You are on page 1of 903

WCDMA RAN

Handover Feature Parameter Description


Issue

01

Date

2014-04-30

HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2014. All rights reserved.


No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions


and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and
recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any
kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.


Address:

Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China

Website:

http://www.huawei.com

Email:

support@huawei.com

Contents
1 About This Document
1.1 Scope
1.2 Intended Audience
1.3 Change History
1.4 Differences Between Base Station Types

2 Overview of Handover
3 Intra-Frequency Handover
3.1 Overview
3.1.1 Intra-Frequency Soft Handover
3.1.2 Intra-Frequency Hard Handover
3.1.3 Inter RNC Handover
3.2 Intra-Frequency Handover Procedure
3.3 Intra-Frequency Handover Measurement
3.3.1 Intra-Frequency Handover Measurement Quantities
3.3.2 Intra-Frequency Handover Measurement Events
3.3.3 Triggering of Event 1A
3.3.4 Triggering of Event 1B
3.3.5 Triggering of Event 1C
3.3.6 Triggering of Event 1D
3.4 Intra-Frequency Handover Decision and Execution
3.5 Follow-up Procedures for Soft Handover Failures
3.5.1 Overview
3.5.2 Rate Reduction After an SHO Failure
3.5.3 D2F Transition After a Soft Handover Failure
3.5.4 E2D Reconfiguration After a Soft Handover Failure
3.6 Signaling Procedures for Intra-Frequency Handover
3.6.1 Intra-NodeB Intra-Frequency Soft Handover Signaling Procedure
3.6.2 Intra-RNC Inter-NodeB Intra-Frequency Soft Handover Signaling Procedure
3.6.3 Inter-RNC Intra-Frequency Soft Handover Signaling Procedure
3.6.4 Intra-RNC Inter-NodeB Intra-Frequency Hard Handover Signaling Procedure
3.6.5 Inter-RNC Intra-Frequency Hard Handover Signaling Procedure
3.7 Addition of Detected Set Cells to the Active Set
3.8 TTI Switch or E2D for BE Services Based on P-CPICH RSCP
3.9 Weak-Coverage-based or Low-Load-based SRB HS-DSCH to DCH

4 Inter-Frequency and Inter-RAT Handover


4.1 Overview

4.2 Inter-frequency and Inter-RAT Handover Switches


4.3 Signaling Procedures for Inter-Frequency Handover
4.3.1 Inter-Frequency Handover Within One RNC
4.3.2 Inter-Frequency Handover Between RNCs
4.4 Signaling Procedures for Inter-RAT Handover
4.4.1 3G-to-2G Handover in the CS Domain
4.4.2 3G-to-2G Handover in the PS Domain
4.4.3 3G-to-2G Handover in Both CS Domain and PS Domain
4.4.4 2G-to-3G Handover in the CS Domain
4.4.5 2G-to-3G Handover in the PS Domain

5 Coverage-based or QoS-based Handover


5.1 Coverage-based or QoS-based Handover Procedure
5.2 Coverage-based or QoS-based Handover Measurement
5.2.1 Overview
5.2.2 Coverage-based or QoS-based Handover Measurement Report Modes
5.2.3 Coverage-based or QoS-based Handover Measurement Quantity
5.2.4 Neighboring Cells to Be Measured
5.2.5 Coverage-based or QoS-based Handover Measurement Events
5.2.6 Penalty for Measurement Failures
5.2.7 BSIC Verification Requirements for 2G Cells
5.2.8 Inter-Frequency Measurements in Batches
5.3 Coverage-based or QoS-based Handover Decision and Execution
5.3.1 Inter-Frequency Coverage-based or QoS-based Handover Decision and Execution
5.3.2 3G-to-2G Coverage-based and QoS-based Handover Decision and Execution
5.4 Rules for 3G-to-2G Coverage-based or QoS-based Handover
5.5 3G-to-2G NACC
5.6 3G-to-2G PS Handover
5.7 2G-to-3G Handover
5.8 System Processing After a Handover Failure
5.8.1 Inter-Frequency Handover Failure
5.8.2 Inter-RAT Handover Failure

6 Non-Coverage-based Handover
6.1 Load-based Inter-Frequency Handover
6.1.1 Load-based Inter-Frequency Handover Procedure
6.1.2 Load-based Inter-Frequency Handover Measurement
6.1.3 Load-based Inter-Frequency Handover Decision and Execution
6.2 Load-based Inter-RAT Handover
6.2.1 Load-based Inter-RAT Handover Procedure

6.2.2 Load-based Inter-RAT Handover Measurement


6.2.3 Load-based Inter-RAT Handover Decision and Execution
6.3 Service-based Inter-RAT Handover
6.3.1 Switches for Service-based Inter-RAT Handover
6.3.2 Service-based Inter-RAT Handover Procedure
6.4 Rules for Enabling Load-based or Service-based Inter-RAT Handover
6.5 Interchanging Inter-RAT Load Information

7 HSPA Handover
7.1 HSDPA Handover
7.1.1 HSDPA Intra-Frequency Handover
7.1.2 HSDPA Inter-Frequency Handover
7.1.3 HSDPA Inter-RAT Handover
7.2 HSUPA Handover
7.2.1 HSUPA Intra-Frequency Handover
7.2.2 HSUPA Inter-Frequency Handover
7.2.3 HSUPA Inter-RAT Handover
7.3 HSPA+ Handover
7.3.1 Overview
7.3.2 Preselection Phase
7.3.3 Fallback Phase
7.3.4 Retry Phase
7.4 Anti-Frequent Serving Cell Change
7.5 HSPA Retry

8 HCS Handover
8.1 Overview
8.2 HCS Handover Procedure
8.3 UE Speed Estimation
8.4 HCS Handover Measurement
8.5 HCS Handover Execution
8.5.1 Inter-Layer Handover in Fast Movement
8.5.2 Inter-Layer Handover in Slow Movement
8.6 Signaling Procedure of HCS Handover
8.7 Interoperability Between HCS Handover and Other Handovers
8.7.1 Interoperability Between HCS Handover and Intra-Frequency Handover
8.7.2 Interoperability Between HCS Handover and Inter-Frequency Handover
8.7.3 Interoperability Between HCS Handover and Inter-RAT Handover

9 Blind Handover
9.1 Overview

9.2 Triggering of Event 1F


9.3 Blind Handover Based on Event 1F

10 Handover Protection
10.1 Anti-Ping-Pong
10.2 Handover Retry
10.2.1 Inter-Frequency Handover Retry
10.2.2 Inter-RAT (3G-to-2G) Handover Retry
10.3 Inter-RAT Multimedia Fallback
10.4 Transferring Event Report to Periodical Report

11 Neighboring Cell Combination


11.1 Overview
11.2 Neighboring Cell Combination Switches
11.3 Procedure of the Neighboring Cell Combination

12 Missing Neighboring Cell Detection


12.1 Overview
12.2 Missing Intra-Frequency Neighboring Cell Detection
12.3 Missing Inter-Frequency or Inter-RAT Neighboring Cell Detection

13 Compressed Mode
13.1 Overview
13.2 Compressed Mode Switches
13.3 Compression Methods
13.4 Compression Types
13.5 Measurement Timer Length
13.6 Check of Compressed Mode Parameter Settings During Inter-RNC Handover
13.7 Compatibility Switch for Dual-frequency Receiver
13.8 Compatibility Switches for HSPA

14 Related Features
14.1 WRFD-01061006 HSDPA Mobility Management
14.2 WRFD-01061204 HSUPA Mobility Management
14.3 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS
14.4 WRFD-020309 Inter-RAT Handover Based on DL QoS

15 Network Impact
15.1 WRFD-020302 Inter Frequency Hard Handover Based on Coverage
15.1.1 System Capacity
15.1.2 Network Performance
15.2 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS
15.2.1 System Capacity

15.2.2 Network Performance


15.3 Inter Frequency Hard Handover Based on UL QoS
15.3.1 System Capacity
15.3.2 Network Performance
15.4 WRFD-020309 Inter-RAT Handover Based on DL QoS
15.4.1 System Capacity
15.4.2 Network Performance
15.5 Inter-RAT Handover Based on UL QoS
15.5.1 System Capacity
15.5.2 Network Performance
15.6 WRFD-01061006 HSDPA Mobility Management

16 Engineering Guidelines
16.1 WRFD-020201 Intra Node B Softer Handover
16.1.1 Requirements
16.1.2 Activation
16.1.3 MML Command Examples
16.1.4 Activation Observation
16.1.5 Deactivation
16.1.6 MML Command Examples
16.2 WRFD-020202 Intra RNC Soft Handover
16.2.1 Requirements
16.2.2 Activation
16.2.3 MML Command Examples
16.2.4 Activation Observation
16.2.5 Deactivation
16.2.6 MML Command Examples
16.3 WRFD-020203 Inter RNC Soft Handover
16.3.1 Requirements
16.3.2 Activation
16.3.3 MML Command Examples
16.3.4 Activation Observation
16.3.5 Deactivation
16.3.6 MML Command Examples
16.4 WRFD-020301 Intra Frequency Hard Handover
16.4.1 Requirements
16.4.2 Activation
16.4.3 MML Command Examples
16.4.4 Activation Observation

16.4.5 Deactivation
16.4.6 MML Command Examples
16.5 WRFD-01061204 HSUPA Mobility Management
16.5.1 Requirements
16.5.2 Activation
16.5.3 Activation Observation
16.5.4 Deactivation
16.6 WRFD-01061404 HSUPA 2ms/10ms TTI Handover
16.6.1 Requirements
16.6.2 Activation
16.6.3 Activation Observation
16.6.4 Deactivation
16.7 WRFD-021200 HCS (Hierarchical Cell Structure)
16.7.1 Requirements
16.7.2 Activation
16.7.3 MML Command Examples
16.7.4 Activation Observation
16.7.5 Deactivation
16.7.6 MML Command Examples
16.8 WRFD-020302 Inter Frequency Hard Handover Based on Coverage
16.8.1 When to Use This Feature
16.8.2 Required Information
16.8.3 Requirements
16.8.4 Activation
16.8.5 MML Command Examples
16.8.6 Activation Observation
16.8.7 Deactivation
16.8.8 MML Command Examples
16.8.9 Performance Monitoring
16.9 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS
16.9.1 When to Use This Feature
16.9.2 Required Information
16.9.3 Requirements
16.9.4 Activation
16.9.5 MML Command Examples
16.9.6 Activation Observation
16.9.7 Deactivation
16.9.8 MML Command Examples
16.10 Inter Frequency Hard Handover Based on UL QoS

16.10.1 When to Use This Feature


16.10.2 Required Information
16.10.3 Requirements
16.10.4 Activation
16.10.5 MML Command Examples
16.10.6 Activation Observation
16.10.7 Deactivation
16.10.8 MML Command Examples
16.11 WRFD-020303 Inter-RAT Handover Based on Coverage
16.11.1 Requirements
16.11.2 Activation
16.11.3 MML Command Examples
16.11.4 Activation Observation
16.11.5 Deactivation
16.11.6 MML Command Examples
16.12 WRFD-020309 Inter-RAT Handover Based on DL QoS
16.12.1 Requirements
16.12.2 Activation
16.12.3 MML Command Examples
16.12.4 Activation Observation
16.12.5 Deactivation
16.12.6 MML Command Examples
16.13 Inter-RAT Handover Based on UL QoS
16.13.1 Requirements
16.13.2 Activation
16.13.3 MML Command Examples
16.13.4 Activation Observation
16.13.5 Deactivation
16.13.6 MML Command Examples
16.14 WRFD-020308 Inter-RAT Handover Phase 2
16.14.1 Requirements
16.14.2 Deployment
16.15 WRFD-02030801 NACC(Network Assisted Cell Change)
16.15.1 Requirements
16.15.2 Activation
16.15.3 MML Command Examples
16.15.4 Activation Observation
16.15.5 Deactivation
16.15.6 MML Command Examples

16.16 WRFD-02030802 PS Handover Between UMTS and GPRS


16.16.1 Requirements
16.16.2 Activation
16.16.3 MML Command Examples
16.16.4 Activation Observation
16.16.5 Deactivation
16.16.6 MML Command Examples
16.17 WRFD-020305 Inter-RAT Handover Based on Service
16.17.1 Requirements
16.17.2 Activation
16.17.3 MML Command Examples
16.17.4 Activation Observation
16.17.5 Deactivation
16.17.6 MML Command Examples
16.18 WRFD-020306 Inter-RAT Handover Based on Load
16.18.1 Requirements
16.18.2 Activation
16.18.3 MML Command Examples
16.18.4 Activation Observation
16.18.5 Deactivation
16.18.6 MML Command Examples
16.19 WRFD-020310 3G/2G Common Load Management
16.19.1 Requirements
16.19.2 Activation
16.19.3 MML Command Examples
16.19.4 Activation Observation
16.19.5 Deactivation
16.19.6 MML Command Examples
16.20 WRFD-01061006 HSDPA Mobility Management
16.20.1 Requirements
16.20.2 Activation
16.20.3 Activation Observation
16.20.4 Deactivation

17 Parameters
18 Counters
19 Glossary
20 Reference Documents

1 About This Document


1.1 Scope
This document describes handover, including its technical principles, network impact, and engineering
guidelines. This document covers the following features:

WRFD-020201 Intra NodeB Softer Handover

WRFD-020202 Intra RNC Soft Handover

WRFD-020203 Inter RNC Soft Handover

WRFD-020301 Intra Frequency Hard Handover

WRFD-01061204 HSUPA Mobility Management

WRFD-01061404 HSUPA 2 ms/10 ms TTI Handover

WRFD-021200 HCS (Hierarchical Cell Structure)

WRFD-020302 Inter Frequency Hard Handover Based on Coverage

WRFD-020304 Inter Frequency Hard Handover Based on DL QoS

WRFD-020303 Inter-RAT Handover Based on Coverage

WRFD-020309 Inter-RAT Handover Based on DL QoS

WRFD-020308 Inter-RAT Handover Phase 2

WRFD-02030801 NACC(Network Assisted Cell Change)

WRFD-02030802 PS Handover Between UMTS and GPRS

WRFD-020305 Inter-RAT Handover Based on Service

WRFD-020306 Inter-RAT Handover Based on Load

WRFD-020310 3G/2G Common Load Management

1.2 Intended Audience


This document is intended for personnel who:

Need to understand the features described herein

Work with Huawei products

1.3 Change History


This section provides information about the changes in different document versions. There are two types
of changes, which are defined as follows:

Feature change
Changes in features of a specific product version

Editorial change
Changes in wording or addition of information that was not described in the earlier version

RAN16.0 01 (2014-04-30)

This issue includes the following changes.

Change Type

Chan

Feature change

Added descriptions about the principle and


3G-to-2G NACC.
Added engineering guidelines for deployin
handovers. For details, see 16.10 Inter Fre
Added engineering guidelines for deployin
For details, see 16.13 Inter-RAT Handover
Added descriptions about that RTWP of th
inter-frequency handover. For details, see
based Handover Decision and Execution

Editorial change

None

RAN16.0 Draft B (2014-02-28)


This issue includes the following changes.

Change Type
Feature change
Editorial change
RAN16.0 Draft A (2014-01-20)
Compared with Issue 05 (2013-12-30) of RAN15.0, Draft A (2014-01-20) of RAN16.0 includes the
following changes.

Change Type
Feature change

Change Descri

Changed the optimized algorithm switches for adding de

Added the descriptions of principles and engineering gu


(RIM) procedure that is implemented through the eCoor
sections:

5.5 3G-to-2G NACC

16.14 WRFD-020308 Inter-RAT Handover Phase

Editorial change

16.15 WRFD-02030801 NACC(Network Assiste


16.16 WRFD-02030802 PS Handover Between U

Added the following sections:

Change Type

Change Descri

14.1 WRFD-01061006 HSDPA Mobility Manage


15.6 WRFD-01061006 HSDPA Mobility Manage

16.20 WRFD-01061006 HSDPA Mobility Manag

1.4 Differences Between Base Station Types


This document applies to the following types of base stations.

Base Station
Macro

Micro

LampSite
Feature Support by Macro, Micro, and LampSite Base Stations

Feature ID
WRFD-020201
Function Implementation in Macro, Micro, and LampSite Base Stations

NA

2 Overview of Handover
Handover is a basic function of the cellular mobile network. The purpose of handover is to ensure that a
UE in CELL_DCH state is served continuously when it moves.
Figure 2-1 shows the handovers supported by the Universal Mobile Telecommunications System (UMTS),
which include intra-frequency handover, inter-frequency handover, and inter-RAT handover.

Figure 2-1 Handovers supported by the UMTS

3 Intra-Frequency Handover
3.1 Overview
Intra-frequency handover is classified into:

Intra-frequency soft handover: Multiple radio links are connected to the UE at the same time
during handover.

Intra-frequency hard handover: Only one radio link is connected to the UE during handover.

3.1.1 Intra-Frequency Soft Handover


Intra-frequency soft handover is more commonly used than intra-frequency hard handover. The types of
intra-frequency soft handover are as follows:

Softer handovers: This type of handover occurs within a NodeB, and the NodeB performs
maximum ratio combination for the uplink signals.
Softer handovers can be performed only between cells in the same uplink resource group. The
downlink resource group configurations of different base station types affect softer handovers as
follows:

For a DBS3800 series base station earlier than RAN13.0, softer handovers cannot be
performed between cells configured on different baseband boards. For a DBS3800 series base
station of RAN13.0 or later, softer handovers can be performed between cells configured on
different boards as long as the boards are not HBBU boards, for example, between cells
configured on different EBBC boards, cells configured on an EBBC board and an EBBD board,
or cells configured on an EBBCD and an EBBC board. If a UE is in a cell configured on an
HBBU board, the target cell of the softer handover must be configured on the same HBBU
board.

For a DBS3900 series base station earlier than RAN13.0, softer handovers cannot be
performed between cells that are configured in different downlink resource groups. For a
DBS3900 series base station of RAN13.0 and later, softer handovers can be performed
between cells that are configured in different downlink resource groups.

The downlink resource group configurations of the BTS3812E/BTS3812AE have no


impact on softer handovers.

Intra-RNC inter-NodeB soft handover: This type of handover is implemented by the WRFD020202 Intra RNC Soft Handover feature. During this type of handover, the RNC performs selective
combination for uplink signals.

Inter-RNC soft handover: This type of handover is implemented by the WRFD-020203 Inter RNC
Soft Handover feature. During this type of handover, the RNC performs selective combination for
uplink signals.

Intra-frequency soft handover is characterized by the function that the UE can be connected to multiple
Universal Terrestrial Radio Access Network (UTRAN) access points at the same time. Addition and
release of radio links are controlled by the ACTIVE SET UPDATE procedure.
Table 3-1 Differences between soft handover and softer handover

Item
Scenario

Item
Uplink signal
Downlink signal
Resource use
The HoSwitch(BSC6900,BSC6910): HO_INTRA_FREQ_SOFT_HO_SWITCH parameter is used to
determine whether to enable both soft handover and softer handover. By default, this switch is set to ON,
indicating that both soft handover and softer handover are enabled. After the RNC receives the event 1A,
1B, 1C, or 1D report, it initiates the corresponding soft handover procedure for the UE. For example, the
RNC can add or delete links.
The DivCtrlField(BSC6900,BSC6910) parameter indicates whether maximum-ratio combination is
enabled in the uplink during softer handover. When the NodeB decides not to perform maximum-ratio
combination (softer combination), the RNC performs selective combination.
If a soft or softer handover over the Iur interface is triggered and the intra-frequency cells are configured
in different uplink resource groups, CMP_IUR_SHO_DIVCTRL_SWITCH of
theCmpSwitch(BSC6900,BSC6910) parameter must be set to ON. Under this circumstance, the NodeB
determines whether to combine the RLs on the NodeB based on the value
ofDivCtrlField(BSC6900,BSC6910).
The HoSwitch(BSC6900,BSC6910): HO_INTRA_FREQ_SOFT_HO_SWITCH parameter is used to
determine whether to enable soft handover. By default, this switch is set to ON, indicating that soft
handover is enabled. After the RNC receives the event 1A, 1B, 1C, or 1D report, it initiates the
corresponding soft handover procedure for the UE. For example, the RNC can add or delete links.
If a soft handover over the Iur interface is triggered and the intra-frequency cells are configured in
different uplink resource groups, CMP_IUR_SHO_DIVCTRL_SWITCH of
theCmpSwitch(BSC6900,BSC6910) parameter must be set to ON.

3.1.2 Intra-Frequency Hard Handover


Intra-frequency hard handover (WRFD-020301 Intra Frequency Hard Handover) refers to a handover
where all the old radio links are released before the new radio links are established. Compared with soft
handover, intra-frequency hard handover uses fewer resources.
The scenarios of intra-frequency hard handover are as follows:

No Iur interface is present between RNCs. In this scenario, intra-frequency hard handover instead
of soft handover can be performed between two RNCs.
The intra-frequency soft handover fails and the intra-frequency hard handover is allowed.
When the intra-frequency soft handover fails because of a congestion problem of the target cell, the
RNC tries an intra-frequency hard handover.

The HoSwitch(BSC6900,BSC6910): HO_INTRA_FREQ_HARD_HO_SWITCH parameter is used to


determine whether to enable the intra-frequency hard handover. By default, this switch is set to ON.

3.1.3 Inter RNC Handover


When the target cell under the target RNC fulfills the criteria for the intra-frequency soft handover, intra- or
inter-frequency hard handover, the conditions that the handover over Iur is triggered are as follows:

Whether the Iur interface is available depends on the setting of the following two parameters according to
handover types:

Whether intra- or inter- frequency hard handover is allowed over the Iur interface depends on the
setting of the HHOTRIG(BSC6900,BSC6910) parameter.

Whether inter RNC soft Handover is allowed depends on the setting of


the SHOTRIG(BSC6900,BSC6910) parameter.

The SHOTRIG(BSC6900,BSC6910) parameter consists of three sub-switches:

CS_SHO_SWTICH: If CS_SHO_SWTICH is checked, soft handover for CS services over the Iur
interface is allowed.

HSPA_SHO_SWTICH: If HSPA_SHO_SWTICH is checked, soft handover for HSPA services


over the Iur interface is allowed.

NON_HSPA_SHO_SWTICH: If NON_HSPA_SHO_SWTICH is checked, soft handover for nonHSPA PS services over the Iur interface is allowed.

If the RRC connection has been set up but the Radio Bearers (RBs) have not, whether a cross-Iur soft
handover can be executed is determined by theHO_MC_SIGNAL_IUR_INTRA_SWITCH switch under
the HoSwitch(BSC6900,BSC6910) parameter. Only if the switch is set to ON, can the cross-Iur soft
handover be executed.

3.2 Intra-Frequency Handover Procedure


The intra-frequency handover procedure involves three phases: handover measurement, handover
decision, and handover execution.
After the UE transits to the CELL_DCH state in connected mode during a call, the RNC sends a
MEASUREMENT CONTROL message to instruct the UE to take measurements and report the
measurement event results.
The MEASUREMENT CONTROL message carries the following information:

Event trigger threshold

Hysteresis value

Event trigger delay time

Neighboring cell list

Upon the reception of an event report from the UE, the RNC makes a handover decision and performs
the corresponding handover, as shown in Figure 3-1.

Figure 3-1 Intra-frequency handover procedure

3.3 Intra-Frequency Handover Measurement


In the measurement phase, the UE takes measurements according to the MEASUREMENT CONTROL
message received from the RNC. When the event triggering conditions are met, the UE sends
measurement reports to the RNC according to the rules defined in the MEASUREMENT CONTROL
message.

3.3.1 Intra-Frequency Handover Measurement Quantities


Intra-frequency handover uses Ec/N0 or RSCP of the CPICH as the measurement value. Intra-frequency
handover measurement quantity can be configured through the
parameterIntraFreqMeasQuantity(BSC6900,BSC6910).

3.3.2 Intra-Frequency Handover Measurement Events


In intra-frequency handover, the UE reports measurement results to the RNC through event reporting.
Table 3-2 Events reported by the UE

1A
1B
1C
1D
3.3.3 Triggering of Event 1A
Event 1A is triggered under the following condition:

10 x Log (MNew) + CIONew W x 10 x Log (

) + (1 - W) x 10 x Log (MBest) - (R1a - H1a/2)

MNew is the measurement value of the cell in the reporting range.

CIONew is equal to the sum of CIO(BSC6900,BSC6910) and CIOOffset(BSC6900,BSC6910),


which adjusts the cell boundary in the handover algorithms. This parameter is determined by
network planning according to actual environment configuration. To facilitate handover in
neighboring cell configuration, the parameter is set as a positive value; otherwise, the parameter is
set as a negative value.

W represents weighted factor, which is determined by the


parameter Weight(BSC6900,BSC6910). The total quality of the best cell and the active set is
specified by W.

Mi is the measurement value of a cell in the active set.


NA is the number of cells not forbidden to affect the reporting range in the active set. The
parameter CellsForbidden1A(BSC6900,BSC6910) indicates whether adding the cell to the active
set affects the relative threshold of event 1A.

MBest is the measurement value of the best cell in the active set.
R1a is the reporting range or the relative threshold of soft handover. The threshold parameters of
the CS non-VP services, CS VP services, and PS services are as follows:

IntraRelThdFor1ACSNVP(BSC6900,BSC6910)

IntraRelThdFor1ACSVP(BSC6900,BSC6910)

IntraRelThdFor1APS(BSC6900,BSC6910)

NOTE:
For the PS and CS combined services, the thresholds for CS services are used.
For the single signaling connection of the UE, the thresholds for CS services are used.

H1a represents HystFor1A(BSC6900,BSC6910) the hysteresis value of event 1A

Figure 3-2 shows the triggering of event 1A. In this procedure, the default parameter values (W=0, H 1a =0)
are used.

Figure 3-2 Triggering of event 1A when W = 0 and H1a = 0

A: signal quality curve of the best cell in the active set

B: signal quality curve of a cell in the monitored set

C: curve of Th1A

Reporting range for event 1A is equal to the value


of IntraRelThdFor1ACSVP(BSC6900,BSC6910), IntraRelThdFor1ACSNVP(BSC6900,BSC6910),
orIntraRelThdFor1APS(BSC6900,BSC6910).

In Figure 3-2, Th1A = (CPICH Ec/N0 of the best cell in the active set) - (reporting range for event 1A)
If the signal quality of a cell that is not in the active set is higher than Th 1A for a period of time specified
by TrigTime1A(BSC6900,BSC6910) (that is, Time to trigger in Figure 3-2), the UE reports event 1A.
If W > 0 and H1a = 0, then Th1A = (general signal quality of all the cells in the active set) - (reporting range
for event 1A).

3.3.4 Triggering of Event 1B


Event 1B is triggered under the following condition:

10 x Log (Mold) + CIOold W x 10 x Log (

) + (1-W) x 10 x Log (MBest) - (R1b+H1b/2)

MOld is the measurement value of the cell that becomes worse.

CIOOld is equal to the sum of CIO(BSC6900,BSC6910) and CIOOffset(BSC6900,BSC6910),


which is the offset between the cell in the reporting range and the best cell in the active set.

W represents weighted factor, used to weight the quality of the active set. The total quality of the
best cell and the active set is specified by the parameterWeight(BSC6900,BSC6910).

Mi is the measurement value of a cell in the active set.


NB is the number of cells not forbidden to affect the reporting range in the active set. The
parameter CellsForbidden1B(BSC6900,BSC6910) indicates whether adding the cell to the active
set affects the relative threshold of event 1B.

MBest is the measurement value of the best cell in the active set.
R1b is the reporting range or the relative threshold of soft handover. The threshold parameters of
the CS non-VP services, CS VP services, and PS services are as follows:

IntraRelThdFor1BCSNVP(BSC6900,BSC6910)

IntraRelThdFor1BCSVP(BSC6900,BSC6910)

IntraRelThdFor1BPS(BSC6900,BSC6910)

NOTE:
For the PS and CS combined services, the thresholds for CS services are used.
If the UE currently has only signaling connections, the thresholds for CS services are used.

H1b is the hysteresis value of event 1B, which is determined by the


parameter Hystfor1B(BSC6900,BSC6910).

Configuration rule and restriction

The value of IntraRelThdFor1BCSNVP(BSC6900,BSC6910) has to be larger than that


of IntraRelThdFor1ACSNVP(BSC6900,BSC6910).

The value of IntraRelThdFor1BCSVP(BSC6900,BSC6910) has to be larger than that


of IntraRelThdFor1ACSVP(BSC6900,BSC6910).

The value of IntraRelThdFor1BPS(BSC6900,BSC6910) has to be larger than that


of IntraRelThdFor1APS(BSC6900,BSC6910).

Figure 3-3 shows the triggering of event 1B. In this procedure, the default parameter values (W=0, H 1b =0)
are used.

Figure 3-3 Triggering of event 1B when W = 0 and H1b = 0

A: signal quality curve of the best cell in the active set

B: signal quality curve of the non-best-cell in the active set

C: curve of Th1B

Reporting range for event 1B is equal to the value


of IntraRelThdFor1BCSVP(BSC6900,BSC6910), IntraRelThdFor1BCSNVP(BSC6900,BSC6910),
orIntraRelThdFor1BPS(BSC6900,BSC6910).

In Figure 3-3,
Th1B = (CPICH Ec/N0 of the best cell in the active set) - (reporting range for event 1B)
If the signal quality of a cell in the active set is lower than Th1B for a period of time specified
by TrigTime1B(BSC6900,BSC6910) (Time to trigger in Figure 3-3), the UE reports event 1B.
If W > 0 and H1b = 0, then Th1B = (general signal quality of all the cells in the active set) - (reporting range
for event 1B).

3.3.5 Triggering of Event 1C


Event 1C is triggered under the following condition:
10 x Log (MNew) + CIONew 10 x Log (MInAS) + CIOInAS + H1c/2

MNew is the measurement value of the cell in the reporting range.


CIONew is the cell individual offset value of the cell in the reporting range. It is equal to the sum
of CIO(BSC6900,BSC6910) and CIOOffset(BSC6900,BSC6910), which is the offset between the
cell in the reporting range and the best cell in the active set.

MInAS is the measurement value of the worst cell in the active set.

H1c is the hysteresis value of event 1C, which is determined by the


parameter Hystfor1C(BSC6900,BSC6910).

Figure 3-4 shows the triggering of event 1C. In this procedure, the default parameter values are used.
Figure 3-4 Triggering of event 1C

A: signal quality curve of the best cell in the active set

B: signal quality curve of a cell in the active set

C: signal quality curve of the worst cell in the active set

D: signal quality curve of a cell in the monitored set

E: curve of Th1C

Th1C = (CPICH Ec/N0 of the worst cell in the active set) + (hysteresis/2)
where

Hysteresis is equal to the value of Hystfor1C(BSC6900,BSC6910).

If the signal quality of a cell not in the active set is higher than Th 1C for a period of time specified
by TrigTime1C(BSC6900,BSC6910) (Time to trigger in the figure), the UE reports event 1C, as shown in
the figure.
The UE reports event 1C for qualified cells after the number of cells in the active set reaches the
maximum value. The maximum number of cells in the active set can be set by
theMaxCellInActiveSet(BSC6900,BSC6910) parameter.

3.3.6 Triggering of Event 1D

Event 1D is triggered under the following condition:


10 x Log (MNotBest) + CIONotBest 10 x Log (MBest) + CIOBest + H1d/2

MNotBest is the measurement value of a cell that is not the best cell.
CIONotBest is equal to the sum of CIO(BSC6900,BSC6910) and CIOOffset(BSC6900,BSC6910),
which is the offset between the cell in the reporting range and the best cell in the active set.

MBest is the measurement value of the best cell in the active set.

CIOBest is the cell individual offset value of the best cell.

When the HO_CIO_1D_USED option in the HoSwitch(BSC6900,BSC6910) parameter


for the SET UCORRMALGOSwitch command is selected, the value of CIOBest equals the
value of the CIO(BSC6900,BSC6910)parameter, which is set by running the ADD
UCELLSETUP command.

When the HO_CIO_1D_USED option in the HoSwitch(BSC6900,BSC6910) parameter for


the SET UCORRMALGOSwitch command is not selected, the value of CIOBest is 0.

H1d is the hysteresis value of event 1D, which is determined by the


parameter Hystfor1D(BSC6900,BSC6910).

Figure 3-5 shows the triggering of event 1D. In this procedure, the default parameter values are used.
Figure 3-5 Triggering of event 1D

A: signal quality curve of the best cell in the active set

B: signal quality curve of a cell in the active set or the monitored set

C: curve of Th1D

Hysteresis is equal to the value of Hystfor1D(BSC6900,BSC6910).

If the signal quality of a cell not in the active set is higher than Th 1D for a period of time specified
by TrigTime1D(BSC6900,BSC6910) (Time to trigger in the figure), the UE reports event 1D.

3.4 Intra-Frequency Handover Decision and Execution


The intra-frequency handover decision and execution procedure depends on the different measurement
events that the RNC receives.
When receiving an event 1A, 1C, or 1D report, the RNC adds a target cell to the active set only when the
CPICH Ec/N0 of the target cell is higher than the absolute thresholdSHOQualmin(BSC6900,BSC6910).
NOTE:
To enable the UEs in the cells in the monitored set to report event 1D, you need to turn on the intrafrequency hard handover switch, that is, select theHO_INTRA_FREQ_HARD_HO_SWITCH switch of
the HoSwitch(BSC6900,BSC6910) parameter in the SET UCORRMALGOSWITCH command.
Table 3-3 lists different types of intra-frequency handover decision and execution based on different
events.
Table 3-3 Intra-frequency handover decision and execution

1A

1B

1C

1D

When the only RAB of a PS service is released, RAB_REL_SRV_CELL_CHG_CROSS_SWITCH in


the OptimizationSwitch3(BSC6900,BSC6910) parameter in the SET URRCTRLSWITCH command
specifies whether to initiate a serving cell change procedure.

When this switch is set to ON, a serving cell change procedure is not allowed.

When this switch is set to OFF, a serving cell change procedure is allowed.

3.5 Follow-up Procedures for Soft Handover Failures

3.5.1 Overview
If a soft handover fails, the RNC follows up by performing the following procedures:
1.

Rate reduction
For a UE processing R99 non-real-time services (abbreviated as NRT services) in uplink and
downlink, if the RNC fails to set up a radio link for the UE during the admission phase of a soft
handover, the RNC reduces the service rate of the UE and then sets up a radio link again,
increasing the soft handover success rate. For details, see section3.5.2 Rate Reduction After an
SHO Failure.

2.

State transition from Cell_DCH to Cell_FACH (D2F for short)


If the RNC fails to set up a radio link for a UE during a soft handover, the RNC triggers a D2F
transition for the UE in the best cell when the target cell's signal quality is greater than the best
cell's signal quality plus a preset threshold value. This is to reduce the interference to the target cell
caused by UEs processing R99 NRT services in the uplink. For details, see section 3.5.3 D2F
Transition After a Soft Handover Failure.

3.

Channel reconfiguration from E-DCH to DCH (E2D for short)


If the RNC fails to set up a radio link for an HSUPA UE during a soft handover or the target cell
does not support E2D reconfiguration for HSUPA UEs, the RNC triggers the E2D reconfiguration
procedure for the HSUPA UE. This is to reduce the interference to the target cell caused by UEs
processing HSUPA NRT services in the uplink. For details, see section 3.5.4 E2D Reconfiguration
After a Soft Handover Failure.

For a UE processing R99 NRT services in uplink and downlink, the following principles apply after a soft
handover failure:

If the UE service rate can be reduced, the RNC reduces the UE service rate as described in
section 3.5.2 Rate Reduction After an SHO Failure

If the UE service rate cannot be reduced because the rate reduction algorithm has not taken
effect or the UE has been using the guaranteed bit rate (GBR), the RNC triggers a D2F transition
when the conditions are met, as described in section 3.5.3 D2F Transition After a Soft Handover
Failure
NOTE:

The follow-up procedures for soft handover failures reduce the possibility of received total wideband
power (RTWP) or channel element (CE) congestion in a cell but increase the number of RB
reconfigurations and the call drop rate.

3.5.2 Rate Reduction After an SHO Failure


If the radio link fails to be added for a soft handover, the rate reduction is triggered for R99 NRT services
to increase the probability of a successful soft handover.

Estimation Procedure for Rate Reduction

If the RNC receives a 1A, 1C, or 1D measurement report, the RNC tries to add the corresponding
cell to the active set. If the addition fails, the RNC performs the estimation procedure for rate
reduction.

Figure 3-6 Estimation procedure for rate reduction

1.

The RNC evaluates whether the measurement quantity of the cell failing to be admitted meets the
condition of rate reduction.

If the condition is met, the RNC performs a rate reduction process for the access service
immediately, as described in the "Procedure of Rate Reduction Execution" section.
If the condition is not met, the RNC performs the next step (Step 2).
The condition of rate reduction is as follows: Mnew >
Mbest_cell - RelThdForDwnGrd(BSC6900,BSC6910)

2.

Mnew is the CPICH Ec/N0 measurement value of the cell failing to be admitted.

Mbest_cell is the CPICH Ec/N0 measurement value of the best cell in the active set.

RelThdForDwnGrd(BSC6900,BSC6910) is a parameter.

The RNC evaluates whether the number of SHO failures in the cell exceeds
the ShoFailNumForDwnGrd(BSC6900,BSC6910).

If the number of SHO failures in the cell is smaller than


the ShoFailNumForDwnGrd(BSC6900,BSC6910):

If the timer has not been started, the RNC starts it.

If the timer has been started, the RNC increments the SHO failure counter by one.
The timer length is set through the parameter ShoFailPeriod(BSC6900,BSC6910).
The SHO failure counter of a cell is used to record the number of SHO failures in this cell. For
each UE, the RNC records the number of SHO failures in three cells at most. For SHO failures
in any other cells, the RNC does not record the number.
Before the SHO failure evaluation timer expires, no action is taken and the RNC waits for the
next measurement report period.
When the SHO failure evaluation timer expires, the RNC sets the SHO failure counter of the
corresponding cell to 0 and ends the evaluation.

If the number of SHO failures in the cell is larger than or equal to the
parameter ShoFailNumForDwnGrd(BSC6900,BSC6910), the RNC performs a rate reduction
process for the access service,

Procedure of Rate Reduction Execution


Figure 3-7 Procedure of rate reduction execution

1.

The RNC performs a rate reduction process for the access service.
To determine the access rate after the rate reduction, see the "Rate Negotiation at Admission
Control" section in Load Control Feature Parameter Description.

If the rate reduction fails, the RNC sets the SHO failure counter of the cell to 0 and ends the rate
reduction process.
2.

If the rate reduction succeeds, the RNC makes an admission decision for the UE.

If admitting the UE to the cell succeeds, the RNC adds this cell to the active set without
measurement and adds the radio link for the UE.

If admitting the UE to the cell fails, the RNC starts the penalty timer
(DcccShoPenaltyTime(BSC6900,BSC6910)) to avoid a rate increase triggered by DCCC
within the period. When the penalty timer expires, the RNC sets the SHO failure counter of
the cell to 0 and ends the rate reduction process.

If the RNC fails to perform a soft handover again, it performs the estimation and execution
procedures, as previously described.
3.5.3 D2F Transition After a Soft Handover Failure
When the D2F transition switch for soft handover failures is turned on, the RNC triggers a D2F transition
procedure in the best cell for a UE processing R99 NRT services in the uplink (R99 or HSDPA NRT
services in the downlink) if the UE experiences a soft handover failure and the following inequation
applies:
Target cell's Ec/N0 > Best cell's Ec/N0 + D2F quality offset for soft handover failures
When the preceding inequation applies, the interference to the target cell caused by the UE is greater
than that to the best cell.
When the D2F transition of the UE succeeds, the RNC starts a penalty timer for state transitions from
Cell_FACH to Cell_DCH (F2D for short).

F2D transitions for the UE are forbidden until the penalty timer expires or the UE initiates a CS
service.
The penalty timer stops if a cell update occurs due to the cell change.

To turn on the D2F transition switch for soft handover failures, set
the SoftFailD2FSwitch(BSC6900,BSC6910) parameter to ON. The D2F quality offset is determined by
setting theSoftFailD2FOffset(BSC6900,BSC6910) parameter. The value of the F2D penalty timer is
determined by setting the SoftFailF2DPunishTimer(BSC6900,BSC6910) parameter.
The preceding parameters can be set by running the SET UINTRAFREQHO command.

3.5.4 E2D Reconfiguration After a Soft Handover Failure


If the RNC fails to set up a radio link for a UE processing HSUPA NRT services in the uplink during a soft
handover or the target cell does not support E2D reconfiguration for HSUPA UEs, the RNC triggers the
E2D reconfiguration procedure for the UE. This is to reduce the uplink interference to the target cell
caused by the UE.
To turn on the E2D reconfiguration switch for soft handover failures, set
the SoftFailE2DSwitch(BSC6900,BSC6910) parameter in the SET UINTRAFREQHO command to ON.
When an E2D reconfiguration procedure for a UE succeeds, the RNC starts a penalty timer for the UE.
During the penalty period, periodic DRDs for the UE, including blind-handover-based periodic DRDs and
measurement-based periodic DRDs, are forbidden; D2E reconfiguration triggered by dynamic channel
configuration control (DCCC) is forbidden; D2E state transition is forbidden if the target cell does not
support HSUPA. The value of the penalty timer is fixed to 20s. For details about periodic DRDs,
see Directed Retry Decision Feature Parameter Description.
NOTE:

The RNC does not trigger E2D reconfiguration for the UE if the soft handover fails due to a downlink
admission failure. This is because the uplink resources of the target cell are not congested if only a
downlink admission failure occurs.

3.6 Signaling Procedures for Intra-Frequency Handover


3.6.1 Intra-NodeB Intra-Frequency Soft Handover Signaling Procedure
This section describes the signaling procedure for intra-frequency soft handover within a NodeB.
Figure 3-8 shows the procedure for intra-frequency soft handover when the UE moves from one cell to
another cell within the same NodeB.
Figure 3-8 Procedure for intra-NodeB intra-frequency soft handover

The connections involved in the intra-NodeB intra-frequency softer handover change are as follows:

Before the softer handover, only cell 1 is connected to the UE.

During the softer handover, both cell 1 and cell 2 are connected to the UE.

After the softer handover, only cell 2 is connected to the UE. Cell 1 is removed from the active
set.

Figure 3-9 Signaling procedure for intra-NodeB intra-frequency soft handover

3.6.2 Intra-RNC Inter-NodeB Intra-Frequency Soft Handover Signaling Procedure


This section describes the signaling procedure for intra-RNC inter-NodeB intra-frequency soft handover.
Figure 3-10 Procedure for intra-RNC inter-NodeB intra-frequency soft handover

Before the soft handover, only NodeB 1 is connected to the UE.

During the soft handover, both NodeBs are connected to the UE.
After the soft handover, only NodeB 2 is connected to the UE. The active set of NodeB 1 is
removed.
Figure 3-11 Signaling procedure for intra-RNC inter-NodeB intra-frequency soft handover

3.6.3 Inter-RNC Intra-Frequency Soft Handover Signaling Procedure


This section describes the signaling procedure for inter-RNC intra-frequency soft handover.

Figure 3-12 Procedure for inter-RNC intra-frequency soft handover

Before the soft handover, the UE is connected to NodeB 1 and NodeB 2.


After the SRNC makes a soft handover decision, it sets up a connection between NodeB 3 under
another RNC and the UE, and releases the connection between NodeB 1 and the UE.

Figure 3-13 Signaling procedure for inter-RNC intra-frequency soft handover

3.6.4 Intra-RNC Inter-NodeB Intra-Frequency Hard Handover Signaling Procedure


The signaling procedure of intra-NodeB intra-frequency hard handover is similar to that of Intra-RNC interNodeB intra-frequency hard handover. This section describes the signaling procedure for only the intraRNC inter-NodeB intra-frequency hard handover.

Figure 3-14 Procedure for intra-RNC inter-NodeB intra-frequency hard handover

Figure 3-15 Signaling procedure for intra-RNC inter-NodeB intra-frequency hard handover

As shown in Figure 3-15, NodeB 1 is the source NodeB and NodeB 2 is the target NodeB.

3.6.5 Inter-RNC Intra-Frequency Hard Handover Signaling Procedure


Figure 3-16 shows the procedure for intra-frequency hard handover when a UE moves from one NodeB in
an SRNC to another NodeB in a DRNC.
Figure 3-16 Procedure for inter-RNC intra-frequency hard handover

Figure 3-17 Signaling procedure for inter-RNC intra-frequency hard handover

As shown in Figure 3-17, NodeB 1 is the source NodeB and NodeB 2 is the target NodeB.

3.7 Addition of Detected Set Cells to the Active Set


A detected set cell is not in a UE's neighboring cell list, which is contained in the measurement control
message. However, according to section 10.3.7.39 "Intra-frequency measurement reporting criteria" in
3GPP TS 25.331 V10.0.0, like a monitored set cell, a detected set cell can also be contained in an intrafrequency measurement report triggered by a 1X (1A, 1C, and 1D) event. In this way, a detected set cell
can be added to the active set of the UE.
Whether a detected set cell can be contained in a measurement report triggered by a 1X event is
controlled by the HO_INTRA_FREQ_DETSET_RPRT_SWITCH under
theHOSWITCH(BSC6900,BSC6910) parameter in the SET UCORRMALGOSWITCH command.

When this switch is turned on, the UE reports the information about both monitored set cells and
detected set cells.

When this switch is turned off, the UE reports the information about monitored set cells only.

Whether a detected set cell can be added to the active set of a UE is controlled by
the HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH under
theHOSWITCH(BSC6900,BSC6910) parameter in the SET UCORRMALGOSWITCH command.

When this switch is turned on, a detected set cell can be added to the active set of a UE.
However, such a detected set cell must be a neighboring cell of a certain cell in the active set.

When this switch is turned off, a detected set cell cannot be added to the active set of a UE.

The optimized algorithm for adding detected set cells to the active set is controlled
by HO_INTRA_FREQ_DETSET_INTO_ACTSET of the HoSwitch(BSC6900,BSC6910) parameter in
the SET UALGORSVPARA command.

When this switch is turned on, the RNC performs the following operations after receiving a UE's
measurement report triggered by a 1A, 1C, or 1D event:
If the reported cell is in the intra-frequency neighboring cell list sent from the RNC to the UE, the
RNC adds the reported cell to the active set of the UE.
If the reported cell is not in the intra-frequency neighboring cell list, the RNC searches for the
reported cell among the neighboring cells of all active set cells and the intra-frequency neighboring
cells of the best cell's intra-frequency neighboring cells.

If only one intra-frequency neighboring cell has the same scrambling code as the
reported cell and is under the UE's SRNC, the SRNC adds the reported cell to the active set.

If only one intra-frequency neighboring cell has the same scrambling code as the
reported cell but is under the UE's DRNC, the SRNC performs different operations depending
on the value of HO_INTRA_FREQ_DETSET_INTO_ACTSET under
the HoSwitch(BSC6900,BSC6910) parameter in the SET UALGORSVPARAcommand:
If HO_INTRA_FREQ_DETSET_INTO_ACTSET is set to ON, the RNC adds this cell to the
active set.
If HO_INTRA_FREQ_DETSET_INTO_ACTSET is set to OFF, the RNC does not add this cell
to the active set.

If no or multiple intra-frequency neighboring cells have the same scrambling code as the
reported cell, the RNC does not add the reported cell to the active set.

When this switch is turned off, the RNC checks whether the cell in the measurement report
triggered by a 1A, 1C, or 1D event is also in the intra-frequency neighboring cell list sent from the
RNC to the UE. If the cell is in the list, the RNC adds the cell to the active set. Otherwise, the RNC
does not add the cell to the active set.
NOTE:

When the HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH under the HoSwitch parameter is


turned on, the HO_INTRA_FREQ_DETSET_RPRT_SWITCH under theHOSWITCH parameter and
the HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH under the HOSWITCH parameter do not
need to be turned on, because the first switch incorporates the functions of the latter two switches.

3.8 TTI Switch or E2D for BE Services Based on P-CPICH RSCP


The function TTI Switch or E2D for BE Services Based on P-CPICH RSCP applies to UEs that have
established an RRC connection or RAB. For details about TTI switch, see HSUPA TTI selection Feature
Parameter Description. For details about E2D for UEs that have established an RRC connection,
see Radio Bearers Feature Parameter Description. For details about E2D for UEs that have established
an RAB, see State Transition Feature Parameter Description.

Periodic P-CPICH RSCP Measurement for UEs with an RRC Connection

Upon receiving an RRC CONNECTION SETUP COMPLETE message from a UE, the RNC
sends a measurement control message to the UE, instructing the UE to start a periodic P-CPICH
RSCP measurement task if the following conditions are both met:

Either DRA_BASE_COVER_BE_TTI_INIT_SEL_SWITCH in
the DraSwitch(BSC6900,BSC6910) parameter
or DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH in
theDraSwitch2(BSC6900,BSC6910) parameter is turned on. In
addition, BASE_RSCP_BE_TTI_E2D_INITSEL_EFFECT_SWITCH in
the RscpEffectAlgoSwitch parameter is turned on.

The value of the Establishment cause IE in the RRC CONNECTION REQUEST message is any
of the following: Originating Streaming Call, Originating Interactive Call, Originating Background
Call, Originating Subscribed traffic Call, Terminating Streaming Call, Terminating Interactive Call,
Terminating Background Call, Originating High Priority Signalling, Terminating High Priority
Signalling, Inter-RAT cell re-selection, and Inter-RAT cell change order.

If either of the preceding conditions is not met, the RNC does not send a measurement control
message to the UE.
The UE periodically reports measurement reports in unacknowledged mode (UM), thereby
preventing call drops caused by SRB-triggered RLC
reset.RrcRscpPeriodTimer(BSC6900,BSC6910) specifies the interval at which the UE
reports measurement reports. IntraFreqFilterCoef(BSC6900,BSC6910) specifies the
filtering coefficient.
Periodic P-CPICH RSCP Measurement for UEs with an RAB

After a UE has established a service or a reconfiguration procedure is complete, the RNC sends a
measurement control message to the UE, instructing the UE to start a periodic P-CPICH RSCP
measurement task or stop the current one and start a new task if the following conditions are both
met:

Either DRA_BASE_COVER_BE_TTI_RECFG_SWITCH in the DraSwitch parameter


or DRA_BASE_COVER_BE_E2D_SWITCH in the DraSwitch2 parameter is turned on. In
addition, BASE_RSCP_BE_TTI_E2D_RECFG_EFFECT_SWITCH in
the RscpEffectAlgoSwitch parameter is turned on.
The UE is in the CELL_DCH state and has established a PS BE service.

If either of the preceding conditions is not met, the RNC does not send a measurement control
message to the UE or sends a measurement control message to stop periodic P-CPICH RSCP
measurement.
The UE periodically reports measurement reports in UM, thereby preventing call drops caused
by SRB-triggered RLC reset. RabRscpPeriodTimer specifies the interval at which the UE
reports measurement reports. IntraFreqFilterCoef specifies the filtering coefficient.
3.9 Weak-Coverage-based or Low-Load-based SRB HS-DSCH to DCH
The function Weak-Coverage-based or Low-Load-based SRB HS-DSCH to DCH is introduced to improve
the SRB over HSDPA call drop rate. The SRB HS-DSCH to DCH is triggered based on the P-CPICH

RSCP and Ec/N0 measurement results. Therefore, the periodic P-CPICH RSCP and Ec/N0 measurement
must be enabled. For details, see HSPA Evolution Feature Parameter Description.
After a UE has established a service or a reconfiguration procedure is complete, the RNC sends a
measurement control message to the UE, instructing the UE to start a periodic P-CPICH RSCP and
Ec/N0 measurement task or stop the current one and start a new task if the following conditions are both
met:

RESERVED_SWITCH_4_BIT8 in RsvSwitch4(BSC6900,BSC6910) is turned on.


The SRB of the UE is carried over HSDPA, and the UE is in the CELL_DCH state. For details
about SRB over HSDPA, see HSPA Evolution Feature Parameter Description.

If either of the preceding conditions is not met, the RNC does not send a measurement control message
to the UE or sends a measurement control message to stop periodic P-CPICH RSCP and Ec/N0
measurement.
The UE periodically reports measurement reports in UM, thereby preventing call drops caused by SRBtriggered RLC reset. RsvU32Para8(BSC6900,BSC6910) specifies the interval at which the UE reports
measurement reports. IntraFreqFilterCoef(BSC6900,BSC6910) specifies the filtering coefficient.

4 Inter-Frequency and Inter-RAT Handover


4.1 Overview
Based on the handover triggering causes, the inter-frequency and inter-RAT handover falls into five
categories, as described in Table 4-1.
This section mainly describes the 3G-to-2G coverage-based handover and QoS-based handover. Except
the cause of the triggering is different, the handover procedure is the same for the coverage-based
handover and QoS-based handover.
NOTE:
Unless otherwise specified, inter-RAT handover refers to the handover performed between 3G and 2G
networks. For details about the handover between UMTS and LTE networks, seeInteroperability Between
UMTS and LTE Feature Parameter Description.
Table 4-1 Types of inter-frequency and inter-RAT handover

Type
Coverage-based handover

QoS-based handover

Type

Load-based handover

Service-based handover

HCS handover

4.2 Inter-frequency and Inter-RAT Handover Switches


Some switches are important for inter-frequency handover because they decide whether the handover
can be performed successfully. These switches are the parameter values of handover algorithm switches
in the SET UCORRMALGOSWITCH command, as described below.
HOSWITCH(BSC6900,BSC6910)> HO_INTER_FREQ_HARD_HO_SWITCH: The switch decides
whether the RNC allows inter-frequency handover.
HOSWITCH(BSC6900,BSC6910) > HO_INTER_RAT_PS_OUT_SWITCH: The switch decides whether
the RNC allows inter-RAT handover of the PS domain from the UTRAN.
HOSWITCH(BSC6900,BSC6910) > HO_INTER_RAT_CS_OUT_SWITCH: The switch decides whether
the RNC allows inter-RAT handover of the CS domain from the UTRAN.
HHOTRIG(BSC6900,BSC6910): The switch decides whether intra- or inter- frequency hard handover is
allowed over the Iur interface.
HOSWITCH(BSC6900,BSC6910) > HO_MC_SIGNAL_SWITCH: The switch decides when the RNC
performs the active set signal quality measurement before the RB setup. If the UE is at the cell verge or
the signal is weak signals after accessing the network, the RNC can trigger inter-frequency or inter-RAT
handover when the UE sets up the RRC.

If the switch is set to ON, the RNC initiates the active set quality measurement after the RRC
connection setup is completed (before the RB setup).
The RNC determines whether to allow handovers for UEs with single signaling connections,
depending on the RESERVED_SWITCH_1_BIT30 switch
underRsvSwitch1(BSC6900,BSC6910) in the SET UALGORSVPARA command. The value of the
switch is set based on the situation of subsequent service establishment.

When the switch is turned on, if a service is established after the RRC connection is set
up, the RNC allows handovers for UEs with single signaling connections; if no service is
established after the RRC connection is set up, the RNC prohibits handovers for UEs with
single signaling connections.

When the switch is turned off, the RNC always allows handovers for UEs with single
signaling connections.

If the switch is set to OFF, the RNC initiates the active set quality measurement after the RB
setup is completed.
The switch is set to OFF by default.

HOSWITCH(BSC6900,BSC6910) > HO_MC_MEAS_BEYOND_UE_CAP_SWITCH: The switch decides


whether the neighboring cell will be sent in the inter-frequency measurement control message when the
frequency of the neighboring cell is not included in the measurement capability of the UE. The reported
measurement capability of the UE is not the same as the actual measurement capability of the UE.
Measurement capability at some frequencies may not be reported due to the limitation of the version of
UE protocol.

If the switch is set to ON, the RNC sends the inter-frequency measurement control message with
the neighboring cell, whose frequency is not included in the measurement capability of the UE.

If the switch is set to OFF, the RNC sends the inter-frequency measurement control message
without the neighboring cell, whose frequency is not included in the measurement capability of the
UE.

The switch is set to OFF by default.

4.3 Signaling Procedures for Inter-Frequency Handover


4.3.1 Inter-Frequency Handover Within One RNC
Figure 4-1 shows the inter-frequency handover for a UE that moves from NodeB 1 to NodeB 2 within one
RNC. Before the handover, the UE sets up a connection to NodeB 1. After the handover, the UE sets up a
connection to NodeB 2.
The signaling procedure of inter-frequency handover within one NodeB is similar to the signaling
procedure of the hard handover between NodeBs within one RNC.

Figure 4-1 Inter-frequency handover between NodeBs within one RNC

Figure 4-2 Signaling procedure for inter-frequency handover between NodeBs within one RNC

As shown in Figure 4-2, NodeB 1 is the source NodeB, whereas NodeB 2 is the target NodeB. From step
1 through step 6, a new connection is set up. From step 7 through step 9, the original connection is
released.

4.3.2 Inter-Frequency Handover Between RNCs


Figure 4-3 shows the signaling procedure for inter-frequency hard handover for a UE that moves from a
NodeB to another NodeB between the RNCs. Before the handover, the UE sets up a connection to
NodeB 1. After the handover, the UE sets up a connection to NodeB 2.
Figure 4-3 Inter-frequency hard handover between the RNCs

Figure 4-4 Signaling procedure for inter-frequency hard handover between the RNCs

NodeB 1 is the source NodeB, whereas NodeB 2 is the target NodeB. From step 1 through step 10, a
new connection is set up. From step 11 through step 13, the original connection is released.

4.4 Signaling Procedures for Inter-RAT Handover


4.4.1 3G-to-2G Handover in the CS Domain
Figure 4-5 shows the signaling procedure for the 3G-to-2G handover in the CS domain. The 2G
messages shown in Figure 4-5 are for your reference only.

Figure 4-5 3G-to-2G handover in the CS domain

4.4.2 3G-to-2G Handover in the PS Domain


When a UE in idle mode or connected mode, if the SGSN changes with the shift of the system that the
UE moves from 3G network to 2G network, the inter-SGSN handover will be performed.

The handover procedures are different in the following two cases:

When the UE is in CELL_DCH state


The 3G-to-2G handover in the PS domain is triggered after the UTRAN sends a CELL CHANGE
ORDER FROM UTRAN message.

When the UE is in CELL_FACH, CELL_PCH, or URA_PCH state


The 3G-to-2G handover in the PS domain is triggered through the cell reselection.

The following figure shows an example of handover for the UE in CELL_FACH, CELL_PCH, or
URA_PCH state. When the UE is in idle mode, the cell reselection procedure does not include the
elementary procedures marked "UE CONNECTED" in Figure 4-6.

Figure 4-6 Example of the 3G-to-2G handover in the PS domain

NOTE:
If a UE, either in idle mode or in connected mode, performs a 3G-to-2G handover and the same SGSN
serves the UE before and after the handover, all messages sent to or from the two SGSNs in the
preceding figure will be converged in the same SGSN. In this case, signaling interaction procedures in
steps 3, 5, 7, and 9 are not required.

4.4.3 3G-to-2G Handover in Both CS Domain and PS Domain


This section describes the 3G-to-2G handover in both CS domain and PS domain in detail.

Inter-RAT Handover in Both CS Domain and PS Domain


For a UE in CELL_DCH state using both CS and PS domain services, the inter-RAT handover procedure
is based on the measurement reports from the UE but is initiated from the UTRAN.
The UE performs the inter-RAT handover from UTRA RRC connected mode to GSM connected mode
first. After the UE sends a HANDOVER COMPLETE message to the GSM/BSS, the UE initiates a
temporary block procedure towards the GPRS to suspend the GPRS services. After the CS domain
services are released on the GSM side, the inter-RAT handover in the PS domain is initiated and then
completed.
If the inter-RAT handover from UTRA RRC Connected Mode to GSM Connected Mode succeeds, the
handover is regarded as successful, no matter whether the UE initiates a temporary block procedure
towards the GPRS.
In case of inter-RAT handover failure, the UE may go back to the UTRA RRC Connected Mode and reestablish the connection in the original state.

SGSN Service Suspend and Resume


When the CS connection is terminated, the BSS may send a RESUME message to the SGSN. However,
resume is impossible since the radio access system has changed. Therefore, the SGSN acknowledges
the resume through a RESUME NACK message.
The UE sends a ROUTING AREA UPDATE REQUEST message to the SGSN to resume the GPRS
service. The update mode depends on the network operation mode in use.

Figure 4-7 Intra-SGSN service suspended and resumed

Figure 4-8 Inter-SGSN service suspended and resumed

4.4.4 2G-to-3G Handover in the CS Domain


When a GSM cell has a neighboring UMTS cell, the measurement control information is contained in the
system information. The dual-mode MS performs the inter-RAT measurement in idle timeslots and reports
the measurement result. Then, the BSC decides whether to start the inter-RAT handover according to the
measurement result. To allow 2G-to-3G handovers in the CS domain, the 2G-to-3G CS handover switch
must be turned on for the RNC. That is, SYSHO_CSIN_PERMIT_SWITCH of
the RsvdPara1(BSC6900,BSC6910) parameter in theSET URRCTRLSWITCH command must be
selected.
The GSM system uses time division multiple access technology, and the inter-RAT measurement is
performed in idle timeslots. Therefore, the GSM does not need to support the compressed mode.

Figure 4-9 2G-to-3G handover in the CS domain

4.4.5 2G-to-3G Handover in the PS Domain


Figure 4-10 shows the 2G-to-3G handover in the PS domain.

Figure 4-10 2G-to-3G handover in PS domain

5 Coverage-based or QoS-based Handover


If a moving UE leaves the coverage area of the current frequency or the link quality in the uplink or
downlink degrades, the RNC triggers a coverage-based or QoS-based inter-frequency or inter-RAT
handover to avoid call drops. The QoS-based handover procedure is the same as the coverage-based
handover procedure in the uplink or downlink.

5.1 Coverage-based or QoS-based Handover Procedure


Figure 5-1 shows the procedure for the coverage-based or QoS-based handover.
Figure 5-1 Coverage-based or QoS-based handover procedure

In the triggering phase


If the CPICH signal quality of the current cell becomes worse, the UE reports event 2D. Upon receipt
of event 2D, the RNC decides:

Whether to trigger a coverage-based inter-frequency handover. For details, see


section 5.3.1 Inter-Frequency Coverage-based or QoS-based Handover Decision and
Execution.

Whether to trigger a coverage-based inter-RAT handover. For details, see section 5.3.2
3G-to-2G Coverage-based and QoS-based Handover Decision and Execution.

Whether to trigger a coverage-based UMTS-to-LTE PS handover. For details,


see Interoperability Between UMTS and LTE Feature Parameter Description.
If the service quality of the current cell deteriorates, the link stability control algorithm decides
whether to trigger a QoS-based handover. If a QoS-based handover is required, the RNC
initiates a QoS-based handover. For details about the triggering conditions of QoS-based
handovers for CS services, see the "Link Stability Control for AMR" section in AMR Feature
Parameter Description. For details about the triggering conditions of QoS-based handovers for
BE services, see the "Link Stability Control for BE" section in DCCC Feature Parameter
Description.

In the measurement phase


The RNC sends a measurement control message to the UE. Upon receipt of this message, the UE
performs inter-frequency or inter-RAT handover measurement.
In this phase, the method of either periodical measurement report or event-triggered measurement
report can be used.

In the decision phase


The RNC makes a handover decision based on event 2B, event 3A, or periodical measurement
report sent by the UE.

In the execution phase


The RNC performs the handover procedure.

5.2 Coverage-based or QoS-based Handover Measurement


5.2.1 Overview
If the UE can perform measurement only in compressed mode during the measurement phase, the RNC
needs to start the compressed mode before sending a measurement control message to the UE.
Otherwise, the RNC can directly send a measurement control message to the UE. Upon receipt of the
measurement control message, the UE performs inter-frequency or inter-RAT handover measurement.
For details about the compressed mode, see chapter 13 Compressed Mode.
Two RNC-level
timers, CsHoPrioMeasTimerLen(BSC6900,BSC6910) and PsHoPrioMeasTimerLen(BSC6900,BSC69
10), are available in the SET UHOCOMM command.
These timers specify the time interval from the time when an inter-frequency measurement control
message for CS or PS services is sent to the time when an inter-RAT measurement control message for
CS or PS services is sent. When a UE processing a CS or PS service is about to perform an interfrequency or inter-RAT handover, the RNC preferentially sends the UE an inter-frequency measurement
control message after compressed mode is started. If no inter-frequency neighboring cell meets the
required conditions or the inter-frequency handover fails, the RNC sends the UE an inter-RAT
measurement control message after the corresponding timer expires.

If CsHoPrioMeasTimerLen(BSC6900,BSC6910) or PsHoPrioMeasTimerLen(BSC6900,BSC69
10) is set to 0, the RNC sends the UE an inter-frequency measurement control message and an
inter-RAT measurement control message at the same time.

If CsHoPrioMeasTimerLen(BSC6900,BSC6910) or PsHoPrioMeasTimerLen(BSC6900,BSC69
10) is set to a non-zero value, the RNC preferentially sends the UE an inter-frequency measurement
control message. The RNC sends the UE an inter-RAT measurement control message only after the
corresponding timer expires.

The cell-level
timers CsHoPrioMeasTimerLen(BSC6900,BSC6910) and PsHoPrioMeasTimerLen(BSC6900,BSC691
0) are available in the ADD UCELLHOCOMM command. The meanings of the cell-level timers are the
same as those of the RNC-level timers. When both the cell- and RNC-level timers are set, the cell-level
timers prevail. During a handover, the timers in the best cell prevail.
During a coverage-based handover, if the CPICH signal quality of the current cell improves, the UE
reports event 2F. Then, the RNC stops the compressed mode and the coverage-based handover. For the
conditions for stopping a QoS-based handover for CS services, see the "Link Stability Control for AMR"
section in AMR Feature Parameter Description. For the conditions for stopping a QoS-based handover for
BE services, see the "Link Stability Control for BE" section in DCCC Feature Parameter Description.
The measurement control message contains the measurement report mode, measurement quantities,
neighboring cells to be measured, and parameters for measurement events.
When the measurement report conditions are met, the UE sends measurement reports to the RNC in
event-triggered report mode or periodical report mode. Based on the measurement reports received from
the UE, the RNC determines whether to perform a handover.

5.2.2 Coverage-based or QoS-based Handover Measurement Report Modes


The coverage-based and QoS-based handovers use event-triggered or periodical measurement report
mode.

InterFreqReportMode(BSC6900,BSC6910): The measurement report mode of inter-frequency


handover.

InterRatReportMode(BSC6900,BSC6910): The measurement report mode of inter-RAT


handover.

PrdReportInterval(BSC6900,BSC6910): The periodical measurement report interval of interfrequency handover.

InterRATPeriodReportInterval(BSC6900,BSC6910): The periodical measurement report


interval of inter-RAT handover.

The advantage of periodical measurement report is that if the handover fails, the RNC reattempts the
handover to the same cell after receiving the periodical measurement report from the UE. This increases
the probability of the success of inter-frequency handover.
Based on the measurement control message received from the RNC, the UE periodically reports the
measurement quality of the target cell. Then, based on the measurement report, the RNC makes the
handover decision and performs handover.

5.2.3 Coverage-based or QoS-based Handover Measurement Quantity


Measurement quantities vary according to the type of inter-frequency or inter-RAT handover.
The used frequency belongs to a UMTS cell and the used frequency measurement quantities are set as
follows:

In inter-frequency or inter-RAT coverage-based or QoS-based handover, event 2B/2D/2F or


periodical measurement takes both CPICH Ec/N0 and RSCP as measurement quantities.
In coverage-based inter-RAT handover, the system delivers both CPICH Ec/N0 and CPICH RSCP
for 2D/2F measurement. To deliberately limit the types of measurement quantity, you can set the
corresponding threshold of the limited measurement quantity to the minimum value. For example, if
event 2D of CS service Ec/N0 can be reported but the RSCP cannot, the
parameter InterRATCSThd2DRSCP(BSC6900,BSC6910) or InterFreqCSThd2DRSCP(BSC6900,
BSC6910) is set to the minimum value, that is, -115.

In a coverage-based inter-frequency or inter-RAT handover, the RNC preferentially delivers an


inter-frequency measurement control message to the UE. If the RNC does not receive any valid
inter-frequency measurement reports until the timer specified by
the CsHoPrioMeasTimerLen(BSC6900,BSC6910) orPsHoPrioMeasTimerLen(BSC6900,BSC691
0) parameter expires (indicating that the UE does not complete the coverage-based inter-frequency
handover), the RNC delivers an inter-RAT measurement control message.

In coverage-based inter-RAT handover, the event 3A measurement quantity is set through


the MeasQuantityOf3A(BSC6900,BSC6910) parameter.

In QoS-based inter-RAT handover, the event 3A measurement quantity is set through


the UsedFreqMeasQuantityForQos3A(BSC6900,BSC6910) parameter.

The unused frequencies belong to a GSM cell, and the unused frequency measurement quantity is
referred to as to GSM RSSI.

5.2.4 Neighboring Cells to Be Measured


The RNC selects target neighboring cells to be measured as follows:
1.

2.

From the neighboring cell list of the best cell, the RNC selects at most two frequencies to be
measured based on the Priority of Coverage-Based Inter-Frequency Handover for neighboring
cells.
The RNC selects neighboring cells to be measured according to the following rules:

When the neighboring cell combination function is enabled, the RNC selects neighboring
cells according to the rules described in chapter 11 Neighboring Cell Combination.

When the neighboring cell combination function is disabled, the RNC selects a maximum
of 32 neighboring cells from the neighboring cell list of the best cell based on the value of the
Priority of Coverage-Based Inter-Frequency Handover for neighboring cells.

The Priority of Coverage-Based Inter-Frequency Handover is specified by


the HOCovPrio(BSC6900,BSC6910) parameter in the ADD UINTERFREQNCELL command.

5.2.5 Coverage-based or QoS-based Handover Measurement Events


When the measurement thresholds are reached, the UE reports the events to the RNC to trigger related
handover procedures.
Table 5-1 describes the measurement events involved in inter-frequency or inter-RAT handover.
Table 5-1 Measurement events involved in inter-frequency handover

2D
2F
2B
3A
For details about event triggering conditions, see section 14.2.1 Inter-frequency reporting events and
14.3.1 Inter-RAT reporting event in 3GPP TS 25.331 V10.0.0.

Triggering of Event 2D

After the trigger conditions of event 2D are fulfilled and maintained until the value of the Event
2D Trigger Delay parameter is reached, the UE sends the event 2D measurement report
message.
Event 2D is triggered on the basis of the following formula:
QUsed TUsed2d - H2d/2

QUsed is the measured quality of the used frequency.

TUsed2d is the absolute quality threshold of the cell that uses the current frequency. It is specified by
the event 2D threshold. The event 2D threshold varies depending on the service type and
measurement quantity, as described in Table 5-2.

H2d is the event 2D hysteresis value. It is used to prevent ping-pong triggering of events 2D and
2F.

The principles for using event 2D-related parameters (event 2D trigger delay, hysteresis for event
2D, and threshold for triggering event 2D) in different scenarios are as follows:

When the neighboring cells are inter-frequency neighboring UMTS cells, event 2D-related
parameters configured for inter-frequency handover are used.

When the neighboring cells are neighboring GSM cells, event 2D-related parameters configured
for inter-RAT handover are used.

When the neighboring cells are neighboring LTE cells, event 2D-related parameters configured
for UMTS-to-LTE handover are used.

When the neighboring cells are neighboring LTE and GSM cells, event 2D-related parameters
configured for inter-RAT handover are used.

When the neighboring cells are neighboring LTE cells and inter-frequency neighboring UMTS
cells, event 2D-related parameters configured for inter-frequency handover are used.

When the neighboring cells are neighboring LTE cells, neighboring GSM cells, and interfrequency neighboring UMTS cells, or when the neighboring cells are neighboring GSM cells and
inter-frequency neighboring UMTS cells, the event 2D-related parameters to be used depend on the
setting of the CoexistMeasThdChoice(BSC6900,BSC6910)parameter.

If this parameter is set to COEXIST_MEAS_THD_CHOICE_INTERFREQ, event 2Drelated parameters configured for inter-frequency handover are used.

If this parameter is set to COEXIST_MEAS_THD_CHOICE_INTERRAT, event 2D-related


parameters configured for inter-RAT handover are used.

NOTE:
The CoexistMeasThdChoice(BSC6900,BSC6910) parameter is an RNC-level parameter and also a celllevel parameter. The RNC-level CoexistMeasThdChoice(BSC6900,BSC6910)parameter can be set by
running the SET UHOCOMM command. The celllevel CoexistMeasThdChoice(BSC6900,BSC6910) parameter can be set by running the ADD
UCELLHOCOMM command. If the cell-level CoexistMeasThdChoice(BSC6900,BSC6910) parameter
has been set, the setting of the RNC-levelCoexistMeasThdChoice(BSC6900,BSC6910) parameter does
not take effect.

Table 5-2 describes event 2D-related parameters.

Table 5-2 Event 2D-related parameters

Scenario

Event

Inter-frequency handover

TimeToTrig2D(BSC6900,BSC6910)

Inter-RAT handover

TrigTime2D(BSC6900,BSC6910)

NOTE:
For the PS and CS combined services, when
the HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH switch under
the HoSwitch(BSC6900,BSC6910) parameter is set to ON, the threshold for triggering event 2D is
specified
by CSPSMRABThd2DEcN0(BSC6900,BSC6910) or CSPSMRABThd2DRSCP(BSC6900,BSC6910) for
inter-frequency or inter-RAT handover. Otherwise, the threshold is set to the higher of the CS or PS
services.
If the UE only has signaling connections, the threshold for triggering event 2D for CS services is used.

Triggering of Event 2F

After the trigger conditions of event 2F are fulfilled and maintained until the value of the Event
2F Trigger Delay parameter is reached, the UE sends the event 2F measurement report message.
Event 2F is triggered on the basis of the following formula:
QUsed TUsed2f + H2f/2

where

QUsed is the measured quality of the used frequency.

TUsed2f is the absolute quality threshold of the cell that uses the current frequency. It is specified by
the event 2F threshold. The event 2F threshold varies depending on the service type and
measurement quantity, as described in Table 5-3.

H2f is the event 2F hysteresis value. It is used to prevent ping-pong triggering of events 2D and
2F.

The principles for using event 2F-related parameters in different networking scenarios are the
same as those for using event 2D-related parameters. For details, see the "Triggering of Event
2D" section. Table 5-3 describes event 2F-related parameters.
Table 5-3 Event 2F-related parameters

Scenario

Event

Inter-frequency handover

TimeToTrig2F(BSC6900,BSC6910)

Inter-RAT handover

TrigTime2F(BSC6900,BSC6910)

NOTE:
For the PS and CS combined services, when
the HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH switch under
the HoSwitch(BSC6900,BSC6910) parameter is set to ON, the threshold for triggering event 2F is
specified
by CSPSMRABThd2FEcN0(BSC6900,BSC6910) or CSPSMRABThd2FRSCP(BSC6900,BSC6910) for
inter-frequency or inter-RAT handover. Otherwise, the threshold is set to the higher of the CS or PS
services.
If the UE only has signaling connections, the threshold for triggering event 2F for CS services is used.

Triggering of Event 2B

After the trigger conditions of event 2B are fulfilled and maintained until the value of
the TimeToTrig2B(BSC6900,BSC6910) parameter is reached, the UE sends the event 2B
measurement report message.
Event 2B is triggered on the basis of the following formula:
QNoused TNoused2b + H2b/2
QUsed TUsed2b - H2b/2
where

QNoused is the measured quality of the cell that uses the other frequencies.

QUsed is the measured quality of the used frequency.

H2b is the event 2B hysteresis value set through the parameter HystFor2B(BSC6900,BSC6910).

TNoused2b is the quality threshold of the cells that use the target frequencies.

Based on the service type and measurement quantity, this threshold can be configured through
the following parameters:

TargetFreqCsThdEcN0(BSC6900,BSC6910)

TargetFreqCsThdRscp(BSC6900,BSC6910)

TargetFreqR99PsThdEcN0(BSC6900,BSC6910)

TargetFreqR99PsThdRscp(BSC6900,BSC6910)

TargetFreqHThdEcN0(BSC6900,BSC6910)

TargetFreqHThdRscp(BSC6900,BSC6910)

TUsed2b is the absolute quality threshold of the cell that uses the current frequency.

TUsed2b is set in the following way:

Based on the service type and measurement quantity, this threshold can be configured through
the following parameters:
If event 2D with the CPICH RSCP value is received by the RNC:

TUsed2b of event 2B with the CPICH RSCP value can be:


UsedFreqCSThdRSCP(BSC6900,BSC6910)
UsedFreqR99PsThdRSCP(BSC6900,BSC6910)
UsedFreqHThdRSCP(BSC6900,BSC6910)

TUsed2b of event 2B with the CPICH Ec/N0 value is configured as the maximum value 0 dB.
According to section 10.37.39 Intra-frequency measurement reporting criteria in 3GPP TS
25.331 V10.0.0, TUsed2b of event 2B with the CPICH Ec/N0 value should be configured as the
maximum value 0 dB. If the event 2F with the CPICH Ec/N0 value is received by the RNC and
TUsed2b of event 2B with the CPICH Ec/N0 value is modified, TUsed2b is reset to 0 dB.
If event 2D with the CPICH Ec/N0 value is received by the RNC:

TUsed2b of event 2B with the CPICH Ec/N0 value can be:


UsedFreqCSThdEcN0(BSC6900,BSC6910)

UsedFreqR99PsThdEcN0(BSC6900,BSC6910)
UsedFreqHThdEcN0(BSC6900,BSC6910)
TUsed2b of event 2B with the CPICH RSCP value is configured as the maximum value -25

dBm.

According to section 10.37.39 Intra-frequency measurement reporting criteria in 3GPP TS


25.331 V10.0.0, TUsed2b of event 2B with the CPICH RSCP value should be configured as the
maximum value -25 dBm. If event 2F with the CPICH RSCP value is received by the RNC and
TUsed2b of event 2B with the CPICH RSCP value is modified, TUsed2b is reset to -25 dBm.

NOTE:
For the PS and CS combined services, when the
switch HoSwitch(BSC6900,BSC6910): HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH is set
to ON, TUsed2b is specified
by CSPSMRABThd2DEcN0(BSC6900,BSC6910) or CSPSMRABThd2DRSCP(BSC6900,BSC691
0), and TNoused2b is specified
byTargetFreqCSPSMRABThdEcNo(BSC6900,BSC6910) or TargetFreqCSPSMRABThdRscp(B
SC6900,BSC6910). Otherwise, the threshold is set to the higher of the CS or PS services.
If the UE only has signaling connections, the thresholds for CS services are used.

Triggering of Event 3A

After the trigger conditions of event 3A are fulfilled and maintained until the value of
the TrigTime3A(BSC6900,BSC6910) parameter is reached, the UE sends the measurement
report of event 3A.
Event 3A is triggered on the basis of the following formula:
QUsed TUsed - H3a/2 and MOtherRAT + CIOOtherRAT TOtherRAT + H3a/2
where

QUsed is the measurement value of the cell at the currently used frequency.
TUsed is the absolute quality threshold of the cell that uses the current frequency. Based on the
service type and measurement quantity in the coverage-based handover, TUsedcan be configured
through the following parameters:

UsedFreqCSThdEcN0(BSC6900,BSC6910)

UsedFreqCSThdRSCP(BSC6900,BSC6910)

UsedFreqHThdEcN0(BSC6900,BSC6910)

UsedFreqHThdRSCP(BSC6900,BSC6910)

UsedFreqR99PsThdEcN0(BSC6900,BSC6910)

UsedFreqR99PsThdRSCP(BSC6900,BSC6910)
In the coverage-based handover, based on the measurement quantity (CPICH Ec/N0 or
RSCP), TUsed is configured as follows:

If the measurement quantity is CPICH Ec/N0:


If event 2D is triggered by RSCP, TUsed is configured as the maximum value 0 dB.

If event 2D is triggered by Ec/N0, TUsed is configured as the Ec/N0 threshold specified by the
previous parameters.
If the measurement quantity is CPICH RSCP:

If event 2D is triggered by RSCP, TUsed is configured as the RSCP threshold specified by the
previous parameters.
If event 2D is triggered by Ec/N0, TUsed is configured as the maximum value -25 dBm.
In the uplink QoS-based handover, based on the measurement quantity (CPICH Ec/N0 or
RSCP), TUsed is configured as the maximum value according to section 10.37.39 Intrafrequency measurement reporting criteria in 3GPP TS 25.331 V10.0.0, as described below:
If the measurement quantity is CPICH Ec/N0, TUsed is configured as the maximum value 0

dB.

If the measurement quantity is CPICH RSCP, TUsed is configured as the maximum value
-25 dBm.
In the downlink QoS-based handover:
If the measurement quantity is CPICH Ec/N0, TUsed is configured as the maximum value 0

dB.

If the measurement quantity is CPICH RSCP, based on the service type, TUsed can be
configured as one of the following sums:
UsedFreqCSThdRSCP(BSC6900,BSC6910)andDlRscpQosHyst(BSC6900,BSC6910)

UsedFreqR99PsThdRSCP(BSC6900,BSC6910)andDlRscpQosHyst(BSC6900,BSC69

10)

UsedFreqHThdRSCP(BSC6900,BSC6910)andDlRscpQosHyst(BSC6900,BSC6910)
MOtherRAT is the measurement value of the cell (in another RAT) in the reporting range.

CIOOtherRAT is the cell individual offset value of the cell (in another RAT) in the reporting range,
which is equal to the sum of CIO(BSC6900,BSC6910) andCIOOffset(BSC6900,BSC6910).

TOtherRAT is the absolute inter-RAT handover threshold. Based on different service types (CS
services, PS R99 services, or PS HSPA services), this threshold can be configured through the
following parameters:

TargetRatCsThd(BSC6900,BSC6910)

TargetRatR99PsThd(BSC6900,BSC6910)

TargetRatHThd(BSC6900,BSC6910)
H3a is 3A hysteresis, the hysteresis value of event 3A.

For the PS and CS combined services, when the


switch HoSwitch(BSC6900,BSC6910): HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH is set
to ON, TUsed is specified
by UsedFreqCSPSThdRSCP(BSC6900,BSC6910) or UsedFreqCSPSThdEcN0(BSC6900,BSC69
10), and TOtherRAT is specified byTargetRatCSPSMRABThd(BSC6900,BSC6910). Otherwise, the
thresholds for CS services are used.

Triggering of Event 3A for UMTS-to-LTE Handover

For details, see Interoperability Between UMTS and LTE Feature Parameter Description.

5.2.6 Penalty for Measurement Failures


For coverage-based or QoS-based handovers, including inter-frequency handovers and 3G-to-2G
handovers, if the UE fails to send a useful measurement report (a measurement report is regarded as
useless if it does not contain any neighboring cells or does not meet the requirement) before the
measurement timer expires, a penalty is imposed on the UE as follows:

If an inter-frequency handover measurement in compressed mode was performed, this


measurement is stopped and the UE is prohibited from performing any inter-frequency handover
measurement in compressed mode triggered by any cause within the duration specified by the
penalty timer.

If a 3G-to-2G handover measurement in compressed mode was performed, this measurement is


stopped and the UE is prohibited from performing any 3G-to-2G handover measurement in
compressed mode triggered by any cause within the duration specified by the penalty timer.

The penalty timer is specified either by an RNC-level or cell-level


parameter PenaltyTimerForCMFailCov(BSC6900,BSC6910). The RNC-level parameter is set using
the SET UHOCOMM command and the cell-level parameter is set using the ADD
UCELLHOCOMM command.
When a UE keeps camping on a cell, it can only initiate one QoS-based inter-frequency or inter-RAT
handover in the cell. Therefore, if a UE fails to perform a QoS-based inter-frequency or inter-RAT
handover in a cell due to the compressed mode penalty, it can no longer initiate the same type of
handover as long as it keeps camping on the cell.

5.2.7 BSIC Verification Requirements for 2G Cells


During inter-RAT measurement, it is recommended that the UE report the 2G cell to the RNC after the
Base Transceiver Station Identity Code (BSIC) of the cell is verified. This greatly enhances the reliability
of handover. The parameter BSICVerify(BSC6900,BSC6910)is the control switch for the BSIC
verification.
After compressed mode is started, if the RNC instructs a UE to measure only neighboring GSM cells
during an inter-RAT handover, the UE needs to measure the RSSI, Init BSIC (initial BSIC verification),
and BSIC Reconfirm (BSIC re-verification). The Init BSIC and BSIC Reconfirm are collectively termed
BSIC verification.
During an inter-RAT handover, the RNC-level
parameters CSBSICVerifyindication(BSC6900,BSC6910) and PSBSICVerifyindication(BSC6900,BSC
6910) in the SET UINTERRATHOCOV command take effect only when BSICVerify(UMTS
BSC6900,UMTS BSC6910) is set to REQUIRED.
CSBSICVerifyindication specifies the BSIC verification mode for CS services.

If CSBSICVerifyindication(BSC6900,BSC6910) is set to BSICINIT_AND_RECONFIRM, both


initial BSIC verification and BSIC re-verification are required.

If CSBSICVerifyindication(BSC6900,BSC6910) is set to BSICINIT, only initial BSIC verification


is required.

PSBSICVerifyindication specifies the BSIC verification mode for PS services.

If PSBSICVerifyindication(BSC6900,BSC6910) is set to BSICINIT_AND_RECONFIRM, both


initial BSIC verification and BSIC re-verification are required.

If PSBSICVerifyindication(BSC6900,BSC6910) is set to BSICINIT, only initial BSIC verification


is required.

If PSBSICVerifyindication(BSC6900,BSC6910) is set to BSICINIT_ADPT, initial BSIC


verification is dynamically performed depending on whether the BCCHs of any two inter-RAT
neighboring cells use the same ARFCN. BSIC re-verification is not performed.

The cell-level
parameters CSBSICVerifyindication(BSC6900,BSC6910) and PSBSICVerifyindication(BSC6900,BSC
6910) are available in the ADD UCELLINTERRATHOCOV andMOD
UCELLINTERRATHONCOV commands. The meanings of the cell-level parameters are the same as
those of the RNC-level parameters. When both the cell- and RNC-level parameters are set, the cell-level
parameters prevail.

5.2.8 Inter-Frequency Measurements in Batches


As stipulated in 3GPP specifications, a UE can measure only two frequencies belonging to other
frequency bands at a time. If the inter-frequency neighboring cells operate at more than two frequencies,
turn on Interfreqmcmode(BSC6900,BSC6910) to support inter-frequency measurements in batches.
When Interfreqmcmode(BSC6900,BSC6910) is turned on, frequencies belonging to other frequency
bands are listed. The RNC selects target neighboring cells to be measured in the same way as that
described in section 5.2.4 Neighboring Cells to Be Measured. The RNC sends the UE information about
the neighboring cells operating on the first two frequencies. If no inter-frequency neighboring cell meets
the required conditions and Interfreqmcmode(BSC6900,BSC6910) expires, the RNC sends a
measurement control message to the UE, instructing the UE to stop the measurement on the specified
frequencies and start the measurement on new frequencies. If no more frequencies are to be measured,
the RNC stops compressed mode. A maximum of three batches of inter-frequency measurements are
supported, that is, a maximum of six frequencies are measured. If an inter-frequency or inter-RAT
handover is to be triggered, the UE can also measure the frequencies of inter-frequency neighboring cells
in batches. Batch measurement does not affect inter-RAT measurement.
It is recommended that you set Interfreqmcmode(BSC6900,BSC6910) to 20s so that the measurement
in other inter-frequency neighboring cells is not postponed by a long measurement period.

5.3 Coverage-based or QoS-based Handover Decision and Execution


5.3.1 Inter-Frequency Coverage-based or QoS-based Handover Decision and
Execution
After receiving a measurement report from a UE, the RNC proceeds as follows:

Periodical Measurement Report Mode


After receiving the periodical measurement report of the inter-frequency cell, the RNC starts the following
decision procedures:
1.

Decides whether both the CPICH Ec/N0 value and CPICH RSCP value of the target cell pilot
signal meet the requirement of inter-frequency handover.
The evaluation formula is listed below:
Mother_Freq + CIOother_Freq Tother_Freq + H/2
where

Mother_Freq is the CPICH Ec/N0 or CPICH RSCP measurement value of the target cell
reported by the UE. Both of the two measurement values of the inter-frequency cell must
satisfy the formula.

CIOother_Freq is the cell individual offset value of the target cell. It is equal to the sum
of CIO(BSC6900,BSC6910) and CIOOffset(BSC6900,BSC6910).

2.

Tother_Freq is the quality threshold of the cells that use the target frequencies during interfrequency handovers. For details, see the "Triggering of Event 2B" section.

H is the inter-frequency hard handover hysteresis value set through the


parameter HystForPrdInterFreq(BSC6900,BSC6910).

When InterFreqHOConsiderRTWPSw(BSC6900,BSC6910) is set to ON, the RNC checks


whether the RTWP and CPICH RSCP of a neighboring cell in the measurement report meet the
following formula: RTWP - CPICH RSCP < Target frequency uplink coverage limit threshold. If the
formula is met, the UE can perform a coverage-based inter-frequency hard handover to the
neighboring cell. When InterFreqHOConsiderRTWPSw(BSC6900,BSC6910) is set to OFF, the
RNC does not make the judgement.
The target frequency uplink coverage limit threshold is specified by bits 19 to 24 of
the RsvU32Para13 parameter in the SET UALGORSVPARA command.
The target frequency uplink coverage limit threshold is specified by
the TargetFreqUlCoverLimitThd parameter in the SET UCELLINTERFREQHOCOV command.

3.

4.

The RNC starts the hard handover time-to-trigger timer. The value of the hard handover time-totrigger timer is specified by theTimeToTrigForPrdInterFreq(BSC6900,BSC6910) parameter. The
RNC stops the timer when any of the following conditions is met:

Before the timer expires, if the RNC receives a measurement report from the UE and the
measurement report contains CPICH Ec/N0 and CPICH RSCP of a neighboring cell, the RNC
determines whether the following formula is met: Mother_Freq + CIOother_Freq < Tother_Freq - H/2. If the
formula is met, the RNC stops the timer and does not select the neighboring cell in the
measurement report as the target cell.

If the InterFreqHOConsiderRTWPSw(BSC6900,BSC6910) is set to ON, the RNC


checks whether the RTWP and CPICH RSCP of a neighboring cell meet the following
formula, RTWP-CPICH RSCP Target frequency uplink coverage limit threshold. If the
formula is met, the RNC stops the timer and does not select the neighboring cell in the
measurement report as the target cell. If
the InterFreqHOConsiderRTWPSw(BSC6900,BSC6910) is set to OFF, the RNC does not
make the judgement.

After the hard handover time-to-trigger timer expires, the RNC ranks the cells in the latest
measurement report in descending order by signal quality and selects the cell with the best signal
quality for inter-frequency handover. For example, the cell with the highest CPICH RSCP in the
latest measurement report is selected, as shown in Figure 5-2.

Figure 5-2 Selecting the cell with the highest CPICH RSCP

Event-triggered Measurement Report Mode


After receiving the event 2B measurement reports of CPICH RSCP and CPICH Ec/N0 for the interfrequency cell, the RNC starts the following procedure:
1.

Adds all the pilot cells that trigger event 2B to a cell set and arranges the cells according to the
measurement quality of CPICH_Ec/N0 in descending order.

2.

If the InterFreqHOConsiderRTWPSw(BSC6900,BSC6910) is set to ON, the RNC checks


whether the RTWP and CPICH RSCP of a neighboring cell in the measurement report meet the
following formula: RTWP - CPICH RSCP Target frequency uplink coverage limit threshold. If the
formula is met, the UE cannot perform a coverage-based inter-frequency hard handover to the
neighboring cell and the RNC deletes the neighboring cell from the cell set.

3.

Selects a cell from the cell set in sequence and instructs the UE to perform a handover to the cell.

5.3.2 3G-to-2G Coverage-based and QoS-based Handover Decision and Execution


After receiving a measurement report from a UE, the RNC proceeds as follows:

Periodical Measurement Report Mode


After receiving the periodical measurement report of GSM cells, the RNC performs the following decision
and execution procedure:
1.

Decides whether the quality of 2G cells meets the conditions of inter-RAT handover.
The evaluation formula is listed below:
Mother_RAT + CIOother_RAT Tother_RAT + H/2
where

CIOother_RAT is the cell individual offset value of the target cell. It is equal to the sum
of CIO(BSC6900,BSC6910) and CIOOffset(BSC6900,BSC6910).

Tother_RAT is the quality threshold of the cells that use the target frequencies during interRAT handovers. For details, see the "Triggering of Event 3A" section.

H is the inter-RAT handover hysteresis value set


through HystforInterRAT(BSC6900,BSC6910).

2.

Mother_RAT is the measurement result of inter-RAT handover received by the RNC.

For the PS and CS combined services, the thresholds for CS services are used.

If the conditions described in 1 are met, the RNC starts the time-to-trigger timer.
The value of the time-to-trigger timer is specified by
the TimeToTrigForVerify(BSC6900,BSC6910) parameter (with BSIC acknowledged) or
theTimeToTrigForNonVerify(BSC6900,BSC6910) parameter (with BSIC unacknowledged). If the
RNC receives a measurement report from the UE before the timer expires and the signal quality of
a neighboring cell meets the following formula, the RNC stops the timer and does not select the
neighboring cell in the measurement report as the target cell:
Mother_RAT + CIOother_RAT < Tother_RAT - H/2
When the BSICVerify(BSC6900,BSC6910) parameter is set to REQUIRED, the BSIC
acknowledged mode is used. The BSICVerify(BSC6900,BSC6910) parameter is a cell-level
parameter and also a RNC-level parameter, which is set by running the ADD
UCELLINTERRATHOCOV and SET UINTERRATHOCOV commands, respectively.

3.

After the time-to-trigger timer expires, the RNC ranks the cells in the latest measurement report in
descending order by signal quality and selects the cell with the best signal quality for inter-RAT
handover.
Before performing an inter-RAT handover, the RNC checks the signal quality of the best cell. If the
signal quality of the best cell is poor, the RNC does not trigger an inter-RAT handover. This
increases the inter-RAT handover success rate. The method of determining the signal quality of the
best cell is as follows:
The RNC checks whether the switches for reporting the signal quality of intra-frequency
neighboring cells in periodical inter-RAT measurement for a single CS service and a single PS
service, respectively, are turned on:

For a single CS service, the switch can be turned on by


selecting HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH of
theHoSwitch1(BSC6900,BSC6910) parameter in the SET
UCORRMALGOSWITCH command.

For a single PS service, the switch can be turned on by


selecting HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH of
theHoSwitch1(BSC6900,BSC6910) parameter in the SET
UCORRMALGOSWITCH command.

For CS and PS combined services, the switch is the same as that for a single CS service.
If at least one switch is turned on, the periodical inter-RAT measurement reports sent by the
UE to the RNC contain the signal quality information about the cells in the active set. The
RNC checks the signal quality of the best cell in the active set of the measurement report. If
an inter-RAT neighboring cell meets the conditions of inter-RAT handover, the RNC further
checks whether the Ec/N0 of the best cell in the active set meets the following formula:

Ec/N0 Lower Thd for Inter-RAT Intra-Frequency Handover


(UsedIRATHOLowerThdEcNo(BSC6900,BSC6910)) Ec/N0 of the best cell Ec/N0 Upper
Thd for Inter-RAT Intra-Frequency Handover
(UsedIRATHOUpperThdEcNo(BSC6900,BSC6910))
If the preceding formula is met, the RNC decides to perform an inter-RAT handover.
Otherwise, the RNC decides not to perform an inter-RAT handover. Note that the RNC needs
to send an intra-frequency neighboring cell measurement control message to the UE because
the RNC decides whether to perform an inter-RAT handover based on the signal quality of
intra-frequency neighboring cells. The size of the inter-RAT measurement report increases
when it contains the intra-frequency neighboring cell measurement result, increasing the call
drop rate.
If neither switch is turned on, the RNC selects a target cell and triggers a 3G-to-2G handover.
NOTE:
In an area where 2G and 3G networks are deployed, if the inter-RAT handover success rate is
lower than expected or if the customer is unsatisfied with the situation where the 3G network signal
quality is good enough for UEs to camp on but UEs are nevertheless handed over to the 2G
network, then:

4.

Turn on the switch for a single CS service to increase the inter-RAT handover success
rate of CS services, that is, selectHO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH of
the HoSwitch1(BSC6900,BSC6910) parameter.
Turn on the switch for a single PS service to increase the inter-RAT handover success
rate of PS services, that is, selectHO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH of
the HoSwitch1(BSC6900,BSC6910) parameter.

Select a target cell. For details, see Target Cell Selection.

Target Cell Selection


Upon receipt of the first non-blank measurement report, the RNC selects a target cell according to the
policy described in Table 5-4.
Table 5-4 Target cell selection policy

Measurement Report on
Inter-frequency neighboring UMTS cells
Neighboring GSM cells

Neighboring LTE cells

The PerfEnhanceSwitch2(BSC6900,BSC6910) parameter can be set by running the SET


UCORRMPARA command.
The priorities of neighboring cells are configured in the following ways:

The NPriority(BSC6900,BSC6910) parameter in the ADD UCELLNFREQPRIOINFO command


specifies the absolute priorities of LTE frequencies. Value 0 indicates the lowest priority, and
value 7 indicates the highest priority.

The HOPrio(BSC6900,BSC6910) parameter in the ADD U2GNCELL command specifies the


priorities of neighboring GSM cells. Value 0 indicates the highest priority, and value 7 indicates the
lowest priority. If GSM 900 MHz and GSM 1800 MHz networks are deployed in the same area and
the operator expects UEs to be preferentially handed over to the GSM 1800 MHz network, set the
priorities of neighboring GSM 1800 MHz cells to values within the range of 0 to 3 and the priorities of
neighboring GSM 900 MHz cells to values within the range of 4 to 7.

Event-triggered Measurement Report Mode


After receiving the event 3A measurement report of 2G cells, the RNC performs the following decision
and execution procedure:
1.

Puts all the 2G cells that trigger event 3A into a cell set and arranges the cells according to the
measurement quality in descending order.

2.

Selects a cell from the cell set in sequence and instructs the UE to perform a handover to the cell.

5.4 Rules for 3G-to-2G Coverage-based or QoS-based Handover


The rules for enabling the 3G-to-2G handover are based on the Service Handover Indicator and the
capability requirement. The rules vary according to the types of inter-RAT handover.

Capability Requirement
Before deciding the 3G-to-2G handover, the RNC considers 2G cell capability, service capability, and UE
capability.

2G cell capability: 2G cell capability is configured through the


parameter RatCellType(BSC6900,BSC6910). This parameter indicates whether the cell supports
the GSM, GPRS, or EDGE.

Service required capability: The Required 2G Capability (Req2GCap(BSC6900,BSC6910))


specifies the capability of 2G cells required by inter-RAT handover. This indicates whether the
service is supported by the GSM, GPRS, or EDGE.

UE capability: Upon the reception of the UE capability information message, the RNC decides
whether to start the inter-RAT measurement. The information indicates whether the UE supports the
GSM, GPRS, or EDGE.

The following table describes the impacts of different types of capability on handover decision. If the
capability of all neighboring 2G cells does not meet the requirement, the inter-RAT measurement will not
be triggered.
Table 5-5 Impacts of different types of capability on handover decision

2G Cell
Capability
EDGE

UE Capability

Service Required Capability


EDGE

GPRS

GSM

EDGE

Allowed

Allowed

Allowed

GPRS

Allowed

Allowed

Allowed

GSM

GPRS

GSM

Not allowed

Not allowed

Allowed

Not supported by Not allowed


2G

Not allowed

Not allowed

EDGE

Allowed

Allowed

Allowed

GPRS

Allowed

Allowed

Allowed

GSM

Not allowed

Not allowed

Allowed

Not supported by Not allowed


2G

Not allowed

Not allowed

EDGE

Not allowed

Not allowed

Allowed

GPRS

Not allowed

Not allowed

Allowed

GSM

Not allowed

Not allowed

Allowed

Not supported by Not allowed


2G

Not allowed

Not allowed

Service Handover Indicator


The RNC initiates the coverage-based or QoS-based UMTS-to-GSM handover only when Service
Handover Indicator is as follows:

HO_TO_GSM_SHOULD_BE_PERFORM

HO_TO_GSM_SHOULD_NOT_BE_PERFORM

The RNC triggers a service-based or load-based 3G-to-2G handover only when the Service Handover
Indicator is set to HO_TO_GSM_SHOULD_BE_PERFORM.
The IE Service Handover Indicator indicates the CN policy for the service handover to the 2G network.
This IE is indicated in the Radio Access Bearer (RAB) assignment signaling assigned by the CN, or
provided by the RNC side.
The algorithm
switch HoSwitch(BSC6900,BSC6910): HO_INTER_RAT_RNC_SERVICE_HO_SWITCH decides
whether the service attribute of inter-RAT handover is based on the RNC or the CN.

If the switch is set to ON, the service attribute of inter-RAT handover is based on the parameter
configured on the RNC side.

If the switch is set to OFF, the service attribute of inter-RAT handover is first based on the CN
when the indicator is contained in the RAB assignment signaling assigned by the CN. If the CN does
not allocate a service indicator, the service attribute of inter-RAT handover is based on the RNC
side.

Through the SHIND(BSC6900,BSC6910) parameter, the service handover indicators are set as follows:

HO_TO_GSM_SHOULD_BE_PERFORM: means that the handover to the 2G network is


performed when 2G signals are available.

HO_TO_GSM_SHOULD_NOT_BE_PERFORM: means that the handover to the 2G network is


performed when 3G signals are weak but 2G signals are strong.

HO_TO_GSM_SHALL_NOT_BE_PERFORM: means that the handover to the 2G network is not


performed even when 3G signals are weak but 2G signals are strong.

By default, the RNC does as follows:

For a UE with a single signaling RAB, the RNC supports the handover to the GSM, which is not
recommended.

For the UE accessing combined services (with CS services), the RNC sets the service handover
indicator of the UE to that of CS services, because CS services have the highest QoS priority.

For the UE accessing combined services (with only PS services), the RNC sets the service
handover indicator of the UE to that of PS services with the highest QoS priority

If the service handover indicators are not configured by the CN, each indicator can be set to the service
parameter index of a service on the RNC. Each service parameter index is the index of one typical
service RAB, which involves a set of service type, source description, CN domain ID, and maximum rate
(bit/s).

5.5 3G-to-2G NACC


This section describes the feature WRFD-02030801 NACC (Network Assisted Cell Change).
Some services have requirements for the delay. If the handover takes too long, TCP may start slowly or
data transmission of the service stream may be interrupted due to the overflow of the UE buffer. The
introduction of Network Assisted Cell Change (NACC) enables the system information exchange between
different BSSs, or between BSS and RAN. The inter-RAT handover delay, especially inter-RAT handover
delay in PS domains, can be reduced. With NACC, the SRNC requests and receives the SI/PSI from the
target BSS and the target RNC sends the UE a cell change order, which contains the GSM EDGE Radio
Access Network (GERAN) system information, when the 3G-to-2G handover in the PS domain is
triggered. The NACC process specified in TS 25.901 is shown in the following figure.
NACC process specified in the protocol

1.

The SRNC receives a measurement report from the UE and determines to reselect a GERAN cell
for the UE.

2.

The SRNC sends a RAN INFORMATION REQUEST message to the SGSN.

3.

The SGSN forwards the message to the target BSS.

4.

5.
6.

The target BSS sends a RAN INFORMATION message, which contains the SI/PSI of the
GERAN, to the SRNC through the SGSN. The RAN INFORMATION message can be sent in Ondemand mode (single report) or On-modification mode (multiple reports). In V2.1, On-demand
mode is used.
The SGSN forwards the message to the SRNC over the Iu interface.
If there are multiple messages, the SRNC terminates the reporting process by sending a
TERMINATION/END message to the SGSN.

Information can be exchanged between different BSSs or between the BSS and RAN can be
implemented by exchanging RIM messages through either the CN or Huawei proprietary eCoordinator.
NOTE:
RIM messages can be exchanged between the UTRAN and GERAN through the eCoordinator when the
following conditions are met:

Huawei devices used in the UTRAN and GERAN are connected to the same eCoordinator.

The CN to which the UTRAN and GERAN connect does not support the RIM procedure or the
RIM procedure is not enabled for the UTRAN and GERAN.

When the RIM procedure is performed through the eCoordinator, the switches for the RIM procedure
must be set to on for NEs involved in the procedure, such as BSC, eCoordinator, and RNC. Otherwise,
the RIM procedure cannot be performed through the eCoordinator and these NEs cannot send RIM
messages to or respond to RIM messages from the CN.

With NACC, the RNC sends a cell change order carrying the SI/PSI of the GERAN to the UE when a
UMTS-to-GSM handover is triggered. To enable the NACC function, do as follows:

Run the SET UCORRMALGOSWITCH command to


set HoSwitch(BSC6900,BSC6910): HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH to
ON.

Run the ADD UEXT2GCELL or MOD UEXT2GCELL command to


set SuppRIMFlag(BSC6900,BSC6910) to TRUE.

(Optional) Select the RIM_ON_ECO_SWITCH check box under


the PROCESSSWITCH5(BSC6900,BSC6910) parameter in the SET URRCTRLSWITCH command
when the RIM procedure is performed through the eCoordinator.

5.6 3G-to-2G PS Handover


This section describes the feature WRFD-02030802 PS Handover between UMTS and GPRS
PS handover is similar to the inter-RAT handover in the CS domain.
If the HoSwitch(BSC6900,BSC6910): HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH is turned
on, the PS handover from the 3G network to the 2G network is performed in the relocation process. When
the switch is not on, the PS handover from the 3G network to the 2G network is performed in the cell
change order process.
To enable the PS HO function, do as follows:

Run the SET UCORRMALGOSWITCH command to


set HoSwitch(BSC6900,BSC6910): HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH parame
ter to ON.

