Professional Documents
Culture Documents
Simple3x3x3LEDCubewithArduinoAll
http://instructables-pdf.abuouday.com/download.php
1/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
2/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
3/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
4/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
5/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
6/63
3/20/2016
ShowAllItems
This is my first instructable so leave feedback in the comments please.
When viewing lots of LED Cube tutorials it seemed like they were too complex and like
they didn't give enough detail on how to build them. Also the pick controlled ones had very
complex coding and complex wiring. Most cubes looked really bad lacking good building
instructions like the picture above. So I decided to make this one that is very simple and
good for beginners wanting to make something that looks good.
http://instructables-pdf.abuouday.com/download.php
7/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
8/63
3/20/2016
ShowAllItems
Partsneeded:
T o
3x22kohmresistorsResistors22K
3x2N3904NPNtransistorTransistorsNPN
27xLED's(pickcolourIused5mm)LEDs
9x200ohmresistors200Ohmresistors
o l s
Tinnedcopperwire(canjustremovecasingfromsinglecorewirebutitwillbe
orange)TinnedCopperWire(Iuseddifferentwirebutthelistinghasended)
PrefboardMatrixBoard
SolderSolder
Wires
OptionalParts:
MaleandfemaleheadersFemaleHeadersMaleHeaders
RibboncableRainbowRibbonCable
Tools:
SolderingIron
*(2x)Pliers(2or1andaClamp)
*Clamp
Wirecutters(pliersmighthavethis)
OptionalTools:
HotGlueGun(+Glue)
Saw(ifprefboardistoobig)
*Fluxpaste
9/63
3/20/2016
Thiswebsiteusescookies
Thiswebsiteusescookiestoimproveuserexperience.Byusingourwebsiteyouconsenttoallcookiesin
accordancewithourCookiePolicy.
Iagree
Readmore
Freecookieconsentbycookiescript.com
http://instructables-pdf.abuouday.com/download.php
10/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
11/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
12/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
13/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
14/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
15/63
3/20/2016
ShowAllItems
Tape the template on a piece of cardboard and poke small holes in it with scissors at the
joins. Then push an led into each to make the holes the same size as an led (or if you have
a drill and a 5mm drill bit drill the holes).
Straighten the bridge wire by putting one end in a clamp and holding the other end in
pliers and puling will straighten the wire. If you don't have a clamp use 2 sets of pliers, put
an end in each and pull. You will need 15 pieces of straight wire for all 3 layers together
a bit longer than the length of the template.
Put an led in each hole and bend the positive legs (longer legs) at around 45 degrees from
the lines shown in the pictures.
Cut the shorter legs standing up down to the little square in the metal (in picture).
Once the legs are cut put a straight piece of the bridge wire across all of the legs in a row
that are standing and solder it on each leg, do this for the other two rows also. (Labelled
Pic1)
When the rows are done place more bridge wire across the end of them and solder it to
all 3 rows. (Labelled Pic2)
Do again twice to make 3 layers.
img159.pdf
16/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
17/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
18/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
19/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
20/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
21/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
22/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
23/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
24/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
25/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
26/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
27/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
28/63
3/20/2016
ShowAllItems
You will need 11 of the straightened wires. (Cut one in half to make 12)
To mark where the layers are going to go put a light under the cardboard template then
the board on top so the light shines through the holes making it easy to mark them. Once
marked slide a piece of wire down each hole on the board keeping it standing straight and
solder it on the copper side.
Slide the first layer down the wires and solder the remaining LED legs not connected to
anything else on to the wires that are pointing up and trim the excess off of the LED
legs.
Do the same to the next layer but to get the correct height turn a 9-Volt battery on its side
and use it as a spacer.
For the last layer do the same again except put another battery on top as another spacer.
When done trim all the long legs and the long wires going to the top.
Test the cube and make sure all the LED's light up if not they might need to be rehttp://instructables-pdf.abuouday.com/download.php
29/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
30/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
31/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
32/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
33/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
34/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
35/63
3/20/2016
ShowAllItems
Put the transistors in at the layer connections and solder them there connecting the
collector (C) to the layers.
Put a 22k resistor in connected to the base (B) with the other leg going down the board
like a wire.
Connect the emitters (E) together as they are going to ground.
http://instructables-pdf.abuouday.com/download.php
36/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
37/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
38/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
39/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
40/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
41/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
42/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
43/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
44/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
45/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
46/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
47/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
48/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
49/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
50/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
51/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
52/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
53/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
54/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
55/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
56/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
57/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
58/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
59/63
3/20/2016
ShowAllItems
Bring all the legs of the rails down to one point and solder a resistor to them. I have used
wire to "Jump over" the ground "rail" making it neater I have also used hot glue as an
insulator. The picture labelled wiring shows this and the picture labelled resistors also
shows this.
When all the wires are at a point solder wires (header pins or sockets) onto the board to
be able to connect them to the Arduino. I have used header pins and made cables to
connect the cube to an Arduino. To make it so much easier to connect pins or sockets to a
cable apply some flux paste to the pins or sockets.
The wires are connected to the Arduino as shown in the last picture.
60/63
3/20/2016
ShowAllItems
Ground wire goes to a ground pin.
Layer 1 goes to pin 11
Layer 2 goes to pin 12
Layer 3 goes to pin 13
Rail 1 goes to pin 10
Rail 2 goes to pin 9
Rail 3 goes to pin 8
Rail 4 goes to pin 7
Rail 5 goes to pin 6
Rail 6 goes to pin 5
http://instructables-pdf.abuouday.com/download.php
61/63
3/20/2016
http://instructables-pdf.abuouday.com/download.php
62/63
3/20/2016
ShowAllItems
The code will be uploaded soon but to get started use the led cube library available I do
not own and did not create the led library, it has a licence file included in the zip file.
LED Library
https://github.com/gziprduino-ledcube
LedCubeExample
Downloaded using:
instructables-pdf.abuouday.com Privacy Policy
http://instructables-pdf.abuouday.com/download.php
63/63