrenches for use in a variety of situations. All SET Sizes 24mm, 27mm, 32mm, 36mm, 42mm, 46mm
Page #48
Sarasota, FL 34231
Application Model All This 2 arm sliding jaw puller is ideal for transmission and differential gears, ball bearings and tapered roller bearings. For applications requiring longer arms see #KK1-250-P for extra long arms (250mm long).
KK1-250-P
Application Model All PULLER ARMS - 250mm LONG (2)Extra long arms for puller #KK20-10 allows removal of bearings and gears from long shafts, such as reverse and 5th gear.
42-Brakes 000-3523
Tool Name BRAKE PISTON ANGLE GAUGE - 20 DEGREE 38mm & 35mm
Application Use to set the brake piston angle on 35mm & 38mm diameter pistons.
Model W107, 114, 115, 116, 123, 124, 126, 129, 140, 201, 202
112-0961
Model All
116-0162
Model All
Page #49
Sarasota, FL 34231
Application Model Use to remove and install brake shoe check spring on glued Most or riveted brakes. Moveable claw locks in any position desired.
KK126-00
Application Use to press calipers back into assembly for easy installation of pads.
Model All
KK126-01
Model All
KK126-02
Application Model Use to hold the brake piston/caliper assembly with the brake All hose attached during assembly or removal.
KK126-03
Model All
ST12373
Application Wire brush for cleaning of fixed brake calipers and shoes.
Model All
Page #50
Sarasota, FL 34231
Tool Name Application Use for SBC hydraulic lines. CROWFOOT SOCKET - 14mm 3/8" DRIVE
46-Steering B900-0059K
Tool Name Application IGNITION AND DASH Kit includes early and late model ignition switch cover KIT grippers, retainer nut socket (6/97 and newer), ignition lock release pins, dash removal hooks and radio release keys.
Model W126, 129, 140, 163, 170, 202, 210, 211, 220, 230, 240, 414, 463
900-0059
Application Model Wires allow depression of lock retainers for easy removal of W126, 124, ignition switch. Use with tool # 126-0714 or #202-0014 129, 140, 201, 210
900-0059K
Application Ignition Lock Removal Pins - 124, 126, 201, Dash Hooks -107, 116, 123, 124, 126, 140, 201, Radio Removal Keys 129, 140, 202, 210.
210-0007
Application Special socket for removal of ignition lock cover. Replaces Mercedes #129 589 00 007 00.
Model W129, 140, 164, 169, 171, 199, 202, 203, 208, 209, 210, 211, 215, 219, 220, 221, 230, 240, 245, 251, 414
Page #51
Sarasota, FL 34231
Tool Name Application IGNITION LOCK Use to aid in removal and installation of the ignition lock REMOVING SLEEVE cover. Also see #210-0007
126-0714
Application Rubberized interior allows easy turning of inner lock cover particularly on W126-and 124 chassis. Use with tool # 900-0059.
ST1445
Application Special bit for R&R of screws on airbag control units and sensor mounts.
ST1295
Model All
116-0621
Tool Name Application STEERING POSITION Use to center steering gear for correct positioning of CHECK SCREW steering wheel during installation.
201-0621
Tool Name Application STEERING POSITION Use to center steering gear for correct positioning of CHECK SCREW steering wheel during installation.
Page #52
Sarasota, FL 34231
Tool Name Application STEERING POSITION Use to center steering gear for correct positioning of CHECK SCREW steering wheel during installation.
202-0133
Tool Name Application Model DRAG LINK PULLER Use to remove drag link ball joint. Use with pad #129-1063. W202
KK128-2
Tool Name Application TIE ROD BALL JOINT Puller for separating tie rod and steering knuckle ball joints PULLER - 23-32mm without tearing ball joint boots. Mfg. by Kukko of Germany.
Model All
KK129-0
Application Model All Scissor type puller allows access to difficult to reach and obstructed ball joints. 2-stage action allows removal of spindles up to 50mm in length. Mfg. by Kukko of Germany.
KK204-1
Application Heavy duty puller with reinforcing cross member for removing pitman arms and drag link arms.
Model All
Page #53
Sarasota, FL 34231
Application Allows quick release of fuel pipe connections (quick couplers), particularly the fuel pump connection to delivery sensor unit.
202-0007
Model W202
203-0107
Tool Name Application FUEL TANK SENDER Use to remove and install the locking ring of the fuel tank SPIDER WRENCH delivery sensor unit.