Run the ADD UEXT2GCELL or MOD UEXT2GCELL command to


set SuppPSHOFlag(BSC6900,BSC6910) to TRUE.

5.7 2G-to-3G Handover


The 2G-to-3G handover is initiated by the 2G network, where the dual-mode (GSM and WCDMA) mobile
terminals are required. Both the GSM MSC and the GSM BSS must support the GSM-to-UMTS handover.

5.8 System Processing After a Handover Failure


5.8.1 Inter-Frequency Handover Failure
If an inter-frequency handover fails, the RNC performs different operations on CS and PS UEs:

For a UE that is processing CS services, the RNC enables the UE to continue processing the CS
services in the source cell only if theAMR_HHO_FAIL_ROLLBACK_SWITCH check box under
the PROCESSSWITCH4(BSC6900,BSC6910) parameter in the SET URRCTRLSWITCH command
is selected.

For a UE that is processing PS services, the RNC unconditionally enables the UE to continue
processing the PS services in the source cell.

If an inter-frequency handover fails, the RNC takes the following measures:

The RNC starts a penalty timer specified by


the PenaltyTimerForIFHoFail(BSC6900,BSC6910) parameter. During the penalty period, the RNC
prohibits the UE from being handed over to the target cell again. If this parameter is set to 0, the
RNC does not impose a penalty on the target cell.

If the number of consecutive inter-frequency handover failures for a UE reaches the value of
the IFHoFailNum(BSC6900,BSC6910) parameter, the RNC imposes a penalty on the UE. During
the penalty period specified by the UEPenaltyTimerForIFHoFail(BSC6900,BSC6910) parameter,
the RNC prohibits the UE from initiating inter-frequency handovers. If this parameter is set to 0, the
RNC does not impose a penalty on the UE.

5.8.2 Inter-RAT Handover Failure


If an inter-RAT handover fails, the RNC also performs different operations on CS and PS UEs: For UEs
that are processing CS services:
Upon receipt of a HANDOVER FROM UTRAN FAILURE message from the UE, the RNC performs the
following operations:

Terminates the handover procedure and enables the UE to continue processing the CS services
in the source cell.

Starts a penalty timer. During the penalty period, the RNC prohibits the UE from being handed
over to the target cell again.
If the PERFENH_INTERRAT_PENALTY_50_SWITCH check box under
the PerfEnhanceSwitch(BSC6900,BSC6910) parameter in the SET UCORRMPARA command is
selected, the penalty duration is 50s. Otherwise, the penalty duration is 30s.

If the number of handover failures caused by physical channel failures reaches the value of
the InterRatPhyChFailNum(BSC6900,BSC6910) parameter, the RNC starts another penalty timer.
During the penalty period specified by
the PenaltyTimeForPhyChFail(BSC6900,BSC6910) parameter, the UE is prohibited from being
handed over to any neighboring GSM cell. The IRATHO.FailOutCS.PhyChFail counter provides the
number of handover failures.
The InterRatPhyChFailNum(BSC6900,BSC6910) and PenaltyTimeForPhyChFail(BSC6900,BSC
6910) parameters are set by running the cell-level command ADD UCELLINTERRATHOCOV or
RNC-level command SET UINTERRATHONCOV.

For UEs that are processing PS services:


Upon receipt of a CELL CHANGE ORDER FROM UTRAN FAILURE message from the UE, the
RNC performs the following operations:

Terminates the handover procedure and enables the UE to continue processing the PS
services in the source cell.

Starts a penalty timer. During the penalty period, the RNC prohibits the UE from being
handed over to the target cell again.
If the PERFENH_INTERRAT_PENALTY_50_SWITCH check box under
the PerfEnhanceSwitch(BSC6900,BSC6910) parameter in the SET
UCORRMPARAcommand is selected, the penalty duration is 50s. Otherwise, the penalty
duration is 30s.

If the number of handover failures caused by physical channel failures reaches the value of
the InterRatPhyChFailNum(BSC6900,BSC6910) parameter, the RNC starts another penalty timer.
During the penalty period specified by the PenaltyTimeForPhyChFail(BSC6900,BSC6910) parameter,
the UE is prohibited from being handed over to any neighboring GSM cell. The
IRATHO.FailOutPSUTRAN.PhyChFail counter provides the number of handover failures.

6 Non-Coverage-based Handover
Non-coverage-based handover consists of load-based handover and service-based handover:

Load-based handover can be further classified into two types:

Load-based inter-frequency handover. For details, see section 6.1 Load-based InterFrequency Handover.

Load-based inter-RAT handover. For details, see section 6.2 Load-based Inter-RAT
Handover.

Service-based handover can be further classified into two types:

Service-based inter-frequency handover. For details, see the "Inter-Frequency DRD for
Service Steering" section in Directed Retry Decision Feature Parameter Description.

Service-based inter-RAT handover. For details, see section 6.3 Service-based Inter-RAT
Handover.

6.1 Load-based Inter-Frequency Handover


6.1.1 Load-based Inter-Frequency Handover Procedure
The load-based inter-frequency handover suits co-sited cells covering the same area.

In the triggering phase


The Load Reshuffling (LDR) module detects that the current cell is in basic congestion and then
initiates an inter-frequency handover.

In the decision phase


For a load-based inter-frequency blind handover, the RNC decides to trigger an inter-frequency blind
handover if the corresponding conditions are met.
For a load-based inter-frequency handover based on periodical measurement, the RNC requests
the UE to perform the inter-frequency measurement. Based on the measurement results, the RNC
chooses a target cell to perform inter-frequency hard handover.

In the execution phase


The RNC performs the handover according to the decision result.

For details of LDR, see Load Control Feature Parameter Description.

6.1.2 Load-based Inter-Frequency Handover Measurement


The load-based inter-frequency handover uses the periodical report mode.

In a load-based inter-frequency blind handover, CPICH RSCP of the used frequency is


measured.

In a load-based inter-frequency measurement-based handover, both CPICH_RSCP and


CPICH_Ec/N0 of the target frequency are measured.

6.1.3 Load-based Inter-Frequency Handover Decision and Execution


The LDR algorithm may trigger an inter-frequency handover. The following describes the procedure for
handover decision and execution.
The load-based inter-frequency handover can be performed based on blind handover or measurement
that can be decided by the parameterInterFreqLDHOMethodSelection(BSC6900,BSC6910).

Load-based Inter-Frequency Blind Handover

The procedure for load-based inter-frequency blind handover decision is as follows:


1.

The LDR algorithm learns that a cell is in basic congestion and provides target cells and the UE
with low priority for handover.

2.

The RNC determines to trigger an inter-frequency blind handover.

If the UE is not in the soft handover state, the RNC directly performs a load-based inter-frequency blind
handover.
If the UE is in the soft handover state, the RNC performs based on the following conditions:

If the HoSwitch(BSC6900,BSC6910): HO_ALGO_LDR_ALLOW_SHO_SWITCH is set to ON,


The RNC determines whether the cell that triggers LDR is the best cell.

If this cell is the best cell, the RNC initiates an intra-frequency measurement for loadbased inter-frequency blind handover. For details, see the section "Intra-frequency
Measurement Triggered by Load-based Inter-Frequency Blind Handover." The intra-frequency
measurement is used to estimate quality of the inter-frequency neighboring cell of the same
coverage and to increase the success rate of inter-frequency blind handovers.

If this cell is not the best cell, the RNC does not initiate a load-based inter-frequency blind
handover.

If the HoSwitch(BSC6900,BSC6910): HO_ALGO_LDR_ALLOW_SHO_SWITCH is set to OFF,


the RNC determines whether the UE is in the soft handover state:

If the UE is in the soft handover state, the RNC does not trigger a load-based interfrequency blind handover.

If the UE is not in the soft handover state, the RNC initiates an intra-frequency
measurement for a load-based inter-frequency blind handover. For details, see the "Intrafrequency Measurement Triggered by Load-based Inter-Frequency Blind Handover" section.
The purpose of the measurement is to evaluate the signal quality of co-coverage interfrequency neighboring cells using the signal quality of intra-frequency cells. This increases the
success rate of inter-frequency blind handovers.

Intra-frequency Measurement Triggered by Load-based Inter-Frequency Blind Handover


The inter-frequency cells with the same coverage area have the same CPICH RSCP values. By
measuring the CPICH RSCP of the serving cell, the RNC obtains quality of the cells with the same
coverage area and determines whether to allow a blind handover, which increases the probability of
successful blind handover.
1.
2.

The RNC initializes the timer of intra-frequency measurement for blind handover. The timer is
specified by internal algorithm and does not need to be configured.
The RNC initiates a periodical intra-frequency measurement.
The measurement report mode is set to periodical report.

The reporting period is BlindHOIntrafreqMRInterval(BSC6900,BSC6910).


The number of measurement reports
is BlindHOIntrafreqMRAmount(BSC6900,BSC6910).

The intra-frequency handover measurement quantity is CPICH RSCP.

The list of measured cells contains only the cells that trigger LDR.

3.

After receiving from the UE the intra-frequency measurement reports for conditional blind
handover, the RNC checks whether the following condition is met:
CPICH RSCP of the cell in the measurement report
BlindHOQualityCondition(BSC6900,BSC6910)

4.

If the condition is met, the RNC increments the counter of the number of intra-frequency
measurement reports for blind handover by 1.

If the condition is not met, the RNC does not perform a blind handover to the cell that
triggers LDR and stops intra-frequency measurement for blind handover.

When the counter reaches the value of BlindHOIntrafreqMRAmount(BSC6900,BSC6910), the


RNC initiates a blind handover to the target cell.
If the counter does not reach this value, the RNC waits for the next intra-frequency measurement
report from the UE.

5.

If the timer of intra-frequency measurement for blind handover expires, the RNC does not perform
a blind handover to the target cell and stops intra-frequency handover measurement for blind
handover.

If the inter-frequency handover based on coverage or QoS is triggered, the RNC stops the intra-frequency
measurement for conditional blind handover.

Load-based and Measurement-based Inter-Frequency Handover Decision and Execution


1.

The LDR algorithm learns that a cell is in basic congestion and provides target cells and the UE
with low priority for handover.

2.

The RNC selects the target cell based on the measurement results. The report period is specified
by the parameter PrdReportInterval(BSC6900,BSC6910).
The target cell must meet the following conditions:

The CPICH RSCP value of the target cell is larger


than TargetFreqThdRscp(BSC6900,BSC6910).

The CPICH Ec/N0 value of the target cell is larger


than TargetFreqThdEcN0(BSC6900,BSC6910)

The target cell is not in the basic congestion state.

The RNC performs an inter-frequency hard handover to the target cell directly.

6.2 Load-based Inter-RAT Handover


6.2.1 Load-based Inter-RAT Handover Procedure
When the load of the 3G network is heavy and all the RABs of the UE are supported by the 2G network,
the load-based inter-RAT (3G-to-2G) handover (WRFD-020306 Inter-RAT Handover Based on Load) is
triggered.

Figure 6-1 Load-based Inter-RAT handover procedure

In the triggering phase


When the load of the 3G cell that the UE accesses is higher than the related threshold, the Load
Reshuffling (LDR) algorithm makes a handover decision. For detailed information of the LDR, see
Load Reshuffling in the Load Control Feature Parameter Description.

In the measurement phase


The RNC enables the compressed mode and starts the inter-RAT handover measurement.

In the decision phase


After the UE reports event 3C, the RNC makes a handover decision.

In the execution phase


The RNC initiates a handover procedure.

6.2.2 Load-based Inter-RAT Handover Measurement


For a load-based Inter-RAT handover, the measurement report is triggered only by event. In a load-based
inter-RAT handover, event 3C takes only GSM RSSI as measurement quantity. When the estimated
quality of other system is higher than a certain threshold, the UE reports event 3C to the RNC.
When the conditions for event 3C are met and the delay requirement specified by
the TrigTime3C(BSC6900,BSC6910) parameter can be satisfied, the UE sends the measurement report
of event 3C.
Event 3C is triggered on the basis of the following formula:
MOtherRAT + CIOOtherRAT TOtherRAT + H3c/2
where

MOtherRAT is the measurement value of the cell (in another RAT) in the reporting range.

CIOOtherRAT is the cell individual offset value of the cell (in another RAT) in the reporting range,
which is equal to the sum of CIO(BSC6900,BSC6910) andCIOOffset(BSC6900,BSC6910).

TOtherRAT is the absolute inter-RAT handover threshold. Based on different service types (CS, PS
domain R99 services, or PS domain HSPA services), this threshold can be configured through the
following parameters:

InterRATNCovHOCSThd(BSC6900,BSC6910)

InterRATNCovHOPSThd(BSC6900,BSC6910)

H3c is HYSTFOR3C(BSC6900,BSC6910), the hysteresis value of event 3C.

For the PS and CS combined services, the thresholds for CS services are used.

6.2.3 Load-based Inter-RAT Handover Decision and Execution


After receiving the event 3C measurement report of 2G cells, the RNC performs the following decision
and execution procedure:
1.
2.

Puts all the 2G cells that trigger event 3C into a cell set and arranges the cells according to the
measurement quality in descending order.
Selects the cells in sequence from the cell set.

To avoid the impact of the UE (in long-term measurement of compressed mode) on the radio network, the
parameter InterRATHOAttempts(BSC6900,BSC6910) is set to restrict the maximum attempts of the 3Gto-2G load-based or service-based handover. The parameter indicates the handover attempts made to
the same cell or different cells. If the number of attempts exceeds the parameter value, the RNC does not
initiate the handover.

6.3 Service-based Inter-RAT Handover


Service-based inter-RAT handover supports 3G-to-2G handover based on service attributes. When 3G
and 2G networks coexist, this feature enables the 3G traffic to be directed to the 2G network.
This feature can balance the load between the two systems by transferring some kind of appropriate
services to GSM/GPRS.

6.3.1 Switches for Service-based Inter-RAT Handover


To perform the service-based 3G-to-2G handover, the RNC must turn on the related switches for services
in the CS and PS domains.

When a single CS service is initially set up by the UE, the RNC allows the 3G-to-2G servicebased handover if CSServiceHOSwitch(BSC6900,BSC6910) is set to ON.

When a single PS service is initially set up by the UE, the RNC allows the service-based 3G-to2G handover if PSServiceHOSwitch(BSC6900,BSC6910) is set to ON.

For the combined services, no service-based handover is triggered.

6.3.2 Service-based Inter-RAT Handover Procedure

Figure 6-2 Service-based 3G-to-2G handover procedure

Except for the triggering phase, the procedure of service-based inter-RAT handover is the same as that of
the Load-based inter-RAT handover. For details, see section 6.2.3 Load-based Inter-RAT Handover
Decision and Execution.
When a service is established, the RNC requests the handover to the GSM based on the service type and
service handover indicator assigned by the CN.
Figure 6-3 shows an example of rules for the indicator of the 3G-to-2G handover based on load and
service.

Figure 6-3 Example of rules for indicator of 3G-to-2G handover based on load and service

6.4 Rules for Enabling Load-based or Service-based Inter-RAT Handover


The RNC initiates the 3G-to-2G load handover only when Service Handover Indicator
(SHIND(BSC6900,BSC6910)) is as follows:

HO_TO_GSM_SHOULD_BE_PERFORM

HO_TO_GSM_SHOULD_NOT_BE_PERFORM

The RNC initiates the service-based 3G-to-2G handover only when the Service Handover Indicator is
HO_TO_GSM_SHOULD_BE_PERFORM.
Before deciding the 3G-to-2G handover, the RNC considers 2G cell capability
(RatCellType(BSC6900,BSC6910)), service required capability (Req2GCap(BSC6900,BSC6910)) and
UE capability.
The following table describes the impacts of different types of capability on handover decision.
Table 6-1 Impacts of different types of capability on handover decision

Cell Capability

EDGE

UE Capability

Service Capability (Required by 2G)


EDGE

GPRS

GSM

EDGE

Allowed

Allowed

Allowed

GPRS

Not allowed

Allowed

Allowed

GSM

Not allowed

Not allowed

Allowed

Not supported by Not allowed

Not allowed

Not allowed

2G
GPRS

GSM

EDGE

Not allowed

Allowed

Allowed

GPRS

Not allowed

Allowed

Allowed

GSM

Not allowed

Not allowed

Allowed

Not supported by Not allowed


2G

Not allowed

Not allowed

EDGE

Not allowed

Not allowed

Allowed

GPRS

Not allowed

Not allowed

Allowed

GSM

Not allowed

Not allowed

Allowed

Not supported by Not allowed


2G

Not allowed

Not allowed

If the capability of all neighboring 2G cells does not meet the requirement, the inter-RAT measurement
will not be triggered.

6.5 Interchanging Inter-RAT Load Information


In a load-based or service-based inter-RAT handover, load information is interchanged between 2G and
3G networks to facilitate inter-RAT handover (WRFD-020310 3G/2G Common Load Management).
The load status between the source cell and the target cell can be acquired by interchanging load
information between a 3G cell and a 2G cell during the load-based or service-based handover. Whether
to further conduct the handover can be determined to avoid the 2G cell overload and possible handovers
to congested cells.

Interchanging Load Information in 3G-to-2G Handover

The procedure for load information interchanging between the source 3G cell and target 2G cell
is described as follows:
1.

When the RNC sends a RELOCATION REQUIRED message to the 3G CN,


If the switch SndLdInfo2GsmInd(BSC6900,BSC6910) is set to ON, the RELOCATION
REQUIRED message includes the Old BSS To New BSS Information IE that includes the load
information of the 3G source cell.
If the switch SndLdInfo2GsmInd(BSC6900,BSC6910) is set to OFF, then the RELOCATION
REQUIRED message does not include the Old BSS To New BSS Information IE.

2.

When the RNC receives the RELOCATION COMMAND message from the 2G CN,
If the switch NcovHoOn2GldInd(BSC6900,BSC6910) is set to ON, the RNC obtains the load
information of the 2G target cell by reading the Inter-System Information Transparent Container IE,
which is included in the RELOCATION COMMAND message.

If the 2G load is lower than CSHOOut2GloadThd(BSC6900,BSC6910) (for CS service),


or if the 2G load is lower than PSHOOut2GloadThd(BSC6900,BSC6910)(for PS service), the
RNC continues the inter-RAT handover procedure; otherwise, the RNC returns the Relocation
Cancel message to the CN to cancel this inter-RAT handover and makes another handover
attempt to the next candidate cell generated in the cell list based on inter-RAT measurement.

If the Inter-System Information Transparent Container IE, is not included in the


RELOCATION COMMAND message, the load information of the 2G target cell is not
considered and this inter-RAT handover is continued.
If the switch NcovHoOn2GldInd(BSC6900,BSC6910) is set to OFF, the RNC continues the
inter-RAT handover procedure without considering the thresholds.

Interchanging Load Information in 2G-to-3G Handover

In 2G-to-3G handover based on load or service, the RNC can make an admission decision
considering the load information of the 3G target cell. This can avoid the worsening of the 3G
system performance caused by 2G-to-3G handover based on the load or service if the 3G system
load is high.
The procedure is described as follows:
1.

2.
3.

When the RNC sends a RELOCATION REQUEST ACKNOWLEDGE message to the 3G CN,

If the switch SndLdInfo2GsmInd(BSC6900,BSC6910) is set to ON, the RELOCATION


REQUEST ACKNOWLEDGE message includes the New BSS To Old BSS Information IE,
which includes the load information of the 3G target cell.

If the switch SndLdInfo2GsmInd(BSC6900,BSC6910) is set to OFF, the RELOCATION


REQUEST ACKNOWLEDGE message does not include the New BSS To Old BSS
Information IE.

Depending on the network requirement, the 2G network decides whether to use the load
information sent to the 3G network for judgment.
When the RNC receives the RELOCATION REQUEST message from the 3G CN,

If the 3G cell is not in the basic congestion state, the RNC continues the inter-RAT
handover procedure.

If the 3G cell is in the basic congestion state, the RNC returns RELOCATION FAILURE
message to the CN to cancel the inter-RAT handover.

NOTE:
For the concept of "basic congestion", see Load Control Feature Parameter Description.

7 HSPA Handover
7.1 HSDPA Handover
This section describes the WRFD-01061006 HSDPA Mobility Management feature.

7.1.1 HSDPA Intra-Frequency Handover


This section describes the decision and execution of intra-frequency handover, and the handover
between a cell that supports the F-DPCH and a cell that does not support the F-DPCH after the
introduction of HSDPA.

Handling of Event 1A
After receiving an event 1A report, the RNC proceeds as follows:

If the number of cells in the active set does not reach the maximum value, the RNC adds the cell
to the active set.

If the number of cells in the active set reaches the maximum value, the RNC does not add the
radio link to the active set.

Handling of Event 1B
After receiving an event 1B report, the RNC determines whether to delete a cell.

If the cell to be deleted is not an HSDPA serving cell, the cell is directly removed.

If the cell to be deleted is an HSDPA serving cell, then:

If the new best cell supports HSDPA, the new best cell is reconfigured to be an HSDPA
serving cell. If the reconfiguration fails, the service is reconfigured onto DPCH.

If the new best cell does not support HSDPA, the service is reconfigured onto DPCH to
ensure the continuity of the service.

Handling of Event 1C
After receiving an event 1C report, the RNC decides whether to change the worst cell.

If the cell to be replaced is not an HSDPA serving cell, the cell is directly removed.

If the cell to be replaced is an HSDPA serving cell, then:

If the best cell supports HSDPA, the best cell is reconfigured to be an HSDPA serving
cell. If the reconfiguration fails, the service is reconfigured onto DPCH.

If the best cell does not support HSDPA, the service is reconfigured onto DPCH to ensure
the continuity of the service.

Handling of Event 1D
After receiving an event 1D report, the RNC proceeds as follows:

If the downlink service is carried on the HSDPA, then:

If the new best cell in the active set supports HSDPA and the HSPA hysteresis timer
(HspaTimerLen(BSC6900,BSC6910)) expires, the new best cell is reconfigured to be an
HSDPA serving cell.

If the new best cell in the active set does not support HSDPA, the downlink service is
directed to the DCH through the reconfiguration.
Figure 7-1 shows an example of how to handle event 1D in this situation. Assume that the UE
moves from HSDPA cell 1 to HSDPA cell 2, that the two cells are intra-frequency neighboring
cells, and that all the cells in the active set support HSDPA. The RNC updates the HSDPA
serving cell according to the reported event and keeps the HSDPA serving cell consistent with
the best cell.

Figure 7-1 Intra-frequency handover between HSDPA cells when the best cell changes

If the downlink service is carried on the DCH, then:


The UE is handover to the target cell, and the service is carried on DCH. After handover, the RNC
may retry to configure the service on HS-DSCH. For details, see 7.5 HSPA Retry.

In the execution procedure mentioned above, CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH of


theCmpSwitch(BSC6900,BSC6910)parameter is used to determine whether the update of the active set
and the change of the serving cell are synchronized. This switch is applicable to only R6 UEs.

If the switch is ON, the UE supports the synchronization of the update of the active set and the
change of the serving cell.

If the switch is OFF, the UE reconfigures the change of the serving cell by allocating physical
channels after updating the active set.

During the update of the HSDPA serving cell, set


the NBMMachsResetAlgoSelSwitch(BSC6900,BSC6910) parameter to determine whether to reset the
UE MAC-hs.
RAN16.0 introduces the fast HSDPA serving cell change function, which is implemented during an
HSDPA intra-frequency handover. For details about the fast HSDPA serving cell change function,
see Process Optimization Feature Parameter Description.

Handling of HSDPA Serving Cell Uplink Out-Of-Synchronization


If experiencing uplink out-of-synchronization, the HSDPA serving cell is changed and its serving link is
removed when the link restoration timer (RlRstrTmr(BSC6900,BSC6910)) expires.
The RESERVED_SWITCH_1_BIT29 switch under RsvSwitch1(BSC6900,BSC6910) in the SET
UALGORSVPARA command controls whether a cell change to the HSDPA target cell is allowed if the
HSDPA target cell is in uplink out-of-synchronization state.

When the switch is turned on, the cell change is prohibited.

When the switch is turned off, the cell change is allowed.

7.1.2 HSDPA Inter-Frequency Handover


Inter-frequency handover can be triggered on the basis of coverage, load, and hierarchical cell structure
(HCS).
The following describes the three possible scenarios in which an inter-frequency handover occurs.

Scenario 1: Inter-Frequency Handover from an HSDPA Cell to an R99 Cell

As shown in Figure 7-2, when the UE moves from cell 1 (an HSDPA cell) to cell 2 (an R99 cell),
the inter-frequency handover conditions are met and event 2B is triggered. The RNC makes a
handover decision for HSDPA services according to the neighboring cell measurement report,
and reconfigures the service onto the DPCH of cell 2.
Figure 7-2 Inter-frequency handover from an HSDPA cell to an R99 cell

Scenario 2: Inter-Frequency Handover from an R99 Cell to an HSDPA Cell

As shown in Figure 7-3 when the UE moves from cell 2 (an R99 cell) to cell 1 (an HSDPA cell),
the inter-frequency handover conditions are met and event 2B is triggered. The RNC hands over
the UE to the DPCH first, and then to the HS-PDSCH if the service can be carried on the HSPDSCH.

Figure 7-3 Inter-frequency handover from an R99 cell to an HSDPA cell

Scenario 3: Inter-Frequency Handover Between HSDPA Cells

As shown in Figure 7-4 when the UE moves from cell 1 (an HSDPA cell) to cell 2 (an HSDPA
cell) and the inter-frequency handover conditions are met, the UE is handed over from cell 1 to
cell 2. The target cell becomes the new serving HS-PDSCH cell.
If the serving or target cell is in load congestion when the UE performs a serving cell update for
inter-frequency or inter-RAT handover, the service is reconfigured from the HS-PDSCH to the
DPCH.
The hard handovers of an HSDPA cell are the same as those of an R99 cell.

Figure 7-4 Inter-frequency handover between HSDPA cells

7.1.3 HSDPA Inter-RAT Handover


When the UE is handed over to a cell that supports the F-DPCH from another system and a UL or DL
event 4A is reported, the RNC decides whether to change the bearer mode of TRB and SRB.
If the TPC command is carried on the F-DPCH between the UE and the UTRAN, the SRB and the TRB
are carried on the HS-DSCH. If a cell that does not support the F-DPCH is added to the active set, all the
F-DPCHs are deleted. In addition, new DPCHs between the UE and all the cells in the active set are set
up to carry the SRB and TPC commands.

7.2 HSUPA Handover


This section involves the feature "WRFD-01061204 HSUPA Mobility Management".

7.2.1 HSUPA Intra-Frequency Handover


This section describes the decision and execution procedure of intra-frequency handover, and the
handover between E-DCHs of 10 ms TTI and 2 ms TTI after the introduction of HSUPA.

Handling of Event 1A

After receiving the measurement report, the RNC proceeds as follows:


If the target cell supports HSUPA and the uplink service is carried on the E-DCH, then:

If the current number of cells in the E-DCH active set is smaller than the value
of MaxEdchCellInActiveSet(BSC6900,BSC6910), the target cell is added to both the DCH and EDCH active sets.
Otherwise, the target cell is added to only the DCH active set.

After deciding that a cell can be added to the E-DCH active set,

If the admission in the downlink fails, the cell is added to neither the E-DCH active set nor the
DCH active set. It waits for the next event 1A report for retry.

Otherwise, if the admission in the downlink succeeds, the RNC perform the HSUPA admission in
the uplink.

If HSUPA admission in the uplink succeeds, the cell is added to the E-DCH active set and
the DCH active set.

If HSUPA admission in the uplink fails, the cell is added only to the DCH active set. If the
DCH admission in the uplink still fails, the cell is added to neither the E-DCH active set nor the
DCH active set. It waits for the next event 1A report for retry.

Handling of Event 1B

If the number of radio links in the DCH active set is larger than one, then:

If the cell to be removed is not an HSUPA serving cell, the cell is directly removed.

If the cell to be removed is an HSUPA serving cell, then:

If the new best cell supports HSUPA, the new best cell is reconfigured to be an E-DCH
serving cell.

If the new best cell does not support HSUPA, the uplink service is redirected to the DCH
through the RB reconfiguration.

If the current service is CS Voice over HSPA and the cell to be removed is an E-DCH serving cell,
then:

If the new best cell supports both HSDPA and HSUPA, the cell is reconfigured to be an
HS-DSCH serving cell or an E-DCH serving cell.

If the new best cell supports HSDPA but not HSUPA, the current service is changed from
CS Voice over HSPA to CS Voice over DCH. If there remain other HSDPA services, the serving
cell should be updated and the new best cell should be the HS-PDSCH serving cell.

If the new best cell supports neither HSUPA nor HSDPA, the current service is
reconfigured to be CS Voice over DCH.

Whether the cells under the adjacent RNC support CS Voice over HSPA is determined by the
RNC-level parameter CSVoiceoverHSPASuppInd(BSC6900,BSC6910).
After the best cell of a UE changes, if the size of the DCH or E-DCH active set of the new best
cell is different from those of the old best cell, the RNC removes or reconfigures radio links to
adapt to the size and configuration of the new best cell.
Handling of Event 1C

When event 1C is triggered, the UE reports the event-triggered list that contains good cells and
the cells to be replaced, and sequences the cells from the highest to the lowest quality according
to measurement quantity.
After receiving the measurement report, the RNC proceeds as follows:

If the new cell supports HSUPA, then:

If the current number of cells in the E-DCH active set is smaller than the value
of MaxEdchCellInActiveSet(BSC6900,BSC6910), the new cell is added to the E-DCH active
set.

If the current number of cells in the E-DCH active set is equal to the value
of MaxEdchCellInActiveSet(BSC6900,BSC6910) and the cell to be replaced is also included
in the E-DCH active set, the new cell joins the E-DCH active set through replacement.

If the current number of cells in the E-DCH active set is equal to the value
of MaxEdchCellInActiveSet(BSC6900,BSC6910) and the cell to be replaced is not included
in the E-DCH active set, the new cell is added only to the DCH active set.

If the current service is CS Voice over HSPA and the cell to be removed is an E-DCH serving cell,
then:

If the new best cell supports both HSDPA and HSUPA, the cell is reconfigured to be an
HS-DSCH serving cell or an E-DCH serving cell.

If the new best cell supports HSDPA but not HSUPA, the current service is changed from
CS Voice over HSPA to CS Voice over DCH through the reconfiguration. If there remain other
HSDPA services, the serving cell should be updated and the new best cell should be the HSPDSCH serving cell.

If the new best cell supports neither HSUPA nor HSDPA, the current service is
reconfigured to be CS Voice over DCH. If the cell to be removed is an E-DCH serving cell, the
HS-DSCH serving cell must be removed at the same time. Therefore, a new E-DCH serving
cell or HS-DSCH serving cell must be determined. The method is the same as that of removing
the serving cell, as described in the previous section of Handling of Event 1B.

If the new cell does not support HSUPA, the cell is added to only the DCH active set.
Handling of Event 1D

If the criteria for intra-frequency hard handover are fulfilled, the RNC performs intra-frequency
hard handover after receiving the event 1D report. If the criteria for intra-frequency hard
handover are not fulfilled, the RNC performs intra-frequency soft handover based on the
measurement report.
If the uplink service is carried on the E-DCH, then:

If the new best cell in the active set supports HSUPA and the HSPA hysteresis timer
(HspaTimerLen(BSC6900,BSC6910)) expires, the E-DCH serving cell becomes the best cell. The
HSPA hysteresis timer is restarted after the cell change.

If the new best cell in the active set does not support HSUPA,

The uplink service is directed to the DCH through the reconfiguration. If the
reconfiguration fails, the service is still carried on the E-DCH. The UE is connected to the new
best cell only on the DCH.

If the uplink service is carried on the DCH, then:

The uplink service is still carried on the DCH. After handover, the RNC may retry to configure the
service on E-DCH. For details, see 7.5 HSPA Retry.

If the current service is CS Voice over HSPA, then:

If the new best cell supports both HSUPA and HSDPA, the cell is reconfigured to be an HSPA
serving cell.

Otherwise, the service is changed from CS Voice over HSPA to CS Voice over DCH through the
reconfiguration.

Triggering of Event 1J

Event 1J is triggered under the following condition:


10 x Log (MNew) + CIONew 10 x Log (MInAS) + CIOInAS + H1j/2

MNew is the measurement result of the cell not in the E-DCH active set but in the DCH active set.

CIONew and CIOInAS refer to the offset of each cell.

MInAS is the measurement result of the cell in the E-DCH active set with the lowest measurement
result.

H1J is the hysteresis parameter for event 1J and is determined


by Hystfor1J(BSC6900,BSC6910).

If the measurement result is CPICH-Ec/N0, MNew and MInAS are expressed as ratios.

If the measurement result is CPICH-RSCP, MNew and MInAS are expressed in mW.
Figure 7-5 Triggering of event 1J

A: signal quality curve of a cell in the E-DCH active set

B: signal quality curve of the worst cell in the E-DCH active set

C: signal quality curve of a cell not in the E-DCH active set but included in DCH active set

D: signal quality curve of a cell not in the E-DCH active set but included in DCH active set

In Figure 7-5, the hysteresis and the cell individual offsets for all cells equal 0.

The first measurement report is sent when primary CPICH D becomes better than primary
CPICH B. The "cell measurement event result" of the measurement report contains the
information of primary CPICH D and CPICH B.
On the assumption that the E-DCH active set has been updated after the first measurement report
(E-DCH active set is now primary CPICH A and primary CPICH D), the second report is sent
when primary CPICH C becomes better than primary CPICH A. The "cell measurement event
result" of the second measurement report shows that primary CPICH C is better than primary
CPICH A in quality.
The following parameters need to be set on the RNC LMT:

Hystfor1J(BSC6900,BSC6910): hysteresis of event 1J

TrigTime1J(BSC6900,BSC6910): time to trigger event 1J

PeriodMRReportNumfor1J(BSC6900,BSC6910): number of periodic reports for event 1J

ReportIntervalfor1J(BSC6900,BSC6910): report interval for event 1J after change to the


periodic report

HoSwitch(BSC6900,BSC6910): HO_INTRA_FREQ_RPRT_1J_SWITCH: measurement control


switch for event 1J. When the switch is ON, the UE version is R6 and event 1J is included in the
intra-frequency measurement control message.

After receiving the intra-frequency measurement report from the UE, the RNC decides whether
to go to the execution phase, depending on the information in the report.
Handling of Event 1J

Event 1J provides the solution to the issue of how to add an HSUPA cell in a DCH active set to
an E-DCH active set. This event is triggered when a non-active E-DCH but active DCH primary
CPICH becomes better than an active E-DCH primary CPICH.
When event 1J is triggered, the UE reports the event-triggered list that contains good cells and
the cells to be replaced, and sequences the cells from the highest to the lowest quality according
to measurement quantity.
After receiving the measurement report, the RNC proceeds as follows:

If the current number of cells in the E-DCH active set is smaller than the value
of MaxEdchCellInActiveSet(BSC6900,BSC6910), the cell where event 1J is triggered is
reconfigured to E-DCH.

If the current number of cells in the E-DCH active set is equal to the value
of MaxEdchCellInActiveSet(BSC6900,BSC6910), the RNC searches the measurement report for
the non-serving Cell_EDCH with the lowest measured quality in the E-DCH active set. Then, the
uplink of the cell where event 1J is triggered is reconfigured from DCH to E-DCH, and the uplink of
CELL-EDCH is reconfigured from E-DCH to DCH.

Handling of HSUPA Serving Cell Uplink Out-Of-Synchronization

If experiencing uplink out-of-synchronization, the HSUPA serving cell is changed and its serving
link is removed when the link restoration timer (RlRstrTmr(BSC6900,BSC6910)) expires.

The RESERVED_SWITCH_1_BIT29 switch under RsvSwitch1(BSC6900,BSC6910) in


the SET UALGORSVPARA command controls whether a cell change to the HSUPA target cell
is allowed if the HSUPA target cell is in uplink out-of-synchronization state.

When the switch is turned on, the cell change is prohibited.

When the switch is turned off, the cell change is allowed.

Handover Between E-DCHs of 10 ms TTI and 2 ms TTI

For HSUPA, 2 ms TTI and 10 ms TTI are applicable but not all the cells support 2 ms TTI. When
both 2ms-TTI-capable and 2ms-TTI-incapable cells exist in a network, a UE may undergo
handovers between E-DCHs of 10 ms TTI and 2 ms TTI (WRFD-01061404 HSUPA 2ms/10ms
TTI Handover).
Only when all the cells in the E-DCH active set support 2 ms TTI can the services be configured
to the E-DCH with 2 ms TTI. If any cell in the E-DCH active set does not support 2 ms TTI, the
services are configured on the E-DCH with 10 ms TTI.
The detailed principles are as follows:

When the uplink service is carried on the E-DCH with 2 ms TTI, if a cell that supports only 10 ms
TTI is to be added to the E-DCH active set, the source cell undergoes a radio bearer reconfiguration
to 10 ms TTI. A soft handover to the target cell is performed.
Upon each handover, if a radio link needs to be added, removed, or replaced, the RNC judges
whether all the cells in the E-DCH active set and the UE support 2 ms TTI.

If they all support 2 ms TTI and the uplink service is currently carried on the E-DCH with 10 ms
TTI, the RNC reconfigures the service to the E-DCH with 2 ms TTI.
If the reconfiguration fails, a timer is started for periodic retries to the E-DCH with 2 ms

TTI.

If the handover is performed before the timer expires, the timer is stopped.

After the handover, the RNC decides whether to start the timer, based on the handover
result.

7.2.2 HSUPA Inter-Frequency Handover


Inter-frequency handover can be triggered on the basis of coverage, load, and hierarchical cell structure
(HCS). The introduction of HSUPA does not affect the triggering conditions and decisions of these types
of inter-frequency handover.
During the execution phase, whether to reconfigure the services from E-DCH to DCH depends on the
HSUPA capability of the target cell. After the handover, a decision must be made about whether to
reconfigure the services from DCH to E-DCH.
Table 7-1 describes the three possible scenarios for inter-frequency handover.
Table 7-1 Scenarios for inter-frequency handover

Scenario 1

Scenario 2

Scenario 3

If the current service is CS Voice over HSPA and the target cell supports both HSDPA and HSUPA, the
target cell is reconfigured as an HSPA serving cell. Otherwise, the service of CS Voice over HSPA must
first be reconfigured as CS Voice over DCH.
Whether the target RNC supports CS Voice over HSPA is determined by the
parameter CSVoiceOverHspaSuppInd(BSC6900,BSC6910).

Scenario 1: Inter-Frequency Handover from an HSUPA Cell to Another HSUPA Cell

Assume that the UE moves from HSUPA cell 1 to HSUPA cell 2 and that the two cells are interfrequency neighboring cells, as shown in Figure 7-6.
Figure 7-6 Inter-frequency handover from an HSUPA cell to another HSUPA cell

During this procedure, event 2B is triggered. The HSUPA admission request is made for the
target cell by the RNC.

If the request is accepted, the handover is performed through the physical channel
reconfiguration message.

If the request is rejected, the RB reconfiguration is implemented, and the services on the E-DCH
are reconfigured for the DCH.

Scenario 2: Inter-Frequency Handover from an HSUPA Cell to a Non-HSUPA Cell

Assume that the UE moves from HSUPA cell 1 to non-HSUPA cell 2 and that the two cells are
inter-frequency neighboring cells, as shown in Figure 7-7.
Figure 7-7 Inter-frequency handover from an HSUPA cell to a non-HSUPA cell

During this procedure, event 2B is triggered, and the target cell does not support HSUPA. The
DCH admission request is made for the target cell. If the request is accepted, the RB
reconfiguration is implemented, and the services on the E-DCH are reconfigured for the DCH.
Scenario 3: Inter-Frequency Handover from a Non-HSUPA Cell to an HSUPA Cell

Assume that the UE moves from non-HSUPA cell 1 to HSUPA cell 2 and that the two cells are
inter-frequency neighboring cells, as shown in Figure 7-8.

Figure 7-8 Inter-frequency handover from a non-HSUPA cell to an HSUPA cell

During this procedure, event 2B is triggered. The inter-frequency handover on DCH is


performed, and the HSUPA admission request is made for the target cell by the RNC.
If the request is accepted, the RB reconfiguration is implemented, and the services on the DCH
are reconfigured for the E-DCH.
7.2.3 HSUPA Inter-RAT Handover
If the current service is CS voice service and the UE is handed over from a 2G cell to a 3G cell,

If the UE supports CS Voice Over HSPA and the target 3G RAN supports CS Voice Over HSPA,
the service is configured as CS Voice over HSPA when the UE is handed over to the 3G system.

Otherwise, the service is configured as CS Voice Over DCH when the UE is handed over to the
3G system.

7.3 HSPA+ Handover


7.3.1 Overview
The basic mechanisms of handover remain unchanged after the introduction of HSPA+. New functions
are added to handle the scenario where the source cell and target cell support different HSPA+
technologies or where admission control prevents the UE from using the preferred technologies.
Whether a neighboring cell supports HSPA+ technologies can be set through the
parameter CellCapContainerFdd(BSC6900,BSC6910).
Figure 7-9 shows the procedure of HSPA+ technology configuration.

Figure 7-9 Procedure of HSPA+ technology configuration

The procedure of HSPA+ technology configuration is as follows:


1.

In the preselection phase (during handover decision)


The RNC preselects HSPA+ technologies based on the technologies provided for the UE in the
source cell and the capability of the target cell.

2.

In the fallback phase (during handover execution)


The RNC attempts to apply the preselected technologies to the UE in the target cell. If the RNC
fails to do so, it attempts to apply DCH to the UE.

3.

In the retry phase (after handover)


After the handover, the RNC attempts to apply the preselected technologies that failed to be
applied to the UE in the target cell.

7.3.2 Preselection Phase


HSPA+ technologies are preselected in the preselection phase (during handover decision).
For DC-MIMO, DC-HSUPA, DC-HSDPA, MIMO+64QAM, MIMO, 64QAM, downlink enhanced L2, and
HS-SCCH Less Operation, the preselection schemes are as follows:

If the target cell supports the same technologies as the source cell and the bearer scheme allows
the target cell to continue using them, the RNC preselects these technologies for the target cell.

Otherwise, the RNC preselects the technologies supported by the target cell and used by the UE
in the source cell.

For uplink 16QAM, uplink enhanced L2 and DTX/DRX, the preselection schemes are as follows:

During an intra-frequency soft handover, the RNC preselects HSPA+ technologies if both of the
following conditions are met:

All the cells in the active set support the technologies.

The target cell supports the technologies.


Otherwise, the RNC does not preselect them.

During an intra- or inter-frequency hard handover, the RNC preselects the technologies supported
by the target cell and used by the UE in the source cell. For example, if the UE uses MIMO and
downlink enhanced L2 in the source cell and the target cell supports only downlink enhanced L2, the
RNC preselects only downlink enhanced L2 for the UE.

7.3.3 Fallback Phase


HSPA+ technologies with lower ranking are selected in the fallback phase (during handover execution).
In this phase, the RNC performs admission control based on the preselected technologies.

If the admission is unsuccessful, the RNC selects DCH to carry services.

7.3.4 Retry Phase


In the retry phase, if both the UE and the network meet the requirements for configuring higher-ranked
technologies, the RNC attempts to apply them, which may not be pre-selected in the preselection phase
or fails to be applied in the fallback phase. For example, the RNC attempts to use DC-HSDPA instead of
SC-HSDPA.
The retry procedure is as follows:
1.
2.
3.

The RNC starts the handover protection timer


(ChannelRetryHoTimerLen(BSC6900,BSC6910)).
After the timer expires, the RNC attempts to apply higher-ranked technologies.
If the retry fails, the RNC starts the retry timer (ChannelRetryTimerLen(BSC6900,BSC6910)) for
periodic retry attempts.

The HSPA+ technologies that can be retried are specified by the


parameter RetryCapability(BSC6900,BSC6910).

7.4 Anti-Frequent Serving Cell Change


HSPA serving cell change is usually triggered by event 1D. To avoid frequent serving cell change that
may affect the system performance, a protection timerHspaTimerLen(BSC6900,BSC6910) is introduced.
This timer shall be started when the serving HS-DSCH cell changes or the E-DCH serving cell changes.
In addition, no more 1D-triggered serving cell change shall be performed until the timer expires. However,
this timer shall not restrict HSPA serving cell change to another cell in the active set if current serving cell
is to be removed from the active set. The value 0 means this timer shall not be started and serving cell
change be initiated immediately.

7.5 HSPA Retry


If a UE has a HSDPA/HSUPA suitable service, the RNC tries to reconfigure the service onto the HSDSCH/E-DCH as soon as possible.
After handover or radio bearer setup, the HSPA suitable service may be set up on the DCH or FACH in a
cell. If the cell is capable of HSPA or the cell has an HSPA-capable neighboring cell, the RNC retries to
configure the service on the HS-DSCH/E-DCH in this cell or in its neighboring cell.
To avoid frequent handovers at the boundary between an HSPA cell and an R99 cell, a protection timer
(ChannelRetryHoTimerLen(BSC6900,BSC6910)) is used. After a handover, the timer starts. After this
timer expires, the RNC retries to configure the service of the UE onto the HS-DSCH or E-DCH if either of
the following two conditions is met:

The target cell supports HSDPA or HSUPA.

The target cell does not support HSDPA or HSUPA but has a DRD neighboring cell.

If the admission fails during the reconfiguration, the timer


(ChannelRetryHoTimerLen(BSC6900,BSC6910)) is started. Periodic retries to HS-DSCH or E-DCH are
performed.

8 HCS Handover
8.1 Overview
HCS handover (WRFD-021200 HCS) is one type of inter-frequency handover and inter-RAT handover.
HCS handover is based on UE speed estimation, and is also called speed-based handover.

In a 3G network, hot spots in radio communication may appear with the increase of subscribers and
traffic. This requires more cells to increase the network capacity. More cells and smaller cell radius lead to
more frequent handovers of UEs. For a UE in fast movement, frequent handovers reduce call quality,
increase uplink interference, and increase signaling load. Here, Hierarchical Cell Structure (HCS) is a
mechanism that arranges different cells at different layers, each layer granted a priority. HCS handover
instructs UEs to stay at cells with different priorities based on speed estimation, increasing the network
capacity.
Figure 8-1 shows an HCS example with three layers.
Figure 8-1 HCS with three layers

The features of different cells are as follows:

Macro cell

Large coverage

Continuous coverage

Low requirement for capacity

Fast-moving environment

Micro cell

Densely populated areas

High requirement for capacity

Slow-moving environment

Pico cell

Indoor coverage

Outdoor blind spot coverage

Slow-moving environment

The pico cell has the highest HCS priority but the smallest coverage and the macro cell has the lowest
HCS priority but the largest coverage.
Based on speed estimation, the RNC instructs a fast-moving UE to select a cell with a lower HCS priority
to decrease the frequency of handovers, and instructs a slow-moving UE to select a cell with a higher
HCS priority to increase the network capacity.
RNC supports the HCS with eight priorities. The priority level of a cell is set by
the HCSPrio(BSC6900,BSC6910) parameter.
To allow HCS handover, the RNC must enable the function through
the HoSwitch(BSC6900,BSC6910): HO_ALGO_HCS_SPEED_EST_SWITCH parameter.

8.2 HCS Handover Procedure


HCS handover is based UE speed estimation. Figure 8-2 shows HCS handover procedure.
Figure 8-2 HCS handover procedure

In the triggering phase


The RNC receives the handover request from the HCS speed estimation function. The HCS
handover is of two types: handover from the macro cell to the micro cell and handover from the
micro cell to the macro cell. For different types of handover, the RNC acts differently.

In the measurement and decision phases

If the handover is performed from a macro cell to a micro cell, the RNC sends an interfrequency measurement control message. After the UE reports event 2C for inter-frequency
handover or 3C for inter-RAT handover, the RNC performs the handover decision.

If the handover is performed from a micro cell to a macro cell, the RNC checks whether
inter-frequency or inter-RAT blind handover neighboring cells are configured. If no, the RNC
performs the measurement procedure. If yes, the RNC performs a non-emergency blind
handover to the target cell.
In the execution phase

The RNC initiates a handover procedure.

If the handover is performed from a macro cell to a micro cell, the RNC starts the interfrequency (or inter-RAT) measurement procedure and performs the handover procedure to the
cell with the best quality after receiving event 2C or 3C from the UE.

If the handover is performed from a micro cell to a macro cell, inter-frequency or interRAT blind handover neighboring cells are configured, and the target cell allows blind handover
(configured through the parameter BlindHOFlag(BSC6900,BSC6910)), the RNC performs a
non-emergency blind handover to the target cell. If the blind handover fails, the procedure
ends.

8.3 UE Speed Estimation


This section describes high-speed estimation, low-speed estimation, and anti-ping-pong event 1D
recording.
When a UE enters the CELL_DCH state from the idle mode or CELL_PCH/URA_PCH state, the RNC
estimates the moving speed state of the UE according to the UE Mobility State Indicator information
element (IE) reported by the UE. The speed estimation principles are as follows:

If HO_HCS_SPD_INI_BSD_UE_SWITCH in the HoSwitch(BSC6900,BSC6910) parameter is


turned on, the HCS speed estimation module obtains the UE Mobility State Indicator IE from the
RRC Connection Request or Cell Update message reported by the UE. According to the UE Mobility
State Indicator IE, the HCS speed estimation module estimates the initial moving speed state of the
UE as follows:

When the UE enters the CELL_DCH state from the idle mode and the value of the UE
Mobility State Indicator IE in the RRC Connection Request message is High-mobilityDetected,
the RNC determines the UE as in the fast-moving state.

When the UE enters the CELL_DCH state from the CELL_PCH/URA_PCH state and the
value of the UE Mobility State Indicator IE in the Cell Update message is HighmobilityDetected, the RNC determines the UE as in the fast-moving state.

If neither of the preceding conditions is met, the RNC determines the UE as in the
normal-moving state.

If HO_ HCS_ SPD_INI_BSD_UE_SWITCH in the HoSwitch(BSC6900,BSC6910) parameter is


turned off, the RNC determines the UE as in the normal-moving state.
NOTE:
A UE can report the UE Mobility State Indicator IE only in the networks complying with 3GPP
Release 7 or later.
For details about speed estimation and cell reselection parameters for the UEs in idle mode or in
the CELL_PCH/URA_PCH state, see the UE Behaviors in Idle Mode Feature Parameter
Description.

After UE enters CELL_DCH state from CELL_PCH/URA_PCH or idle state, based on the number of
changes of the best cell within a specified period, the speed estimation algorithm estimates the moving
speed of the UE. Then, the RNC decides the UE speed.

The procedure for high-speed estimation is as follows:

If HoSwitch(BSC6900,BSC6910): HO_ALGO_HCS_SPEED_EST_SWITCH is set to ON and


the cell has an HCS priority that is not the lowest, the RNC initiates a high-speed estimation for the
UE after receiving an event 1D report.

If the number of changes of the best cell for the UE is higher than
the NFastSpdEst(BSC6900,BSC6910) within the TFastSpdEst(BSC6900,BSC6910), the RNC
decides that the UE is in fast movement.

The procedure for low-speed estimation is as follows:

If the HoSwitch(BSC6900,BSC6910): HO_ALGO_HCS_SPEED_EST_SWITCH is set


to ON and the cell has an HCS priority that is not the highest, the RNC starts the
timerTCycleSlow(BSC6900,BSC6910) after the RRC connection is set up.

When the timer TCycleSlow(BSC6900,BSC6910) expires, the RNC initiates a low-speed


estimation for the UE.

If the number of changes of the best cell for the UE is lower than
the NSlowSpdEst(BSC6900,BSC6910) within the TSlowSpdEst(BSC6900,BSC6910), the RNC
decides that the UE is in slow movement.

If frequent changes of the best cell occur, several events 1D for the same cell may be recorded. This may
lead to inaccurate UE speed estimation. Therefore, a mechanism is used for anti-ping-pong event 1D
recording.

During the recent period specified by TRelateLength(BSC6900,BSC6910), if multiple event 1Ds


are reported for a certain cell, only the first one is recorded.

8.4 HCS Handover Measurement


In the case of handover from a cell with a higher HCS priority to a cell with a lower HCS priority (from a
micro cell to a macro cell), the UE does not perform measurement. The RNC decides the blind handover
for the UE.
For the handover from a cell with a lower HCS priority to a cell with a higher HCS priority (from a macro
cell to a micro cell), the HCS handover uses the measurement and the UE uses event-triggered report
mode.

In inter-frequency HCS handover, event 2C takes only CPICH Ec/N0 as measurement quantity.

In inter-RAT HCS handover, event 3C takes only GSM RSSI as measurement quantity.

Triggering of Event 2C
When the signal quality of a non-used frequency is above a certain threshold, the UE reports event 2C to
the RNC.
After the conditions of event 2C are fulfilled and maintained until the
parameter TrigTime2C(BSC6900,BSC6910) is reached, the UE reports the event 2C measurement
report message.
Event 2C is triggered on the basis of the following formula:
QNoused TNoused2c + H2c/2
where

QNoused is the measured quality of the cell that uses the other frequencies.

TNoused2c is the absolute quality threshold of the cell that uses the other frequencies,
namely, InterFreqNCovHOThdEcN0(BSC6900,BSC6910).

H2c is the event 2C hysteresis value Hystfor2C(BSC6900,BSC6910).

8.5 HCS Handover Execution


HCS handover execution based on UE speed estimation falls into two categories: inter-layer handover in
fast movement and inter-layer handover in slow movement.
The inter-layer handover algorithm initiates the corresponding handover based on speed estimation:

If the UE is in fast movement, the RNC instructs the UE to select a cell with a lower HCS priority.

If the UE is in slow movement, the RNC instructs the UE to select a cell with a higher HCS
priority.

If the UE is in normal movement, no inter-layer handover occurs.

When the RNC instructs the UE to select a cell with a lower or higher HCS priority, the neighboring cells
whose frequency band is not supported by the UE are not taken into account. If there are neighboring
cells with several candidate frequencies, the RNC selects one of the frequencies randomly.

8.5.1 Inter-Layer Handover in Fast Movement


When deciding that the UE is in fast movement, the RNC instructs the UE to select a cell with a lower
HCS priority (handover from micro cell to macro cell).

If the UE is located in the overlap between the cell with an higher HCS priority and the cell with a
lower HCS priority, a blind handover is initiated.
1.

The RNC selects the neighboring cells with a lower HCS priority level to generate a cell list. The
neighboring cells whose frequency band is not supported by the UE are not taken into account. If
there are neighboring cells with several candidate frequencies, the RNC selects one of the
frequencies randomly.

2.

The RNC searches for neighboring cells for blind handover according
to BlindHOFlag(BSC6900,BSC6910)from the cell list generated in step 1.

3.

The RNC determines whether the target cell supports the current service. If the target cell does
not support the current service, the RNC does not perform the blind handover.
The target cell can be a UMTS cell or a GSM cell. The priority of an intra-RAT inter-frequency blind
handover is higher than that of an inter-RAT blind handover.

If the neighboring cell for blind handover is not configured, a measurement is initiated for cells
with a lower HCS priority.

The target cell is decided on the basis of the measurement report from the UE.

8.5.2 Inter-Layer Handover in Slow Movement


When deciding that the UE is in slow movement, the RNC instructs the UE to select a cell with a higher
HCS priority (handover from macro cell to micro cell).
The inter-layer handover algorithm initiates a measurement for cells with a higher HCS priority and then
decides the target cell based on the measurement report from the UE.

8.6 Signaling Procedure of HCS Handover

The signaling procedure for HCS handover is the same as that for inter-frequency handover and interRAT handover.

8.7 Interoperability Between HCS Handover and Other Handovers


This section describes the following aspects:

Interoperability between HCS handover and intra-frequency handover

Interoperability between HCS handover and inter-frequency handover

Interoperability between HCS handover and inter-RAT handover

8.7.1 Interoperability Between HCS Handover and Intra-Frequency Handover


If an intra-frequency handover is requested when an HCS handover measurement is initiated and an
intra-frequency cell measurement is ongoing, the HCS handover measurement is not interrupted.
After the intra-frequency handover is finished,

If the best cell remains unchanged, the HCS measurement continues.

If the best cell changes, the high-speed estimation for the UE is triggered.

8.7.2 Interoperability Between HCS Handover and Inter-Frequency Handover


An inter-frequency handover is triggered by one of the following factors:

Reporting of event 2D

QoS problem caused by the quality imbalance between uplink and downlink

Imbalance of load between inter-frequency cells

UE speed decision in HCS

Reporting of event 2D indicates that the inter-frequency handover based on coverage is triggered, which
is of high priority to be processed.

If the HCS handover algorithm is performing inter-frequency measurement when event 2D is


reported, the measurement control is modified according to the algorithm of inter-frequency
handover based on coverage.

If the RNC is performing inter-frequency measurement after event 2D is reported, HCS handover
will not be executed.

If the measurement due to other causes stops, then HCS handover measurement is restarted.
Other causes may be reception of event 2F, expiration of measurement control, or others.

When a speed-based inter-frequency handover is triggered, the RNC determines first whether the timer
specified by IFAntiPingpangTimerLength(BSC6900,BSC6910) expires.

If the timer does not expire, the RNC cancels the handover.

If the timer expires, the RNC performs the handover.

8.7.3 Interoperability Between HCS Handover and Inter-RAT Handover


It is recommended that the inter-RAT handover to 2G not be used in HCS handover.
When the UseOfHcs(BSC6900,BSC6910) parameter of a GSM cell is set to NOT_USED, this cell is not
an HCS cell. You can view the HCS attribute of a GSM cell by running the LST UEXT2GCELL command

and then check the value of the Use of HCS parameter. For details about HCS cells, see UE Behaviors in
Idle Mode Feature Parameter Description..

9 Blind Handover
9.1 Overview
There are two types of blind handover: emergent blind handover and non-emergent blind handover.

Emergent blind handover is triggered by 1F event that indicates the used frequency becomes
worse. The UE must perform emergent handover to avoid call drops.

Non-emergent blind handover may be triggered by LDR, DRD, or HCS speed estimation.

For details about LDR and DRD, see Load Control Feature Parameter Description.
For details about HCS speed estimation, see chapter 8 HCS Handover
The parameter BlindHoFlag(BSC6900,BSC6910) is configured for neighboring cells and determines
whether a blind handover to this cell is allowed.
The BlindHoFlag(BSC6900,BSC6910) parameter in the ADD UINTERFREQNCELL command and
the BlindHoFlag(BSC6900,BSC6910) parameter in the ADD U2GNCELL command specify whether a
cell is considered as a candidate cell for inter-frequency or inter-RAT blind handover, respectively.
The parameter BlindHOPrio(BSC6900,BSC6910) indicates the blind handover priority of the cell. The
value 0 represents the highest priority.
Currently, Huawei does not support inter-RNC blind handovers.

9.2 Triggering of Event 1F


After the conditions of event 1F are fulfilled and maintained until the
parameter TrigTime1F(BSC6900,BSC6910) is reached, the UE reports the event 1F measurement
report message.
Event 1F is triggered on the basis of the following formula:
10LogMOld T1f - H1f/2
where

MOld is the measurement value of the cell that becomes worse.

T1f is an absolute threshold. It is set through the


parameter IntraAblThdFor1FRSCP(BSC6900,BSC6910) or IntraAblThdFor1FecNo(BSC6900,BS
C6910).

H1f is the event 1F hysteresis value set through the parameter Hystfor1F(BSC6900,BSC6910).

9.3 Blind Handover Based on Event 1F


When the inter-frequency handover switch (HO_INTER_FREQ_HARD_HO_SWITCH) or inter-RAT
handover switch (HO_INTER_RAT_CS_OUT_SWITCH orHO_INTER_RAT_PS_OUT_SWITCH) is
turned on and there is only one cell in the active set, the RNC performs an inter-frequency or inter-RAT
blind handover after receiving event 1F.
NOTE:
Inter-frequency and inter-RAT blind handovers are also controlled by the inter-frequency and inter-RAT
handover switches in addition to the blind handover switch. When the inter-frequency or inter-RAT
handover switch is not turned on, an inter-frequency or inter-RAT blind handover cannot be performed
after event 1F is received.

1.

The RNC gets the actual best cell from event 1F. If the quality of the best cell meets the blind
handover condition, that is the quality of the best cell is larger than or equal
toBlindHORSCP1FThreshold(BSC6900,BSC6910), the RNC gets neighboring cells for blind
handover of the best cell, and filtrates the cells that belong to the frequency bands that UEs do not
support. If the quality of the best cell is lower
than BlindHORSCP1FThreshold(BSC6900,BSC6910), the UE is at the edge of the network
coverage and the blind handover is not allowed.

2.

If there are multiple neighboring cells for blind handover, the RNC chooses the cell must support
all the current services of UE. When there are multiple such cells, the RNC choose the neighboring
cell for blind handover randomly.

If any inter-frequency cell does not meet the above conditions, then the RNC chooses the inter-RAT cells
with the highest priority of blind handover. The blind handover priority of the cell is specified by the
parameter BlindHOPrio(BSC6900,BSC6910)..
If an inter-frequency blind handover based on event 1F fails, the RNC takes the same penalty measures
as those for an inter-frequency handover failure. For details, see section 5.8.1 Inter-Frequency Handover
Failure

10 Handover Protection
10.1 Anti-Ping-Pong
Inter-Frequency Anti-Ping-Pong

After an inter-frequency handover based on coverage or an inter-frequency blind handover based


on event 1F occurs, the RNC starts the anti-ping-pong algorithm to prevent frequent switching
between inter-frequency handovers triggered by different causes.
The inter-frequency anti-ping-pong algorithm is as follows:

If a coverage-based inter-frequency handover, an inter-frequency blind handover based on event


1F, or a QoS-based inter-frequency handover succeeds, the RNC starts a timer specified by
the IFHoPingPongTimer(BSC6900,BSC6910) parameter for the UE.

1.

Before the timer expires, the RNC prohibits the UE from reinitiating coverage-based interfrequency handovers, inter-frequency blind handovers based on event 1F, or QoS-based interfrequency handovers.

After the timer expires, the RNC allows the UE to reinitiate coverage-based interfrequency handovers, inter-frequency blind handovers based on event 1F, or QoS-based interfrequency handovers.

When a non-coverage-based inter-frequency handover is triggered, the RNC determines whether


the timer specified by IFAntiPingpangTimerLength(BSC6900,BSC6910)expires.

If the timer does not expire, the RNC cancels the handover.

If the timer expires, the RNC performs the handover.

Inter-RAT (2G-to-3G) Anti-Ping-Pong

For the 2G-to-3G handover, the measurement control message is delivered through a system
information broadcast of 2G when the 2G cell has a neighboring 3G cell. The dual-mode MS
performs the inter-RAT measurement in idle timeslots and reports the measurement result. Based
on the reported measurement values, the BSC decides whether to perform the handover to the 3G
network.

To avoid the ping-pong handover between 2G and 3G, the 2G-to-3G handover penalty algorithm
is used.
When the UE is handed over from 2G to 3G and if any CS domain service exists, the system
increases the hysteresis of event 3A through the
parameterInterRATPingPongHyst(BSC6900,BSC6910) to prevent the UE from the pingpong handover between 2G and 3G in the period specified by the
parameterInterRATPingPongTimer(BSC6900,BSC6910). During the penalty time, the
previous periodical report will be changed to the event 3A report. The value 0 indicates that the
system does not take measures to avoid ping-pong handover between 2G and 3G networks.
10.2 Handover Retry
10.2.1 Inter-Frequency Handover Retry
If an inter-frequency handover based on event-triggered measurement report mode fails, the RNC
initiates the inter-frequency handover attempt according to inter-frequency retry algorithm.

After the inter-frequency handover fails, the retry timer for the cell is started.
After the retry timer expires, the UE makes a handover attempt to the cell again until the number
of retry times exceeds the maximum number of retry times. If the handover succeeds or two new
event 2B reports are received, the periodical retry is stopped.

For the inter-frequency handover based on coverage or QoS, the following two parameters determine the
retry period and the maximum number of retry times:

Retry timer: PeriodFor2B(BSC6900,BSC6910)

Maximum number of retry times: AmntOfRpt2B(BSC6900,BSC6910)

For the inter-frequency handover based on speed, the following two parameters determine the retry
period and the maximum number of retry times:

Retry timer: PeriodFor2C(BSC6900,BSC6910)

Maximum number of retry times: AmntOfRpt2C(BSC6900,BSC6910)

10.2.2 Inter-RAT (3G-to-2G) Handover Retry


For an inter-RAT handover failure, if the cause of the failure is not a configuration failure and the retry
timer expires, the UE makes attempts to hand over to the cell again until the number of retry times
exceeds the maximum number of retry times.
The retry timer and maximum number of retry times for coverage-based and QoS-based inter-RAT
handover are:

Retry timer: PeriodFor3A(BSC6900,BSC6910)

Maximum number of retry times: AmntOfRpt3A(BSC6900,BSC6910)

The retry timer and maximum number of retry times for load-based and service-based inter-RAT
handover are:

Retry timer: PeriodFor3C(BSC6900,BSC6910)

Maximum number of retry times: AmntOfRpt3C(BSC6900,BSC6910)

The inter-RAT handover retry algorithm works in the following two signaling procedures:

Signaling procedure for Iu relocation

Signaling procedure for service-based handover on the Uu Interface

Signaling Procedure for Iu Relocation


1.
2.

The RELOCATION REQUIRED message is initiated on the Iu interface.


If the RNC receives the RELOCATION PREPARATION FAILURE message, the inter-RAT
handover fails.
If the cause of the failure is one of the following configuration failures, the RNC does not make a
handover retry to the cell.

Relocation Failure in Target CN/RNC or Target System, or

Relocation not supported in Target RNC or Target System, or

Relocation Target not allowed in Target RNC or Target System.


Otherwise, the related retry timer for the cell is started. After the retry timer expires, the UE
makes a handover attempt to the cell again until the number of retry times exceeds the
maximum number of retry times.

3.

If the RNC receives the RELOCATION COMMAND message, the handover on the Uu interface
continues.

4.

If the handover succeeds or the new event 3A or 3C report is received, the periodical retry is
stopped.

Signaling Procedure for Service-based Handover on the Uu Interface

For CS services or CS and PS combined services, the HANDOVER FROM UTRAN signaling
procedure on the Uu interface is performed only when the handover based on CS services is made.

For a PS service or combined PS services, the CELL CHANGE ORDER FROM UTRAN or
HANDOVER FROM UTRAN signaling procedure on the Uu interface is performed.

If the HANDOVER FROM UTRAN FAILURE or CELL CHANGE ORDER FROM UTRAN
FAILURE message is received, the handover on the Uu interface fails.

If the "Inter-RAT handover failure cause" in HANDOVER FROM UTRAN FAILURE message
is "Configuration unacceptable", or if the "Inter-RAT change failure cause" in CELL CHANGE
ORDER FROM UTRAN FAILURE message is "Configuration unacceptable", the RNC does not
make a handover retry to the cell.
Otherwise, the related retry timer for the cell is started. After the retry timer expires, the UE
makes a handover attempt to the cell again until the number of retry times exceeds the maximum
number of retry times.
If the handover succeeds or the new event 3A or 3C report is received, the periodical retry is
stopped.
10.3 Inter-RAT Multimedia Fallback
This section describes the feature Video Telephony Fallback to Speech (AMR) for Inter-RAT HO. This
feature is an enhancement to the following features:

WRFD-021200 HCS (Hierarchical Cell Structure)

WRFD-020303 Inter-RAT Handover Based on Coverage

WRFD-020305 Inter-RAT Handover Based on Service

WRFD-020306 Inter-RAT Handover Based on Load

Before the RNC performs handover for the UE that is enjoying the video phone (VP) service, the RNC
initiates multimedia fallback to change the VP service to the Adaptive Multi Rate (AMR) speech service,
that is, to perform the 3G-to-2G handover based on the CS AMR speech service.

Overview of Fallback Service

Compared with the traditional speech service of the GSM, the VP service of the UMTS can
transmit not only speech services between the calling party and the called party, but also the
images and videos captured by both parties. Since the actual implementation is limited by
terminals and networks, the VP service sometimes carries only speech and may fail to transmit
images or videos. In this scenario, the Service Change and Unrestricted Digital Information
Fallback (SCUDIF) provide the fallback mechanism that changes a video call to a common
speech call.
As specified in section 4.3 Core Network procedure in 3GPP TS 23.172 V10.0.0, the fallback
service of the VP is categorized into the following two types:

The process of changing multimedia services back to speech services during call setup. The
RNC does not take part in the process. Therefore, the detailed description of fallback process is not
given.
The process of changing multimedia services back to speech services during the call.

Triggering of Fallback Service

Currently, the network-initiated multimedia fallback is performed only for the 3G-to-2G
handover. Service changes triggered by the UEs are not supported.
Fallback is initiated when both of the following occasions are met:

The RNC decides to send an inter-RAT handover request after receiving periodical measurement
reports of event 1A, 3A, or 3C.

The service is combined with a VP, and the "Alternative RAB Parameters" in the RAB
ASSIGNMENT message is a valid AMR speech format.

Procedure of Service Change

Figure 10-1 shows the service change procedure for the 3G-to-2G handover. The network
initiates the service change, that is, the RNC initiates the change from the VP service to the
speech service during the call.

Figure 10-1 Service change procedure for the 3G-to-2G handover in the CS domain

1.

The CN sends the SRNC a RANAP RAB ASSIGNMENT REQUEST message to set up the VP
service.

2.

During 3G-to-2G handover, the SRNC sends a RANAP RAB MODIFY REQUEST message to
change the VP service to the AMR speech service. In the section 9.1.46 RAB MODIFY REQUEST
and 9.2.1.45 Requested RAB Parameter Values in 3GPP TS 25.413 V6.5.0, the information
element (IE) Alternative RAB Configuration Request is also added to the RAB MODIFY REQUEST
message, which enables the RNC to request the CN to change the VP service to the AMR speech
service.

3.

The MSC initiates the Bearer Capability (BC) negotiation with the UE.

4.

After the negotiation, the RNC is requested to perform service change.

When the multimedia fallback ends, the RNC decides whether to perform the 3G-to-2G
handover according to the current measurements reported by the UE.
The CN initiates the RAB reconfiguration to request both parties to perform the multimedia
fallback. The single VP service falls back to the single AMR speech service. The multi-RAB
service combined with VP falls back to the multi-RAB service combined with AMR. If the
multimedia fallback succeeds, that is, the video phone in the service falls back to speech
successfully, the inter-RAT handover is initiated. Otherwise, the inter-RAT handover fails.
10.4 Transferring Event Report to Periodical Report

After a UE reports event 1A, 1C or, 1J to the RNC, the RNC may miss the measurement reports. If the
reported cell does not join active set in a specified period of time, the UE starts to report the event
periodically to avoid missing of measurement reports.
The following parameters specify the reporting period of events.

ReportIntervalfor1A(BSC6900,BSC6910)

ReportIntervalfor1C(BSC6900,BSC6910)

ReportIntervalfor1J(BSC6900,BSC6910)

The following parameters specify the number of reporting times of events for periodical reporting:

PeriodMRReportNumfor1A(BSC6900,BSC6910)

PeriodMRReportNumfor1C(BSC6900,BSC6910)

PeriodMRReportNumfor1J(BSC6900,BSC6910)
When the actual reporting times exceed the set value, the periodical reporting ends.

11 Neighboring Cell Combination


11.1 Overview
After the active set is updated, the RNC updates the neighboring cell list by using the neighboring cell
combination algorithm according to the status of the active set. This list includes the new intra-frequency,
inter-frequency, and inter-RAT neighboring cells. The combination methods of intra-frequency handover,
inter-frequency handover, and inter-RAT handover are the same.
If the radio link of the drift RNC (DRNC) is added to the active set, the source RNC (SRNC) buffers the
intra-frequency, inter-frequency, and inter-RAT neighboring cell lists of the DRNC until the radio link of the
DRNC is released.
The neighboring cell combination result is contained in the MEASUREMENT CONTROL message and
sent to the UE, which instructs the UE to perform intra-frequency, inter-frequency, and inter-RAT
measurement and handover procedures.
The maximum number of neighboring cells of a cell that can be configured is as follows:

The maximum number of intra-frequency neighboring cells is 64, which includes the cell itself.
NOTE:

When the number of configured intra-frequency neighboring cells exceeds 32,


the HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH andHO_INTRA_FREQ_DETSET_RPRT_S
WITCH switches of the HoSwitch(BSC6900,BSC6910) parameter must be turned on. Otherwise, the
RNC will not select these extra intra-frequency neighboring cells as candidate target cells.

The maximum number of inter-frequency neighboring cells of single carrier is 32.

The maximum number of inter-frequency neighboring cells of multi-carrier is 64.

The maximum number of inter-RAT neighboring cells of multi-carrier is 64

11.2 Neighboring Cell Combination Switches


The neighboring cell combination result is contained in the MEASUREMENT CONTROL message and
sent to the UE, which instructs the UE to perform intra-frequency, inter-frequency, and inter-RAT
measurement and handover procedures.

The maximum number of neighboring cells of a cell that can be configured is as follows:

The maximum number of intra-frequency neighboring cells is 64, which includes the cell itself.
NOTE:

When the number of configured intra-frequency neighboring cells exceeds 32,


the HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH andHO_INTRA_FREQ_DETSET_RPRT_S
WITCH switches of the HoSwitch(BSC6900,BSC6910) parameter must be turned on. Otherwise, the
RNC will not select these extra intra-frequency neighboring cells as candidate target cells.

The maximum number of inter-frequency neighboring cells of single carrier is 32.

The maximum number of inter-frequency neighboring cells of multi-carrier is 64.

The maximum number of inter-RAT neighboring cells of multi-carrier is 64

11.3 Procedure of the Neighboring Cell Combination


After obtaining the intra-frequency, inter-frequency, and inter-RAT neighboring cells of each cell in the
active set, the RNC calculates the combined neighboring cell set, which is referred as S all, by using the
following method.
These neighboring cells and active cells are added to S all in the following order until the number reaches
the maximum number of neighboring cells:
1.

The best cell in the active is added to Sall.


The best cell is reported on event 1D.

2.

Other cells in the active set are added to Sall in descending order by CPICH Ec/N0.

3.

The neighboring cells of the best cell in the active set are added to S all.
NprioFlag(BSC6900,BSC6910) (the flag of the priority) and Nprio(BSC6900,BSC6910) (the
priority of the neighboring cell), which are set for each neighboring cell, are used to change the
order of adding the neighboring cells to Sall. NprioFlag and Nprio of intra-frequency, interfrequency, and inter-RAT neighboring cells are set in the ADD/MOD
UINTERFREQNCELL, ADD/MOD UINTRAFREQNCELL, and ADD/MOD U2GNCELL commands,
respectively.

4.

When NprioFlag(BSC6900,BSC6910) is switched to


FALSE, Nprio(BSC6900,BSC6910) is cleared.

When NprioFlag(BSC6900,BSC6910) is switched to


TRUE, Nprio(BSC6900,BSC6910) is set simultaneously.

The neighboring cells of other cells in the active set are added to S all in descending order by
CPICH Ec/N0 values of these cells in the active set. The number to be repeatedly added of each
neighboring cell is recorded.

The neighboring cells of the same cell in the active set are added according
to Nprio(BSC6900,BSC6910).
If the number of the cells in Sall is more than maximum number of neighboring cells, delete the
neighboring cells whose repeated number in Sall is less. The best cell and its neighboring cells will not be
deleted.

12 Missing Neighboring Cell Detection


12.1 Overview

An RNC may fail to configure some neighboring cells in a cell's neighboring cell list. These neighboring
cells include intra-frequency, inter-frequency, and inter-RAT neighboring cells. The causes of the failures
are classified into the following:

Predictable causes. for example, a cell is added or a cell's frequency or scrambling code
changes.
Unpredictable causes, for example, a building is demolished, causing changes in cell coverage.

If the neighboring cell list is not updated in time to adapt to these changes, some neighboring cells may
be missing.
Missing neighboring cells may result in call drops or deteriorated signal quality because UEs cannot be
handed over to appropriate neighboring cells in time. Missing neighboring cell detection consists of the
following:

Missing intra-frequency neighboring cell detection

Missing inter-frequency neighboring cell detection

Missing inter-RAT neighboring cell detection

12.2 Missing Intra-Frequency Neighboring Cell Detection


A detected set cell is not in a UE's neighboring cell list, which is contained in the measurement control
message. However, according to section 10.3.7.39 "Intra-frequency measurement reporting criteria" in
3GPP TS 25.331 V10.0.0, like a monitored set cell, a detected set cell can also be contained in an intrafrequency measurement report triggered by a 1X (1A, 1C, and 1D) event. Upon receiving the information
about the detected set cell from the UE, the RNC regards the detected set cell as a missing intrafrequency neighboring cell because the cell is not contained in the neighboring cell list. Then, the RNC
reports the detected set cell to the Nastar or LMT.
Missing intra-frequency neighboring cell detection is controlled by
the IntraFreqNCellDetectSwitch(BSC6900,BSC6910) parameter in the RNC MML command SET
UNCELLDETECTSWITCH.

When this switch is turned on, missing intra-frequency neighboring cell detection is enabled. A UE
can report both detected set cells and monitored set cells to the RNC, which then reports the
missing intra-frequency neighboring cells to the Nastar or LMT.
When this switch is turned off, missing intra-frequency neighboring cell detection is disabled.

12.3 Missing Inter-Frequency or Inter-RAT Neighboring Cell Detection


A UE only measures cells in the inter-frequency or inter-RAT neighboring cell list contained in the
measurement control message from the RNC to the UE. Therefore, you can configure as many interfrequency or inter-RAT neighboring cells as possible in the neighboring cell list. Upon receiving an interfrequency or inter-RAT neighboring cell measurement report from the UE, the RNC compares the
reported cell with the neighboring cell list and determines whether the reported cell is a missing
neighboring cell.
Run the RNC MML command ADD UAUTOINTERNCELLGROUP or ADD
UAUTOGSMNCELLGROUP to configure cells that may be missing inter-frequency or inter-RAT
neighboring cells.
The RNC then adds these cells to the inter-frequency or inter-RAT neighboring cell list of the UEs that
require inter-frequency or inter-RAT measurement. Then, the UEs perform inter-frequency or inter-RAT
measurement. When receiving a measurement report from a UE, the RNC determines whether the cell in
the measurement report is a missing neighboring cell.

Missing inter-frequency neighboring cell detection is controlled by


the InterFreqNCellDetectSwitch(BSC6900,BSC6910) parameter in the RNC MML command SET
UNCELLDETECTSWITCH.

When this switch is turned on, missing inter-frequency neighboring cell detection is
enabled. The RNC reports the missing inter-frequency neighboring cells to the Nastar or LMT.

When this switch is turned off, missing inter-frequency neighboring cell detection is
disabled.

Missing inter-RAT neighboring cell detection is controlled by


the InterFreqNCellDetectSwitch(BSC6900,BSC6910) parameter in the RNC MML command SET
UNCELLDETECTSWITCH.

When this switch is turned on, missing inter-RAT neighboring cell detection is enabled.
The RNC reports the missing inter-RAT neighboring cells to the Nastar or LMT.

When this switch is turned off, missing inter-RAT neighboring cell detection is disabled.

13 Compressed Mode
13.1 Overview
Compressed mode control is a mechanism whereby certain idle periods are created in radio frames
during which the UE can perform measurements on other frequencies. The UE must use the compressed
mode if the UE needs to measure the pilot signal strength of an inter-frequency cell or inter-RAT cell and
has a single-frequency receiver only.
Figure 13-1 Compressed mode

13.2 Compressed Mode Switches


The parameter DlSFLimitCMInd(BSC6900,BSC6910) decides whether to start the DL compressed mode
according to the parameter LimitCMDlSFThd(BSC6900,BSC6910).

If DlSFLimitCMInd(BSC6900,BSC6910)= True,

When the downlink spreading factor is smaller than or equal to the


parameter LimitCMDlSFThd(BSC6900,BSC6910), the compressed mode is disabled.

When the downlink spreading factor is greater than the


parameter LimitCMDlSFThd(BSC6900,BSC6910), the compressed mode is enabled.

If DlSFLimitCMInd(BSC6900,BSC6910)= False, the compressed mode is not limited by the


downlink spreading factor.

The uplink 384 kbit/s uses SF4. The method of SF/2 is not allowed for the services of SF4.

CMCF_UL_PRECFG_TOLERANCE_SWITCH under CmcfSwitch(BSC6900,BSC6910) determines


whether to set up the uplink RB of SF4 during the preparation for SF/2 compressed mode.

If CMCF_UL_PRECFG_TOLERANCE_SWITCH is set to ON, the RB of SF4 can be set up


during the preparation for SF/2 compressed mode. The inter-frequency or inter-RAT handover
measurement, however, cannot be triggered, because SF4 cannot be compressed to SF2.

If CMCF_UL_PRECFG_TOLERANCE_SWITCH is set to OFF, the RB of SF4 cannot be set up


during the preparation for SF/2 compressed mode. The system can trigger the SF/2 compressed
mode measurement.

CMCF_WITHOUT_UE_CAP_REPORT_SWITCH under CmcfSwitch(BSC6900,BSC6910) determines


whether to use the frequencies beyond the range of UE reports on the compressed mode measurement.
To initiate the high layer scheduling, set the following two switches:

If the algorithm switch CMCF_DL_HLS_SWITCH in the SET UCORRMALGOSWITCH command


is set to ON, the DL high-layer scheduling for the compressed mode is allowed.

If the algorithm switch CMCF_UL_HLS_SWITCH in the SET UCORRMALGOSWITCH command


is set to ON, the UL high-layer scheduling for the compressed mode is allowed.

13.3 Compression Methods


There are two methods to implement the compressed mode as follows:
Table 13-1 Methods for implementing the compressed mode

SF/2

High layer scheduling

The RNC automatically determines the type of compressed mode on the basis of the spreading factor
used in the uplink or the downlink.

When the downlink spreading factor is greater than or equal to the


parameter DlSFTurnPoint(BSC6900,BSC6910), the SF/2 approach is preferred. Otherwise, the
high layer scheduling is used.

When the uplink spreading factor is greater than or equal to the


parameter UlSFTurnPoint(BSC6900,BSC6910), the SF/2 approach is preferred. Otherwise, the
high layer scheduling is used.

13.4 Compression Types


The compression types are as follows:

Inter-frequency measurement

Inter-RAT measurement

Coexistence of inter-frequency and inter-RAT measurement

The parameter InterFreqRATSwitch(BSC6900,BSC6910) determines the compression types allowed by


the RNC

If the parameter is set to INTERFREQ, the RNC allows the UE to perform only inter-frequency
measurement

If the parameter is set to INTERRAT, the RNC allows the UE to perform only Inter-RAT
measurement.

If the parameter is set to SIMINTERFREQRAT, the RNC allows the UE to perform both interfrequency and inter-RAT measurement.

During the concurrent inter-frequency and inter-RAT measurement, the


parameter CoexistMeasThdChoice(BSC6900,BSC6910) decides the event 2D threshold:

When the parameter is set to COEXIST_MEAS_THD_CHOICE_INTERFREQ, the inter-frequency


measurement threshold for event 2D is used.

When the parameter is set to COEXIST_MEAS_THD_CHOICE_INTERRAT, the inter-RAT


measurement threshold for event 2D is used.

13.5 Measurement Timer Length


When the UE takes a long time to perform the inter-frequency measurement in compressed mode, the
radio network will be affected. To avoid the influence, the RNC stops the inter-frequency measurement
and disables the compressed mode if no inter-frequency handover occurs upon expiry of the interfrequency measurement timer.

The timer is specified by InterFreqMeasTime(BSC6900,BSC6910) in inter-frequency handover


based on coverage.

The timer is specified by InterFreqMeasTime(BSC6900,BSC6910) in inter-frequency handover


based on load or HCS.

The timer is specified by InterRATMeasTime(BSC6900,BSC6910) in inter-RAT handover based


on coverage.

The timer is specified by InterRATMeasTime(BSC6900,BSC6910) in inter-RAT handover based


on load or service.

The timer is specified


by DLQosMcTimerLen(BSC6900,BSC6910) or ULQosMcTimerLen(BSC6900,BSC6910) in inter-RAT
handover based on downlink or uplink QoS respectively.

13.6 Check of Compressed Mode Parameter Settings During Inter-RNC Handover


If the peer RNC is non-Huawei equipment during an inter-RNC handover, the NodeB checks static
compressed mode parameter settings to avoid handover failures due to inconsistent compressed mode
parameter settings.
If the DRNC_NOTICE_NODEB_SRNC_VEST_SWITCH check box under
the OPTIMIZATIONSWITCH4(BSC6900,BSC6910) parameter in the SET URRCTRLSWITCH command
is cleared (value: 0), the NodeB checks static compressed mode parameter settings after the compressed
mode sequence is deactivated.
If the DRNC_NOTICE_NODEB_SRNC_VEST_SWITCH check box under
the OPTIMIZATIONSWITCH4(BSC6900,BSC6910) parameter in the SET URRCTRLSWITCH command
is selected (value: 1), the NodeB determines whether the peer RNC is Huawei equipment according to
the Iub private message sent by the RNC.

If the peer RNC is non-Huawei equipment, the NodeB checks static compressed mode parameter
settings when the compressed mode is being activated. An RNC is non-Huawei equipment if
the NRNC_COMPATIBLE_SWITCH check box under
the ProcessSwitch(BSC6900,BSC6910) parameter in the MOD UNRNC command is selected
(value: 1).

If the peer RNC is Huawei equipment, the NodeB checks static compressed mode parameter
settings after the compressed mode sequence is deactivated. An RNC is Huawei equipment if
the NRNC_COMPATIBLE_SWITCH check box under
the ProcessSwitch(BSC6900,BSC6910) parameter in the MOD UNRNC command is cleared
(value: 0).

13.7 Compatibility Switch for Dual-frequency Receiver


If the UE has a dual-frequency receiver, it can perform inter-frequency or inter-RAT measurement without
starting the compressed mode if all of the following conditions are met:

The CMP_UU_ADJACENT_FREQ_CM_SWITCH is on.


The value of the IE "Adjacent frequency measurements without compressed mode" reported by
the UE is TRUE.

For a UE that supports DC-HSDPA/DC-HSUPA:

If the UE has a DC-HSDPA/DC-HSUPA service, all the cells involved in inter-frequency


measurement are at the same frequency as the secondary carrier.

If the UE does not have a DC-HSDPA/DC-HSUPA service, all the cells involved in interfrequency measurement are at the same frequency, with a 5 MHz spacing from the current
cell, but within the same band as the current cell.
If a UE that supports DC-HSDPA/DC-HSUPA does not meet the preceding conditions, it needs
to perform inter-frequency or inter-RAT measurement in compressed mode. In this case, the
same sequence and type of compressed mode are required by the primary and secondary
carriers.

Each physical frame can provide three to seven timeslots for the inter-frequency or inter-RAT cell
measurement.

13.8 Compatibility Switches for HSPA


There are some UEs that do not support the compressed mode when an HSPA+ or HSDPA or HSUPA
service is active. For compatibility reasons with these UE, compatibility switch parameters have been
introduced.

HSDPA Compatibility
The parameter HsdpaCMPermissionInd(BSC6900,BSC6910) is used to enable or disable compressed
mode for HSDPA users.

If this parameter value is TRUE, compressed mode is permitted on HSDPA and HSDPA can be
activated with compressed mode activated.

If this parameter value is FALSE, H2D is required before compressed mode is activated for
HSDPA services. HSDPA UEs perform neighboring cell measurement in compressed mode. In
addition, HSDPA services cannot be established when compressed mode is activated.

HSUPA Compatibility

The parameter HsupaCMPermissionInd(BSC6900,BSC6910) decides whether the compressed mode


can be used on HSUPA.

If the parameter is set to Permit, the UE in E-DCH state performs measurement.

If the parameter is set to Limited, the reconfiguration from E-DCH to DCH is required before
compressed mode is activated. HSUPA UEs perform neighboring cell measurement in compressed
mode. In addition, HSUPA services cannot be established when compressed mode is activated.

If the parameter is set to BasedOnUECap, the RNC determines whether to perform E2D
procedure before compressed mode activated based on the UE capability.

HSPA+ Compatibility
The parameter EHSPACMPermissionInd(BSC6900,BSC6910) indicates whether the compressed mode
can be activated when an HSPA+ service is in progress and whether an HSPA+ service can be set up
when the compressed mode is active.

When the EHSPACMPermissionInd(BSC6900,BSC6910)value is FALSE, the RNC starts an RB


RECONFIGURATION procedure to degrade the HSPA+ services to DCH services, and then
requests the UE to start the compressed mode. After the hard handover is completed, the RNC
starts an RB RECONFIGURATION procedure to promote the DCH services to HSPA+ services.
That is, all HSPA+ UEs (whether support compressed mode or not) are degraded to DCH before the
compressed mode procedure.

When the EHSPACMPermissionInd(BSC6900,BSC6910)value is TRUE, the RNC does not


trigger the RB RECONFIGURATION procedure before requesting the UE to start the compressed
mode. Not affected UEs are capable to start the measurements during the HSPA+ services and can
perform the hard handover without service degrading. On the contrary, UEs that do not support the
compressed mode during HSPA+ services are not capable to complete the hard handover
procedure successfully.

DC-HSDPA Compatibility
The McHsdpaLteCMPermissionInd(BSC6900,BSC6910) parameter indicates whether the compressed
mode can be activated when a DC-HSDPA service is in progress and whether a DC-HSDPA service can
be set up when the compressed mode is active.

If the McHsdpaLteCMPermissionInd(BSC6900,BSC6910) parameter is set to TRUE, the


compressed mode can be activated when a DC-HSDPA service is in progress, and a DC-HSDPA
service can be set up when the compressed mode is active.

If the McHsdpaLteCMPermissionInd(BSC6900,BSC6910) parameter is set to FALSE, DCHSDPA to HSDPA channel switchovers are required before the compressed mode is activated for
DC-HSDPA services. DC-HSDPA UEs perform neighboring cell measurement in compressed mode.
In addition, DC-HSDPA services cannot be set up when the compressed mode is active.

If HSPA+, HSDPA, or HSUPA UEs perform H2D (HS-DSCH to DCH) or E2D (E-DCH to DCH) channel
switchovers before starting the compressed mode, or DC-HSDPA UEs perform DC-HSDPA to HSDPA
channel switchovers before starting the compressed mode, these UEs can trigger periodic retries to
return to the state after channel switchovers are complete.
Periodic DRDs in compressed mode for increasing the rate are controlled
by PS_CMACTIVE_PROCESS_OPT_SWITCH under the PsSwitch(BSC6900,BSC6910) parameter in
the SET UCORRMALGOSWITCH command as follows:

When PS_CMACTIVE_PROCESS_OPT_SWITCH is selected, UEs performing PS services in


compressed mode are prohibited from performing periodic DRDs to increase their rates in the interfrequency co-coverage cell.

When PS_CMACTIVE_PROCESS_OPT_SWITCH is deselected, UEs performing PS services in


compressed mode are allowed to perform periodic DRDs to increase their rates in the interfrequency co-coverage cell.

14 Related Features
14.1 WRFD-01061006 HSDPA Mobility Management
Prerequisite Features

The intra-frequency handover function in this feature requires at least one of the following
features:

WRFD-020201 Intra NodeB Softer Handover

WRFD-020202 Intra RNC Soft Handover

WRFD-020203 Inter RNC Soft Handover

The inter-frequency handover function in this feature requires the WRFD-020302 Inter Frequency
Hard Handover Based on Coverage feature.

The inter-RAT handover function in this feature requires the WRFD-020303 Inter-RAT Handover
Based on Coverage feature.

Mutually Exclusive Features


None

Impacted Features
If TAC_FUNC is set to Special_User_Enhance and SpecUserFunctionSwitch4 is set
to SPECUSER_NO_HSUPACM_SWITCH, the corresponding UEs in the UE blacklist cannot process
HSUPA services in compressed mode.
If TAC_FUNC is set to Special_User_Enhance and SpecUserFunctionSwitch4 is set
to SPECUSER_NO_EHSPACM_SWITCH, the corresponding UEs in the UE blacklist cannot process
HSPA+ services in compressed mode.

14.2 WRFD-01061204 HSUPA Mobility Management


Prerequisite Features

The intra-frequency handover function in this feature requires at least one of the following
features:

WRFD-020201 Intra NodeB Softer Handover

WRFD-020202 Intra RNC Soft Handover

WRFD-020203 Inter RNC Soft Handover

The inter-frequency handover function in this feature requires the WRFD-020302 Inter Frequency
Hard Handover Based on Coverage feature.

The inter-RAT handover function in this feature requires the WRFD-020303 Inter-RAT Handover
Based on Coverage feature.

Mutually Exclusive Features

None

Impacted Features
If TAC_FUNC is set to Special_User_Enhance and SpecUserFunctionSwitch4 is set
to SPECUSER_NO_HSDPACM_SWITCH, the corresponding UEs in the UE blacklist cannot process
HSDPA services in compressed mode.
If TAC_FUNC is set to Special_User_Enhance and SpecUserFunctionSwitch4 is set
to SPECUSER_NO_EHSPACM_SWITCH, the corresponding UEs in the UE blacklist cannot process
HSPA+ services in compressed mode.

14.3 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS


Prerequisite Features
WRFD-020302 Inter Frequency Hard Handover Based on Coverage

Mutually Exclusive Features


None

Impacted Features
None

14.4 WRFD-020309 Inter-RAT Handover Based on DL QoS


Prerequisite Features
WRFD-020302 Inter Frequency Hard Handover Based on Coverage

Mutually Exclusive Features


None

Impacted Features
None

15 Network Impact
15.1 WRFD-020302 Inter Frequency Hard Handover Based on Coverage
15.1.1 System Capacity
No impact.

15.1.2 Network Performance


The Inter Frequency Hard Handover Based on Coverage feature ensures the service continuity of moving
UEs and reduces the number of call drops at the coverage edge.

15.2 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS


15.2.1 System Capacity

No impact.

15.2.2 Network Performance


The Inter Frequency Hard Handover Based on DL QoS feature reduces the number of call drops caused
by reduced downlink quality and ensures the QoS for users.

15.3 Inter Frequency Hard Handover Based on UL QoS


15.3.1 System Capacity
No impact.

15.3.2 Network Performance


The Inter Frequency Hard Handover Based on UL QoS feature reduces the number of call drops caused
by reduced downlink quality and ensures the QoS for users.

15.4 WRFD-020309 Inter-RAT Handover Based on DL QoS


15.4.1 System Capacity
No impact.

15.4.2 Network Performance


The Inter Frequency Hard Handover Based on DL QoS feature reduces the number of call drops caused
by reduced downlink quality and ensures the QoS for users.

15.5 Inter-RAT Handover Based on UL QoS


15.5.1 System Capacity
No impact.

15.5.2 Network Performance


The Inter Frequency Hard Handover Based on UL QoS feature reduces the number of call drops caused
by reduced downlink quality and ensures the QoS for users.

15.6 WRFD-01061006 HSDPA Mobility Management


System Capacity
No impact.

Network Performance
The HSDPA Mobility Management feature implements all types of handovers between adjacent cells. This
provides continuous coverage and better service quality for HSDPA UEs.
RAN16.0 introduces the fast HSDPA serving cell change function, which has the following impacts on
network performance:

The delay of HSDPA serving cell change is shortened by about 400 ms. (The delay of HSDPA
serving cell change is the interval between the time when the RNC sends the PH CH RECFG
message and the time when the RNC receives the PH CH RECFG CMP message.)
The HSDPA throughput is increased by 10% to 15%.

The success rate of HSDPA serving cell changes is increased by 5% to 10%.

16 Engineering Guidelines
16.1 WRFD-020201 Intra Node B Softer Handover
This section describes how to activate, verify, and deactivate the basic feature WRFD-020201 Intra
NodeB Softer Handover.

16.1.1 Requirements

Dependencies on Hardware
Not supported by Micro base stations.

Dependencies on Other Features


This feature does not depend on other features.

License
This feature is not under license control.

16.1.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step,
selectHO_INTRA_FREQ_SOFT_HO_SWITCH under HandOver Switch to enable soft handover.

2.

Run the RNC MML command SET UHOCOMM (CME single configuration: UMTS Radio Global
Configuration Express > HandOver Parameter Configuration > RNC Oriented Handover Algorithm
Common Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
set Softer handover combination indicator switch to MAY or MUST.

3.

Run the RNC MML command ADD UINTRAFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Intra-frequency Neighboring Cell; CME batch
modification center: not supported) to add an intra-frequency neighboring cell.

4.

Run the RNC MML command SET UINTRAFREQHO (CME single configuration: UMTS Radio
Global Configuration Express > HandOver Parameter Configuration > RNC Oriented Intrafrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) to set the parameter related to handover.

16.1.3 MML Command Examples


//Activating Intra NodeB Softer Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
SET UHOCOMM: DivCtrlField=MAY;
ADD UINTRAFREQNCELL: RNCId=202, CellId=2381, NCellRncId=203, NCellId=3291, SIB11Ind=TRUE,
SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
SET UINTRAFREQHO: FilterCoef=D3, IntraFreqMeasQuantity=CPICH_EC/N0,
PeriodMRReportNumfor1C=D16, ReportIntervalfor1C=D4000;

16.1.4 Activation Observation

1.

On the RNC LMT, click Trace > UMTS Services, and then double-click Uu Interface Trace.
The Uu Interface Trace dialog box is displayed.

2.

Set parameters in the areas Cell Config, Uu Message Type, and Save File. Then, click Submit.

3.

The UE is in idle mode and camping on CELL1.

4.

The UE initiates PS services. The services are successfully set up.

5.

6.

The UE moves from CELL1 to CELL2. Through Trace Data, it can be observed that the RNC
sent the RRC_ACTIVE_SET_UPDATE message to the UE and the UE returned the
RRC_ACTIVE_SET_UPDATE_CMP message to the RNC.
The data transmission remains normal while UE is moving to CELL2.

16.1.5 Deactivation
Run the RNC MML command SET UHOCOMM (CME single configuration: UMTS Radio Global
Configuration Express > HandOver Parameter Configuration > RNC Oriented Handover Algorithm
Common Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
set Softer handover combination indicator switch to MUST_NOT.

16.1.6 MML Command Examples


//Deactivating Intra NodeB Softer Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-0;

16.2 WRFD-020202 Intra RNC Soft Handover


This section describes how to activate, verify, and deactivate the basic feature WRFD-020202 Intra RNC
Soft Handover.

16.2.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
This feature is not under license control.

16.2.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to enable soft handover.

2.

Run the RNC MML command ADD UINTRAFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Intra-frequency Neighboring Cell; CME batch
modification center: not supported) to add an intra-frequency neighboring cell.

3.

Run the RNC MML command SET UINTRAFREQHO (CME single configuration: UMTS Radio
Global Configuration Express > HandOver Parameter Configuration > RNC Oriented Intrafrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) to set the parameter related to handover.

16.2.3 MML Command Examples


//Activating Intra RNC Soft Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
ADD UINTRAFREQNCELL: RNCId=202, CellId=2381, NCellRncId=203, NCellId=3291,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
SET UINTRAFREQHO: FilterCoef=D3, IntraFreqMeasQuantity=CPICH_EC/N0,
PeriodMRReportNumfor1C=D16, ReportIntervalfor1C=D4000;

16.2.4 Activation Observation


1.

On the RNC LMT, click Trace > UMTS Services, and then double-click Uu Interface Trace.
The Uu Interface Trace dialog box is displayed.

2.

Set parameters in the areas Cell Config, Uu Message Type, and Save File. Then, click Submit.

3.

Both UE1 and UE2 are in idle mode and camp on the CELL1.

4.

UE1 calls UE2, and the conversation is clear.

5.

UE1 moves from CELL1 to CELL2, through the Trace Data, it can be observed that RNC1 sends
the RRC_ACTIVE_SET_UPDATE message to UE1, and UE1 sends the
RRC_ACTIVE_SET_UPDATE_CMP message to RNC1.

16.2.5 Deactivation
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS Radio
Global Configuration Express > Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: Modifying RNC Parameters in Batches) to set Softer
handover combination indicator to disable the soft handover.

16.2.6 MML Command Examples


//Deactivating Intra RNC Soft Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-0;

16.3 WRFD-020203 Inter RNC Soft Handover


This section describes how to activate, verify, and deactivate the optional feature WRFD-020203 Inter
RNC Soft Handover.

16.3.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
This feature is not under license control.

Other Requirements
The Iur interface is configured between adjacent RNCs.

16.3.2 Activation

1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to enable soft handover.

2.

Run the RNC MML command ADD UNRNC (CME single configuration: IUR Configuration
Express > Neighbouring RNC > Neighboring RNC; CME batch modification center: not supported)
or MOD UNRNC (CME single configuration: IUR Configuration Express > Neighbouring RNC >
Neighboring RNC; CME batch modification center: not supported) to enable cross-Iur soft
handover.

3.

Run the RNC MML command ADD UEXT3GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
3G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to add a neighboring RNC cell.

4.

Run the RNC MML command ADD UINTRAFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Intra-frequency Neighboring Cell; CME batch
modification center: not supported) to add an intra-frequency neighboring cell.

5.

Run the RNC MML command SET UINTRAFREQHO (CME single configuration: UMTS Radio
Global Configuration Express > HandOver Parameter Configuration > RNC Oriented Intrafrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) to set the parameter related to handover.

16.3.3 MML Command Examples


//Activating Inter RNC Soft Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
MOD UNRNC: NRncId=1, SHOTRIG=CS_SHO_SWITCH-1&HSPA_SHO_SWITCH1&NON_HSPA_SHO_SWITCH-1;
ADD UEXT3GCELL: NRncId=1, CellId=2381, CellHostType=SINGLE_HOST,
CellName="2222", CnOpGrpIndex=0, PScrambCode=256, BandInd=Band1,
UARFCNUplinkInd=TRUE, UARFCNUplink=9750, UARFCNDownlink=10700,
TxDiversityInd=FALSE, LAC=2506, CfgRacInd=NOT_REQUIRE, QqualminInd=FALSE,
QrxlevminInd=FALSE, MaxAllowedUlTxPowerInd=FALSE, UseOfHcs=NOT_USED,
CellCapContainerFdd=EDCH_SUPPORT-1, EFachSupInd=FALSE;
ADD UINTRAFREQNCELL: RNCId=1, CellId=221, NCellRncId=2, NCellId=222,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;

16.3.4 Activation Observation


1.

On the RNC LMT, click Trace > UMTS Services, and then double-click Uu Interface Trace.
The Uu Interface Trace dialog box is displayed.

2.

Set parameters in the areas Cell Config, Uu Message Type, and Save File. Then, click Submit.

3.

Both UE1 and UE2 are in idle mode and camp on the CELL1.

4.

UE1 calls UE2, and the conversation is clear.

5.

UE1 moves from CELL1 to CELL2, through the Trace Data, it can be observed that RNC1 sends
the RRC_ACTIVE_SET_UPDATE message to UE1, and UE1 sends the
RRC_ACTIVE_SET_UPDATE_CMP message to RNC1.

16.3.5 Deactivation
Run the RNC MML command MOD UNRNC (CME single configuration: IUR Configuration Express >
Neighbouring RNC > Neighboring RNC; CME batch modification center: not supported) to disable the
cross-Iur soft handover.

16.3.6 MML Command Examples


//Deactivating Inter RNC Soft Handover
MOD UNRNC: NRncId=1, SHOTRIG=CS_SHO_SWITCH-0&HSPA_SHO_SWITCH0&NON_HSPA_SHO_SWITCH-0;

16.4 WRFD-020301 Intra Frequency Hard Handover


This section describes how to activate, verify, and deactivate the optional feature WRFD-020301 Intra
Frequency Hard Handover.

16.4.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
This feature is not under license control.

16.4.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to select HO_INTRA_FREQ_HARD_HO_SWITCH from the HandOver
switch list.

2.

Run the RNC MML command ADD UINTRAFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Intra-frequency Neighboring Cell; CME batch
modification center: not supported) to add an intra-frequency or inter-RNC neighboring cell.

3.

If cross-Iur hard handover is required, add the neighboring RNC and neighboring RNC cell. Run
the RNC MML command ADD UNRNC (CME single configuration: IUR Configuration Express >
Neighbouring RNC > Neighboring RNC; CME batch modification center: not supported) to add a
neighboring RNC. Run the RNC MML commandADD UEXT3GCELL (CME single configuration:
Object Group > UMTS Service Configuration and Maintenance Management > External Cell
Configuration > RNC 3G External Cell; CME batch modification center: Modifying RNC External
Cell Parameters in Batches) to add a neighboring RNC cell. Run the RNC MML command ADD
UINTRAFREQNCELL (CME single configuration: UMTS Cell Configuration Express > Neighboring
Cell > Intra-frequency Neighboring Cell; CME batch modification center: not supported) to set the
neighboring relationships.

4.

Run the RNC MML command SET UINTRAFREQHO (CME single configuration: UMTS Radio
Global Configuration Express > HandOver Parameter Configuration > RNC Oriented Intrafrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) to set the parameter related to handover.

16.4.3 MML Command Examples


//Activating Intra Frequency Hard Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_HARD_HO_SWITCH-1;
ADD UINTRAFREQNCELL: RncId=1, CellId=111, NCellRncId=1, NCellId=211,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;

ADD UNRNC: NRncId =2, SHOTRIG=CS_SHO_SWITCH-0&HSPA_SHO_SWITCH0&NON_HSPA_SHO_SWITCH-0, HHOTRIG=ON, SERVICEIND=SUPPORT_CS_AND_PS,


IurExistInd=TRUE, DPX=1, RNCPROTCLVER=R5, STATEINDTMR=20,
TnlBearerType=ATM_TRANS;
ADD UEXT3GCELL: NRncId=2, CellId=311, CellHostType=SINGLE_HOST,
CellName="311", CnOpGrpIndex=0, PScrambCode=256, BandInd=Band1,
UARFCNUplinkInd=TRUE, UARFCNUplink=9750, UARFCNDownlink=10700,
TxDiversityInd=FALSE, LAC=H'2506, CfgRacInd=NOT_REQUIRE, QqualminInd=FALSE,
QrxlevminInd=FALSE, MaxAllowedUlTxPowerInd=FALSE,
CellCapContainerFdd=EDCH_SUPPORT-1, EFachSupInd=FALSE;
ADD UINTRAFREQNCELL: RncId=1, CellId=111, NCellRncId=2, NCellId=311,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;

16.4.4 Activation Observation


1.

