This document provides the design of a bored cast in-situ pile. It includes input parameters such as load factors, pile geometry, material properties, and design requirements. The pile is designed to resist factored axial and lateral loads. Reinforcement is designed for the portion from the cut-off level to the depth of fixity and below, to resist bending and axial stresses. 7 numbers of 25mm diameter bars are provided from the cut-off level to the depth of fixity. 7 numbers of 16mm diameter bars and no additional bars are provided below for tension resistance. Lateral ties of 8mm diameter are specified at 200mm centres.
Original Description:
Work sheet example for analysis & design of bearing piles with pile cap for pile group
This document provides the design of a bored cast in-situ pile. It includes input parameters such as load factors, pile geometry, material properties, and design requirements. The pile is designed to resist factored axial and lateral loads. Reinforcement is designed for the portion from the cut-off level to the depth of fixity and below, to resist bending and axial stresses. 7 numbers of 25mm diameter bars are provided from the cut-off level to the depth of fixity. 7 numbers of 16mm diameter bars and no additional bars are provided below for tension resistance. Lateral ties of 8mm diameter are specified at 200mm centres.
This document provides the design of a bored cast in-situ pile. It includes input parameters such as load factors, pile geometry, material properties, and design requirements. The pile is designed to resist factored axial and lateral loads. Reinforcement is designed for the portion from the cut-off level to the depth of fixity and below, to resist bending and axial stresses. 7 numbers of 25mm diameter bars are provided from the cut-off level to the depth of fixity. 7 numbers of 16mm diameter bars and no additional bars are provided below for tension resistance. Lateral ties of 8mm diameter are specified at 200mm centres.
HFL SCOUR DEPTH RBL L1 Input Data Load factor FL FL 1.5 Diameter of pile D D 500 mm Pile capacity in compression P P 740 kN Pile capacity in Tension T Tc 480 kN Pile capacity in Lateral H Hc 100 kN Grade of concrete fck fck 25 N/mm^2 Grade of steel fy fy 500 N/mm^2 Clear cover c c 60 mm Minimum % of steel required pt,min pt 0.4 % Diameter of circular tie reinforcement t t 8 mm Min. diameter main reinforcement 1 1 16 mm Max diameter of main reinforcement 2 2 25 mm Area of pile cross section Ac Ac 196349.5 mm^2 ( b is the equivalent side of a square) b 443.1 mm Length of pile below cut off level L1 20000 mm Depth of Fixity calculation (As per Appendix C, Cl. C-1.2) Coe. of stiffness K1 inkg/cm (From Table 1 of IS 2911, Part1) K1 0.26 kg/mm Length of pile above GL, L1 L1 0 Modulus of Elasticity of Conc. E = 5000fck Ec 25000 N/mm 254842.0 Moment of inertia of pile I = D 4 / 64 I 306796.2 cm Pile Stiffness T = (E I /K1 )^1/5 T 197.5 cm L1 / T = 0.00 L1/T 0 As Fixed head pile Lf / T (From Fig 2 of IS 2911, Part1 Sec.2) Lf/T 2.2 Length of Fixity Lf Lf 434.6 cm Design of pile from cut off level to depth of fixity Factored Lateral load Hu Hu 111 kN Factored Bending moment Mu = Hu(L1+Lf)/2 For fixed head pile Mu 241.2 kNm Reduction factor = 0.83 (From Fig 3 - IS 2911, Part 1 Sec.2) Rf 0.83 Design Bending moment Mu Mu(d) 200.2 kNm Effective cover d' d' 72.5 mm d' / D = d'/D 0.145 Design for Compression with Bending Slenderness ratio=(leff/D) Leff/D 10.43 <12 short col. Minimum eccentricity =(Lf/500)+(D/30) 25.36 mm 0.05D 25 mm Factored compressive load Pu Pu 1110 kN Pu/fck*D*D Pu/fck*D^2 0.1776 Mu/fckD^3 Mu/fck*D^3 0.064 Refer Chart 57 of SP:16 pt/fck 0.025 percentage of steel, pt pt 0.63 % Area of steel required Ast required Ast 1227.2 mm^2 Design for Bending only Factored compressive load Pu Pu 0 kN Pu/fckD2 = 0 Pu/fck*D^2 0 Mu/fckD^3 Mu/fck*D^3 0.064 Refer Chart 57 of SP:16 for pt/fck pt/fck 0.065 pt pt 1.625 Area of steel required Ast Ast 3190.7 mm Provide 7 Nos 25 dia 7 25 mm Ast provided Ast provided 3436 OK Design of pile below depth of fixity Vertical Compression Factored compressive load Pu = 1500 kN Pu 1110 kN Axial capacity Pa,u = 0.4 fck Ac Pa 1963.5 kN OK Vertical Uplift (Tension): Factored Tensile load Tu = Tu 0 kN Area of steel required Ast,req = Tu / 0.87 * fy Ast 0.0 mm^2 Provide 7 Nos 16 dia + 0 Nos 0 dia 7 16 mm Ast provided 1407 OK HENCE PROVIDE 7 No. - Y25 Dia REBARS TO A DEPTH OF 6250MM FROM CUT OFF LEVEL AND PROVIDE 7 No. - Y16 DIA. BARS FOR BALANCE DEPTH OF PILE. LATERAL TIES Diameter of Circular ties = 8 mm Spacing of the circular ties : least of the following : i). Diameter of pile = 500 mm ii) 16 1 = 256 mm iii) 300 mm = 300 mm Provide Y8 Dia @ 200mm c/c