Professional Documents
Culture Documents
7. 8. 9. 10.
This is exact string for dummies what should be in your .reg file. SAVE ! Install this file to your system, double click. Go to browser setting, clean cacheclose. Now you can start your vm, open it in browser and it should opens your consoles with Putty when you click on active diagram device.
4. Now you can start your lab. It will load with all initial configs. BTW if you do not use point 3. All configs what you did will be kept in NVRAMs even you shutdown vm. Nice, isnt it? You use your lab from point where you stopped in previous day
Written by UldisD
4. Press Choose file find your downloaded lab, press import 5. Check boxes Select all labs and Select all initial config packs, in the Folder meny choose where your lab will stored.
6. Press Import Labs 7. Go to tab Laboratories choose imported lab, press edit mode of this lab, small brown book right side
8. Scroll down till section devices. In the menu Apply an Initial Config Pack to all device: choose config pack for this lab. 9. In the menus for each device choose correct IOS, for switches L2 for routers L3. 10. Press Save
Written by UldisD
Written by UldisD
7. Now your IOS is uploaded. Lets got to use it in lab. Go to tab Laboratories choose lab what IOS have to be changed, press edit mode of this lab, small brown book right side
8. Scroll down till section Devices. Column IOS: Use menu against each device and choose other IOS, or new uploaded IOS. When done for all, press Save DO NOT MESS L3 IOS for L2 devices or vice versa!
Written by UldisD
9. IMPORTANT! After this action do the section: Steps, If you want to start TS lab from scratch with faults!!!
Steps, how to change initial config pack if there are more than one
10. Go to tab Laboratories choose imported lab, press edit mode of this lab, small brown book right side
11. Scroll down till section devices. In the menu Apply an Initial Config Pack to all device: choose OTHER config pack for this lab. This config pack should match this lab. You cannot import any other config pack and try to add it to your lab. 100% lab will be screwed then, if those wasnt created on same lab topology.
12. Press Save 13. Go to tab Laboratories and click on this lab INE TS here
14. IMORTANT! Go to Tab devices, and press actions sixth button from left, looks like trash, for All devices. This wil clean previous configs from NVRAMs, but not delete initial configs. Press Trash named Stop all devices and wipe and all configurations
Written by UldisD
15. DONE, now you can start your lab with new applied initial config pack.
Press it. 4. It will erase all previously saved configs in NVRAMS and vlan.dat. This command will NOT erase my preconfigs from labs. Start devices. All should work.
Written by UldisD
1xNM-4E and 2xNM-4T in sh run looks like: e0/0-0/3, s1/0-1/3, s2/0-2/3 1xNM-4E and 1xNM-4T in sh run looks like: e0/0-0/3, s1/0-1/3 1xNM-4E and 0xNM-4T in sh run looks like: e0/0-0/3 0xNM-4E and 2xNM-4T in sh run looks like: s0/0-0/3, s1/0-1/3 Last example if Ethernet cards are 0 then Serial will place first slot and will start from 0/x For switches you should add Ethernet cards only, Serial is 0. 4x1xNM-4E and 0xNM-4T in sh run looks like: e0/0-0/3, e1/0-1/3, e2/0-2/3, e2/0-2/3 Use 0 in Ethernet card fields are necessaryif you will leave it empty, it will add 8 NM cards to your device. Lets say we want to create lab: a) R1 e0/0 con to R2 e0/0; b) R1 s1/0 con to R3 s0/0 (here you can see that R3 has no Ethernet NM at all, therefore Ethernet field is 0) c) R1 e0/1 con to SW1 e0/0 d) R2 e0/1 con to SW1 e0/1 Syntax for this lab will be: 1:0/0 2:0/0 1:1/0 3:0/0 1:0/2 4:0/0 2:0/1 4:0/1 No press ADD and NEW additional fields will opens: 7. Now You can see section named Devices, a) As first is menu Apply an Initial Config Pack to all device this will be used later when we create it. b) Here we will add device NAME, choose correct IOS and add interfaces for each of device. Continue lab first device is R1, second is R2, third R3 and forth is SW. Fill these names in the fields. c) In IOS drop-down menu choose your favorite L3 or L2 IOS for particular device. d) Fill RAM and NVRAM, I recommend for 15.x series IOS use 256 RAM and 64 for NVRAM e) And now very important point, add interfaces for each device. As I wrote in p. 6. If you will add 1 as Ethernet you get 4 Ethernet in device, if add 2 you have 8 Ethernet. Same with serials. If you dont need any of type just say 0. Do not leave empty, it will add 8 NMs by default to your device. f) Continue our test LAB, for R1 we need 2 Eth connections and 1 Ser, fill fields 1 and 1, for R2 needs eth only, fill 1 and 0, for R3 needs serial only 0 and 1, SW need 2 Ethernet connections and we have enough with 1 eth and 0 serial. g) Next two checkboxes, do not check L2 keepalive if you use router-switch combinations in lab, this works with switch labs only. Next watchdog I check always. h) Drop-down menu picture you can choose what device icon you want to see, router or switch, FR switch i) Boot delay is advanced option and you can add time in seconds when this device start to boot after mass start, if R1 boot delay is 20, thats mean that all devices start immediately after press start, but R1 will start boot after 20 sec. You can leave this field empty.