On the RNC LMT, click Trace > UMTS Services, and then double-click Uu Interface Trace.
The Uu Interface Trace dialog box is displayed.

2.

Set parameters in the areas Cell Config, Uu Message Type, and Save File. Then, click Submit.

3.

Both UE1 and UE2 are subscribed in HLR to support speech service.

4.

4. Both UE1 and UE2 are in idle mode and camp on the CELL1.

5.

UE1 calls UE2, and the conversation is clear.

6.

UE1 moved from CELL1 to CELL2, through the Trace Date, it can be observed
RRC_MEAS_RPRT message with 1D event that UE1 sends to RNC1.

16.4.5 Deactivation
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS Radio
Global Configuration Express > Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: Modifying RNC Parameters in Batches) to
deselect HO_INTRA_FREQ_HARD_HO_SWITCH from the Handover switch list.

16.4.6 MML Command Examples


//Deactivating Intra Frequency Hard Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_HARD_HO_SWITCH-0;

16.5 WRFD-01061204 HSUPA Mobility Management


This section describes how to activate, verify, and deactivate the optional feature WRFD-01061204
HSUPA Mobility Management.

16.5.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


The feature WRFD-010612 HSUPA Introduction Package must be configured before this feature is
activated.

License
The license "High Speed Uplink Packet Access" on the RNC side has been activated. The license "
the number of NodeBs with HSUPA function enabled" on the NodeB side has been activated. For

details about the license items and how to activate the license, see License Management Feature
Parameter Description.

16.5.2 Activation
The methods of activating intra-frequency, inter-frequency, and inter-RAT handovers are the same for
HSUPA users and R99 users. For the activation procedures for configuring HSUPA Mobility Management,
see the following sections:

16.4 WRFD-020301 Intra Frequency Hard Handover

16.8 WRFD-020302 Inter Frequency Hard Handover Based on Coverage

16.9 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS

Engineering Guidelines in Inter-Frequency Load Balancing Feature Parameter Description

16.11 WRFD-020303 Inter-RAT Handover Based on Coverage

16.12 WRFD-020309 Inter-RAT Handover Based on DL QoS

16.17 WRFD-020305 Inter-RAT Handover Based on Service

16.18 WRFD-020306 Inter-RAT Handover Based on Load

16.5.3 Activation Observation


None.

16.5.4 Deactivation
This feature does not need to be deactivated.

16.6 WRFD-01061404 HSUPA 2ms/10ms TTI Handover


This section describes how to activate, verify, and deactivate the optional feature WRFD-01061404
HSUPA 2ms/10ms TTI Handover.

16.6.1 Requirements

Dependencies on Hardware
Dependencies on RNC Hardware
This feature does not depend on the RNC hardware.

Dependencies on NodeB Hardware

The BTS3812E, BTS3812A, or BTS3812AE is configured with the EBBI, EBOI, EULP, or
EULPd board.

The BBU3806 is configured with the EBBC or EBBCd board.

The BBU3900 is configured with the WBBPb or WBBPd board.


Dependencies on Other Features

The feature WRFD-010614 HSUPA Phase 2 has been configured before this feature is activated.

License

This feature is controlled by the license for the WRFD-010614 HSUPA Phase 2. For details about
this license, see HSUPA Feature Parameter Description.

16.6.2 Activation
This feature is license controlled. It takes effect after its license is activated. For details about how to
activate the license, see License Management Feature Parameter Description.

16.6.3 Activation Observation


This feature does not need to be verified.

16.6.4 Deactivation
This feature does not need to be deactivated.

16.7 WRFD-021200 HCS (Hierarchical Cell Structure)


This section describes how to activate, verify, and deactivate the optional feature WRFD-021200 HCS
(Hierarchical Cell Structure).
After this feature is activated, videophone services can fall back to voice services after being handed over
to the GSM network.

16.7.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
The license "Hierarchical Cell Structure" on the RNC side has been activated. For details about the
license items and how to activate the license, see License Management Feature Parameter
Description.

Other Requirements
To enable videophone services to fall back to voice services, the MSC and UE must comply with
3GPP Release 6. For details, see section 4.3 Core Network procedure in 3GPP TS 23.172 V10.0.0.

16.7.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches).
In this step, select the following check boxes under the HoSwitch(BSC6900,BSC6910) parameter:

HO_ALGO_HCS_SPEED_EST_SWITCH

HO_INTRA_FREQ_SOFT_HO_SWITCH

HO_INTER_FREQ_HARD_HO_SWITCH

HO_INTER_RAT_PS_OUT_SWITCH

HO_INTER_RAT_CS_OUT_SWITCH
In this step, select the CMP_DL_LOAD_BALANCE_SWITCH check box under
the Compatibility Switch2 parameter.

2.

3.

Run the RNC MML command ADD UCELLHCS (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell HCS Parameters; CME batch modification
center: Modifying UMTS Cell Parameters in Batches). In this step, set Use of HCS to USED.
Set the HCS parameters for different types of neighboring cells as follows:

Run the RNC MML command ADD UINTRAFREQNCELL (CME single configuration:
UMTS Cell Configuration Express > Neighboring Cell > Intra-frequency Neighboring Cell;
CME batch modification center: not supported) to add an intra-frequency neighboring cell and
set the HCS parameters.

Run the RNC MML command ADD UINTERFREQNCELL (CME single configuration:
UMTS Cell Configuration Express > Neighboring Cell > Inter-frequency Neighboring Cell;
CME batch modification center: not supported) to add an inter-frequency neighboring cell and
set the HCS parameters.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification
center: not supported) to add an inter-RAT neighboring GSM cell and set the HCS
parameters.

4.

For the cells whose HCS parameters have been set, run the RNC MML command ADD
UCELLHCSHO (CME single configuration: UMTS Cell Configuration Express > Cell Parameters >
Cell Oriented HCS Handover Algorithm Parameters; CME batch modification center: Modifying
UMTS Cell Parameters in Batches). In this step, setSpdEstSwitch to ON.

5.

Run the RNC MML command SET UHCSHO (CME single configuration: UMTS Radio Global
Configuration Express > HandOver Parameter Configuration > RNC Oriented HCS HO Algorithm
Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to set the
RNC-level HCS parameters according to network plan.

16.7.3 MML Command Examples


/*Activating HCS (Hierarchical Cell Structure).*/
//Set HandOver Switch
SET UCORRMALGOSWITCH: HoSwitch=HO_ALGO_HCS_SPEED_EST_SWITCH1&HO_INTRA_FREQ_SOFT_HO_SWITCH-1&HO_INTER_FREQ_HARD_HO_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1&HO_INTER_RAT_CS_OUT_SWITCH-1,
CmpSwitch2=CMP_DL_LOAD_BALANCE_SWITCH-1;
//Set HCS cell to Use of HCS
ADD UCELLHCS: CellId=11, UseOfHcs=USED;
//Add an intra-frequency neighboring cell
ADD UINTRAFREQNCELL: RncId=1, CellId=11, NCellRncId=9, NCellId=100,
SIB11Ind=TRUE, IdleQoffset1sn=0, IdleQoffset2sn=0, SIB12Ind=FALSE,
TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
//Add an inter-frequency neighboring cell
ADD UINTERFREQNCELL:RncId=1, CellId=11, NCellRncId=9, NCellId=100,
CIOOffset=0, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
HOCovPrio=1, BlindHOFlag=FALSE, NPrioFlag=FALSE;
//Add a GSM inter-RAT neighboring cell
ADD U2GNCELL: RncId=1, CellId=11, GSMCellIndex=0, CIOOffset=0, Qoffset1sn=0,
Qrxlevmin=-50, TpenaltyHcsReselect=D0, TempOffset1=D3, BlindHoFlag=TRUE,
BlindHOPrio=30, NPrioFlag=FALSE;

//Set Algorithm Switch for UE Speed Estimation


ADD UCELLHCSHO: CellId=11, SpdEstSwitch=ON;

16.7.4 Activation Observation


To check whether this feature has been activated, perform the following steps:
1.

If the moving speed of a UE is higher than the fast-moving handover threshold (the number of 1D
events reported by the UE in the specified period reaches the preset number), an inter-frequency
or inter-RAT HCS handover is triggered.

2.

If the moving speed of a UE is lower than the slow-moving handover threshold (the number of 1D
events reported by the UE in the specified period is smaller than the slow-moving handover
threshold), slow-moving HCS handover measurement is triggered, and a slow-moving interfrequency or inter-RAT HCS handover is performed.

3.

If a measurement-based inter-frequency or inter-RAT handover is triggered, check whether


compressed mode is started by using a RRC_PH_CH_RECFG message on the Uu interface on
the RNC LMT. If compressed mode is started, this feature is activated.

4.

If an inter-frequency blind handover is triggered, check whether the handover is triggered by


using a RRC_PH_CH_RECFG message on the Uu interface on the RNC LMT. If the handover is
triggered by using the message, this feature is activated.

5.

If an inter-RAT blind handover is triggered, check whether 3G-to-2G handovers are performed on
the Uu and Iu interfaces on the RNC LMT. If 3G-to-2G handovers are performed, this feature is
activated.

To check whether a videophone service has fallen back to a voice service after being handed over to the
GSM network, perform the following steps:
1.

Start Iu Interface Trace and Uu Interface Trace on the RNC LMT.

2.

After video phone services are established, check in the Uu Interface Trace dialog box that the
UE sends to the RNC an RRC_MEAS_RPRT message, which contains the 3A report.

3.

In the Iu Interface Trace dialog box, check that the RNC sends
an RAB_MODIFY_REQ message to the CN. In the RAB_MODIFY_REQ message, the value of
the IE alternativeRABConfigurationRequest is alternative-RAB-configuration-Requested.

16.7.5 Deactivation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step, deselectHO_ALGO_HCS_SPEED_EST_SWITCH from
the HoSwitch parameter.

2.

Run the RNC MML command MOD UCELLHCS (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell HCS Parameters; CME batch modification
center: Modifying UMTS Cell Parameters in Batches). In this step, set Use of HCS to NOT_USED.

3.

Run the RNC MML command MOD UCELLHCSHO (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Oriented HCS Handover Algorithm Parameters;
CME batch modification center: Modifying UMTS Cell Parameters in Batches). In this step,
set SpdEstSwitch to OFF.

16.7.6 MML Command Examples


//Deactivating HCS (Hierarchical Cell Structure).
SET UCORRMALGOSWITCH: HoSwitch=HO_ALGO_HCS_SPEED_EST_SWITCH-0;

MOD UCELLHCS: CellId=11, UseOfHcs=NOT_USED;


MOD UCELLHCSHO: CellId=11, SpdEstSwitch=OFF;

16.8 WRFD-020302 Inter Frequency Hard Handover Based on Coverage


This section describes how to activate, verify, and deactivate the optional feature WRFD-020302 Inter
Frequency Hard Handover Based on Coverage.

16.8.1 When to Use This Feature


This feature is recommended when networks of different frequency bands cover the same area.

16.8.2 Required Information


None.

16.8.3 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
The license "Inter frequency hard handover" on the RNC side has been activated. For details about
the license items and how to activate the license, see License Management Feature Parameter
Description.

Other Requirements
The UE supports relevant measurements and the handover procedure.

16.8.4 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step, selectHO_INTER_FREQ_HARD_HO_SWITCH from
the HandOver Switch drop-down list.

2.

Run the RNC MML command ADD UINTERFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Inter-frequency Neighboring Cell; CME batch
modification center: not supported) to add an inter-frequency neighboring cell.

3.

Run the RNC MML command ADD UCELLINTERFREQHOCOV (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented Coverage Based Interfrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying UMTS Cell Parameters in Batches) (cell level) or SET
UINTERFREQHOCOV (CME single configuration: UMTS Radio Global Configuration Express >
HandOver Parameter Configuration > RNC Oriented Coverage Based Inter-frequency Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying RNC Parameters
in Batches) (RNC level) to configure parameters related to coverage-based inter-frequency hard
handover.

16.8.5 MML Command Examples

//Activating Inter Frequency Hard Handover Based on Coverage


SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1
ADD UINTERFREQNCELL:RncId=1, CellId=1, NCellRncId=9, NCellId=100, CIOOffset=0,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, HOCovPrio=1,
BlindHOFlag=FALSE, NPrioFlag=FALSE;
ADD UCELLINTERFREQHOCOV: CellId=1, InterFreqReportMode=PERIODICAL_REPORTING,
InterFreqMeasTime=60;

16.8.6 Activation Observation


1.

Click to display Uu Interface Trace on the RNC LMT.

2.

Check whether the RNC has sent the UE an RRC_MEAS_CTRL message and the traced
message contains thresholds for triggering events 2D and 2F and the reporting mode.

3.

Attenuate signals in the current cell that the UE accesses to trigger reporting of event 2D by the
UE.

4.

Check whether the RNC has sent the UE an RRC_MEAS_RPRT message and the traced
message contains an event 2D measurement report shown in Figure 16-1.
Figure 16-1 Event 2D measurement report

5.

After the event 2D measurement report is reported, check whether the RNC has sent the UE
an RRC_MEAS_CTRL message and the traced message contains the information element
interFrequencyMeasurement, as shown in Figure 16-2.

Figure 16-2 Inter-frequency measurement control message

6.

After the inter-frequency measurement control message is reported, check whether the RNC has
sent the UE an RRC_PH_CH_RECFG message, and the UE has sent the RNC
RRC_PH_CH_RECFG_CMP message, as shown in Figure 16-3 and Figure 16-4.
Figure 16-3 Physical channel reconfiguration message

Figure 16-4 Physical channel reconfiguration complete message

16.8.7 Deactivation
Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS Radio
Global Configuration Express > Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: Modifying RNC Parameters in Batches). In this step,
deselect HO_INTER_FREQ_HARD_HO_SWITCH fromHandOver Switch.

16.8.8 MML Command Examples


//Deactivating Inter Frequency Hard Handover Based on Coverage
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-0;

16.8.9 Performance Monitoring


After the WRFD-020302 Inter Frequency Hard Handover Based on Coverage feature is activated, collect
statistics about the following counters in the live network.

VS.RRC.MrRpt.2D
VS.HHO.AttInterFreqOut.CS.TrigRscp
VS.HHO.AttInterFreqOut.CS.TrigEcNo
VS.HHO.AttInterFreqOut.PS.TrigRscp
VS.HHO.AttInterFreqOut.PS.TrigEcNo
When a UE is located at the cell edge, it reports event 2D to trigger a coverage-based inter-frequency or
inter-RAT hard handover.

If the value of the VS.RRC.MrRpt.2D counter is small, the number of coverage-based interfrequency hard handovers triggered in a measurement period is small, which indicates that the gains
provided by this feature are not obvious.

If the value of the counter is large and is similar to the value of


the VS.HHO.AttInterFreqOut.CS.TrigRscp,
VS.HHO.AttInterFreqOut.CS.TrigEcNo,VS.HHO.AttInterFreqOut.PS.TrigRscp,
or VS.HHO.AttInterFreqOut.PS.TrigEcNo counter, the inter-frequency hard handovers that
happened in the measurement period are mainly coverage-based inter-frequency hard handovers,
which indicates that the gains provided by this feature are obvious.

If the value of the counter is large and is much greater than the value of
the VS.HHO.AttInterFreqOut.CS.TrigRscp,
VS.HHO.AttInterFreqOut.CS.TrigEcNo,VS.HHO.AttInterFreqOut.PS.TrigRscp,

or VS.HHO.AttInterFreqOut.PS.TrigEcNo counter, both coverage-based inter-frequency hard


handovers and coverage-based inter-RAT hard handovers happened in the measurement period.

16.9 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS


This section describes how to activate, verify, and deactivate the optional feature WRFD-020304 Inter
Frequency Hard Handover Based on DL QoS.

16.9.1 When to Use This Feature


This feature is recommended when signal fading is serious and the traffic load is high in the live network.

16.9.2 Required Information


Collect statistics about the following counters before deploying the WRFD-020304 Inter Frequency Hard
Handover Based on DL QoS feature:

VS.AMR.DL.RateDown: indicates the number of times the downlink data rates of narrowband
AMR speech services are reduced in a cell.

VS.AMRWB.DLRateDown: indicates the number of times the downlink data rates of wideband
AMR speech services are reduced in a cell.

VS.DCCC.AttDownsizing.DL.Cov: indicates the number of downlink DCH DCCC downsizing


attempts based on different strategies (coverage or QoS) in the best cell on which the UE camps.

During the link stability control of CS services and R99 PS BE services, rate reduction and handover are
triggered in sequence. If the number of rate reductions for CS services and R99 PS BE services
(VS.AMR.DL.RateDown, VS.AMRWB.DLRateDown, or VS.DCCC.AttDownsizing.DL.Cov) is small, the
downlink quality did not deteriorate. In this case, do not enable the WRFD-020304 Inter Frequency Hard
Handover Based on DL QoS feature. If the number of rate reductions for CS services and R99 PS BE
services is large, enable the WRFD-020304 Inter Frequency Hard Handover Based on DL QoS feature.

16.9.3 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


The feature WRFD-020302 Inter Frequency Hard Handover Based on Coverage must be configured
before this feature is activated.

License
The license "Inter Frequency Hard Handover Based on DL QoS " on the RNC side has been
activated. For details about the license items and how to activate the license, seeLicense
Management Feature Parameter Description.

16.9.4 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to activate the inter-frequency hard handover.

2.

Run the RNC MML command ADD UINTERFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Inter-frequency Neighboring Cell; CME batch
modification center: not supported) to add an inter-frequency neighboring cell.

3.

Run the RNC MML command ADD UCELLINTERFREQHOCOV (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented Coverage Based Interfrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying UMTS Cell Parameters in Batches) (cell level) or SET
UINTERFREQHOCOV (CME single configuration: UMTS Radio Global Configuration Express >
HandOver Parameter Configuration > RNC Oriented Coverage Based Inter-frequency Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying RNC Parameters
in Batches) (RNC level) to configure parameters related to DL-QoS-based inter-frequency hard
handover.

4.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
activate inter-frequency hard handover based on downlink QoS for BE services.

5.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center:Modifying RNC Parameters in Batches) to
activate inter-frequency hard handover based on downlink QoS for AMR and AMR-WB services.

6.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center:Modifying RNC Parameters in Batches) to
activate inter-frequency hard handover based on downlink QoS for VP services.

16.9.5 MML Command Examples


//Activating Inter Frequency Hard Handover Based on DL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1;
ADD UINTERFREQNCELL: RncId=1, CellId=1, NCellRncId=9, NCellId=100,
CIOOffset=0, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
HOCovPrio=1, BlindHOFlag=FALSE, NPrioFlag=FALSE;
ADD UCELLQOSHO: CellId=111, DlRscpQosHyst=5, DLQosMcTimerLen=20,
ULQosMcTimerLen=20;
SET UQOSACT: BEQosPerform=YES, BeDlAct1=InterFreqHO;
SET UQOSACT: AMRQosPerform=YES, DlQosAmrInterFreqHoSwitch=YES,
DlQosWAmrInterFreqHoSwitch=YES;
SET UQOSACT: VPQosPerform=YES, DlQosVpInterFreqHoSwitch=YES;

16.9.6 Activation Observation


1.

Log in to the RNC LMT and start Uu Interface Trace.

2.

Ensure that the RNC sends an NBAP_DEDI_MEAS_INIT_REQ message to the NodeB and the
message contains the event E and event F parameters.

3.

Ensure that the NodeB sends an NBAP_DEDIC_MEAS_RPRT message to the RNC and the
message contains the event E parameter.

4.

Ensure that the RNC sends an RRC_MEAS_CTRL message to the NodeB to start eventtriggered or periodic inter-frequency measurement.

5.

16.9.7 Deactivation
1.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement

Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
deactivate inter-frequency hard handover based on downlink QoS for BE services.
2.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
deactivate inter-frequency hard handover based on downlink QoS for AMR and AMR-WB services.

3.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
deactivate inter-frequency hard handover based on downlink QoS for VP services.

16.9.8 MML Command Examples


//Deactivating Inter Frequency Hard Handover Based on DL QoS
RMV UCELLQOSHO: CellId=111;
SET UQOSACT: BEQosPerform=NO; or SET UQOSACT: BEQosPerform=YES, BeDlAct1=None,
BeDlAct2=None, BeDlAct3=None;
SET UQOSACT: AMRQosPerform=NO; or SET UQOSACT: AMRQosPerform=YES,
DlQosAmrInterFreqHoSwitch=NO, DlQosWAmrInterFreqHoSwitch=NO;
SET UQOSACT: VPQosPerform=NO; or SET UQOSACT: VPQosPerform=YES,
DlQosVpInterFreqHoSwitch=NO;

16.10 Inter Frequency Hard Handover Based on UL QoS


This section describes how to activate, verify, and deactivate the feature Inter Frequency Hard Handover
Based on UL QoS.

16.10.1 When to Use This Feature


This feature is recommended when signal fading is serious and the traffic load is high in the live network.

16.10.2 Required Information


Collect statistics about the following counters before deploying the WRFD-020304 Inter Frequency Hard
Handover Based on UL QoS feature:

VS.AMR.UL.RateDown: indicates the number of times the uplink data rates of narrowband AMR
speech services are reduced in a cell.

VS.AMRWB.ULRateDown: indicates the number of times the uplink data rates of wideband AMR
speech services are reduced in a cell.

VS.DCCC.AttDownsizing.UL.Cov: indicates the number of uplink DCH DCCC downsizing


attempts based on different strategies (coverage or QoS) in the best cell on which the UE camps.

During the link stability control of CS services and R99 PS BE services, rate reduction and handover are
triggered in sequence. If the number of rate reductions for CS services and R99 PS BE services
(VS.AMRWB.ULRateDown, VS.AMRWB.ULRateDown, or VS.DCCC.AttDownsizing.UL.Cov) is small, the
uplink quality did not deteriorate. In this case, do not enable the Inter Frequency Hard Handover Based
on UL QoS feature. If the number of rate reductions for CS services and R99 PS BE services is large,
enable the Inter Frequency Hard Handover Based on UL QoS feature.

16.10.3 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
The license "Inter Frequency Hard Handover Based on UL QoS " on the RNC side has been
activated. For details about the license items and how to activate the license, seeLicense
Management Feature Parameter Description.

16.10.4 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to activate the inter-frequency hard handover.

2.

Run the RNC MML command ADD UINTERFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Inter-frequency Neighboring Cell; CME batch
modification center: not supported) to add an inter-frequency neighboring cell.

3.

Run the RNC MML command ADD UCELLINTERFREQHOCOV (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented Coverage Based Interfrequency Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying UMTS Cell Parameters in Batches) (cell level) or SET
UINTERFREQHOCOV (CME single configuration: UMTS Radio Global Configuration Express >
HandOver Parameter Configuration > RNC Oriented Coverage Based Inter-frequency Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying RNC Parameters
in Batches) (RNC level) to configure parameters related to UL-QoS-based inter-frequency hard
handover.

4.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
activate inter-frequency hard handover based on uplink QoS for BE services.

5.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center:Modifying RNC Parameters in Batches) to
activate inter-frequency hard handover based on uplink QoS for AMR and AMR-WB services.

6.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center:Modifying RNC Parameters in Batches) to
activate inter-frequency hard handover based on uplink QoS for VP services.

16.10.5 MML Command Examples


//Activating Inter Frequency Hard Handover Based on UL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1; ADD
UINTERFREQNCELL: RncId=1, CellId=1, NCellRncId=9, NCellId=100, CIOOffset=0,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, HOCovPrio=1,
BlindHOFlag=FALSE, NPrioFlag=FALSE; ADD UCELLQOSHO: CellId=111,
DlRscpQosHyst=5, DLQosMcTimerLen=20, ULQosMcTimerLen=20; SET UQOSACT:
BEQosPerform=YES, BeUlAct1=InterFreqHO; SET UQOSACT: AMRQosPerform=YES,
UlQosAmrInterFreqHoSwitch=YES, UlQosWAmrInterFreqHoSwitch=YES; SET UQOSACT:
VPQosPerform=YES, UlQosVpInterFreqHoSwitch=YES;

16.10.6 Activation Observation


1.
2.

Log in to the RNC LMT and start Uu Interface Trace.


Ensure that the RNC sends an RRC_MEAS_CTRL message to the UE and the message
contains the event 6A parameter, as shown in Figure 16-5.
Figure 16-5 RRC_MEAS_CTRL message

3.

Ensure that the UE sends an RRC_MEAS_RPRT message to the RNC and the message
contains the event 6A parameter, as shown in Figure 16-6.

Figure 16-6 RRC_RB_RECFG message

4.

Ensure that the RNC sends an RRC_MEAS_CTRL message to the NodeB to start eventtriggered or periodic inter-frequency measurement.

16.10.7 Deactivation
1.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
deactivate inter-frequency hard handover based on uplink QoS for BE services.

2.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
deactivate inter-frequency hard handover based on uplink QoS for AMR and AMR-WB services.

3.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
deactivate inter-frequency hard handover based on uplink QoS for VP services.

16.10.8 MML Command Examples


//Deactivating Inter Frequency Hard Handover Based on UL QoS
RMV UCELLQOSHO: CellId=111;
SET UQOSACT: BEQosPerform=NO;
SET UQOSACT: BEQosPerform=YES, BeUlAct1=None, BeUlAct2=None, BeUlAct3=None;
SET UQOSACT: AMRQosPerform=NO;
SET UQOSACT: AMRQosPerform=YES, UlQosAmrInterFreqHoSwitch=NO,
UlQosWAmrInterFreqHoSwitch=NO;
SET UQOSACT: VPQosPerform=NO;
SET UQOSACT: VPQosPerform=YES, UlQosVpInterFreqHoSwitch=NO;

16.11 WRFD-020303 Inter-RAT Handover Based on Coverage

This section describes how to activate, verify, and deactivate the optional feature WRFD-020303 InterRAT Handover Based on Coverage.
After this feature is activated, videophone services can fall back to voice services after being handed over
to the GSM network.

16.11.1 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
The license "Coverage Based Inter-RAT Handover Between UMTS and GSM/GPRS" on the RNC
side has been activated. For details about the license items and how to activate the license,
see License Management Feature Parameter Description.

Other Requirements
The UE supports relevant measurements and the handover procedure.
To enable videophone services to fall back to voice services, the MSC and UE must comply with
3GPP Release 6. For details, see section 4.3 Core Network procedure in 3GPP TS 23.172 V10.0.0.

16.11.2 Activation
NOTE:
This feature can be batch activated using the CME. For detailed operations, see the following section in
the CME product documentation or online help: Managing the CME > CME Guidelines > Enhanced
Feature Management > Feature Operation and Maintenance.
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step,
selectHO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH from
the HandOver Switch list.

2.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to add an inter-frequency neighboring GSM cell.

3.

Run the RNC MML command ADD UCELLINTERRATHOCOV (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell Oriented Coverage Based Inter-rat Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying UMTS Cell
Parameters in Batches) (cell level) or SET UINTERRATHOCOV (CME single configuration: UMTS
Radio Global Configuration Express > HandOver Parameter Configuration > RNC Oriented
Coverage based Inter-rat Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) (RNC level) to configure parameters related to
coverage-based inter-RAT handover to GSM.

4.

Run the RNC MML command MOD UTYPRABBASIC (CME single configuration: UMTS Radio
Global Configuration Express > Typical Service Configuration > Basic Information for
Typical Traffic Radio Access Bearer; CME batch modification center: not supported). In this step,
set Service Handover Indicator toHO_TO_GSM_SHOULD_NOT_BE_PERFORM.

16.11.3 MML Command Examples


//Activating Inter-RAT Handover Based on Coverage
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1;

16.11.4 Activation Observation


To check whether this feature has been activated, perform the following steps:
1.

Attenuate signals in the current cell that the UE accesses to trigger reporting of event 2D by the
UE.

2.

Click to display Uu Interface Trace on the RNC LMT. Under Uu Message Type,
select RRC_MEAS_RPRT.

3.

Check whether event 2D shown in Figure 16-7 has been reported in the traced messages.
Figure 16-7 Event 2D measurement report

4.

Click to display Uu Interface Trace on the RNC LMT. Under Uu Message Type,
select RRC_MEAS_CTRL.

5.

Check in the traced messages whether the RNC has sent the UE an inter-RAT measurement
control message shown in Figure 16-8.
Figure 16-8 Inter-RAT measurement control message

NOTE:

To verify the measurement-based inter-RAT handover triggered by uplink QoS of UEs, you need
to Run the RNC MML command SET UQOSACT to turn on the QoS switches of different service
types and attenuate the signals of the current cell. Check whether UEs send the uplink QoS
measurement reports to the RNC. The verification steps are the same as those for event 2D.

The inter-RAT blind handover triggered by event 1F is a special application. You need to measure
the pilot strength and quality scope of the best cell where the blind handover is to be triggered.
Generally, the inter-RAT blind handover is not needed and therefore does not need to be verified.

To check whether a videophone service has fallen back to a voice service after being handed over to the
GSM network, perform the following steps:
1.

Start Iu Interface Trace and Uu Interface Trace on the RNC LMT.

2.

After video phone services are established, check in the Uu Interface Trace dialog box that the
UE sends to the RNC an RRC_MEAS_RPRT message, which contains the 3A report.

3.

In the Iu Interface Trace dialog box, check that the RNC sends
an RAB_MODIFY_REQ message to the CN. In the RAB_MODIFY_REQ message, the value of
the IE alternativeRABConfigurationRequest is alternative-RAB-configuration-Requested.

16.11.5 Deactivation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to deactivate this feature.

2.

Run the RNC MML command RMV UCELLINTERRATHOCOV (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell Oriented Coverage Based Inter-rat Handover
Measurement Algorithm Parameters; CME batch modification center: not supported) (cell level)
or SET UINTERRATHOCOV (CME single configuration: UMTS Radio Global Configuration
Express > HandOver Parameter Configuration > RNC Oriented Coverage based Inter-rat Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying RNC Parameters
in Batches) (RNC level) to remove or restore the parameters related to coverage-based inter-RAT
handover to GSM.

16.11.6 MML Command Examples


//Deactivating Inter-RAT Handover Based on Coverage
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH0&HO_INTER_RAT_PS_OUT_SWITCH-0;

16.12 WRFD-020309 Inter-RAT Handover Based on DL QoS


This section describes how to activate, verify, and deactivate the optional feature WRFD-020309 InterRAT Handover Based on DL QoS.

16.12.1 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


The feature WRFD-020302 Inter Frequency Hard Handover Based on Coverage must be configured
before this feature is activated.

License
The license "Inter-RAT Handover Based on DL QoS" on the RNC side has been activated. For
details about the license items and how to activate the license, see License Management Feature
Parameter Description.

Other Requirements
The UE supports relevant measurements and the handover procedure.

16.12.2 Activation
1.

(Optional) Run the RNC MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch modification
center: Modifying RNC Parameters in Batches). In this step,
selectHO_INTER_RAT_PS_OUT_SWITCH under the HandOver Switch parameter.
NOTE:
Before activating this feature, perform 1 if HO_INTER_RAT_PS_OUT_SWITCH are not turned
on. You can run the RNC MML command LST UCORRMALGOSWITCH to check whether this
switch have been turned on.

2.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to add an inter-RAT neighboring cell.

3.

Run the RNC MML command SET UQOSHO (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC Oriented QoS Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying RNC Parameters
in Batches) to set RNC-level parameters related to Inter-RAT Handover Based on DL QoS.

4.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
turn on QoS switches for different traffic classes.

16.12.3 MML Command Examples


//Activating Inter-RAT Handover Based on DL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_PS_OUT_SWITCH-1;
SET UQOSACT: BEQosPerform=YES, AMRQosPerform=YES, VPQosPerform=YES,
BeDlAct1=InterRatHO, DlQosAmrInterRatHoSwitch=YES,
DlQosWAmrInterRatHoSwitch=YES;

16.12.4 Activation Observation


1.

Log in to the RNC LMT and start Uu Interface Trace.

2.

Ensure that the RNC sends an NBAP_DEDI_MEAS_INIT_REQ message to the NodeB and the
message contains the event E and event F parameters.

3.

Ensure that the NodeB sends an NBAP_DEDIC_MEAS_RPRT message to the RNC and the
message contains the event E parameter.

4.

Ensure that the RNC sends an RRC_MEAS_CTRL message to the NodeB to start eventtriggered or periodic inter-frequency measurement.

16.12.5 Deactivation

1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step,
deselectHO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH under
the HandOver Switch parameter.
NOTE:
Do not
perform 1 if HO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH have
been turned on before activating this feature.

2.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
turn off QoS switches for different traffic classes.

16.12.6 MML Command Examples


//Deactivating Inter-RAT Handover Based on DL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH0&HO_INTER_RAT_PS_OUT_SWITCH-0;
SET UQOSACT: BEQosPerform=NO, AMRQosPerform=NO, VPQosPerform=NO;

16.13 Inter-RAT Handover Based on UL QoS


This section describes how to activate, verify, and deactivate the optional feature WRFD-020309 InterRAT Handover Based on DL QoS.

16.13.1 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
The license "Inter-RAT Handover Based on UL QoS" on the RNC side has been activated. For
details about the license items and how to activate the license, see License Management Feature
Parameter Description.

Other Requirements
The UE supports relevant measurements and the handover procedure.

16.13.2 Activation
1.

(Optional) Run the RNC MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch modification
center: Modifying RNC Parameters in Batches). In this step,
selectHO_INTER_RAT_PS_OUT_SWITCH under the HandOver Switch parameter.
NOTE:

Before activating this feature, perform 1 if HO_INTER_RAT_PS_OUT_SWITCH are not turned


on. You can run the RNC MML command LST UCORRMALGOSWITCH to check whether this
switch have been turned on.
2.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to add an inter-RAT neighboring cell.

3.

Run the RNC MML command SET UQOSHO (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC Oriented QoS Handover
Measurement Algorithm Parameters; CME batch modification center: Modifying RNC Parameters
in Batches) to set RNC-level parameters related to Inter-RAT Handover Based on UL QoS.

4.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
turn on QoS switches for different traffic classes.

16.13.3 MML Command Examples


//Activating Inter-RAT Handover Based on UL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1; SET UQOSACT: BEQosPerform=YES,
AMRQosPerform=YES, VPQosPerform=YES, BeUlAct1=InterRatHO,
UlQosAmrInterRatHoSwitch=YES, UlQosWAmrInterRatHoSwitch=YES;

16.13.4 Activation Observation


1.
2.

Log in to the RNC LMT and start Uu Interface Trace.


Ensure that the RNC sends to the NodeB an NBAP_DEDI_MEAS_INIT_REQ message, which
carries the event E parameter, as shown in Figure 16-9.
Figure 16-9 NBAP_DEDI_MEAS_INIT_REQ message

3.

Ensure that the NodeB reports to the RNC an NBAP_DEDI_MEAS_RPRT message, which
carries the event E parameter, as shown in Figure 16-10.

Figure 16-10 RRC_RB_RECFG message

4.

Ensure that the RNC sends to the UE an RRC_MEAS_CTRL message and starts inter-frequency
measurement of the event or period type. Then, check that the corresponding traced message
indicates that the RNC has sent the inter-frequency measurement control message to the UE, as
shown in Figure 16-11.
Figure 16-11 RRC_RB_RECFG message

16.13.5 Deactivation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step,
deselectHO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH under
the HandOver Switch parameter.

NOTE:
Do not
perform 1 if HO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH have
been turned on before activating this feature.
2.

Run the RNC MML command SET UQOSACT (CME single configuration: UMTS Radio Global
Configuration Express > QOS Parameter Configuration > RNC-Oriented QoS Enhancement
Algorithm Parameters; CME batch modification center: Modifying RNC Parameters in Batches) to
turn off QoS switches for different traffic classes.

16.13.6 MML Command Examples


//Deactivating Inter-RAT Handover Based on UL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH0&HO_INTER_RAT_PS_OUT_SWITCH-0;
SET UQOSACT: BEQosPerform=NO, AMRQosPerform=NO, VPQosPerform=NO;

16.14 WRFD-020308 Inter-RAT Handover Phase 2


This section describes how to activate, verify, and deactivate the optional feature WRFD-020308 InterRAT Handover Phase 2.

16.14.1 Requirements

Dependencies on Hardware
The RNC should support the NACC RIM procedure and PS handovers. When RIM messages are
exchanged through the eCoordinator, the RNC should support the RIM procedure that is
implemented through Huawei proprietary eCoordinator.

Dependencies on Other Features


This feature is required only when one or several of the following inter-RAT handover features are
introduced:

WRFD-020303 Inter-RAT Handover Based on Coverage

WRFD-020305 Inter-RAT Handover Based on Service

WRFD-020306 Inter-RAT Handover Based on Load

WRFD-021200 HCS (Hierarchical Cell Structure)

License
This feature is not under license control.

Other Requirements

The UE must support the NACC procedure and PS handover.

The BSC must support the NACC RIM (RAN Information Management) procedure and
PS handover. When RIM messages are exchanged through the eCoordinator, the RNC must
support the RIM procedure that is implemented through Huawei proprietary eCoordinator.

The SGSN must support the NACC procedure and PS handover.When RIM messages
are exchanged through the CN, the SGSN must support the NACC procedure.

16.14.2 Deployment
For details about how to activate, verify, and deactivate this feature, see the following sections:

16.15 WRFD-02030801 NACC(Network Assisted Cell Change)

16.16 WRFD-02030802 PS Handover Between UMTS and GPRS

16.15 WRFD-02030801 NACC(Network Assisted Cell Change)


This section describes how to activate, verify, and deactivate the optional feature WRFD-02030801
NACC(Network Assisted Cell Change).

16.15.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


The configurations of the features on which this feature depends are complete. This feature
depends on the feature WRFD-020308 PS Inter-RAT Handover Phase 2.

License
The license "NACC(Network Assisted Cell Change)" on the RNC side has been activated. For
details about the license items and how to activate the license, see License Management Feature
Parameter Description.

Other Requirements

The UE must support the NACC procedure and comply with 3GPP Release 5 or later.

The BSC must support the NACC RIM (RAN Information Management) procedure.

When RIM messages are exchanged through the CN, the SGSN must comply with 3GPP
Release 5 or later and support the NACC procedure.

When RIM messages are exchanged through the eCoordinator, the BSC, RNC, and
Huawei proprietary eCoordinator must support the RIM procedure that is implemented through
the eCoordinator.

16.15.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to open the following switches in theHandOver switch parameter:

HO_INTER_RAT_PS_OUT_SWITCH

HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH

HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH
NOTE:

When the HO_INTER_RAT_PS_OUT_SWITCH is turned on,


the HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH does not take effect.

2.

Run the RNC MML command ADD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches)(for new neighboring cell) or MOD UEXT2GCELL(CME single configuration: Object Group
> UMTS Service Configuration and Maintenance Management > External Cell Configuration >
RNC 2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) (for the existing neighboring cell) to set Inter-RAT cell support RIM indicator to TRUE.

3.

(Optional) If RIM messages are exchanged through Huawei proprietary eCoordinator, run the
RNC MML command SET URRCTRLSWITCH, and select theRIM_ON_ECO_SWITCH check box
under the PROCESSSWITCH5 parameter.

16.15.3 MML Command Examples


//Activating NACC
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH1&HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH-0&HO_INTER_RAT_PS_OUT_SWITCH-1;
//Setting Inter-RAT cell support RIM indicator to TRUE
MOD UEXT2GCELL: GSMCellIndex=1, SuppRIMFlag=TRUE;
//Setting the RIM_ON_ECO_SWITCH under the PROCESSSWITCH5 parameter to on
SET URRCTRLSWITCH: PROCESSSWITCH5=RIM_ON_ECO_SWITCH-1;

16.15.4 Activation Observation


To enable RIM messages to be exchanged through the CN, do as follows:
1.

Run the RNC MML command LST UCORRMALGOSWITCH to check the settings of the PS interRAT handover, NACC, and Relocation switches.

2.

Run the RNC MML command LST UEXT2GCELL to check whether the inter-RAT neighboring cell
supports the RIM procedure.

3.

Trace messages over the Iu interface to check whether the RNC has sent a
RANAP_DIR_INFO_TRANSFER message to the CN to request RIM information.

4.

Trace messages over the Iu interface to check whether the RNC has received a
RANAP_DIR_INFO_TRANSFER message from the CN as a response to the request

message.
5.

Trace messages over the Uu interface to check whether there is an


RRC_CELL_CHANGE_ORDER_FROM_UTRAN message that carries system information on the

GSM side.
To enable RIM messages to be exchanged through Huawei proprietary eCoordinator, do as follows:
1.

Run the RNC MML command LST UCORRMALGOSWITCH and check the settings of the PS
inter-RAT handover, NACC, and Relocation switches.

2.

Run the RNC MML command LST UEXT2GCELL and check whether the inter-RAT neighboring
cell supports the RIM procedure.

3.

Run the RNC MML command LST URRCTRLSWITCH and check whether the BSC supports the
RIM procedure that is implemented through the eCoordinator.

4.

Check the signaling messages over the Sg interface before the UMTS-to-GSM handover is
performed. If an RNC DIRECT INFORMATION TRANSFER message has been sent to the
eCoordinator and an ECO DIRECT INFORMATION TRANSFER message sent by the
eCoordinator has been received over the Sg interface, the WRFD-02030801 NACC(Network
Assisted Cell Change) feature takes effect.
NOTE:

To implement this feature, the UE should support NACC. Therefore, the NACC-supportive UEs are
required for activation.

16.15.5 Deactivation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to setHO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH in
the HandOver switch parameter to 0.

2.

Run the RNC MML command MOD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to set Inter-RAT cell support RIM indicator toFALSE.

3.

If RIM messages are exchanged through Huawei proprietary eCoordinator, run the RNC MML
command SET URRCTRLSWITCH, and deselect the RIM_ON_ECO_SWITCHcheck box under
the PROCESSSWITCH5 parameter.

16.15.6 MML Command Examples


//Deactivating NACC(Network Assisted Cell Change)
MOD UEXT2GCELL: SuppRIMFlag=FALSE;
//Setting RIM_ON_ECO_SWITCH under the PROCESSSWITCH5 parameter to off
SET URRCTRLSWITCH: PROCESSSWITCH5=RIM_ON_ECO_SWITCH-0;

16.16 WRFD-02030802 PS Handover Between UMTS and GPRS


This section describes how to activate, verify, and deactivate the optional feature WRFD-02030802 PS
Handover Between UMTS and GPRS.

16.16.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


The configurations of the features on which this feature depends are complete. This feature
depends on the feature WRFD-020308 PS Inter-RAT Handover Phase 2.

License

The license "PS Handover Between UMTS and GPRS" on the RNC side has been activated. For
details about the license items and how to activate the license, see License Management Feature
Parameter Description.

Other Requirements
The UE, GSM BSC, and SGSN must support the PS handover.
If RIM messages are exchanged through Huawei proprietary eCoordinator, the BSC and RNC must
connect to the same eCoordinator and be able to exchange RIM messages with the eCoordinator.

16.16.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to open the following switches in theHandOver switch parameter:

HO_INTER_RAT_PS_OUT_SWITCH

HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH

2.

Run the RNC MML command ADD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to add a neighboring GSM cell to the UMTS coverage and to set the Inter-RAT cell
support PS HO indicator parameter to TRUE.

3.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to add a neighboring GSM cell for the UMTS cell.

4.

(Optional) Run the RNC MML command SET UINTERRATHOCOV (CME single configuration:
UMTS Radio Global Configuration Express > HandOver Parameter Configuration > RNC Oriented
Coverage based Inter-rat Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) to set inter-RAT handover measurement related
parameters.

16.16.3 MML Command Examples


//Activating PS Handover between UMTS and GPRS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1;
ADD UEXT2GCELL: GSMCellIndex=1, GSMCellName="GSMCELL1", NBscIndex=1,
LdPrdRprtSwitch=ON, MCC="460", MNC="01", CnOpGrpIndex=1, LAC=1,
CfgRacInd=REQUIRE, RAC=1, CID=1, NCC=1, BCC=1, BcchArfcn=512,
RatCellType=GPRS, UseOfHcs=NOT_USED, SuppPSHOFlag=TRUE;
ADD U2GNCELL: RNCId=1, CellId=100, GSMCellIndex=1;
SET UINTERRATHOCOV: InterRatReportMode=PERIODICAL_REPORTING,
FilterCoefOf2D2F=D4, InterRATFilterCoef=D6;

16.16.4 Activation Observation


1.

Run the RNC MML command LST UCORRMALGOSWITCH to check the status of PS inter-RAT
handover switch and the Relocation HO switch.

2.

Run the RNC MML command LST UEXT2GCELL to ensure the inter-RAT cell supports PS
Handover.

Run the RNC MML command LST UINTERRATHOCOV to check inter-RAT handover measurement
related parameters.

16.16.5 Deactivation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to setHO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH in
the HandOver switch parameter to 0.

2.

Run the RNC MML command MOD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to set the SuppPSHOFlag parameter toFALSE.

16.16.6 MML Command Examples


//Deactivating PS Handover between UMTS and GPRS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH-0;
MOD UEXT2GCELL: SuppPSHOFlag=FALSE;

16.17 WRFD-020305 Inter-RAT Handover Based on Service


This section describes how to activate, verify, and deactivate the optional feature WRFD-020305 InterRAT Handover Based on Service.
After this feature is activated, videophone services can fall back to voice services after being handed over
to the GSM network.

16.17.1 Requirements

Dependencies on Hardware
This feature does not depend on the hardware.

Dependencies on Other Features


This feature does not depend on other features.

License
The license "Inter system Service Handover" on the RNC side has been activated. For details about
the license items and how to activate the license, see License Management Feature Parameter
Description.

Other Requirements
To enable videophone services to fall back to voice services, the MSC and UE must comply with
3GPP Release 6. For details, see section 4.3 Core Network procedure in 3GPP TS 23.172 V10.0.0.

16.17.2 Activation
NOTE:
This feature can be batch activated using the CME. For detailed operations, see the following section in
the CME product documentation or online help: Managing the CME > CME Guidelines > Enhanced
Feature Management > Feature Operation and Maintenance.

1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches). In this step,
selectHO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH from
the HandOver Switch list.

2.

Run the RNC MML command ADD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to add a neighboring GSM cell.

3.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to set neighbor relationships with the neighboring GSM cell.

4.

Run the RNC MML command ADD UCELLHOCOMM (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Oriented Handover Common Algorithm
Parameters; CME batch modification center: Modifying UMTS Cell Parameters in Batches). In this
step, set Inter-RAT CS handover switch or Inter-RAT PS handover switch to ON.

5.

Run the RNC MML command ADD UCELLINTERRATHONCOV (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented None-Coverage Based Interrat Handover Measurement Algorithm Parameters; CME batch modification center: Modifying
UMTS Cell Parameters in Batches) (cell level) or SET UINTERRATHONCOV (CME single
configuration: UMTS Radio Global Configuration Express > HandOver Parameter Configuration >
RNC Oriented None-Coverage based Inter-rat Handover Measurement Algorithm Parameters;
CME batch modification center: Modifying RNC Parameters in Batches) (RNC level) to configure
parameters related to non-coverage-based inter-frequency handover to GSM.

16.17.3 MML Command Examples


//Activating Inter-RAT Handover Based on Service
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1;
ADD UCELLHOCOMM: CellId=111, CSServiceHOSwitch=ON, PSServiceHOSwitch=ON;

16.17.4 Activation Observation


To check whether this feature has been activated, perform the following steps:
1.

Click to display Uu Interface Trace on the RNC LMT. Under Uu Message Type,
select RRC_MEAS_CTRL.

2.

After services are set up, view in the traced messages whether the RNC has sent the UE an
inter-frequency measurement control message shown in Figure 16-12.

Figure 16-12 Inter-frequency measurement control message

To check whether a videophone service has fallen back to a voice service after being handed over to the
GSM network, perform the following steps:
1.

Start Iu Interface Trace and Uu Interface Trace on the RNC LMT.

2.

After video phone services are established, check in the Uu Interface Trace dialog box that the
UE sends to the RNC an RRC_MEAS_RPRT message, which contains the 3A report.

3.

In the Iu Interface Trace dialog box, check that the RNC sends
an RAB_MODIFY_REQ message to the CN. In the RAB_MODIFY_REQ message, the value of
the IE alternativeRABConfigurationRequest is alternative-RAB-configuration-Requested.

16.17.5 Deactivation
Run the RNC MML command MOD UCELLHOCOMM (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Oriented Handover Common Algorithm Parameters; CME
batch modification center: Modifying UMTS Cell Parameters in Batches). In this step, set Inter-RAT CS
handover switch or Inter-RAT PS handover switch to OFF.

16.17.6 MML Command Examples


//Deactivating Inter-RAT Handover Based on Service
MOD UCELLHOCOMM: CellId=111, CSServiceHOSwitch=OFF, PSServiceHOSwitch=OFF;

16.18 WRFD-020306 Inter-RAT Handover Based on Load


This section describes how to activate, verify, and deactivate the optional feature WRFD-020306 InterRAT Handover Based on Load.
After this feature is activated, videophone services can fall back to voice services after being handed over
to the GSM network.

16.18.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


If this feature is used for HSDPA or HSUPA load control, the feature WRFD-010610 HSDPA
Introduction Package or WRFD-010612 HSUPA Introduction Package has been configured
correspondingly before this feature is activated.

License
The license "Inter system Load Handover" on the RNC side has been activated. For details about
the license items and how to activate the license, see License Management Feature Parameter
Description.

Other Requirements
To enable videophone services to fall back to voice services, the MSC and UE must comply with
3GPP Release 6. For details, see section 4.3 Core Network procedure in 3GPP TS 23.172 V10.0.0.

16.18.2 Activation
NOTE:
This feature can be batch activated using the CME. For detailed operations, see the following section in
the CME product documentation or online help: Managing the CME > CME Guidelines > Enhanced
Feature Management > Feature Operation and Maintenance.
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to activate the inter-RAT handover. In this step, select
the HO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH check boxes
under the parameter HandOver Switch.

2.

Run the RNC MML command SET UCORRMALGOSWITCH. In this step, select
the HO_INTER_RAT_RNC_SERVICE_HO_SWITCH check box under the HandOver
Switch parameter.

3.

Run the RNC MML command MOD UTYPRABBASIC. In this step, set Service Handover
Indicator to HO_TO_GSM_SHOULD_BE_PERFORM.
NOTE:
Setting Service Handover Indicator to HO_TO_GSM_SHOULD_BE_PERFORM facilitates feature
verification during lab tests. On a live network, set this parameter according to the network plan.
Ensure that the parameter setting is consistent with the LDR action-related parameter setting
mentioned in 11.

4.

Enable the uplink air-interface LDR algorithm by selecting the UL_UU_LDR check box under
the Switch for Cell Load Control parameter in the RNC MML command ADD
UCELLALGOSWITCH.

5.

Enable the downlink air-interface LDR algorithm by selecting the DL_UU_LDR check box under
the Switch for Cell Load Control parameter in the RNC MML commandADD
UCELLALGOSWITCH.

6.

Enable the cell credit LDR algorithm by selecting the CELL_CREDIT_LDR check box under
the Switch for Cell Load Control parameter in the RNC MMLcommand ADD
UCELLALGOSWITCH.

7.

Enable the credit load control algorithm at the NodeB or cell group level by selecting
the NODEB_CREDIT_LDR_SWITCH or LCG_CREDIT_LDR_SWITCH check box under the load
control algorithm switch parameter in the RNC MML command SET ULDCALGOPARA.

8.

Enable the credit load congestion control algorithm at the NodeB or cell group level by selecting
the NODEB_CREDIT_LDR or LCG_CREDIT_LDR check box under the NodeB LDC algorithm
switch parameter in the RNC MML command ADD UNODEBALGOPARA.
NOTE:
Performing 4 to 8 facilitates feature verification during lab tests. On a live network, set the
parameters according to the network plan.

9.

Run the RNC MML command ADD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to add the information about a GSM cell.

10.

Run the RNC MML command ADD U2GNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to add the GSM cell as a neighboring cell of the UMTS cell.

11.

Run the RNC MML command ADD UCELLLDR (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell LDR Algorithm Parameters; CME batch
modification center: Modifying UMTS Cell Parameters in Batches) to set the inter-RAT handover
policy for the UMTS cell. In this step, set DL LDR fourth action toCSInterRatShouldBeLDHO(CS
domain inter-rat should be load handover), DL LDR fifth
action to PSInterRatShouldBeLDHO(PS domain inter-rat should be load handover), UL LDR
fourth action to CSInterRatShouldBeLDHO(CS domain inter-rat should be load handover),
and UL LDR fifth action toPSInterRatShouldBeLDHO(PS domain inter-rat should be load
handover).
NOTE:
Setting UL/DL LDR first action to CSInterRatShouldBeLDHO(CS domain inter-rat should be
load handover) and UL/DL LDR second action toPSInterRatShouldBeLDHO(PS domain interrat should be load handover) facilitates feature verification during lab tests. On a live network, set
these parameters according to the network plan.

12.

Run the RNC MML command MOD UCELLLDM. In this step, set the following parameters to
appropriate values: UL LDR trigger threshold, UL LDR release threshold, DL LDR trigger threshold,
DL LDR release threshold, and DL State Trans Hysteresis threshold.

13.

Run the RNC MML command MOD UNODEBLDR. In this step, set UL LDR Credit SF reserved
threshold to an appropriate value for the credit LDR algorithm at the NodeB or cell group level.

14.

Run the RNC MML command SET ULDCPERIOD. In this step, set LDR period timer length to
an appropriate value.

15.

Run the RNC MML command ADD UCELLINTERRATHONCOV (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented None-Coverage Based Interrat Handover Measurement Algorithm Parameters; CME batch modification center: Modifying
UMTS Cell Parameters in Batches) (at the cell level) orSET UINTERRATHONCOV (CME single
configuration: UMTS Radio Global Configuration Express > HandOver Parameter Configuration >
RNC Oriented None-Coverage based Inter-rat Handover Measurement Algorithm Parameters;
CME batch modification center: Modifying RNC Parameters in Batches) (at the RNC level) to
configure parameters related to non-coverage-based inter-frequency handover to GSM.

16.18.3 MML Command Examples

//Activating Inter-RAT Handover Based on Load


SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1& HO_INTER_RAT_RNC_SERVICE_HO_SWITCH-1;
MOD UTYPRABBASIC: RabIndex=1, SHInd=HO_TO_GSM_SHOULD_BE_PERFORM;
MOD UCELLALGOSWITCH: CellId=11, NBMLdcAlgoSwitch=UL_UU_LDR-1&DL_UU_LDR1&CELL_CREDIT_LDR-1;
SET ULDCALGOPARA: LdcSwitch=NODEB_CREDIT_LDR_SWITCH-1&LCG_CREDIT_LDR_SWITCH-1;
ADD UEXT2GCELL: GSMCellIndex=2, GSMCellName="2", NBscIndex=2,
LdPrdRprtSwitch=OFF, MCC="460", MNC="07", CnOpGrpIndex=1, LAC=H'0012,
CfgRacInd=REQUIRE, RAC=H'01, CID=2, NCC=2, BCC=2, BcchArfcn=1000,
RatCellType=GSM, UseOfHcs=NOT_USED;
ADD U2GNCELL: RncId=1, CellId=2, GSMCellIndex=2, BlindHoFlag=TRUE,
BlindHOPrio=1, NPrioFlag=FALSE;
ADD UCELLLDR: CellId=1, DlLdrFourthAction=CSInterRatShouldBeLDHO,
DlLdrFifthAction=PSInterRatShouldBeLDHO,
UlLdrFourthAction=CSInterRatShouldBeLDHO,
UlLdrFifthAction=PSInterRatShouldBeLDHO;
MOD UCELLLDM: CellId=11, UlLdrTrigThd=55, UlLdrRelThd=45, DlLdrTrigThd=70,
DlLdrRelThd=60, DlLdTrnsHysTime=1000;
SET ULDCPERIOD: LdrPeriodTimerLen=10;
ADD UCELLINTERRATHONCOV: CellId=1;

16.18.4 Activation Observation


To check whether this feature has been activated, perform the following steps:
1.

Initiate Iu interface message tracing and Uu interface message tracing on the RNC LMT.

2.

Use a UE in the UMTS cell to call another UE in the same cell. The call is set up successfully.

3.

Run the RNC MML command MOD UCELLLDM and set


the UlLdrTrigThd(BSC6900,BSC6910) and DlLdrTrigThd(BSC6900,BSC6910) parameters to
reduce the uplink and downlink LDR threshold, respectively.

The following messages can be traced on the Iu interface: the


RANAP_RELOCATION_REQUIRED message from the RNC to the CN, and the
RANAP_RELOCATION_COMMAND message from the CN to the RNC.

The following message can be traced on the Uu interface: the


RRC_HO_FROM_UTRAN_CMD_GSM message from the RNC to the UE.

The following messages can be traced on the Iu interface: the


RANAP_RELOCATION_REQUIRED message from the RNC to the CN, the
RANAP_RELOCATION_COMMAND message from the CN to the RNC, the
RANAP_IU_RELEASE_COMMAND message from the CN to the RNC, and the
RANAP_IU_RELEASE_COMPLETE message from the RNC to the CN.

To check whether a videophone service has fallen back to a voice service after being handed over to the
GSM network, perform the following steps:
1.

Start Iu Interface Trace and Uu Interface Trace on the RNC LMT.

2.

After video phone services are established, check in the Uu Interface Trace dialog box that the
UE sends to the RNC an RRC_MEAS_RPRT message, which contains the 3A report.

3.

In the Iu Interface Trace dialog box, check that the RNC sends
an RAB_MODIFY_REQ message to the CN. In the RAB_MODIFY_REQ message, the value of
the IE alternativeRABConfigurationRequest is alternative-RAB-configuration-Requested.

16.18.5 Deactivation
1.

Run the RNC MML command MOD UCELLLDR (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell LDR Algorithm Parameters; CME batch
modification center: Modifying UMTS Cell Parameters in Batches) to deactivate the load-based
handover. In this step, set DL LDR fourth action, DL LDR fifth action,UL LDR fourth action,
and UL LDR fifth action to NoAct.

2.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to deactivate the inter-RAT handover. In this step, deselect
the HO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH check boxes
under the parameter HandOver Switch.

16.18.6 MML Command Examples


//Deactivating Inter-RAT Handover Based on Load
MOD UCELLLDR: CellId=1, DlLdrFourthAction=NoAct, DlLdrFifthAction=NoAct,
UlLdrFourthAction=NoAct, UlLdrFifthAction=NoAct;
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH0&HO_INTER_RAT_PS_OUT_SWITCH-0;

16.19 WRFD-020310 3G/2G Common Load Management


This section describes how to activate, verify, and deactivate the optional feature WRFD-020310 3G/2G
Common Load Management.

16.19.1 Requirements

Dependencies on Hardware
This feature does not have any special requirements for hardware.

Dependencies on Other Features


This feature is required only when one of the following features is available:

WRFD-020305 Inter-RAT Handover Based on Service

WRFD-020306 Inter-RAT Handover Based on Load

WRFD-021200 HCS (Hierarchical Cell Structure)

WRFD-020400 DRD Introduction Package

WRFD-020308 Inter-RAT Handover Phase 2


License

The license "3G/2G Common Load Management" on the RNC side has been activated. For details
about the license items and how to activate the license, see License Management Feature
Parameter Description.

Other Requirements
The CN and BSS must support this feature.
Before deploying this feature, ensure that the Handover Request Acknowledge messages sent from
GSM to UMTS carry load information of GSM cells, because the RNC needs to determine whether
to allow a UMTS-to-GSM handover based on load information of GSM cells.

16.19.2 Activation
1.

Run the RNC MML command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: Modifying RNC
Parameters in Batches) to enable the inter-RAT handover. In this step,
select HO_INTER_RAT_CS_OUT_SWITCH and HO_INTER_RAT_PS_OUT_SWITCH through
the HandOver Switch.

2.

Run the RNC MML command SET UINTERRATHONCOV (CME single configuration: UMTS
Radio Global Configuration Express > HandOver Parameter Configuration > RNC Oriented NoneCoverage based Inter-rat Handover Measurement Algorithm Parameters; CME batch modification
center: Modifying RNC Parameters in Batches) to enable the 3G/2G common load management
function. In this step, select the Send Load Info to GSM Ind and NCOV Reloc Ind Based on
GSM Cell Load.

3.

Run the RNC MML command ADD UEXT2GCELL (CME single configuration: Object Group >
UMTS Service Configuration and Maintenance Management > External Cell Configuration > RNC
2G External Cell; CME batch modification center: Modifying RNC External Cell Parameters in
Batches) to add a GSM cell neighboring to the UMTS coverage.

4.

Run the RNC MML command ADD U2GNCELL(CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > GSM Neighboring Cell; CME batch modification center:
not supported) to set a GSM cell as the UMTS cell's neighboring cell.

16.19.3 MML Command Examples


//Activating 3G/2G Common Load Management
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH1&HO_INTER_RAT_PS_OUT_SWITCH-1;
SET UINTERRATHONCOV: SndLdInfo2GsmInd=ON, NcovHoOn2GldInd=ON;
ADD UEXT2GCELL: GSMCellIndex=2, GSMCellName="2", NBscIndex=2,
LdPrdRprtSwitch=OFF, MCC="460", MNC="07", CnOpGrpIndex=1,
LAC=H'0012, CfgRacInd=REQUIRE, RAC=H'01, CID=2, NCC=2, BCC=2, BcchArfcn=1000,
RatCellType=GSM, UseOfHcs=NOT_USED;
ADD U2GNCELL: RncId=1, CellId=2, GSMCellIndex=2, BlindHoFlag=TRUE,
BlindHOPrio=1, NPrioFlag=FALSE;

16.19.4 Activation Observation


1.

Run the RNC MML command LST UINTERRATHONCOV to check whether the parameters Send
Load Info to GSM Ind and NCOV Reloc Ind based on GSM cell load are set to ON.

2.

Run the RNC MML command LST U2GNCELL to ensure the inter-RAT neighboring cell for the
GSM system is added correctly.
NOTE:

Consult Huawei engineers about the verification solution to obtain professional technical support.

16.19.5 Deactivation
Run the RNC MML command SET UINTERRATHONCOV (CME single configuration: UMTS Radio
Global Configuration Express > HandOver Parameter Configuration > RNC Oriented None-Coverage
based Inter-rat Handover Measurement Algorithm Parameters; CME batch modification center: Modifying
RNC Parameters in Batches) to set the parameter Send Load Info to GSM Ind to OFF and the
parameter NCOV Reloc Ind based on GSM cell load to OFF.

16.19.6 MML Command Examples


//Deactivating 3G/2G Common Load Management
SET UINTERRATHONCOV: SndLdInfo2GsmInd=OFF, NcovHoOn2GldInd=OFF;

16.20 WRFD-01061006 HSDPA Mobility Management


This section describes how to activate, observe, and deactivate the optional feature WRFD-01061006
HSDPA Mobility Management.

16.20.1 Requirements

Dependencies on Hardware
None

Dependencies on Other Features


The configurations of the features that are required by this feature are complete. This feature
requires the WRFD-010610 HSDPA Introduction Package feature.

License
The licenses "HSDPA RRM package 1" and "HSDPA function" on the NodeB side have been
activated. For details about how to activate licenses, see License Management Feature Parameter
Description.

16.20.2 Activation
The methods of activating intra-frequency, inter-frequency, and inter-RAT handovers are the same for
HSDPA UEs and R99 UEs. For details, see the following sections:

16.4 WRFD-020301 Intra Frequency Hard Handover

16.8 WRFD-020302 Inter Frequency Hard Handover Based on Coverage

16.9 WRFD-020304 Inter Frequency Hard Handover Based on DL QoS

Engineering guidelines chapter in the document Inter-Frequency Load Balancing Feature


Parameter Description

16.11 WRFD-020303 Inter-RAT Handover Based on Coverage

16.12 WRFD-020309 Inter-RAT Handover Based on DL QoS

16.17 WRFD-020305 Inter-RAT Handover Based on Service

16.18 WRFD-020306 Inter-RAT Handover Based on Load

16.20.3 Activation Observation


None.

16.20.4 Deactivation
This feature does not need to be deactivated.

17 Parameters
Table 17-1 Parameter description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RsvS B SET No Non


witch4 S UAL ne e
C GOR
6 SVPA
9 RA
0
0

Meaning: RRM algorithm reserved U32 Switch Para 4. The 32bit parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_4_BIT1,
RESERVED_SWITCH_4_BIT2,
RESERVED_SWITCH_4_BIT3,
RESERVED_SWITCH_4_BIT4,
RESERVED_SWITCH_4_BIT5,
RESERVED_SWITCH_4_BIT6,
RESERVED_SWITCH_4_BIT7,
RESERVED_SWITCH_4_BIT8,
RESERVED_SWITCH_4_BIT9,
RESERVED_SWITCH_4_BIT10,
RESERVED_SWITCH_4_BIT11,
RESERVED_SWITCH_4_BIT12,
RESERVED_SWITCH_4_BIT13,
RESERVED_SWITCH_4_BIT14,
RESERVED_SWITCH_4_BIT15,
RESERVED_SWITCH_4_BIT16,
RESERVED_SWITCH_4_BIT17,
RESERVED_SWITCH_4_BIT18,
RESERVED_SWITCH_4_BIT19,
RESERVED_SWITCH_4_BIT20,
RESERVED_SWITCH_4_BIT21,
RESERVED_SWITCH_4_BIT22,
RESERVED_SWITCH_4_BIT23,
RESERVED_SWITCH_4_BIT24,
RESERVED_SWITCH_4_BIT25,
RESERVED_SWITCH_4_BIT26,
RESERVED_SWITCH_4_BIT27,
RESERVED_SWITCH_4_BIT28,
RESERVED_SWITCH_4_BIT29,
RESERVED_SWITCH_4_BIT30,
RESERVED_SWITCH_4_BIT31,
RESERVED_SWITCH_4_BIT32
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range: RESERVED_SWITCH_4_BIT1,


RESERVED_SWITCH_4_BIT2,
RESERVED_SWITCH_4_BIT3,
RESERVED_SWITCH_4_BIT4,
RESERVED_SWITCH_4_BIT5,
RESERVED_SWITCH_4_BIT6,
RESERVED_SWITCH_4_BIT7,
RESERVED_SWITCH_4_BIT8,
RESERVED_SWITCH_4_BIT9,
RESERVED_SWITCH_4_BIT10,
RESERVED_SWITCH_4_BIT11,
RESERVED_SWITCH_4_BIT12,
RESERVED_SWITCH_4_BIT13,
RESERVED_SWITCH_4_BIT14,
RESERVED_SWITCH_4_BIT15,
RESERVED_SWITCH_4_BIT16,
RESERVED_SWITCH_4_BIT17,
RESERVED_SWITCH_4_BIT18,
RESERVED_SWITCH_4_BIT19,
RESERVED_SWITCH_4_BIT20,
RESERVED_SWITCH_4_BIT21,
RESERVED_SWITCH_4_BIT22,
RESERVED_SWITCH_4_BIT23,
RESERVED_SWITCH_4_BIT24,
RESERVED_SWITCH_4_BIT25,
RESERVED_SWITCH_4_BIT26,
RESERVED_SWITCH_4_BIT27,
RESERVED_SWITCH_4_BIT28,
RESERVED_SWITCH_4_BIT29,
RESERVED_SWITCH_4_BIT30,
RESERVED_SWITCH_4_BIT31,
RESERVED_SWITCH_4_BIT32
Default Value:
RESERVED_SWITCH_4_BIT1:0,RESERVED_SWITCH_4_BI
T2:0,RESERVED_SWITCH_4_BIT3:0,RESERVED_SWITCH_
4_BIT4:0,RESERVED_SWITCH_4_BIT5:0,RESERVED_SWI
TCH_4_BIT6:0,RESERVED_SWITCH_4_BIT7:0,RESERVED
_SWITCH_4_BIT8:0,RESERVED_SWITCH_4_BIT9:0,RESER
VED_SWITCH_4_BIT10:0,RESERVED_SWITCH_4_BIT11:0,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_4_BIT12:0,RESERVED_SWITCH_4_B
IT13:0,RESERVED_SWITCH_4_BIT14:0,RESERVED_SWIT
CH_4_BIT15:0,RESERVED_SWITCH_4_BIT16:0,RESERVED
_SWITCH_4_BIT17:0,RESERVED_SWITCH_4_BIT18:0,RES
ERVED_SWITCH_4_BIT19:0,RESERVED_SWITCH_4_BIT2
0:0,RESERVED_SWITCH_4_BIT21:0,RESERVED_SWITCH_
4_BIT22:0,RESERVED_SWITCH_4_BIT23:0,RESERVED_S
WITCH_4_BIT24:0,RESERVED_SWITCH_4_BIT25:0,RESER
VED_SWITCH_4_BIT26:0,RESERVED_SWITCH_4_BIT27:0,
RESERVED_SWITCH_4_BIT28:0,RESERVED_SWITCH_4_B
IT29:0,RESERVED_SWITCH_4_BIT30:0,RESERVED_SWIT
CH_4_BIT31:0,RESERVED_SWITCH_4_BIT32:0
RsvS B SET No Non
witch4 S UAL ne e
C GOR
6 SVPA
9 RA
1
0

Meaning: RRM algorithm reserved U32 Switch Para 4. The 32bit parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_4_BIT1,
RESERVED_SWITCH_4_BIT2,
RESERVED_SWITCH_4_BIT3,
RESERVED_SWITCH_4_BIT4,
RESERVED_SWITCH_4_BIT5,
RESERVED_SWITCH_4_BIT6,
RESERVED_SWITCH_4_BIT7,
RESERVED_SWITCH_4_BIT8,
RESERVED_SWITCH_4_BIT9,
RESERVED_SWITCH_4_BIT10,
RESERVED_SWITCH_4_BIT11,
RESERVED_SWITCH_4_BIT12,
RESERVED_SWITCH_4_BIT13,
RESERVED_SWITCH_4_BIT14,
RESERVED_SWITCH_4_BIT15,
RESERVED_SWITCH_4_BIT16,
RESERVED_SWITCH_4_BIT17,
RESERVED_SWITCH_4_BIT18,
RESERVED_SWITCH_4_BIT19,
RESERVED_SWITCH_4_BIT20,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_4_BIT21,
RESERVED_SWITCH_4_BIT22,
RESERVED_SWITCH_4_BIT23,
RESERVED_SWITCH_4_BIT24,
RESERVED_SWITCH_4_BIT25,
RESERVED_SWITCH_4_BIT26,
RESERVED_SWITCH_4_BIT27,
RESERVED_SWITCH_4_BIT28,
RESERVED_SWITCH_4_BIT29,
RESERVED_SWITCH_4_BIT30,
RESERVED_SWITCH_4_BIT31,
RESERVED_SWITCH_4_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_4_BIT1,
RESERVED_SWITCH_4_BIT2,
RESERVED_SWITCH_4_BIT3,
RESERVED_SWITCH_4_BIT4,
RESERVED_SWITCH_4_BIT5,
RESERVED_SWITCH_4_BIT6,
RESERVED_SWITCH_4_BIT7,
RESERVED_SWITCH_4_BIT8,
RESERVED_SWITCH_4_BIT9,
RESERVED_SWITCH_4_BIT10,
RESERVED_SWITCH_4_BIT11,
RESERVED_SWITCH_4_BIT12,
RESERVED_SWITCH_4_BIT13,
RESERVED_SWITCH_4_BIT14,
RESERVED_SWITCH_4_BIT15,
RESERVED_SWITCH_4_BIT16,
RESERVED_SWITCH_4_BIT17,
RESERVED_SWITCH_4_BIT18,
RESERVED_SWITCH_4_BIT19,
RESERVED_SWITCH_4_BIT20,
RESERVED_SWITCH_4_BIT21,
RESERVED_SWITCH_4_BIT22,
RESERVED_SWITCH_4_BIT23,
RESERVED_SWITCH_4_BIT24,
RESERVED_SWITCH_4_BIT25,
RESERVED_SWITCH_4_BIT26,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_4_BIT27,
RESERVED_SWITCH_4_BIT28,
RESERVED_SWITCH_4_BIT29,
RESERVED_SWITCH_4_BIT30,
RESERVED_SWITCH_4_BIT31,
RESERVED_SWITCH_4_BIT32
Default Value:
RESERVED_SWITCH_4_BIT1:0,RESERVED_SWITCH_4_BI
T2:0,RESERVED_SWITCH_4_BIT3:0,RESERVED_SWITCH_
4_BIT4:0,RESERVED_SWITCH_4_BIT5:0,RESERVED_SWI
TCH_4_BIT6:0,RESERVED_SWITCH_4_BIT7:0,RESERVED
_SWITCH_4_BIT8:0,RESERVED_SWITCH_4_BIT9:0,RESER
VED_SWITCH_4_BIT10:0,RESERVED_SWITCH_4_BIT11:0,
RESERVED_SWITCH_4_BIT12:0,RESERVED_SWITCH_4_B
IT13:0,RESERVED_SWITCH_4_BIT14:0,RESERVED_SWIT
CH_4_BIT15:0,RESERVED_SWITCH_4_BIT16:0,RESERVED
_SWITCH_4_BIT17:0,RESERVED_SWITCH_4_BIT18:0,RES
ERVED_SWITCH_4_BIT19:0,RESERVED_SWITCH_4_BIT2
0:0,RESERVED_SWITCH_4_BIT21:0,RESERVED_SWITCH_
4_BIT22:0,RESERVED_SWITCH_4_BIT23:0,RESERVED_S
WITCH_4_BIT24:0,RESERVED_SWITCH_4_BIT25:0,RESER
VED_SWITCH_4_BIT26:0,RESERVED_SWITCH_4_BIT27:0,
RESERVED_SWITCH_4_BIT28:0,RESERVED_SWITCH_4_B
IT29:0,RESERVED_SWITCH_4_BIT30:0,RESERVED_SWIT
CH_4_BIT31:0,RESERVED_SWITCH_4_BIT32:0
PerfE
nhanc
eSwitc
h2

B
S
C
6
9
0
0

SET
UCO
RRM
PARA

W
RF
D02
11
01
W
RF
D01
06
14
03

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)

Meaning: 1. PERFENH_RCS_PS_DL_ON_DCH_SWITCH:
Whether the PS service in the RCS-e service is carried on the
DCH in the downlink. When this switch is turned off, the
channel bearer and downlink rate of the PS service in the RCS-e
service in the downlink are unlimited. When this switch is turned
on, the PS service in the RCS-e service can only be carried on
the DCH in the downlink and the downlink rate cannot exceed
the maximum downlink rate of the PS service in the RCS-e
service. For the maximum downlink rate of the PS service in the
RCS-e service, see "PsRcsDlDchRate" in the "SET UFRC"
command. 2.
PERFENH_HSUPA_CAP_CHG_HRETRY_LMT_SWITCH:
Whether the RNC prevents HSPA retry when the NodeB reports

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D02
02
03
W
RF
D02
03
03
W
RF
D14
02
18
W
RF
D15
02
17
W
RF
D02
04
00
W
RF
D02
05
03
W
RF

HS
UP
A
2ms
TTI
Inte
r
RN
C
Soft
Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Ser
vice
Bas
ed
PS
Han
dov
er
fro
m
UM
TS

Description

that a cell does not support HSUPA due to high CPU load on the
DSP. This switch is turned off by default. OFF: This switch is
turned off. When the NodeB reports that the cell does not
support HSUPA services, the RNC does not trigger retry to the
HSPA channel in the following scenarios:The current cell
support the channel retry from the DCH to the E-DCH.The
current cell support channel retries from DCH to the E-DCH and
the HSDSCH. ON: This switch is turned on. When the NodeB
reports that the cell does not support HSUPA services, the RNC
does not trigger retry to the HSPA channel during the DCH to EDCH channel retry. 3.
PERFENH_MC_OPT_AFTER_RETRANS_CHG_SWITCH:
Policy used when the RNC receives a request for changing the
target number of retransmissions during an E-DCH-to-DCH
(E2D) channel migration. ON: This switch is turned on. Upon
receiving the request for changing the target number of
retransmissions, the RNC continues the channel migration
procedure and then updates measurement control. OFF: This
switch is turned off. Upon receiving the request for changing the
target number of retransmissions, the RNC instantly updates
measurement control and then performs the channel migration.
However, this increases the call drop rate. 4.
PERFENH_CSOVERH_H2D_RBID_CHG_SWITCH: Whether
the RNC changes the radio bearer identity when CS services are
handed over from E-DCHs or HS-DSCHs to DCHs. This switch
is turned off by default. When this switch is turned on, the RNC
changes the radio bearer identity. When this switch is turned off,
the RNC does not change the radio bearer identity. For details,
see section 8.6.4.2 in 3GPP TS 25.331 V8.4.0. 5.
PERFENH_RRC_DRD_FAILED_RED_GSM_SWITCH:
Whether the RNC carries the information about the configured
neighboring GSM cells in the RRC CONNECTION REJECT
message when neighboring GSM cells are configured during an
RRC inter-RAT redirection based on admission failures. For UEs
of 3GPP Release 6 or a later version, when this switch is turned
on, the RNC carries the information about the configured
neighboring GSM cells in the RRC CONNECTION REJECT
message. When this switch is turned off, the RNC does not carry
the information about the configured neighboring GSM cells in

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
06
05
W
RF
D15
02
20
W
RF
D01
06
10
W
RF
D02
04
00
03
W
RF
D01
06
12
W
RF
D01
06
12
03
W
RF

to
LTE
Loa
d
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
DR
D
Intr
odu
ctio
n
Pac
kag
e
Out
er
Loo
p
Po
wer
Con
trol
SR
NS
Rel
ocat
ion
Intr

Description

the RRC CONNECTION REJECT message. 6.


PERFENH_IRAT_COV_HO_NCELL_PRE_SWITCH: Whether
high-priority neighboring cells or frequencies are preferred
during coverage-based inter-RAT handovers. When this switch is
turned on, high-priority neighboring cells or frequencies are
preferred. If neighboring cells or frequencies have the same
priority, those with better signal quality are preferred. If their
signal quality is the same, the first selected neighboring cell or
frequency is the target cell or frequency. For UMTS-to-GSM
handovers, the neighboring cell with a smaller value of the
"HOPrio" parameter in the "ADD U2GNCELL" command is
preferentially selected as the target cell. For UMTS-to-LTE
redirections, the frequency with a greater value of the
"NPriority" parameter in the "ADD UCELLNFREQPRIOINFO"
command is preferentially selected as the target frequency. When
this switch is turned off, only signal quality is considered. For
UMTS-to-GSM handovers, the neighboring cell with better
signal quality is preferentially selected as the target cell. For
UMTS-to-LTE redirections, the frequency with better quality is
preferentially selected as the target frequency. 7.
PERFENH_LTE_NCELL_SEL_OPT_SWITCH: Whether to
optimize the list for measured neighboring LTE cells in the
measurement control message. When this switch is turned on, the
RNC filters out the list for measured neighboring LTE cells
according to the RNC-level parameters, cell capability, and UE
capabilities in handovers and redirections to the LTE network.
When this switch is turned off, the RNC does not filter out the
list for measured neighboring LTE cells. 8.
PERFENH_GSM_NCELL_SEL_OPT_SWITCH: Scope for
matching the neighboring cells in measurement reports during
handovers to GSM cells when there are multiple cells in the
active set and the HO_MC_NCELL_COMBINE_SWITCH
switch is turned on. In case of neighboring combination, when
this switch is turned on, the RNC matches the neighboring cells
in measurement reports with neighboring cells of all cells in the
current active set. When this switch is turned off, the RNC
matches the neighboring cells in measurement reports only with
the best cell's neighboring cells. 9.
PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITCH:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
01
34
W
RF
D01
06
19
W
RF
D02
01
29
W
RF
D01
06
09
02
W
RF
D02
14
00
W
RF
D02
03
06

odu
ctio
n
Pac
kag
e
Cov
erag
e
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
HS
DP
A
Intr
odu
ctio
n
Pac
kag
e
Inte
r
Syst
em
Red
irec
t
HS

Description

Whether to select the best target frequency during a frequencybased redirection from UMTS to LTE. When this switch is
turned on, the selected target frequency is used as the best
frequency if the measurement report contains multiple
neighboring cells that work at the same frequency. 10.
PERFENH_ICMP_ACCELERATOR_OPT_SWITCH : Switch
for the enhanced algorithm of accelerating the rate for
responding to control messages. This parameter is a professional
parameter and therefore you must configure this parameter under
the instruction of Huawei technical support.For RTT(round-trip
time) tests, the recommended value is ON. In other scenarios, the
recommended value is OFF. 11.
PERFENH_MULTI_PS_DCCC_SWITCH: Whether to allocate
the RLC parameters corresponding to the 2 ms TTI to the
services that are not reconfigured during the reconfiguration
procedure and have a data rate higher than 2048 kbit/s. The 2048
kbit/s is the maximum data rate supported by the 10 ms TTI.
When this switch is turned on, the RNC allocates such services
the RLC parameters corresponding to the 2 ms TTI. When this
switch is turned off, the RNC does not allocate such services
these parameters. 12.
PERFENH_CHL_CHG_FAIL_MC_OLPC_OPT_SWITCH:
Whether to use invalid measurement control parameters and
power control parameters on the MAC-d entity again if a UE in
the CELL_DCH state fails to switch channels and then
experiences a channel fallback. When this switch is turned on,
the RNC uses these parameters again for such a UE. When this
switch is turned off, the RNC does not use these parameters
again for such a UE. 13.
PERFENH_SET2MBR_ALLOW_D2F_SWITCH: Whether to
allow CELL-DCH-to-CELL_FACH state transitions when the
PS BE services of a UE fail to be reconfigured with an MBR and
the UE periodically requests the MBR. When this switch is
turned on, the UE is allowed to perform CELL-DCH-toCELL_FACH state transitions in the preceding scenario. When
this switch is turned off, the UE is not allowed to perform these
state transitions. 14.
PERFENH_RAB_REL_WITH_PS_D2F_OPT_SWITCH:
Processing option for a low-rate PS service when the cell update

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UP
A
Intr
odu
ctio
n
Pac
kag
e
HS
UP
A
Po
wer
Con
trol
Pus
h to
Talk
CS
voic
e
ove
r
HS
PA/
HS
PA+
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to

Description

procedure overlaps the service release procedure of a CS or PS


service in combined services that also include the low-rate PS
service.When this switch is turned on, the parameter specifying
the status of the low-rate PS service is correctly configured in the
proceeding scenario to prevent a call drop.When this switch is
turned off, the previously mentioned parameter is incorrectly
configured in the proceeding scenario. This will result in a call
drop.For this parameter, please note the following: A low-rate PS
service is a service whose maximum data rate is less than the
values of the "UlBeTraffDecThs" and "DlBeTraffDecThs"
parameters. When a service in combined services that include a
low-rate PS service is being released, the UE is instructed to
perform a state transition from CELL_DCH to CELL_FACH.
15. PERFENH_DRNC_CU_WITHOUT_EXTCELL_SWITCH:
This switch applies to the following two scenarios: Scenario 1: A
UE sends a CELL UPDATE message with a cause value of
"radio link failure" or "RLC unrecoverable error" in a drift RNC
(DRNC) cell that is not configured as a neighboring cell of the
UE's SRNC cell using the "ADD UEXT3GCELL" command.
This switch controls whether the serving RNC (SRNC)
reestablishes a radio link for the UE in this scenario. When this
switch is set to on, the SRNC uses the DSCR procedure to
reestablish a radio link for UEs processing PS BE only services;
the SRNC reestablishes a radio link for UEs processing services
other than PS BE only through the cell update procedure. When
this switch is set to off, the SRNC directly releases the RRC
connection of the UE. Scenario 2: A UE in the CELL_DCH state
sends a cell update request in a DRNC cell after the SRNC
triggers a call reestablishment. The DRNC cell has been
configured as a neighboring cell of the UE's SRNC cell using the
"ADD UEXT3GCELL" command, UE's services are carried
over HSPA channels in the DRNC cell but the SRNC is not
configured with the HSPA capability of the DRNC cell. This
switch controls whether the SRNC can correctly process the cell
update request in this scenario. When this switch is set to on, the
SRNC can correctly process the cell update request. When this
switch is set to off, the SRNC cannot correctly process the cell
update request and as a result, call drops occur. 16.
PERFENH_HO_NODEB_UP_RES_LIMIT_E2D_SWITCH:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
LTE
Co
mbi
nati
on
of
One
CS
Ser
vice
and
One
PS
Ser
vice
Dir
ect
Sig
nali
ng
Con
nect
ion
Reesta
blis
hme
nt
(DS
CR)
Inte
rRA
T
Han
dov
er
Bas
ed

Description

Whether the RNC re-attempts to apply for DCH resources when


the NodeB sends to the RNC cause value not-enough-user-planeprocessing-resources during the request of E-DCH or HS-DSCH
resources for an intra-RAT handover. When this switch is turned
on, the RNC re-attempts to apply for the DCH resources in the
preceding scenario. When this switch is turned off, the RNC
stops applying for any channel resources. 17.
PERFENH_LTE_NCELL_FILTE_OPT_SWITCH: Whether the
RNC filters out neighboring LTE cells based on the principle of
preferentially selecting a maximum of four LTE FDD EARFCNs
and four LTE TDD EARFCNs when the following conditions are
met: 1. The active set contains more than one cell. 2. Each cell is
configured with multiple neighboring LTE cells. 3.
HO_MC_NCELL_COMBINE_SWITCH of the "HoSwitch"
parameter in the "SET UCORRMALGOSWITCH" command
and HO_MC_LTE_NCELL_COMBINE_SWITCH of the
"HoSwitch1" parameter in the "SET UCORRMALGOSWITCH"
command are turned on. When this switch is turned on, the RNC
filters out the neighboring LTE cells based on the principle of
preferentially selecting a maximum of four LTE FDD EARFCNs
and four LTE TDD EARFCNs, preferentially selects the
neighboring LTE cells with the largest number of times the LTE
cells are configured as the neighboring cells for different cells in
the active set until the number of the selected neighboring LTE
cells meets the specifications, and then filters out the excessive
neighboring LTE cells to obtain the candidate neighboring cell
list. When this switch is turned off, the RNC selects the
neighboring LTE cells with the largest number of times the LTE
cells are configured as the neighboring cells for different cells in
the active set until the number of the selected neighboring LTE
cells meets the specifications, filters out the excessive
neighboring LTE cells, and then selects the neighboring LTE
cells on the selected EARFCNS according to the principle of
preferentially selecting a maximum of four LTE FDD EARFCNs
and four LTE TDD EARFCNs. 18.
PERFENH_U2L_PUNISH_BASED_ABS_FREQ_SWITCH:
Whether a UE is allowed to perform a non-coverage-based
UMTS-to-LTE redirection after a redirection from UMTS to LTE
when

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH of
Loa the HoSwitch1 parameter in the SET UCORRMALGOSWITCH
d
command is turned on. When this switch is turned on, the UE is
not allowed to be redirected back to LTE. When this switch is
turned off, the UE is allowed to be redirected back to LTE. 19.
PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SWITCH:
Value of the HE bit IE during the RB reconfiguration. The HE bit
IE indicates whether the AMD PDU contains the length indicator
(LI). For details about this parameter, see 3GPP TS 25.321.
When this switch is turned on. During the RB reconfiguration,
the value of the HE bit IE for other operators' RNCs is
unchanged. When this switch is turned off. During the RB
reconfiguration, the HE bit IE for other operators' RNCs is
forcibly changed to the value of the HE bit IE for Huawei RNC,
which results in call drops. 20.
PERFENH_HHO_RELOC_OUT_WITH_MR_SWITCH:
Whether compatibility processing is performed on the
RELOCATION REQUIRED message during a combined hard
handover and SRNS relocation. When this switch is turned on.
Compatibility processing is performed so that the
RELOCATION REQUIRED carries the RSCP and Ec/N0
measurement results of the target cell. When this switch is turned
off. Compatibility processing is not performed so that the
RELOCATION REQUIRED does not carry the RSCP and Ec/N0
measurement results of the target cell. 21.
PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH:
Whether to initiate service-based UMTS-to-LTE handovers or
redirections after a P2D procedure is triggered for CS users.
After this switch is turned on, service-based UMTS-to-LTE
handovers or redirections are allowed, causing the CS service
establishment to fail. After the switch is turned off, service-based
UMTS-to-LTE handovers or redirections are not allowed. 22.
PERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH:
Whether to initiate service-based UMTS-to-LTE handovers or
redirections after RBs are reconfigured for a PS user. After this
switch is turned on, service-based UMTS-to-LTE handovers or
redirections are allowed after RBs are reconfigured for a PS user.
In this case, the user is always in the compressed mode if
"ChannelRetryHoTimerLen" is set to a value other than 0 in the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

"SET UCOIFTIMER" command and "HsdpaCMPermissionInd"


is set to FALSE, "HsupaCMPermissionInd" is set to Limited, or
"EHSPACMPermissionInd" is set to FALSE in the "SET
UCMCF" command. After this switch is turned off, servicebased UMTS-to-LTE handovers or redirections are forbidden
after RBs are reconfigured for a PS user. 23.
PERFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH:
Whether to check whether the UE requesting for service-based
UMTS-to-LTE handovers or redirections is an LTE UE or not.
After this switch is turned on, the RNC allows service-based
UMTS-to-LTE handovers or redirections for LTE UEs only.
When the switch is turned off, the RNC allows such handovers
or redirections for all requested UEs. 24.
PERFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH:
Method for the RNC to set the delay time for DTX/DRX to take
effect during the D2E channel switching procedure or the link
addition procedure of a soft handover for a UE enabled with the
DTX/DRX function. When this switch is turned on, For the D2E
channel switching procedure, the RNC sets the value of the
DtxDrxEnablingDelay parameter in the SET UFRC command to
the delay time for DTX/DRX to take effect. For the link addition
procedure of a soft handover, the RNC permanently sets the field
Enabling Delay in the RADIO LINK SETUP REQUEST
message to 0. When this switch is turned off, For the D2E
channel switching procedure, the RNC permanently sets the
delay time for DTX/DRX to take effect to 0. For the link
addition procedure of a soft handover, the RNC sets the field
Enabling Delay in the RADIO LINK SETUP REQUEST
message based on the value of the DtxDrxEnablingDelay
parameter in the SET UFRC command. 25.
PERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH:
Whether the RNC continues to apply a penalty to a UE that has
switched to the CELL_FACH, CELL_PCH, or URA_PCH state
after experiencing a measured-based DRD failure. When this
switch is turned on. The RNC continues to apply penalty to the
UE after the UE switches to the CELL_FACH, CELL_PCH, or
URA_PCH state from the CELL_DCH state. When this switch is
turned off. The RNC stops the penalty on the UE after the UE
switches to the CELL_FACH, CELL_PCH, or URA_PCH state

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

from the CELL_DCH state. 26.


PERFENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH:
Whether the RNC includes the new scheduling priority indicator
(SPI) weight adjustment factor in the Radio Link
Reconfiguration Prepare message when the SPI is changed
because the CN adjusts the traffic handle priority (THP) value
for an HSDPA service. When this switch is turned on. The RNC
includes the new SPI weight adjustment factor in the Radio Link
Reconfiguration Prepare message. When this switch is turned
off. The RNC does not include the new SPI weight adjustment
factor in the Radio Link Reconfiguration Prepare message.
GUI Value Range:
PERFENH_RCS_PS_DL_ON_DCH_SWITCH,
PERFENH_HSUPA_CAP_CHG_HRETRY_LMT_SWITCH,
PERFENH_MC_OPT_AFTER_RETRANS_CHG_SWITCH,
PERFENH_CSOVERH_H2D_RBID_CHG_SWITCH,
PERFENH_RRC_DRD_FAILED_RED_GSM_SWITCH,
PERFENH_IRAT_COV_HO_NCELL_PRE_SWITCH,
PERFENH_LTE_NCELL_SEL_OPT_SWITCH,
PERFENH_GSM_NCELL_SEL_OPT_SWITCH,
PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITCH,
PERFENH_ICMP_ACCELERATOR_OPT_SWITCH,
PERFENH_MULTI_PS_DCCC_SWITCH,
PERFENH_CHL_CHG_FAIL_MC_OLPC_OPT_SWITCH,
PERFENH_SET2MBR_ALLOW_D2F_SWITCH,
PERFENH_RAB_REL_WITH_PS_D2F_OPT_SWITCH,
PERFENH_DRNC_CU_WITHOUT_EXTCELL_SWITCH,
PERFENH_HO_NODEB_UP_RES_LIMIT_E2D_SWITCH,
PERFENH_LTE_NCELL_FILTE_OPT_SWITCH,
PERFENH_U2L_PUNISH_BASED_ABS_FREQ_SWITCH,
PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SWITCH,
PERFENH_HHO_RELOC_OUT_WITH_MR_SWITCH,
PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH,
PERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH,
PERFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH,
PERFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH,
PERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH,
PERFENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range:


PERFENH_RCS_PS_DL_ON_DCH_SWITCH,
PERFENH_HSUPA_CAP_CHG_HRETRY_LMT_SWITCH,
PERFENH_MC_OPT_AFTER_RETRANS_CHG_SWITCH,
PERFENH_CSOVERH_H2D_RBID_CHG_SWITCH,
PERFENH_RRC_DRD_FAILED_RED_GSM_SWITCH,
PERFENH_IRAT_COV_HO_NCELL_PRE_SWITCH,
PERFENH_LTE_NCELL_SEL_OPT_SWITCH,
PERFENH_GSM_NCELL_SEL_OPT_SWITCH,
PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITCH,
PERFENH_ICMP_ACCELERATOR_OPT_SWITCH,
PERFENH_MULTI_PS_DCCC_SWITCH,
PERFENH_CHL_CHG_FAIL_MC_OLPC_OPT_SWITCH,
PERFENH_SET2MBR_ALLOW_D2F_SWITCH,
PERFENH_RAB_REL_WITH_PS_D2F_OPT_SWITCH,
PERFENH_DRNC_CU_WITHOUT_EXTCELL_SWITCH,
PERFENH_HO_NODEB_UP_RES_LIMIT_E2D_SWITCH,
PERFENH_LTE_NCELL_FILTE_OPT_SWITCH,
PERFENH_U2L_PUNISH_BASED_ABS_FREQ_SWITCH,
PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SWITCH,
PERFENH_HHO_RELOC_OUT_WITH_MR_SWITCH,
PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH,
PERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH,
PERFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH,
PERFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH,
PERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH,
PERFENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH
Default Value:
PERFENH_RCS_PS_DL_ON_DCH_SWITCH:0,PERFENH_H
SUPA_CAP_CHG_HRETRY_LMT_SWITCH:0,PERFENH_M
C_OPT_AFTER_RETRANS_CHG_SWITCH:1,PERFENH_CS
OVERH_H2D_RBID_CHG_SWITCH:0,PERFENH_RRC_DR
D_FAILED_RED_GSM_SWITCH:1,PERFENH_IRAT_COV_
HO_NCELL_PRE_SWITCH:0,PERFENH_LTE_NCELL_SEL_
OPT_SWITCH:0,PERFENH_GSM_NCELL_SEL_OPT_SWIT
CH:0,PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITC
H:0,PERFENH_ICMP_ACCELERATOR_OPT_SWITCH:0,PE
RFENH_MULTI_PS_DCCC_SWITCH:0,PERFENH_CHL_CH
G_FAIL_MC_OLPC_OPT_SWITCH:1,PERFENH_SET2MBR

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

_ALLOW_D2F_SWITCH:1,PERFENH_RAB_REL_WITH_PS
_D2F_OPT_SWITCH:1,PERFENH_DRNC_CU_WITHOUT_E
XTCELL_SWITCH:1,PERFENH_HO_NODEB_UP_RES_LIM
IT_E2D_SWITCH:1,PERFENH_LTE_NCELL_FILTE_OPT_S
WITCH:1,PERFENH_U2L_PUNISH_BASED_ABS_FREQ_S
WITCH:0,PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SW
ITCH:1,PERFENH_HHO_RELOC_OUT_WITH_MR_SWITC
H:0,PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH:0,P
ERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH:0,PE
RFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH:0,PE
RFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH:1,P
ERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH:1,PERF
ENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH:0
PerfE
nhanc
eSwitc
h2

B
S
C
6
9
1
0

SET
UCO
RRM
PARA

W
RF
D02
11
01
W
RF
D01
06
14
03
W
RF
D02
02
03
W
RF
D02
03
03

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
HS
UP
A
2ms
TTI
Inte
r
RN
C
Soft
Han
dov

Meaning: 1. PERFENH_RCS_PS_DL_ON_DCH_SWITCH:
Whether the PS service in the RCS-e service is carried on the
DCH in the downlink. When this switch is turned off, the
channel bearer and downlink rate of the PS service in the RCS-e
service in the downlink are unlimited. When this switch is turned
on, the PS service in the RCS-e service can only be carried on
the DCH in the downlink and the downlink rate cannot exceed
the maximum downlink rate of the PS service in the RCS-e
service. For the maximum downlink rate of the PS service in the
RCS-e service, see "PsRcsDlDchRate" in the "SET UFRC"
command. 2.
PERFENH_HSUPA_CAP_CHG_HRETRY_LMT_SWITCH:
Whether the RNC prevents HSPA retry when the NodeB reports
that a cell does not support HSUPA due to high CPU load on the
DSP. This switch is turned off by default. OFF: This switch is
turned off. When the NodeB reports that the cell does not
support HSUPA services, the RNC does not trigger retry to the
HSPA channel in the following scenarios:The current cell
support the channel retry from the DCH to the E-DCH.The
current cell support channel retries from DCH to the E-DCH and
the HSDSCH. ON: This switch is turned on. When the NodeB
reports that the cell does not support HSUPA services, the RNC
does not trigger retry to the HSPA channel during the DCH to EDCH channel retry. 3.
PERFENH_MC_OPT_AFTER_RETRANS_CHG_SWITCH:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D14
02
18
W
RF
D15
02
17
W
RF
D02
04
00
W
RF
D02
05
03
W
RF
D02
06
05
W
RF
D15
02
20
W
RF

er
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Ser
vice
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
Loa
d
Bas
ed
PS
Han
dov
er
fro
m

Description

Policy used when the RNC receives a request for changing the
target number of retransmissions during an E-DCH-to-DCH
(E2D) channel migration. ON: This switch is turned on. Upon
receiving the request for changing the target number of
retransmissions, the RNC continues the channel migration
procedure and then updates measurement control. OFF: This
switch is turned off. Upon receiving the request for changing the
target number of retransmissions, the RNC instantly updates
measurement control and then performs the channel migration.
However, this increases the call drop rate. 4.
PERFENH_CSOVERH_H2D_RBID_CHG_SWITCH: Whether
the RNC changes the radio bearer identity when CS services are
handed over from E-DCHs or HS-DSCHs to DCHs. This switch
is turned off by default. When this switch is turned on, the RNC
changes the radio bearer identity. When this switch is turned off,
the RNC does not change the radio bearer identity. For details,
see section 8.6.4.2 in 3GPP TS 25.331 V8.4.0. 5.
PERFENH_RRC_DRD_FAILED_RED_GSM_SWITCH:
Whether the RNC carries the information about the configured
neighboring GSM cells in the RRC CONNECTION REJECT
message when neighboring GSM cells are configured during an
RRC inter-RAT redirection based on admission failures. For UEs
of 3GPP Release 6 or a later version, when this switch is turned
on, the RNC carries the information about the configured
neighboring GSM cells in the RRC CONNECTION REJECT
message. When this switch is turned off, the RNC does not carry
the information about the configured neighboring GSM cells in
the RRC CONNECTION REJECT message. 6.
PERFENH_IRAT_COV_HO_NCELL_PRE_SWITCH: Whether
high-priority neighboring cells or frequencies are preferred
during coverage-based inter-RAT handovers. When this switch is
turned on, high-priority neighboring cells or frequencies are
preferred. If neighboring cells or frequencies have the same
priority, those with better signal quality are preferred. If their
signal quality is the same, the first selected neighboring cell or
frequency is the target cell or frequency. For UMTS-to-GSM
handovers, the neighboring cell with a smaller value of the
"HOPrio" parameter in the "ADD U2GNCELL" command is
preferentially selected as the target cell. For UMTS-to-LTE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D01
06
10
W
RF
D02
04
00
03
W
RF
D01
06
12
W
RF
D01
06
12
03
W
RF
D02
01
34
W
RF
D01
06
19
W
RF

UM
TS
to
LTE
DR
D
Intr
odu
ctio
n
Pac
kag
e
Out
er
Loo
p
Po
wer
Con
trol
SR
NS
Rel
ocat
ion
Intr
odu
ctio
n
Pac
kag
e
Cov
erag
e
Bas
ed
PS

Description

redirections, the frequency with a greater value of the


"NPriority" parameter in the "ADD UCELLNFREQPRIOINFO"
command is preferentially selected as the target frequency. When
this switch is turned off, only signal quality is considered. For
UMTS-to-GSM handovers, the neighboring cell with better
signal quality is preferentially selected as the target cell. For
UMTS-to-LTE redirections, the frequency with better quality is
preferentially selected as the target frequency. 7.
PERFENH_LTE_NCELL_SEL_OPT_SWITCH: Whether to
optimize the list for measured neighboring LTE cells in the
measurement control message. When this switch is turned on, the
RNC filters out the list for measured neighboring LTE cells
according to the RNC-level parameters, cell capability, and UE
capabilities in handovers and redirections to the LTE network.
When this switch is turned off, the RNC does not filter out the
list for measured neighboring LTE cells. 8.
PERFENH_GSM_NCELL_SEL_OPT_SWITCH: Scope for
matching the neighboring cells in measurement reports during
handovers to GSM cells when there are multiple cells in the
active set and the HO_MC_NCELL_COMBINE_SWITCH
switch is turned on. In case of neighboring combination, when
this switch is turned on, the RNC matches the neighboring cells
in measurement reports with neighboring cells of all cells in the
current active set. When this switch is turned off, the RNC
matches the neighboring cells in measurement reports only with
the best cell's neighboring cells. 9.
PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITCH:
Whether to select the best target frequency during a frequencybased redirection from UMTS to LTE. When this switch is
turned on, the selected target frequency is used as the best
frequency if the measurement report contains multiple
neighboring cells that work at the same frequency. 10.
PERFENH_ICMP_ACCELERATOR_OPT_SWITCH : Switch
for the enhanced algorithm of accelerating the rate for
responding to control messages. This parameter is a professional
parameter and therefore you must configure this parameter under
the instruction of Huawei technical support.For RTT(round-trip
time) tests, the recommended value is ON. In other scenarios, the
recommended value is OFF. 11.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
01
29
W
RF
D01
06
09
02
W
RF
D02
14
00
W
RF
D02
03
06

Han
dov
er
fro
m
UM
TS
to
LTE
HS
DP
A
Intr
odu
ctio
n
Pac
kag
e
Inte
r
Syst
em
Red
irec
t
HS
UP
A
Intr
odu
ctio
n
Pac
kag
e
HS
UP
A

Description

PERFENH_MULTI_PS_DCCC_SWITCH: Whether to allocate


the RLC parameters corresponding to the 2 ms TTI to the
services that are not reconfigured during the reconfiguration
procedure and have a data rate higher than 2048 kbit/s. The 2048
kbit/s is the maximum data rate supported by the 10 ms TTI.
When this switch is turned on, the RNC allocates such services
the RLC parameters corresponding to the 2 ms TTI. When this
switch is turned off, the RNC does not allocate such services
these parameters. 12.
PERFENH_CHL_CHG_FAIL_MC_OLPC_OPT_SWITCH:
Whether to use invalid measurement control parameters and
power control parameters on the MAC-d entity again if a UE in
the CELL_DCH state fails to switch channels and then
experiences a channel fallback. When this switch is turned on,
the RNC uses these parameters again for such a UE. When this
switch is turned off, the RNC does not use these parameters
again for such a UE. 13.
PERFENH_SET2MBR_ALLOW_D2F_SWITCH: Whether to
allow CELL-DCH-to-CELL_FACH state transitions when the
PS BE services of a UE fail to be reconfigured with an MBR and
the UE periodically requests the MBR. When this switch is
turned on, the UE is allowed to perform CELL-DCH-toCELL_FACH state transitions in the preceding scenario. When
this switch is turned off, the UE is not allowed to perform these
state transitions. 14.
PERFENH_RAB_REL_WITH_PS_D2F_OPT_SWITCH:
Processing option for a low-rate PS service when the cell update
procedure overlaps the service release procedure of a CS or PS
service in combined services that also include the low-rate PS
service.When this switch is turned on, the parameter specifying
the status of the low-rate PS service is correctly configured in the
proceeding scenario to prevent a call drop.When this switch is
turned off, the previously mentioned parameter is incorrectly
configured in the proceeding scenario. This will result in a call
drop.For this parameter, please note the following: A low-rate PS
service is a service whose maximum data rate is less than the
values of the "UlBeTraffDecThs" and "DlBeTraffDecThs"
parameters. When a service in combined services that include a
low-rate PS service is being released, the UE is instructed to

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Po
wer
Con
trol
Pus
h to
Talk
CS
voic
e
ove
r
HS
PA/
HS
PA+
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to
LTE
Co
mbi
nati
on
of
One
CS
Ser
vice
and
One

Description

perform a state transition from CELL_DCH to CELL_FACH.


