CONTENT.
1. Summary 1
2. Design of Unit CW 06 2B
3. Design of Unit CW 02 ree)
4. Design of Unit CW 08 22-24
5. Design of Unit CWO1 28-31
6, Mullion ransom connection ana
7. Brackets and anchorage 35-42
8 Sealant contact depth 8
9. Adequacy of glass thickness 446
10, Reference documents 47-167‘SUMMARY
This report glves the structural calculations for the adequacy of profes , connections,
brackets and anchorage fo withstand. design loads for typical
wos & cwoe
lazing units CW 01 , owerDESIGN CODES USED
8S : 6399 : PART 2: 1997 - WIND LOADING
BS : 8118 : PART 1: 1991 - STRUCTURAL USE OF ALUMINIUM
BS : 5950 : PART 1 : 2000 - STRUCTURAL USE OF STEEL
INTENDED USE OF
‘STRUCTURE
GLAZING TO RC STRUCTURE
BASIC WIND SPEED
45. M/SEC (3 SEC WIND SPEED )
25.3 M/SEC (MEAN HOURLY WIND SPEED )
SUB-SOIL CONDITION
NOT APPLICABLE
FOUNDATION TYPE
NOT APPLICABLE
MATERIALS:
DENSITY OF ALUMINIUM = 2.7
DENSITY OF STEEL = 7.85
DENSITY OF GLASS = 2.5
MODULUS OF ELESTICITY OF ALUMINIUM = 70000 N/mMA2.
ALUMINIUM ALLOY USED FOR PROFILES - AA 6063-T 6
ALUMINIUM ALLOY USED FOR BRACKETS - AA 6082-6
PERMISSIBLE DEFLECTION
DUE TO WIND LOADING
SPAN / 175, FOR SPAN < 4115 MM
SPAN / 240 +6 MM, FOR SPAN > 4115 MM
ANCHORS USED
‘M10 / M12 EXPANSION ANCHOR BOLTS
COMPUTER PROGRAMME
USED
STAADPRO 2007TYPICAL GLAZING UNITS
ews Chye 4-57)
Thi unt lected at Ground foor, RTA. hal
Desion wind tas
Design wind load ie assessed as. per BS: 6300: Part2: 1997, as per Standard
method,
The design wind loads are given in pages ( 125° 124)
The Unit CW 05 is located at Zone B
Design wind load pressure considered = 1348 Nim'2
Design wind load suction considered 1170
Mulion spacings considered 4200 mm , 1000 mm,
Intensity of wind load on malion im 1348 x (12 #10) 12
1481 kN
The mullons are supported on 3 nos, brackets as chown.
The wind load onthe mullon is shownin page ( S!
ou
Mulion used : Profle M 19910-@:
. = msoino at
y 428000, mm Cee v9)
S = seo nav
* 2468 0m
. 228 wn
‘Auminium alley used for mulions - AA 6063-76
Maximum moment = 1923 kN ep > SD
Factores moment 212 1829
£135 tthe
Relering to 8S: 8118: Part: 1901, 1-43.22 wD?
Be bit of dit (Forelements under compression)
Beaxb/t or gx dit (Forelements under stess gradient)
bit = 500/31 (for element 1)
462 Cp ww)
@xd/t ag x ( 312 +750) 1 22 ( for element 2)
30
Where ¢ is the ses gradient and read fom fg, 42
In fig. 42,ye_and yo are the distances fom the nesta als of the gross section to
the more heaviy compressed edge andthe oer edge respecvely che element
{akon postive towards the compression side.
yorye 2.312 / 750 =.042
ou, 9-057 Chap Mle 2
493 x 057
For yo/ye
®
Toke as the higher ofthese to,
» =18
For intemal elomonts,( unwelded elements, rom able 4.3,
Mat. fo = 226 ep we
foe sum soy eos3- T8
po. = 160N/ nev?
pa =A75N imma Ce vay
pe =95N/mma
= (250/90 }