210-0107
Tool Name Application FUEL TANK SENDER Pin wrench for removing and installing lever-type fuel level PIN WRENCH - 5mm sensor.
M0035A
Tool Name Application GAS TANK SOCKET - Use to remove fuel tank filter body and fuel gauge sending 46mm units.
Model All
202-0190
Model W202
Page #54
Sarasota, FL 34231
Tool Name Application IGNITION AND DASH Kit includes early and late model ignition switch cover KIT grippers, retainer nut socket (6/97 and newer), ignition lock release pins, dash removal hooks and radio release keys.
Model W126, 129, 140, 163, 170, 202, 210, 211, 220, 230, 240, 414, 463
110-0059
Model W107, 108, 109, 111, 114, 115, 116, 123, 125
140-0233
Model W124, 126, 129, 140, 168, 170, 201, 202, 208, 210, 463
129-0109
Application Model Use to remove and install socket bulbs in instrument cluster W129, 140, without having to remove complete instrument cluster. 163, 170, 202, 208, 210, 220
140-0133
B1630
Tool Name Application Model RESISTANCE Resistance substitution box allows testing and calibration of All SUBSTITUTION BOX dash gauges, injection system sensors, cruise control, and anti theft systems. (#124-0963)
Page #55
Sarasota, FL 34231
Application Model Closed-circuit current test adapter 1 for testing closed-circuit R129 as of current consumption of electric circuit 1.9.95, W140, 163, 168, 170, 202, 208, 210, 220
140-1321
Application For checking closed-circuit current consumption of electric circuit (for maxi-flat pin fuses).
Model R129 as of 1.9.95, W140, 163, 168, 171, 202, 208, 210, 220
ST1520
Application Model Includes: Round contact pin extractor 1.5mm & 2.5mm, Flat All plug contact removers for 2.8mm, 2-prong contacts 5.8mm, 1.6mm Micro-Timer II and !II, 9.5mm Maxi-Power Timer, 5.5, 8,5mm and twin secondary lock device and E-95 extractor.
Application Use to safely probe out different plug components and control units.
Model All
B1630
Tool Name Application Model RESISTANCE Resistance substitution box allows testing and calibration of All SUBSTITUTION BOX dash gauges, injection system sensors, cruise control, and anti theft systems. (#124-0963)
Page #56
Sarasota, FL 34231
Tool Name Application IGNITION AND DASH Kit includes early and late model ignition switch cover KIT grippers, retainer nut socket (6/97 and newer), ignition lock release pins, dash removal hooks and radio release keys.
Model W126, 129, 140, 163, 170, 202, 210, 211, 220, 230, 240, 414, 463
B9059M
Application Contains all tools needed to remove models from 1990 to the present.
Model All
900-0059K
Application Ignition Lock Removal Pins - 124, 126, 201, Dash Hooks -107, 116, 123, 124, 126, 140, 201, Radio Removal Keys 129, 140, 202, 210.
963-0105
V8695
Tool Name
Application Model This tool is equipped with the same connector and is of the All with airbags SRS TEST RESISTOR same resistance as the air bag module. Use to test for faulty airbags.
611250
Application Model Allows easy removal of BOSCH relays in even the tightest All locations.
Page #57
Sarasota, FL 34231
Tool Name Application REMOVAL PLATE (2 Use for removal of radio Also part of #B9059M PIECES)
Model R129
126-0007
Tool Name Application ANTENNA SPANNER Antenna mast mounting nut. WRENCH
B57BG-E
Application This kit includes the basic crimper and 3 interchangeable crimping heads.
Model All
B57BG-M
Tool Name Application WIRE TERMINAL This kit includes the basic crimper and 5 interchangeable AND CONNECTOR crimping heads, plus a wire stripper. CRIMPING - MASTER KIT
Model All
KK43-2
Application Small puller for use on battery terminals, small gears and bearings.