Written by UldisD
j) Initial config menu will be used later when you get your config pack. 8. Next section is Pictures also is useful. You can upload your own drawn pictures in .png format. I use visio for creating pictures then convert to .png and upload to iou-web. If you have already uploaded pic, just check box for pic what you want to see for lab.
Written by UldisD
10. Now, go to LAB edit mode (small book on the right side beside trash) on the section devices menu Apply an Initial Config Pack to all device choose your created config pack with given names, example: INE RS BGP Initial. Save. 11. Then in tab Devices use mass action button "stop all devices and wipe all configurations" (like trash). Now your created lab INE RS will start with your config pack. Additional: 12. After some requests, if you want to inject own faults into existing config pack is easy: a) Go to tab Laboratories, choose CONFIG (grey icon, usually under lab icon) what should be corrected, against it use small icon (books) to edit mode.
b) Do the necessary changes on each of device or couple of them. Each time after change in one device press Save c) Here, for the switches you can change the vtp mode, set vtp password, add vlans. Use Server mode only with added vlans. Client mode doesnt accept vlans.
Written by UldisD
5. Done, timers started. On the right upper web face part you will see timer.
6. Do switch off timer, change minutes to 0 7. Please understand that timer option is in the test way.
Advanced IOU WEB LAB tuning to use own picture as active diagram.
8. Upload your picture in .png format to iou web. 9. Go to LAB edit mode and check box of this picture for lab. 10. Pictures also have edit mode, find your picture which you want to tune as active workdesk and press edit (small book on right side) 11. You are in the edit mode of PIC. Name of pic you can change or leave as it. 12. You can add additional info for picture, but it is not needed. 13. IMPORTANT: Next field Map will be filled automatically and we will correct it little later. 14. IMPORTANT: Scroll down till you see your picture. NOW ATTENTION! Use your mouse and click one time on each device in the center. Follow the order click R1 then R2, R3, R4SW1FR. IN THE middle of icon. Do not click anywherebecause each of clicks are saved in map field! After click on all devices scroll back to field MAP. 15. Now you see the lines with coordinates with each of your click. And if you followed order you know that firs device is R1second R2SW NOW all is what you need is correct manually console port for each device. (By default all are 2000). First line looks like <area shape='circle' coords='375,254,30' href='telnet://{{IP}}:2000'>. Just change console port to 2001 for R1, in the next line change to 2002. Save. If your console port are different use numbers what you have for each device.
Written by UldisD
16. Now you go to LAB edit mode and uncheck Display diagram box, because you have your own active diagram. Save. 17. Clear cache of your browser!!! Close browser, open itand your lab with new face should work
8. NAT mode you cloud will give IP from NAT pool of your vm. You can configure ip dhcp address on Ethernet connected to cloud. 9. Bridged mode is much better. You can connect your cloud and iou routers to your real LAN. In my case I have VM Network Adapter 2 bridged with my PC NIC, and router in IOU getting IP address from my LAN and real Router. 10. Using bridged interfaces you can connect GNS topology, ASA, IDS, and Juniper to iou web. Tested it works! 11. Dont forget that Network adapters on vm settings can be unchecked to start on boot. If you want to use them, check connect on start up, and connect.