This document provides instructions for testing the omicron distance relay using different procedures:
1. It describes how to test points manually or by entering values, and how to adjust test settings like fault current and timing.
2. Instructions are given for single point testing, one-time reach and timing tests, and checking hardware configuration.
3. Steps are outlined for entering system data, selecting test directions and zones, and configuring zone settings.
4. The document also covers testing sequences with multiple ramps, checking minimum pickup currents, testing impedance from single tests, and adjusting measurement views for state testing.
This document provides instructions for testing the omicron distance relay using different procedures:
1. It describes how to test points manually or by entering values, and how to adjust test settings like fault current and timing.
2. Instructions are given for single point testing, one-time reach and timing tests, and checking hardware configuration.
3. Steps are outlined for entering system data, selecting test directions and zones, and configuring zone settings.
4. The document also covers testing sequences with multiple ramps, checking minimum pickup currents, testing impedance from single tests, and adjusting measurement views for state testing.
This document provides instructions for testing the omicron distance relay using different procedures:
1. It describes how to test points manually or by entering values, and how to adjust test settings like fault current and timing.
2. Instructions are given for single point testing, one-time reach and timing tests, and checking hardware configuration.
3. Steps are outlined for entering system data, selecting test directions and zones, and configuring zone settings.
4. The document also covers testing sequences with multiple ramps, checking minimum pickup currents, testing impedance from single tests, and adjusting measurement views for state testing.
Normal distance: you can test point by point manual change
Advanced distance you can adjust ramp of testing points 1 / 14 U can make right click and test the point this menu will appear Or u can write the value here and test 2 / 14 Here u can adjust the setting for your test Prefault a!" fault current 3 / 14 Advanced distance #hot if u want to make one point test $heck : for %one reach & timing test Press parameter ' hardware configuration 4 / 14 Press general ( detail to check the connection Press test opject 5 / 14 )nter your system data * +,P * -ou can select the direction for your test 6 / 14 #elect %one setting .o add new %one click new then edit #elect the type of your char" .hen enter the setting 7 / 14 $lick default setting and adjust the current / 0A then click O1 8 / 14 Press se2uence and enter your re2uired ramps start & stop 3 step 9 / 14 RELAY MIN. PICKUP CURRENT OP)N A4+"4,#.AN$) #$5))N #elect setting and change the fault current 3 6o to shot screen #elect impedance 3 click single test 10 / 14 High set #tate se2 " ake the first state ((((( healthy 78"9 for 8 ph & :A for 8 ph time 0 sec " .he sec" state +5 / ;:+ and other phases healthy time 0 sec .he third state change the value for ,5 around H# value/0,n then test ust adjust measurement view start at state 8 & stop at trip 11 / 14 0 nd method cb trip <= 3 ,> #O.> enable must A$ #O.> pick delay/; sec" ,N?)$. one state : voltage for all phases & ;:A ,5 3 ,#/,./:
12 / 14 #O.> A4+" 4,#.AN$) 3 make 4,#.AN$) fun" )nable A$ #O.> 6o to setting screen and adjust pre fault time case A/;9:msec case @ /09: msec " And after this test impedance from shot screen and sheck #O.> A)4 $ase A : #O.> OP)5A.) $A#) @ : #O.> NO. OP)5A.) 13 / 14 4$ #O.> 6o to #)<U)N$)5 screen #tate ;: 78"9 + & : A for all phases #tate 0 : fault state: +5/;:+&+#/78"9& +./78"9 & ,5/9A& ,#/: & ,./: and change the time for state ; case A/89:msec case @ /B9: msec and apply Cve to A07 $@ $AO#) through @O from Omicron click here and select @O:; for state ; & state 0 14 / 14 .est the two cases and check #O.> A)4 $ase A : #O.> OP)5A.) $A#) @ : #O.> NO. OP)5A.) VTS (voltage transforer s!"erv#s#on ( #etting +res"/0: v & ,res" / ;"9 A by using 2uick cmc inject this values +5/+#/+./78"9 + AN4 @AAAN$)4 3 current / : for all phases 4ecrease the value of +r to B8"9 + the led for +.# will be appeared ,ncrease ,5 UP .O ;"9 A the led will be disappeared 3 for phase #&. repeat the above state 15 / 14 @locking function ,nject 8 states like this : ; ( healthy state vr/vs/vt /78"9 v & balanced 3 ,r/,s/,t /: & time /0 sec 0 ( drop the voltage of ph" 5 to ;:+ and remain the others phases like state ; time / 0 sec 8 ( increase the value of current ,r to 7A .he relay not trip