Model All
ST1520
Application Model Includes: Round contact pin extractor 1.5mm & 2.5mm, Flat All plug contact removers for 2.8mm, 2-prong contacts 5.8mm, 1.6mm Micro-Timer II and !II, 9.5mm Maxi-Power Timer, 5.5, 8,5mm and twin secondary lock device and E-95 extractor. Page #58 Sarasota, FL 34231
Application Used to remove and install screw plug on condenser fluid CONDENSOR FLUID reservoir. RESERVOIR SOCKET
ST440-14
Tool Name Application Use to access hard to reach A/C expansion valves. CROWFOOT LINE WRENCH - 14mm 3/8" DRIVE
Model M107, 123, 124, 126, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463
ST440-17
Tool Name Application Use to access hard to reach A/C expansion valves. CROWFOOT LINE WRENCH - 17mm 3/8" DRIVE
Model M107, 123, 124, 126, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463
ST440-19
Tool Name Application Use to access hard to reach A/C expansion valves. CROWFOOT LINE WRENCH - 19mm 3/8" DRIVE
Model M107, 123, 124, 126, 129, 140, 170, 201, 202, 203, 210, 215,
ST440-22
Tool Name Application Use to access hard to reach A/C expansion valves. CROWFOOT LINE WRENCH - 22mm 3/8" DRIVE
Model M107, 123, 124, 126, 129, 140, 170, 201, 202, 203, 210, 215,
ST440-24
Tool Name Application Use to access hard to reach A/C expansion valves. CROWFOOT LINE WRENCH - 24mm 3/8" DRIVE
Model M107, 123, 124, 126, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463 Sarasota, FL 34231
Page #59
Application Use for various assembly/disassembly jobs, such as, removing clipped panels and covers
B2014
Tool Name Application PANEL POPPER KIT Set of 4 panel poppers for removing panels and trim on all types of vehicles.
Model All
B277-477
Application Use to remove wood and plastic trim pieces, door panels and dashboard without damage.
Model All
AS4750
Model All
28DBC
Application Model All Ideal for pulling threaded studs with a heavy duty impact wrench. Kit includes: bolt, sleeve and 14 collets Collet sizes include: 6x1.0, 7x1.0, 8x1.0 ,8x1.25, 9x1.0, 9x1.25, 10x1.25, 10x1.50, 12x1.25, 12x1.50, 14x1.50, 14x2.0, 16x1.5, 16x2.0mm.
H2715-20H5
Model All
Page #60
Sarasota, FL 34231
Tool Name Application Model VERY THIN WRENCH Set of 6 very thin wrenches for use in a variety of situations. All SET Sizes 24mm, 27mm, 32mm, 36mm, 42mm, 46mm
D-Diagnostics SDS-COMPACT4
Tool Name Application Model STAR DIAGNOSTIC Mercedes factory diagnostic system. Includes DAS and WIS All from 1988 to SYSTEM - COMPACT systems. current 4
DS2020
Application Model Complete Mercedes Benz Scan Tool is a multi use scanner Call for current covering ECM, PCM, ABS, SRS, HVAC, Immobilizer, coverage Instrument cluster and more for a variety of vehicle makes. Supports activation, basic setting reset, Fault codes, plus multimeter and lab scope
DS2021
Application Model Complete Mercedes Benz Scan Tool is a multi use scanner Call for current covering ECM, PCM, ABS, SRS, HVAC, Immobilizer, coverage Instrument cluster and more for a variety of vehicle makes. Supports activation, basic setting reset, Fault codes.
OBD2-500
Tool Name Application Model OBD-II / EOBD FAULT All models 1996 Quick scan reads and resets OBD-II and EOBD fault codes CODE READER - Current live data, freeze frame, ands all SAE OBD-II modes 1 thru 9. SAE1850, ISO and CAN protocols. Comes with instruction manual with over 2000 mfg. fault code definitions.
Page #61
Sarasota, FL 34231
Tool Name Application Model OBD-II / EOBD FAULT Quick scan reads and resets OBD-II and EOBD fault codes. All models 1996 CODE READER Comes with instruction manual with over 2000 fault code - Current definitions.
DBL800
Application Model Microprocessor controlled charger/power supply to maintain All Models power levels during programming and diagnostics. Microprocessor controlled charging, measuring and monitoring. Built-in interface for computer, programming unit, printer and large display. Mercede
B70A
Application Provides "clean" power for reprogramming and coding. Maintains stable battery voltage from 13.6 to 14.4 volts.
Model All
OBD2-BOB
Application This J1962 break out box allows access to all wires in the OBD-II Diagnostic Interface This makes it easy to trace CAN Bus faults, Power supply problems and track failed diagnostic controllers.
38PINBOB
Application Model Allows easy access to the 38-pin diagnostic socket when W129, 140, using scanners DS2020, DS2021 or with a standard DMM. 170, 202, 203, 208, 210, 220
B140-1463A
Application Extension cable allows use of test equipment while driving or on dynamometer.