15. PERFENH_DRNC_CU_WITHOUT_EXTCELL_SWITCH:
This switch applies to the following two scenarios: Scenario 1: A
UE sends a CELL UPDATE message with a cause value of
"radio link failure" or "RLC unrecoverable error" in a drift RNC
(DRNC) cell that is not configured as a neighboring cell of the
UE's SRNC cell using the "ADD UEXT3GCELL" command.
This switch controls whether the serving RNC (SRNC)
reestablishes a radio link for the UE in this scenario. When this
switch is set to on, the SRNC uses the DSCR procedure to
reestablish a radio link for UEs processing PS BE only services;
the SRNC reestablishes a radio link for UEs processing services
other than PS BE only through the cell update procedure. When
this switch is set to off, the SRNC directly releases the RRC
connection of the UE. Scenario 2: A UE in the CELL_DCH state
sends a cell update request in a DRNC cell after the SRNC
triggers a call reestablishment. The DRNC cell has been
configured as a neighboring cell of the UE's SRNC cell using the
"ADD UEXT3GCELL" command, UE's services are carried
over HSPA channels in the DRNC cell but the SRNC is not
configured with the HSPA capability of the DRNC cell. This
switch controls whether the SRNC can correctly process the cell
update request in this scenario. When this switch is set to on, the
SRNC can correctly process the cell update request. When this
switch is set to off, the SRNC cannot correctly process the cell
update request and as a result, call drops occur. 16.
PERFENH_HO_NODEB_UP_RES_LIMIT_E2D_SWITCH:
Whether the RNC re-attempts to apply for DCH resources when
the NodeB sends to the RNC cause value not-enough-user-planeprocessing-resources during the request of E-DCH or HS-DSCH
resources for an intra-RAT handover. When this switch is turned
on, the RNC re-attempts to apply for the DCH resources in the
preceding scenario. When this switch is turned off, the RNC
stops applying for any channel resources. 17.
PERFENH_LTE_NCELL_FILTE_OPT_SWITCH: Whether the
RNC filters out neighboring LTE cells based on the principle of
preferentially selecting a maximum of four LTE FDD EARFCNs
and four LTE TDD EARFCNs when the following conditions are
met: 1. The active set contains more than one cell. 2. Each cell is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
PS
Ser
vice
Dir
ect
Sig
nali
ng
Con
nect
ion
Reesta
blis
hme
nt
(DS
CR)
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Description

configured with multiple neighboring LTE cells. 3.


HO_MC_NCELL_COMBINE_SWITCH of the "HoSwitch"
parameter in the "SET UCORRMALGOSWITCH" command
and HO_MC_LTE_NCELL_COMBINE_SWITCH of the
"HoSwitch1" parameter in the "SET UCORRMALGOSWITCH"
command are turned on. When this switch is turned on, the RNC
filters out the neighboring LTE cells based on the principle of
preferentially selecting a maximum of four LTE FDD EARFCNs
and four LTE TDD EARFCNs, preferentially selects the
neighboring LTE cells with the largest number of times the LTE
cells are configured as the neighboring cells for different cells in
the active set until the number of the selected neighboring LTE
cells meets the specifications, and then filters out the excessive
neighboring LTE cells to obtain the candidate neighboring cell
list. When this switch is turned off, the RNC selects the
neighboring LTE cells with the largest number of times the LTE
cells are configured as the neighboring cells for different cells in
the active set until the number of the selected neighboring LTE
cells meets the specifications, filters out the excessive
neighboring LTE cells, and then selects the neighboring LTE
cells on the selected EARFCNS according to the principle of
preferentially selecting a maximum of four LTE FDD EARFCNs
and four LTE TDD EARFCNs. 18.
PERFENH_U2L_PUNISH_BASED_ABS_FREQ_SWITCH:
Whether a UE is allowed to perform a non-coverage-based
UMTS-to-LTE redirection after a redirection from UMTS to LTE
when
HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH of
the HoSwitch1 parameter in the SET UCORRMALGOSWITCH
command is turned on. When this switch is turned on, the UE is
not allowed to be redirected back to LTE. When this switch is
turned off, the UE is allowed to be redirected back to LTE. 19.
PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SWITCH:
Value of the HE bit IE during the RB reconfiguration. The HE bit
IE indicates whether the AMD PDU contains the length indicator
(LI). For details about this parameter, see 3GPP TS 25.321.
When this switch is turned on. During the RB reconfiguration,
the value of the HE bit IE for other operators' RNCs is
unchanged. When this switch is turned off. During the RB

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

reconfiguration, the HE bit IE for other operators' RNCs is


forcibly changed to the value of the HE bit IE for Huawei RNC,
which results in call drops. 20.
PERFENH_HHO_RELOC_OUT_WITH_MR_SWITCH:
Whether compatibility processing is performed on the
RELOCATION REQUIRED message during a combined hard
handover and SRNS relocation. When this switch is turned on.
Compatibility processing is performed so that the
RELOCATION REQUIRED carries the RSCP and Ec/N0
measurement results of the target cell. When this switch is turned
off. Compatibility processing is not performed so that the
RELOCATION REQUIRED does not carry the RSCP and Ec/N0
measurement results of the target cell. 21.
PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH:
Whether to initiate service-based UMTS-to-LTE handovers or
redirections after a P2D procedure is triggered for CS users.
After this switch is turned on, service-based UMTS-to-LTE
handovers or redirections are allowed, causing the CS service
establishment to fail. After the switch is turned off, service-based
UMTS-to-LTE handovers or redirections are not allowed. 22.
PERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH:
Whether to initiate service-based UMTS-to-LTE handovers or
redirections after RBs are reconfigured for a PS user. After this
switch is turned on, service-based UMTS-to-LTE handovers or
redirections are allowed after RBs are reconfigured for a PS user.
In this case, the user is always in the compressed mode if
"ChannelRetryHoTimerLen" is set to a value other than 0 in the
"SET UCOIFTIMER" command and "HsdpaCMPermissionInd"
is set to FALSE, "HsupaCMPermissionInd" is set to Limited, or
"EHSPACMPermissionInd" is set to FALSE in the "SET
UCMCF" command. After this switch is turned off, servicebased UMTS-to-LTE handovers or redirections are forbidden
after RBs are reconfigured for a PS user. 23.
PERFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH:
Whether to check whether the UE requesting for service-based
UMTS-to-LTE handovers or redirections is an LTE UE or not.
After this switch is turned on, the RNC allows service-based
UMTS-to-LTE handovers or redirections for LTE UEs only.
When the switch is turned off, the RNC allows such handovers

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

or redirections for all requested UEs. 24.


PERFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH:
Method for the RNC to set the delay time for DTX/DRX to take
effect during the D2E channel switching procedure or the link
addition procedure of a soft handover for a UE enabled with the
DTX/DRX function. When this switch is turned on, For the D2E
channel switching procedure, the RNC sets the value of the
DtxDrxEnablingDelay parameter in the SET UFRC command to
the delay time for DTX/DRX to take effect. For the link addition
procedure of a soft handover, the RNC permanently sets the field
Enabling Delay in the RADIO LINK SETUP REQUEST
message to 0. When this switch is turned off, For the D2E
channel switching procedure, the RNC permanently sets the
delay time for DTX/DRX to take effect to 0. For the link
addition procedure of a soft handover, the RNC sets the field
Enabling Delay in the RADIO LINK SETUP REQUEST
message based on the value of the DtxDrxEnablingDelay
parameter in the SET UFRC command. 25.
PERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH:
Whether the RNC continues to apply a penalty to a UE that has
switched to the CELL_FACH, CELL_PCH, or URA_PCH state
after experiencing a measured-based DRD failure. When this
switch is turned on. The RNC continues to apply penalty to the
UE after the UE switches to the CELL_FACH, CELL_PCH, or
URA_PCH state from the CELL_DCH state. When this switch is
turned off. The RNC stops the penalty on the UE after the UE
switches to the CELL_FACH, CELL_PCH, or URA_PCH state
from the CELL_DCH state. 26.
PERFENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH:
Whether the RNC includes the new scheduling priority indicator
(SPI) weight adjustment factor in the Radio Link
Reconfiguration Prepare message when the SPI is changed
because the CN adjusts the traffic handle priority (THP) value
for an HSDPA service. When this switch is turned on. The RNC
includes the new SPI weight adjustment factor in the Radio Link
Reconfiguration Prepare message. When this switch is turned
off. The RNC does not include the new SPI weight adjustment
factor in the Radio Link Reconfiguration Prepare message.
GUI Value Range:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

PERFENH_RCS_PS_DL_ON_DCH_SWITCH,
PERFENH_HSUPA_CAP_CHG_HRETRY_LMT_SWITCH,
PERFENH_MC_OPT_AFTER_RETRANS_CHG_SWITCH,
PERFENH_CSOVERH_H2D_RBID_CHG_SWITCH,
PERFENH_RRC_DRD_FAILED_RED_GSM_SWITCH,
PERFENH_IRAT_COV_HO_NCELL_PRE_SWITCH,
PERFENH_LTE_NCELL_SEL_OPT_SWITCH,
PERFENH_GSM_NCELL_SEL_OPT_SWITCH,
PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITCH,
PERFENH_ICMP_ACCELERATOR_OPT_SWITCH,
PERFENH_MULTI_PS_DCCC_SWITCH,
PERFENH_CHL_CHG_FAIL_MC_OLPC_OPT_SWITCH,
PERFENH_SET2MBR_ALLOW_D2F_SWITCH,
PERFENH_RAB_REL_WITH_PS_D2F_OPT_SWITCH,
PERFENH_DRNC_CU_WITHOUT_EXTCELL_SWITCH,
PERFENH_HO_NODEB_UP_RES_LIMIT_E2D_SWITCH,
PERFENH_LTE_NCELL_FILTE_OPT_SWITCH,
PERFENH_U2L_PUNISH_BASED_ABS_FREQ_SWITCH,
PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SWITCH,
PERFENH_HHO_RELOC_OUT_WITH_MR_SWITCH,
PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH,
PERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH,
PERFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH,
PERFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH,
PERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH,
PERFENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH
Unit: None
Actual Value Range:
PERFENH_RCS_PS_DL_ON_DCH_SWITCH,
PERFENH_HSUPA_CAP_CHG_HRETRY_LMT_SWITCH,
PERFENH_MC_OPT_AFTER_RETRANS_CHG_SWITCH,
PERFENH_CSOVERH_H2D_RBID_CHG_SWITCH,
PERFENH_RRC_DRD_FAILED_RED_GSM_SWITCH,
PERFENH_IRAT_COV_HO_NCELL_PRE_SWITCH,
PERFENH_LTE_NCELL_SEL_OPT_SWITCH,
PERFENH_GSM_NCELL_SEL_OPT_SWITCH,
PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITCH,
PERFENH_ICMP_ACCELERATOR_OPT_SWITCH,
PERFENH_MULTI_PS_DCCC_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

PERFENH_CHL_CHG_FAIL_MC_OLPC_OPT_SWITCH,
PERFENH_SET2MBR_ALLOW_D2F_SWITCH,
PERFENH_RAB_REL_WITH_PS_D2F_OPT_SWITCH,
PERFENH_DRNC_CU_WITHOUT_EXTCELL_SWITCH,
PERFENH_HO_NODEB_UP_RES_LIMIT_E2D_SWITCH,
PERFENH_LTE_NCELL_FILTE_OPT_SWITCH,
PERFENH_U2L_PUNISH_BASED_ABS_FREQ_SWITCH,
PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SWITCH,
PERFENH_HHO_RELOC_OUT_WITH_MR_SWITCH,
PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH,
PERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH,
PERFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH,
PERFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH,
PERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH,
PERFENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH
Default Value:
PERFENH_RCS_PS_DL_ON_DCH_SWITCH:0,PERFENH_H
SUPA_CAP_CHG_HRETRY_LMT_SWITCH:0,PERFENH_M
C_OPT_AFTER_RETRANS_CHG_SWITCH:1,PERFENH_CS
OVERH_H2D_RBID_CHG_SWITCH:0,PERFENH_RRC_DR
D_FAILED_RED_GSM_SWITCH:1,PERFENH_IRAT_COV_
HO_NCELL_PRE_SWITCH:0,PERFENH_LTE_NCELL_SEL_
OPT_SWITCH:0,PERFENH_GSM_NCELL_SEL_OPT_SWIT
CH:0,PERFENH_U2L_REDIR_BASED_FREQ_OPT_SWITC
H:0,PERFENH_ICMP_ACCELERATOR_OPT_SWITCH:0,PE
RFENH_MULTI_PS_DCCC_SWITCH:0,PERFENH_CHL_CH
G_FAIL_MC_OLPC_OPT_SWITCH:1,PERFENH_SET2MBR
_ALLOW_D2F_SWITCH:1,PERFENH_RAB_REL_WITH_PS
_D2F_OPT_SWITCH:1,PERFENH_DRNC_CU_WITHOUT_E
XTCELL_SWITCH:1,PERFENH_HO_NODEB_UP_RES_LIM
IT_E2D_SWITCH:1,PERFENH_LTE_NCELL_FILTE_OPT_S
WITCH:1,PERFENH_U2L_PUNISH_BASED_ABS_FREQ_S
WITCH:0,PERFENH_HE_BIT_OPT_AFTER_RELOC_IN_SW
ITCH:1,PERFENH_HHO_RELOC_OUT_WITH_MR_SWITC
H:0,PERFENH_CS_P2D_TRIG_SERVICE_U2L_SWITCH:0,P
ERFENH_RB_RECFG_TRIG_SERVICE_U2L_SWITCH:0,PE
RFENH_PERMIT_U2L_ONLY_UE_FROM_L_SWITCH:0,PE
RFENH_DTXDRX_ENABLEDELAY_CFGOPT_SWITCH:1,P
ERFENH_MCDRD_FAIL_PENALTY_OPT_SWITCH:1,PERF

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ENH_HSDPA_SPI_WEIGHT_UPDATE_SWITCH:0
RsvS B SET No Non
witch1 S UAL ne e
C GOR
6 SVPA
9 RA
0
0

Meaning: RRM algorithm reserved U32 Switch Para 1. The 32bit parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_1_BIT1,
RESERVED_SWITCH_1_BIT2,
RESERVED_SWITCH_1_BIT3,
RESERVED_SWITCH_1_BIT4,
RESERVED_SWITCH_1_BIT5,
RESERVED_SWITCH_1_BIT6,
RESERVED_SWITCH_1_BIT7,
RESERVED_SWITCH_1_BIT8,
RESERVED_SWITCH_1_BIT9,
RESERVED_SWITCH_1_BIT10,
RESERVED_SWITCH_1_BIT11,
RESERVED_SWITCH_1_BIT12,
RESERVED_SWITCH_1_BIT13,
RESERVED_SWITCH_1_BIT14,
RESERVED_SWITCH_1_BIT15,
RESERVED_SWITCH_1_BIT16,
RESERVED_SWITCH_1_BIT17,
RESERVED_SWITCH_1_BIT18,
RESERVED_SWITCH_1_BIT19,
RESERVED_SWITCH_1_BIT20,
RESERVED_SWITCH_1_BIT21,
RESERVED_SWITCH_1_BIT22,
RESERVED_SWITCH_1_BIT23,
RESERVED_SWITCH_1_BIT24,
RESERVED_SWITCH_1_BIT25,
RESERVED_SWITCH_1_BIT26,
RESERVED_SWITCH_1_BIT27,
RESERVED_SWITCH_1_BIT28,
RESERVED_SWITCH_1_BIT29,
RESERVED_SWITCH_1_BIT30,
RESERVED_SWITCH_1_BIT31,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_1_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_1_BIT1,
RESERVED_SWITCH_1_BIT2,
RESERVED_SWITCH_1_BIT3,
RESERVED_SWITCH_1_BIT4,
RESERVED_SWITCH_1_BIT5,
RESERVED_SWITCH_1_BIT6,
RESERVED_SWITCH_1_BIT7,
RESERVED_SWITCH_1_BIT8,
RESERVED_SWITCH_1_BIT9,
RESERVED_SWITCH_1_BIT10,
RESERVED_SWITCH_1_BIT11,
RESERVED_SWITCH_1_BIT12,
RESERVED_SWITCH_1_BIT13,
RESERVED_SWITCH_1_BIT14,
RESERVED_SWITCH_1_BIT15,
RESERVED_SWITCH_1_BIT16,
RESERVED_SWITCH_1_BIT17,
RESERVED_SWITCH_1_BIT18,
RESERVED_SWITCH_1_BIT19,
RESERVED_SWITCH_1_BIT20,
RESERVED_SWITCH_1_BIT21,
RESERVED_SWITCH_1_BIT22,
RESERVED_SWITCH_1_BIT23,
RESERVED_SWITCH_1_BIT24,
RESERVED_SWITCH_1_BIT25,
RESERVED_SWITCH_1_BIT26,
RESERVED_SWITCH_1_BIT27,
RESERVED_SWITCH_1_BIT28,
RESERVED_SWITCH_1_BIT29,
RESERVED_SWITCH_1_BIT30,
RESERVED_SWITCH_1_BIT31,
RESERVED_SWITCH_1_BIT32
Default Value:
RESERVED_SWITCH_1_BIT1:0,RESERVED_SWITCH_1_BI
T2:0,RESERVED_SWITCH_1_BIT3:0,RESERVED_SWITCH_
1_BIT4:0,RESERVED_SWITCH_1_BIT5:0,RESERVED_SWI
TCH_1_BIT6:0,RESERVED_SWITCH_1_BIT7:0,RESERVED

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

_SWITCH_1_BIT8:0,RESERVED_SWITCH_1_BIT9:0,RESER
VED_SWITCH_1_BIT10:0,RESERVED_SWITCH_1_BIT11:0,
RESERVED_SWITCH_1_BIT12:0,RESERVED_SWITCH_1_B
IT13:0,RESERVED_SWITCH_1_BIT14:0,RESERVED_SWIT
CH_1_BIT15:0,RESERVED_SWITCH_1_BIT16:0,RESERVED
_SWITCH_1_BIT17:0,RESERVED_SWITCH_1_BIT18:0,RES
ERVED_SWITCH_1_BIT19:0,RESERVED_SWITCH_1_BIT2
0:0,RESERVED_SWITCH_1_BIT21:0,RESERVED_SWITCH_
1_BIT22:0,RESERVED_SWITCH_1_BIT23:0,RESERVED_S
WITCH_1_BIT24:0,RESERVED_SWITCH_1_BIT25:0,RESER
VED_SWITCH_1_BIT26:0,RESERVED_SWITCH_1_BIT27:0,
RESERVED_SWITCH_1_BIT28:0,RESERVED_SWITCH_1_B
IT29:0,RESERVED_SWITCH_1_BIT30:0,RESERVED_SWIT
CH_1_BIT31:0,RESERVED_SWITCH_1_BIT32:0
RsvS B SET No Non
witch1 S UAL ne e
C GOR
6 SVPA
9 RA
1
0

Meaning: RRM algorithm reserved U32 Switch Para 1. The 32bit parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_1_BIT1,
RESERVED_SWITCH_1_BIT2,
RESERVED_SWITCH_1_BIT3,
RESERVED_SWITCH_1_BIT4,
RESERVED_SWITCH_1_BIT5,
RESERVED_SWITCH_1_BIT6,
RESERVED_SWITCH_1_BIT7,
RESERVED_SWITCH_1_BIT8,
RESERVED_SWITCH_1_BIT9,
RESERVED_SWITCH_1_BIT10,
RESERVED_SWITCH_1_BIT11,
RESERVED_SWITCH_1_BIT12,
RESERVED_SWITCH_1_BIT13,
RESERVED_SWITCH_1_BIT14,
RESERVED_SWITCH_1_BIT15,
RESERVED_SWITCH_1_BIT16,
RESERVED_SWITCH_1_BIT17,
RESERVED_SWITCH_1_BIT18,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_1_BIT19,
RESERVED_SWITCH_1_BIT20,
RESERVED_SWITCH_1_BIT21,
RESERVED_SWITCH_1_BIT22,
RESERVED_SWITCH_1_BIT23,
RESERVED_SWITCH_1_BIT24,
RESERVED_SWITCH_1_BIT25,
RESERVED_SWITCH_1_BIT26,
RESERVED_SWITCH_1_BIT27,
RESERVED_SWITCH_1_BIT28,
RESERVED_SWITCH_1_BIT29,
RESERVED_SWITCH_1_BIT30,
RESERVED_SWITCH_1_BIT31,
RESERVED_SWITCH_1_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_1_BIT1,
RESERVED_SWITCH_1_BIT2,
RESERVED_SWITCH_1_BIT3,
RESERVED_SWITCH_1_BIT4,
RESERVED_SWITCH_1_BIT5,
RESERVED_SWITCH_1_BIT6,
RESERVED_SWITCH_1_BIT7,
RESERVED_SWITCH_1_BIT8,
RESERVED_SWITCH_1_BIT9,
RESERVED_SWITCH_1_BIT10,
RESERVED_SWITCH_1_BIT11,
RESERVED_SWITCH_1_BIT12,
RESERVED_SWITCH_1_BIT13,
RESERVED_SWITCH_1_BIT14,
RESERVED_SWITCH_1_BIT15,
RESERVED_SWITCH_1_BIT16,
RESERVED_SWITCH_1_BIT17,
RESERVED_SWITCH_1_BIT18,
RESERVED_SWITCH_1_BIT19,
RESERVED_SWITCH_1_BIT20,
RESERVED_SWITCH_1_BIT21,
RESERVED_SWITCH_1_BIT22,
RESERVED_SWITCH_1_BIT23,
RESERVED_SWITCH_1_BIT24,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_1_BIT25,
RESERVED_SWITCH_1_BIT26,
RESERVED_SWITCH_1_BIT27,
RESERVED_SWITCH_1_BIT28,
RESERVED_SWITCH_1_BIT29,
RESERVED_SWITCH_1_BIT30,
RESERVED_SWITCH_1_BIT31,
RESERVED_SWITCH_1_BIT32
Default Value:
RESERVED_SWITCH_1_BIT1:0,RESERVED_SWITCH_1_BI
T2:0,RESERVED_SWITCH_1_BIT3:0,RESERVED_SWITCH_
1_BIT4:0,RESERVED_SWITCH_1_BIT5:0,RESERVED_SWI
TCH_1_BIT6:0,RESERVED_SWITCH_1_BIT7:0,RESERVED
_SWITCH_1_BIT8:0,RESERVED_SWITCH_1_BIT9:0,RESER
VED_SWITCH_1_BIT10:0,RESERVED_SWITCH_1_BIT11:0,
RESERVED_SWITCH_1_BIT12:0,RESERVED_SWITCH_1_B
IT13:0,RESERVED_SWITCH_1_BIT14:0,RESERVED_SWIT
CH_1_BIT15:0,RESERVED_SWITCH_1_BIT16:0,RESERVED
_SWITCH_1_BIT17:0,RESERVED_SWITCH_1_BIT18:0,RES
ERVED_SWITCH_1_BIT19:0,RESERVED_SWITCH_1_BIT2
0:0,RESERVED_SWITCH_1_BIT21:0,RESERVED_SWITCH_
1_BIT22:0,RESERVED_SWITCH_1_BIT23:0,RESERVED_S
WITCH_1_BIT24:0,RESERVED_SWITCH_1_BIT25:0,RESER
VED_SWITCH_1_BIT26:0,RESERVED_SWITCH_1_BIT27:0,
RESERVED_SWITCH_1_BIT28:0,RESERVED_SWITCH_1_B
IT29:0,RESERVED_SWITCH_1_BIT30:0,RESERVED_SWIT
CH_1_BIT31:0,RESERVED_SWITCH_1_BIT32:0
InterR
atPhy
ChFail
Num

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR

W
RF
D02
03
03
W
RF
D02
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov

Meaning: Maximum number of inter-RAT handover failures


allowed due to physical channel failure. When the number of
inter-RAT handover failures due to physical channel failure
exceeds the threshold, a penalty is given to the UE. During the
time specified by "PenaltyTimeForInterRatPhyChFail", the UE
is not allowed to make inter-RAT handover attempts. For details
about the physical channel failure, see 3GPP TS 25.331.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~63

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

InterR
atPhy
ChFail
Num

B
S
C
6
9
1
0

Description

ATH
OCO
V

05
W
RF
D02
03
06

erag Default Value: 3


e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH

W
RF
D02
03
03
W
RF
D02
03
05

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag

Meaning: Maximum number of inter-RAT handover failures


allowed due to physical channel failure. When the number of
inter-RAT handover failures due to physical channel failure
exceeds the threshold, a penalty is given to the UE. During the
time specified by "PenaltyTimeForInterRatPhyChFail", the UE
is not allowed to make inter-RAT handover attempts. For details
about the physical channel failure, see 3GPP TS 25.331.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~63
Default Value: 3

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Penalt
yTime
ForPh
yChFa
il

B
S
C
6
9
0
0

OCO
V

W
RF
D02
03
06

e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO

W
RF
D02
03
05
W
RF
D02
03
06
W

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice

Description

Meaning: Length of a penalty timer for inter-RAT handover


failures due to physical channel failures. During the period
specified by "PenaltyTimeForPhyChFail", the UE is not allowed
to make inter-RAT handover attempts. For details about the
physical channel failure, see 3GPP TS 25.331.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 30

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
V

RF
D02
03
03

Description

Penalt
yTime
ForPh
yChFa
il

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice

Meaning: Length of a penalty timer for inter-RAT handover


failures due to physical channel failures. During the period
specified by "PenaltyTimeForPhyChFail", the UE is not allowed
to make inter-RAT handover attempts. For details about the
physical channel failure, see 3GPP TS 25.331.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 30

PerfE
nhanc
eSwitc
h

B
S
C
6
9
0
0

SET
UCO
RRM
PARA

W
RF
D01
06
10
04
W
RF
D02
11
04
W

HS
DP
A
Po
wer
Con
trol
Em
erge
ncy
Call
HS
UP
A

Meaning: 1. PERFENH_AMR_SPEC_BR_SWITCH: When this


switch is turned on, the procedure specific to AMR service
establishment takes effect. 2.
PERFENH_AMR_TMPLT_SWITCH: When this switch is
turned on, the AMR template takes effect. 3.
PERFENH_SRB_TMPLT_SWITCH: When this switch is turned
on, the SRB template takes effect. 4.
PERFENH_OLPC_TMPLT_SWITCH: When this switch is
turned on, the OLPC template takes effect. 5.
PERFENH_AMR_SP_TMPLT_SWITCH: When this switch is
turned on, the AMR parameter template takes effect. 6.
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH: When this
switch is turned on, the intra-frequency measurement control
template takes effect. 7.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D01
06
14
04
W
RF
D14
01
02
W
RF
D02
06
05
01
W
RF
D01
02
02
W
RF
D02
04
00
03
W
RF
D02
04
02

2ms
/10
ms
TTI
Han
dov
er
CS
Fall
bac
k
Gua
rant
ee
for
LTE
Em
erge
ncy
Call
s
SR
NS
Rel
ocat
ion
(UE
Not
Inv
olve
d)
UE
Stat
e in
Con
nect
ed
Mo
de

Description

PERFENH_INTERRAT_PENALTY_50_SWITCH: After a UE
fails to be handed over to a 2G cell during an inter-RAT
handover, the RNC forbids the UE to attempt a handover to the
2G cell in a certain period. When this switch is turned on, the
period is 50s. When this switch is turned off, the period is 30s. 8.
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH: When this
switch is turned on, the uplink SRBs of HSUPA 10 ms nonconversational services are always carried on DCHs, and the
original parameter Type of Channel Preferably Carrying
Signaling RB is invalid. When this switch is turned off, SRBs for
HSUPA 10 ms non-conversational services can be carried on
HSUPA channels when the original parameter Type of Channel
Preferably Carrying Signaling RB is set to HSUPA or HSPA. The
switch is set to OFF by default. 9.
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH: When this
switch is turned on, the single-user peak-rate improvement
algorithm of HSUPA 2 ms TTI is enabled. When this switch is
turned off, the algorithm is disabled. The switch is set to OFF by
default. 10. PERFENH_UU_P2D_CUC_OPT_SWITCH: When
this switch is turned on, the P2D cell update confirm message
simplification algorithm takes effect. When this switch is turned
off, the algorithm does not take effect. By default, this switch is
turned off. 11.
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH: This
check box controls whether the RNC considers the converged
SIRTarget value that is used before radio link reconfiguration in
outer loop power control performed after radio link
reconfiguration. If the check box is not selected, the RNC sends
the initial SIRTarget value used after radio link reconfiguration
to the NodeB.If the check box is selected, the RNC selects a
more appropriate value from the initial SIRTarget value used
after radio link reconfiguration and the converged SIRTarget
value used before radio link reconfiguration. Then the RNC
sends the selected value to the NodeB. Setting of this check box
takes effect only when the
PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH check box
is selected. 12. PERFENH_RRC_REDIR_PROTECT_SWITCH:
When this switch is turned on, The mechanism to avoid endless
back-and-forth RRC-redirections takes effect. The switch is set

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D02
04
00
W
RF
D01
06
36

(CE
LLDC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
Inte
r
Syst
em
Red
irec
t
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
DR
D
Intr
odu
ctio
n

Description

to OFF by default. 13. PERFENH_H2F_OPT_SWITCH:


whether to enable the optimized algorithm for HSPA UE state
transition from CELL_DCH to CELL_FACH (also referred to as
H2F state transition). When the switch is turned on, the
optimized H2F state transition algorithm is enabled, and event
4A measurement of traffic volume or throughput is added to the
state transition procedure. The added event 4A measurement
prevents an H2F state transition when data is being transmitted.
14. PERFENH_PSTRAFFIC_P2H_SWITCH: When the switch
is turned on and a CELL_PCH/URA_PCH-to-CELL_DCH (P2D
for short) state transition is triggered for a PS service, the PS
service can be set up on HSPA channels after the state transition.
When the switch is turned off, PS services can be set up only on
DCHs after a P2D state transition. This switch is turned off by
default. 15. PERFENH_VIP_USER_PCHR_MR_SWITCH:
When this switch is turned on, VIP UEs report their transmit
power to the RNC when required and periodically measure
signal quality of intra-frequency cells. In addition, these UEs
measure the downlink BLER, the NodeB measures the uplink
SIR, and the RNC records the measurement results. 16.
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH: Switch
for including the Tx interruption after trigger IE in the uplink 4A
traffic volume measurement control message. When this switch
is turned on, the uplink 4A traffic volume measurement control
message from RNC includes the Tx interruption after trigger IE
for UEs that are in the CELL_FACH or enhanced CELL_FACH
state and processing PS BE services. The value of this IE can be
changed by running the "SET UUESTATETRANS" command.
17.
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH:
The NodeB baseband board uses different processing
specifications for users with different uplink bearer services, for
example, HSUPA TTI 2 ms services, HSUPA TTI 10 ms
services, and R99 services. When serving a large number of
users, the system cannot guarantee that all users can access the
network with the highest service bearer supported by UEs. This
switch controls whether the RNC allocates corresponding
channels for new users based on the cell capability reported
through the NodeB private interface. When this switch is turned

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Pac
kag
e
SR
B
ove
r
HS
UP
A

Description

on, the RNC dynamically selects an appropriate uplink service


bearer and allocates corresponding channels for new users to
maximize the system capacity based on the actual NodeB
processing specifications. When this switch is turned off, the
optimization process is disabled. 18.
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH:
Whether to use the optimized TTI switching algorithm for BE
services When this switch is turned off, the optimized algorithm
does not take effect. The original mechanism is implemented.
When this switch is turned on, the optimized algorithm takes
effect. After HSUPA services are configured or reconfigured
with 10 ms TTI due to network resource (admission CEs, RTWP,
consumed Iub bandwidth, or consumed CEs) congestion or
insufficient coverage, these UEs cannot change to use 2 ms TTI
if no data needs to be transmitted. 19.
PERFENH_DOWNLOAD_ENHANCE_SWITCH: Whether to
activate the algorithm for increasing the single-threaded
download rate. 20. PERFENH_OLPC_BLER_COEF_ADJUST:
Switch for adjusting the BLER coefficient specific to CS
services based on the best cell's uplink load status. When this
switch is turned on, the outer loop power control algorithm uses
the target BLER set by the OMU board if the best cell's uplink
load status is LDR or OLC. If the status is neither LDR nor
OLC, this algorithm uses this target BLER after being divided by
five. 21. PERFENH_EMG_AGPS_MC_DELAY_SWITCH:
Whether to enable the function of delaying the sending of an
RRC_MEAS_CTRL message containing AGPS information
when an emergency call is made. When this switch is turned on,
the RNC delays the sending of this message until the emergency
call is successfully set up. When this switch is turned off, the
RNC sends this message upon receiving a
LOCATION_REPORTING_CONTROL message from the CN.
22. PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITCH:
Whether to enable a UE having multiple RLSs to use the value
of "CQIReF" and the value of "CQIFbCk" that are for UEs
having only one RLS. The two parameters can be set by running
the "SET UHSDPCCH" and "ADD UCELLHSDPCCH"
commands. When this switch is turned off, the UE does not use
the values of the two parameters that are for UEs having only

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

one RLS. When this switch is turned on, the UE uses the values
of the two parameters that are for UEs having only one RLS. 23.
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWITCH:
Whether to enable a RELOCATION REQUIRED message to
contain the IE calculationTimeForCiphering. When this switch is
turned on, static relocation request messages contain the IE
calculationTimeForCiphering. 24.
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH: Whether to
trigger the DRD procedure and channel switchover from E-DCH
or HS-DSCH to DCH when messages transmitted over the Uu
and Iub interfaces do not arrive in time. When this switch is
turned off, the DRD procedure and channel switchover from EDCH or HS-DSCH to DCH are not triggered if messages
transmitted over the Uu and Iub interfaces do not arrive in time.
When this switch is turned on, the DRD procedure and channel
switchover from E-DCH or HS-DSCH to DCH are triggered if
messages transmitted over the Uu and Iub interfaces do not
arrive in time. 25.
PERFENH_CELL_CACLOAD_BROADCAST_AMEND:
Whether to consider CE or code resource usage when
determining the resource status of a cell whose serving boards or
CP sub-systems are different from those of its neighboring cells.
When this switch is turned on, the RNC determines the resource
status of such a cell based on power, CE, and code resource
usage. If power, CE, or code resources in a cell become
congested, the RNC determines that the cell experiences
resource congestion. When this switch is turned off, the RNC
determines the resource status of such a cell based on power
resource usage only. 26.
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH: When this
switch is turned on, candidate cells are ranked by
"InterFreqMeasQuantity" (in the "ADD
UCELLMBDRINTERFREQ" command) for MBDR, and the
cell with the best signal quality is selected as the target cell.
When this switch is turned off, candidate cells are not ranked by
InterFreqMeasQuantity for MBDR. 27.
PERFENH_RRC_DRD_PREADMISSION_SWITCH: Whether
the RNC makes a pre-admission decision on intra-RAT DRDs or
redirections during an RRC connection setup. When this switch

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

is turned on, the RNC makes a pre-admission decision on intraRAT DRDs or redirections during an RRC connection setup.
When this switch is turned off, the RNC does not make a preadmission decision on intra-RAT DRDs or redirections during an
RRC connection setup. 28.
PERFENH_RRC_WEAK_REDIR_SWITCH: Whether to
activate the RRC redirection in weak coverage algorithm. When
this switch is turned on, UEs located in weak coverage are
redirected to the neighboring GSM cell through RRC redirection.
When this switch is turned off, this algorithm is disabled. 29.
PERFENH_L2U_CSFB_COMMCALL_SWITCH: Whether to
preferentially admit PS services of UEs involved in LTE-toUMTS CS fallback. When this switch is turned on: If a UE
involved in a LTE-to-UMTS CS fallback is processing a nonreal-time PS service, the channel type and initial data rate for the
PS service are determined by the "NRTInitRateforL2U"
parameter in the "SET UFRC" command during service
admission. If the UE is processing a real-time PS service, the UE
follows the standard access procedure. If the access attempt fails
and the "PreemptAlgoSwitch" in the "SET
UQUEUEPREEMPT" command is turned on, the UE can
preempt radio resources of existing UEs in the UMTS cell. When
this switch is turned off, the UE follows the standard access
procedure for the PS service. 30.
PERFENH_DLBLINDDETECT_WHEN_ONLYSRBONDCH:
This parameter controls whether to enable blind detection for the
HSDPA user-associated single-signaling R99 channel. When the
switch specified by this parameter is turned on, blind detection is
enabled. 31.
PERFENH_DLBLINDDETECT_WHEN_SRBAMRONDCH:
This parameter controls whether to enable blind detection for the
HSDPA user-associated AMR R99 channel. When the switch
specified by this parameter is turned on, blind detection is
enabled if the HSDPA service has been set up and there are
signaling and AMR traffic carried on the R99 channel. 32.
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT: Whether
to allow R6 UEs to switch from HSUPA 10 ms to 2 ms TTI.
When the switch is turned on, this switching is not allowed for
R6 UEs. When the switch is turned off, this limit does not work.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

This parameter is an advanced parameter. To modify this


parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,
PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH,
PERFENH_RRC_REDIR_PROTECT_SWITCH,
PERFENH_H2F_OPT_SWITCH,
PERFENH_PSTRAFFIC_P2H_SWITCH,
PERFENH_VIP_USER_PCHR_MR_SWITCH,
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH,
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH,
PERFENH_DOWNLOAD_ENHANCE_SWITCH,
PERFENH_OLPC_BLER_COEF_ADJUST,
PERFENH_EMG_AGPS_MC_DELAY_SWITCH,
PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITCH,
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWITCH,
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH,
PERFENH_CELL_CACLOAD_BROADCAST_AMEND,
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH,
PERFENH_RRC_DRD_PREADMISSION_SWITCH,
PERFENH_RRC_WEAK_REDIR_SWITCH,
PERFENH_L2U_CSFB_COMMCALL_SWITCH,
PERFENH_DLBLINDDETECT_WHEN_ONLYSRBONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAMRONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Unit: None
Actual Value Range: PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH,
PERFENH_RRC_REDIR_PROTECT_SWITCH,
PERFENH_H2F_OPT_SWITCH,
PERFENH_PSTRAFFIC_P2H_SWITCH,
PERFENH_VIP_USER_PCHR_MR_SWITCH,
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH,
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH,
PERFENH_DOWNLOAD_ENHANCE_SWITCH,
PERFENH_OLPC_BLER_COEF_ADJUST,
PERFENH_EMG_AGPS_MC_DELAY_SWITCH,
PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITCH,
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWITCH,
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH,
PERFENH_CELL_CACLOAD_BROADCAST_AMEND,
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH,
PERFENH_RRC_DRD_PREADMISSION_SWITCH,
PERFENH_RRC_WEAK_REDIR_SWITCH,
PERFENH_L2U_CSFB_COMMCALL_SWITCH,
PERFENH_DLBLINDDETECT_WHEN_ONLYSRBONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAMRONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Default Value:
PERFENH_AMR_SPEC_BR_SWITCH:1,PERFENH_AMR_T
MPLT_SWITCH:1,PERFENH_SRB_TMPLT_SWITCH:1,PER
FENH_OLPC_TMPLT_SWITCH:1,PERFENH_AMR_SP_TMP
LT_SWITCH:1,PERFENH_INTRAFREQ_MC_TMPLT_SWIT
CH:1,PERFENH_INTERRAT_PENALTY_50_SWITCH:1,PER
FENH_SRB_OVER_HSUPA_TTI10_SWITCH:0,PERFENH_H
SUPA_TTI2_ENHANCE_SWITCH:0,PERFENH_UU_P2D_C
UC_OPT_SWITCH:0,PERFENH_RL_RECFG_SIR_CONSIDE
R_SWITCH:1,PERFENH_RRC_REDIR_PROTECT_SWITCH:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

0,PERFENH_H2F_OPT_SWITCH:0,PERFENH_PSTRAFFIC_
P2H_SWITCH:0,PERFENH_VIP_USER_PCHR_MR_SWITC
H:0,PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH:0,PE
RFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH:0,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH:0,PE
RFENH_DOWNLOAD_ENHANCE_SWITCH:0,PERFENH_O
LPC_BLER_COEF_ADJUST:1,PERFENH_EMG_AGPS_MC_
DELAY_SWITCH:0,PERFENH_MULTI_RLS_CQI_PARA_OP
T_SWITCH:0,PERFENH_RELOC_IE_CALCTIMEFORCIP_S
WITCH:0,PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH:0,
PERFENH_CELL_CACLOAD_BROADCAST_AMEND:1,PE
RFENH_MBDR_TARCELLSEL_OPT_SWITCH:0,PERFENH_
RRC_DRD_PREADMISSION_SWITCH:0,PERFENH_RRC_
WEAK_REDIR_SWITCH:0,PERFENH_L2U_CSFB_COMMC
ALL_SWITCH:0,PERFENH_DLBLINDDETECT_WHEN_ON
LYSRBONDCH:0,PERFENH_DLBLINDDETECT_WHEN_SR
BAMRONDCH:0,PERFENH_R6_HSUPA_TTI_10MSTO2MS_
LIMIT:0
PerfE
nhanc
eSwitc
h

B
S
C
6
9
1
0

SET
UCO
RRM
PARA

W
RF
D01
06
10
04
W
RF
D02
11
04
W
RF
D01
06
14
04

HS
DP
A
Po
wer
Con
trol
Em
erge
ncy
Call
HS
UP
A
2ms
/10
ms
TTI
Han
dov

Meaning: 1. PERFENH_AMR_SPEC_BR_SWITCH: When this


switch is turned on, the procedure specific to AMR service
establishment takes effect. 2.
PERFENH_AMR_TMPLT_SWITCH: When this switch is
turned on, the AMR template takes effect. 3.
PERFENH_SRB_TMPLT_SWITCH: When this switch is turned
on, the SRB template takes effect. 4.
PERFENH_OLPC_TMPLT_SWITCH: When this switch is
turned on, the OLPC template takes effect. 5.
PERFENH_AMR_SP_TMPLT_SWITCH: When this switch is
turned on, the AMR parameter template takes effect. 6.
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH: When this
switch is turned on, the intra-frequency measurement control
template takes effect. 7.
PERFENH_INTERRAT_PENALTY_50_SWITCH: After a UE
fails to be handed over to a 2G cell during an inter-RAT
handover, the RNC forbids the UE to attempt a handover to the
2G cell in a certain period. When this switch is turned on, the
period is 50s. When this switch is turned off, the period is 30s. 8.
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH: When this

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D14
01
02
W
RF
D02
06
05
01
W
RF
D01
02
02
W
RF
D02
04
00
03
W
RF
D02
04
02
W
RF
D02
04
00

er
CS
Fall
bac
k
Gua
rant
ee
for
LTE
Em
erge
ncy
Call
s
SR
NS
Rel
ocat
ion
(UE
Not
Inv
olve
d)
UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LLDC
H,
CE
LL-

Description

switch is turned on, the uplink SRBs of HSUPA 10 ms nonconversational services are always carried on DCHs, and the
original parameter Type of Channel Preferably Carrying
Signaling RB is invalid. When this switch is turned off, SRBs for
HSUPA 10 ms non-conversational services can be carried on
HSUPA channels when the original parameter Type of Channel
Preferably Carrying Signaling RB is set to HSUPA or HSPA. The
switch is set to OFF by default. 9.
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH: When this
switch is turned on, the single-user peak-rate improvement
algorithm of HSUPA 2 ms TTI is enabled. When this switch is
turned off, the algorithm is disabled. The switch is set to OFF by
default. 10. PERFENH_UU_P2D_CUC_OPT_SWITCH: When
this switch is turned on, the P2D cell update confirm message
simplification algorithm takes effect. When this switch is turned
off, the algorithm does not take effect. By default, this switch is
turned off. 11.
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH: This
check box controls whether the RNC considers the converged
SIRTarget value that is used before radio link reconfiguration in
outer loop power control performed after radio link
reconfiguration. If the check box is not selected, the RNC sends
the initial SIRTarget value used after radio link reconfiguration
to the NodeB.If the check box is selected, the RNC selects a
more appropriate value from the initial SIRTarget value used
after radio link reconfiguration and the converged SIRTarget
value used before radio link reconfiguration. Then the RNC
sends the selected value to the NodeB. Setting of this check box
takes effect only when the
PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH check box
is selected. 12. PERFENH_RRC_REDIR_PROTECT_SWITCH:
When this switch is turned on, The mechanism to avoid endless
back-and-forth RRC-redirections takes effect. The switch is set
to OFF by default. 13. PERFENH_H2F_OPT_SWITCH:
whether to enable the optimized algorithm for HSPA UE state
transition from CELL_DCH to CELL_FACH (also referred to as
H2F state transition). When the switch is turned on, the
optimized H2F state transition algorithm is enabled, and event
4A measurement of traffic volume or throughput is added to the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D01
06
36

PC
H,
UR
APC
H,
CE
LLFA
CH)
Inte
r
Syst
em
Red
irec
t
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
DR
D
Intr
odu
ctio
n
Pac
kag
e
SR
B
ove

Description

state transition procedure. The added event 4A measurement


prevents an H2F state transition when data is being transmitted.
14. PERFENH_PSTRAFFIC_P2H_SWITCH: When the switch
is turned on and a CELL_PCH/URA_PCH-to-CELL_DCH (P2D
for short) state transition is triggered for a PS service, the PS
service can be set up on HSPA channels after the state transition.
When the switch is turned off, PS services can be set up only on
DCHs after a P2D state transition. This switch is turned off by
default. 15. PERFENH_VIP_USER_PCHR_MR_SWITCH:
When this switch is turned on, VIP UEs report their transmit
power to the RNC when required and periodically measure
signal quality of intra-frequency cells. In addition, these UEs
measure the downlink BLER, the NodeB measures the uplink
SIR, and the RNC records the measurement results. 16.
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH: Switch
for including the Tx interruption after trigger IE in the uplink 4A
traffic volume measurement control message. When this switch
is turned on, the uplink 4A traffic volume measurement control
message from RNC includes the Tx interruption after trigger IE
for UEs that are in the CELL_FACH or enhanced CELL_FACH
state and processing PS BE services. The value of this IE can be
changed by running the "SET UUESTATETRANS" command.
17.
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH:
The NodeB baseband board uses different processing
specifications for users with different uplink bearer services, for
example, HSUPA TTI 2 ms services, HSUPA TTI 10 ms
services, and R99 services. When serving a large number of
users, the system cannot guarantee that all users can access the
network with the highest service bearer supported by UEs. This
switch controls whether the RNC allocates corresponding
channels for new users based on the cell capability reported
through the NodeB private interface. When this switch is turned
on, the RNC dynamically selects an appropriate uplink service
bearer and allocates corresponding channels for new users to
maximize the system capacity based on the actual NodeB
processing specifications. When this switch is turned off, the
optimization process is disabled. 18.
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
r
HS
UP
A

Description

Whether to use the optimized TTI switching algorithm for BE


services When this switch is turned off, the optimized algorithm
does not take effect. The original mechanism is implemented.
When this switch is turned on, the optimized algorithm takes
effect. After HSUPA services are configured or reconfigured
with 10 ms TTI due to network resource (admission CEs, RTWP,
consumed Iub bandwidth, or consumed CEs) congestion or
insufficient coverage, these UEs cannot change to use 2 ms TTI
if no data needs to be transmitted. 19.
PERFENH_DOWNLOAD_ENHANCE_SWITCH: Whether to
activate the algorithm for increasing the single-threaded
download rate. 20. PERFENH_OLPC_BLER_COEF_ADJUST:
Switch for adjusting the BLER coefficient specific to CS
services based on the best cell's uplink load status. When this
switch is turned on, the outer loop power control algorithm uses
the target BLER set by the OMU board if the best cell's uplink
load status is LDR or OLC. If the status is neither LDR nor
OLC, this algorithm uses this target BLER after being divided by
five. 21. PERFENH_EMG_AGPS_MC_DELAY_SWITCH:
Whether to enable the function of delaying the sending of an
RRC_MEAS_CTRL message containing AGPS information
when an emergency call is made. When this switch is turned on,
the RNC delays the sending of this message until the emergency
call is successfully set up. When this switch is turned off, the
RNC sends this message upon receiving a
LOCATION_REPORTING_CONTROL message from the CN.
22. PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITCH:
Whether to enable a UE having multiple RLSs to use the value
of "CQIReF" and the value of "CQIFbCk" that are for UEs
having only one RLS. The two parameters can be set by running
the "SET UHSDPCCH" and "ADD UCELLHSDPCCH"
commands. When this switch is turned off, the UE does not use
the values of the two parameters that are for UEs having only
one RLS. When this switch is turned on, the UE uses the values
of the two parameters that are for UEs having only one RLS. 23.
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWITCH:
Whether to enable a RELOCATION REQUIRED message to
contain the IE calculationTimeForCiphering. When this switch is
turned on, static relocation request messages contain the IE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

calculationTimeForCiphering. 24.
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH: Whether to
trigger the DRD procedure and channel switchover from E-DCH
or HS-DSCH to DCH when messages transmitted over the Uu
and Iub interfaces do not arrive in time. When this switch is
turned off, the DRD procedure and channel switchover from EDCH or HS-DSCH to DCH are not triggered if messages
transmitted over the Uu and Iub interfaces do not arrive in time.
When this switch is turned on, the DRD procedure and channel
switchover from E-DCH or HS-DSCH to DCH are triggered if
messages transmitted over the Uu and Iub interfaces do not
arrive in time. 25.
PERFENH_CELL_CACLOAD_BROADCAST_AMEND:
Whether to consider CE or code resource usage when
determining the resource status of a cell whose serving boards or
CP sub-systems are different from those of its neighboring cells.
When this switch is turned on, the RNC determines the resource
status of such a cell based on power, CE, and code resource
usage. If power, CE, or code resources in a cell become
congested, the RNC determines that the cell experiences
resource congestion. When this switch is turned off, the RNC
determines the resource status of such a cell based on power
resource usage only. 26.
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH: When this
switch is turned on, candidate cells are ranked by
"InterFreqMeasQuantity" (in the "ADD
UCELLMBDRINTERFREQ" command) for MBDR, and the
cell with the best signal quality is selected as the target cell.
When this switch is turned off, candidate cells are not ranked by
InterFreqMeasQuantity for MBDR. 27.
PERFENH_RRC_DRD_PREADMISSION_SWITCH: Whether
the RNC makes a pre-admission decision on intra-RAT DRDs or
redirections during an RRC connection setup. When this switch
is turned on, the RNC makes a pre-admission decision on intraRAT DRDs or redirections during an RRC connection setup.
When this switch is turned off, the RNC does not make a preadmission decision on intra-RAT DRDs or redirections during an
RRC connection setup. 28.
PERFENH_RRC_WEAK_REDIR_SWITCH: Whether to

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

activate the RRC redirection in weak coverage algorithm. When


this switch is turned on, UEs located in weak coverage are
redirected to the neighboring GSM cell through RRC redirection.
When this switch is turned off, this algorithm is disabled. 29.
PERFENH_L2U_CSFB_COMMCALL_SWITCH: Whether to
preferentially admit PS services of UEs involved in LTE-toUMTS CS fallback. When this switch is turned on: If a UE
involved in a LTE-to-UMTS CS fallback is processing a nonreal-time PS service, the channel type and initial data rate for the
PS service are determined by the "NRTInitRateforL2U"
parameter in the "SET UFRC" command during service
admission. If the UE is processing a real-time PS service, the UE
follows the standard access procedure. If the access attempt fails
and the "PreemptAlgoSwitch" in the "SET
UQUEUEPREEMPT" command is turned on, the UE can
preempt radio resources of existing UEs in the UMTS cell. When
this switch is turned off, the UE follows the standard access
procedure for the PS service. 30.
PERFENH_DLBLINDDETECT_WHEN_ONLYSRBONDCH:
This parameter controls whether to enable blind detection for the
HSDPA user-associated single-signaling R99 channel. When the
switch specified by this parameter is turned on, blind detection is
enabled. 31.
PERFENH_DLBLINDDETECT_WHEN_SRBAMRONDCH:
This parameter controls whether to enable blind detection for the
HSDPA user-associated AMR R99 channel. When the switch
specified by this parameter is turned on, blind detection is
enabled if the HSDPA service has been set up and there are
signaling and AMR traffic carried on the R99 channel. 32.
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT: Whether
to allow R6 UEs to switch from HSUPA 10 ms to 2 ms TTI.
When the switch is turned on, this switching is not allowed for
R6 UEs. When the switch is turned off, this limit does not work.
This parameter is an advanced parameter. To modify this
parameter, contact Huawei Customer Service Center for
technical support.
GUI Value Range: PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH,
PERFENH_RRC_REDIR_PROTECT_SWITCH,
PERFENH_H2F_OPT_SWITCH,
PERFENH_PSTRAFFIC_P2H_SWITCH,
PERFENH_VIP_USER_PCHR_MR_SWITCH,
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH,
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH,
PERFENH_DOWNLOAD_ENHANCE_SWITCH,
PERFENH_OLPC_BLER_COEF_ADJUST,
PERFENH_EMG_AGPS_MC_DELAY_SWITCH,
PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITCH,
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWITCH,
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH,
PERFENH_CELL_CACLOAD_BROADCAST_AMEND,
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH,
PERFENH_RRC_DRD_PREADMISSION_SWITCH,
PERFENH_RRC_WEAK_REDIR_SWITCH,
PERFENH_L2U_CSFB_COMMCALL_SWITCH,
PERFENH_DLBLINDDETECT_WHEN_ONLYSRBONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAMRONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Unit: None
Actual Value Range: PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,
PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH,
PERFENH_RRC_REDIR_PROTECT_SWITCH,
PERFENH_H2F_OPT_SWITCH,
PERFENH_PSTRAFFIC_P2H_SWITCH,
PERFENH_VIP_USER_PCHR_MR_SWITCH,
PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH,
PERFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH,
PERFENH_DOWNLOAD_ENHANCE_SWITCH,
PERFENH_OLPC_BLER_COEF_ADJUST,
PERFENH_EMG_AGPS_MC_DELAY_SWITCH,
PERFENH_MULTI_RLS_CQI_PARA_OPT_SWITCH,
PERFENH_RELOC_IE_CALCTIMEFORCIP_SWITCH,
PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH,
PERFENH_CELL_CACLOAD_BROADCAST_AMEND,
PERFENH_MBDR_TARCELLSEL_OPT_SWITCH,
PERFENH_RRC_DRD_PREADMISSION_SWITCH,
PERFENH_RRC_WEAK_REDIR_SWITCH,
PERFENH_L2U_CSFB_COMMCALL_SWITCH,
PERFENH_DLBLINDDETECT_WHEN_ONLYSRBONDCH,
PERFENH_DLBLINDDETECT_WHEN_SRBAMRONDCH,
PERFENH_R6_HSUPA_TTI_10MSTO2MS_LIMIT
Default Value:
PERFENH_AMR_SPEC_BR_SWITCH:1,PERFENH_AMR_T
MPLT_SWITCH:1,PERFENH_SRB_TMPLT_SWITCH:1,PER
FENH_OLPC_TMPLT_SWITCH:1,PERFENH_AMR_SP_TMP
LT_SWITCH:1,PERFENH_INTRAFREQ_MC_TMPLT_SWIT
CH:1,PERFENH_INTERRAT_PENALTY_50_SWITCH:1,PER
FENH_SRB_OVER_HSUPA_TTI10_SWITCH:0,PERFENH_H
SUPA_TTI2_ENHANCE_SWITCH:0,PERFENH_UU_P2D_C
UC_OPT_SWITCH:0,PERFENH_RL_RECFG_SIR_CONSIDE
R_SWITCH:1,PERFENH_RRC_REDIR_PROTECT_SWITCH:
0,PERFENH_H2F_OPT_SWITCH:0,PERFENH_PSTRAFFIC_
P2H_SWITCH:0,PERFENH_VIP_USER_PCHR_MR_SWITC
H:0,PERFENH_TX_INTERRUPT_AFT_TRIG_SWITCH:0,PE
RFENH_CELL_HSUPA_CAP_CHANGE_OPT_SWITCH:0,
PERFENH_HSUPA_TTI_RECFG_PROC_OPT_SWITCH:0,PE
RFENH_DOWNLOAD_ENHANCE_SWITCH:0,PERFENH_O

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

LPC_BLER_COEF_ADJUST:1,PERFENH_EMG_AGPS_MC_
DELAY_SWITCH:0,PERFENH_MULTI_RLS_CQI_PARA_OP
T_SWITCH:0,PERFENH_RELOC_IE_CALCTIMEFORCIP_S
WITCH:0,PERFENH_IS_TIMEOUT_TRIG_DRD_SWITCH:0,
PERFENH_CELL_CACLOAD_BROADCAST_AMEND:1,PE
RFENH_MBDR_TARCELLSEL_OPT_SWITCH:0,PERFENH_
RRC_DRD_PREADMISSION_SWITCH:0,PERFENH_RRC_
WEAK_REDIR_SWITCH:0,PERFENH_L2U_CSFB_COMMC
ALL_SWITCH:0,PERFENH_DLBLINDDETECT_WHEN_ON
LYSRBONDCH:0,PERFENH_DLBLINDDETECT_WHEN_SR
BAMRONDCH:0,PERFENH_R6_HSUPA_TTI_10MSTO2MS_
LIMIT:0
PROC
ESSS
WITC
H4

B
S
C
6
9
0
0

SET
URR
CTRL
SWIT
CH

W
RF
D01
05
10
W
RF
D01
06
09
02
W
RF
D01
01
01
W
RF
D14
02
26
W

3.4/
6.8/
13.6
/27.
2Kb
ps
RR
C
Con
nect
ion
and
Rad
io
Acc
ess
Bea
rer
Esta
blis
hme
nt
and
Rel
ease
Co

Meaning: 1) AMR_HHO_FAIL_ROLLBACK_SWITCH (Hard


Handover Failure Rollback Switch for CS AMR Speech
Services) 1: This switch is turned on. The RNC supports rollback
caused by failed hard handovers of CS AMR speech services. It
is recommended that the timer T312 be set to 1 second (SET
UCONNMODETIMER: T312=1;) before turning on this switch.
If the timer T312 is not set to 1 second, AMR noise will occur on
some UEs. If the AMRC feature is enabled, the RNC supports
the hard handover failure rollback of only for 12.2 kbit/s
narrowband AMR services. 0: This switch is turned off. The
RNC does not support rollback caused by failed hard handovers
of CS AMR speech services, leading to call drops. 2)
RRC_CONN_SETUP_OPT_SWITCH (RRC CONNECTION
SETUP Message Optimization Switch) Whether optimization of
the RRC CONNECTION SETUP message takes effect. 1: This
switch is turned on. Optimization of the RRC CONNECTION
SETUP message takes effect. If the IE RLC info under SRB3 or
SRB4 in the RRC CONNECTION SETUP message contains the
same information as that under SRB2, the RNC replaces the IE
RLC info under SRB3 or SRB4 with the IE same as RB:0x2(2)
to shorten the length of the message. 0: This switch is turned off.
The RNC does not replace the IE RLC info under SRB3 or
SRB4 in the RRC CONNECTION SETUP message. 3)
PS_F2D_OVERLAP_CELLUPT_SWITCH (Switch for
Simultaneous PS Service Setup F2D and Cell Update
Procedures) During the PS service setup, the RNC undoes a

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D14
01
03
W
RF
D02
04
00
02
W
RF
D14
02
05
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
04
W
RF

mbi
nati
on
of
One
CS
Ser
vice
and
One
PS
Ser
vice
3G
PP
R9
Spe
cifi
cati
ons
Fast
Ret
urn
fro
m
UM
TS
to
LTE
Call
Ree
stab
lish
men
t
Inte
r
Syst
em

Description

CELL_FACH-to-CELL_DCH (F2D for short) procedure when it


receives a Cell Update message with the cause value "cell
reselection" during the F2D procedure. 1: This switch is turned
on. The RNC temporarily does not send the
RANAP_RAB_ASSIGNMENT_RESP message to the CN after
the F2D procedure is undone and waits until the Cell Update
message is processed and the PS service is set up successfully. 0:
This switch is turned off. The RNC directly responds to the CN
with a RANAP_RAB_ASSIGNMENT_RESP message with the
cause value "IU_UNSPEC_FAIL" after the F2D procedure is
undone, indicating that the PS service fails to be set up. 4)
TCP_ACK_ACCELERATOR_SWITCH (Switch for Throughput
Increase in the Case of Simultaneous uplink and downlink
Transmissions) This switch is turned on to increase the total
throughput in the uplink and downlink only when uplink and
downlink HSPA data is transmitted simultaneously. In other
scenarios, you are advised to turn off the switch. 1: This switch
is turned on. The function of increasing the total throughput in
the case of simultaneous uplink and downlink transmissions
takes effect. 0: This switch is turned off. The function of
increasing the total throughput in the case of simultaneous uplink
and downlink transmissions does not take effect. 5)
PHY_RECFG_REEST_SWITCH (Switch for RL
Reestablishments During the Physical Channel Reconfiguration)
1: This switch is turned on. When UE sends the RNC a Cell
Update message with the cause value "Radio Link Failure", the
RNC reestablishes the radio link for the UE under the following
conditions: The UE has not responded to the Physical Channel
Reconfiguration message. The RNC detects interrupted downlink
transmission on SRB2 or the NodeB reports that all radio links
of the UE are out of synchronization. 0: This switch is turned off.
The RNC does not reestablish the radio link for the UE under the
preceding conditions. 6) IUR_RL_REEST_SWITCH (Iur RL
Reestablishment Switch) 1: This switch is turned on. The RNC
deletes the existing Iur radio links for the UE during the RNC
performing radio link reestablishment. 0: This switch is turned
off. The RNC does not delete the existing Iur radio links during
the RNC performing radio link reestablishment. 7)
RB_SETUP_RL_REEST_SWITCH (Switch for RL

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
03
05
W
RF
D02
03
06

Dir
ect
Retr
y
Voi
ce
Ser
vice
Exp
erie
nce
Imp
rov
eme
nt
for
Wea
k
Rec
epti
on
Ues
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte

Description

Reestablishment or Cell Update During an RB Setup) 1: This


switch is turned on. When the RNC is waiting for a UE's
response during a radio bearer (RB) setup CELL_DCH-toCELL_DCH (D2D) procedure: The RNC reestablishes a radio
link (RL) for the UE if the RNC detects a signaling radio bearer
(SRB) reset at layer 2 (L2) or all uplink RLs for the UE are out
of synchronization upon expiration of the RL Restore timer. The
RNC performs a cell update if the RNC receives a CELL
UPDATE message with the cause value of RL FAILURE, RLC
UNRECOVERABLE ERROR, or REENTERED SERVICE
AREA. 0: This switch is turned off. When the RNC is waiting
for a UE's response during an RB setup D2D procedure, the
RNC does not perform an RL reestablishment or cell update
even if the trigger conditions are met. 8)
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH (The
CELL_FACH-to-CELL_DCH state (F2D) transition switch by
TRB reset) When the RNC receives a TRB reset request from a
UE in the CELL_FACH state, the RNC cannot respond to the
UE with a confirm message if the FACH is congested. The
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH
parameter specifies whether a UE performs an F2D transition if
the number of TRB reset requests from the UE to the RNC
reaches a specified threshold. 1: This switch is turned on. The
UE moves from the CELL_FACH state to the CELL_DCH state.
0: This switch is turned off. The UE does not move from the
CELL_FACH state to the CELL_DCH state. This function helps
to reduce the number of call drops caused by the RNC not
responding to the TRB reset requests during FACH congestion.
9) SEND_MSG_NULL_SWITCH (MM NULL Message
Switch) Whether the RNC sends an MM NULL message to the
CS CN. If the switch RNC_CS_QUERY_UE_IMEI_SWITCH
under PROCESSSWITCH2 in the SET URRCTRLSWITCH
command is turned on, testing the interworking between the
RNC and the CN is required. If the CN needs to verify the serial
number of direct transfer messages, turn on this switch. The
RNC rather than the CS CN sends an IDENTITY REQUEST
message to a UE to obtain its IMEI. Upon receiving an
IDENTITY RESPONSE message from the UE: 1: This switch is
turned on. The RNC sends an MM NULL message to the CS

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser

Description

CN. 0: This switch is turned off. The RNC does not send an MM
NULL message to the CS CN.
10)FD_PCH_IUR_CS_OPT_SWITCH CS paging message
processing switch for UEs in the CELL_PCH or URA_PCH
state that support fast dormancy on the drift radio network
controller (DRNC) side. 1: This switch is turned on. The SRNC
instructs these UEs to transition to the CELL_DCH state and to
establish CS services when these UEs receive a CS paging
message. 0: This switch is turned off. The SRNC releases the
connection of these UEs when these UEs receive a CS paging
message.
11)CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH
Whether the RNC releases the connection of a UE in a state
other than CELL_DCH when the T314/T315 timer in the cell
update message received by the UE expires. 1: This switch is
turned on. The RNC continues with the cell update processing
when the T314/T315 timer in the cell update message expires. 0:
This switch is turned off. The RNC abnormally releases the
connection of the UE when the T314/T315 timer in the cell
update message expires. 12)
CS_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for CS HHO) 1: This switch is turned on.
The RNC does not put the activation time information element
(IE) in the hard handover configuration message for CS services.
After receiving the message, the UE immediately activates the
configuration. 0: This switch is turned off. The RNC puts the
activation time IE in the hard handover configuration message
for CS services. After receiving the message, the UE activates
the configuration at the specified activation time. 13)
PS_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for PS HHO) 1: This switch is turned on.
The RNC does not put the activation time information element
(IE) in the hard handover configuration message for PS services.
After receiving the message, the UE immediately activates the
configuration. 0: This switch is turned off. The RNC puts the
activation time IE in the hard handover configuration message
for PS services. After receiving the message, the UE activates the
configuration at the specified activation time. 14)
IUR_HHO_ASYNC_CTRL_SWITCH(Asynchronous

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Description

Reconfigure Switch for Iur HHO) 1: This switch is turned on.


The RNC does not put the activation time information element
(IE) in the hard handover configuration message across the Iur
interface. After receiving the message, the UE immediately
activates the configuration. 0: This switch is turned off. The
RNC puts the activation time IE in the hard handover
configuration message across the Iur interface. After receiving
the message, the UE activates the configuration at the specified
activation time. 15) R8_UE_SEL_DPUE_SWITCH (Switch for
Preferentially Allocating DPUe Resources to UEs That Comply
with 3GPP Release 8 or Later) 1: This switch is turned on. The
RNC preferentially allocates DPUe resources in any subrack to
UEs that comply with 3GPP Release 8 or later. 0: This switch is
turned off. The RNC preferentially allocates DPU resources in
the subrack that the UEs access to UEs that comply with 3GPP
Release 8 or later. The RNC allocates DPU resources in other
subracks only when the amount of consumed DPU resources in
this subrack exceeds a preset threshold for inter-subrack resource
sharing. 16) F2P_DATATRANS_OPTIMIZE_SWITCH(Switch
for Optimized Data Transmission before a State Transition from
CELL_FACH to CELL_PCH or URA_PCH) Whether the RNC
queries the RLC state before and after a UE moves from the
CELL_FACH state to the CELL_PCH or URA_PCH state due to
event 4B. A UE in the CELL_FACH state can move to the
CELL_PCH or URA_PCH state even when there is downlink
data transmission for the UE. When this occurs, data packets are
suspended on the RNC side. This switch is introduced to solve
this problem. 1: This switch is turned on. The RNC queries the
RLC state before a UE moves from the CELL_FACH state to the
CELL_PCH or URA_PCH state due to event 4B. If the state
query fails, the UE does not perform the state transition. If the
state query succeeds, the UE continues with the state transition.
The RNC queries the RLC state again after the state transition is
complete and before the L2 link is deactivated. If there is SRB3,
SRB4, or TRB data to be transmitted to the UE on the RLC, the
paging procedure is triggered. 0: This switch is turned off. The
original state transition from CELL_FACH to CELL_PCH or
URA_PCH is used. This parameter is an advanced parameter. To
modify this parameter, contact Huawei Customer Service Center

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

for technical support.


17)IRATHO_HOCANCEL_RL_REEST_SWITCH(Switch for
RL Reestablishments During the inter-RAT Handover) 1: This
switch is turned on. The RNC reestablishes a radio link (RL) for
the UE during a inter-RAT Handover procedure if the RNC
detects a signaling radio bearer (SRB) reset at layer 2 (L2) or all
uplink RLs for the UE are out of synchronization upon
expiration of the RL Restore timer after the RNC sends UE a
HANDOVER FROM UTRAN COMMAND message or a CELL
CHANGE ORDER FROM UTRAN message and UE fails to
receive these two messages. 0: This switch is turned off. The
RNC does not reestablish the radio link for the UE under the
preceding conditions.
18)TRB_RESET_RL_REEST_SWITCH(Switch for RL
Reestablishments Triggered by TRB RESET) 1: This switch is
turned on. The RNC reestablishes a radio link (RL) for the UE if
the RNC detects a traffic radio bearer (TRB) reset at layer 2 (L2)
under the following conditions: UE is in CELL_DCH state and
UE is not in any signaling procedure. UE has only one PS RAB.
0: This switch is turned off. The RNC does not reestablish the
radio link for the UE under the preceding conditions.
19)RB_REL_RL_REEST_SWITCH(Switch for RL
Reestablishments During a PS RB Release) 1: This switch is
turned on. The RNC reestablishes a radio link (RL) for the UE
during a PS radio bearer (RB) release procedure under the
following conditions: The RNC detects a signaling radio bearer
(SRB) reset at layer 2 (L2) or all uplink RLs for the UE are out
of synchronization upon expiration of the RL Restore timer or
UE has no response to RNC after RNC sends UE a RADIO
BEARER RELEASE message. The UE has both CS RAB and
PS RAB. The UE is in CELL_DCH state. It is recommended that
this switch be used together with the
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH in the
"OptimizationSwitch4" parameter in the "SET
URRCTRLSWITCH" command. 0: This switch is turned off.
The RNC does not reestablish the radio link for the UE under the
preceding conditions.
20)RB_SETUP_ENHANCE_RL_REEST_SWITCH(Switch for
Enhanced RL Reestablishments During an RB setup) 1: This

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

switch is turned on. The RNC reestablishes a radio link (RL) for
the UE during a radio bearer (RB) setup CELL_DCH-toCELL_DCH (D2D) procedure under the following conditions:
The RNC detects a signaling radio bearer (SRB) reset at layer 2
(L2) or all uplink RLs for the UE are out of synchronization
upon expiration of the RL Restore timer and the UE has received
the RADIO BEARER SETUP message. The UE has no response
to the RNC after the RNC sends UE a RADIO BEARER SETUP
message. The switch RB_SETUP_RL_REEST_SWITCH under
"PROCESSSWITCH4" in the "SET URRCTRLSWITCH"
command should be turned on. And it is recommended that the
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH and
RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH in
the "OptimizationSwitch4" parameter in the "SET
URRCTRLSWITCH" command be set to on. 0: This switch is
turned off. The RNC does not reestablish the radio link for the
UE under the preceding conditions.
21)RAB_SETUPMOD_CNT_FIX_SWITCH Whether to correct
the methods for measuring the counters related to RAB setup or
reconfiguration failures of UEs in the CELL_FACH state. The
RAB setup or reconfiguration is triggered by the F2F or F2D
state transition. This switch is turned off by default. 1: This
switch is turned on. The measurement methods of these counters
are corrected based on the measurement points. 0: This switch is
turned off. The measurement methods of these counters remain
unchanged.
22)PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH
Whether to reestablish the call for the UE that sends a CELL
UPDATE message with the cause value "RLC unrecoverable
error" in the CELL_PCH or URA_PCH state. 1: This switch is
turned on. The RNC reestablishes the call for the UE that sends a
CELL UPDATE message with the cause value "RLC
unrecoverable error" in the CELL_PCH or URA_PCH state. 0:
This switch is turned off. The RNC does not reestablish the call
for the UE that sends a CELL UPDATE message with the cause
value "RLC unrecoverable error" in the CELL_PCH or
URA_PCH state.
23)FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH
Whether a UMTS/LTE UE performs fast cell reselection. 1: This

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

switch is turned on. If the best cell is configured with a


neighboring LTE cell and its priority is lower than the priority of
the neighboring LTE cell, the UE performs fast cell reselection.
0: This switch is turned off. The UE does not perform fast cell
reselection.
24)UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH Whether a
UMTS/LTE UE transits from CELL_DCH to CELL_PCH or
from CELL_DCH to the idle mode when an inactivity timer
expires. The inactivity timer is specified by the
PsInactTmrForFstDrmDch parameter in the SET
UPSINACTTIMER command. 1: This switch is turned on. The
UMTS/LTE UE transits from CELL_DCH to the idle mode
when the inactivity timer expires. 0: This switch is turned off.
The UMTS/LTE UE transits from the CELL_DCH to
CELL_PCH when the inactivity timer expires.
25)PHYCHRECFG_ENH_RL_REEST_SWITCH Whether the
enhanced function of call reestablishment during physical
channel reconfiguration takes effect. Whether to preferentially
process a CELL UPDATE message when physical channel
reconfiguration is in progress. The RNC receives a CELL
UPDATE message from a UE with a cause value of "radio link
failure", "RLC unrecoverable error", or "re-entering service area"
when expecting a response from the UE to the physical channel
reconfiguration process. In this scenario, 1: This switch is turned
on. The RNC preferentially processes the CELL UPDATE
message. 0: This switch is turned off. The RNC does not
preferentially process the CELL UPDATE message. This
parameter takes effect only when the
PHYCHRECFG_ENH_RL_REEST_SWITCH check box under
the "PROCESSSWITCH4" parameter in the "SET
URRCTRLSWITCH" command is selected.
26)RBRECFG_ENH_RL_REEST_SWITCH Whether the
enhanced function of call reestablishment during RB
reconfiguration takes effect. Whether to preferentially process a
CELL UPDATE message when RB reconfiguration is in
progress. The RNC receives a CELL UPDATE message from a
UE with a cause value of "radio link failure", "RLC
unrecoverable error", or "re-entering service area" when
expecting a response from the UE to the RB reconfiguration

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

process. In this scenario, 1: This switch is turned on. The RNC


preferentially processes the CELL UPDATE message. It is
recommended that this switch be used together with the
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH in the
"OptimizationSwitch4" parameter in the "SET
URRCTRLSWITCH" command. 0: This switch is turned off.
The RNC does not preferentially process the CELL UPDATE
message. This parameter takes effect only when the
RB_RECFG_RL_REEST_SWITCH check box under the
"OptimizationSwitch" parameter in the "SET
URRCTRLSWITCH" command is selected.
27)SMC_STOP_RLC_SWITCH Whether to stop RLC entities
(except RLC entities used by SRB2) for security-mode-enabled
UEs whose user signaling (except cell-related signaling) is
processed by their overflow RNCs due to load sharing and that
are in the security mode. 1: This switch is turned on. The RNC
stops RLC entities (except RLC entities used by SRB2) for such
UEs. This prevents call drops that are caused by the ciphering
activation time inconsistency between the UEs and RNC. 0: This
switch is turned off. The RNC suspends RLC entities (except
RLC entities used by SRB2) for such UEs.
28)GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH
Whether the RAB RELEASE REQUEST or IU RELEASE
COMPLETE message carries the IE GTP PDU SN during the
release procedure initiated by the UTRAN of the PS domain. 1:
This switch is turned on. The RAB RELEASE REQUEST or IU
RELEASE COMPLETE message carries the IE GTP PDU SN.
For details, see 3GPP TS 25.413. 0: This switch is turned off.
The RAB RELEASE REQUEST or IU RELEASE COMPLETE
message does not carry the IE GTP PDU SN.
29)CMP_IU_QOS_GTP_PDU_SN_SWITCH Whether to allow
the compatibility processing of reordering the GTP-U DL
transmission if the RAB ASSIGNMENT REQUEST message
carries the IE Delivery Order with the value of delivery-orderrequested. 1: This switch is turned on. The GTP-U DL
transmission is not reordered. 0: This switch is turned off. The
GTP-U DL transmission uses the DL GTP PDU SN carried by
the RAB ASSIGNMENT REQUEST message as the first SN for
reordering. 30)DL_TRB_RESET_BUFF_SWITCH Whether not

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

to immediately process a TRB RESET message if the


corresponding TRB resets when an RRC-related process is in
progress. Note that the RRC-related process is a process that is
initiated after the UE in question has set up a service. 1: This
switch is turned on, The RNC processes the message after the
RRC-related process is complete. 0: This switch is turned off,
The RNC immediately processes the message, releases the RAB
of the UE, and notifies the CN that the release is an abnormal
release.
31)RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH
Whether to trigger a CELL_FACH-to-CELL_DCH state
transition for a UE not performing any RRC-related process if
the RNC detects a TRB reset. 1: This switch is turned on. The
RNC triggers a CELL_FACH-to-CELL_DCH state transition for
such a UE upon detecting a TRB reset. 0: This switch is turned
off. The RNC directly releases the service of the UE and notifies
the CN that the release is an abnormal release.
32)RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH Whether to
allow data transmission when the RNC receives a RAB
ASSIGNMENT REQUEST message that carries the transport
layer information after the PS service has been established. 1:
This switch is turned on. The RNC reconfigures the transport
layer information and continues with data transmission. For
details, see 3GPP TS 25.413. 0: This switch is turned off. The
RNC does not reconfigure the transport layer information and
data cannot be transmitted.
GUI Value Range: PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH, IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH,
SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

R8_UE_SEL_DPUE_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH,
CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Unit: None
Actual Value Range:
PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH, IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH,
SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
R8_UE_SEL_DPUE_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH,
CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Default Value:
PS_F2D_OVERLAP_CELLUPT_SWITCH:0,AMR_HHO_FAI
L_ROLLBACK_SWITCH:0,PHY_RECFG_REEST_SWITCH:
0,IUR_RL_REEST_SWITCH:0,RB_SETUP_RL_REEST_SWI
TCH:0,RRC_CONN_SETUP_OPT_SWITCH:0,TCP_ACK_AC
CELERATOR_SWITCH:0,RRC_CELLFACH_TRB_RESET_T
O_F2D_SWITCH:0,SEND_MSG_NULL_SWITCH:0,FD_PCH
_IUR_CS_OPT_SWITCH:0,CELLUPT_T314_T315_TIMEOU
T_OPT_SWITCH:0,CS_HHO_ASYNC_CTRL_SWITCH:0,PS_
HHO_ASYNC_CTRL_SWITCH:0,IUR_HHO_ASYNC_CTRL
_SWITCH:0,R8_UE_SEL_DPUE_SWITCH:0,F2P_DATATRA
NS_OPTIMIZE_SWITCH:0,IRATHO_HOCANCEL_RL_REES
T_SWITCH:0,TRB_RESET_RL_REEST_SWITCH:0,RB_REL
_RL_REEST_SWITCH:0,RB_SETUP_ENHANCE_RL_REES
T_SWITCH:0,RAB_SETUPMOD_CNT_FIX_SWITCH:0,PCH
_UE_RLC_UNRECOVERABLEERROR_SWITCH:0,FAST_R
ETURN_LTE_BY_CELL_SELECT_SWITCH:0,UL_DUAL_M
ODE_UE_D2P_OR_D2I_SWITCH:0,PHYCHRECFG_ENH_R
L_REEST_SWITCH:0,RBRECFG_ENH_RL_REEST_SWITC
H:0,SMC_STOP_RLC_SWITCH:1,GTP_SN_IN_RAB_REL_I
NIT_BY_UTRAN_SWITCH:1,CMP_IU_QOS_GTP_PDU_SN
_SWITCH:0,DL_TRB_RESET_BUFF_SWITCH:0,RRC_CELL
FACH_DL_TRB_RESET_TO_F2D_SWITCH:0,RAB_ASS_M
OD_TNL_ADDR_SUP_SWITCH:1
Proces B SET
sSwitc S URR

W 3.4/ Meaning: 1) AMR_HHO_FAIL_ROLLBACK_SWITCH (Hard


RF 6.8/ Handover Failure Rollback Switch for CS AMR Speech

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
h4

Description

C CTRL D- 13.6 Services) 1: This switch is turned on. The RNC supports rollback
6 SWIT 01 /27. caused by failed hard handovers of CS AMR speech services. It
9 CH
05 2Kb is recommended that the timer T312 be set to 1 second (SET
1
10 ps
UCONNMODETIMER: T312=1;) before turning on this switch.
0
W RR If the timer T312 is not set to 1 second, AMR noise will occur on
some UEs. If the AMRC feature is enabled, the RNC supports
RF C
D- Con the hard handover failure rollback of only for 12.2 kbit/s
01 nect narrowband AMR services. 0: This switch is turned off. The
06 ion RNC does not support rollback caused by failed hard handovers
09 and of CS AMR speech services, leading to call drops. 2)
02 Rad RRC_CONN_SETUP_OPT_SWITCH (RRC CONNECTION
SETUP Message Optimization Switch) Whether optimization of
W io
RF Acc the RRC CONNECTION SETUP message takes effect. 1: This
D- ess switch is turned on. Optimization of the RRC CONNECTION
01 Bea SETUP message takes effect. If the IE RLC info under SRB3 or
01 rer SRB4 in the RRC CONNECTION SETUP message contains the
01 Esta same information as that under SRB2, the RNC replaces the IE
blis RLC info under SRB3 or SRB4 with the IE same as RB:0x2(2)
W
hme to shorten the length of the message. 0: This switch is turned off.
RF
nt
The RNC does not replace the IE RLC info under SRB3 or
Dand SRB4 in the RRC CONNECTION SETUP message. 3)
14
Rel PS_F2D_OVERLAP_CELLUPT_SWITCH (Switch for
02
ease Simultaneous PS Service Setup F2D and Cell Update
26
Co Procedures) During the PS service setup, the RNC undoes a
W
mbi CELL_FACH-to-CELL_DCH (F2D for short) procedure when it
RF
nati receives a Cell Update message with the cause value "cell
Don reselection" during the F2D procedure. 1: This switch is turned
14
on. The RNC temporarily does not send the
of
01
One RANAP_RAB_ASSIGNMENT_RESP message to the CN after
03
CS the F2D procedure is undone and waits until the Cell Update
W Ser message is processed and the PS service is set up successfully. 0:
RF vice This switch is turned off. The RNC directly responds to the CN
D- and with a RANAP_RAB_ASSIGNMENT_RESP message with the
02 One cause value "IU_UNSPEC_FAIL" after the F2D procedure is
04 PS undone, indicating that the PS service fails to be set up. 4)
00 Ser TCP_ACK_ACCELERATOR_SWITCH (Switch for Throughput
02 vice Increase in the Case of Simultaneous uplink and downlink
W 3G Transmissions) This switch is turned on to increase the total
RF PP throughput in the uplink and downlink only when uplink and

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D14
02
05
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
04
W
RF
D02
03
05
W
RF
D02
03
06

R9
Spe
cifi
cati
ons
Fast
Ret
urn
fro
m
UM
TS
to
LTE
Call
Ree
stab
lish
men
t
Inte
r
Syst
em
Dir
ect
Retr
y
Voi
ce
Ser
vice
Exp
erie
nce
Imp
rov
eme
nt

Description

downlink HSPA data is transmitted simultaneously. In other


scenarios, you are advised to turn off the switch. 1: This switch
is turned on. The function of increasing the total throughput in
the case of simultaneous uplink and downlink transmissions
takes effect. 0: This switch is turned off. The function of
increasing the total throughput in the case of simultaneous uplink
and downlink transmissions does not take effect. 5)
PHY_RECFG_REEST_SWITCH (Switch for RL
Reestablishments During the Physical Channel Reconfiguration)
1: This switch is turned on. The UE sends the RNC a Cell
Update message with the cause value "Radio Link Failure" and
the RNC reestablishes the radio link for the UE under the
following conditions: The UE has not responded to the Physical
Channel Reconfiguration message. The RNC detects interrupted
downlink transmission on SRB2 or the NodeB reports that all
radio links of the UE are out of synchronization. 0: This switch is
turned off. The RNC does not reestablish the radio link for the
UE under the preceding conditions. 6)
IUR_RL_REEST_SWITCH (Iur RL Reestablishment Switch) 1:
This switch is turned on. The RNC deletes the existing Iur radio
links for the UE during the RNC performing radio link
reestablishment. 0: This switch is turned off. The RNC does not
delete the existing Iur radio links during the RNC performing
radio link reestablishment. 7)
RB_SETUP_RL_REEST_SWITCH (Switch for RL
Reestablishment or Cell Update During an RB Setup) 1: This
switch is turned on. When the RNC is waiting for a UE's
response during a radio bearer (RB) setup CELL_DCH-toCELL_DCH (D2D) procedure: The RNC reestablishes a radio
link (RL) for the UE if the RNC detects a signaling radio bearer
(SRB) reset at layer 2 (L2) or all uplink RLs for the UE are out
of synchronization upon expiration of the RL Restore timer. The
RNC performs a cell update if the RNC receives a CELL
UPDATE message with the cause value of RL FAILURE, RLC
UNRECOVERABLE ERROR, or REENTERED SERVICE
AREA. 0: This switch is turned off. When the RNC is waiting
for a UE's response during an RB setup D2D procedure, the
RNC does not perform an RL reestablishment or cell update
even if the trigger conditions are met. 8)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
for
Wea
k
Rec
epti
on
Ues
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre

Description

RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH (The
CELL_FACH-to-CELL_DCH state (F2D) transition switch by
TRB reset) When the RNC receives a TRB reset request from a
UE in the CELL_FACH state, the RNC cannot respond to the
UE with a confirm message if the FACH is congested. The
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH
parameter specifies whether a UE performs an F2D transition if
the number of TRB reset requests from the UE to the RNC
reaches a specified threshold. 1: This switch is turned on. The
UE moves from the CELL_FACH state to the CELL_DCH state.
0: This switch is turned off. The UE does not move from the
CELL_FACH state to the CELL_DCH state. This function helps
to reduce the number of call drops caused by the RNC not
responding to the TRB reset requests during FACH congestion.
9) SEND_MSG_NULL_SWITCH (MM NULL Message
Switch) Whether the RNC sends an MM NULL message to the
CS CN. If the switch RNC_CS_QUERY_UE_IMEI_SWITCH
under PROCESSSWITCH2 in the SET URRCTRLSWITCH
command is turned on, testing the interworking between the
RNC and the CN is required. If the CN needs to verify the serial
number of direct transfer messages, turn on this switch. The
RNC rather than the CS CN sends an IDENTITY REQUEST
message to a UE to obtain its IMEI. Upon receiving an
IDENTITY RESPONSE message from the UE: 1: This switch is
turned on. The RNC sends an MM NULL message to the CS
CN. 0: This switch is turned off. The RNC does not send an MM
NULL message to the CS CN.
10)FD_PCH_IUR_CS_OPT_SWITCH CS paging message
processing switch for UEs in the CELL_PCH or URA_PCH
state that support fast dormancy on the drift radio network
controller (DRNC) side. 1: This switch is turned on. The SRNC
instructs these UEs to transition to the CELL_DCH state and to
establish CS services when these UEs receive a CS paging
message. 0: This switch is turned off. The SRNC releases the
connection of these UEs when these UEs receive a CS paging
message.
11)CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH
Whether the RNC releases the connection of a UE in a state
other than CELL_DCH when the T314/T315 timer in the cell

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Description

update message received by the UE expires. 1: This switch is


turned on. The RNC continues with the cell update processing
when the T314/T315 timer in the cell update message expires. 0:
This switch is turned off. The RNC abnormally releases the
connection of the UE when the T314/T315 timer in the cell
update message expires. 12)
CS_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for CS HHO) 1: This switch is turned on.
The RNC does not put the activation time information element
(IE) in the hard handover configuration message for CS services.
After receiving the message, the UE immediately activates the
configuration. 0: This switch is turned off. The RNC puts the
activation time IE in the hard handover configuration message
for CS services. After receiving the message, the UE activates
the configuration at the specified activation time. 13)
PS_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for PS HHO) 1: This switch is turned on.
The RNC does not put the activation time information element
(IE) in the hard handover configuration message for PS services.
After receiving the message, the UE immediately activates the
configuration. 0: This switch is turned off. The RNC puts the
activation time IE in the hard handover configuration message
for PS services. After receiving the message, the UE activates the
configuration at the specified activation time. 14)
IUR_HHO_ASYNC_CTRL_SWITCH(Asynchronous
Reconfigure Switch for Iur HHO) 1: This switch is turned on.
The RNC does not put the activation time information element
(IE) in the hard handover configuration message across the Iur
interface. After receiving the message, the UE immediately
activates the configuration. 0: This switch is turned off. The
RNC puts the activation time IE in the hard handover
configuration message across the Iur interface. After receiving
the message, the UE activates the configuration at the specified
activation time. 15)
F2P_DATATRANS_OPTIMIZE_SWITCH(Switch for
Optimized Data Transmission before a State Transition from
CELL_FACH to CELL_PCH or URA_PCH) Whether the RNC
queries the RLC state before and after a UE moves from the
CELL_FACH state to the CELL_PCH or URA_PCH state due to

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

event 4B. A UE in the CELL_FACH state can move to the


CELL_PCH or URA_PCH state even when there is downlink
data transmission for the UE. When this occurs, data packets are
suspended on the RNC side. This switch is introduced to solve
this problem. 1: This switch is turned on. The RNC queries the
RLC state before a UE moves from the CELL_FACH state to the
CELL_PCH or URA_PCH state due to event 4B. If the state
query fails, the UE does not perform the state transition. If the
state query succeeds, the UE continues with the state transition.
The RNC queries the RLC state again after the state transition is
complete and before the L2 link is deactivated. If there is SRB3,
SRB4, or TRB data to be transmitted to the UE on the RLC, the
paging procedure is triggered. 0: This switch is turned off. The
original state transition from CELL_FACH to CELL_PCH or
URA_PCH is used. This parameter is an advanced parameter. To
modify this parameter, contact Huawei Customer Service Center
for technical support.
16)IRATHO_HOCANCEL_RL_REEST_SWITCH(Switch for
RL Reestablishments During the inter-RAT Handover) 1: This
switch is turned on. The RNC reestablishes a radio link (RL) for
the UE during a inter-RAT Handover procedure if the RNC
detects a signaling radio bearer (SRB) reset at layer 2 (L2) or all
uplink RLs for the UE are out of synchronization upon
expiration of the RL Restore timer after the RNC sends UE a
HANDOVER FROM UTRAN COMMAND message or a CELL
CHANGE ORDER FROM UTRAN message and UE fails to
receive these two messages. 0: This switch is turned off. The
RNC does not reestablish the radio link for the UE under the
preceding conditions.
17)TRB_RESET_RL_REEST_SWITCH(Switch for RL
Reestablishments Triggered by TRB RESET) 1: This switch is
turned on. The RNC reestablishes a radio link (RL) for the UE if
the RNC detects a traffic radio bearer (TRB) reset at layer 2 (L2)
under the following conditions: UE is in CELL_DCH state and
UE is not in any signaling procedure. UE has only one PS RAB.
0: This switch is turned off. The RNC does not reestablish the
radio link for the UE under the preceding conditions.
18)RB_REL_RL_REEST_SWITCH(Switch for RL
Reestablishments During a PS RB Release) 1: This switch is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

turned on. The RNC reestablishes a radio link (RL) for the UE
during a PS radio bearer (RB) release procedure under the
following conditions: The RNC detects a signaling radio bearer
(SRB) reset at layer 2 (L2) or all uplink RLs for the UE are out
of synchronization upon expiration of the RL Restore timer or
UE has no response to RNC after RNC sends UE a RADIO
BEARER RELEASE message. The UE has both CS RAB and
PS RAB. The UE is in CELL_DCH state. It is recommended that
this switch be used together with the
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH in the
"OptimizationSwitch4" parameter in the "SET
URRCTRLSWITCH" command. 0: This switch is turned off.
The RNC does not reestablish the radio link for the UE under the
preceding conditions.
19)RB_SETUP_ENHANCE_RL_REEST_SWITCH(Switch for
Enhanced RL Reestablishments During an RB setup) 1: This
switch is turned on. The RNC reestablishes a radio link (RL) for
the UE during a radio bearer (RB) setup CELL_DCH-toCELL_DCH (D2D) procedure under the following conditions:
The RNC detects a signaling radio bearer (SRB) reset at layer 2
(L2) or all uplink RLs for the UE are out of synchronization
upon expiration of the RL Restore timer and the UE has received
the RADIO BEARER SETUP message. The UE has no response
to the RNC after the RNC sends UE a RADIO BEARER SETUP
message. The switch RB_SETUP_RL_REEST_SWITCH under
"PROCESSSWITCH4" in the "SET URRCTRLSWITCH"
command should be turned on. And it is recommended that the
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH and
RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH in
the "OptimizationSwitch4" parameter in the "SET
URRCTRLSWITCH" command be set to on. 0: This switch is
turned off. The RNC does not reestablish the radio link for the
UE under the preceding conditions.
20)RAB_SETUPMOD_CNT_FIX_SWITCH Whether to correct
the methods for measuring the counters related to RAB setup or
reconfiguration failures of UEs in the CELL_FACH state. The
RAB setup or reconfiguration is triggered by the F2F or F2D
state transition. This switch is turned off by default. 1: This
switch is turned on. The measurement methods of these counters

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

are corrected based on the measurement points. 0: This switch is


turned off. The measurement methods of these counters remain
unchanged.
21)PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH(RL
Reestablishment Switch for PCH UEs Experiencing RLC
Unrecoverable Errors) Whether the RNC reestablishes the radio
link (RL) for the UE in the CELL_PCH or URA_PCH state after
receiving a cell update message with the cause value "RLC
unrecoverable error" from the UE. 1: This switch is set to on.
When a UE in the CELL_PCH or URA_PCH state sends a cell
update message with the cause value "RLC unrecoverable error",
the RNC reestablishes the RL for the UE. 0: This switch is set to
off. When a UE in the CELL_PCH or URA_PCH state sends a
cell update message with the cause value "RLC unrecoverable
error", the RNC does not reestablish the RL for the UE.
22)FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH
Whether a UMTS/LTE UE performs fast cell reselection. 1: This
switch is turned on. If the best cell is configured with a
neighboring LTE cell and its priority is lower than the priority of
the neighboring LTE cell, the UE performs fast cell reselection.
0: This switch is turned off. The UE does not perform fast cell
reselection.
23)UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH Whether a
UMTS/LTE UE transits from CELL_DCH to CELL_PCH or
from CELL_DCH to the idle mode when an inactivity timer
expires. The inactivity timer is specified by the
PsInactTmrForFstDrmDch parameter in the SET
UPSINACTTIMER command. 1: This switch is turned on. The
UMTS/LTE UE transits from CELL_DCH to the idle mode
when the inactivity timer expires. 0: This switch is turned off.
The UMTS/LTE UE transits from the CELL_DCH to
CELL_PCH when the inactivity timer expires.
24)PHYCHRECFG_ENH_RL_REEST_SWITCH Whether the
enhanced function of call reestablishment during physical
channel reconfiguration takes effect. Whether to preferentially
process a CELL UPDATE message when physical channel
reconfiguration is in progress. The RNC receives a CELL
UPDATE message from a UE with a cause value of "radio link
failure", "RLC unrecoverable error", or "re-entering service area"

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

when expecting a response from the UE to the physical channel


reconfiguration process. In this scenario, 1: This switch is turned
on. The RNC preferentially processes the CELL UPDATE
message. 0: This switch is turned off. The RNC does not
preferentially process the CELL UPDATE message. This
parameter takes effect only when the
PHYCHRECFG_ENH_RL_REEST_SWITCH check box under
the "PROCESSSWITCH4" parameter in the "SET
URRCTRLSWITCH" command is selected.
25)RBRECFG_ENH_RL_REEST_SWITCH Whether the
enhanced function of call reestablishment during RB
reconfiguration takes effect. Whether to preferentially process a
CELL UPDATE message when RB reconfiguration is in
progress. The RNC receives a CELL UPDATE message from a
UE with a cause value of "radio link failure", "RLC
unrecoverable error", or "re-entering service area" when
expecting a response from the UE to the RB reconfiguration
process. In this scenario, 1: This switch is turned on. The RNC
preferentially processes the CELL UPDATE message. It is
recommended that this switch be used together with the
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH in the
"OptimizationSwitch4" parameter in the "SET
URRCTRLSWITCH" command. 0: This switch is turned off.
The RNC does not preferentially process the CELL UPDATE
message in the preceding scenario. This parameter takes effect
only when the RB_RECFG_RL_REEST_SWITCH check box
under the "OptimizationSwitch" parameter in the "SET
URRCTRLSWITCH" command is selected.
26)SMC_STOP_RLC_SWITCH Whether to stop RLC entities
(except RLC entities used by SRB2) for security-mode-enabled
UEs whose user signaling (except cell-related signaling) is
processed by their overflow RNCs due to load sharing and that
are in the security mode. 1: This switch is turned on. The RNC
stops RLC entities (except RLC entities used by SRB2) for such
UEs. This prevents call drops that are caused by the ciphering
activation time inconsistency between the UEs and RNC. 0: This
switch is turned off. The RNC suspends RLC entities (except
RLC entities used by SRB2) for such UEs.
27)GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Whether the RAB RELEASE REQUEST or IU RELEASE


COMPLETE message carries the IE GTP PDU SN during the
release procedure initiated by the UTRAN of the PS domain. 1:
This switch is turned on. The RAB RELEASE REQUEST or IU
RELEASE COMPLETE message carries the IE GTP PDU SN.
For details, see 3GPP TS 25.413. 0: This switch is turned off.
The RAB RELEASE REQUEST or IU RELEASE COMPLETE
message does not carry the IE GTP PDU SN.
28)CMP_IU_QOS_GTP_PDU_SN_SWITCH Whether to allow
the compatibility processing of reordering the GTP-U DL
transmission if the RAB ASSIGNMENT REQUEST message
carries the IE Delivery Order with the value of delivery-orderrequested. 1: This switch is turned on. The GTP-U DL
transmission is not reordered. 0: This switch is turned off. The
GTP-U DL transmission uses the DL GTP PDU SN carried by
the RAB ASSIGNMENT REQUEST message as the first SN for
reordering. 29)DL_TRB_RESET_BUFF_SWITCH Whether not
to immediately process a TRB RESET message if the
corresponding TRB resets when an RRC-related process is in
progress. Note that the RRC-related process is a process that is
initiated after the UE in question has set up a service. 1: This
switch is turned on. The RNC processes the message after the
RRC-related process is complete. 0: This switch is turned off.
The RNC immediately processes the message, releases the RAB
of the UE, and notifies the CN that the release is an abnormal
release.
30)RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH
Whether to trigger a CELL_FACH-to-CELL_DCH state
transition for a UE not performing any RRC-related process if
the RNC detects a TRB reset. 1: This switch is turned on. The
RNC triggers a CELL_FACH-to-CELL_DCH state transition for
such a UE upon detecting a TRB reset. 0: This switch is turned
off. The RNC directly releases the service of the UE and notifies
the CN that the release is an abnormal release.
31)RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH Whether to
allow data transmission when the RNC receives a RAB
ASSIGNMENT REQUEST message that carries the transport
layer information after the PS service has been established. 1:
This switch is turned on. The RNC reconfigures the transport

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

layer information and continues with data transmission. For


details, see 3GPP TS 25.413. 0: This switch is turned off. The
RNC does not reconfigure the transport layer information and
data cannot be transmitted.
GUI Value Range: PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH, IUR_RL_REEST_SWITCH,
RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH,
SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH,
CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Unit: None
Actual Value Range:
PS_F2D_OVERLAP_CELLUPT_SWITCH,
AMR_HHO_FAIL_ROLLBACK_SWITCH,
PHY_RECFG_REEST_SWITCH, IUR_RL_REEST_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RB_SETUP_RL_REEST_SWITCH,
RRC_CONN_SETUP_OPT_SWITCH,
TCP_ACK_ACCELERATOR_SWITCH,
RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH,
SEND_MSG_NULL_SWITCH,
FD_PCH_IUR_CS_OPT_SWITCH,
CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH,
CS_HHO_ASYNC_CTRL_SWITCH,
PS_HHO_ASYNC_CTRL_SWITCH,
IUR_HHO_ASYNC_CTRL_SWITCH,
F2P_DATATRANS_OPTIMIZE_SWITCH,
IRATHO_HOCANCEL_RL_REEST_SWITCH,
TRB_RESET_RL_REEST_SWITCH,
RB_REL_RL_REEST_SWITCH,
RB_SETUP_ENHANCE_RL_REEST_SWITCH,
RAB_SETUPMOD_CNT_FIX_SWITCH,
PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH,
FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH,
UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH,
PHYCHRECFG_ENH_RL_REEST_SWITCH,
RBRECFG_ENH_RL_REEST_SWITCH,
SMC_STOP_RLC_SWITCH,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH,
CMP_IU_QOS_GTP_PDU_SN_SWITCH,
DL_TRB_RESET_BUFF_SWITCH,
RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH,
RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH
Default Value:
PS_F2D_OVERLAP_CELLUPT_SWITCH:0,AMR_HHO_FAI
L_ROLLBACK_SWITCH:0,PHY_RECFG_REEST_SWITCH:
0,IUR_RL_REEST_SWITCH:0,RB_SETUP_RL_REEST_SWI
TCH:0,RRC_CONN_SETUP_OPT_SWITCH:0,TCP_ACK_AC
CELERATOR_SWITCH:0,RRC_CELLFACH_TRB_RESET_T
O_F2D_SWITCH:0,SEND_MSG_NULL_SWITCH:0,FD_PCH
_IUR_CS_OPT_SWITCH:0,CELLUPT_T314_T315_TIMEOU
T_OPT_SWITCH:0,CS_HHO_ASYNC_CTRL_SWITCH:0,PS_
HHO_ASYNC_CTRL_SWITCH:0,IUR_HHO_ASYNC_CTRL
_SWITCH:0,F2P_DATATRANS_OPTIMIZE_SWITCH:0,IRAT
HO_HOCANCEL_RL_REEST_SWITCH:0,TRB_RESET_RL_

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

REEST_SWITCH:0,RB_REL_RL_REEST_SWITCH:0,RB_SE
TUP_ENHANCE_RL_REEST_SWITCH:0,RAB_SETUPMOD
_CNT_FIX_SWITCH:0,PCH_UE_RLC_UNRECOVERABLEE
RROR_SWITCH:0,FAST_RETURN_LTE_BY_CELL_SELEC
T_SWITCH:0,UL_DUAL_MODE_UE_D2P_OR_D2I_SWITC
H:0,PHYCHRECFG_ENH_RL_REEST_SWITCH:0,RBRECFG
_ENH_RL_REEST_SWITCH:0,SMC_STOP_RLC_SWITCH:1,
GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH:1,CMP
_IU_QOS_GTP_PDU_SN_SWITCH:0,DL_TRB_RESET_BUF
F_SWITCH:0,RRC_CELLFACH_DL_TRB_RESET_TO_F2D_
SWITCH:0,RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH:1
SoftFa
ilD2F
Switc
h

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Whether to trigger state transitions from CELL_DCH


to CELL_FACH (D2F for short) if soft handover-based service
admission fails. When this parameter is set to ON, failures in soft
handover-based service admission trigger D2F transitions for
R99 non-real-time PS services if the signal quality of the target
cell is greater than the sum of the signal quality of the best cell
plus the "SoftFailD2FOffset" parameter value. When this
parameter is set to OFF, D2F transitions are not triggered.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

SoftFa
ilD2F
Switc
h

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Whether to trigger state transitions from CELL_DCH


to CELL_FACH (D2F for short) if soft handover-based service
admission fails. When this parameter is set to ON, failures in soft
handover-based service admission trigger D2F transitions for
R99 non-real-time PS services if the signal quality of the target
cell is greater than the sum of the signal quality of the best cell
plus the "SoftFailD2FOffset" parameter value. When this
parameter is set to OFF, D2F transitions are not triggered.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

SoftFa B SET W
ilD2F S UINT RF
Offset C RAF D6 REQ 02
9 HO
02
0
02
0

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Signal quality offset of the target cell relative to the


best cell when a D2F transition is triggered due to a failure in
soft handover-based service admission. Only when the signal
quality of the target cell is greater than the sum of the signal
quality of the best cell plus this parameter value, a D2F transition
can be triggered if soft handover-based service admission fails.
GUI Value Range: -29~29
Unit: 0.5dB
Actual Value Range: -14.5~14.5
Default Value: 4

SoftFa B SET W
ilD2F S UINT RF
Offset C RAF D6 REQ 02
9 HO
02
1
02
0

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Signal quality offset of the target cell relative to the


best cell when a D2F transition is triggered due to a failure in
soft handover-based service admission. Only when the signal
quality of the target cell is greater than the sum of the signal
quality of the best cell plus this parameter value, a D2F transition
can be triggered if soft handover-based service admission fails.
GUI Value Range: -29~29
Unit: 0.5dB
Actual Value Range: -14.5~14.5
Default Value: 4

SoftFa
ilF2D
Punish
Timer

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Timer during which F2D transitions are forbidden after


a D2F transition is triggered due to a failure in soft handoverbased service admission.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 10

SoftFa
ilF2D
Punish
Timer

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov

Meaning: Timer during which F2D transitions are forbidden after


a D2F transition is triggered due to a failure in soft handoverbased service admission.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er

Default Value: 10

SoftFa
ilE2D
Switc
h

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Whether to allow for channel switching from the EDCH to the DCH (E2D for short) after an HSUPA UE
experiences a soft handover failure. If this parameter is set to
ON, E2D is allowed when a soft handover fails due to uplink
admission failures. Otherwise, E2D is not allowed when a soft
handover fails.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

SoftFa
ilE2D
Switc
h

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Whether to allow for channel switching from the EDCH to the DCH (E2D for short) after an HSUPA UE
experiences a soft handover failure. If this parameter is set to
ON, E2D is allowed when a soft handover fails due to uplink
admission failures. Otherwise, E2D is not allowed when a soft
handover fails.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

