Professional Documents
Culture Documents
d. Only A & C
e. All of the above.
10.Intersecting point for WBS and OBS
a. Cost account
b. Intersect matrix
c. Project matrix
d. None of above
11. For operation and designed auto mobile factory
a. Mechanical Engineer
b. Civil Engineer
c. Chemical Engineer
d. Petroleum Engineer
12. Which of the following discipline is most suitable for doing a natural
gas pipeline work?
a. Mechanical Engg
b. Petroleum Engg
c. Chemical Engg
d. Civil Eng
13. Gypsum board at residence and industrial building used except
a. Low cost
b. Ease of installation
c. Recyclability
14. Stress defined
a. Strain time force
b. Mass divide volume
c. Pressure time length
d. None of above
15. What is the last of estimation for project
a. Estimation
b. Assembly schedule
16. Which one of the following is suitable in engineering
manner? Decision shall be based on
reason than sit
uation .
a. Quantity Thinking.
b. Logical Thinking.
c. Interpersonal Skills.
d. Honesty.
17. What is QSAS?
a. Qatar Sustainability Assessment System
18. An activity in a project network can be represented by which of the
following?
a. Arrow
b. Line
c. Node
d. All of the above
19. Before starting work at site, the major factor has to be checked is?
a. Access to site (EFE)
b. Storage of Water, tools & equipments
c. Safety
d. Approval from MMUP / Civil / Defence etc.
e. All of the above
20. Software programming flow
a. Plan, Do, Check, Act
b. Plan, Do, Act, Check
c. Plan, Act, Do, Check
21. First step of Scope planning starts with
a. Budgeting
b. Current earning estimation
c. Objectives and requirements to satisfy customer
22. In network which point getting more inward flow
a. Float
b. Critical path
c. Slack
d. Merging point
23. What is the least level of WBS
a. Deliverable
b. Cost
c. Work package
d. Lowest sub deliverable
24. The best place to build an exhibition and convention center (near the
Airport? Or in satellite place far from Urban? Etc)
25. One situation for cancel project.
26. What is the most sensitive period in the project?
Test Q&A
d. Smoke ( something)
23. Corrosion is a result of:
a. Chemical reaction
b. Electro-chemical reaction
c. Both
d. None of the above
24. A system of turbine-generator with efficiency of turbine is 90%
and efficiency of generator is80%. The overall system efficiency is
a. 10%
b. 100%
c. 72%
d. 170%
http://www.scribd.com/doc/230926876/MMUP-Sample-Questions-PMP-NonEE#scribd
Model Test 1
15
Aesthetic standards
In order to create an attractive, functional development, aesthetic
standards have been established. These standards will promote
a consistent, orderly appearance that will help preserve property
values and provide assurance to tenants and investor sab out the quality of
development that will occur around them. The aesthetic standards address
components of a plot plan that will affect the visual quality of the plot as
viewed from off-plot locations. In addition, these components affect the
experience of on-plot workforce in their very day lives. Figures 6-62 and 6-63
below illustrate graphic guidelines for plot landscaping, plot wall character and
main signage for the logistics, support, & light industrial land Use Zone. For an
attractive and consistent appearance throughout the logistics and industrial Zones,
each plot
should have a distinct front side and back side. In general, the front
side should contain the main office and parking within a landscaped setting.
The sides and rear of the plot can be more utilitarian and contain loading areas,
utility structures and other ancillary uses that are generally screened from view of
public roads.
COMPONENT DESIGN STANDARD
Location of Offices
Offices shall be located at the front of the building facing the road. Where Mezzanine
office are considered a dedicated and separate entry shall be provided that is
distinguished from warehouse structure and is commensurate with commercial office
aesthetics.
Outdoor torage Areas
Any outdoor storage area (including garaged in storage areas and liquid waste
storage tanks) shall not be located within the Front setback. Any outdoor storage area
must be screened from the road.
Mechanical Equipment & Utility structures
In general, mechanical equipment and utility structures shall be screened
from offsite views:
At grade water tank and mechanical equipment shall be located to the side and rear
of the building.
Roof-top water tank and mechanical equipment shall be screened from view and not
be visible from the road.
Landscaping
A landscaping strip with a minimum average width of 1.5 m shall be
provided along all road frontages except across vehicle crossings and
where a guardhouse is located in the road boundary setback. The
landscaping strip must contain:
Minimum 1 tree and one additional tree for every 10m of roads frontage.
Where three or more trees are required these trees shall be planted no more than
15mapart or closer than 5m apart.
Trees shall be of a species capable of reaching a minimum height at maturity of 8m
andshall not be less than 1.5m high at the time of planting.
Walls &Fencing
Walls and fences are permitted under the following conditions:
On the read and side of the property, solid walls are allowed up to a height of 2.5m
however, on the front of the property and any external boundary solid walls only up to
a height of 1.4m above which a tubular metal fence with minimum 80%opacity may
be erected. The total height of this barrier shall not be more than 2.5m.
The following types of fences shall not be permitted on any side of the
plot:
Bar bed wire fencing.
Buildings shall display variety in forms, material and color to reflect a style
consistent with modern logistics facilities.
The office or non-logistics components of the project shall be expressed
differently from that of the warehouses.
Ancillary buildings and service buildings shall be architecturally treated with colors and
materials appropriate to fit within the architectural style of the main warehouse
facilities