Page #62
Sarasota, FL 34231
Tool Name Application Model RESISTANCE Resistance substitution box allows testing and calibration of All SUBSTITUTION BOX dash gauges, injection system sensors, cruise control, and anti theft systems. (#124-0963)
BT7205J
Application Model All The Terminator is a superior Logic probe combining the features of a DMM and oscilloscope but simplifying the display for technicians that want to find the pulse but don't need the to see the trace. Particularly useful for tracing CAN signals.
102-0463
Application Tests CIS-E electronic idle speed control with standard multimeter. (VOM-DMM)
CODEBRAKER
Application Model The Code Breaker is the only publication available with All Models from more than 2700 fault code numbers with detailed description 1996 to the and repair suggestions all lined up in an easy to reference present. format.
K-Kablex ST1520
Application Model Includes: Round contact pin extractor 1.5mm & 2.5mm, Flat All plug contact removers for 2.8mm, 2-prong contacts 5.8mm, 1.6mm Micro-Timer II and !II, 9.5mm Maxi-Power Timer, 5.5, 8,5mm and twin secondary lock device and E-95 extractor.
Page #63
Sarasota, FL 34231
Application
Use to remove the round contacts with locking feathers. Replaceable tips available as #ST1511. Also in kit #ST1550.
Model All
ST1504/1514
Application
Use to remove the round contacts with locking feathers. Replaceable tips available as #ST1514. Also in kit #ST1550.
Model All
ST1553
Tool Name Application Model CONTACT Use to remove double size flat contacts with single release All EXTRACTOR (FLAT) - channel. 2.8, 5.8mm
ST1584
Tool Name Application Model All CONTACT Use to release round soldered terminals from sockets. EXTRACTOR Center channel allows easy routing of wire without damage. (ROUND SOLDERED) - 4.0mm
ST1585
Tool Name Application Model All CONTACT Use to release round soldered terminals from sockets. EXTRACTOR Center channel allows easy routing of wire without damage. (ROUND SOLDERED) - 2.5mm
ST1586
Tool Name Application CABLE CONNECTOR Use to release secondary locking devices of relay panels EXTRACTOR and junction boxes on DaimlerChrysler models. LARGE TWIN
Model All
Page #64
Sarasota, FL 34231
Tool Name Application CONTACT DBGM, for flat plug-in sockets using E-95 contacts. EXTRACTOR (FLAT) - (#210-0133) E-95
Model All
ST1588
Application Model Use to remove the Grote Hartmann GSK-Flat Fuse Contacts All (1-, 2-, 3 terminal version; 2, 4 and 6 locking tongues). (#202-0333)
ST1591
Application Use to remove flat plug-in sockets in terminals with two release channels. (#210-0233)
Model All
Page #65
Sarasota, FL 34231
Table of Contents
0
Alphabetized Listing
15 49 30 9 3 3 1-3 4-7 7-13 14-18 18-23 9 17, 63 24 28 3 9 26 4 55 5 27 8 31, 45 5 6 11 39 39 4 25 35 4 49 9 28 28 31 12 11 4 49 41 52 11 10 10 1 11 3 5 17 28 26 26 11 41, 45 48 58
000-3323 000-3523 000-4731 000-5843 001-0016/2 001-0016/9 01-General Engine 03-Cylinder Crankcase 05-Cylinder Head, Engine Timing 07-Injection System 09-Diesel 102-0421 102-0463 103-0037 103-0040 103-0114 103-0163 103-0209 110-0040 110-0059 110-0761 111-0034 111-0315 111-0507 111-0843 111-1231 111-1861 1117J 1117V 112-0040 112-0109 112-0161 112-0340 112-0961 112-0963 113-0001 113-0040 115-0723 116-0043 116-0101 116-0140 116-0162 116-0462 116-0621 116-0663 116-2033 116-2033P 117-0223 119-0001 119-0014 119-0114 119-0463 120-0201 120-0621 120-0721 123-0361 124-0543 124-1763 126-0007