HoSw B SET
itch1 S UCO
C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D15
02
01
W
RF
D15
02
16
W
RF

Ma
cro
&
Mic
ro
Cocarr
ier
Upl
ink
Inte
rfer
enc
e

Meaning: 1.
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH:
Switch for controlling the sub-feature Macro & Micro Joint
Inter-frequency Handover. When this switch is turned on, the
feature is activated. When this switch is turned off, the feature is
deactivated. This feature checks whether UEs are located in
problem areas of intra-frequency networks with macro and micro
cells. Then, the feature instructs these UEs to move to other cells
through blind inter-frequency handovers. 2.
HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH:
This switch specifies whether handover and redirection from
UMTS to LTE are allowed. When this switch is turned on,
redirection from UMTS to LTE is allowed but handover is
prohibited. During the redirection procedure, the LTE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
03
03
W
RF
D01
06
10
06
W
RF
D15
02
17
W
RF
D15
02
01
02
W
RF
D15
02
20
W
RF
D15
02
19
W
RF

Con
trol
Loa
d
Bas
ed
PS
Red
irec
tion
fro
m
UM
TS
to
LTE
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt

Description

frequencies configured by using the "ADD


UCELLNFREQPRIOINFO" command are used for the
redirection, and the RNC does not consider whether the best cell
is configured with neighboring LTE cells. When this switch is
turned off, both redirection and handover from UMTS to LTE
are allowed. The LTE frequencies configured by using the "ADD
ULTENCELL" command are used for the redirection and
handover. 3. HO_U2L_COV_PS_HO_SWITCH: Specifies
whether to enable a coverage-based UMTS-to-LTE PS handover.
When the switch is turned on, the RNC allows the coveragebased UMTS-to-LTE PS handover procedure. When the switch
is turned off, the RNC does not allow the coverage-based
UMTS-to-LTE PS handover procedure. 4.
HO_U2L_COV_PS_REDIRECT_SWITCH: Specifies whether
to enable a coverage-based UMTS-to-LTE PS redirection. When
the switch is turned on, the RNC allows the coverage-based
UMTS-to-LTE PS redirection procedure. When the switch is
turned off, the RNC does not allow the coverage-based UMTSto-LTE PS redirection procedure. 5.
HO_INTER_RAT_PENALTY_FOR_UNCFG_SWITCH: This
parameter allows the inter-RAT handover failure caused by UE
incompatibility for only once in a call. When the switch is turned
on and a UE failed in handover from the universal terrestrial
radio access network (UTRAN) to the GSM/EDGE radio access
network (GERAN) or evolved UMTS terrestrial radio access
network (E-UTRAN) due to the cause of configuration
unacceptable, the RNC prevents the handover from UTRAN to
GERAN or E-UTRAN in this call. When the switch is turned off,
the RNC allows another handover from UTRAN to GERAN or
E-UTRAN in this call. 6.
HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH:
Whether the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing CS services. When this switch
is turned on, the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing CS services. The inter-RAT
measurement control carries the periodic intra-frequency
measurement ID so that the UEs report both the inter-RAT MRs

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D01
06
12
04
W
RF
D02
01
29
W
RF
D14
02
18
W
RF
D02
03
05
W
RF
D02
03
06

Loa
d
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
Ma
cro
&
Mic
ro
Join
t
Inte
rfreq
uen
cy
Han
dov
er
Cov
erag
e
Bas
ed
PS
Han
dov
er
fro

Description

and Ec/N0 of the active set. In this way, the RNC can decide
whether to perform an inter-RAT handover based on the Ec/N0
of the active set. When this switch is turned off, the RNC sends
only the periodic inter-RAT measurement control to UEs
processing CS services and the Ec/N0 of the active set is not
considered in the inter-RAT handovers. 7.
HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH:
Whether the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing PS services. When this switch
is turned on, the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing PS services. The inter-RAT
measurement control carries the periodic intra-frequency
measurement ID so that the UEs report both the inter-RAT MRs
and Ec/N0 of the active set. In this way, the RNC can decide
whether to perform an inter-RAT handover based on the Ec/N0
of the active set. When this switch is turned off, the RNC sends
only the periodic inter-RAT measurement control to UEs
processing PS services and the Ec/N0 of the active set is not
considered in the inter-RAT handovers. 8.
HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH:
Whether to use the algorithm of intra-frequency neighboring cell
combination. When this switch is turned on, the algorithm of
intra-frequency neighboring cell combination is used for intrafrequency measurement objects. When this switch is turned off,
the best cell algorithm is used. 9.
HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH:
Whether to use the algorithm of inter-frequency neighboring cell
combination. When this switch is turned on, the algorithm of
inter-frequency neighboring cell combination is used for interfrequency measurement objects. When this switch is turned off,
the best cell algorithm is used. 10.
HO_MC_GSM_NCELL_COMBINE_SWITCH: Whether to use
the algorithm of neighboring GSM cell combination. When this
switch is turned on, the algorithm of neighboring GSM cell
combination is used for GSM measurement objects. When this
switch is turned off, the best cell algorithm is used. 11.
HO_MC_LTE_NCELL_COMBINE_SWITCH: Whether to use

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
m
UM
TS
to
LTE
Cov
erag
e
Bas
ed
PS
Red
irec
tion
fro
m
UM
TS
to
LTE
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
PS
Ser
vice
Red
irec
tion
fro
m
UM

Description

the algorithm of neighboring LTE cell combination. When this


switch is turned on, the algorithm of neighboring LTE cell
combination is used for LTE measurement objects. When this
switch is turned off, the best cell algorithm is used. 12.
HO_U2L_LOAD_PS_HO_SWITCH: Whether a load-based PS
handover from UMTS to LTE is allowed. When this switch is
turned on, an LDR-triggered PS handover from UMTS to LTE is
allowed. 13. HO_U2L_LOAD_PS_REDIRECT_SWITCH:
Whether a load-based PS redirection from UMTS to LTE is
allowed. When this switch is turned on, an LDR-triggered PS
redirection from UMTS to LTE is allowed. When both
"HO_U2L_LOAD_PS_REDIRECT_SWITCH" and
"HO_U2L_LOAD_PS_HO_SWITCH" are turned on, a PS
handover from UMTS to LTE is preferred. 14.
HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH:Swit
ch controlling the enhanced algorithm of adding intra-frequency
neighboring cells in detected sets to active sets. When this switch
is turned on and event 1A/C/D contains information about the
best cell's intra-frequency neighboring cells that are included in
the detected set (hereinafter referred to as target cells), the RNC
searches for the target cells in the following scopes: (1)The best
cell's intra-frequency neighboring cells (assuming that these
neighboring cells are in cell group A). (2)Intra-frequency
neighboring cells of cells in the active set (assuming that these
neighboring cells are in cell group B)If the target cells are not
found, the RNC searches for them in intra-frequency
neighboring cells of cells in cell group A (assuming that these
neighboring cells are in cell group C). Upon locating the target
cells, the RNC updates the active set and includes the target cells'
information in the active set. When this switch is turned off and
event 1A/C/D contains information about the best cell's intrafrequency neighboring cells that are included in the detected set
(hereinafter referred to as target cells), the RNC determines
whether the target cells are Intra-frequency neighboring cells of
cells in the active set. If so, the RNC updates the active set and
includes the target cells' information in the active set. If not, the
RNC does not include the target cells' information in the active
set. 15.
HO_INTRA_DETSET_DRNC_CELL_INTO_ACTSET:Switch

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
TS
to
LTE
Ser
vice
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed

Description

controlling the algorithm of adding intra-frequency neighboring


DRNC cells in detected sets to active sets. When event 1A/C/D
contains information about the best cell's intra-frequency
neighboring cells that are included in the detected set
(hereinafter referred to as target cells), the RNC searches for the
target cells in the following scopes: (1)The best cell's intrafrequency neighboring cells (assuming that these neighboring
cells are in cell group A). (2)Intra-frequency neighboring cells of
cells in the active set (assuming that these neighboring cells are
in cell group B). If the target cells are not found, the RNC checks
whether this switch is turned on. If so, the RNC searches for the
target cells in intra-frequency neighboring cells of cells in cell
group A (assuming that these neighboring cells are in cell group
C). If a DRNC cell is found to be the only target cell, the RNC
includes information about this cell in the active set. If not, the
RNC searches for the target cells in cell group C. If a DRNC cell
is found to be the only target cell, the RNC does not include
information about this cell in the active set. 16.
HO_1A_OR_1C_TRIG_SERV_CELL_CHG_SWITCH:Whethe
r to trigger an HSPA serving cell change after a soft handover
initiated due to the reporting of event 1A or 1C is complete.
When this switch is turned on, an HSPA serving cell change is
triggered after a soft handover initiated due to the reporting of
event 1A or 1C is complete. When this switch is turned off, an
HSPA serving cell change is not triggered after a soft handover
initiated due to the reporting of event 1A or 1C is complete. 17.
HO_1D_TRIG_SERV_CELL_CHG_JUDGE_SWITCH:Whethe
r to trigger an HSPA serving cell change upon the false reporting
of event 1D. The false reporting of event 1D indicates that there
is another cell whose signal quality is better than the signal
quality of the best cell indicated in event 1D. When this switch is
turned on, an HSPA serving cell change is triggered upon the
false reporting of event 1D. When this switch is turned off, an
HSPA serving cell change is not triggered upon the false
reporting of event 1D. 18. HO_SPID_MM_SWITCH: Whether
the RNC performs mobility management based on the SPID. 19.
HO_SRV_CELL_CHG_1D_RSCP_SWITCH: Whether to
trigger a serving cell change upon the reporting of RSCP-based
event 1D. When this switch is turned on, a serving cell change is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on triggered upon the reporting of RSCP-based event 1D. When this


Loa switch is turned off, a serving cell change is triggered upon the
d
reporting of Ec/No-based event 1D. 20.
HO_IUR_U2L_REDIR_SWITCH: Whether the RNC can
initiate an inter-RNC UMTS-to-LTE redirection. When this
switch is turned on, the RNC can initiate an inter-RNC UMTSto-LTE redirection. When this switch is turned off, the RNC
cannot initiate an inter-RNC UMTS-to-LTE redirection. 21.
HO_IUR_U2L_FAST_RETURN_SWITCH: Whether to allow
UMTS-to-LTE Fast Return if the best cell for a UE is controlled
by the DRNC. When this switch is turned on. In this case,
UMTS-to-LTE Fast Return is allowed and the SRNC adds
neighboring LTE cell EARFCNs of the best cell to the RRC
Connection Release message. When this switch is turned off. In
this case, UMTS-to-LTE Fast Return is forbidden. This switch is
effective only when the
HO_UMTS_TO_LTE_FAST_RETURN_SWITCH switch of the
"HoSwitch" parameter is turned on in the "SET
UCORRMALGOSWITCH" command. 22.
HO_LTE_SERVICE_NEED_RSCP_SWITCH: Whether the
corresponding algorithm can be used to judge signal quality of
the LTE cell preliminarily according to the RSCP of the best cell
before service-based UMTS-to-LTE handovers or redirections.
When this switch is set to on, the algorithm takes effect and the
RNC sends an intra-frequency measurement control message to
the UE to measure RSCP of the best cell. If RSCP reported by
the UE is lower than "U2LNCovRscpThd", the LTE coverage is
regarded poor and UMTS-to-LTE handovers or redirections are
prohibited. When this switch is set to off, the algorithm does not
take effect. 23.
HO_GSMNCELL_OPGRP_CARRY_OVER_IUR_SWITCH:
Whether the RNC considers information about neighboring
GSM cells indicated by proprietary IEs carried in Iur interface
messages when initiating inter-RAT handovers. When this switch
is set to on, the DRNC sends the information about GSM
operator groups and cell types to the SRNC through proprietary
IEs carried in the Radio Link Setup Response or Radio Link
Addition Response message. Upon reception of this information,
the SRNC selects appropriate neighboring GSM cells as the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

target cells for inter-RAT handovers. When this switch is set to


off, the DRNC does not send the information about neighboring
GSM cells to the SRNC and the SRNC does not consider the
preceding information when initiating inter-RAT handovers. 24.
HO_INTER_RAT_DRNC_GSMNCELL_FILTER_SWITCH:
Whether the SRNC filters neighboring GSM cells of DRNC cells
in the active set based on UE's HPLMN. When this switch is set
to on, the SRNC compares the proprietary IE "PLMN Identity"
of a neighboring GSM cell in the Radio Link Setup Response or
Radio Link Addition Response message with the HPLMN of the
UE. If they are the same, the SRNC initiates an inter-RAT
handover to the neighboring GSM cell. If not, the inter-RAT
handover cannot be initiated. When this switch is set to off, the
SRNC does not perform the preceding filtering.
GUI Value Range:
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH,
HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH,
HO_U2L_COV_PS_REDIRECT_SWITCH,
HO_U2L_COV_PS_HO_SWITCH,
HO_INTER_RAT_PENALTY_FOR_UNCFG_SWITCH,
HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH,
HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH,
HO_MC_GSM_NCELL_COMBINE_SWITCH,
HO_MC_LTE_NCELL_COMBINE_SWITCH,
HO_U2L_LOAD_PS_HO_SWITCH,
HO_U2L_LOAD_PS_REDIRECT_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH,
HO_INTRA_DETSET_DRNC_CELL_INTO_ACTSET,
HO_1A_OR_1C_TRIG_SERV_CELL_CHG_SWITCH,
HO_1D_TRIG_SERV_CELL_CHG_JUDGE_SWITCH,
HO_SPID_MM_SWITCH,
HO_SRV_CELL_CHG_1D_RSCP_SWITCH,
HO_IUR_U2L_REDIR_SWITCH,
HO_IUR_U2L_FAST_RETURN_SWITCH,
HO_LTE_SERVICE_NEED_RSCP_SWITCH,
HO_GSMNCELL_OPGRP_CARRY_OVER_IUR_SWITCH,
HO_INTER_RAT_DRNC_GSMNCELL_FILTER_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Unit: None
Actual Value Range:
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH,
HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH,
HO_U2L_COV_PS_REDIRECT_SWITCH,
HO_U2L_COV_PS_HO_SWITCH,
HO_INTER_RAT_PENALTY_FOR_UNCFG_SWITCH,
HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH,
HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH,
HO_MC_GSM_NCELL_COMBINE_SWITCH,
HO_MC_LTE_NCELL_COMBINE_SWITCH,
HO_U2L_LOAD_PS_HO_SWITCH,
HO_U2L_LOAD_PS_REDIRECT_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH,
HO_INTRA_DETSET_DRNC_CELL_INTO_ACTSET,
HO_1A_OR_1C_TRIG_SERV_CELL_CHG_SWITCH,
HO_1D_TRIG_SERV_CELL_CHG_JUDGE_SWITCH,
HO_SPID_MM_SWITCH,
HO_SRV_CELL_CHG_1D_RSCP_SWITCH,
HO_IUR_U2L_REDIR_SWITCH,
HO_IUR_U2L_FAST_RETURN_SWITCH,
HO_LTE_SERVICE_NEED_RSCP_SWITCH,
HO_GSMNCELL_OPGRP_CARRY_OVER_IUR_SWITCH,
HO_INTER_RAT_DRNC_GSMNCELL_FILTER_SWITCH
Default Value:
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH:0,HO
_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH:0,HO_
U2L_COV_PS_REDIRECT_SWITCH:0,HO_U2L_COV_PS_H
O_SWITCH:0,HO_INTER_RAT_PENALTY_FOR_UNCFG_S
WITCH:0,HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SW
ITCH:0,HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWIT
CH:0,HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH:1
,HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH:1,HO_
MC_GSM_NCELL_COMBINE_SWITCH:1,HO_MC_LTE_NC
ELL_COMBINE_SWITCH:1,HO_U2L_LOAD_PS_HO_SWIT
CH:0,HO_U2L_LOAD_PS_REDIRECT_SWITCH:0,HO_INTR
A_FREQ_DETSET_INTO_ACTSET_OPTSWH:0,HO_INTRA

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

_DETSET_DRNC_CELL_INTO_ACTSET:0,HO_1A_OR_1C_
TRIG_SERV_CELL_CHG_SWITCH:0,HO_1D_TRIG_SERV_
CELL_CHG_JUDGE_SWITCH:0,HO_SPID_MM_SWITCH:0,
HO_SRV_CELL_CHG_1D_RSCP_SWITCH:0,HO_IUR_U2L_
REDIR_SWITCH:1,HO_IUR_U2L_FAST_RETURN_SWITCH
:0,HO_LTE_SERVICE_NEED_RSCP_SWITCH:0,HO_GSMN
CELL_OPGRP_CARRY_OVER_IUR_SWITCH:0,HO_INTER
_RAT_DRNC_GSMNCELL_FILTER_SWITCH:0
HoSw B SET
itch1 S UCO
C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D15
02
01
W
RF
D15
02
16
W
RF
D02
03
03
W
RF
D01
06
10
06
W
RF
D15
02

Ma
cro
&
Mic
ro
Cocarr
ier
Upl
ink
Inte
rfer
enc
e
Con
trol
Loa
d
Bas
ed
PS
Red
irec
tion
fro
m
UM
TS
to
LTE

Meaning: 1.
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH:
Switch for controlling the sub-feature Macro & Micro Joint
Inter-frequency Handover. When this switch is turned on, the
feature is activated. When this switch is turned off, the feature is
deactivated. This feature checks whether UEs are located in
problem areas of intra-frequency networks with macro and micro
cells. Then, the feature instructs these UEs to move to other cells
through blind inter-frequency handovers. 2.
HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH:
This switch specifies whether handover and redirection from
UMTS to LTE are allowed. When this switch is turned on,
redirection from UMTS to LTE is allowed but handover is
prohibited. During the redirection procedure, the LTE
frequencies configured by using the "ADD
UCELLNFREQPRIOINFO" command are used for the
redirection, and the RNC does not consider whether the best cell
is configured with neighboring LTE cells. When this switch is
turned off, both redirection and handover from UMTS to LTE
are allowed. The LTE frequencies configured by using the "ADD
ULTENCELL" command are used for the redirection and
handover. 3. HO_U2L_COV_PS_HO_SWITCH: Specifies
whether to enable a coverage-based UMTS-to-LTE PS handover.
When the switch is turned on, the RNC allows the coveragebased UMTS-to-LTE PS handover procedure. When the switch
is turned off, the RNC does not allow the coverage-based
UMTS-to-LTE PS handover procedure. 4.
HO_U2L_COV_PS_REDIRECT_SWITCH: Specifies whether
to enable a coverage-based UMTS-to-LTE PS redirection. When
the switch is turned on, the RNC allows the coverage-based

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
17
W
RF
D15
02
01
02
W
RF
D15
02
20
W
RF
D15
02
19
W
RF
D01
06
12
04
W
RF
D02
01
29
W
RF
D14
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Loa
d
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
Ma
cro

Description

UMTS-to-LTE PS redirection procedure. When the switch is


turned off, the RNC does not allow the coverage-based UMTSto-LTE PS redirection procedure. 5.
HO_INTER_RAT_PENALTY_FOR_UNCFG_SWITCH: This
parameter allows the inter-RAT handover failure caused by UE
incompatibility for only once in a call. When the switch is turned
on and a UE failed in handover from the universal terrestrial
radio access network (UTRAN) to the GSM/EDGE radio access
network (GERAN) or evolved UMTS terrestrial radio access
network (E-UTRAN) due to the cause of configuration
unacceptable, the RNC prevents the handover from UTRAN to
GERAN or E-UTRAN in this call. When the switch is turned off,
the RNC allows another handover from UTRAN to GERAN or
E-UTRAN in this call. 6.
HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH:
Whether the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing CS services. When this switch
is turned on, the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing CS services. The inter-RAT
measurement control carries the periodic intra-frequency
measurement ID so that the UEs report both the inter-RAT MRs
and Ec/N0 of the active set. In this way, the RNC can decide
whether to perform an inter-RAT handover based on the Ec/N0
of the active set. When this switch is turned off, the RNC sends
only the periodic inter-RAT measurement control to UEs
processing CS services and the Ec/N0 of the active set is not
considered in the inter-RAT handovers. 7.
HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH:
Whether the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing PS services. When this switch
is turned on, the RNC sends the periodic inter-RAT measurement
control and periodic intra-frequency measurement control
simultaneously to UEs processing PS services. The inter-RAT
measurement control carries the periodic intra-frequency
measurement ID so that the UEs report both the inter-RAT MRs
and Ec/N0 of the active set. In this way, the RNC can decide

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
18
W
RF
D02
03
05
W
RF
D02
03
06

&
Mic
ro
Join
t
Inte
rfreq
uen
cy
Han
dov
er
Cov
erag
e
Bas
ed
PS
Han
dov
er
fro
m
UM
TS
to
LTE
Cov
erag
e
Bas
ed
PS
Red
irec
tion
fro
m

Description

whether to perform an inter-RAT handover based on the Ec/N0


of the active set. When this switch is turned off, the RNC sends
only the periodic inter-RAT measurement control to UEs
processing PS services and the Ec/N0 of the active set is not
considered in the inter-RAT handovers. 8.
HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH:
Whether to use the algorithm of intra-frequency neighboring cell
combination. When this switch is turned on, the algorithm of
intra-frequency neighboring cell combination is used for intrafrequency measurement objects. When this switch is turned off,
the best cell algorithm is used. 9.
HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH:
Whether to use the algorithm of inter-frequency neighboring cell
combination. When this switch is turned on, the algorithm of
inter-frequency neighboring cell combination is used for interfrequency measurement objects. When this switch is turned off,
the best cell algorithm is used. 10.
HO_MC_GSM_NCELL_COMBINE_SWITCH: Whether to use
the algorithm of neighboring GSM cell combination. When this
switch is turned on, the algorithm of neighboring GSM cell
combination is used for GSM measurement objects. When this
switch is turned off, the best cell algorithm is used. 11.
HO_MC_LTE_NCELL_COMBINE_SWITCH: Whether to use
the algorithm of neighboring LTE cell combination. When this
switch is turned on, the algorithm of neighboring LTE cell
combination is used for LTE measurement objects. When this
switch is turned off, the best cell algorithm is used. 12.
HO_U2L_LOAD_PS_HO_SWITCH: Whether a load-based PS
handover from UMTS to LTE is allowed. When this switch is
turned on, an LDR-triggered PS handover from UMTS to LTE is
allowed. 13. HO_U2L_LOAD_PS_REDIRECT_SWITCH:
Whether a load-based PS redirection from UMTS to LTE is
allowed. When this switch is turned on, an LDR-triggered PS
redirection from UMTS to LTE is allowed. When both
"HO_U2L_LOAD_PS_REDIRECT_SWITCH" and
"HO_U2L_LOAD_PS_HO_SWITCH" are turned on, a PS
handover from UMTS to LTE is preferred. 14.
HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH:Swit
ch controlling the enhanced algorithm of adding intra-frequency

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UM
TS
to
LTE
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to
LTE
Ser
vice
Bas
ed
PS
Han
dov
er
fro
m
UM
TS

Description

neighboring cells in detected sets to active sets. When this switch


is turned on and event 1A/C/D contains information about the
best cell's intra-frequency neighboring cells that are included in
the detected set (hereinafter referred to as target cells), the RNC
searches for the target cells in the following scopes: (1)The best
cell's intra-frequency neighboring cells (assuming that these
neighboring cells are in cell group A). (2)Intra-frequency
neighboring cells of cells in the active set (assuming that these
neighboring cells are in cell group B)If the target cells are not
found, the RNC searches for them in intra-frequency
neighboring cells of cells in cell group A (assuming that these
neighboring cells are in cell group C). Upon locating the target
cells, the RNC updates the active set and includes the target cells'
information in the active set. When this switch is turned off and
event 1A/C/D contains information about the best cell's intrafrequency neighboring cells that are included in the detected set
(hereinafter referred to as target cells), the RNC determines
whether the target cells are Intra-frequency neighboring cells of
cells in the active set. If so, the RNC updates the active set and
includes the target cells' information in the active set. If not, the
RNC does not include the target cells' information in the active
set. 15.
HO_INTRA_DETSET_DRNC_CELL_INTO_ACTSET:Switch
controlling the algorithm of adding intra-frequency neighboring
DRNC cells in detected sets to active sets. When event 1A/C/D
contains information about the best cell's intra-frequency
neighboring cells that are included in the detected set
(hereinafter referred to as target cells), the RNC searches for the
target cells in the following scopes: (1)The best cell's intrafrequency neighboring cells (assuming that these neighboring
cells are in cell group A). (2)Intra-frequency neighboring cells of
cells in the active set (assuming that these neighboring cells are
in cell group B). If the target cells are not found, the RNC checks
whether this switch is turned on. If so, the RNC searches for the
target cells in intra-frequency neighboring cells of cells in cell
group A (assuming that these neighboring cells are in cell group
C). If a DRNC cell is found to be the only target cell, the RNC
includes information about this cell in the active set. If not, the
RNC searches for the target cells in cell group C. If a DRNC cell

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
to
LTE
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Description

is found to be the only target cell, the RNC does not include
information about this cell in the active set. 16.
HO_1A_OR_1C_TRIG_SERV_CELL_CHG_SWITCH:Whethe
r to trigger an HSPA serving cell change after a soft handover
initiated due to the reporting of event 1A or 1C is complete.
When this switch is turned on, an HSPA serving cell change is
triggered after a soft handover initiated due to the reporting of
event 1A or 1C is complete. When this switch is turned off, an
HSPA serving cell change is not triggered after a soft handover
initiated due to the reporting of event 1A or 1C is complete. 17.
HO_1D_TRIG_SERV_CELL_CHG_JUDGE_SWITCH:Whethe
r to trigger an HSPA serving cell change upon the false reporting
of event 1D. The false reporting of event 1D indicates that there
is another cell whose signal quality is better than the signal
quality of the best cell indicated in event 1D. When this switch is
turned on, an HSPA serving cell change is triggered upon the
false reporting of event 1D. When this switch is turned off, an
HSPA serving cell change is not triggered upon the false
reporting of event 1D. 18. HO_SPID_MM_SWITCH: Whether
the RNC performs mobility management based on the SPID. 19.
HO_SRV_CELL_CHG_1D_RSCP_SWITCH: Whether to
trigger a serving cell change upon the reporting of RSCP-based
event 1D. When this switch is turned on, a serving cell change is
triggered upon the reporting of RSCP-based event 1D. When this
switch is turned off, a serving cell change is triggered upon the
reporting of Ec/No-based event 1D. 20.
HO_IUR_U2L_REDIR_SWITCH: Whether the RNC can
initiate an inter-RNC UMTS-to-LTE redirection. When this
switch is turned on, the RNC can initiate an inter-RNC UMTSto-LTE redirection. When this switch is turned off, the RNC
cannot initiate an inter-RNC UMTS-to-LTE redirection. 21.
HO_IUR_U2L_FAST_RETURN_SWITCH: Whether to allow
UMTS-to-LTE Fast Return if the best cell for a UE is controlled
by the DRNC. When this switch is turned on. In this case,
UMTS-to-LTE Fast Return is allowed and the SRNC adds
neighboring LTE cell EARFCNs of the best cell to the RRC
Connection Release message. When this switch is turned off. In
this case, UMTS-to-LTE Fast Return is forbidden. This switch is
effective only when the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

HO_UMTS_TO_LTE_FAST_RETURN_SWITCH switch of the


"HoSwitch" parameter is turned on in the "SET
UCORRMALGOSWITCH" command. 22.
HO_LTE_SERVICE_NEED_RSCP_SWITCH: Whether the
corresponding algorithm can be used to judge signal quality of
the LTE cell preliminarily according to the RSCP of the best cell
before service-based UMTS-to-LTE handovers or redirections.
When this switch is set to on, the algorithm takes effect and the
RNC sends an intra-frequency measurement control message to
the UE to measure RSCP of the best cell. If RSCP reported by
the UE is lower than "U2LNCovRscpThd", the LTE coverage is
regarded poor and UMTS-to-LTE handovers or redirections are
prohibited. When this switch is set to off, the algorithm does not
take effect. 23.
HO_GSMNCELL_OPGRP_CARRY_OVER_IUR_SWITCH:
Whether the RNC considers information about neighboring
GSM cells indicated by proprietary IEs carried in Iur interface
messages when initiating inter-RAT handovers. When this switch
is set to on, the DRNC sends the information about GSM
operator groups and cell types to the SRNC through proprietary
IEs carried in the Radio Link Setup Response or Radio Link
Addition Response message. Upon reception of this information,
the SRNC selects appropriate neighboring GSM cells as the
target cells for inter-RAT handovers. When this switch is set to
off, the DRNC does not send the information about neighboring
GSM cells to the SRNC and the SRNC does not consider the
preceding information when initiating inter-RAT handovers. 24.
HO_INTER_RAT_DRNC_GSMNCELL_FILTER_SWITCH:
Whether the SRNC filters neighboring GSM cells of DRNC cells
in the active set based on UE's HPLMN. When this switch is set
to on, the SRNC compares the proprietary IE "PLMN Identity"
of a neighboring GSM cell in the Radio Link Setup Response or
Radio Link Addition Response message with the HPLMN of the
UE. If they are the same, the SRNC initiates an inter-RAT
handover to the neighboring GSM cell. If not, the inter-RAT
handover cannot be initiated. When this switch is set to off, the
SRNC does not perform the preceding filtering.
GUI Value Range:
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH,
HO_U2L_COV_PS_REDIRECT_SWITCH,
HO_U2L_COV_PS_HO_SWITCH,
HO_INTER_RAT_PENALTY_FOR_UNCFG_SWITCH,
HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH,
HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH,
HO_MC_GSM_NCELL_COMBINE_SWITCH,
HO_MC_LTE_NCELL_COMBINE_SWITCH,
HO_U2L_LOAD_PS_HO_SWITCH,
HO_U2L_LOAD_PS_REDIRECT_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH,
HO_INTRA_DETSET_DRNC_CELL_INTO_ACTSET,
HO_1A_OR_1C_TRIG_SERV_CELL_CHG_SWITCH,
HO_1D_TRIG_SERV_CELL_CHG_JUDGE_SWITCH,
HO_SPID_MM_SWITCH,
HO_SRV_CELL_CHG_1D_RSCP_SWITCH,
HO_IUR_U2L_REDIR_SWITCH,
HO_IUR_U2L_FAST_RETURN_SWITCH,
HO_LTE_SERVICE_NEED_RSCP_SWITCH,
HO_GSMNCELL_OPGRP_CARRY_OVER_IUR_SWITCH,
HO_INTER_RAT_DRNC_GSMNCELL_FILTER_SWITCH
Unit: None
Actual Value Range:
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH,
HO_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH,
HO_U2L_COV_PS_REDIRECT_SWITCH,
HO_U2L_COV_PS_HO_SWITCH,
HO_INTER_RAT_PENALTY_FOR_UNCFG_SWITCH,
HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH,
HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH,
HO_MC_GSM_NCELL_COMBINE_SWITCH,
HO_MC_LTE_NCELL_COMBINE_SWITCH,
HO_U2L_LOAD_PS_HO_SWITCH,
HO_U2L_LOAD_PS_REDIRECT_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_OPTSWH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

HO_INTRA_DETSET_DRNC_CELL_INTO_ACTSET,
HO_1A_OR_1C_TRIG_SERV_CELL_CHG_SWITCH,
HO_1D_TRIG_SERV_CELL_CHG_JUDGE_SWITCH,
HO_SPID_MM_SWITCH,
HO_SRV_CELL_CHG_1D_RSCP_SWITCH,
HO_IUR_U2L_REDIR_SWITCH,
HO_IUR_U2L_FAST_RETURN_SWITCH,
HO_LTE_SERVICE_NEED_RSCP_SWITCH,
HO_GSMNCELL_OPGRP_CARRY_OVER_IUR_SWITCH,
HO_INTER_RAT_DRNC_GSMNCELL_FILTER_SWITCH
Default Value:
HO_COMACROMICRO_INTER_FREQ_OUT_SWITCH:0,HO
_U2L_REDIR_BASED_ABSOLUTE_FREQ_SWITCH:0,HO_
U2L_COV_PS_REDIRECT_SWITCH:0,HO_U2L_COV_PS_H
O_SWITCH:0,HO_INTER_RAT_PENALTY_FOR_UNCFG_S
WITCH:0,HO_CS_IRATHHO_WITH_INTRA_FREQ_MR_SW
ITCH:0,HO_PS_IRATHHO_WITH_INTRA_FREQ_MR_SWIT
CH:0,HO_MC_INTRAFREQ_NCELL_COMBINE_SWITCH:1
,HO_MC_INTERFREQ_NCELL_COMBINE_SWITCH:1,HO_
MC_GSM_NCELL_COMBINE_SWITCH:1,HO_MC_LTE_NC
ELL_COMBINE_SWITCH:1,HO_U2L_LOAD_PS_HO_SWIT
CH:0,HO_U2L_LOAD_PS_REDIRECT_SWITCH:0,HO_INTR
A_FREQ_DETSET_INTO_ACTSET_OPTSWH:0,HO_INTRA
_DETSET_DRNC_CELL_INTO_ACTSET:0,HO_1A_OR_1C_
TRIG_SERV_CELL_CHG_SWITCH:0,HO_1D_TRIG_SERV_
CELL_CHG_JUDGE_SWITCH:0,HO_SPID_MM_SWITCH:0,
HO_SRV_CELL_CHG_1D_RSCP_SWITCH:0,HO_IUR_U2L_
REDIR_SWITCH:1,HO_IUR_U2L_FAST_RETURN_SWITCH
:0,HO_LTE_SERVICE_NEED_RSCP_SWITCH:0,HO_GSMN
CELL_OPGRP_CARRY_OVER_IUR_SWITCH:0,HO_INTER
_RAT_DRNC_GSMNCELL_FILTER_SWITCH:0
UsedI
RATH
OLow
erThd
EcNo

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er

Meaning: Lower Ec/No threshold for an intra-frequency


neighboring cell when an inter-RAT handover is to be
implemented. If the Ec/No reported by the serving cell is lower
than this threshold, an inter-RAT handover is not implemented.
Otherwise, an inter-RAT handover is implemented.
GUI Value Range: -24~0
Unit: dB

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
MOD
UCE
LLIN
TERR
ATH
OCO
V

Description

Bas Actual Value Range: -24~0


ed Default Value: -18
on
Cov
erag
e

UsedI
RATH
OLow
erThd
EcNo

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Lower Ec/No threshold for an intra-frequency


neighboring cell when an inter-RAT handover is to be
implemented. If the Ec/No reported by the serving cell is lower
than this threshold, an inter-RAT handover is not implemented.
Otherwise, an inter-RAT handover is implemented.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -18

UsedI
RATH
OUpp
erThd
EcNo

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Upper Ec/No threshold for an intra-frequency


neighboring cell when an inter-RAT handover is to be
implemented. If the Ec/No reported by the serving cell exceeds
this threshold, an inter-RAT handover is not implemented.
Otherwise, an inter-RAT handover is implemented.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: 0

UsedI B ADD

W Inte Meaning: Upper Ec/No threshold for an intra-frequency

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RATH
OUpp
erThd
EcNo

S
C
6
9
1
0

Description

UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

RF
D02
03
03

rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

neighboring cell when an inter-RAT handover is to be


implemented. If the Ec/No reported by the serving cell exceeds
this threshold, an inter-RAT handover is not implemented.
Otherwise, an inter-RAT handover is implemented.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: 0

HoSw B SET
itch
S UCO
C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D02
02
01
W
RF
D01
06
10
06
W
RF
D02
02
03
W
RF
D02
02
02

Intr
a
Nod
eB
Soft
er
Han
dov
er
HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
r
RN
C
Soft
Han

Meaning: 1. HO_ALGO_HCS_SPEED_EST_SWITCH: When


the switch is on, the RNC evaluates the UE's moving speed in
the HCS and initiates fast intra-layer or slow inter-layer
handover. 2. HO_ALGO_LDR_ALLOW_SHO_SWITCH:
When the switch is on, the LDR inter-frequency handover is
allowed during soft handover. 3.
HO_ALGO_MBMS_FLC_SWITCH: When the switch is on, the
UE requires that the redirection strategy be used for frequency
layer convergence. 4. HO_ALGO_OVERLAY_SWITCH: When
the switch is on, the associated receiving and mobility algorithms
of the overlay network are used. When the switch is not on, the
associated algorithms are not used. Overlay network is an
UTRAN network covering present network, it supports HSPA,
MBMS and other new features. To satisfy new requirements of
operator and restrictions of present network, overlay network
realizes operation distribution and load sharing between new
network and present network, also gives special handling for
mobility management of network verge. 5.
HO_INTER_FREQ_HARD_HO_SWITCH: When the switch is
on, the RNC is allowed to initiate inter-frequency measure
control or the load-based inter-frequency hard handover upon the
handover decision on inter-frequency load. 6.
HO_LTE_SERVICE_PSHO_OUT_SWITCH: Whether to enable
service-based PS handover from UMTS to LTE. When this
switch is turned on, the RNC can send LTE MEASUREMENT

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D02
03
09
W
RF
D02
01
03
W
RF
D02
01
06
W
RF
D01
06
12
04
W
RF
D02
01
29
W
RF
D07
00
06
W

dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Loa
d
Res
huff
ling
HS

Description

CONTROL message based on service and initiate service-based


PS handover from UMTS to LTE. When this switch is turned off,
the RNC cannot initiate service-based PS handover from UMTS
to LTE. 7. HO_INTER_RAT_CS_OUT_SWITCH: When the
switch is on, the RNC is allowed to initiate inter-frequency
measure control and the CS inter-RAT hard handover from the
3G network to the 2G network. 8.
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH:
When the switch is on, the NACC function is supported during
the PS inter-RAT handover from the 3G network to the 2G
network in the cell change order process. When the switch is not
on, the NACC function is not supported. When
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH is ON,
this switch is useless. When the NACC function is supported, the
UE skips the reading procedure as the SI/PSI of the target cell is
provided after the UE accesses the 2G cell. Thus, the delay of
inter-cell handover is reduced. 9.
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH: When
the switch is on, the PS inter-RAT handover from the 3G
network to the 2G network is performed in the relocation
process. When the switch is not on, the PS inter-RAT handover
from the 3G network to the 2G network is performed in the cell
change order process. 10.
HO_INTER_RAT_PS_OUT_SWITCH: When the switch is on,
the RNC is allowed to initiate inter-frequency measure control
and the PS inter-RAT hard handover from the 3G network to the
2G network. 11.
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH: When the
switch is on, the attributes of inter-RAT handover of the services
are based on the configuration of RNC parameters. When the
switch is not on, the attributes are set on the basis of the CN. If
no information is provided by the CN, the attributes are then
based on the RNC parameters. 12.
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH:
When the switch is on, the cells in the detected set from which
the RNC receives their valid event reports can be added to the
active set. The cells allowed to be added to the active set must be
the neighboring cells of the cells in the active set. 13.
HO_INTRA_FREQ_DETSET_RPRT_SWITCH: When the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D07
00
07
W
RF
D14
01
02
W
RF
D07
00
05
W
RF
D15
02
01
W
RF
D02
13
11
02
W
RF
D02
03
04
W
RF

UP
A
Mo
bilit
y
Ma
nag
eme
nt
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to
LTE
GS
M
and
UM
TS
Loa
d
Bal
anci
ng
Bas
ed
on
Iurg
GS
M
and

Description

switch is on, the intra-frequency measurement reports of the


detected set can be reported by UE. 14.
HO_INTRA_FREQ_HARD_HO_SWITCH: When the switch is
on, the RNC is allowed to initiate the intra-frequency hard
handover. 15. HO_INTRA_FREQ_RPRT_1J_SWITCH: When
the switch is on, the event 1J is included in the delivery of intrafrequency measurement control if the UE version is R6 or later
versions. 16. HO_INTRA_FREQ_SOFT_HO_SWITCH: When
this switch is turned on, the cells under the RNC support soft
handovers. Upon receiving event 1A, 1B, 1C, or 1D after
delivering an intra-frequency measurement control message to
the UE, the RNC initiates associated addition, removal, and
replacement of target cell of the soft handover. 17.
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH: When the
switch is on, the neighboring cell whose frequency band is
beyond the UE's capabilities can also be delivered in the interfrequency measurement list. 18.
HO_MC_NCELL_COMBINE_SWITCH: When the switch is
on, the neighboring cell combined algorithm is used during the
delivery of the objects to be measured. When the switch is not
on, the optimal cell algorithm is used. 19.
HO_MC_SIGNAL_IUR_INTRA_SWITCH: When the switch is
on, intra-frequency handover is allowed over the Iur interface if
the UE has only signaling. 20. HO_MC_SIGNAL_SWITCH:
When the switch is on, quality measurement on the active set is
delivered after signaling setup but before service setup. If the UE
is at the cell verge or receives weak signals after accessing the
network, the RNC can trigger inter-frequency or inter-RAT
handover when the UE sets up the RRC. 21.
HO_MC_SNA_RESTRICTION_SWITCH: When the switch is
on, the RNC controls the UEs in the connected state based on the
configurations on the CN. The UEs can only access and move in
authorized cells. 22. HO_LTE_PS_OUT_SWITCH: Whether to
enable handover from UMTS to LTE. When this switch is turned
on, the RNC can send LTE MEASUREMENT CONTROL
message and initiate PS handover or redirection from UMTS to
LTE. When this switch is turned off, the RNC cannot perform the
preceding procedures. 23.
HO_LTE_SERVICE_PS_OUT_SWITCH: Whether to enable

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
12
00
W
RF
D02
03
08
W
RF
D01
06
10
W
RF
D01
06
12
W
RF
D01
06
16
W
RF
D02
03
01
W
RF
D02

UM
TS
Traf
fic
Stee
ring
Bas
ed
on
Iurg
CS
Fall
bac
k
Gua
rant
ee
for
LTE
Em
erge
ncy
Call
s
NA
CC
Pro
ced
ure
Opt
imi
zati
on
Bas
ed
on
Iurg

Description

service-based redirection from UMTS to LTE. When this switch


is turned on, the RNC can send LTE MEASUREMENT
CONTROL message based on service and initiate service-based
PS redirection from UMTS to LTE. When this switch is turned
off, the RNC cannot initiate service-based PS redirection from
UMTS to LTE. 24. HO_H2G_SRVCC_SWITCH :This bit is a
Single Radio Voice Call Continuity (SRVCC) switch for the
VoIP service that is handed over to GERAN. SRVCC ensures the
continuity of voice services that are handed over between the CS
domain and the IP Multimedia Subsystem (IMS).The meaning of
the bit is as follows: When it is set to "ON", it indicates that the
VoIP service can be handed over to GERAN through SRVCC
procedure.When it is set to "OFF", it indicates that the VoIP
service cannot be handed over to GERAN through SRVCC
procedure. 25.
HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWITCH: This
switch controls which event to be preferentially processed when
both an intra- frequency measurement report event and event 2D
or 2F need to be processed. Turning on this switch allows the
intra-frequency measurement report event to be preferentially
processed. Turning off this switch allows event 2D or 2F to be
preferentially processed. 26. HO_CIO_1D_USED: Whether the
RNC instructs the UE to use the cell individual offset (CIO)
parameter when reporting event 1D. If this field is selected, the
RNC instructs the UE to use the CIO parameter when reporting
event 1D. If this field is not selected, the RNC does not instruct
the UE to use the CIO parameter when reporting event 1D. The
call drop rate will increase if the switch is opened when the CIO
is configured to a big value. 27.
HO_HCS_SPD_INI_BSD_UE_SWITCH: Whether the RNC
determines the initial speed state of a UE based on the
enUeMobilityStateInd information element (IE) sent by the UE.
If this switch is turned on, the initial UE speed state is
determined by this IE carried in the
RRC_RRC_CONNECT_REQ or RRC_CELL_UPDATE
message. If this switch is turned off, the RNC determines the UE
mobility state as before based on how frequently the UE sends
an event 1D measurement report. 28.
HO_L2U_EMGCALL_SWITCH: Function switch of the CS

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
03
02
W
RF
D02
03
03
W
RF
D02
03
08
02
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
03
08
01

Ma
cro
&
Mic
ro
Cocarr
ier
Upl
ink
Inte
rfer
enc
e
Con
trol
Ded
icat
ed
Nod
e
B/C
ell
for
Ope
rato
rs
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed

Description

Fallback Guarantee for LTE Emergency Calls feature. When this


switch is turned on, this feature is activated. When a UE is
making an emergency call in an LTE cell, the UE is instructed to
move to a UMTS cell and the UMTS cell preferentially
guarantees the successful access of the UE. If the UE is
processing non-real-time PS services, the channel types and
initial data rates for these services are determined by the
"NRTInitRateforL2U" parameter in the "SET UFRC" command
during service admission. If the UE is processing real-time PS
services, the original channel types and data rates of these
services are retained during service admission. When this switch
is turned off, this feature is not activated. When a UE is making
an emergency call in an LTE cell, the UE is instructed to move to
a UMTS cell but the UMTS cell does not preferentially
guarantee the successful access of the UE. If the UE is
processing PS services, the original channel types and data rates
of these services are retained during service admission. 29.
HO_UMTS_TO_LTE_FAST_RETURN_SWITCH: Whether a
UE can fast return to the LTE network after its RRC connection
is released in the UMTS network. When this switch is turned on,
the RNC carries the information about frequencies of
neighboring LTE cells in the RRC CONNECTION RELEASE
message during a call release of a UE capable of measuring the
LTE frequencies so that the UE in idle state can fast move to the
LTE network. The information about frequencies of neighboring
LTE cells is set by the "ADD UCELLNFREQPRIOINFO"
command. When this switch is turned off, the information about
frequencies of neighboring LTE cells is not carried in the RRC
CONNECTION RELEASE message. 30.
HO_HHO_WITH_INTRA_FREQ_MR_SWITCH: When this
switch is turned on, the RNC sends periodical inter-frequency
and intra-frequency measurement control messages, and includes
the information element (IE) measurementIdentiy in the interfrequency measurement control message to instruct a UE to
report signal quality in an active set cell in a periodical interfrequency measurement report. When this switch is turned off,
the RNC sends only a periodical inter-frequency measurement
control message without this IE. 31.
HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH : Whether

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
on
DL
Qo
S
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Inte
rRA
T
Han
dov
er
Pha
se 2
HS
DP
A
Intr
odu
ctio
n
Pac
kag
e
HS
UP
A
Intr
odu
ctio

Description

handover parameters dedicated to combined services are set.


When this switch is turned on, the handover parameters
dedicated to CS and PS combined services are used when CS
and PS combined services are processed. The handover
parameters dedicated to CS and PS combined services are set by
the "SET UMULTIRABHOCOV" command. When this switch
is turned off, the upper threshold for the handover parameters
between the CS and PS services is used when CS and PS
combined services are processed.
GUI Value Range: HO_ALGO_HCS_SPEED_EST_SWITCH,
HO_ALGO_LDR_ALLOW_SHO_SWITCH,
HO_ALGO_MBMS_FLC_SWITCH,
HO_ALGO_OVERLAY_SWITCH,
HO_INTER_FREQ_HARD_HO_SWITCH,
HO_LTE_SERVICE_PSHO_OUT_SWITCH,
HO_INTER_RAT_CS_OUT_SWITCH,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH,
HO_INTER_RAT_PS_OUT_SWITCH,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH,
HO_INTRA_FREQ_HARD_HO_SWITCH,
HO_INTRA_FREQ_RPRT_1J_SWITCH,
HO_INTRA_FREQ_SOFT_HO_SWITCH,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH,
HO_MC_NCELL_COMBINE_SWITCH,
HO_MC_SIGNAL_IUR_INTRA_SWITCH,
HO_MC_SIGNAL_SWITCH,
HO_MC_SNA_RESTRICTION_SWITCH,
HO_LTE_PS_OUT_SWITCH,
HO_LTE_SERVICE_PS_OUT_SWITCH,
HO_H2G_SRVCC_SWITCH,
HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWITCH,
HO_CIO_1D_USED, HO_HCS_SPD_INI_BSD_UE_SWITCH,
HO_L2U_EMGCALL_SWITCH,
HO_UMTS_TO_LTE_FAST_RETURN_SWITCH,
HO_HHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
n
Pac
kag
e
MB
MS
Intr
odu
ctio
n
Pac
kag
e
Intr
a
Fre
que
ncy
Har
d
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Description

Unit: None
Actual Value Range: HO_ALGO_HCS_SPEED_EST_SWITCH,
HO_ALGO_LDR_ALLOW_SHO_SWITCH,
HO_ALGO_MBMS_FLC_SWITCH,
HO_ALGO_OVERLAY_SWITCH,
HO_INTER_FREQ_HARD_HO_SWITCH,
HO_LTE_SERVICE_PSHO_OUT_SWITCH,
HO_INTER_RAT_CS_OUT_SWITCH,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH,
HO_INTER_RAT_PS_OUT_SWITCH,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH,
HO_INTRA_FREQ_HARD_HO_SWITCH,
HO_INTRA_FREQ_RPRT_1J_SWITCH,
HO_INTRA_FREQ_SOFT_HO_SWITCH,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH,
HO_MC_NCELL_COMBINE_SWITCH,
HO_MC_SIGNAL_IUR_INTRA_SWITCH,
HO_MC_SIGNAL_SWITCH,
HO_MC_SNA_RESTRICTION_SWITCH,
HO_LTE_PS_OUT_SWITCH,
HO_LTE_SERVICE_PS_OUT_SWITCH,
HO_H2G_SRVCC_SWITCH,
HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWITCH,
HO_CIO_1D_USED, HO_HCS_SPD_INI_BSD_UE_SWITCH,
HO_L2U_EMGCALL_SWITCH,
HO_UMTS_TO_LTE_FAST_RETURN_SWITCH,
HO_HHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH
Default Value:
HO_ALGO_HCS_SPEED_EST_SWITCH:0,HO_ALGO_LDR_
ALLOW_SHO_SWITCH:1,HO_ALGO_MBMS_FLC_SWITC
H:0,HO_ALGO_OVERLAY_SWITCH:0,HO_INTER_FREQ_
HARD_HO_SWITCH:0,HO_LTE_SERVICE_PSHO_OUT_SW
ITCH:0,HO_INTER_RAT_CS_OUT_SWITCH:1,HO_INTER_
RAT_PS_3G2G_CELLCHG_NACC_SWITCH:0,HO_INTER_
RAT_PS_3G2G_RELOCATION_SWITCH:0,HO_INTER_RAT

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
r-

Description

_PS_OUT_SWITCH:1,HO_INTER_RAT_RNC_SERVICE_HO
_SWITCH:0,HO_INTRA_FREQ_DETSET_INTO_ACTSET_S
WITCH:1,HO_INTRA_FREQ_DETSET_RPRT_SWITCH:1,H
O_INTRA_FREQ_HARD_HO_SWITCH:1,HO_INTRA_FREQ
_RPRT_1J_SWITCH:0,HO_INTRA_FREQ_SOFT_HO_SWIT
CH:1,HO_MC_MEAS_BEYOND_UE_CAP_SWITCH:0,HO_
MC_NCELL_COMBINE_SWITCH:1,HO_MC_SIGNAL_IUR_
INTRA_SWITCH:0,HO_MC_SIGNAL_SWITCH:0,HO_MC_S
NA_RESTRICTION_SWITCH:0,HO_LTE_PS_OUT_SWITCH
:0,HO_LTE_SERVICE_PS_OUT_SWITCH:0,HO_H2G_SRVC
C_SWITCH:0,HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWIT
CH:0,HO_CIO_1D_USED:0,HO_HCS_SPD_INI_BSD_UE_S
WITCH:0,HO_L2U_EMGCALL_SWITCH:0,HO_UMTS_TO_
LTE_FAST_RETURN_SWITCH:0,HO_HHO_WITH_INTRA_
FREQ_MR_SWITCH:0,HO_MULTIRAB_CSPS_HO_COV_PA
RA_SWITCH:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RA
T
Han
dov
er
Bas
ed
on
Loa
d
NA
CC(
Net
wor
k
Ass
iste
d
Cell
Cha
nge
)
HoSw B SET
itch
S UCO
C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D02
02
01
W
RF
D01
06
10
06
W
RF
D-

Intr
a
Nod
eB
Soft
er
Han
dov
er
HS
DP
A
Mo
bilit
y
Ma

Meaning: 1. HO_ALGO_HCS_SPEED_EST_SWITCH: When


the switch is on, the RNC evaluates the UE's moving speed in
the HCS and initiates fast intra-layer or slow inter-layer
handover. 2. HO_ALGO_LDR_ALLOW_SHO_SWITCH:
When the switch is on, the LDR inter-frequency handover is
allowed during soft handover. 3.
HO_ALGO_MBMS_FLC_SWITCH: When the switch is on, the
UE requires that the redirection strategy be used for frequency
layer convergence. 4. HO_ALGO_OVERLAY_SWITCH: When
the switch is on, the associated receiving and mobility algorithms
of the overlay network are used. When the switch is not on, the
associated algorithms are not used. Overlay network is an
UTRAN network covering present network, it supports HSPA,
MBMS and other new features. To satisfy new requirements of
operator and restrictions of present network, overlay network
realizes operation distribution and load sharing between new

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
02
03
W
RF
D02
02
02
W
RF
D02
03
09
W
RF
D02
01
03
W
RF
D02
01
06
W
RF
D01
06
12
04
W
RF
D02

nag
eme
nt
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Loa
d

Description

network and present network, also gives special handling for


mobility management of network verge. 5.
HO_INTER_FREQ_HARD_HO_SWITCH: When the switch is
on, the RNC is allowed to initiate inter-frequency measure
control or the load-based inter-frequency hard handover upon the
handover decision on inter-frequency load. 6.
HO_LTE_SERVICE_PSHO_OUT_SWITCH: Whether to enable
service-based PS handover from UMTS to LTE. When this
switch is turned on, the RNC can send LTE MEASUREMENT
CONTROL message based on service and initiate service-based
PS handover from UMTS to LTE. When this switch is turned off,
the RNC cannot initiate service-based PS handover from UMTS
to LTE. 7. HO_INTER_RAT_CS_OUT_SWITCH: When the
switch is on, the RNC is allowed to initiate inter-frequency
measure control and the CS inter-RAT hard handover from the
3G network to the 2G network. 8.
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH:
When the switch is on, the NACC function is supported during
the PS inter-RAT handover from the 3G network to the 2G
network in the cell change order process. When the switch is not
on, the NACC function is not supported. When
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH is ON,
this switch is useless. When the NACC function is supported, the
UE skips the reading procedure as the SI/PSI of the target cell is
provided after the UE accesses the 2G cell. Thus, the delay of
inter-cell handover is reduced. 9.
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH: When
the switch is on, the PS inter-RAT handover from the 3G
network to the 2G network is performed in the relocation
process. When the switch is not on, the PS inter-RAT handover
from the 3G network to the 2G network is performed in the cell
change order process. 10.
HO_INTER_RAT_PS_OUT_SWITCH: When the switch is on,
the RNC is allowed to initiate inter-frequency measure control
and the PS inter-RAT hard handover from the 3G network to the
2G network. 11.
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH: When the
switch is on, the attributes of inter-RAT handover of the services
are based on the configuration of RNC parameters. When the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
01
29
W
RF
D07
00
06
W
RF
D07
00
07
W
RF
D14
01
02
W
RF
D07
00
05
W
RF
D15
02
01
W
RF
D02
13
11

Bal
anc
e
Loa
d
Res
huff
ling
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to
LTE
GS
M
and
UM
TS
Loa
d
Bal
anci

Description

switch is not on, the attributes are set on the basis of the CN. If
no information is provided by the CN, the attributes are then
based on the RNC parameters. 12.
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH:
When the switch is on, the cells in the detected set from which
the RNC receives their valid event reports can be added to the
active set. The cells allowed to be added to the active set must be
the neighboring cells of the cells in the active set. 13.
HO_INTRA_FREQ_DETSET_RPRT_SWITCH: When the
switch is on, the intra-frequency measurement reports of the
detected set can be reported by UE. 14.
HO_INTRA_FREQ_HARD_HO_SWITCH: When the switch is
on, the RNC is allowed to initiate the intra-frequency hard
handover. 15. HO_INTRA_FREQ_RPRT_1J_SWITCH: When
the switch is on, the event 1J is included in the delivery of intrafrequency measurement control if the UE version is R6 or later
versions. 16. HO_INTRA_FREQ_SOFT_HO_SWITCH: When
this switch is turned on, the cells under the RNC support soft
handovers. Upon receiving event 1A, 1B, 1C, or 1D after
delivering an intra-frequency measurement control message to
the UE, the RNC initiates associated addition, removal, and
replacement of target cell of the soft handover. 17.
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH: When the
switch is on, the neighboring cell whose frequency band is
beyond the UE's capabilities can also be delivered in the interfrequency measurement list. 18.
HO_MC_NCELL_COMBINE_SWITCH: When the switch is
on, the neighboring cell combined algorithm is used during the
delivery of the objects to be measured. When the switch is not
on, the optimal cell algorithm is used. 19.
HO_MC_SIGNAL_IUR_INTRA_SWITCH: When the switch is
on, intra-frequency handover is allowed over the Iur interface if
the UE has only signaling. 20. HO_MC_SIGNAL_SWITCH:
When the switch is on, quality measurement on the active set is
delivered after signaling setup but before service setup. If the UE
is at the cell verge or receives weak signals after accessing the
network, the RNC can trigger inter-frequency or inter-RAT
handover when the UE sets up the RRC. 21.
HO_MC_SNA_RESTRICTION_SWITCH: When the switch is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
W
RF
D02
03
04
W
RF
D02
12
00
W
RF
D02
03
08
W
RF
D01
06
10
W
RF
D01
06
12
W
RF
D01
06
16
W

ng
Bas
ed
on
Iurg
GS
M
and
UM
TS
Traf
fic
Stee
ring
Bas
ed
on
Iurg
CS
Fall
bac
k
Gua
rant
ee
for
LTE
Em
erge
ncy
Call
s
NA
CC
Pro
ced
ure

Description

on, the RNC controls the UEs in the connected state based on the
configurations on the CN. The UEs can only access and move in
authorized cells. 22. HO_LTE_PS_OUT_SWITCH: Whether to
enable handover from UMTS to LTE. When this switch is turned
on, the RNC can send LTE MEASUREMENT CONTROL
message and initiate PS handover or redirection from UMTS to
LTE. When this switch is turned off, the RNC cannot perform the
preceding procedures. 23.
HO_LTE_SERVICE_PS_OUT_SWITCH: Whether to enable
service-based redirection from UMTS to LTE. When this switch
is turned on, the RNC can send LTE MEASUREMENT
CONTROL message based on service and initiate service-based
PS redirection from UMTS to LTE. When this switch is turned
off, the RNC cannot initiate service-based PS redirection from
UMTS to LTE. 24. HO_H2G_SRVCC_SWITCH :This bit is a
Single Radio Voice Call Continuity (SRVCC) switch for the
VoIP service that is handed over to GERAN. SRVCC ensures the
continuity of voice services that are handed over between the CS
domain and the IP Multimedia Subsystem (IMS).The meaning of
the bit is as follows: When it is set to "ON", it indicates that the
VoIP service can be handed over to GERAN through SRVCC
procedure.When it is set to "OFF", it indicates that the VoIP
service cannot be handed over to GERAN through SRVCC
procedure. 25.
HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWITCH: This
switch controls which event to be preferentially processed when
both an intra- frequency measurement report event and event 2D
or 2F need to be processed. Turning on this switch allows the
intra-frequency measurement report event to be preferentially
processed. Turning off this switch allows event 2D or 2F to be
preferentially processed. 26. HO_CIO_1D_USED: Whether the
RNC instructs the UE to use the cell individual offset (CIO)
parameter when reporting event 1D. If this field is selected, the
RNC instructs the UE to use the CIO parameter when reporting
event 1D. If this field is not selected, the RNC does not instruct
the UE to use the CIO parameter when reporting event 1D. The
call drop rate will increase if the switch is opened when the CIO
is configured to a big value. 27.
HO_HCS_SPD_INI_BSD_UE_SWITCH: Whether the RNC

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D02
03
01
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
08
02
W
RF
D02
03
05
W
RF
D02
03
06
W
RF

Opt
imi
zati
on
Bas
ed
on
Iurg
Ma
cro
&
Mic
ro
Cocarr
ier
Upl
ink
Inte
rfer
enc
e
Con
trol
Ded
icat
ed
Nod
e
B/C
ell
for
Ope
rato
rs
Inte
r
Fre

Description

determines the initial speed state of a UE based on the


enUeMobilityStateInd information element (IE) sent by the UE.
If this switch is turned on, the initial UE speed state is
determined by this IE carried in the
RRC_RRC_CONNECT_REQ or RRC_CELL_UPDATE
message. If this switch is turned off, the RNC determines the UE
mobility state as before based on how frequently the UE sends
an event 1D measurement report. 28.
HO_L2U_EMGCALL_SWITCH: Function switch of the CS
Fallback Guarantee for LTE Emergency Calls feature. When this
switch is turned on, this feature is activated. When a UE is
making an emergency call in an LTE cell, the UE is instructed to
move to a UMTS cell and the UMTS cell preferentially
guarantees the successful access of the UE. If the UE is
processing non-real-time PS services, the channel types and
initial data rates for these services are determined by the
"NRTInitRateforL2U" parameter in the "SET UFRC" command
during service admission. If the UE is processing real-time PS
services, the original channel types and data rates of these
services are retained during service admission. When this switch
is turned off, this feature is not activated. When a UE is making
an emergency call in an LTE cell, the UE is instructed to move to
a UMTS cell but the UMTS cell does not preferentially
guarantee the successful access of the UE. If the UE is
processing PS services, the original channel types and data rates
of these services are retained during service admission. 29.
HO_UMTS_TO_LTE_FAST_RETURN_SWITCH: Whether a
UE can fast return to the LTE network after its RRC connection
is released in the UMTS network. When this switch is turned on,
the RNC carries the information about frequencies of
neighboring LTE cells in the RRC CONNECTION RELEASE
message during a call release of a UE capable of measuring the
LTE frequencies so that the UE in idle state can fast move to the
LTE network. The information about frequencies of neighboring
LTE cells is set by the "ADD UCELLNFREQPRIOINFO"
command. When this switch is turned off, the information about
frequencies of neighboring LTE cells is not carried in the RRC
CONNECTION RELEASE message. 30.
HO_HHO_WITH_INTRA_FREQ_MR_SWITCH: When this

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
03
08
01

que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Inte
rRA
T
Han
dov
er
Pha
se 2
HS
DP
A
Intr
odu
ctio
n

Description

switch is turned on, the RNC sends periodical inter-frequency


and intra-frequency measurement control messages, and includes
the information element (IE) measurementIdentiy in the interfrequency measurement control message to instruct a UE to
report signal quality in an active set cell in a periodical interfrequency measurement report. When this switch is turned off,
the RNC sends only a periodical inter-frequency measurement
control message without this IE. 31.
HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH
(Algorithm Switch for Coverage-based Inter-frequency or interRAT Handover Parameters Dedicated to CS and PS Combined
Services): Whether handover parameters dedicated to combined
services are set. When this switch is turned on, the handover
parameters dedicated to CS and PS combined services are used
when CS and PS combined services are processed. The handover
parameters dedicated to CS and PS combined services are set by
the "SET UMULTIRABHOCOV" command. When this switch
is turned off, the upper threshold for the handover parameters
between the CS and PS services is used when CS and PS
combined services are processed.
GUI Value Range: HO_ALGO_HCS_SPEED_EST_SWITCH,
HO_ALGO_LDR_ALLOW_SHO_SWITCH,
HO_ALGO_MBMS_FLC_SWITCH,
HO_ALGO_OVERLAY_SWITCH,
HO_INTER_FREQ_HARD_HO_SWITCH,
HO_LTE_SERVICE_PSHO_OUT_SWITCH,
HO_INTER_RAT_CS_OUT_SWITCH,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH,
HO_INTER_RAT_PS_OUT_SWITCH,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH,
HO_INTRA_FREQ_HARD_HO_SWITCH,
HO_INTRA_FREQ_RPRT_1J_SWITCH,
HO_INTRA_FREQ_SOFT_HO_SWITCH,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH,
HO_MC_NCELL_COMBINE_SWITCH,
HO_MC_SIGNAL_IUR_INTRA_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Pac
kag
e
HS
UP
A
Intr
odu
ctio
n
Pac
kag
e
MB
MS
Intr
odu
ctio
n
Pac
kag
e
Intr
a
Fre
que
ncy
Har
d
Han
dov
er
Inte
r
Fre
que
ncy
Har
d

Description

HO_MC_SIGNAL_SWITCH,
HO_MC_SNA_RESTRICTION_SWITCH,
HO_LTE_PS_OUT_SWITCH,
HO_LTE_SERVICE_PS_OUT_SWITCH,
HO_H2G_SRVCC_SWITCH,
HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWITCH,
HO_CIO_1D_USED, HO_HCS_SPD_INI_BSD_UE_SWITCH,
HO_L2U_EMGCALL_SWITCH,
HO_UMTS_TO_LTE_FAST_RETURN_SWITCH,
HO_HHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH
Unit: None
Actual Value Range: HO_ALGO_HCS_SPEED_EST_SWITCH,
HO_ALGO_LDR_ALLOW_SHO_SWITCH,
HO_ALGO_MBMS_FLC_SWITCH,
HO_ALGO_OVERLAY_SWITCH,
HO_INTER_FREQ_HARD_HO_SWITCH,
HO_LTE_SERVICE_PSHO_OUT_SWITCH,
HO_INTER_RAT_CS_OUT_SWITCH,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH,
HO_INTER_RAT_PS_OUT_SWITCH,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH,
HO_INTRA_FREQ_HARD_HO_SWITCH,
HO_INTRA_FREQ_RPRT_1J_SWITCH,
HO_INTRA_FREQ_SOFT_HO_SWITCH,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH,
HO_MC_NCELL_COMBINE_SWITCH,
HO_MC_SIGNAL_IUR_INTRA_SWITCH,
HO_MC_SIGNAL_SWITCH,
HO_MC_SNA_RESTRICTION_SWITCH,
HO_LTE_PS_OUT_SWITCH,
HO_LTE_SERVICE_PS_OUT_SWITCH,
HO_H2G_SRVCC_SWITCH,
HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWITCH,
HO_CIO_1D_USED, HO_HCS_SPD_INI_BSD_UE_SWITCH,
HO_L2U_EMGCALL_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
Inte
rRA
T
Han

Description

HO_UMTS_TO_LTE_FAST_RETURN_SWITCH,
HO_HHO_WITH_INTRA_FREQ_MR_SWITCH,
HO_MULTIRAB_CSPS_HO_COV_PARA_SWITCH
Default Value:
HO_ALGO_HCS_SPEED_EST_SWITCH:0,HO_ALGO_LDR_
ALLOW_SHO_SWITCH:1,HO_ALGO_MBMS_FLC_SWITC
H:0,HO_ALGO_OVERLAY_SWITCH:0,HO_INTER_FREQ_
HARD_HO_SWITCH:0,HO_LTE_SERVICE_PSHO_OUT_SW
ITCH:0,HO_INTER_RAT_CS_OUT_SWITCH:1,HO_INTER_
RAT_PS_3G2G_CELLCHG_NACC_SWITCH:0,HO_INTER_
RAT_PS_3G2G_RELOCATION_SWITCH:0,HO_INTER_RAT
_PS_OUT_SWITCH:1,HO_INTER_RAT_RNC_SERVICE_HO
_SWITCH:0,HO_INTRA_FREQ_DETSET_INTO_ACTSET_S
WITCH:1,HO_INTRA_FREQ_DETSET_RPRT_SWITCH:1,H
O_INTRA_FREQ_HARD_HO_SWITCH:1,HO_INTRA_FREQ
_RPRT_1J_SWITCH:0,HO_INTRA_FREQ_SOFT_HO_SWIT
CH:1,HO_MC_MEAS_BEYOND_UE_CAP_SWITCH:0,HO_
MC_NCELL_COMBINE_SWITCH:1,HO_MC_SIGNAL_IUR_
INTRA_SWITCH:0,HO_MC_SIGNAL_SWITCH:0,HO_MC_S
NA_RESTRICTION_SWITCH:0,HO_LTE_PS_OUT_SWITCH
:0,HO_LTE_SERVICE_PS_OUT_SWITCH:0,HO_H2G_SRVC
C_SWITCH:0,HO_INTRA_FREQ_HIGHPRIOR_2D2F_SWIT
CH:0,HO_CIO_1D_USED:0,HO_HCS_SPD_INI_BSD_UE_S
WITCH:0,HO_L2U_EMGCALL_SWITCH:0,HO_UMTS_TO_
LTE_FAST_RETURN_SWITCH:0,HO_HHO_WITH_INTRA_
FREQ_MR_SWITCH:0,HO_MULTIRAB_CSPS_HO_COV_PA
RA_SWITCH:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
NA
CC(
Net
wor
k
Ass
iste
d
Cell
Cha
nge
)
Reser B SET
vedSw S UCO
itch0 C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D02
11
01
W

Dyn
ami
c
Cha
nnel
Con
figu

Meaning: CORRM algorithm reserved switch 0. The switch is


reserved for further change request use. Disuse statement: This
parameter is used temporarily in patch versions and will be
replaced with a new parameter in later versions. The new
parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_0_BIT1,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D02
02
03
W
RF
D02
04
00
01
W
RF
D01
06
13
W
RF
D02
14
00
W
RF
D02
07
01

rati
on
Con
trol
(DC
CC)
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
Syst
em
Dir
ect
Retr
y
AM
RWB
(Ad
apti
ve
Mul
ti
Rat
e
Wid
e
Ban
d)
Dir
ect
Sig

Description

RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
nali
ng
Con
nect
ion
Reesta
blis
hme
nt
(DS
CR)
AM
R/
WB
AM
R
Spe
ech
Rat
es
Con
trol

Description

RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Default Value: RESERVED_SWITCH_0_BIT1:0,
RESERVED_SWITCH_0_BIT2:0,
RESERVED_SWITCH_0_BIT3:0,
RESERVED_SWITCH_0_BIT4:0,
RESERVED_SWITCH_0_BIT5:0,
RESERVED_SWITCH_0_BIT6:0,
RESERVED_SWITCH_0_BIT7:0,
RESERVED_SWITCH_0_BIT8:0,
RESERVED_SWITCH_0_BIT9:0,
RESERVED_SWITCH_0_BIT10:0,
RESERVED_SWITCH_0_BIT11:0,
RESERVED_SWITCH_0_BIT12:0,
RESERVED_SWITCH_0_BIT13:0,
RESERVED_SWITCH_0_BIT14:0,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT15:0,
RESERVED_SWITCH_0_BIT16:0,
RESERVED_SWITCH_0_BIT17:0,
RESERVED_SWITCH_0_BIT18:0,
RESERVED_SWITCH_0_BIT19:0,
RESERVED_SWITCH_0_BIT20:0,
RESERVED_SWITCH_0_BIT21:0,
RESERVED_SWITCH_0_BIT22:0,
RESERVED_SWITCH_0_BIT23:0,
RESERVED_SWITCH_0_BIT24:0,
RESERVED_SWITCH_0_BIT25:0,
RESERVED_SWITCH_0_BIT26:0,
RESERVED_SWITCH_0_BIT27:0,
RESERVED_SWITCH_0_BIT28:0,
RESERVED_SWITCH_0_BIT29:0,
RESERVED_SWITCH_0_BIT30:0,
RESERVED_SWITCH_0_BIT31:0,
RESERVED_SWITCH_0_BIT32:0
Reser B SET
vedSw S UCO
itch0 C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D02
11
01
W
RF
D02
02
03
W
RF
D02
04
00
01
W

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
Inte
r
RN
C
Soft
Han
dov

Meaning: CORRM algorithm reserved switch 0. The switch is


reserved for further change request use. Disuse statement: This
parameter is used temporarily in patch versions and will be
replaced with a new parameter in later versions. The new
parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D01
06
13
W
RF
D02
14
00
W
RF
D02
07
01

er
Intr
a
Syst
em
Dir
ect
Retr
y
AM
RWB
(Ad
apti
ve
Mul
ti
Rat
e
Wid
e
Ban
d)
Dir
ect
Sig
nali
ng
Con
nect
ion
Reesta
blis
hme
nt
(DS
CR)
AM

Description

RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
R/
WB
AM
R
Spe
ech
Rat
es
Con
trol

Description

RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Default Value: RESERVED_SWITCH_0_BIT1:0,
RESERVED_SWITCH_0_BIT2:0,
RESERVED_SWITCH_0_BIT3:0,
RESERVED_SWITCH_0_BIT4:0,
RESERVED_SWITCH_0_BIT5:0,
RESERVED_SWITCH_0_BIT6:0,
RESERVED_SWITCH_0_BIT7:0,
RESERVED_SWITCH_0_BIT8:0,
RESERVED_SWITCH_0_BIT9:0,
RESERVED_SWITCH_0_BIT10:0,
RESERVED_SWITCH_0_BIT11:0,
RESERVED_SWITCH_0_BIT12:0,
RESERVED_SWITCH_0_BIT13:0,
RESERVED_SWITCH_0_BIT14:0,
RESERVED_SWITCH_0_BIT15:0,
RESERVED_SWITCH_0_BIT16:0,
RESERVED_SWITCH_0_BIT17:0,
RESERVED_SWITCH_0_BIT18:0,
RESERVED_SWITCH_0_BIT19:0,
RESERVED_SWITCH_0_BIT20:0,
RESERVED_SWITCH_0_BIT21:0,
RESERVED_SWITCH_0_BIT22:0,
RESERVED_SWITCH_0_BIT23:0,
RESERVED_SWITCH_0_BIT24:0,
RESERVED_SWITCH_0_BIT25:0,
RESERVED_SWITCH_0_BIT26:0,
RESERVED_SWITCH_0_BIT27:0,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT28:0,
RESERVED_SWITCH_0_BIT29:0,
RESERVED_SWITCH_0_BIT30:0,
RESERVED_SWITCH_0_BIT31:0,
RESERVED_SWITCH_0_BIT32:0
CmpS B SET
witch2 S UCO
C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D02
11
01
W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D15
02
07
W
RF
D01
01
01
W
RF
D-

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
4CHS
DP
A

Meaning: 1. CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH:
When the switch is set to ON, the Iu user plane (UP) version is
not decreased if the Uu data rate set and the Iu data rate set in the
static relocation container are different. Otherwise, the Iu UP
version is decreased to version 1. 2.
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH:
When the switch is set to ON, RTT dedicated measurement
adopts the extended cell mode. When the switch is set to OFF,
RTT dedicated measurement does not adopt the extended cell
mode. This parameter is used to solve the problem that some
NodeBs do not support RTT dedicated measurement adopting
the extended cell mode. 3. CMP_IUR_CMCF_SWITCH: When
the switch is set to ON, compressed mode is started by using a
RADIO LINK RECONFIGURATION COMMIT message.
When the switch is set to OFF, compressed mode is started by
using a COMPRESSED MODE COMMAND message. 4.
CMP_STTD_RL_ADD_SWITCH: When the switch is set to
ON, the transmit diversity mode information element is always
carried in the RADIO LINK SETUP REQUEST message during
radio link establishment if a cell enabled with transmit diversity
and another cell disabled with transmit diversity exist under the
same NodeB. This parameter is used to solve the problem that
transmit diversity parameters are incorrectly configured for
softer handovers because the RADIO LINK ADDITION
REQUEST message does not carry the transmit diversity mode.
5. CMP_STTD_ASU_SWITCH: When a UE is soft-handed over
from a cell enabled with transmit diversity to a cell disabled with
transmit diversity, the UE may return active set update failure. If
the switch is set to ON, the RNC resends the active set update
message to the UE after an active set update failure. If the switch
is set to OFF, the RNC does not resend an active set update
message after an active set update failure. 6.
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH: When the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
15
02
50
W
RF
D02
01
34
W
RF
D01
05
01
W
RF
D02
06
05
01
W
RF
D01
02
02
W
RF
D15
02
09
W
RF
D02

3G
PP
R9
Spe
cifi
cati
ons
3CHS
DP
A
Pus
h to
Talk
Con
vers
atio
nal
Qo
S
Cla
ss
SR
NS
Rel
ocat
ion
(UE
Not
Inv
olve
d)
UE
Stat
e in
Con
nect
ed
Mo

Description

switch is set to OFF, a penalty is imposed on a failed directed


retry due to any failures on the Uu interface during the whole
call. When the switch is set to ON, no penalty is imposed on a
failed directed retry after best cell changed. By default, this
switch is set to OFF. 7. CMP_WBAMR_SUBFLOW_SWITCH:
When the switch is set to ON, the number of WB AMR service
substreams is configured according to the number of substreams
specified in the RAB ASSIGNMENT REQUEST message.
When the switch is set to OFF, the number of WB AMR service
substreams is 3. This switch is introduced to comply with the
Change Request (CR) specified in the related protocol, that is,
three substreams need to be established for a WB AMR service.
The switch CMP_WBAMR_SUBFLOW_SWITCH in this
version supports configuration synchronization and delivery, but
the RNC does not use this switch any longer. Future versions do
not support this switch. Therefore, it is recommended that users
avoid using this switch. 8.
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH:
The switch is used to solve the problem that different vendors'
RNCs interpret the cell capability bitmap differently on the Iur
interface. When the switch is set to ON, the RNC interprets the
cell capability bitmap in a sequence opposite to that specified by
the related protocol. When the switch is set to OFF, the RNC
interprets the cell capability bitmap in the sequence specified by
the related protocol. 9. CMP_MOCN_PLMN_SEL_SWITCH:
When the switch is set to ON, if the UE supports the MOCN
feature, the SRNC preferentially uses the PLMN of the UE's
homing operator in the RELOCATION REQUIRED message,
and the TRNC preferentially uses the PLMN of the UE's homing
operator in the LOCATION REPORT message and the DIRECT
TRANSFER message during relocation; if the UE does not
support the MOCN feature, the SRNC and the TRNC
preferentially use the common operator's PLMN in these above
messages. When the switch is set to OFF, the SRNC
preferentially uses the PLMN of the UE's homing operator in the
RELOCATION REQUIRED message, and the TRNC
preferentially uses the PLMN of the UE's homing operator in the
LOCATION REPORT message, but the TRNC preferentially
uses the common operator's PLMN in the DIRECT TRANSFER

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
04
02
W
RF
D01
06
12
03
W
RF
D02
04
00
W
RF
D02
08
03
W
RF
D01
06
85
W
RF
D02
07
01
W
RF
D02
01

de
(CE
LLDC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
DBHS
DP
A
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
HS
UP
A
Po
wer
Con
trol
DR

Description

message during relocation. 10.


CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH:
When the switch is set to ON, the RNC sets the "Support for
lossless SRNS relocation or for lossless DL RLC PDU size
change" IE transmitted on the Uu interface to TRUE only if the
UE supports both lossless SRNS relocation and downlink RLC
PDU size change. When the switch is set to OFF, the RNC sets
the "Support for lossless SRNS relocation or for lossless DL
RLC PDU size change" IE transmitted on the Uu interface to
TRUE if the UE supports lossless SRNS relocation or downlink
RLC PDU size change. 11.
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH: When
the switch is set to ON, the RNC sets the uplink mode of an
AMR service to maximum uplink rate, 0, and SID if the UE has
an established PS service. In this case, the AMRC algorithm is
not considered. 12.
CMP_SRB_H_AMR_DRD_HHO_SWITCH: Whether DRD can
be performed during AMR service establishment if signaling is
carried over HSPA. When this switch is turned on, DRD cannot
be performed during AMR service establishment when signaling
is carried over HSPA. When this switch is turned off, DRD can
be performed during AMR service establishment when signaling
is carried over HSPA. 13.
CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITCH:
Whether to enable the enhanced AMR anti-static function. When
this switch is turned on and the DRD procedure is triggered, the
RNC initiates an inter-frequency blind handover to move a UE to
the target cell and then processes an AMR service in the target
cell for the UE if one of following conditions is met: SRBs are
carried over HSPA channels and the UE is processing an AMR
service only. The US initiates an AMR service when a PS service
is still in progress. When this switch is turned off and the DRD
procedure is triggered, the RNC initiates an inter-frequency blind
handover and processes an AMR service in the target cell for the
UE at the same time if one of the preceding conditions is also
met. 14. CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH:
Whether to enable the DL Layer 2 Improvement feature for
E_PCH-incapable UEs processing only PTT services. When this
switch is turned on, the DL Layer 2 Improvement feature is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
10 D
Intr
odu
ctio
n
Pac
kag
e
AGP
S
Bas
ed
LC
S
Do
wnl
ink
Enh
anc
ed
L2
AM
R/
WB
AM
R
Spe
ech
Rat
es
Con
trol
Mul
ti
Fre
que
ncy

Description

enabled for E_PCH-incapable UEs processing only PTT


services. When this switch is turned off, the DL Layer 2
Improvement feature is not enabled for E_PCH-incapable UEs
processing only PTT services. 15.
CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH: Whether
the RLC entity can be re-established in only the uplink or
downlink during the state transition from CELL_FACH to
CELL_DCH (F2D for short). When this switch is turned off, the
RLC entity must be re-established in both uplink and downlink
during the F2D state transition. When this switch is turned on,
the RLC entity can be re-established in only the uplink or
downlink during the F2D state transition. For details, see 3GPP
TS 25.331. 16. CMP_DRD_SRBOVERH_SWITCH: Whether
signaling radio bearers (SRBs) can be switched over from FACH
or DCHs to HSPA channels during directed retry. When this
switch is turned off, SRBs can be switched over from FACH or
DCHs to HSPA channels during directed retry. When this switch
is turned on, SRBs cannot be switched over from FACH or
DCHs to HSPA channels during directed retry. Note: This is a
general switch for prohibiting SRBs from being switched over
from FACH or DCHs to HSPA channels during directed retry. To
enable the prohibition to take effect during RB setups, turn on
the CMP_RBSETUP_DRD_SRBOVERH_SWITCH under the
"CmpSwitch3" parameter. To enable the prohibition to take
effect during RB reconfiguration, turn on the
CMP_RBCFG_DRD_SRBOVERH_SWITCH under the
"CmpSwitch3" parameter. 17.
CMP_AMRC_FIXED_INITRATE_SWITCH: Whether the RNC
considers the cell congestion state when determining the initial
AMR rate mode during an AMR service setup and whether to
use the same rate mode for the uplink and downlink during RB
reconfigurations for WB-AMR services in the case of code
congestion. When this switch is set to off, the RNC considers the
cell congestion state during an AMR service setup. When AMRC
is enabled, the guaranteed bit rate (GBR) is used for uplink
admission if the uplink is congested. If the downlink is
congested, the GBRs are used for both uplink and downlink
admission. During RB reconfigurations for WB-AMR services,
the uplink and downlink can use different rate modes. However,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Ban
d
Net
wor
kin
g
Ma
nag
eme
nt

Description

the reconfigured uplink rate must be smaller than or equal to the


reconfigured downlink rate. When this switch is set to on, the
RNC does not consider the cell congestion state and the
maximum bit rates (MBRs) are used for uplink and downlink
admission during an AMR service setup. During RB
reconfigurations for WB-AMR services, the RNC uses the same
rate mode for the uplink and downlink. 18.
CMP_DL_LOAD_BALANCE_SWITCH: Whether the RNC
filters out the neighboring cells for blind handovers based on the
downlink load margin when inter-frequency DRD for load
balancing takes effect in the downlink during a blind-handoverbased non-periodic DRD. When this switch is turned off, a
neighboring cell for blind handovers cannot serve as the target
neighboring cell for inter-frequency blind handovers if the
difference between the downlink load margins of the
neighboring cell and the current cell is less than the value of the
"LdbDRDOffsetDCH" or "LdbDRDOffsetHSDPA" parameter.
When this switch is turned on, the RNC does not filter out any
neighboring cell for blind handovers. 19.
CMP_AMR_A_SUBFLOW_ZERO_BLOCK_SWITCH: Uplink
0 kbit/s transport format of AMR service subflow A, expressed
in TbNum * TbSize. When this switch is turned off, the format is
1*0. When this switch is turned on, the format is 0*TbSize. 20.
CMP_IUR_MULTI_RL_ADD_RETRY_SWITCH: Whether to
enable the compatibility algorithm when multiple RLs are added
to the same DRNC. When this switch is turned off, the RNC
stops attempting to re-establish the RL if an RL fails to be added
with the failure cause of "RadioNetwork:unspecified (14)".
When this switch is turned on, the RNC attempts to re-establish
the RL only once if an RL fails to be added with the failure cause
of "RadioNetwork:unspecified (14)". 21.
CMP_MBDR_CALL_TYPE_OTHER_AS_AMR_SWITCH:
Whether a conversational service of a UE complying with 3GPP
Release 6 and later are allowed for inter-RAT measurementbased directed retry (MBDR) if CallType of the conversational
service is Other. 22.
CMP_SRNSR_WAMR_MODE_0_RESTORE_SWITCH:
Whether the 0 kbit/s transport format is added on the Iu interface
during an incoming static relocation of a WB-AMR speech

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

service. When this switch is turned off, the 0 kbit/s transport


format is added on the Iu interface if the Uu interface has the 0
kbit/s transport format. When this switch is turned on, the 0
kbit/s transport format is added on the Iu interface if both the Uu
interface and the RAB parameters in the RELOCATION
REQUEST message have the 0 kbit/s transport format. 23.
CMP_GSM_NCELL_BAND_1900M_SWITCH: Whether the
frequency band of an inter-RAT neighboring cell must set to
1900 MHz. When this switch is turned on, the frequency band in
the following messages is set to 1900 MHz: SIB11 and SIB12
system information, inter-RAT measurement control, inter-RAT
handover, inter-RAT redirection, and inter-RAT neighboring cell
information sent back by the DRNC. When this switch is turned
off, the frequency band of the inter-RAT neighboring cell is set
as required. 24.
CMP_ACTIVESET_REPORT_WITH_SYN_SWITCH:
Whether the intra-frequency measurement reports of UEs must
contain synchronization information about the cells in the active
set. When this switch is turned off, the intra-frequency
measurement reports of UEs must contain synchronization
information about the cells in the active set. When this switch is
turned on, the intra-frequency measurement reports of UEs do
not need to contain synchronization information about the cells
in the active set. 25. CMP_READSFN_IND_IN_SIB_SWITCH:
Whether the RNC carries an indication to read the system frame
number (SFN) of an intra-frequency neighboring cell from
SIB11 or SIB12. When this switch is turned off, the RNC carries
the indication not to read the SFN of the intra-frequency
neighboring cell from SIB11 or SIB12. When this switch is
turned on, the RNC carries the indication to read the SFN of the
intra-frequency neighboring cell from SIB11 or SIB12. 26.
CMP_UE_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH:
Whether the UEs not supporting E_PCH use the Downlink
Enhanced L2 feature when processing the push to talk (PTT)
services. When this switch is turned off, the UEs not supporting
E_PCH use the Downlink Enhanced L2 feature when processing
the PTT services. When this switch is turned on, the UEs not
supporting E_PCH do not use the Downlink Enhanced L2
feature when processing the PTT services. 27.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_RELOC_IN_FACH_DEL_DCH_SWITCH: During a cell


update with combined relocation for a UE not in CELL_DCH
state: When this switch is turned off, the DRNC processes the
information about all dedicated transport channels upon
receiving a RELOCATION REQ message. When this switch is
turned on, the DRNC only processes the information about the
first dedicated transport channels upon receiving the
RELOCATION REQ message. In this case, the UE fails to
transit to the CELL_DCH state and new services cannot be
established. 28.
CMP_CELL_UPDATE_FACH_TRFFIC_MC_OPT: Switch for
measurement control optimization. When this switch is turned
on, the RNC does not send a measurement control message to a
UE if parameters related to traffic measurement control remain
unchanged after the UE in the CELL_FACH state performs a cell
update. If these parameters change, the RNC sends a
measurement control message to the UE.When this switch is
turned off, the RNC sends a measurement control message to a
UE after the UE in the CELL_FACH state performs a cell
update. 29.
CMP_MR_AGPS_MC_MSG_SEND_OPT_SWITCH: Whether
a UE can request additional AGPS data. 1: This switch is set to
on. The value of the additionalAssistDataReq IE is TRUE in MR
AGPS measurement control messages, indicating that a UE can
request additional AGPS data. 0: This switch is set to off. The
value of the additionalAssistDataReq IE is FALSE in MR AGPS
measurement control messages, indicating that a UE cannot
request additional AGPS data. Disuse Statement:This switch
CMP_WBAMR_SUBFLOW_SWITCH will be deleted from
later versions. Although the configuration interface in this
version supports delivery of the setting of this switch, the system
does not use this switch. Therefore, this switch is not
recommended.
GUI Value Range:
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH,
CMP_IUR_CMCF_SWITCH,
CMP_STTD_RL_ADD_SWITCH,
CMP_STTD_ASU_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH,
CMP_WBAMR_SUBFLOW_SWITCH,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH,
CMP_MOCN_PLMN_SEL_SWITCH,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH,
CMP_SRB_H_AMR_DRD_HHO_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITCH,
CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH,
CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH,
CMP_DRD_SRBOVERH_SWITCH,
CMP_AMRC_FIXED_INITRATE_SWITCH,
CMP_DL_LOAD_BALANCE_SWITCH,
CMP_AMR_A_SUBFLOW_ZERO_BLOCK_SWITCH,
CMP_IUR_MULTI_RL_ADD_RETRY_SWITCH,
CMP_MBDR_CALL_TYPE_OTHER_AS_AMR_SWITCH,
CMP_SRNSR_WAMR_MODE_0_RESTORE_SWITCH,
CMP_GSM_NCELL_BAND_1900M_SWITCH,
CMP_ACTIVESET_REPORT_WITH_SYN_SWITCH,
CMP_READSFN_IND_IN_SIB_SWITCH,
CMP_UE_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH,
CMP_RELOC_IN_FACH_DEL_DCH_SWITCH,
CMP_CELL_UPDATE_FACH_TRFFIC_MC_OPT,
CMP_MR_AGPS_MC_MSG_SEND_OPT_SWITCH
Unit: None
Actual Value Range:
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH,
CMP_IUR_CMCF_SWITCH,
CMP_STTD_RL_ADD_SWITCH,
CMP_STTD_ASU_SWITCH,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH,
CMP_WBAMR_SUBFLOW_SWITCH,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH,
CMP_MOCN_PLMN_SEL_SWITCH,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH,
CMP_SRB_H_AMR_DRD_HHO_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH,
CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH,
CMP_DRD_SRBOVERH_SWITCH,
CMP_AMRC_FIXED_INITRATE_SWITCH,
CMP_DL_LOAD_BALANCE_SWITCH,
CMP_AMR_A_SUBFLOW_ZERO_BLOCK_SWITCH,
CMP_IUR_MULTI_RL_ADD_RETRY_SWITCH,
CMP_MBDR_CALL_TYPE_OTHER_AS_AMR_SWITCH,
CMP_SRNSR_WAMR_MODE_0_RESTORE_SWITCH,
CMP_GSM_NCELL_BAND_1900M_SWITCH,
CMP_ACTIVESET_REPORT_WITH_SYN_SWITCH,
CMP_READSFN_IND_IN_SIB_SWITCH,
CMP_UE_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH,
CMP_RELOC_IN_FACH_DEL_DCH_SWITCH,
CMP_CELL_UPDATE_FACH_TRFFIC_MC_OPT,
CMP_MR_AGPS_MC_MSG_SEND_OPT_SWITCH
Default Value:
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH:0,CMP_IUB
R_DM_RTT_ALTERNATIVE_FMT_SWITCH:0,CMP_IUR_C
MCF_SWITCH:0,CMP_STTD_RL_ADD_SWITCH:0,CMP_ST
TD_ASU_SWITCH:0,CMP_RAB_DRD_ROLLBACK_PUNIS
H_SWITCH:0,CMP_WBAMR_SUBFLOW_SWITCH:0,CMP_I
UR_CELLCAP_BITMAP_TRANSFORM_SWITCH:0,CMP_M
OCN_PLMN_SEL_SWITCH:0,CMP_LOSSLESS_RELOC_RL
CPDUSIZECHG_SWITCH:0,CMP_CS_FIXED_RATE_WHEN
_PS_EXIST_SWITCH:0,CMP_SRB_H_AMR_DRD_HHO_SW
ITCH:0,CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITC
H:0,CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH:0,CMP_F
2D_RLC_ONESIDE_REBUILD_SWITCH:0,CMP_DRD_SRB
OVERH_SWITCH:0,CMP_AMRC_FIXED_INITRATE_SWIT
CH:0,CMP_DL_LOAD_BALANCE_SWITCH:0,CMP_AMR_
A_SUBFLOW_ZERO_BLOCK_SWITCH:0,CMP_IUR_MULT
I_RL_ADD_RETRY_SWITCH:0,CMP_MBDR_CALL_TYPE_
OTHER_AS_AMR_SWITCH:0,CMP_SRNSR_WAMR_MODE
_0_RESTORE_SWITCH:0,CMP_GSM_NCELL_BAND_1900
M_SWITCH:0,CMP_ACTIVESET_REPORT_WITH_SYN_S
WITCH:1,CMP_READSFN_IND_IN_SIB_SWITCH:1,CMP_U
E_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH:0,CMP_REL
OC_IN_FACH_DEL_DCH_SWITCH:0,CMP_CELL_UPDATE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

_FACH_TRFFIC_MC_OPT:0,CMP_MR_AGPS_MC_MSG_SE
ND_OPT_SWITCH:1
CmpS B SET
witch2 S UCO
C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D02
11
01
W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D15
02
07
W
RF
D01
01
01
W
RF
D15
02
50

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
4CHS
DP
A
3G
PP
R9

Meaning: 1. CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH:
When the switch is set to ON, the Iu user plane (UP) version is
not decreased if the Uu data rate set and the Iu data rate set in the
static relocation container are different. Otherwise, the Iu UP
version is decreased to version 1. 2.
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH:
When the switch is set to ON, RTT dedicated measurement
adopts the extended cell mode. When the switch is set to OFF,
RTT dedicated measurement does not adopt the extended cell
mode. This parameter is used to solve the problem that some
NodeBs do not support RTT dedicated measurement adopting
the extended cell mode. 3. CMP_IUR_CMCF_SWITCH: When
the switch is set to ON, compressed mode is started by using a
RADIO LINK RECONFIGURATION COMMIT message.
When the switch is set to OFF, compressed mode is started by
using a COMPRESSED MODE COMMAND message. 4.
CMP_STTD_RL_ADD_SWITCH: When the switch is set to
ON, the transmit diversity mode information element is always
carried in the RADIO LINK SETUP REQUEST message during
radio link establishment if a cell enabled with transmit diversity
and another cell disabled with transmit diversity exist under the
same NodeB. This parameter is used to solve the problem that
transmit diversity parameters are incorrectly configured for
softer handovers because the RADIO LINK ADDITION
REQUEST message does not carry the transmit diversity mode.
5. CMP_STTD_ASU_SWITCH: When a UE is soft-handed over
from a cell enabled with transmit diversity to a cell disabled with
transmit diversity, the UE may return active set update failure. If
the switch is set to ON, the RNC resends the active set update
message to the UE after an active set update failure. If the switch
is set to OFF, the RNC does not resend an active set update
message after an active set update failure. 6.
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH: When the
switch is set to OFF, a penalty is imposed on a failed directed
retry due to any failures on the Uu interface during the whole
call. When the switch is set to ON, no penalty is imposed on a

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D02
01
34
W
RF
D01
05
01
W
RF
D02
06
05
01
W
RF
D01
02
02
W
RF
D15
02
09
W
RF
D02
04
02
W

Spe
cifi
cati
ons
3CHS
DP
A
Pus
h to
Talk
Con
vers
atio
nal
Qo
S
Cla
ss
SR
NS
Rel
ocat
ion
(UE
Not
Inv
olve
d)
UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LL-

Description

failed directed retry after best cell changed. By default, this


switch is set to OFF. 7. CMP_WBAMR_SUBFLOW_SWITCH:
When the switch is set to ON, the number of WB AMR service
substreams is configured according to the number of substreams
specified in the RAB ASSIGNMENT REQUEST message.
When the switch is set to OFF, the number of WB AMR service
substreams is 3. This switch is introduced to comply with the
Change Request (CR) specified in the related protocol, that is,
three substreams need to be established for a WB AMR service.
The switch CMP_WBAMR_SUBFLOW_SWITCH in this
version supports configuration synchronization and delivery, but
the RNC does not use this switch any longer. Future versions do
not support this switch. Therefore, it is recommended that users
avoid using this switch. 8.
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH:
The switch is used to solve the problem that different vendors'
RNCs interpret the cell capability bitmap differently on the Iur
interface. When the switch is set to ON, the RNC interprets the
cell capability bitmap in a sequence opposite to that specified by
the related protocol. When the switch is set to OFF, the RNC
interprets the cell capability bitmap in the sequence specified by
the related protocol. 9. CMP_MOCN_PLMN_SEL_SWITCH:
When the switch is set to ON, if the UE supports the MOCN
feature, the SRNC preferentially uses the PLMN of the UE's
homing operator in the RELOCATION REQUIRED message,
and the TRNC preferentially uses the PLMN of the UE's homing
operator in the LOCATION REPORT message and the DIRECT
TRANSFER message during relocation; if the UE does not
support the MOCN feature, the SRNC and the TRNC
preferentially use the common operator's PLMN in these above
messages. When the switch is set to OFF, the SRNC
preferentially uses the PLMN of the UE's homing operator in the
RELOCATION REQUIRED message, and the TRNC
preferentially uses the PLMN of the UE's homing operator in the
LOCATION REPORT message, but the TRNC preferentially
uses the common operator's PLMN in the DIRECT TRANSFER
message during relocation. 10.
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH:
When the switch is set to ON, the RNC sets the "Support for

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D01
06
12
03
W
RF
D02
04
00
W
RF
D02
08
03
W
RF
D01
06
85
W
RF
D02
07
01
W
RF
D02
01
10

DC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
DBHS
DP
A
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
HS
UP
A
Po
wer
Con
trol
DR
D
Intr
odu

Description

lossless SRNS relocation or for lossless DL RLC PDU size


change" IE transmitted on the Uu interface to TRUE only if the
UE supports both lossless SRNS relocation and downlink RLC
PDU size change. When the switch is set to OFF, the RNC sets
the "Support for lossless SRNS relocation or for lossless DL
RLC PDU size change" IE transmitted on the Uu interface to
TRUE if the UE supports lossless SRNS relocation or downlink
RLC PDU size change. 11.
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH: When
the switch is set to ON, the RNC sets the uplink mode of an
AMR service to maximum uplink rate, 0, and SID if the UE has
an established PS service. In this case, the AMRC algorithm is
not considered. 12.
CMP_SRB_H_AMR_DRD_HHO_SWITCH: Whether DRD can
be performed during AMR service establishment if signaling is
carried over HSPA. When this switch is turned on, DRD cannot
be performed during AMR service establishment when signaling
is carried over HSPA. When this switch is turned off, DRD can
be performed during AMR service establishment when signaling
is carried over HSPA. 13.
CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITCH:
Whether to enable the enhanced AMR anti-static function. When
this switch is turned on and the DRD procedure is triggered, the
RNC initiates an inter-frequency blind handover to move a UE to
the target cell and then processes an AMR service in the target
cell for the UE if one of following conditions is met: SRBs are
carried over HSPA channels and the UE is processing an AMR
service only. The US initiates an AMR service when a PS service
is still in progress. When this switch is turned off and the DRD
procedure is triggered, the RNC initiates an inter-frequency blind
handover and processes an AMR service in the target cell for the
UE at the same time if one of the preceding conditions is also
met. 14. CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH:
Whether to enable the DL Layer 2 Improvement feature for
E_PCH-incapable UEs processing only PTT services. When this
switch is turned on, the DL Layer 2 Improvement feature is
enabled for E_PCH-incapable UEs processing only PTT
services. When this switch is turned off, the DL Layer 2
Improvement feature is not enabled for E_PCH-incapable UEs

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
ctio
n
Pac
kag
e
AGP
S
Bas
ed
LC
S
Do
wnl
ink
Enh
anc
ed
L2
AM
R/
WB
AM
R
Spe
ech
Rat
es
Con
trol
Mul
ti
Fre
que
ncy
Ban
d
Net

Description

processing only PTT services. 15.


CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH: Whether
the RLC entity can be re-established in only the uplink or
downlink during the state transition from CELL_FACH to
CELL_DCH (F2D for short). When this switch is turned off, the
RLC entity must be re-established in both uplink and downlink
during the F2D state transition. When this switch is turned on,
the RLC entity can be re-established in only the uplink or
downlink during the F2D state transition. For details, see 3GPP
TS 25.331. 16. CMP_DRD_SRBOVERH_SWITCH: Whether
signaling radio bearers (SRBs) can be switched over from FACH
or DCHs to HSPA channels during directed retry. When this
switch is turned off, SRBs can be switched over from FACH or
DCHs to HSPA channels during directed retry. When this switch
is turned on, SRBs cannot be switched over from FACH or
DCHs to HSPA channels during directed retry. Note: This is a
general switch for prohibiting SRBs from being switched over
from FACH or DCHs to HSPA channels during directed retry. To
enable the prohibition to take effect during RB setups, turn on
the CMP_RBSETUP_DRD_SRBOVERH_SWITCH under the
"CmpSwitch3" parameter. To enable the prohibition to take
effect during RB reconfiguration, turn on the
CMP_RBCFG_DRD_SRBOVERH_SWITCH under the
"CmpSwitch3" parameter. 17.
CMP_AMRC_FIXED_INITRATE_SWITCH: Whether the RNC
considers the cell congestion state when determining the initial
AMR rate mode during an AMR service setup and whether to
use the same rate mode for the uplink and downlink during RB
reconfigurations for WB-AMR services in the case of code
congestion. When this switch is set to off, the RNC considers the
cell congestion state during an AMR service setup. When AMRC
is enabled, the guaranteed bit rate (GBR) is used for uplink
admission if the uplink is congested. If the downlink is
congested, the GBRs are used for both uplink and downlink
admission. During RB reconfigurations for WB-AMR services,
the uplink and downlink can use different rate modes. However,
the reconfigured uplink rate must be smaller than or equal to the
reconfigured downlink rate. When this switch is set to on, the
RNC does not consider the cell congestion state and the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
wor
kin
g
Ma
nag
eme
nt

Description

maximum bit rates (MBRs) are used for uplink and downlink
admission during an AMR service setup. During RB
reconfigurations for WB-AMR services, the RNC uses the same
rate mode for the uplink and downlink. 18.
CMP_DL_LOAD_BALANCE_SWITCH: Whether the RNC
filters out the neighboring cells for blind handovers based on the
downlink load margin when inter-frequency DRD for load
balancing takes effect in the downlink during a blind-handoverbased non-periodic DRD. When this switch is turned off, a
neighboring cell for blind handovers cannot serve as the target
neighboring cell for inter-frequency blind handovers if the
difference between the downlink load margins of the
neighboring cell and the current cell is less than the value of the
"LdbDRDOffsetDCH" or "LdbDRDOffsetHSDPA" parameter.
When this switch is turned on, the RNC does not filter out any
neighboring cell for blind handovers. 19.
CMP_AMR_A_SUBFLOW_ZERO_BLOCK_SWITCH: Uplink
0 kbit/s transport format of AMR service subflow A, expressed
in TbNum * TbSize. When this switch is turned off, the format is
1*0. When this switch is turned on, the format is 0*TbSize. 20.
CMP_IUR_MULTI_RL_ADD_RETRY_SWITCH: Whether to
enable the compatibility algorithm when multiple RLs are added
to the same DRNC. When this switch is turned off, the RNC
stops attempting to re-establish the RL if an RL fails to be added
with the failure cause of "RadioNetwork:unspecified (14)".
When this switch is turned on, the RNC attempts to re-establish
the RL only once if an RL fails to be added with the failure cause
of "RadioNetwork:unspecified (14)". 21.
CMP_MBDR_CALL_TYPE_OTHER_AS_AMR_SWITCH:
Whether a conversational service of a UE complying with 3GPP
Release 6 and later are allowed for inter-RAT measurementbased directed retry (MBDR) if CallType of the conversational
service is Other. 22.
CMP_SRNSR_WAMR_MODE_0_RESTORE_SWITCH:
Whether the 0 kbit/s transport format is added on the Iu interface
during an incoming static relocation of a WB-AMR speech
service. When this switch is turned off, the 0 kbit/s transport
format is added on the Iu interface if the Uu interface has the 0
kbit/s transport format. When this switch is turned on, the 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

kbit/s transport format is added on the Iu interface if both the Uu


interface and the RAB parameters in the RELOCATION
REQUEST message have the 0 kbit/s transport format. 23.
CMP_GSM_NCELL_BAND_1900M_SWITCH: Whether the
frequency band of an inter-RAT neighboring cell must set to
1900 MHz. When this switch is turned on, the frequency band in
the following messages is set to 1900 MHz: SIB11 and SIB12
system information, inter-RAT measurement control, inter-RAT
handover, inter-RAT redirection, and inter-RAT neighboring cell
information sent back by the DRNC. When this switch is turned
off, the frequency band of the inter-RAT neighboring cell is set
as required. 24.
CMP_ACTIVESET_REPORT_WITH_SYN_SWITCH:
Whether the intra-frequency measurement reports of UEs must
contain synchronization information about the cells in the active
set. When this switch is turned off, the intra-frequency
measurement reports of UEs must contain synchronization
information about the cells in the active set. When this switch is
turned on, the intra-frequency measurement reports of UEs do
not need to contain synchronization information about the cells
in the active set. 25. CMP_READSFN_IND_IN_SIB_SWITCH:
Whether the RNC carries an indication to read the system frame
number (SFN) of an intra-frequency neighboring cell from
SIB11 or SIB12. When this switch is turned off, the RNC carries
the indication not to read the SFN of the intra-frequency
neighboring cell from SIB11 or SIB12. When this switch is
turned on, the RNC carries the indication to read the SFN of the
intra-frequency neighboring cell from SIB11 or SIB12. 26.
CMP_UE_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH:
Whether the UEs not supporting E_PCH use the Downlink
Enhanced L2 feature when processing the push to talk (PTT)
services. When this switch is turned off, the UEs not supporting
E_PCH use the Downlink Enhanced L2 feature when processing
the PTT services. When this switch is turned on, the UEs not
supporting E_PCH do not use the Downlink Enhanced L2
feature when processing the PTT services. 27.
CMP_RELOC_IN_FACH_DEL_DCH_SWITCH: During a cell
update with combined relocation for a UE not in CELL_DCH
state: When this switch is turned off, the DRNC processes the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

information about all dedicated transport channels upon


receiving a RELOCATION REQ message. When this switch is
turned on, the DRNC only processes the information about the
first dedicated transport channels upon receiving the
RELOCATION REQ message. In this case, the UE fails to
transit to the CELL_DCH state and new services cannot be
established. 28.
CMP_CELL_UPDATE_FACH_TRFFIC_MC_OPT: Switch for
measurement control optimization. When this switch is turned
on, the RNC does not send a measurement control message to a
UE if parameters related to traffic measurement control remain
unchanged after the UE in the CELL_FACH state performs a cell
update. If these parameters change, the RNC sends a
measurement control message to the UE.When this switch is
turned off, the RNC sends a measurement control message to a
UE after the UE in the CELL_FACH state performs a cell
update. 29.
CMP_MR_AGPS_MC_MSG_SEND_OPT_SWITCH: Whether
a UE can request additional AGPS data. 1: This switch is set to
on. The value of the additionalAssistDataReq IE is TRUE in MR
AGPS measurement control messages, indicating that a UE can
request additional AGPS data. 0: This switch is set to off. The
value of the additionalAssistDataReq IE is FALSE in MR AGPS
measurement control messages, indicating that a UE cannot
request additional AGPS data. Disuse Statement:This switch
CMP_WBAMR_SUBFLOW_SWITCH will be deleted from
later versions. Although the configuration interface in this
version supports delivery of the setting of this switch, the system
does not use this switch. Therefore, this switch is not
recommended.
GUI Value Range:
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH,
CMP_IUR_CMCF_SWITCH,
CMP_STTD_RL_ADD_SWITCH,
CMP_STTD_ASU_SWITCH,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH,
CMP_WBAMR_SUBFLOW_SWITCH,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_MOCN_PLMN_SEL_SWITCH,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH,
CMP_SRB_H_AMR_DRD_HHO_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITCH,
CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH,
CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH,
CMP_DRD_SRBOVERH_SWITCH,
CMP_AMRC_FIXED_INITRATE_SWITCH,
CMP_DL_LOAD_BALANCE_SWITCH,
CMP_AMR_A_SUBFLOW_ZERO_BLOCK_SWITCH,
CMP_IUR_MULTI_RL_ADD_RETRY_SWITCH,
CMP_MBDR_CALL_TYPE_OTHER_AS_AMR_SWITCH,
CMP_SRNSR_WAMR_MODE_0_RESTORE_SWITCH,
CMP_GSM_NCELL_BAND_1900M_SWITCH,
CMP_ACTIVESET_REPORT_WITH_SYN_SWITCH,
CMP_READSFN_IND_IN_SIB_SWITCH,
CMP_UE_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH,
CMP_RELOC_IN_FACH_DEL_DCH_SWITCH,
CMP_CELL_UPDATE_FACH_TRFFIC_MC_OPT,
CMP_MR_AGPS_MC_MSG_SEND_OPT_SWITCH
Unit: None
Actual Value Range:
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH,
CMP_IUR_CMCF_SWITCH,
CMP_STTD_RL_ADD_SWITCH,
CMP_STTD_ASU_SWITCH,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH,
CMP_WBAMR_SUBFLOW_SWITCH,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH,
CMP_MOCN_PLMN_SEL_SWITCH,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH,
CMP_SRB_H_AMR_DRD_HHO_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITCH,
CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH,
CMP_F2D_RLC_ONESIDE_REBUILD_SWITCH,
CMP_DRD_SRBOVERH_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_AMRC_FIXED_INITRATE_SWITCH,
CMP_DL_LOAD_BALANCE_SWITCH,
CMP_AMR_A_SUBFLOW_ZERO_BLOCK_SWITCH,
CMP_IUR_MULTI_RL_ADD_RETRY_SWITCH,
CMP_MBDR_CALL_TYPE_OTHER_AS_AMR_SWITCH,
CMP_SRNSR_WAMR_MODE_0_RESTORE_SWITCH,
CMP_GSM_NCELL_BAND_1900M_SWITCH,
CMP_ACTIVESET_REPORT_WITH_SYN_SWITCH,
CMP_READSFN_IND_IN_SIB_SWITCH,
CMP_UE_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH,
CMP_RELOC_IN_FACH_DEL_DCH_SWITCH,
CMP_CELL_UPDATE_FACH_TRFFIC_MC_OPT,
CMP_MR_AGPS_MC_MSG_SEND_OPT_SWITCH
Default Value:
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH:0,CMP_IUB
R_DM_RTT_ALTERNATIVE_FMT_SWITCH:0,CMP_IUR_C
MCF_SWITCH:0,CMP_STTD_RL_ADD_SWITCH:0,CMP_ST
TD_ASU_SWITCH:0,CMP_RAB_DRD_ROLLBACK_PUNIS
H_SWITCH:0,CMP_WBAMR_SUBFLOW_SWITCH:0,CMP_I
UR_CELLCAP_BITMAP_TRANSFORM_SWITCH:0,CMP_M
OCN_PLMN_SEL_SWITCH:0,CMP_LOSSLESS_RELOC_RL
CPDUSIZECHG_SWITCH:0,CMP_CS_FIXED_RATE_WHEN
_PS_EXIST_SWITCH:0,CMP_SRB_H_AMR_DRD_HHO_SW
ITCH:0,CMP_UU_AMR_DRD_HHO_COMPAT_ENH_SWITC
H:0,CMP_SINGLE_PTT_USE_DL_ENL2_SWITCH:0,CMP_F
2D_RLC_ONESIDE_REBUILD_SWITCH:0,CMP_DRD_SRB
OVERH_SWITCH:0,CMP_AMRC_FIXED_INITRATE_SWIT
CH:0,CMP_DL_LOAD_BALANCE_SWITCH:0,CMP_AMR_
A_SUBFLOW_ZERO_BLOCK_SWITCH:0,CMP_IUR_MULT
I_RL_ADD_RETRY_SWITCH:0,CMP_MBDR_CALL_TYPE_
OTHER_AS_AMR_SWITCH:0,CMP_SRNSR_WAMR_MODE
_0_RESTORE_SWITCH:0,CMP_GSM_NCELL_BAND_1900
M_SWITCH:0,CMP_ACTIVESET_REPORT_WITH_SYN_S
WITCH:1,CMP_READSFN_IND_IN_SIB_SWITCH:1,CMP_U
E_NOT_USE_DL_ENL2_EXIST_PTT_SWITCH:0,CMP_REL
OC_IN_FACH_DEL_DCH_SWITCH:0,CMP_CELL_UPDATE
_FACH_TRFFIC_MC_OPT:0,CMP_MR_AGPS_MC_MSG_SE
ND_OPT_SWITCH:1

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RsvdP B SET
ara1
S URR
C CTRL
6 SWIT
9 CH
0
0

W
RF
D01
01
01

3G
PP
R9
Spe
cifi
cati
ons

Description

Meaning: 1) NAS_QOS_MOD_SWITCH (QoS Change Switch


for NAS) 1: This switch is turned on. For UEs whose HS-DSCH
category is smaller than 13, if the maximum downlink rate
specified in the PDP activation requests from the UEs exceeds
16 Mbit/s, the requests are sent to the CN after the rate is
changed to 16 Mbit/s. 0: This switch is turned off. The PDP
activation requests are sent to the CN without changing the
maximum downlink rate.
2)SYSHO_CSIN_PERMIT_SWITCH(Switch for Permit
Incoming CS Inter-RAT Handovers) 1: This switch is turned on.
CS Inter-RAT Handovers are permitted. 0: This switch is turned
off. CS Inter-RAT Handovers are not permitted.
GUI Value Range: RSVDBIT1_BIT1,
NAS_QOS_MOD_SWITCH, RSVDBIT1_BIT3,
RSVDBIT1_BIT4, RSVDBIT1_BIT5, RSVDBIT1_BIT6,
RSVDBIT1_BIT7, RSVDBIT1_BIT8, RSVDBIT1_BIT9,
RSVDBIT1_BIT10, RSVDBIT1_BIT11, RSVDBIT1_BIT12,
RSVDBIT1_BIT13, RSVDBIT1_BIT14, RSVDBIT1_BIT15,
RSVDBIT1_BIT16, SYSHO_CSIN_PERMIT_SWITCH,
RSVDBIT1_BIT18, RSVDBIT1_BIT19, RSVDBIT1_BIT20,
RSVDBIT1_BIT21, RSVDBIT1_BIT22, RSVDBIT1_BIT23,
RSVDBIT1_BIT24, RSVDBIT1_BIT25, RSVDBIT1_BIT26,
RSVDBIT1_BIT27, RSVDBIT1_BIT28, RSVDBIT1_BIT29,
RSVDBIT1_BIT30, RSVDBIT1_BIT31, RSVDBIT1_BIT32
Unit: None
Actual Value Range: RSVDBIT1_BIT1,
NAS_QOS_MOD_SWITCH, RSVDBIT1_BIT3,
RSVDBIT1_BIT4, RSVDBIT1_BIT5, RSVDBIT1_BIT6,
RSVDBIT1_BIT7, RSVDBIT1_BIT8, RSVDBIT1_BIT9,
RSVDBIT1_BIT10, RSVDBIT1_BIT11, RSVDBIT1_BIT12,
RSVDBIT1_BIT13, RSVDBIT1_BIT14, RSVDBIT1_BIT15,
RSVDBIT1_BIT16, SYSHO_CSIN_PERMIT_SWITCH,
RSVDBIT1_BIT18, RSVDBIT1_BIT19, RSVDBIT1_BIT20,
RSVDBIT1_BIT21, RSVDBIT1_BIT22, RSVDBIT1_BIT23,
RSVDBIT1_BIT24, RSVDBIT1_BIT25, RSVDBIT1_BIT26,
RSVDBIT1_BIT27, RSVDBIT1_BIT28, RSVDBIT1_BIT29,
RSVDBIT1_BIT30, RSVDBIT1_BIT31, RSVDBIT1_BIT32
Default Value:
RSVDBIT1_BIT1:0,NAS_QOS_MOD_SWITCH:0,RSVDBIT1

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

_BIT3:0,RSVDBIT1_BIT4:0,RSVDBIT1_BIT5:0,RSVDBIT1_
BIT6:0,RSVDBIT1_BIT7:0,RSVDBIT1_BIT8:0,RSVDBIT1_B
IT9:0,RSVDBIT1_BIT10:0,RSVDBIT1_BIT11:0,RSVDBIT1_
BIT12:0,RSVDBIT1_BIT13:0,RSVDBIT1_BIT14:0,RSVDBIT
1_BIT15:0,RSVDBIT1_BIT16:0,SYSHO_CSIN_PERMIT_SWI
TCH:1,RSVDBIT1_BIT18:1,RSVDBIT1_BIT19:1,RSVDBIT1_
BIT20:1,RSVDBIT1_BIT21:1,RSVDBIT1_BIT22:1,RSVDBIT
1_BIT23:1,RSVDBIT1_BIT24:1,RSVDBIT1_BIT25:1,RSVDBI
T1_BIT26:1,RSVDBIT1_BIT27:1,RSVDBIT1_BIT28:1,RSVD
BIT1_BIT29:1,RSVDBIT1_BIT30:1,RSVDBIT1_BIT31:1,RSV
DBIT1_BIT32:1
RsvdP B SET
ara1
S URR
C CTRL
6 SWIT
9 CH
1
0

W
RF
D01
01
01

3G
PP
R9
Spe
cifi
cati
ons

Meaning: 1) NAS_QOS_MOD_SWITCH (QoS Change Switch


for NAS) 1: This switch is turned on. For UEs whose HS-DSCH
category is smaller than 13, if the maximum downlink rate
specified in the PDP activation requests from the UEs exceeds
16 Mbit/s, the requests are sent to the CN after the rate is
changed to 16 Mbit/s. 0: This switch is turned off. The PDP
activation requests are sent to the CN without changing the
maximum downlink rate.
2)SYSHO_CSIN_PERMIT_SWITCH(Switch for Permit
Incoming CS Inter-RAT Handovers) 1: This switch is turned on.
CS Inter-RAT Handovers are permitted. 0: This switch is turned
off. CS Inter-RAT Handovers are not permitted.
GUI Value Range: RSVDBIT1_BIT1,
NAS_QOS_MOD_SWITCH, RSVDBIT1_BIT3,
RSVDBIT1_BIT4, RSVDBIT1_BIT5, RSVDBIT1_BIT6,
RSVDBIT1_BIT7, RSVDBIT1_BIT8, RSVDBIT1_BIT9,
RSVDBIT1_BIT10, RSVDBIT1_BIT11, RSVDBIT1_BIT12,
RSVDBIT1_BIT13, RSVDBIT1_BIT14, RSVDBIT1_BIT15,
RSVDBIT1_BIT16, SYSHO_CSIN_PERMIT_SWITCH,
RSVDBIT1_BIT18, RSVDBIT1_BIT19, RSVDBIT1_BIT20,
RSVDBIT1_BIT21, RSVDBIT1_BIT22, RSVDBIT1_BIT23,
RSVDBIT1_BIT24, RSVDBIT1_BIT25, RSVDBIT1_BIT26,
RSVDBIT1_BIT27, RSVDBIT1_BIT28, RSVDBIT1_BIT29,
RSVDBIT1_BIT30, RSVDBIT1_BIT31, RSVDBIT1_BIT32
Unit: None
Actual Value Range: RSVDBIT1_BIT1,
NAS_QOS_MOD_SWITCH, RSVDBIT1_BIT3,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RSVDBIT1_BIT4, RSVDBIT1_BIT5, RSVDBIT1_BIT6,


RSVDBIT1_BIT7, RSVDBIT1_BIT8, RSVDBIT1_BIT9,
RSVDBIT1_BIT10, RSVDBIT1_BIT11, RSVDBIT1_BIT12,
RSVDBIT1_BIT13, RSVDBIT1_BIT14, RSVDBIT1_BIT15,
RSVDBIT1_BIT16, SYSHO_CSIN_PERMIT_SWITCH,
RSVDBIT1_BIT18, RSVDBIT1_BIT19, RSVDBIT1_BIT20,
RSVDBIT1_BIT21, RSVDBIT1_BIT22, RSVDBIT1_BIT23,
RSVDBIT1_BIT24, RSVDBIT1_BIT25, RSVDBIT1_BIT26,
RSVDBIT1_BIT27, RSVDBIT1_BIT28, RSVDBIT1_BIT29,
RSVDBIT1_BIT30, RSVDBIT1_BIT31, RSVDBIT1_BIT32
Default Value:
RSVDBIT1_BIT1:0,NAS_QOS_MOD_SWITCH:0,RSVDBIT1
_BIT3:0,RSVDBIT1_BIT4:0,RSVDBIT1_BIT5:0,RSVDBIT1_
BIT6:0,RSVDBIT1_BIT7:0,RSVDBIT1_BIT8:0,RSVDBIT1_B
IT9:0,RSVDBIT1_BIT10:0,RSVDBIT1_BIT11:0,RSVDBIT1_
BIT12:0,RSVDBIT1_BIT13:0,RSVDBIT1_BIT14:0,RSVDBIT
1_BIT15:0,RSVDBIT1_BIT16:0,SYSHO_CSIN_PERMIT_SWI
TCH:1,RSVDBIT1_BIT18:1,RSVDBIT1_BIT19:1,RSVDBIT1_
BIT20:1,RSVDBIT1_BIT21:1,RSVDBIT1_BIT22:1,RSVDBIT
1_BIT23:1,RSVDBIT1_BIT24:1,RSVDBIT1_BIT25:1,RSVDBI
T1_BIT26:1,RSVDBIT1_BIT27:1,RSVDBIT1_BIT28:1,RSVD
BIT1_BIT29:1,RSVDBIT1_BIT30:1,RSVDBIT1_BIT31:1,RSV
DBIT1_BIT32:1
Optim
ization
Switc
h3

B
S
C
6
9
0
0

SET
URR
CTRL
SWIT
CH

W
RF
D01
09
01
W
RF
D01
06
10
06
W
RF

Intr
a
RN
C
UR
A
Upd
ate
HS
DP
A
Mo
bilit
y
Ma

Meaning: 1)SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH
Whether the RNC measures one successful handover or
relocation when receiving an Iu release command message with
the cause value "Network Optimization" from the CN during an
outgoing relocation or outgoing inter-RAT handover procedure.
1: This switch is turned on. The RNC measures one successful
handover or relocation. 0: This switch is turned off. The RNC
measures one failed handover or relocation.
2)RL_REEST_PS_ON_FACH_SWITCH Whether PS services
are established on the FACH upon call reestablishment. 1: This
switch is turned on. PS services are established on the FACH
upon a call reestablishment triggered by either of the following
factors: - All downlink radio links for a UE are out of
synchronization. - The SRB over the Uu interface is reset. 0:
This switch is turned off. PS services are established on the DCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D02
02
03
W
RF
D01
09
02
W
RF
D01
01
01
W
RF
D01
05
10
W
RF
D02
02
02
W
RF
D01
08
01
W
RF
D01

nag
eme
nt
Inte
r
RN
C
Soft
Han
dov
er
Inte
r
RN
C
UR
A
Upd
ate
3G
PP
R9
Spe
cifi
cati
ons
3.4/
6.8/
13.6
/27.
2Kb
ps
RR
C
Con
nect
ion
and
Rad

Description

upon a call reestablishment triggered by either of the preceding


factors. 3)CELLUPDATE_MEASUREMENT_OPT_SWITCH
Whether the RNC repeatedly calculates the number of cell
update attempts. A UE sends a CELL UPDATE message in cell 1
and then sends another in cell 2 before receiving a CELL
UPDATE CONFIRM message from the RNC or responding to
the CELL UPDATE CONFIRM message. The UE completes the
cell update procedure in cell 2. In the preceding scenario, 1: This
switch is turned on. The RNC measures one cell update attempt
only. 0: This switch is turned off. The RNC repeatedly measures
cell update attempts.
4)D2F_PROCEDURE_OPTIMIZATION_SWITCH Whether the
optimized D2F procedure takes effect. 1: This switch is turned
on. An expired D2F procedure is considered as successful if
either of the following conditions is met: - The RB
reconfiguration message is sent in unacknowledged mode (UM),
and all the RLs in the active set receive an RL Fail indication. The RB reconfiguration message is sent in the acknowledged
mode (AM), and an ACK response is received from the UE. If
neither of the preceding conditions is met, the D2F procedure is
considered as expired. 0: This switch is turned off. The
optimized D2F procedure does not take effect. This switch is set
to 0 by default.
5)F2D_PROCEDURE_OPTIMIZATION_SWITCH Whether the
optimized F2D procedure takes effect. 1: This switch is turned
on. An expired F2D procedure is considered as successful if the
RL status is normal. If the RL status is not normal, the F2D
procedure is considered as expired. 0: This switch is turned off.
The optimized F2D procedure does not take effect. This switch is
set to 0 by default.
6)FOREVER_PCH_CTRL_PLANE_SHARE_OPT 1: This
switch is turned on. Load sharing of UEs in the CELL_PCH state
is not triggered among SPU subsystems and the UEs in the
CELL_PCH state are periodically released on this SPU
subsystem if the following conditions are met: - The CPU usage
of the SPU subsystem exceeds a specified threshold and exceeds
the average CPU usage of the SPU subsystems under the RNC. The number of online UEs in the CELL_PCH state on this SPU
subsystem exceeds the average number of UEs in the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
08 io
02 Acc
ess
Bea
rer
Esta
blis
hme
nt
and
Rel
ease
Intr
a
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Cell
Upd
ate
Inte
r
RN
C
Cell
Upd
ate

Description

CELL_PCH state on the SPU subsystems under the RNC. 0:


This switch is turned off. Load sharing of UEs in the
CELL_PCH state is triggered among SPU subsystems if the
following conditions are met: - The CPU usage of the SPU
subsystem exceeds a specified threshold and exceeds the average
CPU usage of the SPU subsystems under the RNC. - The number
of online UEs in the CELL_PCH state on this SPU subsystem
exceeds the average number of UEs in the CELL_PCH state on
the SPU subsystems under the RNC.
7)FOREVER_PCH_USER_PLANE_SHARE_OPT 1: This
switch is turned on. The RNC selects another DSP to perform
load sharing on the user plane when always online users are
activated. 0: This switch is turned off. The RNC does not
perform load sharing on the user plane when always online users
are activated.
8)RAB_REL_SRV_CELL_CHG_CROSS_SWITCH Whether
the serving cell change procedure is allowed during the release
of all PS RABs. 1: This switch is turned on. The serving cell
change procedure is not allowed during the release of all PS
RABs. 0: This switch is turned off. The serving cell change
procedure is allowed during the release of all PS RABs.
9)SCRIWITHCAUSE_OVERLAP_SWITCH How the RNC will
react if it receives an SCRI message with the cause value "UE
Requested PS Data session end" in the middle of another
procedure. 1: This switch is turned on. The RNC maintains the
original RRC state and does not release the connection of the
related UE if the RNC receives an SCRI message with the
preceding cause value in the middle of another procedure. 0:
This switch is turned off. The RNC releases the connection of
the UE if both of the following conditions are met: The RNC
receives an SCRI message with the preceding cause value in the
middle of another procedure. The TAC of the UE does not
belong to the TACs that are enabled with fast dormancy.
10)P2F_CUC_REPEAT_SWITCH Whether the RNC retransmits
a CELL UPDATE CONFIRM message to a UE that is
transitioning from the CELL_PCH or URA_PCH state to the
CELL_FACH state. 1: This switch is turned on. The RNC
retransmits a CELL UPDATE CONFIRM message to a UE that
is transitioning from the CELL_PCH or URA_PCH state to the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CELL_FACH state. 0: This switch is turned off. The RNC does


not retransmit a CELL UPDATE CONFIRM message to a UE
that is transitioning from the CELL_PCH or URA_PCH state to
the CELL_FACH state.
11)UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
Whether to notify the NodeB of the abnormal RL release due to
poor Uu interface quality. 1: This switch is turned on. The RNC
notifies the NodeB of the abnormal RL release due to poor Uu
interface quality. 0: This switch is turned off. The RNC does not
notify the NodeB of the abnormal RL release due to poor Uu
interface quality.
12)D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH
Whether the RNC considers the D2F state transition as
successful if the RNC does not receive a response message from
the UE within the specified period after sending a RADIO
BEARER RECONFIGURTION message to the UE in
acknowledged mode (AM). 1: This switch is turned on. The
RNC considers the D2F state transition as successful if the
following conditions are met: The RNC does not receive a
response from the UE within the specified period after sending a
RADIO BEARER RECONFIGURATION message to the UE in
AM. All radio links (RLs) for the UE are out of synchronization.
The RLCs for all TRBs are in AM. If any of the preceding
conditions is not met, the RNC undoes the D2F state transition.
0: This switch is turned off. The RNC undoes the D2F state
transition if the RNC does not receive a response from the UE
within the specified period after sending a RADIO BEARER
RECONFIGURATION message to the UE in AM.
13)AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH
(Response Timer Optimization Switch for D2F and F2D
Procedures in AM) Length policy for the timer set for the RNC
to wait for a response message from the UE after the RNC sends
a RADIO BEARER RECONFIGURATION message to the UE
in AM during the D2F and F2D state transitions. 1: This switch
is turned on. The length of the timer equals its configured value
(value of the "RbRecfgRspTmr" parameter in the "SET
USTATETIMER" command) plus four seconds. 0: This switch is
turned off. The length of this timer equals its configured value.
14)D2P_DT_MSG_BUFFER_SWITCH (DT Message Buffer

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Switch During D2P) Whether the RNC buffers the DIRECT


TRANSFER message sent by the CN during the D2P state
transition. 1: This switch is turned on. The RNC buffers the
DIRECT TRANSFER message. The RNC sends a paging
message to the UE after the D2P state transition is complete and
then sends the buffered DIRECT TRANSFER message to the
UE. 0: This switch is turned off. The RNC forwards the DIRECT
TRANSFER message to the UE immediately after receiving it.
15)CM_CODE_CONFLICT_OPT_SWITCH Used to solve code
resource conflicts in compressed mode. 1: This switch is turned
on. Code resource conflicts in compressed mode are solved. 0:
This switch is turned off. Code resource conflicts in compressed
mode are not solved.
16)H_SERV_CELL_CHANGE_MSG_OPT_SWITCH(Enable H
Serving Cell Change MSG Size Reduction) Whether to reduce
the size of the HSDPA serving cell change message. 1: This
switch is turned on. The size of the HSDPA serving cell change
message is reduced. 0: This switch is turned off. The size of the
HSDPA serving cell change message is not reduced.
17)FAST_HSDPA_SERV_CELL_CHANGE_SWITCH (Fast
HSDPA Serving Cell Change Optimization Switch) Whether to
enable the fast HSDPA serving cell change optimization
function. 1: This switch is turned on. The RNC includes the IE
Delay restriction flag in the PHYSICAL CHANNEL
RECONFIGURATION message. For details about the IE Delay
restriction flag, see section 10.2.22 in 3GPP TS25.331. 0: This
switch is turned off. The RNC does not include the IE Delay
restriction flag in the PHYSICAL CHANNEL
RECONFIGURATION message.
18)RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH(S
HO Counting Correction Switch in RL Reestablish) When the
RL reestablishment function is enabled, a soft handover
procedure is considered as successful even if the ASU CMP
message is not received if RL reestablishment is triggered during
the soft handover. This parameter specifies whether to correct the
counting of successful soft handovers when RL reestablishment
is triggered during the soft handover. 1: This switch is turned on.
Such a soft handover procedure is considered as failed. 0: This
switch is turned off. Such a soft handover procedure is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

considered as successful.
19)COUNT_STATE_CHG_BY_RAB_EHN_SWITCH Whether
to enable certain state transition-related counters to be
incremented on a PS RAB basis. These counters include the
VS.DCCC.P2D.Att, VS.DCCC.P2D.Succ, VS.DCCC.Att.D2U,
and VS.DCCC.Succ.D2U counters. 1: This switch is turned on.
These counters are incremented on a PS RAB basis. 0: This
switch is turned off. These counters are incremented on a UE
basis. 20)RAB_RELATED_COUNTER_OPT_SWITCH(RAB
Setup Failure Statistical Optimization Switch) Whether to
optimize the statistics of counters measuring RAB setup failures
and abnormal RAB releases. 1: This switch is turned on. Under
this circumstance, the statistics of counters measuring RAB
setup failures and abnormal RAB releases are optimized. 0: This
switch is turned off. Under this circumstance, the statistics of
counters measuring RAB setup failures and abnormal RAB
releases are not optimized.
21)CELLUPDATE_PROCEDURE_OPT_SWITCH (Cell
Update Procedure Optimization Switch) Whether to enable the
optimized processing for the cell update procedure. 1: This
switch is set to on. The RNC supports the overlapping of these
two procedures: cell update procedure caused by RL failure and
P2D/D2P/D2F state transition procedure. For UEs in the
CELL_DCH state, the RNC performs a cell update procedure
based on the retransmitted CELL UPDATE message if the
retransmitted message carries an SRB or TRB reset indication.
For UEs in the CELL_PCH or URA_PCH state, when the
number of CELL UPDATE messages with the cause value
paging response or UL data transmission exceeds the value
specified by N381, the RNC sends an RRC connection release
message to the UE in the cell where the UE sends the last CELL
UPDATE message. For UEs in states other than CELL_DCH or
in the middle of state transitions other than P2D, if the SRNC
receives a CELL UPDATE message with HRNTI from a UE
through the DRNC while waiting for the UE's response to the
CELL UPDATE CONFIRM message, the SRNC considers the
message as a retransmitted one. 0. This switch is set to off. The
optimized processing for the cell update procedure is not
supported. 22)PTT_PAGING_PRD_CRRCT_SWITCH(Correct

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

the Paging Retransmission for PTT Services over Uu) Whether


to correct the retransmission period of paging messages for push
to talk (PTT) services over the Uu interface. 1: This switch is set
to on, the retransmission period of PTT services is corrected.
That is, if the RNC does not receive a paging response within
320 ms after sending a paging message, the RNC retransmits the
paging message. 0: This switch is set to off, the retransmission
period of PTT services is not corrected. That is, the RNC
retransmits a paging message only when it does not receive a
paging response within 640 ms after sending a paging message.
23)RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH
(Respond to RAB Assignment Request upon RRC Release)
Whether the RNC processes the RAB ASSIGNMENT
REQUEST message and returns a RAB ASSIGNMENT
RESPONSE message to the CN in the following scenario: After
receiving a RAB RELEASE REQUEST message from the RNC
to release the last RAB of a UE, the CN does not return an IU
RELEASE COMMAND message but returns a RAB
ASSIGNMENT REQUEST instead. 1: This switch is set to on.
The RNC processes the RAB ASSIGNMENT REQUEST
message and returns a RAB ASSIGNMENT RESPONSE
message to the CN in the preceding scenario. 0: This switch is
set to off. The RNC does not process the RAB ASSIGNMENT
REQUEST message in the preceding scenario.
24)L2U_UP_DELAY_OPT_SWITCH (L2U UP Delay
Optimization Switch) Whether the RNC returns a
RELOCATION COMPLETE message to the CN to start UP data
transmission immediately after receiving a HANDOVER TO
UTRAN COMPLETE message during a LTE-to-UMTS
handover. 1: This switch is set to on. The RNC immediately
returns a RELOCATION COMPLETE message to the CN in the
preceding scenario. 0: This switch is set to off. After the RNC
queries the UE's capability and the security mode procedure is
complete, the RNC returns a RELOCATION COMPLETE
message to the CN.
25)PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH
(Optimize UE Selection for Outgoing Inter-RAT Handover in
Basic Congestion) Whether the LDR algorithm on the RNC side
updates the attribute of outgoing inter-RAT handover for a UE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

after an F2D, P2D, or D2D state transition procedure. 1: This


switch is set to on. The LDR algorithm on the RNC side updates
the attribute of outgoing inter-RAT handover for a UE after an
F2D, P2D, or D2D state transition procedure. In this way, the
LDR algorithm on the RNC side can select appropriate UEs for
outgoing inter-RAT handovers when the cell is in basic
congestion state. 0: This switch is set to off. The LDR algorithm
on the RNC side does not update the attribute of outgoing interRAT handover for a UE after an F2D, P2D, or D2D state
transition procedure.
GUI Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH(SYS_RELO
C_OUT_SUCC_STAT_OPT_SWITCH),
RL_REEST_PS_ON_FACH_SWITCH(RL_REEST_PS_ON_F
ACH_SWITCH),
CELLUPDATE_MEASUREMENT_OPT_SWITCH(CELLUPD
ATE_MEASUREMENT_OPT_SWITCH),
D2F_PROCEDURE_OPTIMIZATION_SWITCH(D2F_PROCE
DURE_OPTIMIZATION_SWITCH),
F2D_PROCEDURE_OPTIMIZATION_SWITCH(F2D_PROCE
DURE_OPTIMIZATION_SWITCH),
FOREVER_PCH_CTRL_PLANE_SHARE_OPT(FOREVER_P
CH_CTRL_PLANE_SHARE_OPT),
FOREVER_PCH_USER_PLANE_SHARE_OPT(FOREVER_P
CH_USER_PLANE_SHARE_OPT),
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH(RAB_REL_
SRV_CELL_CHG_CROSS_SWITCH),
SCRIWITHCAUSE_OVERLAP_SWITCH(SCRIWITHCAUSE
_OVERLAP_SWITCH),
P2F_CUC_REPEAT_SWITCH(P2F_CUC_REPEAT_SWITCH)
,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH(UU_ABN
_REL_INFO_NOTIFY_NODEB_SWITCH),
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH(D2F_A
M_PROCEDURE_OPTIMIZATION_SWITCH),
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH(AM_D
2F_F2D_RESTMR_OPTIMIZATION_SWITCH),
D2P_DT_MSG_BUFFER_SWITCH(D2P_DT_MSG_BUFFER
_SWITCH),

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CM_CODE_CONFLICT_OPT_SWITCH(CM_CODE_CONFLI
CT_OPT_SWITCH),
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH(H_SERV_C
ELL_CHANGE_MSG_OPT_SWITCH),
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH(FAST_HS
DPA_SERV_CELL_CHANGE_SWITCH),
RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH(RL
RST_ASU_SUCC_COUNTERS_CORRECT_SWITCH),
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH(COUNT_S
TATE_CHG_BY_RAB_EHN_SWITCH),
RAB_RELATED_COUNTER_OPT_SWITCH(RAB_RELATE
D_COUNTER_OPT_SWITCH),
CELLUPDATE_PROCEDURE_OPT_SWITCH(CELLUPDATE
_PROCEDURE_OPT_SWITCH),
PTT_PAGING_PRD_CRRCT_SWITCH(PTT_PAGING_PRD_
CRRCT_SWITCH),
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH(RRC_R
EL_STATUS_RSP_RAB_ASS_REQ_SWITCH),
L2U_UP_DELAY_OPT_SWITCH(L2U_UP_DELAY_OPT_S
WITCH),
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH(PRI_
LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH)
Unit: None
Actual Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH,
RL_REEST_PS_ON_FACH_SWITCH,
CELLUPDATE_MEASUREMENT_OPT_SWITCH,
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH,
D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH,
L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH
Default Value:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH:1,RL_REES
T_PS_ON_FACH_SWITCH:0,CELLUPDATE_MEASUREME
NT_OPT_SWITCH:0,D2F_PROCEDURE_OPTIMIZATION_S
WITCH:0,F2D_PROCEDURE_OPTIMIZATION_SWITCH:0,F
OREVER_PCH_CTRL_PLANE_SHARE_OPT:0,FOREVER_P
CH_USER_PLANE_SHARE_OPT:0,RAB_REL_SRV_CELL_
CHG_CROSS_SWITCH:0,SCRIWITHCAUSE_OVERLAP_S
WITCH:0,P2F_CUC_REPEAT_SWITCH:0,UU_ABN_REL_IN
FO_NOTIFY_NODEB_SWITCH:0,D2F_AM_PROCEDURE_
OPTIMIZATION_SWITCH:0,AM_D2F_F2D_RESTMR_OPTI
MIZATION_SWITCH:0,D2P_DT_MSG_BUFFER_SWITCH:0,
CM_CODE_CONFLICT_OPT_SWITCH:1,H_SERV_CELL_C
HANGE_MSG_OPT_SWITCH:0,FAST_HSDPA_SERV_CELL
_CHANGE_SWITCH:0,RLRST_ASU_SUCC_COUNTERS_C
ORRECT_SWITCH:0,COUNT_STATE_CHG_BY_RAB_EHN
_SWITCH:0,RAB_RELATED_COUNTER_OPT_SWITCH:0,C
ELLUPDATE_PROCEDURE_OPT_SWITCH:1,PTT_PAGING
_PRD_CRRCT_SWITCH:0,RRC_REL_STATUS_RSP_RAB_A
SS_REQ_SWITCH:0,L2U_UP_DELAY_OPT_SWITCH:1,PRI
_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH:0
Optim
ization
Switc
h3

B
S
C
6
9
1
0

SET
URR
CTRL
SWIT
CH

W
RF
D01
09
01
W

Intr
a
RN
C
UR
A
Upd

Meaning: 1)SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH
Whether the RNC measures one successful handover or
relocation when receiving an Iu release command message with
the cause value "Network Optimization" from the CN during an
outgoing relocation or outgoing inter-RAT handover procedure.
1: This switch is turned on. The RNC measures one successful
handover or relocation. 0: This switch is turned off. The RNC

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D01
06
10
06
W
RF
D02
02
03
W
RF
D01
09
02
W
RF
D01
01
01
W
RF
D01
05
10
W
RF
D02
02
02
W
RF

ate
HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
r
RN
C
Soft
Han
dov
er
Inte
r
RN
C
UR
A
Upd
ate
3G
PP
R9
Spe
cifi
cati
ons
3.4/
6.8/
13.6
/27.
2Kb

Description

measures one failed handover or relocation.


2)RL_REEST_PS_ON_FACH_SWITCH Whether PS services
are established on the FACH upon call reestablishment. 1: This
switch is turned on. PS services are established on the FACH
upon a call reestablishment triggered by either of the following
factors: - All downlink radio links for a UE are out of
synchronization. - The SRB over the Uu interface is reset. 0:
This switch is turned off. PS services are established on the DCH
upon a call reestablishment triggered by either of the preceding
factors. 3)CELLUPDATE_MEASUREMENT_OPT_SWITCH
Whether the RNC repeatedly calculates the number of cell
update attempts. A UE sends a CELL UPDATE message in cell 1
and then sends another in cell 2 before receiving a CELL
UPDATE CONFIRM message from the RNC or responding to
the CELL UPDATE CONFIRM message. The UE completes the
cell update procedure in cell 2. In the preceding scenario, 1: This
switch is turned on. The RNC measures one cell update attempt
only. 0: This switch is turned off. The RNC repeatedly measures
cell update attempts.
4)D2F_PROCEDURE_OPTIMIZATION_SWITCH Whether the
optimized D2F procedure takes effect. 1: This switch is turned
on. An expired D2F procedure is considered as successful if
either of the following conditions is met: - The RB
reconfiguration message is sent in unacknowledged mode (UM),
and all the RLs in the active set receive an RL Fail indication. The RB reconfiguration message is sent in the acknowledged
mode (AM), and an ACK response is received from the UE. If
neither of the preceding conditions is met, the D2F procedure is
considered as expired. 0: This switch is turned off. The
optimized D2F procedure does not take effect. This switch is set
to 0 by default.
5)F2D_PROCEDURE_OPTIMIZATION_SWITCH Whether the
optimized F2D procedure takes effect. 1: This switch is turned
on. An expired F2D procedure is considered as successful if the
RL status is normal. If the RL status is not normal, the F2D
procedure is considered as expired. 0: This switch is turned off.
The optimized F2D procedure does not take effect. This switch is
set to 0 by default.
6)FOREVER_PCH_CTRL_PLANE_SHARE_OPT 1: This

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D01
08
01
W
RF
D01
08
02

ps
RR
C
Con
nect
ion
and
Rad
io
Acc
ess
Bea
rer
Esta
blis
hme
nt
and
Rel
ease
Intr
a
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Cell
Upd
ate
Inte
r
RN
C

Description

switch is turned on. Load sharing of UEs in the CELL_PCH state


is not triggered among SPU subsystems and the UEs in the
CELL_PCH state are periodically released on this SPU
subsystem if the following conditions are met: - The CPU usage
of the SPU subsystem exceeds a specified threshold and exceeds
the average CPU usage of the SPU subsystems under the RNC. The number of online UEs in the CELL_PCH state on this SPU
subsystem exceeds the average number of UEs in the
CELL_PCH state on the SPU subsystems under the RNC. 0:
This switch is turned off. Load sharing of UEs in the
CELL_PCH state is triggered among SPU subsystems if the
following conditions are met: - The CPU usage of the SPU
subsystem exceeds a specified threshold and exceeds the average
CPU usage of the SPU subsystems under the RNC. - The number
of online UEs in the CELL_PCH state on this SPU subsystem
exceeds the average number of UEs in the CELL_PCH state on
the SPU subsystems under the RNC.
7)FOREVER_PCH_USER_PLANE_SHARE_OPT 1: This
switch is turned on. The RNC selects another DSP to perform
load sharing on the user plane when always online users are
activated. 0: This switch is turned off. The RNC does not
perform load sharing on the user plane when always online users
are activated.
8)RAB_REL_SRV_CELL_CHG_CROSS_SWITCH Whether
the serving cell change procedure is allowed during the release
of all PS RABs. 1: This switch is turned on. The serving cell
change procedure is not allowed during the release of all PS
RABs. 0: This switch is turned off. The serving cell change
procedure is allowed during the release of all PS RABs.
9)SCRIWITHCAUSE_OVERLAP_SWITCH How the RNC will
react if it receives an SCRI message with the cause value "UE
Requested PS Data session end" in the middle of another
procedure. 1: This switch is turned on. The RNC maintains the
original RRC state and does not release the connection of the
related UE if the RNC receives an SCRI message with the
preceding cause value in the middle of another procedure. 0:
This switch is turned off. The RNC releases the connection of
the UE if both of the following conditions are met: The RNC
receives an SCRI message with the preceding cause value in the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Cell middle of another procedure. The TAC of the UE does not


Upd belong to the TACs that are enabled with fast dormancy.
ate 10)P2F_CUC_REPEAT_SWITCH Whether the RNC retransmits
a CELL UPDATE CONFIRM message to a UE that is
transitioning from the CELL_PCH or URA_PCH state to the
CELL_FACH state. 1: This switch is turned on. The RNC
retransmits a CELL UPDATE CONFIRM message to a UE that
is transitioning from the CELL_PCH or URA_PCH state to the
CELL_FACH state. 0: This switch is turned off. The RNC does
not retransmit a CELL UPDATE CONFIRM message to a UE
that is transitioning from the CELL_PCH or URA_PCH state to
the CELL_FACH state.
11)UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH
Whether to notify the NodeB of the abnormal RL release due to
poor Uu interface quality. 1: This switch is turned on. The RNC
notifies the NodeB of the abnormal RL release due to poor Uu
interface quality. 0: This switch is turned off. The RNC does not
notify the NodeB of the abnormal RL release due to poor Uu
interface quality.
12)D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH
Whether the RNC considers the D2F state transition as
successful if the RNC does not receive a response message from
the UE within the specified period after sending a RADIO
BEARER RECONFIGURTION message to the UE in
acknowledged mode (AM). 1: This switch is turned on. The
RNC considers the D2F state transition as successful if the
following conditions are met: The RNC does not receive a
response from the UE within the specified period after sending a
RADIO BEARER RECONFIGURATION message to the UE in
AM. All radio links (RLs) for the UE are out of synchronization.
The RLCs for all TRBs are in AM. If any of the preceding
conditions is not met, the RNC undoes the D2F state transition.
0: This switch is turned off. The RNC undoes the D2F state
transition if the RNC does not receive a response from the UE
within the specified period after sending a RADIO BEARER
RECONFIGURATION message to the UE in AM.
13)AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH
(Response Timer Optimization Switch for D2F and F2D
Procedures in AM) Length policy for the timer set for the RNC

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

to wait for a response message from the UE after the RNC sends
a RADIO BEARER RECONFIGURATION message to the UE
in AM during the D2F and F2D state transitions. 1: This switch
is turned on. The length of the timer equals its configured value
(value of the "RbRecfgRspTmr" parameter in the "SET
USTATETIMER" command) plus four seconds. 0: This switch is
turned off. The length of this timer equals its configured value.
14)D2P_DT_MSG_BUFFER_SWITCH (DT Message Buffer
Switch During D2P) Whether the RNC buffers the DIRECT
TRANSFER message sent by the CN during the D2P state
transition. 1: This switch is turned on. The RNC buffers the
DIRECT TRANSFER message. The RNC sends a paging
message to the UE after the D2P state transition is complete and
then sends the buffered DIRECT TRANSFER message to the
UE. 0: This switch is turned off. The RNC forwards the DIRECT
TRANSFER message to the UE immediately after receiving it.
15)CM_CODE_CONFLICT_OPT_SWITCH Used to solve code
resource conflicts in compressed mode. 1: This switch is turned
on. Code resource conflicts in compressed mode are solved. 0:
This switch is turned off. Code resource conflicts in compressed
mode are not solved.
16)H_SERV_CELL_CHANGE_MSG_OPT_SWITCH(Enable H
Serving Cell Change MSG Size Reduction) Whether to reduce
the size of the HSDPA serving cell change message. 1: This
switch is turned on. The size of the HSDPA serving cell change
message is reduced. 0: This switch is turned off. The size of the
HSDPA serving cell change message is not reduced.
17)FAST_HSDPA_SERV_CELL_CHANGE_SWITCH (Fast
HSDPA Serving Cell Change Optimization Switch) Whether to
enable the fast HSDPA serving cell change optimization
function. 1: This switch is turned on. The RNC includes the IE
Delay restriction flag in the PHYSICAL CHANNEL
RECONFIGURATION message. For details about the IE Delay
restriction flag, see section 10.2.22 in 3GPP TS25.331. 0: This
switch is turned off. The RNC does not include the IE Delay
restriction flag in the PHYSICAL CHANNEL
RECONFIGURATION message.
18)RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH(S
HO Counting Correction Switch in RL Reestablish) When the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RL reestablishment function is enabled, a soft handover


procedure is considered as successful even if the ASU CMP
message is not received if RL reestablishment is triggered during
the soft handover. This parameter specifies whether to correct the
counting of successful soft handovers when RL reestablishment
is triggered during the soft handover. 1: This switch is turned on.
Such a soft handover procedure is considered as failed. 0: This
switch is turned off. Such a soft handover procedure is
considered as successful.
19)COUNT_STATE_CHG_BY_RAB_EHN_SWITCH Whether
to enable certain state transition-related counters to be
incremented on a PS RAB basis. These counters include the
VS.DCCC.P2D.Att, VS.DCCC.P2D.Succ, VS.DCCC.Att.D2U,
and VS.DCCC.Succ.D2U counters. 1: This switch is turned on.
These counters are incremented on a PS RAB basis. 0: This
switch is turned off. These counters are incremented on a UE
basis. 20)RAB_RELATED_COUNTER_OPT_SWITCH(RAB
Setup Failure Statistical Optimization Switch) Whether to
optimize the statistics of counters measuring RAB setup failures
and abnormal RAB releases. 1: This switch is turned on. Under
this circumstance, the statistics of counters measuring RAB
setup failures and abnormal RAB releases are optimized. 0: This
switch is turned off. Under this circumstance, the statistics of
counters measuring RAB setup failures and abnormal RAB
releases are not optimized.
21)CELLUPDATE_PROCEDURE_OPT_SWITCH (Cell
Update Procedure Optimization Switch) Whether to enable the
optimized processing for the cell update procedure. 1: This
switch is set to on. The RNC supports the overlapping of these
two procedures: cell update procedure caused by RL failure and
P2D/D2P/D2F state transition procedure. For UEs in the
CELL_DCH state, the RNC performs a cell update procedure
based on the retransmitted CELL UPDATE message if the
retransmitted message carries an SRB or TRB reset indication.
For UEs in the CELL_PCH or URA_PCH state, when the
number of CELL UPDATE messages with the cause value
paging response or UL data transmission exceeds the value
specified by N381, the RNC sends an RRC connection release
message to the UE in the cell where the UE sends the last CELL

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UPDATE message. For UEs in states other than CELL_DCH or


in the middle of state transitions other than P2D, if the SRNC
receives a CELL UPDATE message with HRNTI from a UE
through the DRNC while waiting for the UE's response to the
CELL UPDATE CONFIRM message, the SRNC considers the
message as a retransmitted one. 0. This switch is set to off. The
optimized processing for the cell update procedure is not
supported. 22)PTT_PAGING_PRD_CRRCT_SWITCH(Correct
the Paging Retransmission for PTT Services over Uu) Whether
to correct the retransmission period of paging messages for push
to talk (PTT) services over the Uu interface. 1: This switch is set
to on, the retransmission period of PTT services is corrected.
That is, if the RNC does not receive a paging response within
320 ms after sending a paging message, the RNC retransmits the
paging message. 0: This switch is set to off, the retransmission
period of PTT services is not corrected. That is, the RNC
retransmits a paging message only when it does not receive a
paging response within 640 ms after sending a paging message.
23)RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH
(Respond to RAB Assignment Request upon RRC Release)
Whether the RNC processes the RAB ASSIGNMENT
REQUEST message and returns a RAB ASSIGNMENT
RESPONSE message to the CN in the following scenario: After
receiving a RAB RELEASE REQUEST message from the RNC
to release the last RAB of a UE, the CN does not return an IU
RELEASE COMMAND message but returns a RAB
ASSIGNMENT REQUEST instead. 1: This switch is set to on.
The RNC processes the RAB ASSIGNMENT REQUEST
message and returns a RAB ASSIGNMENT RESPONSE
message to the CN in the preceding scenario. 0: This switch is
set to off. The RNC does not process the RAB ASSIGNMENT
REQUEST message in the preceding scenario.
24)L2U_UP_DELAY_OPT_SWITCH (L2U UP Delay
Optimization Switch) Whether the RNC returns a
RELOCATION COMPLETE message to the CN to start UP data
transmission immediately after receiving a HANDOVER TO
UTRAN COMPLETE message during a LTE-to-UMTS
handover. 1: This switch is set to on. The RNC immediately
returns a RELOCATION COMPLETE message to the CN in the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

preceding scenario. 0: This switch is set to off. After the RNC


queries the UE's capability and the security mode procedure is
complete, the RNC returns a RELOCATION COMPLETE
message to the CN.
25)PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH
(Optimize UE Selection for Outgoing Inter-RAT Handover in
Basic Congestion) Whether the LDR algorithm on the RNC side
updates the attribute of outgoing inter-RAT handover for a UE
after an F2D, P2D, or D2D state transition procedure. 1: This
switch is set to on. The LDR algorithm on the RNC side updates
the attribute of outgoing inter-RAT handover for a UE after an
F2D, P2D, or D2D state transition procedure. In this way, the
LDR algorithm on the RNC side can select appropriate UEs for
outgoing inter-RAT handovers when the cell is in basic
congestion state. 0: This switch is set to off. The LDR algorithm
on the RNC side does not update the attribute of outgoing interRAT handover for a UE after an F2D, P2D, or D2D state
transition procedure.
GUI Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH(SYS_RELO
C_OUT_SUCC_STAT_OPT_SWITCH),
RL_REEST_PS_ON_FACH_SWITCH(RL_REEST_PS_ON_F
ACH_SWITCH),
CELLUPDATE_MEASUREMENT_OPT_SWITCH(CELLUPD
ATE_MEASUREMENT_OPT_SWITCH),
D2F_PROCEDURE_OPTIMIZATION_SWITCH(D2F_PROCE
DURE_OPTIMIZATION_SWITCH),
F2D_PROCEDURE_OPTIMIZATION_SWITCH(F2D_PROCE
DURE_OPTIMIZATION_SWITCH),
FOREVER_PCH_CTRL_PLANE_SHARE_OPT(FOREVER_P
CH_CTRL_PLANE_SHARE_OPT),
FOREVER_PCH_USER_PLANE_SHARE_OPT(FOREVER_P
CH_USER_PLANE_SHARE_OPT),
RAB_REL_SRV_CELL_CHG_CROSS_SWITCH(RAB_REL_
SRV_CELL_CHG_CROSS_SWITCH),
SCRIWITHCAUSE_OVERLAP_SWITCH(SCRIWITHCAUSE
_OVERLAP_SWITCH),
P2F_CUC_REPEAT_SWITCH(P2F_CUC_REPEAT_SWITCH)
,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH(UU_ABN
_REL_INFO_NOTIFY_NODEB_SWITCH),
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH(D2F_A
M_PROCEDURE_OPTIMIZATION_SWITCH),
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH(AM_D
2F_F2D_RESTMR_OPTIMIZATION_SWITCH),
D2P_DT_MSG_BUFFER_SWITCH(D2P_DT_MSG_BUFFER
_SWITCH),
CM_CODE_CONFLICT_OPT_SWITCH(CM_CODE_CONFLI
CT_OPT_SWITCH),
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH(H_SERV_C
ELL_CHANGE_MSG_OPT_SWITCH),
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH(FAST_HS
DPA_SERV_CELL_CHANGE_SWITCH),
RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH(RL
RST_ASU_SUCC_COUNTERS_CORRECT_SWITCH),
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH(COUNT_S
TATE_CHG_BY_RAB_EHN_SWITCH),
RAB_RELATED_COUNTER_OPT_SWITCH(RAB_RELATE
D_COUNTER_OPT_SWITCH),
CELLUPDATE_PROCEDURE_OPT_SWITCH(CELLUPDATE
_PROCEDURE_OPT_SWITCH),
PTT_PAGING_PRD_CRRCT_SWITCH(PTT_PAGING_PRD_
CRRCT_SWITCH),
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH(RRC_R
EL_STATUS_RSP_RAB_ASS_REQ_SWITCH),
L2U_UP_DELAY_OPT_SWITCH(L2U_UP_DELAY_OPT_S
WITCH),
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH(PRI_
LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH)
Unit: None
Actual Value Range:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH,
RL_REEST_PS_ON_FACH_SWITCH,
CELLUPDATE_MEASUREMENT_OPT_SWITCH,
D2F_PROCEDURE_OPTIMIZATION_SWITCH,
F2D_PROCEDURE_OPTIMIZATION_SWITCH,
FOREVER_PCH_CTRL_PLANE_SHARE_OPT,
FOREVER_PCH_USER_PLANE_SHARE_OPT,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RAB_REL_SRV_CELL_CHG_CROSS_SWITCH,
SCRIWITHCAUSE_OVERLAP_SWITCH,
P2F_CUC_REPEAT_SWITCH,
UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH,
D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH,
AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH,
D2P_DT_MSG_BUFFER_SWITCH,
CM_CODE_CONFLICT_OPT_SWITCH,
H_SERV_CELL_CHANGE_MSG_OPT_SWITCH,
FAST_HSDPA_SERV_CELL_CHANGE_SWITCH,
RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH,
COUNT_STATE_CHG_BY_RAB_EHN_SWITCH,
RAB_RELATED_COUNTER_OPT_SWITCH,
CELLUPDATE_PROCEDURE_OPT_SWITCH,
PTT_PAGING_PRD_CRRCT_SWITCH,
RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH,
L2U_UP_DELAY_OPT_SWITCH,
PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH
Default Value:
SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH:1,RL_REES
T_PS_ON_FACH_SWITCH:0,CELLUPDATE_MEASUREME
NT_OPT_SWITCH:0,D2F_PROCEDURE_OPTIMIZATION_S
WITCH:0,F2D_PROCEDURE_OPTIMIZATION_SWITCH:0,F
OREVER_PCH_CTRL_PLANE_SHARE_OPT:0,FOREVER_P
CH_USER_PLANE_SHARE_OPT:0,RAB_REL_SRV_CELL_
CHG_CROSS_SWITCH:0,SCRIWITHCAUSE_OVERLAP_S
WITCH:0,P2F_CUC_REPEAT_SWITCH:0,UU_ABN_REL_IN
FO_NOTIFY_NODEB_SWITCH:0,D2F_AM_PROCEDURE_
OPTIMIZATION_SWITCH:0,AM_D2F_F2D_RESTMR_OPTI
MIZATION_SWITCH:0,D2P_DT_MSG_BUFFER_SWITCH:0,
CM_CODE_CONFLICT_OPT_SWITCH:1,H_SERV_CELL_C
HANGE_MSG_OPT_SWITCH:0,FAST_HSDPA_SERV_CELL
_CHANGE_SWITCH:0,RLRST_ASU_SUCC_COUNTERS_C
ORRECT_SWITCH:0,COUNT_STATE_CHG_BY_RAB_EHN
_SWITCH:0,RAB_RELATED_COUNTER_OPT_SWITCH:0,C
ELLUPDATE_PROCEDURE_OPT_SWITCH:1,PTT_PAGING
_PRD_CRRCT_SWITCH:0,RRC_REL_STATUS_RSP_RAB_A
SS_REQ_SWITCH:0,L2U_UP_DELAY_OPT_SWITCH:1,PRI
_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CsHo
PrioM
easTi
merLe
n

B
S
C
6
9
0
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Interval between an inter-frequency measurement


control message for CS services and an inter-RAT measurement
control message for CS services. When a UE in compressed
mode is processing a CS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

CsHo
PrioM
easTi
merLe
n

B
S
C
6
9
1
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO

W
RF
D02
03
02
W
RF
D-

Inte
r
Fre
que
ncy
Har
d
Han
dov

Meaning: Interval between an inter-frequency measurement


control message for CS services and an inter-RAT measurement
control message for CS services. When a UE in compressed
mode is processing a CS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

PsHoP
rioMe
asTim
erLen

B
S
C
6
9
0
0

Description

MM

02 er
03 Bas
03 ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

signal quality of inter-RAT neighboring cells. When this


parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D02
03
02
W
RF
D02
03
03

Meaning: Interval between an inter-frequency measurement


control message for PS services and an inter-RAT measurement
control message for PS services. When a UE in compressed
mode is processing a PS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r-

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PsHoP
rioMe
asTim
erLen

B
S
C
6
9
1
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov

Meaning: Interval between an inter-frequency measurement


control message for PS services and an inter-RAT measurement
control message for PS services. When a UE in compressed
mode is processing a PS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag
e
CsBSI
CVerif
yIndic
ation

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa

Meaning: Whether to perform initial BSIC identification or


BSIC reconfirmation during inter-RAT signal quality
measurement for CS services.
GUI Value Range: BSICINIT_AND_RECONFIRM, BSICINIT
Unit: None
Actual Value Range: BSICINIT_AND_RECONFIRM,
BSICINIT
Default Value: BSICINIT_AND_RECONFIRM

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
CsBSI
CVerif
yIndic
ation

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
r-

Meaning: Whether to perform initial BSIC identification or


BSIC reconfirmation during inter-RAT signal quality
measurement for CS services.
GUI Value Range: BSICINIT_AND_RECONFIRM, BSICINIT
Unit: None
Actual Value Range: BSICINIT_AND_RECONFIRM,
BSICINIT
Default Value: BSICINIT_AND_RECONFIRM

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
PsBSI
CVerif
yIndic
ation

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han

Meaning: Whether to perform initial BSIC identification or


BSIC reconfirmation during inter-RAT signal quality
measurement for PS services.
GUI Value Range: BSICINIT_AND_RECONFIRM, BSICINIT,
BSICINIT_ADPT
Unit: None
Actual Value Range: BSICINIT_AND_RECONFIRM,
BSICINIT, BSICINIT_ADPT
Default Value: BSICINIT_AND_RECONFIRM

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

PsBSI
CVerif
yIndic
ation

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE

W
RF
D02
04
02

dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

W
RF
D02
03
03
W
RF
D-

Inte
rRA
T
Han
dov
er
Bas
ed

Description

Meaning: Whether to perform initial BSIC identification or


BSIC reconfirmation during inter-RAT signal quality
measurement for PS services.
GUI Value Range: BSICINIT_AND_RECONFIRM, BSICINIT,
BSICINIT_ADPT
Unit: None
Actual Value Range: BSICINIT_AND_RECONFIRM,
BSICINIT, BSICINIT_ADPT

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
LLIN
TERR
ATH
OCO
V

02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

Description

on Default Value: BSICINIT_AND_RECONFIRM


Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RrcRs
cpPeri
odTim
er

B
S
C
6
9
0
0

SET
UCH
LQU
ALIT
YEV
ALU
ATE

W
RF
D01
06
90

TTI
Swi
tch
for
BE
Ser
vice
s
Bas
ed
on
Cov
erag
e

Meaning: Interval for UEs to report the RSCP during the interval
between RRC connection setup and RAB assignment
GUI Value Range: D250, D500, D1000, D2000, D3000, D4000,
D6000, D8000, D12000, D16000, D20000, D24000, D28000,
D32000, D64000
Unit: ms
Actual Value Range: 250, 500, 1000, 2000, 3000, 4000, 6000,
8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Default Value: D500

RrcRs
cpPeri
odTim
er

B
S
C
6
9
1
0

SET
UCH
LQU
ALIT
YEV
ALU
ATE

W
RF
D01
06
90

TTI
Swi
tch
for
BE
Ser
vice
s
Bas
ed
on
Cov
erag
e

Meaning: Interval for UEs to report the RSCP during the interval
between RRC connection setup and RAB assignment
GUI Value Range: D250, D500, D1000, D2000, D3000, D4000,
D6000, D8000, D12000, D16000, D20000, D24000, D28000,
D32000, D64000
Unit: ms
Actual Value Range: 250, 500, 1000, 2000, 3000, 4000, 6000,
8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Default Value: D500

RabRs
cpPeri
odTim
er

B
S
C
6
9
0
0

SET
UCH
LQU
ALIT
YEV
ALU
ATE

W
RF
D01
06
90

TTI
Swi
tch
for
BE
Ser
vice
s
Bas

Meaning: Interval for UEs to report the RSCP after a service


setup.
GUI Value Range: D250, D500, D1000, D2000, D3000, D4000,
D6000, D8000, D12000, D16000, D20000, D24000, D28000,
D32000, D64000
Unit: ms
Actual Value Range: 250, 500, 1000, 2000, 3000, 4000, 6000,
8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Default Value: D2000

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ed
on
Cov
erag
e
RabRs
cpPeri
odTim
er

B
S
C
6
9
1
0

SET
UCH
LQU
ALIT
YEV
ALU
ATE

W
RF
D01
06
90

TTI
Swi
tch
for
BE
Ser
vice
s
Bas
ed
on
Cov
erag
e

Meaning: Interval for UEs to report the RSCP after a service


setup.
GUI Value Range: D250, D500, D1000, D2000, D3000, D4000,
D6000, D8000, D12000, D16000, D20000, D24000, D28000,
D32000, D64000
Unit: ms
Actual Value Range: 250, 500, 1000, 2000, 3000, 4000, 6000,
8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Default Value: D2000

Interfr B ADD
eqMc S UCE
Mode C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether to measure the signal quality of interfrequency neighboring cells in batches. When this switch is
turned on, the RNC instructs UEs to preferentially measure the
signal quality of up to two frequencies with high coverage-based
inter-frequency handover priorities. If the measurement expires,
these UEs stop the measurement on these frequencies and start
the measurement on the other frequencies based on their
coverage-based inter-frequency handover priorities. The higher
the priority of a frequency is, the more likely the signal quality
of the frequency is measured. In each batch, up to two
frequencies are involved. When this switch is turned off, the
RNC instructs UEs to measure the signal quality of only up to
two frequencies with high coverage-based inter-frequency
handover priorities. A maximum of 32 inter-frequency
neighboring cells can be involved in a measurement, regardless
of whether this switch is turned on or off. For example, there are
five inter-frequency neighboring cells (cells 1 through 5). As for
frequencies, cells 1 and 2 use frequency a, and cells 3 through 5

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

use frequencies b through d, respectively. As for coverage-based


inter-frequency handover priorities, the priority of cells 1 and 2
is high, that of cell 3 is middle, and that of cells 4 and 5 is low.
When this switch is turned on, a UE preferentially starts a
measurement in cells 1 through 3. If the measurement expires,
the UE starts a measurement in cells 4 and 5. When this switch is
turned off, the UE performs a measurement in only cells 1
through 3.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF
Interfr B ADD
eqMc S UCE
Mode C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether to measure the signal quality of interfrequency neighboring cells in batches. When this switch is
turned on, the RNC instructs UEs to preferentially measure the
signal quality of up to two frequencies with high coverage-based
inter-frequency handover priorities. If the measurement expires,
these UEs stop the measurement on these frequencies and start
the measurement on the other frequencies based on their
coverage-based inter-frequency handover priorities. The higher
the priority of a frequency is, the more likely the signal quality
of the frequency is measured. In each batch, up to two
frequencies are involved. When this switch is turned off, the
RNC instructs UEs to measure the signal quality of only up to
two frequencies with high coverage-based inter-frequency
handover priorities. A maximum of 32 inter-frequency
neighboring cells can be involved in a measurement, regardless
of whether this switch is turned on or off. For example, there are
five inter-frequency neighboring cells (cells 1 through 5). As for
frequencies, cells 1 and 2 use frequency a, and cells 3 through 5
use frequencies b through d, respectively. As for coverage-based
inter-frequency handover priorities, the priority of cells 1 and 2
is high, that of cell 3 is middle, and that of cells 4 and 5 is low.
When this switch is turned on, a UE preferentially starts a
measurement in cells 1 through 3. If the measurement expires,
the UE starts a measurement in cells 4 and 5. When this switch is
turned off, the UE performs a measurement in only cells 1
through 3.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

GUI Value Range: OFF, ON


Unit: None
Actual Value Range: OFF, ON
Default Value: OFF
InterF
reqHO
Consi
derRT
WPS
w

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether the RNC considers the RTWP of the target


cell when performing coverage-based inter-frequency handovers.
When this switch is set to on, the RNC performs coverage-based
inter-frequency handovers only when the uplink coverage
(RTWP) of the target cell meets certain conditions. When this
switch is set to off, the RNC does not consider the uplink
coverage of the target cell when performing coverage-based
inter-frequency handovers.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: ON, OFF
Default Value: OFF

InterF
reqHO
Consi
derRT
WPS
w

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether the RNC considers the RTWP of the target


cell when performing coverage-based inter-frequency handovers.
When this switch is set to on, the RNC performs coverage-based
inter-frequency handovers only when the uplink coverage
(RTWP) of the target cell meets certain conditions. When this
switch is set to off, the RNC does not consider the uplink
coverage of the target cell when performing coverage-based
inter-frequency handovers.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: ON, OFF
Default Value: OFF

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
PROC
ESSS
WITC
H5

B
S
C
6
9
0
0

SET
URR
CTRL
SWIT
CH

W
RF
D15
02
52
W
RF
D15
02
53
M
RF
D09
02
11
W
RF
D15
02
54
W
RF
D15
02
55

Vid
eo
Paci
ng
VoI
P
App
licat
ion
Ma
nag
eme
nt
Diff
eren
tiate
d
Ser
vice
Bas
ed
on
App
licat
ion
Res
our
ce
Res
erva
tion
Diff
eren
tiate
d
Ser
vice
Bas
ed

Description

Meaning:
1)INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH(RI
M-based and Request-based Load Information Sharing Switch)
Whether a UMTS cell sends its load information to an LTE cell
through the RIM procedure after receiving a load information
sharing request from the LTE cell. 1: This switch is turned on.
UMTS cells support the RIM-based load information sharing
function. A UMTS cell sends its load information to an LTE cell
after receiving a load information sharing request from the LTE
cell. 0: This switch is turned off. UMTS cells do not support the
RIM-based load information sharing function. A UMTS cell does
not respond to the load information sharing request from an LTE
cell.
2)INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH(Learni
ng LTE Load Through RIM Switch) Whether the RNC obtains
the load information about LTE cells through the RAN
information management (RIM) procedure. For details about the
RIM procedure, see 3GPP TS 48. 018. 1: This switch is turned
on. The RNC obtains the load information about LTE cells
through the RIM procedure. 0: This switch is turned off. The
RNC cannot obtain the load information about LTE cells through
the RIM procedure. 3)UL_EVQI_SWITCH(UL EVQI
Evaluation Switch) Whether to enable the EVQI function in the
uplink. 1: This switch is turned on. EVQI is enabled in the
uplink. 0: This switch is turned off. EVQI is disabled in the
uplink. 4)DL_EVQI_SWITCH(DL EVQI Evaluation Switch)
Whether to enable the EVQI function in the downlink. 1: This
switch is turned on. EVQI is enabled in the downlink. 0: This
switch is turned off. EVQI is disabled in the downlink. 5)
VIDEO_RATE_ADAPTION_SWITCH (Video Service Rate
Adaption Switch) Whether the Video Service Rate Adaption
feature is enabled. 1: This switch is turned on. The Video Service
Rate Adaption feature is enabled for PS UEs processing video
services. That is, the rate of video service is ensured or is limited
for these PS UEs. 0: This switch is turned off. The Video Service
Rate Adaption feature is disabled for PS UEs. 6)
VOIP_MANAGE_SWITCH (VoIP Application Management
Switch) Whether the VoIP application management function is
enabled. 1: This switch is turned on. VoIP application

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
on
Ter
min
al

Description

management actions are performed on PS UEs that are


processing VoIP services. VoIP application management actions
can either be VoIP application rate ensurance or VoIP application
speed limit. 0: This switch is turned off. the VoIP application
management function is disabled for PS UEs. 7)
DIFF_SERVICE_ON_TERMINAL_SWITCH (Differentiated
Service Based on Terminal Switch) Whether the Differentiated
Service Based on Terminal feature is enabled. 1: This switch is
turned on. PS UEs processing BE services are grouped into
different terminal groups based on their type approval codes
(TACs) in IMEIs, and each terminal group is assigned an SPI
weight for BE services, thereby achieving differentiated services.
0: This switch is turned off. The Differentiated Service Based on
Terminal feature is disabled for PS UEs processing BE services.
8) APP_GRP_RES_RSV_SWITCH (Differentiated Service
Based on Application Resource Reservation Switch) Whether the
Differentiated Service Based on Application Resource
Reservation feature is enabled. 1: This switch is turned on. The
RNC identifies service types, maps different service types to
different resource groups, and configure different resource
reservation policies for these resource groups. In this way,
resource reservation is performed based on service types. 0: This
switch is turned off. The RNC does not reserve resources based
on service types or service groups.
9)RIM_ON_ECO_SWITCH(Support RIM by eCoordinator
Switch) Whether the RIM procedure is implemented through the
eCoordinator. 1: This switch is turned on. The RIM procedure is
implemented through the eCoordinator. 0: This switch is turned
off. the RIM procedure is implemented through the CN. This
parameter is an advanced parameter. Therefore, modify the
setting of this parameter under the instruction of Huawei
technical support.
10)SRBCHG_DRD_FAST_RB_SETUP_SWITCH(RB Fast
Setup Switch for RB Setups Accompanied by DRDs with
Changing SRBs) Whether to use the RB fast setup function for
RB setups accompanied by DRDs with changing SRBs. 1: This
switch is turned on. The RB fast setup function is used for RB
setups accompanied by DRDs with changing SRBs. 0: This
switch is turned off. The simultaneous setup procedure is used

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

for RB setups accompanied by DRDs with changing SRBs.


11)SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH(RB Fast
Setup Switch for RB Setups Accompanied by DRDs with
Unchanged SRBs) Whether to use the RB fast setup function for
RB setups accompanied by DRDs with unchanged SRBs. 1: This
switch is turned on. The RB fast setup function is used for RB
setups accompanied by DRDs with unchanged SRBs. 0: This
switch is turned off. The simultaneous setup procedure is used
for RB setups accompanied by DRDs with unchanged SRBs.
12)FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH
Whether the RNC releases a UE's RRC connection after an RB
reconfiguration failure with the cause of
"incompatibleSimultaneousReconfiguration" or "invalid
configuration." This switch is set to off by default. 1: This switch
is turned on. The RNC releases the UE's RRC connection. 0:
This switch is turned off. The RNC does not release the UE's
RRC connection and rolls back the procedure.
13)WBAMR_HHO_FAIL_ROLLBACK_SWITCH Whether
RNC performs rollback operations when AMR-WB services
experience hard handover failures. 1: This switch is turned on.
The RNC performs rollback operations when AMR-WB services
experience hard handover failures. Before setting this switch to
ON, you are advised to run the "SET UCONNMODETIMER"
command to set T312 to 1s. Otherwise, some UEs experience
garbled noise. 0: This switch is turned off. The RNC does not
perform rollback operations when AMR-WB services experience
hard handover failures, and UEs experience call drops.
GUI Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH,
UL_EVQI_SWITCH, DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH,
APP_GRP_RES_RSV_SWITCH, RIM_ON_ECO_SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWITCH,
SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH,
UL_EVQI_SWITCH, DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH,
APP_GRP_RES_RSV_SWITCH, RIM_ON_ECO_SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWITCH,
SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH:0,IN
TERRAT_LOAD_REPORT_FROM_LTE_SWITCH:0,UL_EVQ
I_SWITCH:0,DL_EVQI_SWITCH:0,VIDEO_RATE_ADAPTI
ON_SWITCH:0,VOIP_MANAGE_SWITCH:0,DIFF_SERVICE
_ON_TERMINAL_SWITCH:0,APP_GRP_RES_RSV_SWITC
H:0,RIM_ON_ECO_SWITCH:0,SRBCHG_DRD_FAST_RB_S
ETUP_SWITCH:0,SRBNOCHG_DRD_FAST_RB_SETUP_SW
ITCH:0,FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH:0
,WBAMR_HHO_FAIL_ROLLBACK_SWITCH:0
PROC
ESSS
WITC
H5

B
S
C
6
9
1
0

SET
URR
CTRL
SWIT
CH

W
RF
D15
02
52
W
RF
D15
02
53
M
RF
D-

Vid
eo
Paci
ng
VoI
P
App
licat
ion
Ma
nag
eme
nt
Diff
eren

Meaning:
1)INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH(RI
M-based and Request-based Load Information Sharing Switch)
Whether a UMTS cell sends its load information to an LTE cell
through the RIM procedure after receiving a load information
sharing request from the LTE cell. 1: This switch is turned on.
UMTS cells support the RIM-based load information sharing
function. A UMTS cell sends its load information to an LTE cell
after receiving a load information sharing request from the LTE
cell. 0: This switch is turned off. UMTS cells do not support the
RIM-based load information sharing function. A UMTS cell does
not respond to the load information sharing request from an LTE
cell.
2)INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH(Learni
ng LTE Load Through RIM Switch) Whether the RNC obtains

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
09
02
11
W
RF
D15
02
54
W
RF
D15
02
55

tiate
d
Ser
vice
Bas
ed
on
App
licat
ion
Res
our
ce
Res
erva
tion
Diff
eren
tiate
d
Ser
vice
Bas
ed
on
Ter
min
al

Description

the load information about LTE cells through the RAN


information management (RIM) procedure. For details about the
RIM procedure, see 3GPP TS 48. 018. 1: This switch is turned
on. The RNC obtains the load information about LTE cells
through the RIM procedure. 0: This switch is turned off. The
RNC cannot obtain the load information about LTE cells through
the RIM procedure. 3)UL_EVQI_SWITCH(UL EVQI
Evaluation Switch) Whether to enable the EVQI function in the
uplink. 1: This switch is turned on. EVQI is enabled in the
uplink. 0: This switch is turned off. EVQI is disabled in the
uplink. 4)DL_EVQI_SWITCH(DL EVQI Evaluation Switch)
Whether to enable the EVQI function in the downlink. 1: This
switch is turned on. EVQI is enabled in the downlink. 0: This
switch is turned off. EVQI is disabled in the downlink. 5)
VIDEO_RATE_ADAPTION_SWITCH (Video Service Rate
Adaption Switch) Whether the Video Service Rate Adaption
feature is enabled. 1: This switch is turned on. The Video Service
Rate Adaption feature is enabled for PS UEs processing video
services. That is, the rate of video service is ensured or is limited
for these PS UEs. 0: This switch is turned off. The Video Service
Rate Adaption feature is disabled for PS UEs. 6)
VOIP_MANAGE_SWITCH (VoIP Application Management
Switch) Whether the VoIP application management function is
enabled. 1: This switch is turned on. VoIP application
management actions are performed on PS UEs that are
processing VoIP services. VoIP application management actions
can either be VoIP application rate ensurance or VoIP application
speed limit. 0: This switch is turned off. the VoIP application
management function is disabled for PS UEs. 7)
DIFF_SERVICE_ON_TERMINAL_SWITCH (Differentiated
Service Based on Terminal Switch) Whether the Differentiated
Service Based on Terminal feature is enabled. 1: This switch is
turned on. PS UEs processing BE services are grouped into
different terminal groups based on their type approval codes
(TACs) in IMEIs, and each terminal group is assigned an SPI
weight for BE services, thereby achieving differentiated services.
0: This switch is turned off. The Differentiated Service Based on
Terminal feature is disabled for PS UEs processing BE services.
8) APP_GRP_RES_RSV_SWITCH (Differentiated Service

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Based on Application Resource Reservation Switch) Whether the


Differentiated Service Based on Application Resource
Reservation feature is enabled. 1: This switch is turned on. The
RNC identifies service types, maps different service types to
different resource groups, and configure different resource
reservation policies for these resource groups. In this way,
resource reservation is performed based on service types. 0: This
switch is turned off. The RNC does not reserve resources based
on service types or service groups.
9)RIM_ON_ECO_SWITCH(Support RIM by eCoordinator
Switch) Whether the RIM procedure is implemented through the
eCoordinator. 1: This switch is turned on. The RIM procedure is
implemented through the eCoordinator. 0: This switch is turned
off. the RIM procedure is implemented through the CN. This
parameter is an advanced parameter. Therefore, modify the
setting of this parameter under the instruction of Huawei
technical support.
10)SRBCHG_DRD_FAST_RB_SETUP_SWITCH(RB Fast
Setup Switch for RB Setups Accompanied by DRDs with
Changing SRBs) Whether to use the RB fast setup function for
RB setups accompanied by DRDs with changing SRBs. 1: This
switch is turned on. The RB fast setup function is used for RB
setups accompanied by DRDs with changing SRBs. 0: This
switch is turned off. The simultaneous setup procedure is used
for RB setups accompanied by DRDs with changing SRBs.
11)SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH(RB Fast
Setup Switch for RB Setups Accompanied by DRDs with
Unchanged SRBs) Whether to use the RB fast setup function for
RB setups accompanied by DRDs with unchanged SRBs. 1: This
switch is turned on. The RB fast setup function is used for RB
setups accompanied by DRDs with unchanged SRBs. 0: This
switch is turned off. The simultaneous setup procedure is used
for RB setups accompanied by DRDs with unchanged SRBs.
12)FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH
Whether the RNC releases a UE's RRC connection after an RB
reconfiguration failure with the cause of
"incompatibleSimultaneousReconfiguration" or "invalid
configuration." This switch is set to off by default. 1: This switch
is turned on. The RNC releases the UE's RRC connection. 0:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

This switch is turned off. The RNC does not release the UE's
RRC connection and rolls back the procedure.
13)WBAMR_HHO_FAIL_ROLLBACK_SWITCH Whether
RNC performs rollback operations when AMR-WB services
experience hard handover failures. 1: This switch is turned on.
The RNC performs rollback operations when AMR-WB services
experience hard handover failures. Before setting this switch to
ON, you are advised to run the "SET UCONNMODETIMER"
command to set T312 to 1s. Otherwise, some UEs experience
garbled noise. 0: This switch is turned off. The RNC does not
perform rollback operations when AMR-WB services experience
hard handover failures, and UEs experience call drops.
GUI Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH,
UL_EVQI_SWITCH, DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH,
APP_GRP_RES_RSV_SWITCH, RIM_ON_ECO_SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWITCH,
SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITCH
Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH,
UL_EVQI_SWITCH, DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH,
APP_GRP_RES_RSV_SWITCH, RIM_ON_ECO_SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWITCH,
SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH:0,IN

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

TERRAT_LOAD_REPORT_FROM_LTE_SWITCH:0,UL_EVQ
I_SWITCH:0,DL_EVQI_SWITCH:0,VIDEO_RATE_ADAPTI
ON_SWITCH:0,VOIP_MANAGE_SWITCH:0,DIFF_SERVICE
_ON_TERMINAL_SWITCH:0,APP_GRP_RES_RSV_SWITC
H:0,RIM_ON_ECO_SWITCH:0,SRBCHG_DRD_FAST_RB_S
ETUP_SWITCH:0,SRBNOCHG_DRD_FAST_RB_SETUP_SW
ITCH:0,FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH:0
,WBAMR_HHO_FAIL_ROLLBACK_SWITCH:0
DivCt B SET
rlField S UHO
C COM
6 M
9
0
0

W
RF
D02
02
01
W
RF
D02
02
03
W
RF
D02
02
02

Intr
a
Nod
eB
Soft
er
Han
dov
er
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Whether the NodeB implements maximum ratio


combination. There are two combination methods for uplink
combination of soft handover: one is maximum ratio
combination on the NodeB side, which gives the highest
combination gain; the other is selective combination at the RNC,
which gives a relatively smaller combination gain. When MAY
is selected, the NodeB decides whether to implement maximum
ratio combination according to its own physical conditions.
When MUST is selected, the NodeB is forced to carry out
maximum ratio combination which is usually used in tests. In
this case, if the NodeB does not support maximum ratio
combination, link setup or adding fails. When MUST_NOT is
selected, the NodeB is forbidden to carry out maximum ratio
combination. If the NodeB does not implement maximum ratio
combination, the RNC automatically performs selective
combination.
GUI Value Range: MAY(NodeB chooses whether combine at
NodeB), MUST(Must combine at NodeB), MUST_NOT(Must
combine at RNC)
Unit: None
Actual Value Range: MAY, MUST, MUST_NOT
Default Value: MAY(NodeB chooses whether combine at
NodeB)

DivCt B SET
rlField S UHO
C COM
6 M

W
RF
D02

Intr
a
Nod
eB

Meaning: Whether the NodeB implements maximum ratio


combination. There are two combination methods for uplink
combination of soft handover: one is maximum ratio
combination on the NodeB side, which gives the highest

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

9
1
0

02
01
W
RF
D02
02
03
W
RF
D02
02
02

Soft
er
Han
dov
er
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

combination gain; the other is selective combination at the RNC,


which gives a relatively smaller combination gain. When MAY
is selected, the NodeB decides whether to implement maximum
ratio combination according to its own physical conditions.
When MUST is selected, the NodeB is forced to carry out
maximum ratio combination which is usually used in tests. In
this case, if the NodeB does not support maximum ratio
combination, link setup or adding fails. When MUST_NOT is
selected, the NodeB is forbidden to carry out maximum ratio
combination. If the NodeB does not implement maximum ratio
combination, the RNC automatically performs selective
combination.
GUI Value Range: MAY(NodeB chooses whether combine at
NodeB), MUST(Must combine at NodeB), MUST_NOT(Must
combine at RNC)
Unit: None
Actual Value Range: MAY, MUST, MUST_NOT
Default Value: MAY(NodeB chooses whether combine at
NodeB)

CmpS B SET
witch S UCO
C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D01
06
10
06
W
RF
D02
02
03
W
RF
D02

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
r
RN
C
Soft
Han
dov

Meaning: 1.
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH: When the
switch is on, the IMS signaling assigned by the CN undergoes
compatibility processing as an ordinary PS service. When the
switch is not on, no special processing is performed. 2.
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH:
When the Iu QoS Negotiation function is active and the switch is
on, IE RAB Asymmetry Indicator is Symmetric bidirectional,
The uplink and downlink RNC negotiation rate is asymmetric,
"RNC" select the bigger rate as Iu QoS negotiation rate. When
the switch is OFF, "RNC" select the less rate as Iu QoS
negotiation rate. 3.
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH: When
the switch is on, the IUUP version can be rolled back to R99
when complete configurations are applied during inter-RAT
handover. 4.
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH: When

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
02
W
RF
D15
02
09
W
RF
D15
02
27
W
RF
D02
12
00
W
RF
D15
02
23
W
RF
D01
06
96
W
RF
D01
02
02

er
Intr
a
RN
C
Soft
Han
dov
er
DBHS
DP
A
DBHS
DP
A+
MI
MO
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
MC
HS
DP
A+
MI
MO
DCHS

Description

the switch is on, H2D is performed before a neighboring RNC


cell whose version is earlier than R5 is added to the active set;
E2D is performed before a neighboring RNC cell whose version
is earlier than R6 is added to the active set. If the DRNC is of a
version earlier than R5, DL services cannot be mapped on the
HS-DSCH. If the DRNC is of a version earlier than R6, DL
services cannot be mapped on the HS-EDCH. 5.
CMP_IUR_SHO_DIVCTRL_SWITCH: When the switch is on,
the diversity combination over the Iur interface is configured on
the basis of that of the local RNC. When the switch is not on, the
diversity combination over the Iur interface is configured on the
basis of services. The flag of diversity combination over the Iur
interface can be set to MUST (for BE services) or MAY (for
other services). 6.
CMP_UU_ADJACENT_FREQ_CM_SWITCH: Whether the
RNC activates the compressed mode before initiating an interfrequency measurement on a DC-HSDPA or DB-HSDPA UE.
When this parameter is set to ON, the RNC initiates the interfrequency measurement without activating the compressed mode
if both the UE and EARFCN support the non-compressed interfrequency measurement. When this parameter is set to OFF, the
RNC activates the compressed mode before initiating the interfrequency measurement. This switch takes effect only in nonflexible DC cells and DB cells. 7.
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH: This
parameter specifies to enable AMR through DRD two-step
procedure function. When SRB is set up on DCH, and "RNC"
decides to setup the AMR through DRD procedure, When the
switch is enabled, "RNC" will execute blind handover to the
target cell, and then setup the AMR RBs on the target cell, When
the switch is disabled, "RNC" will setup the AMR RBs on the
target cell directly. 8.
CMP_UU_AMR_SID_MUST_CFG_SWITCH: For narrowband
AMR services, when the switch is on, the SID frame is always
configured; when the switch is not on, the SID frame is
configured on the basis of CN assignment. 9.
CMP_UU_FDPCH_COMPAT_SWITCH: When the switch is
OFF, if the information element that indicates the F-DPCH
capability of UE exists in the message "RRC_CONNECT_REQ"

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D01
06
12
04
W
RF
D14
02
04
W
RF
D15
02
50

DP
A
UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LLDC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
DCHS
UP

Description

or "RRC_CONNECT_SETUP_CMP", the F-DPCH capability


depends on that indicator. In other case, it means UE does not
support F-DPCH. When the switch is ON, if the information
element that indicates the F-DPCH capability of UE exists in the
message "RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH capability
depends on that indicator. If that information element does not
exist, UE supports F-DPCH when all the conditions meets: a) the
version of UE is Release 6. b) UE supports HS-PDSCH. 10.
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH: When the
switch is on, the RAB assignment request and the subsequent RB
setup procedure proceed if the RLC AM capabilities of the UE
fail to meet the minimum RLC TX/RX window buffer
requirement of the RAB to be setup. When the switch is not on,
the RAB assignment request is rejected. 11.
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH:
When this switch is on, the cell individual offset (CIO) of the
best cell is always set to 0 in the INTRA-FREQUENCY
MEASUREMENT CONTROL messages. Otherwise, the CIO
information of the best cell is not carried in the INTRAFREQUENCY MEASUREMENT CONTROL messages. 12.
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH:
When the switch is on, the cell synchronization information
traced by the IOS need to be reported during the RRC
measurement period. 13.
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH: When
the switch is on, the active set update is in the same procedure as
the change of the serving cell. When the switch is not on, the
serving cell is changed after the UE updates the active set and
delivers reconfiguration of physical channels. This switch is
applicable only to R6 or aboveUEs. 14.
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH:
When the switch is on, channel transition is in the same
procedure as the change of the serving cell. When the switch is
not on, the serving cell is changed after the UE performs channel
transition and delivers reconfiguration of physical channels. 15.
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH: By
default, the switch is on. In this case, the Alternative E-bit is not
configured for L2. 16.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
A
3CHS
DP
A

Description

CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH: When the


switch is set to ON, only uplink RLC or downlink RLC can be
re-established during the state transition from CELL_FACH to
CELL_FACH (F2F for short). 17.
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH: When the
switch is set to ON, only uplink RLC or downlink RLC can be
re-established during the state transition from CELL_DCH to
CELL_FACH (D2F for short). 18.
CMP_RAB_5_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 5 can be configured with the
Robust Header Compression (ROHC) function. When the switch
is set to OFF, the service with RAB ID 5 cannot be configured
with the ROHC function. 19.
CMP_RAB_6_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 6 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 6 cannot be configured with the ROHC function. 20.
CMP_RAB_7_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 7 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 7 cannot be configured with the ROHC function. 21.
CMP_RAB_8_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 8 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 8 cannot be configured with the ROHC function. 22.
CMP_RAB_9_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 9 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 9 cannot be configured with the ROHC function. 23.
CMP_HSUPA_MACD_FLOW_MUL_SWITCH: When the
switch is set to ON, MAC-d flow can be multiplexed without any
restrictions. When the switch is set to OFF, only MAC-d flows
whose scheduling priority is lower than that of the current MACd flow can be multiplexed. 24.
CMP_SMLC_RSLT_MODE_TYPE_SWITCH: If the Client
Type of a positioning request is Emergency Services, PLMN
Operator Services, PLMN Operator - broadcast services, PLMN
Operator - O&M, PLMN Operator - anonymous statistics or
PLMN Operator - Target MS service support, the positioning

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

result is reported by using the Ellipsoid point with uncertainty


circle type. For other client types, the positioning result is
reported by using the Ellipsoid Arc type. 25.
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH: Switch for
optimizing the procedure for the CELL_FACH-to-CELL_PCHor-URA_PCH state transition. When this switch is set to on, F2P
state transition is performed through the physical channel
reconfiguration procedure.When this switch is set to off, F2P
state transition is performed through the RB reconfiguration
procedure. 26.
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH: Whether to
carry parameters related to events 1A and 1D in system
information block type 11 (SIB 11) and SIB 12.If the switch of
deferred measurement control reading is turned on, the UE
cannot promptly read parameters related to events 1A and 1D for
intra-frequency neighboring cells from SIB 11 or SIB12. As a
result, the UE cannot perform soft handovers in advance. The
switch is set using DeferMcReadInd in the ADD/MOD
UCELLMEAS command.
GUI Value Range:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,
CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH
Unit: None
Actual Value Range:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,
CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH
Default Value:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH:0,CMP_I
U_QOS_ASYMMETRY_IND_COMPAT_SWITCH:0,CMP_IU
_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH:0,CMP_IUR_H2

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

D_FOR_LOWR5_NRNCCELL_SWITCH:0,CMP_IUR_SHO_
DIVCTRL_SWITCH:0,CMP_UU_ADJACENT_FREQ_CM_S
WITCH:0,CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH:1
,CMP_UU_AMR_SID_MUST_CFG_SWITCH:0,CMP_UU_FD
PCH_COMPAT_SWITCH:0,CMP_UU_IGNORE_UE_RLC_C
AP_SWITCH:1,CMP_UU_INTRA_FREQ_MC_BESTCELL_C
IO_SWITCH:0,CMP_UU_IOS_CELL_SYNC_INFO_REPORT
_SWITCH:0,CMP_UU_SERV_CELL_CHG_WITH_ASU_SWI
TCH:0,CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWI
TCH:1,CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWIT
CH:1,CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH:0,CMP
_D2F_RLC_ONESIDE_REBUILD_SWITCH:0,CMP_RAB_5_
CFG_ROHC_SWITCH:0,CMP_RAB_6_CFG_ROHC_SWITC
H:0,CMP_RAB_7_CFG_ROHC_SWITCH:0,CMP_RAB_8_CF
G_ROHC_SWITCH:0,CMP_RAB_9_CFG_ROHC_SWITCH:0,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH:0,CMP_SMLC
_RSLT_MODE_TYPE_SWITCH:0,CMP_F2P_PROCESS_OPT
IMIZATION_SWITCH:0,CMP_UU_SIB11_SIB12_WITH_1A1
D_SWITCH:0
CmpS B SET
witch S UCO
C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D01
06
10
06
W
RF
D02
02
03
W
RF
D02
02
02

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
r
RN
C
Soft
Han
dov
er
Intr

Meaning: 1.
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH: When the
switch is on, the IMS signaling assigned by the CN undergoes
compatibility processing as an ordinary PS service. When the
switch is not on, no special processing is performed. 2.
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH:
When the Iu QoS Negotiation function is active and the switch is
on, IE RAB Asymmetry Indicator is Symmetric bidirectional,
The uplink and downlink RNC negotiation rate is asymmetric,
"RNC" select the bigger rate as Iu QoS negotiation rate. When
the switch is OFF, "RNC" select the less rate as Iu QoS
negotiation rate. 3.
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH: When
the switch is on, the IUUP version can be rolled back to R99
when complete configurations are applied during inter-RAT
handover. 4.
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH: When
the switch is on, H2D is performed before a neighboring RNC
cell whose version is earlier than R5 is added to the active set;

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D15
02
09
W
RF
D15
02
27
W
RF
D02
12
00
W
RF
D15
02
23
W
RF
D01
06
96
W
RF
D01
02
02
W
RF

a
RN
C
Soft
Han
dov
er
DBHS
DP
A
DBHS
DP
A+
MI
MO
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
MC
HS
DP
A+
MI
MO
DCHS
DP
A

Description

E2D is performed before a neighboring RNC cell whose version


is earlier than R6 is added to the active set. If the DRNC is of a
version earlier than R5, DL services cannot be mapped on the
HS-DSCH. If the DRNC is of a version earlier than R6, DL
services cannot be mapped on the HS-EDCH. 5.
CMP_IUR_SHO_DIVCTRL_SWITCH: When the switch is on,
the diversity combination over the Iur interface is configured on
the basis of that of the local RNC. When the switch is not on, the
diversity combination over the Iur interface is configured on the
basis of services. The flag of diversity combination over the Iur
interface can be set to MUST (for BE services) or MAY (for
other services). 6.
CMP_UU_ADJACENT_FREQ_CM_SWITCH: Whether the
RNC activates the compressed mode before initiating an interfrequency measurement on a DC-HSDPA or DB-HSDPA UE.
When this parameter is set to ON, the RNC initiates the interfrequency measurement without activating the compressed mode
if both the UE and EARFCN support the non-compressed interfrequency measurement. When this parameter is set to OFF, the
RNC activates the compressed mode before initiating the interfrequency measurement. This switch takes effect only in nonflexible DC cells and DB cells. 7.
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH: This
parameter specifies to enable AMR through DRD two-step
procedure function. When SRB is set up on DCH, and "RNC"
decides to setup the AMR through DRD procedure, When the
switch is enabled, "RNC" will execute blind handover to the
target cell, and then setup the AMR RBs on the target cell, When
the switch is disabled, "RNC" will setup the AMR RBs on the
target cell directly. 8.
CMP_UU_AMR_SID_MUST_CFG_SWITCH: For narrowband
AMR services, when the switch is on, the SID frame is always
configured; when the switch is not on, the SID frame is
configured on the basis of CN assignment. 9.
CMP_UU_FDPCH_COMPAT_SWITCH: When the switch is
OFF, if the information element that indicates the F-DPCH
capability of UE exists in the message "RRC_CONNECT_REQ"
or "RRC_CONNECT_SETUP_CMP", the F-DPCH capability
depends on that indicator. In other case, it means UE does not

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D01
06
12
04
W
RF
D14
02
04
W
RF
D15
02
50

UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LLDC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
DCHS
UP
A
3C-

Description

support F-DPCH. When the switch is ON, if the information


element that indicates the F-DPCH capability of UE exists in the
message "RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH capability
depends on that indicator. If that information element does not
exist, UE supports F-DPCH when all the conditions meets: a) the
version of UE is Release 6. b) UE supports HS-PDSCH. 10.
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH: When the
switch is on, the RAB assignment request and the subsequent RB
setup procedure proceed if the RLC AM capabilities of the UE
fail to meet the minimum RLC TX/RX window buffer
requirement of the RAB to be setup. When the switch is not on,
the RAB assignment request is rejected. 11.
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH:
When this switch is on, the cell individual offset (CIO) of the
best cell is always set to 0 in the INTRA-FREQUENCY
MEASUREMENT CONTROL messages. Otherwise, the CIO
information of the best cell is not carried in the INTRAFREQUENCY MEASUREMENT CONTROL messages. 12.
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH:
When the switch is on, the cell synchronization information
traced by the IOS need to be reported during the RRC
measurement period. 13.
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH: When
the switch is on, the active set update is in the same procedure as
the change of the serving cell. When the switch is not on, the
serving cell is changed after the UE updates the active set and
delivers reconfiguration of physical channels. This switch is
applicable only to R6 or aboveUEs. 14.
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH:
When the switch is on, channel transition is in the same
procedure as the change of the serving cell. When the switch is
not on, the serving cell is changed after the UE performs channel
transition and delivers reconfiguration of physical channels. 15.
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH: By
default, the switch is on. In this case, the Alternative E-bit is not
configured for L2. 16.
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH: When the
switch is set to ON, only uplink RLC or downlink RLC can be

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
HS
DP
A

Description

re-established during the state transition from CELL_FACH to


CELL_FACH (F2F for short). 17.
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH: When the
switch is set to ON, only uplink RLC or downlink RLC can be
re-established during the state transition from CELL_DCH to
CELL_FACH (D2F for short). 18.
CMP_RAB_5_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 5 can be configured with the
Robust Header Compression (ROHC) function. When the switch
is set to OFF, the service with RAB ID 5 cannot be configured
with the ROHC function. 19.
CMP_RAB_6_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 6 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 6 cannot be configured with the ROHC function. 20.
CMP_RAB_7_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 7 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 7 cannot be configured with the ROHC function. 21.
CMP_RAB_8_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 8 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 8 cannot be configured with the ROHC function. 22.
CMP_RAB_9_CFG_ROHC_SWITCH: When the switch is set
to ON, the service with RAB ID 9 can be configured with the
ROHC function. When the switch is set to OFF, the service with
RAB ID 9 cannot be configured with the ROHC function. 23.
CMP_HSUPA_MACD_FLOW_MUL_SWITCH: When the
switch is set to ON, MAC-d flow can be multiplexed without any
restrictions. When the switch is set to OFF, only MAC-d flows
whose scheduling priority is lower than that of the current MACd flow can be multiplexed. 24.
CMP_SMLC_RSLT_MODE_TYPE_SWITCH: If the Client
Type of a positioning request is Emergency Services, PLMN
Operator Services, PLMN Operator - broadcast services, PLMN
Operator - O&M, PLMN Operator - anonymous statistics or
PLMN Operator - Target MS service support, the positioning
result is reported by using the Ellipsoid point with uncertainty
circle type. For other client types, the positioning result is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

reported by using the Ellipsoid Arc type. 25.


CMP_F2P_PROCESS_OPTIMIZATION_SWITCH: Switch for
optimizing the procedure for the CELL_FACH-to-CELL_PCHor-URA_PCH state transition. When this switch is set to on, F2P
state transition is performed through the physical channel
reconfiguration procedure.When this switch is set to off, F2P
state transition is performed through the RB reconfiguration
procedure. 26.
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH: Whether to
carry parameters related to events 1A and 1D in system
information block type 11 (SIB 11) and SIB 12.If the switch of
deferred measurement control reading is turned on, the UE
cannot promptly read parameters related to events 1A and 1D for
intra-frequency neighboring cells from SIB 11 or SIB12. As a
result, the UE cannot perform soft handovers in advance. The
switch is set using DeferMcReadInd in the ADD/MOD
UCELLMEAS command.
GUI Value Range:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,
CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH
Unit: None
Actual Value Range:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,
CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_RAB_6_CFG_ROHC_SWITCH,
CMP_RAB_7_CFG_ROHC_SWITCH,
CMP_RAB_8_CFG_ROHC_SWITCH,
CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH
Default Value:
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH:0,CMP_I
U_QOS_ASYMMETRY_IND_COMPAT_SWITCH:0,CMP_IU
_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH:0,CMP_IUR_H2
D_FOR_LOWR5_NRNCCELL_SWITCH:0,CMP_IUR_SHO_
DIVCTRL_SWITCH:0,CMP_UU_ADJACENT_FREQ_CM_S

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

WITCH:0,CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH:1
,CMP_UU_AMR_SID_MUST_CFG_SWITCH:0,CMP_UU_FD
PCH_COMPAT_SWITCH:0,CMP_UU_IGNORE_UE_RLC_C
AP_SWITCH:1,CMP_UU_INTRA_FREQ_MC_BESTCELL_C
IO_SWITCH:0,CMP_UU_IOS_CELL_SYNC_INFO_REPORT
_SWITCH:0,CMP_UU_SERV_CELL_CHG_WITH_ASU_SWI
TCH:0,CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWI
TCH:1,CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWIT
CH:1,CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH:0,CMP
_D2F_RLC_ONESIDE_REBUILD_SWITCH:0,CMP_RAB_5_
CFG_ROHC_SWITCH:0,CMP_RAB_6_CFG_ROHC_SWITC
H:0,CMP_RAB_7_CFG_ROHC_SWITCH:0,CMP_RAB_8_CF
G_ROHC_SWITCH:0,CMP_RAB_9_CFG_ROHC_SWITCH:0,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH:0,CMP_SMLC
_RSLT_MODE_TYPE_SWITCH:0,CMP_F2P_PROCESS_OPT
IMIZATION_SWITCH:0,CMP_UU_SIB11_SIB12_WITH_1A1
D_SWITCH:0
HHO
TRIG

B
S
C
6
9
0
0

ADD
UNR
NC
MOD
UNR
NC

W
RF
D02
03
01
W
RF
D02
03
02
W
RF
D02
03
04
W
RF
D-

Intr
a
Fre
que
ncy
Har
d
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: Indicating whether to trigger hard handover cross the


Iur interface between the RNC and the neighboring RNC.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

04 ed
02 on
02 Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
RN
C
Nod
e
Red
und
anc
y
HHO
TRIG

B
S
C
6
9
1
0

ADD
UNR
NC
MOD
UNR
NC

W
RF
D02
03
01
W
RF
D-

Intr
a
Fre
que
ncy
Har
d
Han
dov

Meaning: Indicating whether to trigger hard handover cross the


Iur interface between the RNC and the neighboring RNC.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

SHOT B ADD
RIG
S UNR
C NC
6 MOD
9 UNR

02
03
02
W
RF
D02
03
04

er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

W
RF
D02
02

Inte
r
RN
C
Soft

Description

Meaning: Indicating whether to trigger soft handover cross the


Iur interface between the RNC and the neighboring RNC: 1)
CS_SHO_SWITCH. Indicating whether to trigger soft handover
for CS cross the Iur interface. 2) HSPA_SHO_SWITCH.
Whether to allow inter-Iur soft handovers for HSPA PS services.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0 NC
0

SHOT B ADD
RIG
S UNR
C NC
6 MOD
9 UNR
1 NC
0

Description

03
M
RF
D21
08
01
W
RF
D04
02
02

Han
dov
er
Inte
rfac
e
Mes
sag
e
Tra
cing
RN
C
Nod
e
Red
und
anc
y

When this switch is turned on, a UE processing HSUPA or


HSDPA PS services can initiate a serving cell change process to
the neighboring RNC. Alternatively, the UE can initiate a soft
handover process and meanwhile changes the existing channel to
a DCH. When this switch is turned off, the UE cannot perform
any of the previous operations. 3) NON_HSPA_SHO_SWITCH.
Indicating whether to trigger soft handover for PS(R99) cross the
Iur interface.
GUI Value Range: CS_SHO_SWITCH, HSPA_SHO_SWITCH,
NON_HSPA_SHO_SWITCH
Unit: None
Actual Value Range: CS_SHO_SWITCH,
HSPA_SHO_SWITCH, NON_HSPA_SHO_SWITCH
Default Value: None

W
RF
D02
02
03
M
RF
D21
08
01

Inte
r
RN
C
Soft
Han
dov
er
Inte
rfac
e
Mes
sag
e
Tra
cing

Meaning: Indicating whether to trigger soft handover cross the


Iur interface between the RNC and the neighboring RNC: 1)
CS_SHO_SWITCH. Indicating whether to trigger soft handover
for CS cross the Iur interface. 2) HSPA_SHO_SWITCH.
Whether to allow inter-Iur soft handovers for HSPA PS services.
When this switch is turned on, a UE processing HSUPA or
HSDPA PS services can initiate a serving cell change process to
the neighboring RNC. Alternatively, the UE can initiate a soft
handover process and meanwhile changes the existing channel to
a DCH. When this switch is turned off, the UE cannot perform
any of the previous operations. 3) NON_HSPA_SHO_SWITCH.
Indicating whether to trigger soft handover for PS(R99) cross the
Iur interface.
GUI Value Range: CS_SHO_SWITCH, HSPA_SHO_SWITCH,
NON_HSPA_SHO_SWITCH
Unit: None
Actual Value Range: CS_SHO_SWITCH,
HSPA_SHO_SWITCH, NON_HSPA_SHO_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Default Value: None


IntraF
reqMe
asQua
ntity

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Measurement quantity for triggering intra-frequency


handovers. Reference measurement quantity for a UE to report
event 1x. For intra-frequency handovers, CPICH Ec/No or RSCP
is used as the measurement quantity. For events 1A, 1B, 1C, and
1D which adopt relative thresholds, the measurement quantity
does not have great impact on the threshold values. For event 1F
which adopts absolute threshold, the measurement quantity
should be set based on actual cell conditions. If the cell is located
in the center of the coverage area, the main factor that affects
signal quality is intra-frequency interference. In this case, you
are advised to set this parameter to CPICH_EC/NO. If the cell is
located at the edge of the coverage area, the main factor that
affects signal quality is the distance between the cell and the base
station. In this case, you are advised to set this parameter to
CPICH_RSCP.
GUI Value Range: CPICH_EC/NO, CPICH_RSCP
Unit: None
Actual Value Range: CPICH_EC/NO, CPICH_RSCP
Default Value: CPICH_EC/NO

IntraF
reqMe
asQua
ntity

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Measurement quantity for triggering intra-frequency


handovers. Reference measurement quantity for a UE to report
event 1x. For intra-frequency handovers, CPICH Ec/No or RSCP
is used as the measurement quantity. For events 1A, 1B, 1C, and
1D which adopt relative thresholds, the measurement quantity
does not have great impact on the threshold values. For event 1F
which adopts absolute threshold, the measurement quantity
should be set based on actual cell conditions. If the cell is located
in the center of the coverage area, the main factor that affects
signal quality is intra-frequency interference. In this case, you
are advised to set this parameter to CPICH_EC/NO. If the cell is
located at the edge of the coverage area, the main factor that
affects signal quality is the distance between the cell and the base
station. In this case, you are advised to set this parameter to
CPICH_RSCP.
GUI Value Range: CPICH_EC/NO, CPICH_RSCP

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Unit: None
Actual Value Range: CPICH_EC/NO, CPICH_RSCP
Default Value: CPICH_EC/NO
MaxC
ellInA
ctiveS
et

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Maximum number of cells in an active set. This


parameter is used to achieve the balance between the signal
quality in the SHO area and the system performance. If more
cells are in the active set, a user can obtain a greater macro
diversity gain; the intra-frequency interference is smaller. In this
case, however, the user occupies resources of several cells. This
increases the amount of data to be processed and lowers the
system performance.
GUI Value Range: 1~6
Unit: None
Actual Value Range: 1~6
Default Value: 3

MaxC
ellInA
ctiveS
et

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Maximum number of cells in an active set. This


parameter is used to achieve the balance between the signal
quality in the SHO area and the system performance. If more
cells are in the active set, a user can obtain a greater macro
diversity gain; the intra-frequency interference is smaller. In this
case, however, the user occupies resources of several cells. This
increases the amount of data to be processed and lowers the
system performance.
GUI Value Range: 1~6
Unit: None
Actual Value Range: 1~6
Default Value: 3

CIO

B ADD

W Intr Meaning: Cell individual offset (CIO) of the current cell. This

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
S
C
6
9
0
0

UCE
LLSE
TUP
MOD
UCE
LLSE
TUP

RF
D02
02
01
W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D02
03
09
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D-

a
Nod
eB
Soft
er
Han
dov
er
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r

Description

parameter works together with "CIOOffset" for intra-frequency


and inter-frequency handover decision. The larger the sum of the
values of this parameter and "CIOOffset", the higher the
probability of handover to the neighboring cell. The smaller the
sum of the values of this parameter and "CIOOffset", the lower
the probability of handover to the neighboring cell. For details
about this parameter, see 3GPP TS 25.331.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
03
04
W
RF
D02
03
05

Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
CIO

B
S
C
6
9
1
0

ADD
UCE
LLSE
TUP
MOD
UCE
LLSE
TUP

W
RF
D02
02
01
W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D02

Intr
a
Nod
eB
Soft
er
Han
dov
er
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft

Meaning: Cell individual offset (CIO) of the current cell. This


parameter works together with "CIOOffset" for intra-frequency
and inter-frequency handover decision. The larger the sum of the
values of this parameter and "CIOOffset", the higher the
probability of handover to the neighboring cell. The smaller the
sum of the values of this parameter and "CIOOffset", the lower
the probability of handover to the neighboring cell. For details
about this parameter, see 3GPP TS 25.331.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
03
09
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
04
W
RF
D02
03
05

Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
CIOO B ADD
ffset
S UINT
C RAF
6 REQ

W
RF
D02

Intr
a
Nod
eB

Meaning: CIO of a neighboring cell. This parameter works with


"CIO". The sum of "CIOOffset", "CIO", and the actual measured
value are used for UE event evaluation or decisions on
handovers triggered by the RNC. In a handover algorithm, this

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
9 NCE 02 Soft
0 LL
01 er
0 MOD
Han
dov
UINT
er
RAF
REQ
NCE
LL

Description

parameter is used for moving the border of a cell. In the case of


an event-based intra-frequency measurement or inter-RAT
measurement, the UE determines whether to trigger an event
according to the sum of "CIOOffset", "CIO", and the actual
measured value. The UE does not consider the value of this
parameter when evaluating an inter-frequency measurement
event. In the case of a periodical inter-frequency measurement or
inter-RAT measurement, the RNC determines whether to initiate
a handover based on the sum of "CIOOffset", "CIO", and the
actual measured value.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
Default Value: 0

CIOO B ADD
ffset
S UINT
C RAF
6 REQ
9 NCE
1 LL
0 MOD
UINT
RAF
REQ
NCE
LL

W
RF
D02
02
01

Intr
a
Nod
eB
Soft
er
Han
dov
er

Meaning: CIO of a neighboring cell. This parameter works with


"CIO". The sum of "CIOOffset", "CIO", and the actual measured
value are used for UE event evaluation or decisions on
handovers triggered by the RNC. In a handover algorithm, this
parameter is used for moving the border of a cell. In the case of
an event-based intra-frequency measurement or inter-RAT
measurement, the UE determines whether to trigger an event
according to the sum of "CIOOffset", "CIO", and the actual
measured value. The UE does not consider the value of this
parameter when evaluating an inter-frequency measurement
event. In the case of a periodical inter-frequency measurement or
inter-RAT measurement, the RNC determines whether to initiate
a handover based on the sum of "CIOOffset", "CIO", and the
actual measured value.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
Default Value: 0

Weigh B ADD
t
S UCE
C LLIN
6 TRAF

W
RF
D02

Inte
r
RN
C

Meaning: Used for calculating the relative threshold of the soft


handover based on the measurement report of each cell in the
active set. If this parameter is set to a greater value, the relative
threshold of the soft handover is greater with the other conditions

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

02
03
W
RF
D02
02
02

Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

unchanged. For detailed information of this parameter, refer to


3GPP TS 25.133. When this parameter is set to 0, the general
quality of the active set is the quality of the best cell. In this case,
the relative threshold of soft handover depends on the related
measurement values of the best cell in the active set. When this
parameter is set to 1, the relative threshold of the soft handover
depends on the equivalent signal strength obtained when
maximum ratio combining is performed in the downlink of all
cells in the active set.
GUI Value Range: 0~20
Unit: None
Actual Value Range: 0~2, step: 0.1
Default Value: 0

Weigh B ADD
t
S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Used for calculating the relative threshold of the soft


handover based on the measurement report of each cell in the
active set. If this parameter is set to a greater value, the relative
threshold of the soft handover is greater with the other conditions
unchanged. For detailed information of this parameter, refer to
3GPP TS 25.133. When this parameter is set to 0, the general
quality of the active set is the quality of the best cell. In this case,
the relative threshold of soft handover depends on the related
measurement values of the best cell in the active set. When this
parameter is set to 1, the relative threshold of the soft handover
depends on the equivalent signal strength obtained when
maximum ratio combining is performed in the downlink of all
cells in the active set.
GUI Value Range: 0~20
Unit: None
Actual Value Range: 0~2, step: 0.1
Default Value: 0

CellsF B ADD W
orbidd S UINT RF
en1A C RAF D6 REQ 02
9 NCE 02
0 LL
03

Inte
r
RN
C
Soft
Han

Meaning: Determines whether event 1A threshold is affected


when the cell is added to the active set. If this parameter is set to
"NOT_AFFECT", the relative threshold of event 1A is not
affected when the cell is added to the active set. That is, the cell
signals are N/A when the UE evaluates whether event 1A should
be triggered. If this parameter is set to "AFFECT", the relative

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0 MOD
UINT
RAF
REQ
NCE
LL

Description

W
RF
D02
02
02

dov
er
Intr
a
RN
C
Soft
Han
dov
er

threshold of event 1A is affected when the cell is added to the


active set. That is, the cell signals are involved when the UE
evaluates whether event 1A should be triggered.
GUI Value Range: AFFECT, NOT_AFFECT
Unit: None
Actual Value Range: AFFECT, NOT_AFFECT
Default Value: AFFECT

CellsF B ADD W
orbidd S UINT RF
en1A C RAF D6 REQ 02
9 NCE 02
1 LL
03
0 MOD W
UINT RF
RAF DREQ 02
NCE 02
LL
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Determines whether event 1A threshold is affected


when the cell is added to the active set. If this parameter is set to
"NOT_AFFECT", the relative threshold of event 1A is not
affected when the cell is added to the active set. That is, the cell
signals are N/A when the UE evaluates whether event 1A should
be triggered. If this parameter is set to "AFFECT", the relative
threshold of event 1A is affected when the cell is added to the
active set. That is, the cell signals are involved when the UE
evaluates whether event 1A should be triggered.
GUI Value Range: AFFECT, NOT_AFFECT
Unit: None
Actual Value Range: AFFECT, NOT_AFFECT
Default Value: AFFECT

IntraR
elThd
For1A
CSNV
P

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN

Meaning: Relative threshold for event 1A decision when non-VP


service is performed in CS domain. If this parameter is set to a
greater value, the probability of triggering event 1A increases. If
this parameter is set to a smaller value, the probability of
triggering event 1A reduces. For details on the definition of
event 1A, see 3GPP TS 25.331.The relative threshold can
directly affect the SHO ratio. Therefore, the threshold should be
wisely chosen to achieve smooth SHOs. The value of this
parameter determines the SHO area and SHO ratio. In the
CDMA system, the ratio of the UE involved in soft handover
should reach 30% to 40% to ensure smooth handover. Based on

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

IntraR
elThd
For1A
CSNV
P

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

Description

02 C
Soft
Han
dov
er

simulation results, when the relative threshold is set to 5 dB, the


ratio of the UE involved in soft handover (the number of cells in
the active set is at least 2) is about 35%. you are advised to set
the relative threshold to a great value (5 dB to 7 dB) during site
deployment, and to reduce the threshold when the users increase.
the threshold must be higher than 3 dB to avoid the ping-pong
handover. You can set different relative thresholds for event 1A
and event 1B to reduce the ping-pong effect and change the soft
handover ratio. In general applications, the relative thresholds for
events 1A and 1B should be consistent, and you can curb the
ping-pong effect through the triggering delay, L3 filtering
coefficient, and hysteresis. In some specific applications, if the
ping-pong effect cannot be curbed by adjusting the hysteresis
values for event 1A and event 1B, you can curb it by setting a
higher relative threshold for event 1B and a lower threshold for
event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6

W
RF
D02
02
03
W
RF
D02
02
02

Meaning: Relative threshold for event 1A decision when non-VP


service is performed in CS domain. If this parameter is set to a
greater value, the probability of triggering event 1A increases. If
this parameter is set to a smaller value, the probability of
triggering event 1A reduces. For details on the definition of
event 1A, see 3GPP TS 25.331.The relative threshold can
directly affect the SHO ratio. Therefore, the threshold should be
wisely chosen to achieve smooth SHOs. The value of this
parameter determines the SHO area and SHO ratio. In the
CDMA system, the ratio of the UE involved in soft handover
should reach 30% to 40% to ensure smooth handover. Based on
simulation results, when the relative threshold is set to 5 dB, the
ratio of the UE involved in soft handover (the number of cells in
the active set is at least 2) is about 35%. you are advised to set
the relative threshold to a great value (5 dB to 7 dB) during site
deployment, and to reduce the threshold when the users increase.
the threshold must be higher than 3 dB to avoid the ping-pong
handover. You can set different relative thresholds for event 1A

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

and event 1B to reduce the ping-pong effect and change the soft
handover ratio. In general applications, the relative thresholds for
events 1A and 1B should be consistent, and you can curb the
ping-pong effect through the triggering delay, L3 filtering
coefficient, and hysteresis. In some specific applications, if the
ping-pong effect cannot be curbed by adjusting the hysteresis
values for event 1A and event 1B, you can curb it by setting a
higher relative threshold for event 1B and a lower threshold for
event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6
IntraR
elThd
For1A
CSVP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1A decision when VP


service is performed. If this parameter is set to a greater value,
the probability of triggering event 1A increases. If this parameter
is set to a smaller value, the probability of triggering event 1A
reduces. For details on the definition of event 1A, see 3GPP TS
25.331.The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. you are advised to set the relative threshold to a great
value (5 dB to 7 dB) during site deployment, and to reduce the
threshold when the users increase. the threshold must be higher
than 3 dB to avoid the ping-pong handover. You can set different
relative thresholds for event 1A and event 1B to reduce the pingpong effect and change the soft handover ratio. In general
applications, the relative thresholds for events 1A and 1B should
be consistent, and you can curb the ping-pong effect through the
triggering delay, L3 filtering coefficient, and hysteresis. In some
specific applications, if the ping-pong effect cannot be curbed by
adjusting the hysteresis values for event 1A and event 1B, you
can curb it by setting a higher relative threshold for event 1B and

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

a lower threshold for event 1A.


GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6
IntraR
elThd
For1A
CSVP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

IntraR B ADD

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1A decision when VP


service is performed. If this parameter is set to a greater value,
the probability of triggering event 1A increases. If this parameter
is set to a smaller value, the probability of triggering event 1A
reduces. For details on the definition of event 1A, see 3GPP TS
25.331.The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. you are advised to set the relative threshold to a great
value (5 dB to 7 dB) during site deployment, and to reduce the
threshold when the users increase. the threshold must be higher
than 3 dB to avoid the ping-pong handover. You can set different
relative thresholds for event 1A and event 1B to reduce the pingpong effect and change the soft handover ratio. In general
applications, the relative thresholds for events 1A and 1B should
be consistent, and you can curb the ping-pong effect through the
triggering delay, L3 filtering coefficient, and hysteresis. In some
specific applications, if the ping-pong effect cannot be curbed by
adjusting the hysteresis values for event 1A and event 1B, you
can curb it by setting a higher relative threshold for event 1B and
a lower threshold for event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6

W Inte Meaning: Relative threshold for event 1A decision when PS

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

elThd S UCE RF
For1A C LLIN DPS
6 TRAF 02
9 REQ 02
0 HO
03
0 MOD W
UCE RF
LLIN DTRAF 02
REQ 02
HO
02

r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

service is performed. If this parameter is set to a greater value,


the probability of triggering event 1A increases. If this parameter
is set to a smaller value, the probability of triggering event 1A
reduces. For details on the definition of event 1A, see 3GPP TS
25.331. The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. You are advised to set the relative threshold to a
great value (5 dB to 7 dB) during site deployment, and to reduce
the threshold when the users increase. the threshold must be
higher than 3 dB to avoid the ping-pong handover. You can set
different relative thresholds for event 1A and event 1B to reduce
the ping-pong effect and change the soft handover ratio. In
general applications, the relative thresholds for events 1A and 1B
should be consistent, and you can curb the ping-pong effect
through the triggering delay, L3 filtering coefficient, and
hysteresis. In some specific applications, if the ping-pong effect
cannot be curbed by adjusting the hysteresis values for event 1A
and event 1B, you can curb it by setting a higher relative
threshold for event 1B and a lower threshold for event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6

IntraR
elThd
For1A
PS

Inte
r
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1A decision when PS


service is performed. If this parameter is set to a greater value,
the probability of triggering event 1A increases. If this parameter
is set to a smaller value, the probability of triggering event 1A
reduces. For details on the definition of event 1A, see 3GPP TS
25.331. The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN

W
RF
D02
02
03
W
RF
D-

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
TRAF 02 Intr
REQ 02 a
HO
02 RN
C
Soft
Han
dov
er

HystF B ADD
or1A S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Description

involved in soft handover should reach 30% to 40% to ensure


smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. You are advised to set the relative threshold to a
great value (5 dB to 7 dB) during site deployment, and to reduce
the threshold when the users increase. the threshold must be
higher than 3 dB to avoid the ping-pong handover. You can set
different relative thresholds for event 1A and event 1B to reduce
the ping-pong effect and change the soft handover ratio. In
general applications, the relative thresholds for events 1A and 1B
should be consistent, and you can curb the ping-pong effect
through the triggering delay, L3 filtering coefficient, and
hysteresis. In some specific applications, if the ping-pong effect
cannot be curbed by adjusting the hysteresis values for event 1A
and event 1B, you can curb it by setting a higher relative
threshold for event 1B and a lower threshold for event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6
Meaning: Hysteresis for triggering event 1A. For details, see
3GPP TS 25.331. This parameter can be used to reduce pingpong handovers and unnecessary handovers. When adjusting the
setting of this parameter, you need to consider the filter
coefficient and the interval between detection of event 1A and
sending of the measurement report.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

HystF B ADD
or1A S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Hysteresis for triggering event 1A. For details, see


3GPP TS 25.331. This parameter can be used to reduce pingpong handovers and unnecessary handovers. When adjusting the
setting of this parameter, you need to consider the filter
coefficient and the interval between detection of event 1A and
sending of the measurement report.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

IntraR
elThd
For1A
CSNV
P

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1A decision when non-VP


service is performed in CS domain. If this parameter is set to a
greater value, the probability of triggering event 1A increases. If
this parameter is set to a smaller value, the probability of
triggering event 1A reduces. For details on the definition of
event 1A, see 3GPP TS 25.331.The relative threshold can
directly affect the SHO ratio. Therefore, the threshold should be
wisely chosen to achieve smooth SHOs. The value of this
parameter determines the SHO area and SHO ratio. In the
CDMA system, the ratio of the UE involved in soft handover
should reach 30% to 40% to ensure smooth handover. Based on
simulation results, when the relative threshold is set to 5 dB, the
ratio of the UE involved in soft handover (the number of cells in
the active set is at least 2) is about 35%. you are advised to set
the relative threshold to a great value (5 dB to 7 dB) during site
deployment, and to reduce the threshold when the users increase.
the threshold must be higher than 3 dB to avoid the ping-pong
handover. You can set different relative thresholds for event 1A
and event 1B to reduce the ping-pong effect and change the soft
handover ratio. In general applications, the relative thresholds for
events 1A and 1B should be consistent, and you can curb the
ping-pong effect through the triggering delay, L3 filtering

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

coefficient, and hysteresis. In some specific applications, if the


ping-pong effect cannot be curbed by adjusting the hysteresis
values for event 1A and event 1B, you can curb it by setting a
higher relative threshold for event 1B and a lower threshold for
event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6
IntraR
elThd
For1A
CSNV
P

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1A decision when non-VP


service is performed in CS domain. If this parameter is set to a
greater value, the probability of triggering event 1A increases. If
this parameter is set to a smaller value, the probability of
triggering event 1A reduces. For details on the definition of
event 1A, see 3GPP TS 25.331.The relative threshold can
directly affect the SHO ratio. Therefore, the threshold should be
wisely chosen to achieve smooth SHOs. The value of this
parameter determines the SHO area and SHO ratio. In the
CDMA system, the ratio of the UE involved in soft handover
should reach 30% to 40% to ensure smooth handover. Based on
simulation results, when the relative threshold is set to 5 dB, the
ratio of the UE involved in soft handover (the number of cells in
the active set is at least 2) is about 35%. you are advised to set
the relative threshold to a great value (5 dB to 7 dB) during site
deployment, and to reduce the threshold when the users increase.
the threshold must be higher than 3 dB to avoid the ping-pong
handover. You can set different relative thresholds for event 1A
and event 1B to reduce the ping-pong effect and change the soft
handover ratio. In general applications, the relative thresholds for
events 1A and 1B should be consistent, and you can curb the
ping-pong effect through the triggering delay, L3 filtering
coefficient, and hysteresis. In some specific applications, if the
ping-pong effect cannot be curbed by adjusting the hysteresis
values for event 1A and event 1B, you can curb it by setting a
higher relative threshold for event 1B and a lower threshold for
event 1A.
GUI Value Range: 0~29

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6
TrigTi B ADD
me1A S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D15
02
05

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Lay
ered
Pag
ing
in
Idle
Mo
de

Meaning: This parameter specifies the interval time between


detection of event 1A and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate triggering delay effectively reduces the average
number of handovers and the number of wrong handovers,
preventing unnecessary handovers. If the handover cannot be
triggered in time, the time-to-trigger parameter for event 1A
needs to be changed to 200 ms or 100 ms, and the delay for
event 1B needs to be changed to 1280 ms or 2560 ms.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D320

TrigTi B ADD
me1A S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF

W
RF
D02
02
03
W
RF
D02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a

Meaning: This parameter specifies the interval time between


detection of event 1A and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

REQ
HO

02
02
W
RF
D15
02
05

RN
C
Soft
Han
dov
er
Lay
ered
Pag
ing
in
Idle
Mo
de

appropriate triggering delay effectively reduces the average


number of handovers and the number of wrong handovers,
preventing unnecessary handovers. If the handover cannot be
triggered in time, the time-to-trigger parameter for event 1A
needs to be changed to 200 ms or 100 ms, and the delay for
event 1B needs to be changed to 1280 ms or 2560 ms.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D320

CellsF B ADD W
orbidd S UINT RF
en1B C RAF D6 REQ 02
9 NCE 02
0 LL
03
0 MOD W
UINT RF
RAF DREQ 02
NCE 02
LL
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Flag of whether adding a cell into the active set will
affect the relative threshold of the event 1B. This parameter is a
flag of whether adding the cell into the active set will affect the
relative threshold of the event 1B NOT_AFFECT: Adding the
cell into the active set does not affect the relative threshold of the
event 1B. The cell signal will affect the UE evaluate whether
event 1B should occur. AFFECT: Adding the cell into the active
set affects the relative threshold of the event 1B. The cell signal
will not affect the UE evaluate whether event 1B should occur.
GUI Value Range: AFFECT, NOT_AFFECT
Unit: None
Actual Value Range: AFFECT, NOT_AFFECT
Default Value: AFFECT

CellsF B ADD W
orbidd S UINT RF
en1B C RAF D6 REQ 02
9 NCE 02
1 LL
03
0 MOD W

Inte
r
RN
C
Soft
Han
dov

Meaning: Flag of whether adding a cell into the active set will
affect the relative threshold of the event 1B. This parameter is a
flag of whether adding the cell into the active set will affect the
relative threshold of the event 1B NOT_AFFECT: Adding the
cell into the active set does not affect the relative threshold of the
event 1B. The cell signal will affect the UE evaluate whether
event 1B should occur. AFFECT: Adding the cell into the active

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

IntraR
elThd
For1B
CSNV
P

B
S
C
6
9
0
0

Description

UINT
RAF
REQ
NCE
LL

RF
D02
02
02

er
Intr
a
RN
C
Soft
Han
dov
er

set affects the relative threshold of the event 1B. The cell signal
will not affect the UE evaluate whether event 1B should occur.
GUI Value Range: AFFECT, NOT_AFFECT
Unit: None
Actual Value Range: AFFECT, NOT_AFFECT
Default Value: AFFECT

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1B decision when non-VP


service is performed in CS domain. If this parameter is set to a
smaller value, the probability of triggering event 1B increases. If
this parameter is set to a greater value, the probability of
triggering event 1B reduces. For details on the definition of
event 1B, see 3GPP TS 25.331. The relative threshold can
directly affect the SHO ratio. Therefore, the threshold should be
wisely chosen to achieve smooth SHOs. The value of this
parameter determines the SHO area and SHO ratio. In the
CDMA system, the ratio of the UE involved in soft handover
should reach 30% to 40% to ensure smooth handover. Based on
simulation results, when the relative threshold is set to 5 dB, the
ratio of the UE involved in soft handover (the number of cells in
the active set is at least 2) is about 35%. You are advised to set
the relative threshold to a great value (5 dB to 7 dB) during site
deployment, and to reduce the threshold when the users increase.
the threshold must be higher than 3 dB to avoid the ping-pong
handover. You can set different relative thresholds for event 1A
and event 1B to reduce the ping-pong effect and change the soft
handover ratio. In general applications, the relative thresholds for
events 1A and 1B should be consistent, and you can curb the
ping-pong effect through the triggering delay, L3 filtering
coefficient, and hysteresis. In some specific applications, if the
ping-pong effect cannot be curbed by adjusting the hysteresis
values for event 1A and event 1B, you can curb it by setting a
higher relative threshold for event 1B and a lower threshold for
event 1A.
GUI Value Range: 0~29
Unit: 0.5dB

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range: 0~14.5


Default Value: 12
IntraR
elThd
For1B
CSNV
P

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1B decision when non-VP


service is performed in CS domain. If this parameter is set to a
smaller value, the probability of triggering event 1B increases. If
this parameter is set to a greater value, the probability of
triggering event 1B reduces. For details on the definition of
event 1B, see 3GPP TS 25.331. The relative threshold can
directly affect the SHO ratio. Therefore, the threshold should be
wisely chosen to achieve smooth SHOs. The value of this
parameter determines the SHO area and SHO ratio. In the
CDMA system, the ratio of the UE involved in soft handover
should reach 30% to 40% to ensure smooth handover. Based on
simulation results, when the relative threshold is set to 5 dB, the
ratio of the UE involved in soft handover (the number of cells in
the active set is at least 2) is about 35%. You are advised to set
the relative threshold to a great value (5 dB to 7 dB) during site
deployment, and to reduce the threshold when the users increase.
the threshold must be higher than 3 dB to avoid the ping-pong
handover. You can set different relative thresholds for event 1A
and event 1B to reduce the ping-pong effect and change the soft
handover ratio. In general applications, the relative thresholds for
events 1A and 1B should be consistent, and you can curb the
ping-pong effect through the triggering delay, L3 filtering
coefficient, and hysteresis. In some specific applications, if the
ping-pong effect cannot be curbed by adjusting the hysteresis
values for event 1A and event 1B, you can curb it by setting a
higher relative threshold for event 1B and a lower threshold for
event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 12

IntraR
elThd
For1B
CSVP

B
S
C
6

ADD
UCE
LLIN
TRAF

W
RF
D02

Inte
r
RN
C

Meaning: Relative threshold for event 1B decision when VP


service is performed. If this parameter is set to a smaller value,
the probability of triggering event 1B increases. If this parameter
is set to a greater value, the probability of triggering event 1B

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

IntraR
elThd
For1B
CSVP

Description

9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

02
03
W
RF
D02
02
02

Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

reduces. For details on the definition of event 1B, see 3GPP TS


25.331. The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. You are advised to set the relative threshold to a
great value (5 dB to 7 dB) during site deployment, and to reduce
the threshold when the users increase. the threshold must be
higher than 3 dB to avoid the ping-pong handover. You can set
different relative thresholds for event 1A and event 1B to reduce
the ping-pong effect and change the soft handover ratio. In
general applications, the relative thresholds for events 1A and 1B
should be consistent, and you can curb the ping-pong effect
through the triggering delay, L3 filtering coefficient, and
hysteresis. In some specific applications, if the ping-pong effect
cannot be curbed by adjusting the hysteresis values for event 1A
and event 1B, you can curb it by setting a higher relative
threshold for event 1B and a lower threshold for event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 12

B
S
C
6
9
1
0

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C

Meaning: Relative threshold for event 1B decision when VP


service is performed. If this parameter is set to a smaller value,
the probability of triggering event 1B increases. If this parameter
is set to a greater value, the probability of triggering event 1B
reduces. For details on the definition of event 1B, see 3GPP TS
25.331. The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

IntraR
elThd
For1B
PS

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Description

Soft
Han
dov
er

handover (the number of cells in the active set is at least 2) is


about 35%. You are advised to set the relative threshold to a
great value (5 dB to 7 dB) during site deployment, and to reduce
the threshold when the users increase. the threshold must be
higher than 3 dB to avoid the ping-pong handover. You can set
different relative thresholds for event 1A and event 1B to reduce
the ping-pong effect and change the soft handover ratio. In
general applications, the relative thresholds for events 1A and 1B
should be consistent, and you can curb the ping-pong effect
through the triggering delay, L3 filtering coefficient, and
hysteresis. In some specific applications, if the ping-pong effect
cannot be curbed by adjusting the hysteresis values for event 1A
and event 1B, you can curb it by setting a higher relative
threshold for event 1B and a lower threshold for event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 12

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1B decision when PS


service is performed. If this parameter is set to a smaller value,
the probability of triggering event 1B increases. If this parameter
is set to a greater value, the probability of triggering event 1B
reduces. For details on the definition of event 1B, see 3GPP TS
25.331. The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. You are advised to set the relative threshold to a
great value (5 dB to 7 dB) during site deployment, and to reduce
the threshold when the users increase. the threshold must be
higher than 3 dB to avoid the ping-pong handover. You can set
different relative thresholds for event 1A and event 1B to reduce
the ping-pong effect and change the soft handover ratio. In
general applications, the relative thresholds for events 1A and 1B

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

should be consistent, and you can curb the ping-pong effect


through the triggering delay, L3 filtering coefficient, and
hysteresis. In some specific applications, if the ping-pong effect
cannot be curbed by adjusting the hysteresis values for event 1A
and event 1B, you can curb it by setting a higher relative
threshold for event 1B and a lower threshold for event 1A.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 12
IntraR
elThd
For1B
PS

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for event 1B decision when PS


service is performed. If this parameter is set to a smaller value,
the probability of triggering event 1B increases. If this parameter
is set to a greater value, the probability of triggering event 1B
reduces. For details on the definition of event 1B, see 3GPP TS
25.331. The relative threshold can directly affect the SHO ratio.
Therefore, the threshold should be wisely chosen to achieve
smooth SHOs. The value of this parameter determines the SHO
area and SHO ratio. In the CDMA system, the ratio of the UE
involved in soft handover should reach 30% to 40% to ensure
smooth handover. Based on simulation results, when the relative
threshold is set to 5 dB, the ratio of the UE involved in soft
handover (the number of cells in the active set is at least 2) is
about 35%. You are advised to set the relative threshold to a
great value (5 dB to 7 dB) during site deployment, and to reduce
the threshold when the users increase. the threshold must be
higher than 3 dB to avoid the ping-pong handover. You can set
different relative thresholds for event 1A and event 1B to reduce
the ping-pong effect and change the soft handover ratio. In
general applications, the relative thresholds for events 1A and 1B
should be consistent, and you can curb the ping-pong effect
through the triggering delay, L3 filtering coefficient, and
hysteresis. In some specific applications, if the ping-pong effect
cannot be curbed by adjusting the hysteresis values for event 1A
and event 1B, you can curb it by setting a higher relative
threshold for event 1B and a lower threshold for event 1A.
GUI Value Range: 0~29

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 12
HystF B ADD
or1B S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the hysteretic value for event


1B. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

HystF B ADD
or1B S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the hysteretic value for event


1B. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

TrigTi B ADD

W Inte Meaning: This parameter specifies the interval time between

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
me1B S
C
6
9
0
0

Description

UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

RF
D02
02
03
W
RF
D02
02
02

r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

detection of event 1B and sending of the measurement report.


The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers. If the handover cannot be triggered in
time, the time-to-trigger parameter for event 1A needs to be
changed to 200 ms or 100 ms, and the delay for event 1B needs
to be changed to 1280 ms or 2560 ms.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

TrigTi B ADD
me1B S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the interval time between


detection of event 1B and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers. If the handover cannot be triggered in
time, the time-to-trigger parameter for event 1A needs to be
changed to 200 ms or 100 ms, and the delay for event 1B needs
to be changed to 1280 ms or 2560 ms.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

D160, D200, D240, D320, D640, D1280, D2560, D5000


Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640
HystF B ADD
or1C S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the hysteretic value for event


1C. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

HystF B ADD
or1C S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov

Meaning: This parameter specifies the hysteretic value for event


1C. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
TrigTi B ADD
me1C S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the interval time between


detection of event 1C and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

TrigTi B ADD
me1C S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the interval time between


detection of event 1C and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640
HystF B ADD
or1D S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the hysteretic value for event


1D. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

HystF B ADD
or1D S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the hysteretic value for event


1D. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

TrigTi B ADD

W Inte Meaning: This parameter specifies the interval time between

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
me1D S
C
6
9
0
0

Description

UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

RF
D02
02
03
W
RF
D02
02
02

r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

detection of event 1D and sending of the measurement report.


The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

TrigTi B ADD
me1D S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the interval time between


detection of event 1D and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

SHOQ B ADD
ualmi S UCE
n
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: If events 1A, 1C, and 1D are reported to the RNC, the
target cell can be added to the active set only when CPICH
Ec/No is greater than this parameter. This parameter is used to
set a baseline for the quality of the radio links to be added. The
current events of soft handovers are defined on the basis of
relative thresholds and have no requirement for the absolute
quality. If the signal quality of added cells is too poor, the
general quality of the active set cannot be improved. In this case,
however, more downlink resources are occupied and more TPC
errors are caused, and the soft handover performance is
worsened. Therefore, this parameter is required.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -20

SHOQ B ADD
ualmi S UCE
n
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: If events 1A, 1C, and 1D are reported to the RNC, the
target cell can be added to the active set only when CPICH
Ec/No is greater than this parameter. This parameter is used to
set a baseline for the quality of the radio links to be added. The
current events of soft handovers are defined on the basis of
relative thresholds and have no requirement for the absolute
quality. If the signal quality of added cells is too poor, the
general quality of the active set cannot be improved. In this case,
however, more downlink resources are occupied and more TPC
errors are caused, and the soft handover performance is
worsened. Therefore, this parameter is required.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -20

RelTh
dForD
wnGr
d

W
RF
D02
02

Inte
r
RN
C
Soft

Meaning: Relative threshold for immediate rate reduction after


soft handover failure. The rate reduction of the active set and soft
handover retry procedure can be triggered without intrafrequency measurement reports if the quality of the cell in the
active set fulfills the following criterion: Mnew > Mbest_cell -

B
S
C
6
9

SET
UINT
RAF
REQ
HO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0
0

Description

03
W
RF
D02
02
02

Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

RelThdForDwnGrd Mnew indicates the CPICH Ec/No


measurement value of Cell1 where the UE fails to be admitted.
Mbest_cell indicates the CPICH Ec/No measurement value in
the latest measurement report of the best cell identified by the
RNC according to 1D. RelThdForDwnGrd indicates the relative
threshold for immediate rate reduction and can be configured on
the OMU server. If this parameter is set to 29, rate reduction
after soft handover failure is disabled.
GUI Value Range: -29~29
Unit: 0.5dB
Actual Value Range: -14.5~14.5
Default Value: 2

RelTh
dForD
wnGr
d

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Relative threshold for immediate rate reduction after


soft handover failure. The rate reduction of the active set and soft
handover retry procedure can be triggered without intrafrequency measurement reports if the quality of the cell in the
active set fulfills the following criterion: Mnew > Mbest_cell RelThdForDwnGrd Mnew indicates the CPICH Ec/No
measurement value of Cell1 where the UE fails to be admitted.
Mbest_cell indicates the CPICH Ec/No measurement value in
the latest measurement report of the best cell identified by the
RNC according to 1D. RelThdForDwnGrd indicates the relative
threshold for immediate rate reduction and can be configured on
the OMU server. If this parameter is set to 29, rate reduction
after soft handover failure is disabled.
GUI Value Range: -29~29
Unit: 0.5dB
Actual Value Range: -14.5~14.5
Default Value: 2

ShoFa
ilNum
ForD
wnGr
d

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
03
W

Inte
r
RN
C
Soft
Han
dov

Meaning: Maximum allowed number of soft handover failures.


This parameter specifies the maximum number of event
reporting from the cell that fails to be added to the active set for
soft handovers. If the parameter value is reached, rate reduction
of the active set will be triggered and the cell will attempt to join
the active set again. This parameter needs to be considered in
combination with the settings of rate reduction evaluation

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RF
D02
02
02

er
Intr
a
RN
C
Soft
Han
dov
er

period("ShoFailPeriod") and the reporting intervals of events 1A


and 1C("ReportIntervalfor1A" and "ReportIntervalfor1C").
Otherwise, the number of reports cannot reach the required value
to trigger rate reduction during the rate reduction evaluation
period for soft handovers. If this parameter is set to 0, rate
reduction after soft handover failure is disabled.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~63
Default Value: 3

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Maximum allowed number of soft handover failures.


This parameter specifies the maximum number of event
reporting from the cell that fails to be added to the active set for
soft handovers. If the parameter value is reached, rate reduction
of the active set will be triggered and the cell will attempt to join
the active set again. This parameter needs to be considered in
combination with the settings of rate reduction evaluation
period("ShoFailPeriod") and the reporting intervals of events 1A
and 1C("ReportIntervalfor1A" and "ReportIntervalfor1C").
Otherwise, the number of reports cannot reach the required value
to trigger rate reduction during the rate reduction evaluation
period for soft handovers. If this parameter is set to 0, rate
reduction after soft handover failure is disabled.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~63
Default Value: 3

ShoFa B SET W
ilPerio S UINT RF
d
C RAF D6 REQ 02
9 HO
02
0
03
0
W
RF
D-

Inte
r
RN
C
Soft
Han
dov
er
Intr

Meaning: Maximum evaluation period for rate reduction after


soft handover failure. When rate reduction evaluation is
performed on a cell that fails to join the active set, the evaluation
timer is started. If the cell cannot fulfill the criteria for rate
reduction before the timer expires, the cell will not be evaluated
and rate reduction re-attempt will not be initiated.
GUI Value Range: 0~120
Unit: s
Actual Value Range: 0~120

ShoFa
ilNum
ForD
wnGr
d

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

02 a
Default Value: 60
02 RN
02 C
Soft
Han
dov
er
ShoFa B SET W
ilPerio S UINT RF
d
C RAF D6 REQ 02
9 HO
02
1
03
0
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Maximum evaluation period for rate reduction after


soft handover failure. When rate reduction evaluation is
performed on a cell that fails to join the active set, the evaluation
timer is started. If the cell cannot fulfill the criteria for rate
reduction before the timer expires, the cell will not be evaluated
and rate reduction re-attempt will not be initiated.
GUI Value Range: 0~120
Unit: s
Actual Value Range: 0~120
Default Value: 60

DcccS
hoPen
altyTi
me

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Length of penalty timer for soft handover failure after


rate reduction in the active set. When the rate reduction in the
active set is performed and the re-attempt for adding the cell to
the active set is initiated, the RNC starts the penalty timer for
soft handover failure if the target cell fails to join the active
again. Before the timer expires, rate increase in the active set is
prohibited but rate reduction is not prohibited. The penalty
policy is applied in the following scenario: A cell, which has
high signal strength and heavy traffic load, cannot be added to
the active set. This cell enters the soft handover rate reduction
evaluation process repeatedly, which results in rate reduction in
the active set. If the cell fails to be added to the active set, the
rate in the active set increases during the evaluation process
because of the DCCC algorithm. To avoid such rate fluctuation,

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

the RNC uses the mechanism of rate increase penalty after soft
handover rate reduction fails again.
GUI Value Range: 0~255
Unit: s
Actual Value Range: 0~255
Default Value: 30
DcccS
hoPen
altyTi
me

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

W
RF
D02
02
02

Intr
a
RN
C
Soft
Han
dov
er

Meaning: Length of penalty timer for soft handover failure after


rate reduction in the active set. When the rate reduction in the
active set is performed and the re-attempt for adding the cell to
the active set is initiated, the RNC starts the penalty timer for
soft handover failure if the target cell fails to join the active
again. Before the timer expires, rate increase in the active set is
prohibited but rate reduction is not prohibited. The penalty
policy is applied in the following scenario: A cell, which has
high signal strength and heavy traffic load, cannot be added to
the active set. This cell enters the soft handover rate reduction
evaluation process repeatedly, which results in rate reduction in
the active set. If the cell fails to be added to the active set, the
rate in the active set increases during the evaluation process
because of the DCCC algorithm. To avoid such rate fluctuation,
the RNC uses the mechanism of rate increase penalty after soft
handover rate reduction fails again.
GUI Value Range: 0~255
Unit: s
Actual Value Range: 0~255
Default Value: 30

DraS
witch

B
S
C
6
9
0
0

ADD
UCE
LLD
CCC
MOD
UCE
LLD
CCC

W
RF
D01
02
02
W
RF
D16

UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LL-

Meaning: 1. DRA_SMART_FAST_STATE_TRANS_SWITCH:
Whether to activate the fast state transition algorithm. When this
switch is turned on, the RNC identifies UEs supporting fast state
transition and then quickly transits the UEs from CELL_DCH to
CELL_FACH. 2. DRA_PCH_UE_SMART_P2D_SWITCH:
Whether to activate the algorithm for smart PCH-to-DCH state
transition specific to UEs in the CELL_PCH or URA_PCH state.
When this switch is turned on, the RNC identifies UEs
supporting smart PCH-to-DCH state transition and then transits
the UEs from CELL_PCH or URA_PCH to CELL_DCH. 3.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
14
W
RF
D01
06
11
37

DC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
Loa
dbas
ed
Inte
llig
ent
Stat
e
Tra
nsiti
on

Description

BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH: Whether to
activate the algorithm for setting event 4A threshold for BE
services. This parameter is a cell-level parameter. When this
switch is turned on and the threshold specified in
"BeF2DHTvmThdForFACHCong" is exceeded, the RNC transits
the UEs reporting event 4A from CELL_FACH to CELL_DCH.
When this switch is turned off, the RNC uses original thresholds
in different scenarios. 4. DRA_URA_PCH_SWITCH: Whether
to preferentially transit some UEs to the URA_PCH state. This
switch is a cell-level switch. When this switch is turned on, the
RNC preferentially transits the following UEs to the URA_PCH
state: UEs that are shifted to the current cell from another cell
through cell reselection and UEs that are about to transit from
the CELL_FACH or CELL_DCH state to the CELL_PCH or
URA_PCH state. 5.
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH:
Whether the load based state transition parameters are used for
UEs in a cell. When this switch is set to on and the
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH under
the "DraSwitch2" in the "SET UCORRMALGOSWITCH"
command is set to on for a cell, the following load based state
transition parameters are used for UEs in the cell:
"HiLdBeD2FStateTransTimer" in the "SET
UUESTATETRANSTIMER" command,
"HiLdCellDchPSInactTimer" in the "SET UPSINACTTIMER"
command, and "HiLdBeDLF2DHTvmThd" and
"HiLdBeULF2DETvmThd" in the "SET UUESTATETRANS"
command.
GUI Value Range:
DRA_SMART_FAST_STATE_TRANS_SWITCH,
DRA_PCH_UE_SMART_P2D_SWITCH,
BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH,
DRA_URA_PCH_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH
Unit: None
Actual Value Range:
DRA_SMART_FAST_STATE_TRANS_SWITCH,
DRA_PCH_UE_SMART_P2D_SWITCH,
BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

DRA_URA_PCH_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH
Default Value:
DRA_SMART_FAST_STATE_TRANS_SWITCH:0,DRA_PCH
_UE_SMART_P2D_SWITCH:0,BE_4A_THD_ADJ_FOR_FAC
H_CONG_SWITCH:0,DRA_URA_PCH_SWITCH:0,DRA_IN
TELL_STATE_TRANS_ON_LOAD_SWITCH:0
DraS
witch

B
S
C
6
9
1
0

ADD
UCE
LLD
CCC
MOD
UCE
LLD
CCC

W
RF
D01
02
02
W
RF
D16
02
14
W
RF
D01
06
11
37

UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LLDC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
Loa
dbas
ed
Inte
llig
ent

Meaning: 1. DRA_SMART_FAST_STATE_TRANS_SWITCH:
Whether to activate the fast state transition algorithm. When this
switch is turned on, the RNC identifies UEs supporting fast state
transition and then quickly transits the UEs from CELL_DCH to
CELL_FACH. 2. DRA_PCH_UE_SMART_P2D_SWITCH:
Whether to activate the algorithm for smart PCH-to-DCH state
transition specific to UEs in the CELL_PCH or URA_PCH state.
When this switch is turned on, the RNC identifies UEs
supporting smart PCH-to-DCH state transition and then transits
the UEs from CELL_PCH or URA_PCH to CELL_DCH. 3.
BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH: Whether to
activate the algorithm for setting event 4A threshold for BE
services. This parameter is a cell-level parameter. When this
switch is turned on and the threshold specified in
"BeF2DHTvmThdForFACHCong" is exceeded, the RNC transits
the UEs reporting event 4A from CELL_FACH to CELL_DCH.
When this switch is turned off, the RNC uses original thresholds
in different scenarios. 4. DRA_URA_PCH_SWITCH: Whether
to preferentially transit some UEs to the URA_PCH state. This
switch is a cell-level switch. When this switch is turned on, the
RNC preferentially transits the following UEs to the URA_PCH
state: UEs that are shifted to the current cell from another cell
through cell reselection and UEs that are about to transit from
the CELL_FACH or CELL_DCH state to the CELL_PCH or
URA_PCH state. 5.
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH:
Whether the load based state transition parameters are used for
UEs in a cell. When this switch is set to on and the
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH under
the "DraSwitch2" in the "SET UCORRMALGOSWITCH"
command is set to on for a cell, the following load based state

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

DraS B SET
witch2 S UCO
C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D01
02
02
W
RF
D02
11
01

Description

Stat
e
Tra
nsiti
on

transition parameters are used for UEs in the cell:


"HiLdBeD2FStateTransTimer" in the "SET
UUESTATETRANSTIMER" command,
"HiLdCellDchPSInactTimer" in the "SET UPSINACTTIMER"
command, and "HiLdBeDLF2DHTvmThd" and
"HiLdBeULF2DETvmThd" in the "SET UUESTATETRANS"
command.
GUI Value Range:
DRA_SMART_FAST_STATE_TRANS_SWITCH,
DRA_PCH_UE_SMART_P2D_SWITCH,
BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH,
DRA_URA_PCH_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH
Unit: None
Actual Value Range:
DRA_SMART_FAST_STATE_TRANS_SWITCH,
DRA_PCH_UE_SMART_P2D_SWITCH,
BE_4A_THD_ADJ_FOR_FACH_CONG_SWITCH,
DRA_URA_PCH_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH
Default Value:
DRA_SMART_FAST_STATE_TRANS_SWITCH:0,DRA_PCH
_UE_SMART_P2D_SWITCH:0,BE_4A_THD_ADJ_FOR_FAC
H_CONG_SWITCH:0,DRA_URA_PCH_SWITCH:0,DRA_IN
TELL_STATE_TRANS_ON_LOAD_SWITCH:0

UE
Stat
e in
Con
nect
ed
Mo
de
(CE
LLDC
H,
CE

Meaning: 1.
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH:
When this switch is turned on, the RNC decides the HSUPA
bearer policy for the UE state transition from CELL_FACH,
CELL_PCH, or URA_PCH to CELL_DCH based on the
obtained valid Ec/No value. If the Ec/No value is greater than the
value of "EcN0ThdForBaseCoverE2D" in the "SET UFRC"
command, the BE services are set up on the E-DCH. Otherwise,
the BE services are set up on the DCH. 2.
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH: When
this switch is turned on, the RNC immediately updates the PCPICH Ec/N0 value if the "Measured results on RACH" IE
carries the measured P-CPICH Ec/N0 value in event 4A or event

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D01
06
12
W
RF
D16
02
14

LLPC
H,
UR
APC
H,
CE
LLFA
CH)
Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
HS
UP
A
Intr
odu
ctio
n
Pac
kag
e
Loa
dbas
ed
Inte

Description

4B. In addition, the updated P-CPICH Ec/N0 value is used for


decisions on coverage-based TTI selection and coverage-based
E2D for UEs with RRC connections. 3.
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH: Whether
the initial establishing BE service of a UE is switched from
HSUPA channels to R99 channels in weak coverage areas. When
this switch is turned off, the BE service of the UE is not switched
from HSUPA channels to R99 channels in weak coverage areas.
When this switch is turned on, the BE service of the UE is
switched from HSUPA channels to R99 channels in weak
coverage areas. Note: When the Ec/No in the RACH
measurement report from the UE is less than or equal to the
value of "EcN0ThdForBaseCoverE2D" in the "SET UFRC"
command, the UE is in the weak coverage area. 4.
DRA_BASE_COVER_BE_E2D_SWITCH: Whether BE
services can be switched over from HSUPA to R99 due to
insufficient coverage in connected mode. When this switch is
turned on, BE services can be switched over from HSUPA to
R99 due to insufficient coverage. If the coverage recovers after
the UE moves to the cell center and the throughput is high, the
BE services can be transferred to HSUPA. Note: When event
6A1 is reported, the UE is in connected mode under weak
coverage. 5. DRA_D2F_OVER_IUR_SWITCH: Whether to
trigger D2F state transition when no CCCH is configured over
the Iur interface and an Iur link is established. When this switch
is turned off, the RNC does not trigger the D2F procedure over
the Iur interface if no CCCH is configured over the Iur interface.
When this switch is turned on, the D2F procedure is triggered
regardless of the existence of the CCCH over the Iur interface. 6.
DRA_CSPS_0K_RATE_UP_SWITCH: Whether the PS BE
service in the CS+PS BE combined service supports event-4Atriggered DCCC data rate increasing when its data rate is 0
kbit/s. ON: This switch is turned on. The PS BE service in the
CS+PS BE combined service supports event-4A-triggered
DCCC data rate increasing when its data rate is 0 kbit/s. OFF:
This switch is turned off. The PS BE service in the CS+PS BE
combined service does not support event-4A-triggered DCCC
data rate increasing when its data rate is 0 kbit/s. 7.
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH: Whether the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
llig
ent
Stat
e
Tra
nsiti
on

Description

PS BE service in the CS+PS BE combined service supports


DCCC data rate increasing on both the uplink and the downlink
when an event 4A is reported on the uplink or downlink. ON:
This switch is turned on. The PS BE service supports DCCC data
rate increasing on both the uplink and the downlink when event
4A is reported on the uplink or downlink. OFF: This switch is
turned off. The PS BE service does not support DCCC data rate
increasing on both the uplink and the downlink when event 4A is
reported on the uplink or downlink. 8.
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH:
Whether the following two functions can be enabled:If the
current rate of the PS BE service is 0 kbit/s and event 4A
triggered-DCCC service rate increasing fails for a CS+PS BE
combined service, the RNC does not release the PS BE service
after a timer set by the "ZeroRateUpFailToRelTimerLen"
parameter in the "SET UCOIFTIMER" command expires. A UE
processing a CS+PS BE combined service immediately transits
to the CELL_FACH state if the CS service is released and the PS
BE service has no data transmission. ON: This switch is turned
on. The preceding functions can be enabled. OFF: This switch is
turned off. The preceding functions are disabled. 9.
DRA_BASE_COVER_E2D_DCCC_SWITCH: Whether to use
the DCCC function to increase the DCH data rate for a UE that
has experienced a coverage-triggered E-DCH-to-DCH channel
fallback when the UE's transmit power or the cell's RSCP does
not meet the E-DCH allocation requirement. When this
parameter is set to ON, the implementation is allowed but the
maximum data rate is 144 kbit/s. When this parameter is set to
OFF, the implementation is prohibited. In addition, before DCHto-E-DCH channel switching, the DCH data rate of the UE is
fixed at the value of the "UlBeTraffInitBitrate" parameter in the
"SET UFRC" command.For a UE that has experienced an
Ec/N0-triggered E-DCH-to-DCH channel fallback during a
service setup, when the
DRA_BASE_COVER_BE_E2D_SWITCH under the
"DraSwitch2" parameter in the "SET
UCORRMALGOSWITCH" command is turned off, the RNC
uses the DCCC function to increase the DCH data rate for the
UE even if the UE's transmit power or the cell's RSCP does not

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

meet the E-DCH allocation requirement. Moreover, the


maximum data rate is configurable and it can be greater than 144
kbit/s. The implementation is not under the control of the
DRA_BASE_COVER_E2D_DCCC_SWITCH. 10.
DRA_WEB_FACH_DELAY_OPT_SWITCH: Whether to
enable the fast CELL_FACH-to-CELL_DCH state transition
function and allow the FACH to transmit the remaining data
when a UE is browsing web pages. Upon detecting that a UE in
the CELL_FACH state is browsing web pages, the RNC transits
the UE to the CELL_DCH state when this switch is turned on. In
addition, the RNC allows the FACH to continue to transmit data
until the state transition is completed. 11.
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH: Whether to
check whether there is an Iu-CS connection before performing a
CELL_DCH-to-CELL_FACH (D2F) state transition. When this
switch is turned on, the RNC checks whether there is an Iu-CS
connection before performing a D2F state transition. If so, the
RNC does not perform the state transition. If not, the RNC
performs the state transition. When this switch is turned off, the
RNC does not check whether there is an Iu-CS connection before
performing the state transition. 12.
DRA_D2P_WHEN_PS_INACT_SWITCH: Switch controlling
the PS-inactivity-based CELL_DCH-to-CELL_PCH (D2P) state
transition algorithm. When this switch is turned on, this
algorithm is activated. When this switch is turned off, this
algorithm is not activated. This algorithm works as follows:After
a UE enters the CELL_DCH state, this algorithm triggers a D2P
state transition upon detecting that the UE does not process any
uplink or downlink service during a certain period of time, which
is specified by the "D2PPsInactTimer " parameter in the "SET
UUESTATETRANSTIMER" command. 13.
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH:
Whether to validate the load based intelligent state transition
algorithm. When this switch is set to on and the
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH under
the "DraSwitch" parameter in the "ADD UCELLDCCC"
command is set to on, the RNC performs state transition
according to the following parameters:
"HiLdBeD2FStateTransTimer" in the "SET

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UUESTATETRANSTIMER" command,
"HiLdCellDchPSInactTimer" in the "SET UPSINACTTIMER"
command, and "HiLdBeDLF2DHTvmThd" and
"HiLdBeULF2DETvmThd" in the "SET UUESTATETRANS"
command. 14.
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH: Whether
the coverage-based and load-based algorithm for dynamic
reconfiguration of the channel mapped to downlink signaling
radio bearers (SRBs) takes effect.When this switch is turned off,
the algorithm does not take effect. When this switch is turned on,
The algorithm takes effect. Operations of the algorithm: 1.
Access mode: The algorithm also considers coverage and loads
to determine whether the downlink SRBs can be carried on the
HS-DSCH when a UE transits from the idle, CELL_FACH,
CELL_PCH, or URA_PCH state to the CELL_DCH state during
an RRC connection setup, RAB setup, or RAB modification or
when a CELL_DCH UE experiences an incoming inter-RAT
handover or an incoming combined hard handover and SRNS
relocation. 2. Connected mode: After a UE accesses a cell, the
algorithm determines whether to deliver periodic RSCP and
Ec/N0 measurement control messages. When the RNC receives
periodic measurement reports on the RSCP and Ec/N0, the
algorithm determines whether to initiate the SRB reconfiguration
process.
GUI Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH,
DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH,
DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Unit: None
Actual Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH,
DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH,
DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Default Value:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH:0,D
RA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH:0,DRA_
BASE_COVER_BE_E2D_INITSEL_SWITCH:0,DRA_BASE_
COVER_BE_E2D_SWITCH:0,DRA_D2F_OVER_IUR_SWIT
CH:0,DRA_CSPS_0K_RATE_UP_SWITCH:1,DRA_CSPS_BO
TH_ULDL_RATE_UP_SWITCH:0,DRA_PS_STATE_TRANS_
WHEN_CS_REL_SWITCH:0,DRA_BASE_COVER_E2D_DC
CC_SWITCH:0,DRA_WEB_FACH_DELAY_OPT_SWITCH:0,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH:0,DRA_D2
P_WHEN_PS_INACT_SWITCH:0,DRA_INTELL_STATE_TR
ANS_ON_LOAD_SWITCH:0,DRA_BASE_COVER_LOAD_S
RB_H2D_SWITCH:0
DraS B SET
witch2 S UCO
C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D01
02
02
W
RF
D-

UE
Stat
e in
Con
nect
ed
Mo
de
(CE

Meaning: 1.
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH:
When this switch is turned on, the RNC decides the HSUPA
bearer policy for the UE state transition from CELL_FACH,
CELL_PCH, or URA_PCH to CELL_DCH based on the
obtained valid Ec/No value. If the Ec/No value is greater than the
value of "EcN0ThdForBaseCoverE2D" in the "SET UFRC"
command, the BE services are set up on the E-DCH. Otherwise,
the BE services are set up on the DCH. 2.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
11
01
W
RF
D01
06
12
W
RF
D16
02
14

LLDC
H,
CE
LLPC
H,
UR
APC
H,
CE
LLFA
CH)
Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
HS
UP
A
Intr
odu
ctio
n
Pac
kag
e
Loa

Description

DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH: When
this switch is turned on, the RNC immediately updates the PCPICH Ec/N0 value if the "Measured results on RACH" IE
carries the measured P-CPICH Ec/N0 value in event 4A or event
4B. In addition, the updated P-CPICH Ec/N0 value is used for
decisions on coverage-based TTI selection and coverage-based
E2D for UEs with RRC connections. 3.
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH: Whether
the initial establishing BE service of a UE is switched from
HSUPA channels to R99 channels in weak coverage areas. When
this switch is turned off, the BE service of the UE is not switched
from HSUPA channels to R99 channels in weak coverage areas.
When this switch is turned on, the BE service of the UE is
switched from HSUPA channels to R99 channels in weak
coverage areas. Note: When the Ec/No in the RACH
measurement report from the UE is less than or equal to the
value of "EcN0ThdForBaseCoverE2D" in the "SET UFRC"
command, the UE is in the weak coverage area. 4.
DRA_BASE_COVER_BE_E2D_SWITCH: Whether BE
services can be switched over from HSUPA to R99 due to
insufficient coverage in connected mode. When this switch is
turned on, BE services can be switched over from HSUPA to
R99 due to insufficient coverage. If the coverage recovers after
the UE moves to the cell center and the throughput is high, the
BE services can be transferred to HSUPA. Note: When event
6A1 is reported, the UE is in connected mode under weak
coverage. 5. DRA_D2F_OVER_IUR_SWITCH: Whether to
trigger D2F state transition when no CCCH is configured over
the Iur interface and an Iur link is established. When this switch
is turned off, the RNC does not trigger the D2F procedure over
the Iur interface if no CCCH is configured over the Iur interface.
When this switch is turned on, the D2F procedure is triggered
regardless of the existence of the CCCH over the Iur interface. 6.
DRA_CSPS_0K_RATE_UP_SWITCH: Whether the PS BE
service in the CS+PS BE combined service supports event-4Atriggered DCCC data rate increasing when its data rate is 0
kbit/s. ON: This switch is turned on. The PS BE service in the
CS+PS BE combined service supports event-4A-triggered
DCCC data rate increasing when its data rate is 0 kbit/s. OFF:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
dbas
ed
Inte
llig
ent
Stat
e
Tra
nsiti
on

Description

This switch is turned off. The PS BE service in the CS+PS BE


combined service does not support event-4A-triggered DCCC
data rate increasing when its data rate is 0 kbit/s. 7.
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH: Whether the
PS BE service in the CS+PS BE combined service supports
DCCC data rate increasing on both the uplink and the downlink
when an event 4A is reported on the uplink or downlink. ON:
This switch is turned on. The PS BE service supports DCCC data
rate increasing on both the uplink and the downlink when event
4A is reported on the uplink or downlink. OFF: This switch is
turned off. The PS BE service does not support DCCC data rate
increasing on both the uplink and the downlink when event 4A is
reported on the uplink or downlink. 8.
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH:
Whether the following two functions can be enabled:If the
current rate of the PS BE service is 0 kbit/s and event 4A
triggered-DCCC service rate increasing fails for a CS+PS BE
combined service, the RNC does not release the PS BE service
after a timer set by the "ZeroRateUpFailToRelTimerLen"
parameter in the "SET UCOIFTIMER" command expires. A UE
processing a CS+PS BE combined service immediately transits
to the CELL_FACH state if the CS service is released and the PS
BE service has no data transmission. ON: This switch is turned
on. The preceding functions can be enabled. OFF: This switch is
turned off. The preceding functions are disabled. 9.
DRA_BASE_COVER_E2D_DCCC_SWITCH: Whether to use
the DCCC function to increase the DCH data rate for a UE that
has experienced a coverage-triggered E-DCH-to-DCH channel
fallback when the UE's transmit power or the cell's RSCP does
not meet the E-DCH allocation requirement. When this
parameter is set to ON, the implementation is allowed but the
maximum data rate is 144 kbit/s. When this parameter is set to
OFF, the implementation is prohibited. In addition, before DCHto-E-DCH channel switching, the DCH data rate of the UE is
fixed at the value of the "UlBeTraffInitBitrate" parameter in the
"SET UFRC" command.For a UE that has experienced an
Ec/N0-triggered E-DCH-to-DCH channel fallback during a
service setup, when the
DRA_BASE_COVER_BE_E2D_SWITCH under the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

"DraSwitch2" parameter in the "SET


UCORRMALGOSWITCH" command is turned off, the RNC
uses the DCCC function to increase the DCH data rate for the
UE even if the UE's transmit power or the cell's RSCP does not
meet the E-DCH allocation requirement. Moreover, the
maximum data rate is configurable and it can be greater than 144
kbit/s. The implementation is not under the control of the
DRA_BASE_COVER_E2D_DCCC_SWITCH. 10.
DRA_WEB_FACH_DELAY_OPT_SWITCH: Whether to
enable the fast CELL_FACH-to-CELL_DCH state transition
function and allow the FACH to transmit the remaining data
when a UE is browsing web pages. Upon detecting that a UE in
the CELL_FACH state is browsing web pages, the RNC transits
the UE to the CELL_DCH state when this switch is turned on. In
addition, the RNC allows the FACH to continue to transmit data
until the state transition is completed. 11.
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH: Whether to
check whether there is an Iu-CS connection before performing a
CELL_DCH-to-CELL_FACH (D2F) state transition. When this
switch is turned on, the RNC checks whether there is an Iu-CS
connection before performing a D2F state transition. If so, the
RNC does not perform the state transition. If not, the RNC
performs the state transition. When this switch is turned off, the
RNC does not check whether there is an Iu-CS connection before
performing the state transition. 12.
DRA_D2P_WHEN_PS_INACT_SWITCH: Switch controlling
the PS-inactivity-based CELL_DCH-to-CELL_PCH (D2P) state
transition algorithm. When this switch is turned on, this
algorithm is activated. When this switch is turned off, this
algorithm is not activated. This algorithm works as follows:After
a UE enters the CELL_DCH state, this algorithm triggers a D2P
state transition upon detecting that the UE does not process any
uplink or downlink service during a certain period of time, which
is specified by the "D2PPsInactTimer " parameter in the "SET
UUESTATETRANSTIMER" command. 13.
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH:
Whether to validate the load based intelligent state transition
algorithm. When this switch is set to on and the
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH under

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

the "DraSwitch" parameter in the "ADD UCELLDCCC"


command is set to on, the RNC performs state transition
according to the following parameters:
"HiLdBeD2FStateTransTimer" in the "SET
UUESTATETRANSTIMER" command,
"HiLdCellDchPSInactTimer" in the "SET UPSINACTTIMER"
command, and "HiLdBeDLF2DHTvmThd" and
"HiLdBeULF2DETvmThd" in the "SET UUESTATETRANS"
command. 14.
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH: Whether
the coverage-based and load-based algorithm for dynamic
reconfiguration of the channel mapped to downlink signaling
radio bearers (SRBs) takes effect.When this switch is turned off,
the algorithm does not take effect. When this switch is turned on,
The algorithm takes effect. Operations of the algorithm: 1.
Access mode: The algorithm also considers coverage and loads
to determine whether the downlink SRBs can be carried on the
HS-DSCH when a UE transits from the idle, CELL_FACH,
CELL_PCH, or URA_PCH state to the CELL_DCH state during
an RRC connection setup, RAB setup, or RAB modification or
when a CELL_DCH UE experiences an incoming inter-RAT
handover or an incoming combined hard handover and SRNS
relocation. 2. Connected mode: After a UE accesses a cell, the
algorithm determines whether to deliver periodic RSCP and
Ec/N0 measurement control messages. When the RNC receives
periodic measurement reports on the RSCP and Ec/N0, the
algorithm determines whether to initiate the SRB reconfiguration
process.
GUI Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH,
DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH,
DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Unit: None
Actual Value Range:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH,
DRA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH,
DRA_BASE_COVER_BE_E2D_INITSEL_SWITCH,
DRA_BASE_COVER_BE_E2D_SWITCH,
DRA_D2F_OVER_IUR_SWITCH,
DRA_CSPS_0K_RATE_UP_SWITCH,
DRA_CSPS_BOTH_ULDL_RATE_UP_SWITCH,
DRA_PS_STATE_TRANS_WHEN_CS_REL_SWITCH,
DRA_BASE_COVER_E2D_DCCC_SWITCH,
DRA_WEB_FACH_DELAY_OPT_SWITCH,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH,
DRA_D2P_WHEN_PS_INACT_SWITCH,
DRA_INTELL_STATE_TRANS_ON_LOAD_SWITCH,
DRA_BASE_COVER_LOAD_SRB_H2D_SWITCH
Default Value:
DRA_BASE_COVER_BE_E2D_INITSEL_OPT_SWITCH:0,D
RA_PCPICH_ECN0_ON_RACH_UPDATE_SWITCH:0,DRA_
BASE_COVER_BE_E2D_INITSEL_SWITCH:0,DRA_BASE_
COVER_BE_E2D_SWITCH:0,DRA_D2F_OVER_IUR_SWIT
CH:0,DRA_CSPS_0K_RATE_UP_SWITCH:1,DRA_CSPS_BO
TH_ULDL_RATE_UP_SWITCH:0,DRA_PS_STATE_TRANS_
WHEN_CS_REL_SWITCH:0,DRA_BASE_COVER_E2D_DC
CC_SWITCH:0,DRA_WEB_FACH_DELAY_OPT_SWITCH:0,
DRA_D2F_LIMIT_WITH_CS_IU_CON_SWITCH:0,DRA_D2
P_WHEN_PS_INACT_SWITCH:0,DRA_INTELL_STATE_TR
ANS_ON_LOAD_SWITCH:0,DRA_BASE_COVER_LOAD_S
RB_H2D_SWITCH:0
IntraF B ADD
reqFilt S UCE
erCoef C LLIN
6 TRAF
9 REQ

W
RF
D02
02

Inte
r
RN
C
Soft

Meaning: This parameter specifies the Layer 3 filter coefficient


for the intra-frequency measurement. According to 3GPP TS
25.331, the filtered measurement value is calculated using the
following formula, where k represents this parameter: Fn = (1 a) * Fn - 1 + a * Mn a = 1/(2 ^ (k/2)) Here, Fn: filtered

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

03
W
RF
D02
02
02

Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

measurement result Fn - 1: previously filtered measurement


result Mn: latest received measurement result from physical
layer When a is set to 1, L3 filtering is not applied. The input
measurement value to L3 filter has been filtered by L1 filter,
where the impact of fast fading is almost eliminated. In this case,
smooth filtering should be applied through L3 filter, to eliminate
the effect of shadow fading and peaks caused by fast fading, thus
the filtered measurement value can reflect the variation of the
actual measurement value, and provide more reliable
measurement result for event judgement. Note that this
parameter has great impact on the overall performance of the
handover. Therefore, set this parameter with caution.
GUI Value Range: D0, D1, D2, D3, D4, D5, D6, D7, D8, D9,
D11, D13, D15, D17, D19
Unit: None
Actual Value Range: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19
Default Value: D3

IntraF B ADD
reqFilt S UCE
erCoef C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the Layer 3 filter coefficient


for the intra-frequency measurement. According to 3GPP TS
25.331, the filtered measurement value is calculated using the
following formula, where k represents this parameter: Fn = (1 a) * Fn - 1 + a * Mn a = 1/(2 ^ (k/2)) Here, Fn: filtered
measurement result Fn - 1: previously filtered measurement
result Mn: latest received measurement result from physical
layer When a is set to 1, L3 filtering is not applied. The input
measurement value to L3 filter has been filtered by L1 filter,
where the impact of fast fading is almost eliminated. In this case,
smooth filtering should be applied through L3 filter, to eliminate
the effect of shadow fading and peaks caused by fast fading, thus
the filtered measurement value can reflect the variation of the
actual measurement value, and provide more reliable
measurement result for event judgement. Note that this
parameter has great impact on the overall performance of the
handover. Therefore, set this parameter with caution.
GUI Value Range: D0, D1, D2, D3, D4, D5, D6, D7, D8, D9,
D11, D13, D15, D17, D19
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19


Default Value: D3
RsvU
32Par
a8

B
S
C
6
9
0
0

SET No Non
UAL ne e
GOR
SVPA
RA

Meaning: RRM algorithm reserved U32 para 8. The 32-bit


parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: 0~4294967295
Unit: None
Actual Value Range: 0~4294967295
Default Value: 0

RsvU
32Par
a8

B
S
C
6
9
1
0

SET No Non
UAL ne e
GOR
SVPA
RA

Meaning: RRM algorithm reserved U32 para 8. The 32-bit


parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: 0~4294967295
Unit: None
Actual Value Range: 0~4294967295
Default Value: 0

CsHo
PrioM
easTi
merLe
n

B
S
C
6
9
0
0

SET
UHO
COM
M

Meaning: Interval between an inter-frequency measurement


control message for CS services and an inter-RAT measurement
control message for CS services. When a UE in compressed
mode is processing a CS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

CsHo
PrioM
easTi
merLe
n

B
S
C
6
9
1
0

SET
UHO
COM
M

W
RF
D02
03
02
W
RF
D02
03
03

Description

Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

GUI Value Range: 0~60


Unit: s
Actual Value Range: 0~60
Default Value: 0

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov

Meaning: Interval between an inter-frequency measurement


control message for CS services and an inter-RAT measurement
control message for CS services. When a UE in compressed
mode is processing a CS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Bas
ed
on
Cov
erag
e
PsHoP
rioMe
asTim
erLen

B
S
C
6
9
0
0

SET
UHO
COM
M

PsHoP B SET

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Interval between an inter-frequency measurement


control message for PS services and an inter-RAT measurement
control message for PS services. When a UE in compressed
mode is processing a PS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

W Inte Meaning: Interval between an inter-frequency measurement

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

rioMe S UHO RF
asTim C COM DerLen 6 M
02
9
03
1
02
0
W
RF
D02
03
03

r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

control message for PS services and an inter-RAT measurement


control message for PS services. When a UE in compressed
mode is processing a PS service and is about to perform an interRAT or inter-frequency handover, the RNC preferentially sends
the UE an inter-frequency measurement control message. If no
qualified cells are available or the inter-frequency handover fails
but the timer expires, the RNC sends the UE an inter-RAT
measurement control message to instruct the UE to measure
signal quality of inter-RAT neighboring cells. When this
parameter is set to 0, the RNC sends the UE the inter-frequency
measurement control and inter-RAT measurement control
messages at the same time.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
Default Value: 0

InterF
reqRe
portM
ode

Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Cell-oriented inter-frequency measurement report


mode. If this parameter is set to PERIODICAL_REPORTING,
measurement reports are periodically reported. If this parameter
is set to EVENT_TRIGGER, measurement reports are reported
by triggering the event. There are two inter-frequency handover
report modes in the RNC, namely, event-triggered report and
periodical report. The report mode is selected by setting the
inter-frequency report mode switch that is RNC-oriented.
GUI Value Range: PERIODICAL_REPORTING(Periodical
reporting), EVENT_TRIGGER(Event trigger)

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN

W
RF
D02
03
02

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
TERF
REQ
HOC
OV

Description

Bas
ed
on
Cov
erag
e

Unit: None
Actual Value Range: PERIODICAL_REPORTING,
EVENT_TRIGGER
Default Value: PERIODICAL_REPORTING(Periodical
reporting)

InterF
reqRe
portM
ode

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Cell-oriented inter-frequency measurement report


mode. If this parameter is set to PERIODICAL_REPORTING,
measurement reports are periodically reported. If this parameter
is set to EVENT_TRIGGER, measurement reports are reported
by triggering the event. There are two inter-frequency handover
report modes in the RNC, namely, event-triggered report and
periodical report. The report mode is selected by setting the
inter-frequency report mode switch that is RNC-oriented.
GUI Value Range: PERIODICAL_REPORTING(Periodical
reporting), EVENT_TRIGGER(Event trigger)
Unit: None
Actual Value Range: PERIODICAL_REPORTING,
EVENT_TRIGGER
Default Value: PERIODICAL_REPORTING(Periodical
reporting)

InterR
atRep
ortMo
de

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Inter-RAT measurement reporting mode. If this


parameter is set to PERIODICAL_REPORTING, periodic
reporting is used for inter-RAT measurements. If this parameter
is set to EVENT_TRIGGER, event-triggered reporting is used
for inter-RAT measurements. The RNC provides two inter-RAT
measurement reporting modes, event-triggered reporting and
periodic reporting. Which reporting mode is used depends on the
value of "InterRatReportMode".
GUI Value Range: PERIODICAL_REPORTING(Periodical
reporting), EVENT_TRIGGER(Event trigger)
Unit: None
Actual Value Range: PERIODICAL_REPORTING,
EVENT_TRIGGER
Default Value: PERIODICAL_REPORTING(Periodical
reporting)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
InterR
atRep
ortMo
de

B
S
C
6
9
1
0

Description

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Inter-RAT measurement reporting mode. If this


parameter is set to PERIODICAL_REPORTING, periodic
reporting is used for inter-RAT measurements. If this parameter
is set to EVENT_TRIGGER, event-triggered reporting is used
for inter-RAT measurements. The RNC provides two inter-RAT
measurement reporting modes, event-triggered reporting and
periodic reporting. Which reporting mode is used depends on the
value of "InterRatReportMode".
GUI Value Range: PERIODICAL_REPORTING(Periodical
reporting), EVENT_TRIGGER(Event trigger)
Unit: None
Actual Value Range: PERIODICAL_REPORTING,
EVENT_TRIGGER
Default Value: PERIODICAL_REPORTING(Periodical
reporting)

PrdRe B ADD
portInt S UCE
erval C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
04
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir

Meaning: Interval between periodic measurement reports on an


inter-frequency neighboring cell sent from a UE to the RNC. In
periodic reporting mode, the UE sends measurement reports to
the RNC at the preset interval. It is recommended not to set this
parameter to NON_PERIODIC_REPORT. Otherwise, the UE
behavior is unknown.
GUI Value Range: NON_PERIODIC_REPORT(Non periodical
reporting), D250(D250), D500(D500), D1000(D1000),
D2000(D2000), D3000(D3000), D4000(D4000),
D6000(D6000), D8000(D8000), D12000(D12000),
D16000(D16000), D20000(D20000), D24000(D24000),
D28000(D28000), D32000(D32000), D64000(D64000)
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000,
24000, 28000, 32000, 64000
Default Value: D500(D500)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ect
Retr
y
PrdRe B ADD
portInt S UCE
erval C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
04
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Meaning: Interval between periodic measurement reports on an


inter-frequency neighboring cell sent from a UE to the RNC. In
periodic reporting mode, the UE sends measurement reports to
the RNC at the preset interval. It is recommended not to set this
parameter to NON_PERIODIC_REPORT. Otherwise, the UE
behavior is unknown.
GUI Value Range: NON_PERIODIC_REPORT(Non periodical
reporting), D250(D250), D500(D500), D1000(D1000),
D2000(D2000), D3000(D3000), D4000(D4000),
D6000(D6000), D8000(D8000), D12000(D12000),
D16000(D16000), D20000(D20000), D24000(D24000),
D28000(D28000), D32000(D32000), D64000(D64000)
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000,
24000, 28000, 32000, 64000
Default Value: D500(D500)

InterR
ATPer
iodRe
portInt
erval

W
RF
D02
03
09
W
RF

Inte
rRA
T
Han
dov
er
Bas

Meaning: Interval that the UE reports inter-RAT measurement


results to the RNC. This parameter specifies the interval that the
UE sends inter-RAT measurement results to the RNC in
periodical reporting mode. It is not recommended that this
parameter is set to NON_PERIODIC_REPORT since the UE
behavior may be unknown. The GSM RSSI measurement period
is 480 ms. Therefore, the inter-RAT periodical reporting interval
should be longer than 480 ms. If the periodical reporting interval

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UCE
LLIN
TERR
ATH
OCO
V

D02
03
03
W
RF
D02
04
02

ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

is excessively high, the handover decision time will be long, and


handovers will be slow. The adjustment should be made
according to the configured GSM RSSI measurement
compressed mode sequence. According to the current configured
GSM RSSI measurement compressed mode sequence, the RSSI
measurement of eight GSM cells can be finished in 480 ms.
Therefore, the RSSI measurement of 16 GSM cells can be
finished in 1000 ms. According to 3GPP specifications, the
number of inter-RAT neighboring cells should not exceed 32.
Therefore, the parameter value can be set to 2000 ms if the
number of neighboring GSM cells exceeds 16.
GUI Value Range: NON_PERIODIC_REPORT(Non periodical
reporting), D250(D250), D500(D500), D1000(D1000),
D2000(D2000), D3000(D3000), D4000(D4000),
D6000(D6000), D8000(D8000), D12000(D12000),
D16000(D16000), D20000(D20000), D24000(D24000),
D28000(D28000), D32000(D32000), D64000(D64000)
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000,
24000, 28000, 32000, 64000
Default Value: D1000(D1000)

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN

W
RF
D02
03
09
W
RF
D02

Inte
rRA
T
Han
dov
er
Bas
ed
on

Meaning: Interval that the UE reports inter-RAT measurement


results to the RNC. This parameter specifies the interval that the
UE sends inter-RAT measurement results to the RNC in
periodical reporting mode. It is not recommended that this
parameter is set to NON_PERIODIC_REPORT since the UE
behavior may be unknown. The GSM RSSI measurement period
is 480 ms. Therefore, the inter-RAT periodical reporting interval
should be longer than 480 ms. If the periodical reporting interval
is excessively high, the handover decision time will be long, and
handovers will be slow. The adjustment should be made

InterR
ATPer
iodRe
portInt
erval

B
S
C
6
9
1
0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

TERR
ATH
OCO
V

03
03
W
RF
D02
04
02

DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

according to the configured GSM RSSI measurement


compressed mode sequence. According to the current configured
GSM RSSI measurement compressed mode sequence, the RSSI
measurement of eight GSM cells can be finished in 480 ms.
Therefore, the RSSI measurement of 16 GSM cells can be
finished in 1000 ms. According to 3GPP specifications, the
number of inter-RAT neighboring cells should not exceed 32.
Therefore, the parameter value can be set to 2000 ms if the
number of neighboring GSM cells exceeds 16.
GUI Value Range: NON_PERIODIC_REPORT(Non periodical
reporting), D250(D250), D500(D500), D1000(D1000),
D2000(D2000), D3000(D3000), D4000(D4000),
D6000(D6000), D8000(D8000), D12000(D12000),
D16000(D16000), D20000(D20000), D24000(D24000),
D28000(D28000), D32000(D32000), D64000(D64000)
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000, 20000,
24000, 28000, 32000, 64000
Default Value: D1000(D1000)

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag

Meaning: Threshold of triggering inter-RAT measurements for


CS services when RSCP is used as the measurement quantity. If
the measured RSCP value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.

InterR
ATCS
Thd2
DRSC
P

B
S
C
6
9
0
0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
OCO
V

Description

GUI Value Range: -115~-25


Unit: dBm
Actual Value Range: -115~-25
Default Value: -100

InterR
ATCS
Thd2
DRSC
P

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurements for


CS services when RSCP is used as the measurement quantity. If
the measured RSCP value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -100

InterF
reqCS
Thd2
DRSC
P

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of triggering the inter-frequency


measurement for CS services. When RSCP is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2D if the measured RSCP value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it will be to start the compressed mode. To reduce
the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range: -115~-25


Default Value: -95
InterF
reqCS
Thd2
DRSC
P

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of triggering the inter-frequency


measurement for CS services. When RSCP is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2D if the measured RSCP value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it will be to start the compressed mode. To reduce
the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

Meas
Quanti
tyOf3
A

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Measurement quantity used in coverage-based interRAT measurement in event 3A-triggered reporting mode. If this
parameter is set to CPICH_Ec/N0, the Ec/N0 measurement
quantity is used for event 3A measurements. The physical unit is
dB. If this parameter is set to CPICH_RSCP, the RSCP
measurement quantity is used for event 3A measurements. The
physical unit is dB. If this parameter is set to AUTO, the Ec/N0
measurement quantity is used for event 3A measurements when
the RNC first receives Ec/N0 2D, and the RSCP measurement
quantity is used for event 3A measurements when the RNC first
receives RSCP 2D.
GUI Value Range: CPICH_EC/NO, CPICH_RSCP, AUTO
Unit: None
Actual Value Range: CPICH_EC/NO, CPICH_RSCP, AUTO
Default Value: AUTO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Meas
Quanti
tyOf3
A

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Measurement quantity used in coverage-based interRAT measurement in event 3A-triggered reporting mode. If this
parameter is set to CPICH_Ec/N0, the Ec/N0 measurement
quantity is used for event 3A measurements. The physical unit is
dB. If this parameter is set to CPICH_RSCP, the RSCP
measurement quantity is used for event 3A measurements. The
physical unit is dB. If this parameter is set to AUTO, the Ec/N0
measurement quantity is used for event 3A measurements when
the RNC first receives Ec/N0 2D, and the RSCP measurement
quantity is used for event 3A measurements when the RNC first
receives RSCP 2D.
GUI Value Range: CPICH_EC/NO, CPICH_RSCP, AUTO
Unit: None
Actual Value Range: CPICH_EC/NO, CPICH_RSCP, AUTO
Default Value: AUTO

UsedF
reqMe
asQua
ntityF
orQos
3A

B
S
C
6
9
0
0

ADD
UCE
LLQ
OSH
O
MOD
UCE
LLQ
OSH
O

W
RF
D02
03
09

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: This parameter configures the used frequency


measurement quantity to trigger the inter-RAT measurement for
the purpose of QoS-based handover. The parameter is valid when
the event reporting mode is selected for inter-RAT. Ec/No:
signal-to-noise ratio RSCP: received signal code power
CPICH_Ec/NO: the measurement quantity used for event 2D and
2F, with unit of dB CPICH_RSCP: the measurement quantity
used for event 2D and 2F, with unit of dBm The RNC, in the
coverage-based inter-RAT measurement, may configure that the
inter-RAT measurement quantity are delivered according to
event 2D that triggers the measurement, which causes the result
that the QoS-based inter-RAT measurement cannot refer to the
coverage-based configurations. Under this condition, it is
necessary for the QoS-based inter-RAT measurement to set the
used frequency separately. When both the QoS-based and the
coverage-based inter-RAT measurements exist, refer to this
parameter. As for the impact on network performance: When the
UE moves to the cell border, and there is a intra-frequency
neighboring cell in the moving direction, CPCICH Ec/No varies
faster than RSCP and the quality of the current cell should be
evaluated according to CPCICH Ec/No. When there is no intrafrequency neighboring cell in the direction, CPCICH RSCP
varies faster than Ec/No and the quality should be evaluated

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

according to CPCICH RSCP. If the measurement quantity is not


properly selected, the handover may not be performed timely,
thus resulting in call drops.
GUI Value Range: CPICH_EC/NO, CPICH_RSCP
Unit: None
Actual Value Range: CPICH_EC/NO, CPICH_RSCP
Default Value: CPICH_RSCP
UsedF
reqMe
asQua
ntityF
orQos
3A

B
S
C
6
9
1
0

ADD
UCE
LLQ
OSH
O
MOD
UCE
LLQ
OSH
O

W
RF
D02
03
09

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: This parameter configures the used frequency


measurement quantity to trigger the inter-RAT measurement for
the purpose of QoS-based handover. The parameter is valid when
the event reporting mode is selected for inter-RAT. Ec/No:
signal-to-noise ratio RSCP: received signal code power
CPICH_Ec/NO: the measurement quantity used for event 2D and
2F, with unit of dB CPICH_RSCP: the measurement quantity
used for event 2D and 2F, with unit of dBm The RNC, in the
coverage-based inter-RAT measurement, may configure that the
inter-RAT measurement quantity are delivered according to
event 2D that triggers the measurement, which causes the result
that the QoS-based inter-RAT measurement cannot refer to the
coverage-based configurations. Under this condition, it is
necessary for the QoS-based inter-RAT measurement to set the
used frequency separately. When both the QoS-based and the
coverage-based inter-RAT measurements exist, refer to this
parameter. As for the impact on network performance: When the
UE moves to the cell border, and there is a intra-frequency
neighboring cell in the moving direction, CPCICH Ec/No varies
faster than RSCP and the quality of the current cell should be
evaluated according to CPCICH Ec/No. When there is no intrafrequency neighboring cell in the direction, CPCICH RSCP
varies faster than Ec/No and the quality should be evaluated
according to CPCICH RSCP. If the measurement quantity is not
properly selected, the handover may not be performed timely,
thus resulting in call drops.
GUI Value Range: CPICH_EC/NO, CPICH_RSCP
Unit: None
Actual Value Range: CPICH_EC/NO, CPICH_RSCP
Default Value: CPICH_RSCP

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

HOCo B ADD
vPrio S UINT
C ERFR
6 EQN
9 CELL
0 MOD
0 UINT
ERFR
EQN
CELL

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Priority of a neighboring cell during coverage-based


inter-frequency handovers. Value 0 indicates that the cell does
not support coverage-based inter-frequency handovers. Value 1
indicates that the cell has the highest priority for coverage-based
inter-frequency handovers. Value 3 indicates that the cell has the
lowest priority for coverage-based inter-frequency handovers.
GUI Value Range: 0~3
Unit: None
Actual Value Range: 0~3
Default Value: 2

HOCo B ADD
vPrio S UINT
C ERFR
6 EQN
9 CELL
1 MOD
0 UINT
ERFR
EQN
CELL

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Priority of a neighboring cell during coverage-based


inter-frequency handovers. Value 0 indicates that the cell does
not support coverage-based inter-frequency handovers. Value 1
indicates that the cell has the highest priority for coverage-based
inter-frequency handovers. Value 3 indicates that the cell has the
lowest priority for coverage-based inter-frequency handovers.
GUI Value Range: 0~3
Unit: None
Actual Value Range: 0~3
Default Value: 2

Coexi
stMea
sThdC
hoice

W
RF
D02
03

Inte
r
Fre
que
ncy

Meaning: event 2D/2F measurement threshold of which


measurement type (inter-frequency or inter-RAT measurements)
will be used, when inter-frequency and inter-RAT measurements
coexist. When
COEXIST_MEAS_THD_CHOICE_INTERFREQ is selected,

B
S
C
6
9

ADD
UCE
LLH
OCO
MM

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Coexi
stMea
sThdC
hoice

Description

0 MOD 02
0 UCE W
LLH RF
OCO DMM 02
03
03

Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

event 2D/2F measurement thresholds oriented towards interfrequency configuration are selected. When
COEXIST_MEAS_THD_CHOICE_INTERRAT is selected,
event 2D/2F measurement thresholds oriented towards inter-RAT
configuration are selected.
GUI Value Range:
COEXIST_MEAS_THD_CHOICE_INTERFREQ(Choosing the
inter-frequency oriented parameters),
COEXIST_MEAS_THD_CHOICE_INTERRAT(Choosing the
inter-RAT oriented parameters)
Unit: None
Actual Value Range:
COEXIST_MEAS_THD_CHOICE_INTERFREQ,
COEXIST_MEAS_THD_CHOICE_INTERRAT
Default Value:
COEXIST_MEAS_THD_CHOICE_INTERFREQ(Choosing the
inter-frequency oriented parameters)

B
S
C
6
9
1
0

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: event 2D/2F measurement threshold of which


measurement type (inter-frequency or inter-RAT measurements)
will be used, when inter-frequency and inter-RAT measurements
coexist. When
COEXIST_MEAS_THD_CHOICE_INTERFREQ is selected,
event 2D/2F measurement thresholds oriented towards interfrequency configuration are selected. When
COEXIST_MEAS_THD_CHOICE_INTERRAT is selected,
event 2D/2F measurement thresholds oriented towards inter-RAT
configuration are selected.
GUI Value Range:
COEXIST_MEAS_THD_CHOICE_INTERFREQ(Choosing the
inter-frequency oriented parameters),
COEXIST_MEAS_THD_CHOICE_INTERRAT(Choosing the

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D02
03
02
W
RF
D02
03
03

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

inter-RAT oriented parameters)


Unit: None
Actual Value Range:
COEXIST_MEAS_THD_CHOICE_INTERFREQ,
COEXIST_MEAS_THD_CHOICE_INTERRAT
Default Value:
COEXIST_MEAS_THD_CHOICE_INTERFREQ(Choosing the
inter-frequency oriented parameters)

TimeT B ADD
oTrig2 S UCE
D
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 2D. A UE reports an event


2D measurement report if the conditions for triggering event 2D
are met and persist during the time period specified by this
parameter.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D320

TimeT B ADD
oTrig2 S UCE
D
C LLIN
6 TERF
9 REQ
1 HOC

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har

Meaning: Time delay to trigger event 2D. A UE reports an event


2D measurement report if the conditions for triggering event 2D
are met and persist during the time period specified by this
parameter.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

Description

d
Han
dov
er
Bas
ed
on
Cov
erag
e

Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D320

HystF B ADD
or2D S UCE
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis for triggering event 2D. When


"InterFreqReportMode" is set to PERIODICAL_REPORTING,
the hysteresis in active set quality measurement is used to
prevent the ping-pong reporting of event 2D (triggered when the
estimated quality of the frequency in use is lower than the
threshold) and event 2F (triggered when the estimated quality of
the frequency in use is higher than the threshold). Event 2D is
used to enable the compression mode and event 2F is used to
disable the compression mode.To prevent the compression mode
from being frequently enabled and disabled, you can set
"Hystfor2D" and "Hystfor2F" to be greater than their
recommended values according to the statistics of the ping-pong
inter-frequency handover.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

HystF B ADD
or2D S UCE
C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Hysteresis for triggering event 2D. When


"InterFreqReportMode" is set to PERIODICAL_REPORTING,
the hysteresis in active set quality measurement is used to
prevent the ping-pong reporting of event 2D (triggered when the
estimated quality of the frequency in use is lower than the
threshold) and event 2F (triggered when the estimated quality of
the frequency in use is higher than the threshold). Event 2D is
used to enable the compression mode and event 2F is used to
disable the compression mode.To prevent the compression mode
from being frequently enabled and disabled, you can set

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

TERF
REQ
HOC
OV

Bas
ed
on
Cov
erag
e

"Hystfor2D" and "Hystfor2F" to be greater than their


recommended values according to the statistics of the ping-pong
inter-frequency handover.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

InterF
reqCS
Thd2
DEcN
0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No threshold of triggering the inter-frequency


measurement for CS services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2D if the measured Ec/No value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it will be to start the compressed mode. To reduce
the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterF
reqCS
Thd2
DEcN
0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: Ec/No threshold of triggering the inter-frequency


measurement for CS services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2D if the measured Ec/No value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it will be to start the compressed mode. To reduce

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

REQ
HOC
OV

ed
on
Cov
erag
e

the probability of frequently starting and stopping the


compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterF
reqR9
9PsTh
d2DE
cN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No threshold of triggering the inter-frequency


measurement for PS non-HSPA services. When Ec/No is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2D if the measured
Ec/No value is lower than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to start the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the easier it
will be to start the compressed mode. The smaller the value of
this parameter, the more difficult it is to stop the compressed
mode. To reduce the probability of frequently starting and
stopping the compressed mode, increase the difference between
the event 2D threshold and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterF
reqR9
9PsTh
d2DE
cN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: Ec/No threshold of triggering the inter-frequency


measurement for PS non-HSPA services. When Ec/No is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2D if the measured
Ec/No value is lower than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to start the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the easier it
will be to start the compressed mode. The smaller the value of
this parameter, the more difficult it is to stop the compressed

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
REQ
HOC
OV

Description

ed
on
Cov
erag
e

mode. To reduce the probability of frequently starting and


stopping the compressed mode, increase the difference between
the event 2D threshold and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterF
reqHT
hd2D
EcN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No threshold of triggering the inter-frequency


measurement for HSPA services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2D if the measured Ec/No value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterF
reqHT
hd2D
EcN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: Ec/No threshold of triggering the inter-frequency


measurement for HSPA services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2D if the measured Ec/No value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it is to stop the compressed mode. To reduce the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
REQ
HOC
OV

Description

ed
on
Cov
erag
e

probability of frequently starting and stopping the compressed


mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterF
reqR9
9PsTh
d2DR
SCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of triggering the inter-frequency


measurement for PS non-HSPA services. When RSCP is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2D if the measured
RSCP value is lower than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to start the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the easier it
will be to start the compressed mode. The smaller the value of
this parameter, the more difficult it is to stop the compressed
mode. To reduce the probability of frequently starting and
stopping the compressed mode, increase the difference between
the event 2D threshold and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

InterF
reqR9
9PsTh
d2DR
SCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: RSCP threshold of triggering the inter-frequency


measurement for PS non-HSPA services. When RSCP is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2D if the measured
RSCP value is lower than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to start the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the easier it
will be to start the compressed mode. The smaller the value of
this parameter, the more difficult it is to stop the compressed

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
REQ
HOC
OV

Description

ed
on
Cov
erag
e

mode. To reduce the probability of frequently starting and


stopping the compressed mode, increase the difference between
the event 2D threshold and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

InterF
reqHT
hd2D
RSCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of triggering the inter-frequency


measurement for HSPA services. When RSCP is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2D if the measured RSCP value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

InterF
reqHT
hd2D
RSCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: RSCP threshold of triggering the inter-frequency


measurement for HSPA services. When RSCP is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2D if the measured RSCP value is
lower than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to start the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the easier it will be to start the
compressed mode. The smaller the value of this parameter, the
more difficult it is to stop the compressed mode. To reduce the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
REQ
HOC
OV

Description

ed
on
Cov
erag
e

probability of frequently starting and stopping the compressed


mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

TrigTi B ADD
me2D S UCE
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 2D.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D320

TrigTi B ADD
me2D S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 2D.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D320

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Hystfo B ADD
r2D
S UCE
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis for event 2D. The hysteresis can be


evaluated based on the Ec/N0 or RSCP. For details about this
parameter, see 3GPP TS 25.331.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

Hystfo B ADD
r2D
S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis for event 2D. The hysteresis can be


evaluated based on the Ec/N0 or RSCP. For details about this
parameter, see 3GPP TS 25.331.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

InterR
ATCS
Thd2
DEcN
0

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed

Meaning: Threshold of triggering inter-RAT measurements for


CS services when Ec/N0 is used as the measurement quantity. If
the measured Ec/N0 value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

LLIN
TERR
ATH
OCO
V

on
Cov
erag
e

frequent enabling and disabling of the compressed mode,


increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterR
ATCS
Thd2
DEcN
0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurements for


CS services when Ec/N0 is used as the measurement quantity. If
the measured Ec/N0 value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

InterR
ATR9
9PsTh
d2DE
cN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurement for PS


domain non-HSPA services when Ec/N0 is used as the
measurement quantity. If the measured Ec/N0 value is lower than
this threshold, the UE reports event 2D. Then, the RNC sends the
signaling to enable the compressed mode and start inter-RAT
measurements. Event 2D and event 2F are used to enable and
disable the compressed mode respectively. To enable the
compressed mode earlier, increase the threshold of triggering
event 2D; otherwise, decrease the threshold of triggering event
2D. To prevent the frequent enabling and disabling of the
compressed mode, increase the difference between the thresholds
of triggering event 2D and event 2F.
GUI Value Range: -24~0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
V

Description

Unit: dB
Actual Value Range: -24~0
Default Value: -15

InterR
ATR9
9PsTh
d2DE
cN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurement for PS


domain non-HSPA services when Ec/N0 is used as the
measurement quantity. If the measured Ec/N0 value is lower than
this threshold, the UE reports event 2D. Then, the RNC sends the
signaling to enable the compressed mode and start inter-RAT
measurements. Event 2D and event 2F are used to enable and
disable the compressed mode respectively. To enable the
compressed mode earlier, increase the threshold of triggering
event 2D; otherwise, decrease the threshold of triggering event
2D. To prevent the frequent enabling and disabling of the
compressed mode, increase the difference between the thresholds
of triggering event 2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -15

InterR
ATHT
hd2D
EcN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurements for


HSPA services when Ec/N0 is used as the measurement quantity.
If the measured Ec/N0 value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -15

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

InterR
ATHT
hd2D
EcN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurements for


HSPA services when Ec/N0 is used as the measurement quantity.
If the measured Ec/N0 value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -15

InterR
ATR9
9PsTh
d2DR
SCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering inter-RAT measurement for PS


domain non-HSPA services when RSCP is used as the
measurement quantity. If the measured RSCP value is lower than
this threshold, the UE reports event 2D. Then, the RNC sends the
signaling to enable the compressed mode and start inter-RAT
measurements. Event 2D and event 2F are used to enable and
disable the compressed mode respectively. To enable the
compressed mode earlier, increase the threshold of triggering
event 2D; otherwise, decrease the threshold of triggering event
2D. To prevent the frequent enabling and disabling of the
compressed mode, increase the difference between the thresholds
of triggering event 2D and event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -110

InterR
ATR9
9PsTh
d2DR

B
S
C
6

ADD
UCE
LLIN
TERR

W
RF
D02

Inte
rRA
T

Meaning: Threshold of triggering inter-RAT measurement for PS


domain non-HSPA services when RSCP is used as the
measurement quantity. If the measured RSCP value is lower than
this threshold, the UE reports event 2D. Then, the RNC sends the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

SCP

9 ATH 03 Han signaling to enable the compressed mode and start inter-RAT
1 OCO 03 dov measurements. Event 2D and event 2F are used to enable and
0 V
er
disable the compressed mode respectively. To enable the
Bas
compressed mode earlier, increase the threshold of triggering
MOD
ed event 2D; otherwise, decrease the threshold of triggering event
UCE
on 2D. To prevent the frequent enabling and disabling of the
LLIN
Cov compressed mode, increase the difference between the thresholds
TERR
erag of triggering event 2D and event 2F.
ATH
e
OCO
GUI Value Range: -115~-25
V
Unit: dBm
Actual Value Range: -115~-25
Default Value: -110

InterR
ATHT
hd2D
RSCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of triggering measurements for HSPA


services when RSCP is used as the measurement quantity. If the
measured RSCP value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,
decrease the threshold of triggering event 2D. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -110

InterR
ATHT
hd2D
RSCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas

Meaning: Threshold of triggering measurements for HSPA


services when RSCP is used as the measurement quantity. If the
measured RSCP value is lower than this threshold, the UE
reports event 2D. Then, the RNC sends the signaling to enable
the compressed mode and start inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To enable the compressed mode earlier,
increase the threshold of triggering event 2D; otherwise,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UCE
LLIN
TERR
ATH
OCO
V

ed
on
Cov
erag
e

decrease the threshold of triggering event 2D. To prevent the


frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -110

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/N0 threshold for a UE to start an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed. If the measured Ec/N0 value is lower than this
threshold, the UE reports an event 2D report, and the RNC sends
signaling to instruct the UE to enable the compressed mode and
to start an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,
increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

CSPS
MRA
BThd
2DEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

CSPS
MRA
BThd
2DEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/N0 threshold for a UE to start an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed. If the measured Ec/N0 value is lower than this
threshold, the UE reports an event 2D report, and the RNC sends
signaling to instruct the UE to enable the compressed mode and
to start an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,
increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -14

CSPS
MRA
BThd
2DRS
CP

B
S
C
6
9
0
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE

W
RF
D02
03
02
W
RF
D-

Inte
r
Fre
que
ncy
Har
d
Han
dov

Meaning: RSCP threshold for a UE to start an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed. If the measured RSCP value is lower than this
threshold, the UE reports an event 2D report, and the RNC sends
signaling to instruct the UE to enable the compressed mode and
to start an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

LLM
ULTI
RAB
HOC
OV

02 er
03 Bas
03 ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

frequent enabling and disabling of the compressed mode,


increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Meaning: RSCP threshold for a UE to start an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed. If the measured RSCP value is lower than this
threshold, the UE reports an event 2D report, and the RNC sends
signaling to instruct the UE to enable the compressed mode and
to start an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,
increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -95

CSPS
MRA
BThd
2DRS
CP

B
S
C
6
9
1
0

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r-

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
TimeT B ADD
oTrig2 S UCE
F
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 2F. A UE reports an event


2F measurement report if the conditions for triggering event 2F
are met and persist during the time period specified by this
parameter.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D1280

TimeT B ADD
oTrig2 S UCE
F
C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Time delay to trigger event 2F. A UE reports an event


2F measurement report if the conditions for triggering event 2F
are met and persist during the time period specified by this
parameter.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D1280

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
TERF
REQ
HOC
OV

Description

Bas
ed
on
Cov
erag
e

HystF B ADD
or2F S UCE
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis for triggering event 2F. When


"InterFreqReportMode" is set to PERIODICAL_REPORTING,
the hysteresis in active set quality measurement is used to
prevent the ping-pong reporting of event 2D (triggered when the
estimated quality of the frequency in use is lower than the
threshold) and event 2F (triggered when the estimated quality of
the frequency in use is higher than the threshold). Event 2D is
used to enable the compression mode and event 2F is used to
disable the compression mode.To prevent the compression mode
from being frequently enabled and disabled, you can set
"Hystfor2D" and "Hystfor2F" to be greater than their
recommended values according to the statistics of the ping-pong
inter-frequency handover.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

HystF B ADD
or2F S UCE
C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: Hysteresis for triggering event 2F. When


"InterFreqReportMode" is set to PERIODICAL_REPORTING,
the hysteresis in active set quality measurement is used to
prevent the ping-pong reporting of event 2D (triggered when the
estimated quality of the frequency in use is lower than the
threshold) and event 2F (triggered when the estimated quality of
the frequency in use is higher than the threshold). Event 2D is
used to enable the compression mode and event 2F is used to
disable the compression mode.To prevent the compression mode
from being frequently enabled and disabled, you can set
"Hystfor2D" and "Hystfor2F" to be greater than their
recommended values according to the statistics of the ping-pong
inter-frequency handover.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: 0~29


e
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4
InterF
reqCS
Thd2F
EcN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No threshold of stopping the inter-frequency


measurement for CS services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2F if the measured Ec/No value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

InterF
reqCS
Thd2F
EcN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: Ec/No threshold of stopping the inter-frequency


measurement for CS services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2F if the measured Ec/No value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: -24~0


e
Unit: dB
Actual Value Range: -24~0
Default Value: -12
InterF
reqR9
9PsTh
d2FEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No threshold of stopping the inter-frequency


measurement for PS non-HSPA services. When Ec/No is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2F if the measured
Ec/No value is higher than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to stop the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the more
difficult it is to stop the compressed mode. The smaller the value
of this parameter, the easier it is to stop the compressed mode. To
reduce the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

InterF
reqR9
9PsTh
d2FEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: Ec/No threshold of stopping the inter-frequency


measurement for PS non-HSPA services. When Ec/No is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2F if the measured
Ec/No value is higher than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to stop the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the more
difficult it is to stop the compressed mode. The smaller the value
of this parameter, the easier it is to stop the compressed mode. To
reduce the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: -24~0


e
Unit: dB
Actual Value Range: -24~0
Default Value: -12
InterF
reqHT
hd2FE
cN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No threshold of stopping the inter-frequency


measurement for HSPA services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2F if the measured Ec/No value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

InterF
reqHT
hd2FE
cN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: Ec/No threshold of stopping the inter-frequency


measurement for HSPA services. When Ec/No is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2F if the measured Ec/No value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: -24~0


e
Unit: dB
Actual Value Range: -24~0
Default Value: -12
InterF
reqCS
Thd2F
RSCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of stopping the inter-frequency


measurement for CS services. When RSCP is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2F if the measured RSCP value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

InterF
reqCS
Thd2F
RSCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: RSCP threshold of stopping the inter-frequency


measurement for CS services. When RSCP is used as the
measurement quantity for inter-frequency handovers of CS
services, the UE reports event 2F if the measured RSCP value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: -115~-25


e
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92
InterF
reqR9
9PsTh
d2FR
SCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of stopping the inter-frequency


measurement for PS non-HSPA services. When RSCP is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2F if the measured
RSCP value is higher than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to stop the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the more
difficult it is to stop the compressed mode. The smaller the value
of this parameter, the easier it is to stop the compressed mode. To
reduce the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

InterF
reqR9
9PsTh
d2FR
SCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: RSCP threshold of stopping the inter-frequency


measurement for PS non-HSPA services. When RSCP is used as
the measurement quantity for inter-frequency handovers of PS
non-HSPA services, the UE reports event 2F if the measured
RSCP value is higher than the value of this parameter. Then, the
RNC sends a signaling message to instruct the UE to stop the
compressed mode and the inter-frequency measurement. Events
2D and 2F are used to start and stop the compressed mode,
respectively. The larger the value of this parameter, the more
difficult it is to stop the compressed mode. The smaller the value
of this parameter, the easier it is to stop the compressed mode. To
reduce the probability of frequently starting and stopping the
compressed mode, increase the difference between the event 2D
threshold and event 2F threshold.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: -115~-25


e
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92
InterF
reqHT
hd2FR
SCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold of stopping the inter-frequency


measurement for HSPA services. When RSCP is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2F if the measured RSCP value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

InterF
reqHT
hd2FR
SCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: RSCP threshold of stopping the inter-frequency


measurement for HSPA services. When RSCP is used as the
measurement quantity for inter-frequency handovers of HSPA
services, the UE reports event 2F if the measured RSCP value is
higher than the value of this parameter. Then, the RNC sends a
signaling message to instruct the UE to stop the compressed
mode and the inter-frequency measurement. Events 2D and 2F
are used to start and stop the compressed mode, respectively. The
larger the value of this parameter, the more difficult it is to stop
the compressed mode. The smaller the value of this parameter,
the easier it is to stop the compressed mode. To reduce the
probability of frequently starting and stopping the compressed
mode, increase the difference between the event 2D threshold
and event 2F threshold.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag GUI Value Range: -115~-25


e
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92
TrigTi B ADD
me2F S UCE
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 2F.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D1280

TrigTi B ADD
me2F S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 2F.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D1280

Hystfo B ADD
r2F
S UCE
C LLIN
6 TERR

W
RF
D02

Inte Meaning: Hysteresis for event 2F. The hysteresis can be


revaluated based on the Ec/N0 or RSCP. For details about this
RA parameter, see 3GPP TS 25.331.
T

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

9 ATH 03 Han GUI Value Range: 0~29


0 OCO 03 dov Unit: 0.5dB; 0.5dBm
0 V
er
Actual Value Range: 0~14.5
Bas
MOD
Default Value: 4
ed
UCE
on
LLIN
Cov
TERR
erag
ATH
e
OCO
V
Hystfo B ADD
r2F
S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis for event 2F. The hysteresis can be


evaluated based on the Ec/N0 or RSCP. For details about this
parameter, see 3GPP TS 25.331.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

InterR
ATCS
Thd2F
EcN0

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurements for CS


services when Ec/N0 is used as the measurement quantity. If the
measured Ec/N0 value is greater than this threshold, the UE
reports event 2F. Then, the RNC sends the signaling to disable
the compressed mode and stop inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To disable the compressed mode earlier,
reduce the threshold of triggering event 2F; otherwise, increase
the threshold of triggering event 2F. To prevent the frequent
enabling and disabling of the compressed mode, increase the
difference between the thresholds of triggering event 2D and
event 2F.
GUI Value Range: -24~0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
V