126-0143 126-0314 126-0414 126-0431 126-0621 126-0714 126-1014 129-0005 129-0109 129-0623 1318/10 1318/4 1318/5 1318/6 1318/8 1318K 1318KIT 1318-R 137-0140 13-V Belt 140-0014 140-0133 140-0233 140-1221 140-1321 140-1521 15-Ingition 163-0037 168-0121 18-Lubrication 201-0009 201-0114 201-0214 201-0359 201-0621 201-0721 201-0821 201-1243 202-0007 202-0014 202-0133 202-0190 203-0007 203-0010 203-0107 208-0021 20-Engine Cooling 210-0007 210-0107 211-0009 211-0763 220-0061 220-0343 221-0031 230-0040 25-Clutch & Pedal Linkage 26-Manual Transmission 27-Automatic Transmission 285-0040 285-0140
Table of Contents
2 3
Alphabetized Listing
4 60 39-41 41-43 47 44-47 43, 45 62 47-48 48-49 49-51 51-53 54 55-56 21 5 21 22 19 5 29 27 22 57 12 12 20 21 27 25 25 15 56-58 59 40 51 51, 57 12, 24, 28 22 20 19 31, 35, 45 45 10 35 35 3 22 20 10 39 22 57
285-0240 28DBC 32-Suspension 33-Front Axle 341C 35-Rear Axle 385-0007 38PINBOB 40-Wheels and Tires 41-Drive Shaft 42-Brakes 46-Steering 47-Fuel Supply 54-Instrument Cluster 601-0008 601-0240 601-0514 601-0521 602-0033 602-0040 603-0040 604-0034 606-0009 611250 615-0001 615-0003 615-0007 617-0821 642-0009 66US-16 66US-21 691STE 82-Electrical Equipment 83-Heating & Air Conditioning 900-0007 900-0059 900-0059K 900-0307 900-8673 901-0053 902-0033B 915-0107 915-0207 915-0734 915-0807 916-0011 916-0013 916-0021 917-0053 917-0623 924-0231 936-0223 963-0105
966-0043 966-5843 986-1107 A0201 A0202 A020201 A020202 A020204 A020206 AS4750 AS4765 AS4955
5 6
8 9
B1027 B103-0037 B110-0101 B111-0315KIT B112-0001K B113-0001 B116-0134 B117-0207 B129-0343 B140-0333 B140-1143 B140-1343 B140-1463A B1407 B1594 B1630 B1924 B201-1143 B2014 B202-0143 B210-0043 B210-0243 B220/163 B220-0643 B2309KIT B234MASTER B271-0140 B277-477 B3676 B3677 B57BG-E B57BG-M B606-0053 B606-0053KIT B611-0033LONG B611-0033PLUS B611-0421 B667-0363 B6700 B6700ADJ B70A B7200 B722-0315 B900-0059K B900-0199 B9042 B9059M
Table of Contents
B
Alphabetized Listing
44 34 60-61 19 19 63 31 63 62 61-63 61 61 30 30 60 30 23 50 1 33, 38, 49 50 50 50 50 43, 53 41, 43, 53 32, 38 32, 38, 49 53 32, 38, 46 6 6, 33, 39, 46 33, 39, 46 58 32, 38 63-65 6, 32 6, 27, 46 23 47 47 18, 54 8 8 9 11 21 16 21 13 13 13 13
C D
B90K B9336A B-Body - General BCDIINJPLUS BINJSEATCUT BT7205J C-26 CODEBRAKER DBL800 D-Diagnostics DS2020 DS2021 FZ19 FZ20 H2715-20H5 H2740 H4550 H797 H992LG-T55 KK1-250-P KK126-00 KK126-01 KK126-02 KK126-03 KK128-2 KK129-0 KK17-K KK20-10 KK204-1 KK21 KK21-0 KK22-1 KK22-2 KK43-2 KK70-A K-Kablex KO4012M KO4012M-14 KO4133 M0030 M0030A M0035A M0037 M0037-104 M0037-119 M1160 M24D M501 M502 M70TE M70TE/1 M70TE/1A M70TE/2
O Q S
M70TE/2A M70TE/X MBWHEELKIT OBD2-309 OBD2-500 OBD2-BOB QP1000 SDS-COMPACT4 ST1009DC ST10507KK-3 ST1054-10 ST1054-5 ST1054TXT55 ST10623/1 ST10627 ST11063 ST11085 ST12373 ST12506 ST1295 ST12975 ST1445 ST1501/1511 ST1504/1514 ST1520 ST1553 ST1584 ST1585 ST1586 ST1587 ST1588 ST1591 ST20-17x19 ST3000 ST3004 ST3047-12 ST3049-8 ST3054/8L ST3054XM10 ST3054XM12 ST3054X-M8 ST3149-8 ST440-14 ST440-17 ST440-19 ST440-22 ST440-24 ST51-27 ST51-30 T13-22 T9A-41 T9A-46 T9A-SET TS1015 TS10155
F H
Table of Contents
U V
Alphabetized Listing
23 57 7 12