Description

Unit: dB
Actual Value Range: -24~0
Default Value: -12

InterR
ATCS
Thd2F
EcN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurements for CS


services when Ec/N0 is used as the measurement quantity. If the
measured Ec/N0 value is greater than this threshold, the UE
reports event 2F. Then, the RNC sends the signaling to disable
the compressed mode and stop inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To disable the compressed mode earlier,
reduce the threshold of triggering event 2F; otherwise, increase
the threshold of triggering event 2F. To prevent the frequent
enabling and disabling of the compressed mode, increase the
difference between the thresholds of triggering event 2D and
event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

InterR
ATR9
9PsTh
d2FEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurement for PS


domain non-HSPA services when Ec/N0 is used as the
measurement quantity. If the measured Ec/N0 value is greater
than this threshold, the UE reports event 2F. Then, the RNC
sends the signaling to disable the compressed mode and stop
inter-RAT measurements. Event 2D and event 2F are used to
enable and disable the compressed mode respectively. To disable
the compressed mode earlier, reduce the threshold of triggering
event 2F; otherwise, increase the threshold of triggering event
2F. To prevent the frequent enabling and disabling of the
compressed mode, increase the difference between the thresholds
of triggering event 2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -13

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

InterR
ATR9
9PsTh
d2FEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurement for PS


domain non-HSPA services when Ec/N0 is used as the
measurement quantity. If the measured Ec/N0 value is greater
than this threshold, the UE reports event 2F. Then, the RNC
sends the signaling to disable the compressed mode and stop
inter-RAT measurements. Event 2D and event 2F are used to
enable and disable the compressed mode respectively. To disable
the compressed mode earlier, reduce the threshold of triggering
event 2F; otherwise, increase the threshold of triggering event
2F. To prevent the frequent enabling and disabling of the
compressed mode, increase the difference between the thresholds
of triggering event 2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -13

InterR
ATHT
hd2FE
cN0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurements for


HSPA services when Ec/N0 is used as the measurement quantity.
If the measured Ec/N0 value is greater than this threshold, the
UE reports event 2F. Then, the RNC sends the signaling to
disable the compressed mode and stop inter-RAT measurements.
Event 2D and event 2F are used to enable and disable the
compressed mode respectively. To disable the compressed mode
earlier, reduce the threshold of triggering event 2F; otherwise,
increase the threshold of triggering event 2F. To prevent the
frequent enabling and disabling of the compressed mode,
increase the difference between the thresholds of triggering event
2D and event 2F.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -13

InterR
ATHT
hd2FE
cN0

B
S
C
6

ADD
UCE
LLIN
TERR

W
RF
D02

Inte
rRA
T

Meaning: Threshold of stopping inter-RAT measurements for


HSPA services when Ec/N0 is used as the measurement quantity.
If the measured Ec/N0 value is greater than this threshold, the
UE reports event 2F. Then, the RNC sends the signaling to

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

9 ATH 03 Han disable the compressed mode and stop inter-RAT measurements.
1 OCO 03 dov Event 2D and event 2F are used to enable and disable the
0 V
er
compressed mode respectively. To disable the compressed mode
Bas
earlier, reduce the threshold of triggering event 2F; otherwise,
MOD
ed increase the threshold of triggering event 2F. To prevent the
UCE
on frequent enabling and disabling of the compressed mode,
LLIN
Cov increase the difference between the thresholds of triggering event
TERR
erag 2D and event 2F.
ATH
e
OCO
GUI Value Range: -24~0
V
Unit: dB
Actual Value Range: -24~0
Default Value: -13
InterR
ATCS
Thd2F
RSCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurements for CS


services when RSCP is used as the measurement quantity. If the
measured RSCP value is greater than this threshold, the UE
reports event 2F. Then, the RNC sends the signaling to disable
the compressed mode and stop inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To disable the compressed mode earlier,
reduce the threshold of triggering event 2F; otherwise, increase
the threshold of triggering event 2F. To prevent the frequent
enabling and disabling of the compressed mode, increase the
difference between the thresholds of triggering event 2D and
event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -97

InterR
ATCS
Thd2F
RSCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas

Meaning: Threshold of stopping inter-RAT measurements for CS


services when RSCP is used as the measurement quantity. If the
measured RSCP value is greater than this threshold, the UE
reports event 2F. Then, the RNC sends the signaling to disable
the compressed mode and stop inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To disable the compressed mode earlier,
reduce the threshold of triggering event 2F; otherwise, increase

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UCE
LLIN
TERR
ATH
OCO
V

Description

ed
on
Cov
erag
e

the threshold of triggering event 2F. To prevent the frequent


enabling and disabling of the compressed mode, increase the
difference between the thresholds of triggering event 2D and
event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -97

InterR
ATR9
9PsTh
d2FR
SCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurement when


RSCP is used as the measurement quantity. If the measured
RSCP value is greater than this threshold, the UE reports event
2F. Then, the RNC sends the signaling to disable the compressed
mode and stop inter-RAT measurements. Event 2D and event 2F
are used to enable and disable the compressed mode respectively.
To disable the compressed mode earlier, reduce the threshold of
triggering event 2F; otherwise, increase the threshold of
triggering event 2F. To prevent the frequent enabling and
disabling of the compressed mode, increase the difference
between the thresholds of triggering event 2D and event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -107

InterR
ATR9
9PsTh
d2FR
SCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping inter-RAT measurement when


RSCP is used as the measurement quantity. If the measured
RSCP value is greater than this threshold, the UE reports event
2F. Then, the RNC sends the signaling to disable the compressed
mode and stop inter-RAT measurements. Event 2D and event 2F
are used to enable and disable the compressed mode respectively.
To disable the compressed mode earlier, reduce the threshold of
triggering event 2F; otherwise, increase the threshold of
triggering event 2F. To prevent the frequent enabling and
disabling of the compressed mode, increase the difference
between the thresholds of triggering event 2D and event 2F.
GUI Value Range: -115~-25
Unit: dBm

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
V

Description

Actual Value Range: -115~-25


Default Value: -107

InterR
ATHT
hd2FR
SCP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping measurements for HSPA


services when RSCP is used as the measurement quantity. If the
measured RSCP value is greater than this threshold, the UE
reports event 2F. Then, the RNC sends the signaling to disable
the compressed mode and stop inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To disable the compressed mode earlier,
reduce the threshold of triggering event 2F; otherwise, increase
the threshold of triggering event 2F. To prevent the frequent
enabling and disabling of the compressed mode, increase the
difference between the thresholds of triggering event 2D and
event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -107

InterR
ATHT
hd2FR
SCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of stopping measurements for HSPA


services when RSCP is used as the measurement quantity. If the
measured RSCP value is greater than this threshold, the UE
reports event 2F. Then, the RNC sends the signaling to disable
the compressed mode and stop inter-RAT measurements. Event
2D and event 2F are used to enable and disable the compressed
mode respectively. To disable the compressed mode earlier,
reduce the threshold of triggering event 2F; otherwise, increase
the threshold of triggering event 2F. To prevent the frequent
enabling and disabling of the compressed mode, increase the
difference between the thresholds of triggering event 2D and
event 2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -107

CSPS

B ADD

W Inte Meaning: Ec/N0 threshold for a UE to stop an inter-frequency or

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

MRA
BThd
2FEc
N0

S
C
6
9
0
0

UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

RF
D02
03
02
W
RF
D02
03
03

r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

inter-RAT measurement when CS and PS combined services are


processed If the measured Ec/N0 value is higher than this
threshold, the UE reports an event 2F report, and the RNC sends
signaling to instruct the UE to disable the compressed mode and
to stop an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,
increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

CSPS
MRA
BThd
2FEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM

W
RF
D02
03
02
W
RF
D02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Ec/N0 threshold for a UE to stop an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed If the measured Ec/N0 value is higher than this
threshold, the UE reports an event 2F report, and the RNC sends
signaling to instruct the UE to disable the compressed mode and
to stop an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

CSPS
MRA
BThd
2FRS
CP

B
S
C
6
9
0
0

Description

ULTI
RAB
HOC
OV

03 Bas increase the difference between the event 2D threshold and event
03 ed 2F threshold.
on GUI Value Range: -24~0
Cov Unit: dB
erag
Actual Value Range: -24~0
e
Default Value: -12
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA

Meaning: RSCP threshold for a UE to stop an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed. If the measured RSCP value is higher than this
threshold, the UE reports an event 2F report, and the RNC sends
signaling to instruct the UE to disable the compressed mode and
to stop an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,
increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

T
Han
dov
er
Bas
ed
on
Cov
erag
e
CSPS
MRA
BThd
2FRS
CP

B
S
C
6
9
1
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag

Meaning: RSCP threshold for a UE to stop an inter-frequency or


inter-RAT measurement when CS and PS combined services are
processed. If the measured RSCP value is higher than this
threshold, the UE reports an event 2F report, and the RNC sends
signaling to instruct the UE to disable the compressed mode and
to stop an inter-frequency or inter-RAT measurement. Events 2D
and 2F are used to enable and disable the compressed mode,
respectively. To enable the compressed mode earlier, set the
event 2D threshold to a large value. To reduce the probability of
frequent enabling and disabling of the compressed mode,
increase the difference between the event 2D threshold and event
2F threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

e
TimeT B ADD
oTrig2 S UCE
B
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: Time delay to trigger event 2B. A UE reports an event


2B measurement report if the conditions for triggering event 2B
are met and persist during the time period specified by this
parameter.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D0

TimeT B ADD
oTrig2 S UCE
B
C LLIN
6 TERF

W
RF
D02

Inte
r
Fre
que

Meaning: Time delay to trigger event 2B. A UE reports an event


2B measurement report if the conditions for triggering event 2B
are met and persist during the time period specified by this
parameter.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

03
02
W
RF
D02
03
04

ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D0

HystF B ADD
or2B S UCE
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Event 2B hysteresis. The hysteresis can be the Ec/No


or RSCP. For details, see 3GPP TS 25.331.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
TERF
REQ
HOC
OV

Description

Bas
ed
on
Cov
erag
e

HystF B ADD
or2B S UCE
C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Event 2B hysteresis. The hysteresis can be the Ec/No


or RSCP. For details, see 3GPP TS 25.331.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 4

Target
FreqC
sThdE
cN0

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
Ec/No for CS services. For CS services, if the inter-frequency
reporting mode is set to "EVENT_TRIGGER", this parameter is
used to set the criterion for triggering event 2B. That is, event 2B
can be triggered when the quality of the target frequency is
higher than this threshold. If the inter-frequency reporting mode
is set to "PERIODIC_TRIGGER", this parameter is used for
handover decision.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

e
Target
FreqC
sThdE
cN0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
Ec/No for CS services. For CS services, if the inter-frequency
reporting mode is set to "EVENT_TRIGGER", this parameter is
used to set the criterion for triggering event 2B. That is, event 2B
can be triggered when the quality of the target frequency is
higher than this threshold. If the inter-frequency reporting mode
is set to "PERIODIC_TRIGGER", this parameter is used for
handover decision.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Target
FreqC
sThdR
scp

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
RSCP for CS services. For CS services, if the inter-frequency
reporting mode is set to "EVENT_TRIGGER", this parameter is
used to set the criterion for triggering event 2B. That is, event 2B
can be triggered when the quality of the target frequency is
higher than this threshold. If the inter-frequency reporting mode
is set to "PERIODIC_TRIGGER", this parameter is used for
handover decision.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Target B ADD W Inte Meaning: Threshold of the target frequency for triggering interFreqC S UCE RF r
frequency measurement based on measurement quantity of
sThdR C LLIN D- Fre RSCP for CS services. For CS services, if the inter-frequency

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

scp

6
9
1
0

TERF 02 que reporting mode is set to "EVENT_TRIGGER", this parameter is


REQ 03 ncy used to set the criterion for triggering event 2B. That is, event 2B
HOC 02 Har can be triggered when the quality of the target frequency is
OV
d
higher than this threshold. If the inter-frequency reporting mode
Han is set to "PERIODIC_TRIGGER", this parameter is used for
MOD
dov handover decision.
UCE
er
LLIN
GUI Value Range: -115~-25
Bas
TERF
Unit: dBm
ed
REQ
Actual Value Range: -115~-25
on
HOC
Cov Default Value: -92
OV
erag
e

Target
FreqR
99PsT
hdEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
Ec/No for non-HSPA services in PS domain.For non-HSPA
services in PS domain, if the inter-frequency reporting mode is
set to "EVENT_TRIGGER", this parameter is used to set the
criterion for triggering event 2B. That is, event 2B can be
triggered when the quality of the target frequency is higher than
this threshold. If the inter-frequency reporting mode is set to
"PERIODIC_TRIGGER", this parameter is used for handover
decision.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Target
FreqR
99PsT
hdEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
Ec/No for non-HSPA services in PS domain.For non-HSPA
services in PS domain, if the inter-frequency reporting mode is
set to "EVENT_TRIGGER", this parameter is used to set the
criterion for triggering event 2B. That is, event 2B can be
triggered when the quality of the target frequency is higher than
this threshold. If the inter-frequency reporting mode is set to

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UCE
LLIN
TERF
REQ
HOC
OV

Description

dov
er
Bas
ed
on
Cov
erag
e

"PERIODIC_TRIGGER", this parameter is used for handover


decision.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Target
FreqR
99PsT
hdRsc
p

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
RSCP for non-HSPA services in PS domain.For non-HSPA
services in PS domain, if the inter-frequency reporting mode is
set to "EVENT_TRIGGER", this parameter is used to set the
criterion for triggering event 2B. That is, event 2B can be
triggered when the quality of the target frequency is higher than
this threshold. If the inter-frequency reporting mode is set to
"PERIODIC_TRIGGER", this parameter is used for handover
decision.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Target
FreqR
99PsT
hdRsc
p

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
RSCP for non-HSPA services in PS domain.For non-HSPA
services in PS domain, if the inter-frequency reporting mode is
set to "EVENT_TRIGGER", this parameter is used to set the
criterion for triggering event 2B. That is, event 2B can be
triggered when the quality of the target frequency is higher than
this threshold. If the inter-frequency reporting mode is set to
"PERIODIC_TRIGGER", this parameter is used for handover
decision.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
OV

Description

Cov Default Value: -92


erag
e

Target
FreqH
ThdEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
Ec/No for HSPA services.For HSPA services, if the interfrequency reporting mode is set to "EVENT_TRIGGER", this
parameter is used to set the criterion for triggering event 2B.
That is, event 2B can be triggered when the quality of the target
frequency is higher than this threshold. If the inter-frequency
reporting mode is set to "PERIODIC_TRIGGER", this parameter
is used for handover decision.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Target
FreqH
ThdEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
Ec/No for HSPA services.For HSPA services, if the interfrequency reporting mode is set to "EVENT_TRIGGER", this
parameter is used to set the criterion for triggering event 2B.
That is, event 2B can be triggered when the quality of the target
frequency is higher than this threshold. If the inter-frequency
reporting mode is set to "PERIODIC_TRIGGER", this parameter
is used for handover decision.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Target B ADD

W Inte Meaning: Threshold of the target frequency for triggering inter-

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

FreqH S UCE RF
ThdRs C LLIN Dcp
6 TERF 02
9 REQ 03
0 HOC 02
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

frequency measurement based on measurement quantity of


RSCP for HSPA services. For HSPA services, if the interfrequency reporting mode is set to "EVENT_TRIGGER", this
parameter is used to set the criterion for triggering event 2B.
That is, event 2B can be triggered when the quality of the target
frequency is higher than this threshold. If the inter-frequency
reporting mode is set to "PERIODIC_TRIGGER", this parameter
is used for handover decision. After handover, to prevent pingpong handover, the inter-frequency measurement should not be
started again. That is, this parameter is usually set greater than
the start threshold for event 2D or equal to the threshold of event
2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Target
FreqH
ThdRs
cp

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of the target frequency for triggering interfrequency measurement based on measurement quantity of
RSCP for HSPA services. For HSPA services, if the interfrequency reporting mode is set to "EVENT_TRIGGER", this
parameter is used to set the criterion for triggering event 2B.
That is, event 2B can be triggered when the quality of the target
frequency is higher than this threshold. If the inter-frequency
reporting mode is set to "PERIODIC_TRIGGER", this parameter
is used for handover decision. After handover, to prevent pingpong handover, the inter-frequency measurement should not be
started again. That is, this parameter is usually set greater than
the start threshold for event 2D or equal to the threshold of event
2F.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

UsedF B ADD W Inte Meaning: Threshold of used frequency quality for triggering
reqCS S UCE RF r
RSCP-based measurement for CS services. When RSCP is used
ThdR C LLIN D- Fre as the measurement quantity for CS services, one of the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

SCP

6
9
0
0

TERF 02 que necessary conditions for triggering event 2B can be met only
REQ 03 ncy when the quality of the used frequency is lower than the value of
HOC 02 Har this parameter. Event 2B is triggered only when both the
OV
d
necessary conditions are met.
Han GUI Value Range: -115~-25
MOD
dov Unit: dBm
UCE
er
LLIN
Actual Value Range: -115~-25
Bas
TERF
ed Default Value: -92
REQ
on
HOC
Cov
OV
erag
e

UsedF
reqCS
ThdR
SCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of used frequency quality for triggering


RSCP-based measurement for CS services. When RSCP is used
as the measurement quantity for CS services, one of the
necessary conditions for triggering event 2B can be met only
when the quality of the used frequency is lower than the value of
this parameter. Event 2B is triggered only when both the
necessary conditions are met.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

UsedF
reqR9
9PsTh
dRSC
P

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han

Meaning: Threshold of used frequency quality for triggering


RSCP-based measurement for PS non-HSPA services. When
RSCP is used as the measurement quantity for PS non-HSPA
services, one of the necessary conditions for triggering event 2B
can be met only when the quality of the used frequency is lower
than the value of this parameter. Event 2B is triggered only when
both the necessary conditions are met.
GUI Value Range: -115~-25

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UCE
LLIN
TERF
REQ
HOC
OV

Description

dov Unit: dBm


er
Actual Value Range: -115~-25
Bas Default Value: -92
ed
on
Cov
erag
e

UsedF
reqR9
9PsTh
dRSC
P

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of used frequency quality for triggering


RSCP-based measurement for PS non-HSPA services. When
RSCP is used as the measurement quantity for PS non-HSPA
services, one of the necessary conditions for triggering event 2B
can be met only when the quality of the used frequency is lower
than the value of this parameter. Event 2B is triggered only when
both the necessary conditions are met.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

UsedF
reqHT
hdRS
CP

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Meaning: The larger the value of this parameter, the more


difficult it will be to trigger event 2B and inter-frequency
handovers, and the more easily call drops occur due to delayed
handovers. The smaller the value of this parameter, the easier it
will be to trigger event 2B. If this parameter is set to a very small
value, the handover success rate decreases. In most cases, this
value of this parameter should be smaller than the threshold for
triggering event 2F or should be equal to the threshold for
triggering event 2D.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
OV

Description

Cov
erag
e

UsedF
reqHT
hdRS
CP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: The larger the value of this parameter, the more


difficult it will be to trigger event 2B and inter-frequency
handovers, and the more easily call drops occur due to delayed
handovers. The smaller the value of this parameter, the easier it
will be to trigger event 2B. If this parameter is set to a very small
value, the handover success rate decreases. In most cases, this
value of this parameter should be smaller than the threshold for
triggering event 2F or should be equal to the threshold for
triggering event 2D.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

UsedF
reqCS
ThdEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of used frequency quality for triggering


Ec/No-based measurement for CS services. When Ec/No is used
as the measurement quantity for CS services, one of the
necessary conditions for triggering event 2B can be met only
when the quality of the used frequency is lower than the value of
this parameter. Event 2B is triggered only when both the
necessary conditions are met.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

UsedF B ADD

W Inte Meaning: Threshold of used frequency quality for triggering

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

reqCS S UCE RF
ThdEc C LLIN DN0
6 TERF 02
9 REQ 03
1 HOC 02
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Ec/No-based measurement for CS services. When Ec/No is used


as the measurement quantity for CS services, one of the
necessary conditions for triggering event 2B can be met only
when the quality of the used frequency is lower than the value of
this parameter. Event 2B is triggered only when both the
necessary conditions are met.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

UsedF
reqR9
9PsTh
dEcN
0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of used frequency quality for triggering


Ec/No-based measurement for PS non-HSPA services. When
Ec/No is used as the measurement quantity for PS non-HSPA
services, one of the necessary conditions for triggering event 2B
can be met only when the quality of the used frequency is lower
than the value of this parameter. Event 2B is triggered only when
both the necessary conditions are met.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

UsedF
reqR9
9PsTh
dEcN
0

B
S
C
6
9
1

ADD
UCE
LLIN
TERF
REQ
HOC

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har

Meaning: Threshold of used frequency quality for triggering


Ec/No-based measurement for PS non-HSPA services. When
Ec/No is used as the measurement quantity for PS non-HSPA
services, one of the necessary conditions for triggering event 2B
can be met only when the quality of the used frequency is lower
than the value of this parameter. Event 2B is triggered only when

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

Description

d
Han
dov
er
Bas
ed
on
Cov
erag
e

both the necessary conditions are met.


GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

UsedF
reqHT
hdEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Threshold of used frequency quality for triggering


Ec/No-based measurement for HSPA services. When Ec/No is
used as the measurement quantity for HSPA services, one of the
necessary conditions for triggering event 2B can be met only
when the quality of the used frequency is lower than the value of
this parameter. Event 2B is triggered only when both the
necessary conditions are met.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

UsedF
reqHT
hdEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas

Meaning: Threshold of used frequency quality for triggering


Ec/No-based measurement for HSPA services. When Ec/No is
used as the measurement quantity for HSPA services, one of the
necessary conditions for triggering event 2B can be met only
when the quality of the used frequency is lower than the value of
this parameter. Event 2B is triggered only when both the
necessary conditions are met.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
REQ
HOC
OV

Target
FreqC
SPSM
RABT
hdEc
No

B
S
C
6
9
0
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

Target B ADD
FreqC S UCE
SPSM C LLM

Description

ed
on
Cov
erag
e
W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/N0 threshold for triggering a measurement-based


inter-frequency hard handover to a cell that operates at the target
frequency for CS and PS combined services Event 2B is reported
when both of the following conditions are met: -The eventtriggered reporting mode is used for inter-frequency
measurement, and signal quality in the cell that operates at the
target frequency is higher than this threshold. -The criterion for
UsedFreqCSPSThdEcN0 is fulfilled. If the periodic reporting
mode is used for inter-frequency measurement, the RNC makes a
handover decision based on this threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

W Inte Meaning: Ec/N0 threshold for triggering a measurement-based


RF r
inter-frequency hard handover to a cell that operates at the target
D- Fre frequency for CS and PS combined services Event 2B is reported

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RABT 6 ULTI
hdEc 9 RAB
No
1 HOC
0 OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

02
03
02
W
RF
D02
03
03

que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

when both of the following conditions are met: -The eventtriggered reporting mode is used for inter-frequency
measurement, and signal quality in the cell that operates at the
target frequency is higher than this threshold. -The criterion for
UsedFreqCSPSThdEcN0 is fulfilled. If the periodic reporting
mode is used for inter-frequency measurement, the RNC makes a
handover decision based on this threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

Target
FreqC
SPSM
RABT
hdRsc
p

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed

Meaning: RSCP threshold for triggering a measurement-based


inter-frequency hard handover to a cell that operates at the target
frequency for CS and PS combined services Event 2B is reported
when both of the following conditions are met: -The eventtriggered reporting mode is used for inter-frequency
measurement, and signal quality in the cell that operates in the
target frequency is higher than this threshold. -The criterion for
UsedFreqCSPSThdRSCP is fulfilled. If the periodic reporting
mode is used for inter-frequency measurement, the RNC makes a
handover decision based on this threshold.
GUI Value Range: -115~-25
Unit: dBm

B
S
C
6
9
0
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
HOC
OV

Target
FreqC
SPSM
RABT
hdRsc
p

B
S
C
6
9
1
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

Description

on Actual Value Range: -115~-25


Cov Default Value: -92
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han

Meaning: RSCP threshold for triggering a measurement-based


inter-frequency hard handover to a cell that operates at the target
frequency for CS and PS combined services Event 2B is reported
when both of the following conditions are met: -The eventtriggered reporting mode is used for inter-frequency
measurement, and signal quality in the cell that operates in the
target frequency is higher than this threshold. -The criterion for
UsedFreqCSPSThdRSCP is fulfilled. If the periodic reporting
mode is used for inter-frequency measurement, the RNC makes a
handover decision based on this threshold.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

dov
er
Bas
ed
on
Cov
erag
e
TrigTi B ADD
me3A S UCE
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 3A.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D0

TrigTi B ADD
me3A S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Time delay to trigger event 3A.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

DlRsc B ADD
pQos S UCE
Hyst C LLQ
6 OSH
9 O
0 MOD
0 UCE
LLQ
OSH
O

W
RF
D02
03
09
W
RF
D02
03
04

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: Frequency hysteresis of downlink RSCP QoS. This


parameter controls the used frequency thresholds for the interfrequency and inter-RAT measurement based on QoS. In event
mode, if the inter-frequency and inter-RAT measurement events
occurred for the downlink QoS reason, the used frequency
threshold of the RSCP measurement quantity is equal to the used
frequency threshold that is configured on the OMU server in
coverage measurement plus this parameter. As for the impact on
network performance: The larger the value of the parameter is,
the more easily event 2B, inter-frequency handover based on
QoS, and event 3A, inter-RAT handover based on QoS, can be
triggered, and thus the more timely the handover to the target
cell can be performed.
GUI Value Range: -15~15
Unit: dB
Actual Value Range: -15~15
Default Value: 10

DlRsc B ADD
pQos S UCE
Hyst C LLQ
6 OSH
9 O
1 MOD
0 UCE
LLQ
OSH

W
RF
D02
03
09
W
RF
D-

Inte
rRA
T
Han
dov
er
Bas
ed

Meaning: Frequency hysteresis of downlink RSCP QoS. This


parameter controls the used frequency thresholds for the interfrequency and inter-RAT measurement based on QoS. In event
mode, if the inter-frequency and inter-RAT measurement events
occurred for the downlink QoS reason, the used frequency
threshold of the RSCP measurement quantity is equal to the used
frequency threshold that is configured on the OMU server in
coverage measurement plus this parameter. As for the impact on
network performance: The larger the value of the parameter is,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
O

CIOO B ADD
ffset
S UINT
C ERFR
6 EQN
9 CELL
0 MOD
0 UINT
ERFR
EQN
CELL

Description

02 on
03 DL
04 Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

the more easily event 2B, inter-frequency handover based on


QoS, and event 3A, inter-RAT handover based on QoS, can be
triggered, and thus the more timely the handover to the target
cell can be performed.
GUI Value Range: -15~15
Unit: dB
Actual Value Range: -15~15
Default Value: 10

W
RF
D02
02
01

Meaning: CIO of a neighboring cell. This parameter works with


"CIO". The sum of "CIOOffset", "CIO", and the actual measured
value are used for UE event evaluation or decisions on
handovers triggered by the RNC. In a handover algorithm, this
parameter is used for moving the border of a cell. In the case of
an event-based intra-frequency measurement or inter-RAT
measurement, the UE determines whether to trigger an event
according to the sum of "CIOOffset", "CIO", and the actual
measured value. The UE does not consider the value of this
parameter when evaluating an inter-frequency measurement
event. In the case of a periodical inter-frequency measurement or
inter-RAT measurement, the RNC determines whether to initiate
a handover based on the sum of "CIOOffset", "CIO", and the
actual measured value.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10

Intr
a
Nod
eB
Soft
er
Han
dov
er

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Default Value: 0
CIOO B ADD
ffset
S UINT
C ERFR
6 EQN
9 CELL
1 MOD
0 UINT
ERFR
EQN
CELL

W
RF
D02
02
01

Intr
a
Nod
eB
Soft
er
Han
dov
er

Meaning: CIO of a neighboring cell. This parameter works with


"CIO". The sum of "CIOOffset", "CIO", and the actual measured
value are used for UE event evaluation or decisions on
handovers triggered by the RNC. In a handover algorithm, this
parameter is used for moving the border of a cell. In the case of
an event-based intra-frequency measurement or inter-RAT
measurement, the UE determines whether to trigger an event
according to the sum of "CIOOffset", "CIO", and the actual
measured value. The UE does not consider the value of this
parameter when evaluating an inter-frequency measurement
event. In the case of a periodical inter-frequency measurement or
inter-RAT measurement, the RNC determines whether to initiate
a handover based on the sum of "CIOOffset", "CIO", and the
actual measured value.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
Default Value: 0

Target B ADD
RatCs S UCE
Thd
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality requirement for the cell of another RAT during


inter-RAT CS handovers. For CS services, if "Inter-RAT
Reporting Mode" is set to EVENT_TRIGGER, this parameter is
used to set the criterion for triggering event 3A. That is, event 3A
can be triggered only when the quality of the target frequency is
higher than this threshold and the measurement quality of the
current CS services is lower than the quality of the currently
used frequency. If "Inter-RAT Reporting Mode" is set to
PERIODIC_TRIGGER, this parameter is used for inter-RAT
handover decisions on the RNC. Note that value 0 indicates the
value of this parameter is smaller than -110 dBm. If "Inter-RAT
Reporting Mode" is set to PERIODIC_TRIGGER, this
parameter is used for the assessment of coverage-based interRAT handovers. That is, Tother_RAT in the following formula.
This parameter is the absolute threshold of the cell of another
RAT (Received Signal Strength Indicator: RSSI) for the interRAT handover decisions. If the quality of the cell of another
RAT in the inter-RAT measurement report fulfills the following

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

criterion: Mother_RAT + CIO >= Tother_RAT + H/2 The system


starts the trigger timer, and makes the handover decision after the
timer expires. If the quality of the cell of another RAT fulfills the
following criterion before timeout: Mother_RAT + CIO <
Tother_RAT - H/2 The RNC stops the timer and waits for
another inter-RAT measurement report. Where, 1 Mother_RAT is
the measurement result of the GSM RSSI. 2 Tother_RAT is the
inter-RAT handover decision threshold. 3 Cell Individual Offset
(CIO) is the offset for the cell of another RAT. 4 H represents the
hysteresis, the setting of which can reduce false decisions caused
by signal jitters.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 16
Target B ADD
RatCs S UCE
Thd
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality requirement for the cell of another RAT during


inter-RAT CS handovers. For CS services, if "Inter-RAT
Reporting Mode" is set to EVENT_TRIGGER, this parameter is
used to set the criterion for triggering event 3A. That is, event 3A
can be triggered only when the quality of the target frequency is
higher than this threshold and the measurement quality of the
current CS services is lower than the quality of the currently
used frequency. If "Inter-RAT Reporting Mode" is set to
PERIODIC_TRIGGER, this parameter is used for inter-RAT
handover decisions on the RNC. Note that value 0 indicates the
value of this parameter is smaller than -110 dBm. If "Inter-RAT
Reporting Mode" is set to PERIODIC_TRIGGER, this
parameter is used for the assessment of coverage-based interRAT handovers. That is, Tother_RAT in the following formula.
This parameter is the absolute threshold of the cell of another
RAT (Received Signal Strength Indicator: RSSI) for the interRAT handover decisions. If the quality of the cell of another
RAT in the inter-RAT measurement report fulfills the following
criterion: Mother_RAT + CIO >= Tother_RAT + H/2 The system
starts the trigger timer, and makes the handover decision after the
timer expires. If the quality of the cell of another RAT fulfills the
following criterion before timeout: Mother_RAT + CIO <

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Tother_RAT - H/2 The RNC stops the timer and waits for
another inter-RAT measurement report. Where, 1 Mother_RAT is
the measurement result of the GSM RSSI. 2 Tother_RAT is the
inter-RAT handover decision threshold. 3 Cell Individual Offset
(CIO) is the offset for the cell of another RAT. 4 H represents the
hysteresis, the setting of which can reduce false decisions caused
by signal jitters.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 16
Target
RatR9
9PsTh
d

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality requirement for the cell of another RAT during


inter-RAT PS non-HSPA service handovers. For PS non-HSPA
services, if "Inter-RAT Reporting Mode" is set to
EVENT_TRIGGER, this parameter is used to set the criterion
for triggering event 3A. That is, event 3A can be triggered only
when the quality of the target frequency is higher than this
threshold and the measurement quality of the current PS services
is lower than the quality of the currently used frequency. If
"Inter-RAT Reporting Mode" is set to PERIODIC_TRIGGER,
this parameter is used for inter-RAT handover decisions on the
RNC. Note that value 0 indicates the value of this parameter is
smaller than -110 dBm. If "Inter-RAT Reporting Mode" is set to
PERIODIC_TRIGGER, this parameter is used for the
assessment of coverage-based inter-RAT handovers. That is,
Tother_RAT in the following formula. This parameter is the
absolute threshold of the cell of another RAT (RSSI) for the
inter-RAT handover decisions. If the quality of the cell of
another RAT in the inter-RAT measurement report fulfills the
following criterion: Mother_RAT + CIO >= Tother_RAT + H/2
The system starts the trigger timer, and makes the handover
decision after the timer expires. If the quality of the cell of
another RAT fulfills the following criterion before timeout:
Mother_RAT + CIO < Tother_RAT - H/2 The RNC stops the
timer and waits for another inter-RAT measurement report.
Where, 1 Mother_RAT is the measurement result of the GSM
RSSI. 2 Tother_RAT is the inter-RAT handover decision

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

threshold. 3 Cell Individual Offset (CIO) is the offset for the cell
of another RAT. 4 H represents the hysteresis, the setting of
which can reduce false decisions caused by signal jitters. Impact
on Radio Network Performance The setting of this parameter
affects number of hard handovers. If this parameter is set to a
small value, hard handovers are likely to be triggered, but pingpong handovers may occur. If this parameter is set to a large
value, hard handovers are unlikely to be triggered, but call drops
may occur.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 16
Target
RatR9
9PsTh
d

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality requirement for the cell of another RAT during


inter-RAT PS non-HSPA service handovers. For PS non-HSPA
services, if "Inter-RAT Reporting Mode" is set to
EVENT_TRIGGER, this parameter is used to set the criterion
for triggering event 3A. That is, event 3A can be triggered only
when the quality of the target frequency is higher than this
threshold and the measurement quality of the current PS services
is lower than the quality of the currently used frequency. If
"Inter-RAT Reporting Mode" is set to PERIODIC_TRIGGER,
this parameter is used for inter-RAT handover decisions on the
RNC. Note that value 0 indicates the value of this parameter is
smaller than -110 dBm. If "Inter-RAT Reporting Mode" is set to
PERIODIC_TRIGGER, this parameter is used for the
assessment of coverage-based inter-RAT handovers. That is,
Tother_RAT in the following formula. This parameter is the
absolute threshold of the cell of another RAT (RSSI) for the
inter-RAT handover decisions. If the quality of the cell of
another RAT in the inter-RAT measurement report fulfills the
following criterion: Mother_RAT + CIO >= Tother_RAT + H/2
The system starts the trigger timer, and makes the handover
decision after the timer expires. If the quality of the cell of
another RAT fulfills the following criterion before timeout:
Mother_RAT + CIO < Tother_RAT - H/2 The RNC stops the
timer and waits for another inter-RAT measurement report.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Where, 1 Mother_RAT is the measurement result of the GSM


RSSI. 2 Tother_RAT is the inter-RAT handover decision
threshold. 3 Cell Individual Offset (CIO) is the offset for the cell
of another RAT. 4 H represents the hysteresis, the setting of
which can reduce false decisions caused by signal jitters. Impact
on Radio Network Performance The setting of this parameter
affects number of hard handovers. If this parameter is set to a
small value, hard handovers are likely to be triggered, but pingpong handovers may occur. If this parameter is set to a large
value, hard handovers are unlikely to be triggered, but call drops
may occur.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 16
Target B ADD
RatHT S UCE
hd
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality requirement for the cell of another RAT during


inter-RAT HSPA handovers. For PS services, if "Inter-RAT
Reporting Mode" is set to EVENT_TRIGGER, this parameter is
used to set the criterion for triggering event 3A. That is, event 3A
can be triggered only when the quality of the target frequency is
higher than this threshold and the measurement quality of the
current PS services is lower than the quality of the currently used
frequency. If "Inter-RAT Reporting Mode" is set to
PERIODIC_TRIGGER, this parameter is used for inter-RAT
handover decisions on the RNC. Note that value 0 indicates the
value of this parameter is smaller than -110 dBm. If "Inter-RAT
Reporting Mode" is set to PERIODIC_TRIGGER, this
parameter is used for the assessment of coverage-based interRAT handovers. That is, Tother_RAT in the following formula.
This parameter is the absolute threshold of the cell of another
RAT (RSSI) for the inter-RAT handover decisions. If the quality
of the cell of another RAT in the inter-RAT measurement report
fulfills the following criterion: Mother_RAT + CIO >=
Tother_RAT + H/2 The system starts the trigger timer, and makes
the handover decision after the timer expires. If the quality of the
cell of another RAT fulfills the following criterion before
timeout: Mother_RAT + CIO < Tother_RAT - H/2 The RNC

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

stops the timer and waits for another inter-RAT measurement


report. Where, 1 Mother_RAT is the measurement result of the
GSM RSSI. 2 Tother_RAT is the inter-RAT handover decision
threshold. 3 Cell Individual Offset (CIO) is the offset for the cell
of another RAT. 4 H represents the hysteresis, the setting of
which can reduce false decisions caused by signal jitters. Impact
on Radio Network Performance The setting of this parameter
affects number of hard handovers. If this parameter is set to a
small value, hard handovers are likely to be triggered, but pingpong handovers may occur. If this parameter is set to a large
value, hard handovers are unlikely to be triggered, but call drops
may occur.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 16
Target B ADD
RatHT S UCE
hd
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality requirement for the cell of another RAT during


inter-RAT HSPA handovers. For PS services, if "Inter-RAT
Reporting Mode" is set to EVENT_TRIGGER, this parameter is
used to set the criterion for triggering event 3A. That is, event 3A
can be triggered only when the quality of the target frequency is
higher than this threshold and the measurement quality of the
current PS services is lower than the quality of the currently used
frequency. If "Inter-RAT Reporting Mode" is set to
PERIODIC_TRIGGER, this parameter is used for inter-RAT
handover decisions on the RNC. Note that value 0 indicates the
value of this parameter is smaller than -110 dBm. If "Inter-RAT
Reporting Mode" is set to PERIODIC_TRIGGER, this
parameter is used for the assessment of coverage-based interRAT handovers. That is, Tother_RAT in the following formula.
This parameter is the absolute threshold of the cell of another
RAT (RSSI) for the inter-RAT handover decisions. If the quality
of the cell of another RAT in the inter-RAT measurement report
fulfills the following criterion: Mother_RAT + CIO >=
Tother_RAT + H/2 The system starts the trigger timer, and makes
the handover decision after the timer expires. If the quality of the
cell of another RAT fulfills the following criterion before

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

timeout: Mother_RAT + CIO < Tother_RAT - H/2 The RNC


stops the timer and waits for another inter-RAT measurement
report. Where, 1 Mother_RAT is the measurement result of the
GSM RSSI. 2 Tother_RAT is the inter-RAT handover decision
threshold. 3 Cell Individual Offset (CIO) is the offset for the cell
of another RAT. 4 H represents the hysteresis, the setting of
which can reduce false decisions caused by signal jitters. Impact
on Radio Network Performance The setting of this parameter
affects number of hard handovers. If this parameter is set to a
small value, hard handovers are likely to be triggered, but pingpong handovers may occur. If this parameter is set to a large
value, hard handovers are unlikely to be triggered, but call drops
may occur.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 16
UsedF
reqCS
PSThd
RSCP

B
S
C
6
9
0
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T

Meaning: RSCP threshold for triggering a measurement-based


inter-frequency or inter-RAT handover from a cell that operates
at the currently used frequency for CS and PS combined services
For CS and PS combined services, this parameter configures
event 2B or 3A measurement control when the event-triggered
reporting mode is used for inter-frequency or inter-RAT
handovers. Event 2B or 3A is triggered when both of the
following conditions are met: -The signal quality in the cell that
operates at the currently used frequency is lower than this
threshold. -The criterion for TargetFreqCSPSMRABThdRscp or
TargetRatCSPSMRABThd is fulfilled.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Han
dov
er
Bas
ed
on
Cov
erag
e
UsedF
reqCS
PSThd
RSCP

B
S
C
6
9
1
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RSCP threshold for triggering a measurement-based


inter-frequency or inter-RAT handover from a cell that operates
at the currently used frequency for CS and PS combined services
For CS and PS combined services, this parameter configures
event 2B or 3A measurement control when the event-triggered
reporting mode is used for inter-frequency or inter-RAT
handovers. Event 2B or 3A is triggered when both of the
following conditions are met: -The signal quality in the cell that
operates at the currently used frequency is lower than this
threshold. -The criterion for TargetFreqCSPSMRABThdRscp or
TargetRatCSPSMRABThd is fulfilled.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UsedF
reqCS
PSThd
EcN0

B
S
C
6
9
0
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE
LLM
ULTI
RAB
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/N0 threshold for triggering a measurement-based


inter-frequency or inter-RAT handover from a cell that operates
at the currently used frequency for CS and PS combined services
For CS and PS combined services, this parameter configures
measurement control for event 2B or 3A when the eventtriggered reporting mode is used for inter-frequency or inter-RAT
handovers. Event 2B or 3A is triggered when both of the
following conditions are met: -The signal quality in the cell that
operates at the currently used frequency is lower than this
threshold. -The criterion for TargetFreqCSPSMRABThdEcN0 or
TargetRatCSPSMRABThd is fulfilled.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

UsedF
reqCS
PSThd
EcN0

B
S
C
6
9
1
0

ADD
UCE
LLM
ULTI
RAB
HOC
OV
MOD
UCE

W
RF
D02
03
02
W
RF
D-

Inte
r
Fre
que
ncy
Har
d
Han
dov

Meaning: Ec/N0 threshold for triggering a measurement-based


inter-frequency or inter-RAT handover from a cell that operates
at the currently used frequency for CS and PS combined services
For CS and PS combined services, this parameter configures
measurement control for event 2B or 3A when the eventtriggered reporting mode is used for inter-frequency or inter-RAT
handovers. Event 2B or 3A is triggered when both of the
following conditions are met: -The signal quality in the cell that
operates at the currently used frequency is lower than this

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

LLM
ULTI
RAB
HOC
OV

02 er
03 Bas
03 ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

threshold. -The criterion for TargetFreqCSPSMRABThdEcN0 or


TargetRatCSPSMRABThd is fulfilled.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

SET
UMU
LTIR
ABH
OCO
V

W
RF
D02
03
02
W
RF
D02
03
03

Meaning: Signal quality threshold for the target cell during a


decision on inter-RAT handover of CS and PS combined
services. If the event-triggered reporting mode is used for interRAT measurement, the RNC sends an event 3A-based
MEASUREMENT CONTROL message containing this
parameter to a UE. Event 3A is reported when both of the
following conditions are met: -The signal quality in the cell that
operates at the target frequency is higher than this threshold.
-The signal quality in the current cell is lower than the value of
UsedFreqCSPSThdEcN0 or UsedFreqCSPSThdRSCP. If the
periodical reporting mode is used for inter-RAT measurement,
the RNC makes a decision on coverage-based inter-RAT
handovers based on this parameter. Assume that the receiver
sensitivity of a GSM mobile phone is -102 dBm, compensation
for fast fading is 3 dB, compensation for slow fading is 5 dBm,
compensation for interference noise is 2 dB, and compensation
for ambient noise is 2 dB. Then, the outdoor receive level should
not be lower than -90 dBm. The value of this parameter varies

Target
RatCS
PSMR
ABTh
d

B
S
C
6
9
0
0

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r-

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Target
RatCS
PSMR
ABTh
d

B
S
C
6
9
1
0

SET
UMU
LTIR
ABH
OCO
V

W
RF
D02
03
02
W
RF
D02
03
03

Description

RA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

with the handover policy. To enable UEs to be handed over only


to GSM cells of high quality, set this parameter to a
comparatively large value, for example, -85 dBm.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48
Default Value: 16

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov

Meaning: Signal quality threshold for the target cell during a


decision on inter-RAT handover of CS and PS combined
services. If the event-triggered reporting mode is used for interRAT measurement, the RNC sends an event 3A-based
MEASUREMENT CONTROL message containing this
parameter to a UE. Event 3A is reported when both of the
following conditions are met: -The signal quality in the cell that
operates at the target frequency is higher than this threshold.
-The signal quality in the current cell is lower than the value of
UsedFreqCSPSThdEcN0 or UsedFreqCSPSThdRSCP. If the
periodical reporting mode is used for inter-RAT measurement,
the RNC makes a decision on coverage-based inter-RAT
handovers based on this parameter. Assume that the receiver
sensitivity of a GSM mobile phone is -102 dBm, compensation
for fast fading is 3 dB, compensation for slow fading is 5 dBm,
compensation for interference noise is 2 dB, and compensation
for ambient noise is 2 dB. Then, the outdoor receive level should
not be lower than -90 dBm. The value of this parameter varies
with the handover policy. To enable UEs to be handed over only
to GSM cells of high quality, set this parameter to a
comparatively large value, for example, -85 dBm.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48
Default Value: 16

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag
e
RsvU
32Par
a15

B
S
C
6
9
0
0

SET No Non
UAL ne e
GOR
SVPA
RA

Meaning: RRM algorithm reserved U32 para 15. The 32-bit


parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: 0~4294967295
Unit: None
Actual Value Range: 0~4294967295
Default Value: 0

RsvU
32Par
a15

B
S
C
6
9
1
0

SET No Non
UAL ne e
GOR
SVPA
RA

Meaning: RRM algorithm reserved U32 para 15. The 32-bit


parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: 0~4294967295
Unit: None
Actual Value Range: 0~4294967295
Default Value: 0

Penalt
yTime
rForC
MFail
Cov

B
S
C
6
9
0
0

SET
UHO
COM
M

Meaning: Penalty timer on compressed mode after coveragebased measurement expires. After coverage-based interfrequency measurement (inter-RAT or UMTS-to-LTE) expires,
this timer is started and a UE cannot start the compressed mode
for inter-frequency measurement (inter-RAT or UMTS-to-LTE)
during the period specified by this timer.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 10

W
RF
D02
03
09
W
RF
D02
03
02
W

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D02
03
03
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
on
DL
Qo
S
Penalt
yTime
rForC
MFail
Cov

B
S
C
6
9
1
0

SET
UHO
COM
M

W
RF
D02
03
09
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
04

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA

Meaning: Penalty timer on compressed mode after coveragebased measurement expires. After coverage-based interfrequency measurement (inter-RAT or UMTS-to-LTE) expires,
this timer is started and a UE cannot start the compressed mode
for inter-frequency measurement (inter-RAT or UMTS-to-LTE)
during the period specified by this timer.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 10

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
BSIC B ADD
Verify S UCE
C LLIN
6 TERR
9 ATH
0 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH

W
RF
D02
03
03
W
RF
D02
03
05

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag

Meaning: This parameter is used to control cells where interRAT measurement reports are triggered. If this parameter is set
to REQUIRED, the measurement reporting is triggered after the
BSIC of the measured cell is decoded correctly. If the parameter
is set to NOT_REQUIRE, the measurement reporting is
triggered regardless of whether the BSIC of the measured cell is
decoded correctly. This parameter is valid for both periodical
reporting mode and event-triggered reporting mode. However, to
ensure handover reliability, it is recommended that the system
reports only the cells whose BSIC is decoded correctly. If this
parameter is set to NOT_REQUIRED, handovers are likely to be
triggered, but handover reliability is lower than that in the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
ONC
OV

W
RF
D02
03
06
W
RF
D02
04
02

e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Description

situation this parameter is set to REQUIRED.


GUI Value Range: REQUIRED(Verify mode),
NOT_REQUIRE(Non-verify mode)
Unit: None
Actual Value Range: REQUIRED, NOT_REQUIRE
Default Value: REQUIRED(Verify mode)

BSIC B ADD W Inte Meaning: This parameter is used to control cells where interVerify S UCE RF rRAT measurement reports are triggered. If this parameter is set
C LLIN D- RA to REQUIRED, the measurement reporting is triggered after the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
6
9
1
0

TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

02
03
03
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas

Description

BSIC of the measured cell is decoded correctly. If the parameter


is set to NOT_REQUIRE, the measurement reporting is
triggered regardless of whether the BSIC of the measured cell is
decoded correctly. This parameter is valid for both periodical
reporting mode and event-triggered reporting mode. However, to
ensure handover reliability, it is recommended that the system
reports only the cells whose BSIC is decoded correctly. If this
parameter is set to NOT_REQUIRED, handovers are likely to be
triggered, but handover reliability is lower than that in the
situation this parameter is set to REQUIRED.
GUI Value Range: REQUIRED(Verify mode),
NOT_REQUIRE(Non-verify mode)
Unit: None
Actual Value Range: REQUIRED, NOT_REQUIRE
Default Value: REQUIRED(Verify mode)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ed
Dir
ect
Retr
y
HystF
orPrdI
nterFr
eq

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
02
01
W
RF
D02
04
02

Intr
a
Nod
eB
Soft
er
Han
dov
er
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Meaning: Hysteresis for the inter-frequency hard handover. This


parameter is reported periodically. This parameter is used to
estimate the inter-frequency handover on the RNC.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 0

HystF
orPrdI
nterFr
eq

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC

W
RF
D02
02
01
W
RF
D02
04
02

Intr
a
Nod
eB
Soft
er
Han
dov
er
Me
asur
eme
nt

Meaning: Hysteresis for the inter-frequency hard handover. This


parameter is reported periodically. This parameter is used to
estimate the inter-frequency handover on the RNC.
GUI Value Range: 0~29
Unit: 0.5dB; 0.5dBm
Actual Value Range: 0~14.5
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
OV

Description

Bas
ed
Dir
ect
Retr
y

RsvS B ADD No Non


witch0 S UCE ne e
C LLC
6 OAL
9 GOE
0 NHP
0 ARA
MOD
UCE
LLC
OAL
GOE
NHP
ARA

Meaning: CORRM algorithm reserved U32 Switch Para 0. The


32-bit parameter is reserved for further change request use.
Disuse statement: This parameter is used temporarily in patch
versions and will be replaced with a new parameter in later
versions. The new parameter ID reflects the parameter function.
Therefore, this parameter is not recommended for the
configuration interface.
GUI Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT32
Default Value: RESERVED_SWITCH_0_BIT1:0,
RESERVED_SWITCH_0_BIT2:0,
RESERVED_SWITCH_0_BIT3:0,
RESERVED_SWITCH_0_BIT4:0,
RESERVED_SWITCH_0_BIT5:0,
RESERVED_SWITCH_0_BIT6:0,
RESERVED_SWITCH_0_BIT7:0,
RESERVED_SWITCH_0_BIT8:0,
RESERVED_SWITCH_0_BIT9:0,
RESERVED_SWITCH_0_BIT10:0,
RESERVED_SWITCH_0_BIT11:0,
RESERVED_SWITCH_0_BIT12:0,
RESERVED_SWITCH_0_BIT13:0,
RESERVED_SWITCH_0_BIT14:0,
RESERVED_SWITCH_0_BIT15:0,
RESERVED_SWITCH_0_BIT16:0,
RESERVED_SWITCH_0_BIT17:0,
RESERVED_SWITCH_0_BIT18:0,
RESERVED_SWITCH_0_BIT19:0,
RESERVED_SWITCH_0_BIT20:0,
RESERVED_SWITCH_0_BIT21:0,
RESERVED_SWITCH_0_BIT22:0,
RESERVED_SWITCH_0_BIT23:0,
RESERVED_SWITCH_0_BIT24:0,
RESERVED_SWITCH_0_BIT25:0,
RESERVED_SWITCH_0_BIT26:0,
RESERVED_SWITCH_0_BIT27:0,
RESERVED_SWITCH_0_BIT28:0,
RESERVED_SWITCH_0_BIT29:0,
RESERVED_SWITCH_0_BIT30:0,
RESERVED_SWITCH_0_BIT31:0,
RESERVED_SWITCH_0_BIT32:0
RsvS B ADD
witch0 S UCE
C LLC
6 OAL
9 GOE

No Non Meaning: CORRM algorithm reserved U32 Switch Para 0. The


ne e
32-bit parameter is reserved for further change request use.
Disuse statement: This parameter is used temporarily in patch
versions and will be replaced with a new parameter in later
versions. The new parameter ID reflects the parameter function.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
1 NHP
0 ARA
MOD
UCE
LLC
OAL
GOE
NHP
ARA

Description

Therefore, this parameter is not recommended for the


configuration interface.
GUI Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Default Value: RESERVED_SWITCH_0_BIT1:0,
RESERVED_SWITCH_0_BIT2:0,
RESERVED_SWITCH_0_BIT3:0,
RESERVED_SWITCH_0_BIT4:0,
RESERVED_SWITCH_0_BIT5:0,
RESERVED_SWITCH_0_BIT6:0,
RESERVED_SWITCH_0_BIT7:0,
RESERVED_SWITCH_0_BIT8:0,
RESERVED_SWITCH_0_BIT9:0,
RESERVED_SWITCH_0_BIT10:0,
RESERVED_SWITCH_0_BIT11:0,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT12:0,
RESERVED_SWITCH_0_BIT13:0,
RESERVED_SWITCH_0_BIT14:0,
RESERVED_SWITCH_0_BIT15:0,
RESERVED_SWITCH_0_BIT16:0,
RESERVED_SWITCH_0_BIT17:0,
RESERVED_SWITCH_0_BIT18:0,
RESERVED_SWITCH_0_BIT19:0,
RESERVED_SWITCH_0_BIT20:0,
RESERVED_SWITCH_0_BIT21:0,
RESERVED_SWITCH_0_BIT22:0,
RESERVED_SWITCH_0_BIT23:0,
RESERVED_SWITCH_0_BIT24:0,
RESERVED_SWITCH_0_BIT25:0,
RESERVED_SWITCH_0_BIT26:0,
RESERVED_SWITCH_0_BIT27:0,
RESERVED_SWITCH_0_BIT28:0,
RESERVED_SWITCH_0_BIT29:0,
RESERVED_SWITCH_0_BIT30:0,
RESERVED_SWITCH_0_BIT31:0,
RESERVED_SWITCH_0_BIT32:0
TimeT
oTrig
ForPr
dInter
Freq

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
04
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Me

Meaning: Interval between reception of periodical reports and


triggering of the inter-frequency handover.
GUI Value Range: 0~64000
Unit: ms
Actual Value Range: 0~64000
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

asur
eme
nt
Bas
ed
Dir
ect
Retr
y
TimeT
oTrig
ForPr
dInter
Freq

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

CIOO B ADD
ffset
S U2G

W
RF
D02
03
02
W
RF
D02
04
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Meaning: Interval between reception of periodical reports and


triggering of the inter-frequency handover.
GUI Value Range: 0~64000
Unit: ms
Actual Value Range: 0~64000
Default Value: 0

W Intr Meaning: Cell individual offset (CIO) of neighboring GSM cells.


RF a
The value of this parameter together with the value of the CIO

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
C
6
9
0
0

NCE
LL
MOD
U2G
NCE
LL

D02
02
01
W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
05

Nod
eB
Soft
er
Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov

Description

parameter in the "ADD UEXT2GCELL" command determine


whether to perform a handover. For details, see 3GPP TS 25.331.
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Bas
ed
on
Ser
vice
CIOO B ADD
ffset
S U2G
C NCE
6 LL
9 MOD
1 U2G
0 NCE
LL

W
RF
D02
02
01
W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
05

Intr
a
Nod
eB
Soft
er
Han
dov
er
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on

Meaning: Cell individual offset (CIO) of neighboring GSM cells.


The value of this parameter together with the value of the CIO
parameter in the "ADD UEXT2GCELL" command determine
whether to perform a handover. For details, see 3GPP TS 25.331.
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Hystfo B ADD
rInter S UCE
RAT C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis for inter-RAT periodic reporting. The


hysteresis can be evaluated based on the Ec/N0 or RSCP. For
details about this parameter, see 3GPP TS 25.331.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

Hystfo B ADD
rInter S UCE
RAT C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas

Meaning: Hysteresis for inter-RAT periodic reporting. The


hysteresis can be evaluated based on the Ec/N0 or RSCP. For
details about this parameter, see 3GPP TS 25.331.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UCE
LLIN
TERR
ATH
OCO
V
TimeT
oTrig
ForVe
rify

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

Description

ed
on
Cov
erag
e
W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed

Meaning: Time delay for triggering handovers to GSM cells with


verified BSIC. During the period specified by this parameter, if
the signal quality in a neighboring GSM cell meets inter-RAT
handover decision requirements and the neighboring GSM cell is
verified, an inter-RAT handover is triggered. For details about
this parameter, see 3GPP TS 25.331.
GUI Value Range: 0~64000
Unit: ms
Actual Value Range: 0~64000
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Dir
ect
Retr
y
TimeT
oTrig
ForVe
rify

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect

Meaning: Time delay for triggering handovers to GSM cells with


verified BSIC. During the period specified by this parameter, if
the signal quality in a neighboring GSM cell meets inter-RAT
handover decision requirements and the neighboring GSM cell is
verified, an inter-RAT handover is triggered. For details about
this parameter, see 3GPP TS 25.331.
GUI Value Range: 0~64000
Unit: ms
Actual Value Range: 0~64000
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Retr
y
TimeT
oTrig
ForNo
nVerif
y

B
S
C
6
9
0
0

SET
UINT
ERR
ATH
OCO
V

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Meaning: Maximum time delay for triggering handovers to GSM


cells with non-verified BSIC. BSIC stands for base transceiver
station identity code of a GSM cell. During the period specified
by this parameter, if the signal quality in a neighboring GSM cell
meets inter-RAT handover decision requirements and the
neighboring GSM cell is not verified, an inter-RAT handover is
triggered. If this parameter is set to 65535, the RNC does not
perform inter-RAT handovers to non-verified GSM cells. If this
parameter is set to a large value, the average number of
handovers decreases, but call drops may occur. For details, see
3GPP TS 25.331.
GUI Value Range: 0~64000;65535
Unit: ms
Actual Value Range: 0~64000, 65535
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
TimeT
oTrig
ForNo
nVerif
y

B
S
C
6
9
1
0

SET
UINT
ERR
ATH
OCO
V

BSIC B ADD
Verify S UCE

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Description

Meaning: Maximum time delay for triggering handovers to GSM


cells with non-verified BSIC. BSIC stands for base transceiver
station identity code of a GSM cell. During the period specified
by this parameter, if the signal quality in a neighboring GSM cell
meets inter-RAT handover decision requirements and the
neighboring GSM cell is not verified, an inter-RAT handover is
triggered. If this parameter is set to 65535, the RNC does not
perform inter-RAT handovers to non-verified GSM cells. If this
parameter is set to a large value, the average number of
handovers decreases, but call drops may occur. For details, see
3GPP TS 25.331.
GUI Value Range: 0~64000;65535
Unit: ms
Actual Value Range: 0~64000, 65535
Default Value: 0

W Inte Meaning: This parameter is used to control cells where interRF rRAT measurement reports are triggered. If this parameter is set

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
C
6
9
0
0

LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

RA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt

Description

to REQUIRED, the measurement reporting is triggered after the


BSIC of the measured cell is decoded correctly. If the parameter
is set to NOT_REQUIRE, the measurement reporting is
triggered regardless of whether the BSIC of the measured cell is
decoded correctly. This parameter is valid for both periodical
reporting mode and event-triggered reporting mode. However, to
ensure handover reliability, it is recommended that the system
reports only the cells whose BSIC is decoded correctly. If this
parameter is set to NOT_REQUIRED, handovers are likely to be
triggered, but handover reliability is lower than that in the
situation this parameter is set to REQUIRED.
GUI Value Range: REQUIRED(Verify mode),
NOT_REQUIRE(Non-verify mode)
Unit: None
Actual Value Range: REQUIRED, NOT_REQUIRE
Default Value: REQUIRED(Verify mode)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
Dir
ect
Retr
y
BSIC B ADD
Verify S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er

Meaning: This parameter is used to control cells where interRAT measurement reports are triggered. If this parameter is set
to REQUIRED, the measurement reporting is triggered after the
BSIC of the measured cell is decoded correctly. If the parameter
is set to NOT_REQUIRE, the measurement reporting is
triggered regardless of whether the BSIC of the measured cell is
decoded correctly. This parameter is valid for both periodical
reporting mode and event-triggered reporting mode. However, to
ensure handover reliability, it is recommended that the system
reports only the cells whose BSIC is decoded correctly. If this
parameter is set to NOT_REQUIRED, handovers are likely to be
triggered, but handover reliability is lower than that in the
situation this parameter is set to REQUIRED.
GUI Value Range: REQUIRED(Verify mode),
NOT_REQUIRE(Non-verify mode)
Unit: None
Actual Value Range: REQUIRED, NOT_REQUIRE
Default Value: REQUIRED(Verify mode)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y
NPrior B ADD
ity
S UCE
C LLNF
6 REQP
9 RIOI
0 NFO
0 MOD
UCE
LLNF
REQP
RIOI
NFO

W
RF
D02
02
01
W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D01
06

Intr
a
Nod
eB
Soft
er
Han
dov
er
Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han

Meaning: This parameter specifies the absolute priority level of


the E-UTRA frequency. The UE compares the value of this
parameter with the absolute priority level of the serving cell, and
specifies the target frequency based on the comparison result.
That is, when the value of this parameter is greater than the
priority level of the serving cell, the UE measures the
neighboring frequency. If the signal of cells on the neighboring
frequency satisfies relevant requirements, the UE initiates the
cell reselection. When the value of this parameter is smaller than
the priority level of the serving cell, the UE measures the
neighboring frequency only when the signal of the serving cell is
weak. If the signal of cells on the neighboring frequency satisfies
relevant requirements, the UE initiates the cell reselection. The
value of this parameter is set during network planning. The
greater the value of this parameter is, the easier the UE reselects
a cell on this frequency, the smaller the value of this parameter
is, the harder the UE reselects a cell on this frequency. For
details on this parameter, see 3GPP TS 25.304.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
14
04
W
RF
D02
03
08
02
W
RF
D02
12
00
W
RF
D14
02
26
W
RF
D02
03
10
W
RF
D15
02
19
W
RF
D02
03

dov
er
HS
UP
A
2ms
/10
ms
TTI
Han
dov
er
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Fast
Ret
urn
fro
m

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
08
W
RF
D01
06
12
04
W
RF
D02
03
09
W
RF
D02
01
26
W
RF
D02
03
01
W
RF
D02
01
29
W
RF
D02
03
02

UM
TS
to
LTE
3G/
2G
Co
mm
on
Loa
d
Ma
nag
eme
nt
Cov
erag
e
Bas
ed
PS
Red
irec
tion
fro
m
UM
TS
to
LTE
Inte
rRA
T
Han
dov
er
Pha
se 2

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D02
03
03
W
RF
D02
03
04
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
03
08
01

HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Mo
bilit
y
Bet
wee
n
UM
TS
and
LTE
Pha
se 1
Intr
a
Fre
que

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
ncy
Har
d
Han
dov
er
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to
LTE
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

T
Han
dov
er
Bas
ed
on
Loa
d
NA
CC(
Net
wor
k
Ass
iste
d
Cell
Cha
nge
)
NPrior B ADD
ity
S UCE
C LLNF
6 REQP
9 RIOI
1 NFO
0 MOD
UCE
LLNF
REQP
RIOI
NFO

W
RF
D02
02
01
W
RF
D02
02
03
W
RF
D02
02

Intr
a
Nod
eB
Soft
er
Han
dov
er
Inte
r
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the absolute priority level of


the E-UTRA frequency. The UE compares the value of this
parameter with the absolute priority level of the serving cell, and
specifies the target frequency based on the comparison result.
That is, when the value of this parameter is greater than the
priority level of the serving cell, the UE measures the
neighboring frequency. If the signal of cells on the neighboring
frequency satisfies relevant requirements, the UE initiates the
cell reselection. When the value of this parameter is smaller than
the priority level of the serving cell, the UE measures the
neighboring frequency only when the signal of the serving cell is
weak. If the signal of cells on the neighboring frequency satisfies
relevant requirements, the UE initiates the cell reselection. The
value of this parameter is set during network planning. The
greater the value of this parameter is, the easier the UE reselects
a cell on this frequency, the smaller the value of this parameter
is, the harder the UE reselects a cell on this frequency. For

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
02
W
RF
D01
06
14
04
W
RF
D02
03
08
02
W
RF
D02
12
00
W
RF
D14
02
26
W
RF
D02
03
10
W
RF
D15
02

Intr
a
RN
C
Soft
Han
dov
er
HS
UP
A
2ms
/10
ms
TTI
Han
dov
er
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur

Description

details on this parameter, see 3GPP TS 25.304.


GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
19
W
RF
D02
03
08
W
RF
D01
06
12
04
W
RF
D02
03
09
W
RF
D02
01
26
W
RF
D02
03
01
W
RF
D02
01
29

e)
Fast
Ret
urn
fro
m
UM
TS
to
LTE
3G/
2G
Co
mm
on
Loa
d
Ma
nag
eme
nt
Cov
erag
e
Bas
ed
PS
Red
irec
tion
fro
m
UM
TS
to
LTE
Inte
rRA

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
04
W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
03
08
01

T
Han
dov
er
Pha
se 2
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Mo
bilit
y
Bet
wee
n
UM
TS
and
LTE

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Pha
se 1
Intr
a
Fre
que
ncy
Har
d
Han
dov
er
PS
Ser
vice
Red
irec
tion
fro
m
UM
TS
to
LTE
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
NA
CC(
Net
wor
k
Ass
iste
d
Cell
Cha
nge
)
HOPri B ADD
o
S U2G
C NCE
6 LL
9 MOD
0 U2G
0 NCE
LL

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov

Meaning: Priority of the neighboring cell as a target cell for a


handover. Value 0 indicates the highest priority and value 7
indicates the lowest priority. When this parameter takes effect,
the RNC preferentially selects the cell with the highest priority
as the target cell. If two or more cells have the same priority, the
RNC selects a target cell with the best signal quality.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag
e
HOPri B ADD
o
S U2G
C NCE
6 LL
9 MOD
1 U2G
0 NCE
LL

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Priority of the neighboring cell as a target cell for a


handover. Value 0 indicates the highest priority and value 7
indicates the lowest priority. When this parameter takes effect,
the RNC preferentially selects the cell with the highest priority
as the target cell. If two or more cells have the same priority, the
RNC selects a target cell with the best signal quality.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

RatCe B ADD
llType S UEX
C T2GC
6 ELL
9 MOD
0 UEX
0 T2GC
ELL

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed

Meaning: Identifying the type of the inter-RAT cell


NO_CAPABILITY indicates that the capacity of the GSM cell
remains unknown. It is not recommended to set the cell type to
NO_CAPABILITY. If the cell type is NO_CAPABILITY, the
inter-RAT handover cannot be triggered.
GUI Value Range: NO_CAPABILITY(Cell capability unknown),
GSM(GSM), GPRS(GPRS), EDGE(EDGE)
Unit: None
Actual Value Range: NO_CAPABILITY, GSM, GPRS, EDGE
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

03 on
06 Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
RatCe B ADD
llType S UEX
C T2GC
6 ELL
9 MOD
1 UEX
0 T2GC
ELL

W
RF
D02
03
09
W
RF
D02

Inte
rRA
T
Han
dov
er
Bas
ed
on

Meaning: Identifying the type of the inter-RAT cell


NO_CAPABILITY indicates that the capacity of the GSM cell
remains unknown. It is not recommended to set the cell type to
NO_CAPABILITY. If the cell type is NO_CAPABILITY, the
inter-RAT handover cannot be triggered.
GUI Value Range: NO_CAPABILITY(Cell capability unknown),
GSM(GSM), GPRS(GPRS), EDGE(EDGE)
Unit: None
Actual Value Range: NO_CAPABILITY, GSM, GPRS, EDGE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
03
03
W
RF
D02
03
05
W
RF
D02
03
06

DL Default Value: None


Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

d
Req2
GCap

B
S
C
6
9
0
0

ADD
UTY
PRA
BBA
SIC
MOD
UTY
PRA
BBA
SIC

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
08
02
W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP

Meaning: Minimum capability of the 2G cell required for interRAT handover from 3G network to 2G network. If the 2G cell is
not capable, the handover will not be performed. An EDGE cell
is more capable of supporting PS services than a GPRS cell,
whereas a GPRS cell more capable than a GSM cell.
GUI Value Range: GSM, GPRS, EDGE
Unit: None
Actual Value Range: GSM, GPRS, EDGE
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RS
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Req2
GCap

B
S
C
6
9
1
0

ADD
UTY
PRA
BBA
SIC
MOD
UTY
PRA
BBA
SIC

W
RF
D02
03
09
W
RF
D02
03
03
W

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: Minimum capability of the 2G cell required for interRAT handover from 3G network to 2G network. If the 2G cell is
not capable, the handover will not be performed. An EDGE cell
is more capable of supporting PS services than a GPRS cell,
whereas a GPRS cell more capable than a GSM cell.
GUI Value Range: GSM, GPRS, EDGE
Unit: None
Actual Value Range: GSM, GPRS, EDGE
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D02
03
08
02
W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
r-

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RA
T
Han
dov
er
Bas
ed
on
Loa
d
SHInd B
S
C
6
9
0
0

ADD
UTY
PRA
BBA
SIC
MOD
UTY
PRA
BBA
SIC

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
08
02
W
RF
D02
03
05
W
RF
D-

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PS
Han

Meaning: Service handover attribute. If the


HO_INTER_RAT_RNC_SERVICE_HO_SWITCH is set to ON,
the service handover setting of this parameter is applied.
Otherwise, the service handover setting assigned by the CN is
applied. - HO_TO_GSM_SHOULD_BE_PERFORM: Handover
to the 2G network is performed so long as 2G signals are
available. - HO_TO_GSM_SHOULD_NOT_BE_PERFORM:
Handover to the 2G network is performed when 3G signals are
weak but 2G signals are strong. HO_TO_GSM_SHALL_NOT_BE_PERFORM: Handover to the
2G network is not performed even if 3G signals are weak but 2G
signals are strong.
GUI Value Range: HO_TO_GSM_SHOULD_BE_PERFORM,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM,
HO_TO_GSM_SHALL_NOT_BE_PERFORM
Unit: None
Actual Value Range:
HO_TO_GSM_SHOULD_BE_PERFORM,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM,
HO_TO_GSM_SHALL_NOT_BE_PERFORM
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

02 dov
03 er
06 Bet
wee
n
UM
TS
and
GP
RS
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
SHInd B
S
C
6

ADD
UTY
PRA
BBA

W
RF
D02

Inte
rRA
T

Meaning: Service handover attribute. If the


HO_INTER_RAT_RNC_SERVICE_HO_SWITCH is set to ON,
the service handover setting of this parameter is applied.
Otherwise, the service handover setting assigned by the CN is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
9 SIC
1 MOD
0 UTY
PRA
BBA
SIC

03
09
W
RF
D02
03
03
W
RF
D02
03
08
02
W
RF
D02
03
05
W
RF
D02
03
06

Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
Inte
rRA
T
Han

Description

applied. - HO_TO_GSM_SHOULD_BE_PERFORM: Handover


to the 2G network is performed so long as 2G signals are
available. - HO_TO_GSM_SHOULD_NOT_BE_PERFORM:
Handover to the 2G network is performed when 3G signals are
weak but 2G signals are strong. HO_TO_GSM_SHALL_NOT_BE_PERFORM: Handover to the
2G network is not performed even if 3G signals are weak but 2G
signals are strong.
GUI Value Range: HO_TO_GSM_SHOULD_BE_PERFORM,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM,
HO_TO_GSM_SHALL_NOT_BE_PERFORM
Unit: None
Actual Value Range:
HO_TO_GSM_SHOULD_BE_PERFORM,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM,
HO_TO_GSM_SHALL_NOT_BE_PERFORM
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
SuppR B ADD
IMFla S UEX
g
C T2GC
6 ELL
9 MOD
0 UEX
0 T2GC
ELL

W
RF
D07
00
05
W
RF
D02
03
08
01

NA
CC
Pro
ced
ure
Opt
imi
zati
on
Bas
ed
on
Iurg
NA
CC(
Net
wor
k

Meaning: Identifying whether the inter-RAT cell supports RIM.


(RIM is used to obtain the SI/PSI information of the inter-RAT
cell.) For the details of RIM process, refer to the 3GPP TS
25.901 protocol. RIM:RAN Information Management;
SI:System Information; PSI:Packet System Information;
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Ass
iste
d
Cell
Cha
nge
)
SuppR B ADD
IMFla S UEX
g
C T2GC
6 ELL
9 MOD
1 UEX
0 T2GC
ELL

W
RF
D07
00
05
W
RF
D02
03
08
01

NA
CC
Pro
ced
ure
Opt
imi
zati
on
Bas
ed
on
Iurg
NA
CC(
Net
wor
k
Ass
iste
d
Cell
Cha
nge
)

Meaning: Identifying whether the inter-RAT cell supports RIM.


(RIM is used to obtain the SI/PSI information of the inter-RAT
cell.) For the details of RIM process, refer to the 3GPP TS
25.901 protocol. RIM:RAN Information Management;
SI:System Information; PSI:Packet System Information;
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

SuppP B ADD
SHOF S UEX
lag
C T2GC
6 ELL

W
RF
D02

PS
Han
dov
er

Meaning: Identifying whether the inter-RAT cell supports PS


HO. TRUE indicates that the inter-RAT cell is able to perform
the handover procedure with relocation. FALSE indicates that
the cell is unable to do so.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
9 MOD 03 Bet
0 UEX 08 wee
0 T2GC 02 n
ELL
UM
TS
and
GP
RS

Description

GUI Value Range: FALSE, TRUE


Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

SuppP B ADD
SHOF S UEX
lag
C T2GC
6 ELL
9 MOD
1 UEX
0 T2GC
ELL

W
RF
D02
03
08
02

PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS

Meaning: Identifying whether the inter-RAT cell supports PS


HO. TRUE indicates that the inter-RAT cell is able to perform
the handover procedure with relocation. FALSE indicates that
the cell is unable to do so.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

Penalt
yTime
rForIF
HoFai
l

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que

Meaning: Duration after which the coverage-based interfrequency handover, inter-frequency blind handover triggered by
event 1F, or QoS-based inter-frequency handover to a cell can be
re-initiated after a failure of such handover to this cell due to the
air interface faults.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Penalt
yTime
rForIF
HoFai
l

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Meaning: Duration after which the coverage-based interfrequency handover, inter-frequency blind handover triggered by
event 1F, or QoS-based inter-frequency handover to a cell can be
re-initiated after a failure of such handover to this cell due to the
air interface faults.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Cov
erag
e
IFHoF B ADD
ailNu S UCE
m
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Maximum number of consecutive handover failures


after a coverage-based inter-frequency handover, inter-frequency
blind handover triggered by event 1F, or QoS-based interfrequency handover to a cell fails due to the air interface faults.
When the number of consecutive handover failures of a UE in a
call is greater than the value of this parameter, the RNC
penalizes the UE and the UE cannot initiate such inter-frequency
handovers within the penalty period.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~63
Default Value: 3

IFHoF B ADD
ailNu S UCE
m
C LLIN
6 TERF
9 REQ

W
RF
D02
03

Inte
rRA
T
Han

Meaning: Maximum number of consecutive handover failures


after a coverage-based inter-frequency handover, inter-frequency
blind handover triggered by event 1F, or QoS-based interfrequency handover to a cell fails due to the air interface faults.
When the number of consecutive handover failures of a UE in a

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

UEPe
naltyT
imerF
orIFH
oFail

Description

1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

09
W
RF
D02
03
02

dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

call is greater than the value of this parameter, the RNC


penalizes the UE and the UE cannot initiate such inter-frequency
handovers within the penalty period.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~63
Default Value: 3

B
S
C
6
9
0
0

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte

Meaning: Duration after which the coverage-based interfrequency handover, inter-frequency blind handover triggered by
event 1F, or QoS-based inter-frequency handover to a cell can be
re-initiated after a failure of such handover to this cell due to the
air interface faults.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
UEPe
naltyT
imerF
orIFH
oFail

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Duration after which the coverage-based interfrequency handover, inter-frequency blind handover triggered by
event 1F, or QoS-based inter-frequency handover to a cell can be
re-initiated after a failure of such handover to this cell due to the
air interface faults.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
on
Cov
erag
e
InterF
reqLD
HOM
ethod
Selecti
on

B
S
C
6
9
0
0

ADD
UCE
LLLD
R
MOD
UCE
LLLD
R

W
RF
D02
01
60
W
RF
D02
01
06
W
RF
D02
01
03

Enh
anc
ed
Mul
tiba
nd
Ma
nag
eme
nt
Loa
d
Res
huff
ling
Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e

Meaning: Whether to perform LDR-triggered measurementbased inter-frequency handover or LDR-triggered blind interfrequency handover. Measurement-based handover applies to
scenarios where cells in a network use different frequency bands
and cover different areas, while blind handover applies to
scenarios where these cells use the same frequency band and
cover the same area. If these two types of scenario coexist in a
network, you are advised to set this parameter to
PRIOBLINDHO. When this parameter is set to PRIOBLINDHO,
the RNC preferentially performs LDR-triggered blind interfrequency handover. If none of the configured neighboring cells
for blind handover meets the related requirements, the RNC then
selects one cell from the configured cells that support LDRtriggered measurement-based inter-frequency handover as the
target cell.
GUI Value Range: BLINDHO(BLINDHO),
MEASUREHO(MEASUREHO),
PRIOBLINDHO(PRIOBLINDHO)
Unit: None
Actual Value Range: BLINDHO, MEASUREHO,
PRIOBLINDHO
Default Value: BLINDHO(BLINDHO)

InterF
reqLD
HOM
ethod
Selecti
on

B
S
C
6
9
1

ADD
UCE
LLLD
R
MOD
UCE

W
RF
D02
01
60

Enh
anc
ed
Mul
tiba
nd

Meaning: Whether to perform LDR-triggered measurementbased inter-frequency handover or LDR-triggered blind interfrequency handover. Measurement-based handover applies to
scenarios where cells in a network use different frequency bands
and cover different areas, while blind handover applies to
scenarios where these cells use the same frequency band and

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Blind
HOInt
rafreq
MRInt
erval

Description

0 LLLD W Ma
R
RF nag
D- eme
02 nt
01 Loa
06 d
W Res
RF huff
D- ling
02 Inte
01 r
03 Fre
que
ncy
Loa
d
Bal
anc
e

cover the same area. If these two types of scenario coexist in a


network, you are advised to set this parameter to
PRIOBLINDHO. When this parameter is set to PRIOBLINDHO,
the RNC preferentially performs LDR-triggered blind interfrequency handover. If none of the configured neighboring cells
for blind handover meets the related requirements, the RNC then
selects one cell from the configured cells that support LDRtriggered measurement-based inter-frequency handover as the
target cell.
GUI Value Range: BLINDHO(BLINDHO),
MEASUREHO(MEASUREHO),
PRIOBLINDHO(PRIOBLINDHO)
Unit: None
Actual Value Range: BLINDHO, MEASUREHO,
PRIOBLINDHO
Default Value: BLINDHO(BLINDHO)

B
S
C
6
9
0
0

Meaning: Interval between intra-frequency measurement reports


reported by the UE for inter-frequency blind handover triggered
by load reshuffling (LDR). If the number of intra-frequency
measurement reports continuously reported by the UE during the
interval reaches or exceeds the number of intra-frequency
measurement reports for a blind handover
("BlindHOIntrafreqMRAmount"), the RNC initiates a blind
handover. Measurements are terminated if the UE reports a
measurement report indicating that the handover criteria are not
met. In this case, the RNC does not initiate a blind handover to
the target cell.
GUI Value Range: D250, D500
Unit: ms
Actual Value Range: 250, 500
Default Value: D250

SET
UINT
RAF
REQ
HO

W
RF
D02
01
03

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e

Blind B SET W Inte Meaning: Interval between intra-frequency measurement reports


HOInt S UINT RF r
reported by the UE for inter-frequency blind handover triggered

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

rafreq C RAF
MRInt 6 REQ
erval 9 HO
1
0

D02
01
03

Fre
que
ncy
Loa
d
Bal
anc
e

by load reshuffling (LDR). If the number of intra-frequency


measurement reports continuously reported by the UE during the
interval reaches or exceeds the number of intra-frequency
measurement reports for a blind handover
("BlindHOIntrafreqMRAmount"), the RNC initiates a blind
handover. Measurements are terminated if the UE reports a
measurement report indicating that the handover criteria are not
met. In this case, the RNC does not initiate a blind handover to
the target cell.
GUI Value Range: D250, D500
Unit: ms
Actual Value Range: 250, 500
Default Value: D250

Blind
HOInt
rafreq
MRA
mount

B
S
C
6
9
0
0

SET
UINT
RAF
REQ
HO

W
RF
D02
01
03

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e

Meaning: The number of required measurement reports for


triggering an inter-frequency blind handover. If the number of
intra-frequency measurement reports continuously reported by
the UE reaches or exceeds the number of intra-frequency
measurement reports for triggering a blind handover
("BlindHOIntrafreqMRAmount"), the RNC initiates a blind
handover. Measurements are terminated if the UE reports a
measurement report indicating that the handover criteria are not
met. In this case, the RNC does not initiate a blind handover to
the target cell.
GUI Value Range: D1, D2, D4, D8
Unit: None
Actual Value Range: 1, 2, 4, 8
Default Value: D2

Blind
HOInt
rafreq
MRA
mount

B
S
C
6
9
1
0

SET
UINT
RAF
REQ
HO

W
RF
D02
01
03

Inte
r
Fre
que
ncy
Loa
d
Bal
anc

Meaning: The number of required measurement reports for


triggering an inter-frequency blind handover. If the number of
intra-frequency measurement reports continuously reported by
the UE reaches or exceeds the number of intra-frequency
measurement reports for triggering a blind handover
("BlindHOIntrafreqMRAmount"), the RNC initiates a blind
handover. Measurements are terminated if the UE reports a
measurement report indicating that the handover criteria are not
met. In this case, the RNC does not initiate a blind handover to

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Blind
HOQu
alityC
onditi
on

B
S
C
6
9
0
0

ADD
UINT
ERFR
EQN
CELL
MOD
UINT
ERFR
EQN
CELL

W
RF
D15
02
01
W
RF
D15
02
32

Description

the target cell.


GUI Value Range: D1, D2, D4, D8
Unit: None
Actual Value Range: 1, 2, 4, 8
Default Value: D2

Ma
cro
&
Mic
ro
Cocarr
ier
Upl
ink
Inte
rfer
enc
e
Con
trol
Mul
tiba
nd
Dir
ect
Retr
y
Bas
ed
on
UE
Loc
atio
n

Meaning: RSCP threshold for triggering blind handovers. If the


RSCP value of the current cell exceeds the value of this
parameter, the RNC initiates a blind handover to switch the UE
to the inter-frequency neighboring cell. This threshold applies to
load-balancing-based blind handovers, and directed retries from
low-frequency-band cells to high-frequency-band cells.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Blind B ADD W Ma
HOQu S UINT RF cro

Meaning: RSCP threshold for triggering blind handovers. If the


RSCP value of the current cell exceeds the value of this

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

alityC C ERFR
onditi 6 EQN
on
9 CELL
1 MOD
0 UINT
ERFR
EQN
CELL

D15
02
01
W
RF
D15
02
32

&
Mic
ro
Cocarr
ier
Upl
ink
Inte
rfer
enc
e
Con
trol
Mul
tiba
nd
Dir
ect
Retr
y
Bas
ed
on
UE
Loc
atio
n

parameter, the RNC initiates a blind handover to switch the UE


to the inter-frequency neighboring cell. This threshold applies to
load-balancing-based blind handovers, and directed retries from
low-frequency-band cells to high-frequency-band cells.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

PrdRe B ADD
portInt S UCE
erval C LLM
6 CLD
9 R
0 MOD
0 UCE
LLM
CLD
R

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Interval for periodically sending inter-frequency


measurement reports. After inter-frequency measurement starts,
the UE periodically reports the RSCP and Ec/N0 of the target
cell at the interval specified by this parameter.
GUI Value Range: D250, D500, D1000, D2000, D3000, D4000,
D6000, D8000, D12000, D16000, D20000, D24000, D28000,
D32000, D64000
Unit: ms
Actual Value Range: 250, 500, 1000, 2000, 3000, 4000, 6000,
8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas Default Value: D3000


ed
on
Cov
erag
e
PrdRe B ADD
portInt S UCE
erval C LLM
6 CLD
9 R
1 MOD
0 UCE
LLM
CLD
R

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Interval for periodically sending inter-frequency


measurement reports. After inter-frequency measurement starts,
the UE periodically reports the RSCP and Ec/N0 of the target
cell at the interval specified by this parameter.
GUI Value Range: D250, D500, D1000, D2000, D3000, D4000,
D6000, D8000, D12000, D16000, D20000, D24000, D28000,
D32000, D64000
Unit: ms
Actual Value Range: 250, 500, 1000, 2000, 3000, 4000, 6000,
8000, 12000, 16000, 20000, 24000, 28000, 32000, 64000
Default Value: D3000

Target
FreqT
hdRsc
p

W
RF
D02
01
03
W
RF
D02
01
60

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Enh
anc
ed
Mul
tiba

Meaning: RSCP threshold of the target cell for triggering interfrequency MCLDR handovers. This parameter is used to
evaluate the signal quality in the periodic reports. Interfrequency handovers are triggered only when the signal quality
of the target cell is higher than the value of this parameter. The
threshold can be reached only when RSCP and Ec/N0 of the
target cell are above the RSCP and Ec/N0 specified by this
parameter.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

B
S
C
6
9
0
0

ADD
UCE
LLM
CLD
R
MOD
UCE
LLM
CLD
R

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

nd
Ma
nag
eme
nt
Target
FreqT
hdRsc
p

B
S
C
6
9
1
0

ADD
UCE
LLM
CLD
R
MOD
UCE
LLM
CLD
R

W
RF
D02
01
03
W
RF
D02
01
60

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Enh
anc
ed
Mul
tiba
nd
Ma
nag
eme
nt

Meaning: RSCP threshold of the target cell for triggering interfrequency MCLDR handovers. This parameter is used to
evaluate the signal quality in the periodic reports. Interfrequency handovers are triggered only when the signal quality
of the target cell is higher than the value of this parameter. The
threshold can be reached only when RSCP and Ec/N0 of the
target cell are above the RSCP and Ec/N0 specified by this
parameter.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -92

Target
FreqT
hdEc
N0

B
S
C
6
9
0
0

ADD
UCE
LLM
CLD
R
MOD
UCE
LLM
CLD
R

W
RF
D02
01
03
W
RF
D02
01
60

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Enh
anc

Meaning: Ec/N0 threshold of the target cell for triggering interfrequency MCLDR handovers. This parameter is used to
evaluate the signal quality in the periodic reports. Interfrequency handovers are triggered only when the signal quality
of the target cell is higher than the value of this parameter. The
threshold can be reached only when RSCP and Ec/N0 of the
target cell are above the RSCP and Ec/N0 specified by this
parameter.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ed Default Value: -12


Mul
tiba
nd
Ma
nag
eme
nt
Target
FreqT
hdEc
N0

B
S
C
6
9
1
0

ADD
UCE
LLM
CLD
R
MOD
UCE
LLM
CLD
R

W
RF
D02
01
03
W
RF
D02
01
60

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Enh
anc
ed
Mul
tiba
nd
Ma
nag
eme
nt

Meaning: Ec/N0 threshold of the target cell for triggering interfrequency MCLDR handovers. This parameter is used to
evaluate the signal quality in the periodic reports. Interfrequency handovers are triggered only when the signal quality
of the target cell is higher than the value of this parameter. The
threshold can be reached only when RSCP and Ec/N0 of the
target cell are above the RSCP and Ec/N0 specified by this
parameter.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -12

TrigTi B ADD
me3C S UCE
C LLIN
6 TERR
9 ATH
0 ONC
0 OV
MOD
UCE

W
RF
D02
03
05
W
RF
D-

Inte
rRA
T
Han
dov
er
Bas
ed

Meaning: Time delay to trigger event 3C.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
LLIN
TERR
ATH
ONC
OV

02
03
06
W
RF
D02
04
02

on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

TrigTi B ADD
me3C S UCE
C LLIN
6 TERR
9 ATH
1 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC

W
RF
D02
03
05
W
RF
D02
03
06
W

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte

Description

Meaning: Time delay to trigger event 3C.


GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

CIO

B
S
C
6
9
0
0

OV

RF
D02
04
02

rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

ADD
UEX
T2GC
ELL
MOD
UEX
T2GC
ELL

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T

Description

Meaning: It is set according to the topographic feature.For


details about this parameter, see 3GPP TS 25.331. This
parameter is used for the inter-RAT handover decision in
combination with the neighboring cell oriented CIO. The larger
the sum, the higher the handover priority of the GSM cell. The
smaller the sum, the lower the handover priority of the GSM
cell. The parameter is generally set to 0.
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

05 Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
CIO

B
S
C
6
9
1
0

ADD
UEX
T2GC
ELL
MOD
UEX
T2GC
ELL

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T

Meaning: It is set according to the topographic feature.For


details about this parameter, see 3GPP TS 25.331. This
parameter is used for the inter-RAT handover decision in
combination with the neighboring cell oriented CIO. The larger
the sum, the higher the handover priority of the GSM cell. The
smaller the sum, the lower the handover priority of the GSM
cell. The parameter is generally set to 0.
GUI Value Range: -50~50
Unit: dB
Actual Value Range: -50~50
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

05 Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
InterR
ATNC
ovHO
CSTh
d

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han

Meaning: Quality requirement for the cell of another RAT during


inter-RAT CS handovers. If the quality of the target frequency is
higher than this threshold, event 3C is triggered. Value 0
indicates the value of this parameter is smaller than -110 dBm.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 21

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

dov
er
Bas
ed
on
Loa
d
InterR
ATNC
ovHO
CSTh
d

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Meaning: Quality requirement for the cell of another RAT during


inter-RAT CS handovers. If the quality of the target frequency is
higher than this threshold, event 3C is triggered. Value 0
indicates the value of this parameter is smaller than -110 dBm.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 21

InterR
ATNC
ovHO
PSThd

B
S
C
6
9
0

ADD
UCE
LLIN
TERR
ATH
ONC

W
RF
D02
03
05

Inte
rRA
T
Han
dov

Meaning: Quality requirement for the cell of another RAT during


inter-RAT PS handovers. This parameter is used for
measurement control on event 3C. If the quality of the target
frequency is higher than this threshold, event 3C is triggered.
Value 0 indicates the value of this parameter is smaller than -110
dBm.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

InterR
ATNC
ovHO
PSThd

Description

0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
06

er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

GUI Value Range: 0~63


Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 21

B
S
C
6
9
1
0

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas

Meaning: Quality requirement for the cell of another RAT during


inter-RAT PS handovers. This parameter is used for
measurement control on event 3C. If the quality of the target
frequency is higher than this threshold, event 3C is triggered.
Value 0 indicates the value of this parameter is smaller than -110
dBm.
GUI Value Range: 0~63
Unit: dBm
Actual Value Range: -110~-48(Actual value meets the condition:
Actual Value = GUI Value - 111)
Default Value: 21

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ed
on
Loa
d
Hystfo B ADD
r3C
S UCE
C LLIN
6 TERR
9 ATH
0 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Meaning: Hysteresis for event 3C.


GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Hystfo B ADD
r3C
S UCE
C LLIN
6 TERR
9 ATH
1 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06
W
RF
D02
04
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Me
asur
eme
nt
Bas
ed
Dir
ect
Retr
y

Meaning: Hysteresis for event 3C.


GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 0

InterR
ATHO
Attem
pts

W
RF
D02

Inte
rRA
T

Meaning: Maximum number of inter-RAT handover attempts


after the non-coverage-based handover failures. For each
handover attempt, a new target cell where the UE has not been
handed over to and fulfills the criterion can be selected.

B
S
C
6

ADD
UCE
LLIN
TERR

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

InterR
ATHO
Attem
pts

Description

9 ATH
0 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

03
05
W
RF
D02
03
06

Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

GUI Value Range: 1~16


Unit: None
Actual Value Range: 1~16
Default Value: 16

B
S
C
6
9
1
0

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov

Meaning: Maximum number of inter-RAT handover attempts


after the non-coverage-based handover failures. For each
handover attempt, a new target cell where the UE has not been
handed over to and fulfills the criterion can be selected.
GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16
Default Value: 16

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Bas
ed
on
Loa
d
CSSer
viceH
OSwit
ch

B
S
C
6
9
0
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D07
00
07
W
RF
D02
03
05

GS
M
and
UM
TS
Traf
fic
Stee
ring
Bas
ed
on
Iurg
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice

Meaning: Whether the cell allows inter-RAT handover for only


CS services. When the switch is set to ON, the inter-RAT
handover for CS services is enabled. When the switch is set to
OFF, the inter-RAT handover for CS services is disabled. Based
on the Service Handover Indicator of a service and the related
parameter configurations on the network side, related
measurements and inter-RAT handover are triggered
immediately once a service is set up. For hybrid services, the
service handover is not triggered.
GUI Value Range: ON, OFF
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

CSSer
viceH
OSwit
ch

B
S
C
6
9

ADD
UCE
LLH
OCO
MM

W
RF
D07
00

GS
M
and
UM
TS

Meaning: Whether the cell allows inter-RAT handover for only


CS services. When the switch is set to ON, the inter-RAT
handover for CS services is enabled. When the switch is set to
OFF, the inter-RAT handover for CS services is disabled. Based
on the Service Handover Indicator of a service and the related

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

PSSer
viceH
OSwit
ch

Description

1 MOD 07
0 UCE W
LLH RF
OCO DMM 02
03
05

Traf
fic
Stee
ring
Bas
ed
on
Iurg
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice

parameter configurations on the network side, related


measurements and inter-RAT handover are triggered
immediately once a service is set up. For hybrid services, the
service handover is not triggered.
GUI Value Range: ON, OFF
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

B
S
C
6
9
0
0

GS
M
and
UM
TS
Traf
fic
Stee
ring
Bas
ed
on
Iurg
Inte
rRA

Meaning: Whether the cell allows inter-RAT handover for only


PS services. When the switch is set to ON, the inter-RAT
handover for PS services is enabled. When the switch is set to
OFF, the inter-RAT handover for PS services is disabled. Based
on the Service Handover Indicator of a service and the related
parameter configurations on the network side, related
measurements and inter-RAT handover are triggered
immediately once a service is set up. For hybrid services, the
service handover is not triggered.
GUI Value Range: ON, OFF
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D07
00
07
W
RF
D02
03
05

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

T
Han
dov
er
Bas
ed
on
Ser
vice
PSSer
viceH
OSwit
ch

B
S
C
6
9
1
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D07
00
07
W
RF
D02
03
05

GS
M
and
UM
TS
Traf
fic
Stee
ring
Bas
ed
on
Iurg
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice

Meaning: Whether the cell allows inter-RAT handover for only


PS services. When the switch is set to ON, the inter-RAT
handover for PS services is enabled. When the switch is set to
OFF, the inter-RAT handover for PS services is disabled. Based
on the Service Handover Indicator of a service and the related
parameter configurations on the network side, related
measurements and inter-RAT handover are triggered
immediately once a service is set up. For hybrid services, the
service handover is not triggered.
GUI Value Range: ON, OFF
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

SndLd B SET W Inte Meaning: Switch for sending load information to the GSM
Info2 S UINT RF rnetwork. This parameter is designed for the UMTS load-based

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

GsmIn C ERR
d
6 ATH
9 ONC
0 OV
0

D02
03
05
W
RF
D02
03
06

RA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

access control strategy when the 3G-to-2G handover is required.


When the UE is handed over from the UMTS network to the
GSM network, the RNC obtains the load information of the best
cell and sends it to the GSM network. This parameter is valid
only for CS service. The RNC does not send UMTS cell load
information to the GSM in PS domain.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: ON

SndLd
Info2
GsmIn
d

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T

Meaning: Switch for sending load information to the GSM


network. This parameter is designed for the UMTS load-based
access control strategy when the 3G-to-2G handover is required.
When the UE is handed over from the UMTS network to the
GSM network, the RNC obtains the load information of the best
cell and sends it to the GSM network. This parameter is valid
only for CS service. The RNC does not send UMTS cell load
information to the GSM in PS domain.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: ON

B
S
C
6
9
1
0

SET
UINT
ERR
ATH
ONC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Han
dov
er
Bas
ed
on
Loa
d
Ncov
HoOn
2GldI
nd

B
S
C
6
9
0
0

SET
UINT
ERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Meaning: Threshold for 2G load for outgoing inter-RAT PS


handovers. This parameter specifies the threshold for 2G load for
outgoing inter-RAT PS handovers. If the GSM load policy is
used, that is, "NcovHoOn2GldInd" in the "SET
UINTERRATHONCOV" command is set to ON, a noncoverage-based handover from the 3G cell to the 2G cell is
stopped if the uplink or downlink normalized load carried in the
relocation response message from the 2G network exceeds the
value of this parameter.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: ON

Ncov
HoOn
2GldI
nd

B
S
C
6
9

SET
UINT
ERR
ATH
ONC

W
RF
D02
03

Inte
rRA
T
Han

Meaning: Threshold for 2G load for outgoing inter-RAT PS


handovers. This parameter specifies the threshold for 2G load for
outgoing inter-RAT PS handovers. If the GSM load policy is
used, that is, "NcovHoOn2GldInd" in the "SET
UINTERRATHONCOV" command is set to ON, a non-

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

CSHO
Out2G
loadT
hd

Description

1 OV
0

05
W
RF
D02
03
06

dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

coverage-based handover from the 3G cell to the 2G cell is


stopped if the uplink or downlink normalized load carried in the
relocation response message from the 2G network exceeds the
value of this parameter.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: ON

B
S
C
6
9
0
0

W
RF
D07
00
04
W
RF
D02
03
10
W
RF
D02
03
05
W

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er

Meaning: Threshold for 2G load for outgoing inter-RAT CS


handovers. If the GSM load policy is used, that is,
"NcovHoOn2GldInd" in the "SET UINTERRATHONCOV"
command is set to ON, a non-coverage-based handover from the
3G cell to the 2G cell is stopped if the uplink or downlink
normalized load carried in the relocation response message from
the 2G network exceeds the value of this parameter.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 80

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D02
03
06

Bas
ed
on
Loa
d

Description

CSHO
Out2G
loadT
hd

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D07
00
04
W
RF
D02
03
10
W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Meaning: Threshold for 2G load for outgoing inter-RAT CS


handovers. If the GSM load policy is used, that is,
"NcovHoOn2GldInd" in the "SET UINTERRATHONCOV"
command is set to ON, a non-coverage-based handover from the
3G cell to the 2G cell is stopped if the uplink or downlink
normalized load carried in the relocation response message from
the 2G network exceeds the value of this parameter.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 80

PSHO
Out2G
loadT
hd

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD

W
RF
D07
00
04
W
RF

Inte
rRA
T
Han
dov
er
Bas

Meaning: Threshold for 2G load for outgoing inter-RAT PS


handovers. This parameter specifies the threshold for 2G load for
outgoing inter-RAT PS handovers. If the GSM load policy is
used, that is, "NcovHoOn2GldInd" in the "SET
UINTERRATHONCOV" command is set to ON, a noncoverage-based handover from the 3G cell to the 2G cell is
stopped if the uplink or downlink normalized load carried in the
relocation response message from the 2G network exceeds the

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

PSHO
Out2G
loadT
hd

B
S
C
6
9
1
0

Description

UCE
LLIN
TERR
ATH
ONC
OV

D02
03
10
W
RF
D02
03
05
W
RF
D02
03
06

ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

value of this parameter.


GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 60

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D07
00
04
W
RF
D02
03
10
W
RF
D02
03
05
W
RF
D02

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on

Meaning: Threshold for 2G load for outgoing inter-RAT PS


handovers. This parameter specifies the threshold for 2G load for
outgoing inter-RAT PS handovers. If the GSM load policy is
used, that is, "NcovHoOn2GldInd" in the "SET
UINTERRATHONCOV" command is set to ON, a noncoverage-based handover from the 3G cell to the 2G cell is
stopped if the uplink or downlink normalized load carried in the
relocation response message from the 2G network exceeds the
value of this parameter.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 60

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

03 Loa
06 d
HspaT B SET
imerL S UHO
en
C COM
6 M
9
0
0

W
RF
D01
06
10
06
W
RF
D01
06
12
04

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt

Meaning: Length of the HSPA serving cell change penalty timer.


This timer shall be started after the HSPA serving cell is
changed. No more serving cell change shall be performed until
the timer expires. The value 0 means this timer shall not be
started and serving cell change be initiated immediately.
GUI Value Range: 0~1024
Unit: s
Actual Value Range: 0~1024
Default Value: 0

HspaT B SET
imerL S UHO
en
C COM
6 M
9
1
0

W
RF
D01
06
10
06
W
RF
D01
06
12
04

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
HS
UP
A
Mo
bilit

Meaning: Length of the HSPA serving cell change penalty timer.


This timer shall be started after the HSPA serving cell is
changed. No more serving cell change shall be performed until
the timer expires. The value 0 means this timer shall not be
started and serving cell change be initiated immediately.
GUI Value Range: 0~1024
Unit: s
Actual Value Range: 0~1024
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

y
Ma
nag
eme
nt
NBM
Machs
Reset
AlgoS
elSwit
ch

B
S
C
6
9
0
0

ADD
UCE
LLAL
GOS
WITC
H
MOD
UCE
LLAL
GOS
WITC
H

W
RF
D01
06
10
06

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt

Meaning: The algorithms with the above values represent are as


follow: ALGORITHM_REQUIRED: Always reset the mac-hs no
matter the cells in question are in the same NodeB or not.
ALGORITHM_DEPEND_ON_LCG: Reset the mac-hs only
when the cells in question are in the different local cell group.
GUI Value Range: ALGORITHM_REQUIRED,
ALGORITHM_DEPEND_ON_LCG
Unit: None
Actual Value Range: ALGORITHM_REQUIRED,
ALGORITHM_DEPEND_ON_LCG
Default Value: ALGORITHM_DEPEND_ON_LCG

NBM
Machs
Reset
AlgoS
elSwit
ch

B
S
C
6
9
1
0

ADD
UCE
LLAL
GOS
WITC
H
MOD
UCE
LLAL
GOS
WITC
H

W
RF
D01
06
10
06

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt

Meaning: The algorithms with the above values represent are as


follow: ALGORITHM_REQUIRED: Always reset the mac-hs no
matter the cells in question are in the same NodeB or not.
ALGORITHM_DEPEND_ON_LCG: Reset the mac-hs only
when the cells in question are in the different local cell group.
GUI Value Range: ALGORITHM_REQUIRED,
ALGORITHM_DEPEND_ON_LCG
Unit: None
Actual Value Range: ALGORITHM_REQUIRED,
ALGORITHM_DEPEND_ON_LCG
Default Value: ALGORITHM_DEPEND_ON_LCG

RlRstr B SET
Tmr
S USTA
C TETI
6 MER
9
0
0

W
RF
D01
01
01
W

3G
PP
R9
Spe
cifi
cati
ons

Meaning: A timer to RNC wait for radio link restoration


indication in the radio link procedure. Note: The value range of
"RlRstrTmr" is 1 to 300000 in the current version. In a later
version, the value range changes into 100 to 300000. In the
current version, if you enter a value within the range of 1 to 100
including 1, this value can still be synchronized and issued but
the system regards the value as 11000, the recommended value.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RF
D14
01
03

Call
Ree
stab
lish
men
t

Therefore, you are advised not to enter a value smaller than 100.
Disuse Statement:The value range of "RlRstrTmr" is 1 to 300000
in the current version. In a later version, the value range changes
into 100 to 300000. In the current version, if you enter a value
within the range of 1 to 100 including 1, this value can still be
synchronized and issued but the system regards the value as
11000, the recommended value. Therefore, you are advised not
to enter a value smaller than 100.
GUI Value Range: 1~300000
Unit: ms
Actual Value Range: 1~300000
Default Value: 11000

RlRstr B SET
Tmr
S USTA
C TETI
6 MER
9
1
0

W
RF
D01
01
01
W
RF
D14
01
03

3G
PP
R9
Spe
cifi
cati
ons
Call
Ree
stab
lish
men
t

Meaning: A timer to RNC wait for radio link restoration


indication in the radio link procedure. Note: The value range of
"RlRstrTmr" is 1 to 300000 in the current version. In a later
version, the value range changes into 100 to 300000. In the
current version, if you enter a value within the range of 1 to 100
including 1, this value can still be synchronized and issued but
the system regards the value as 11000, the recommended value.
Therefore, you are advised not to enter a value smaller than 100.
Disuse Statement:The value range of "RlRstrTmr" is 1 to 300000
in the current version. In a later version, the value range changes
into 100 to 300000. In the current version, if you enter a value
within the range of 1 to 100 including 1, this value can still be
synchronized and issued but the system regards the value as
11000, the recommended value. Therefore, you are advised not
to enter a value smaller than 100.
GUI Value Range: 1~300000
Unit: ms
Actual Value Range: 1~300000
Default Value: 11000

MaxE
dchCe
llInAc
tiveSe
t

W
RF
D01
06

HS
UP
A
Mo
bilit

Meaning: This parameter determines the maximum number of


links in the EDCH active set. When the RNC acts as the SRNC,
the number of links in the EDCH active set for all the UEs under
the RNC cannot exceed the parameter value. If the parameter
value is too large, a lot of resources on the RAN side will be

B
S
C
6
9

SET
UHO
COM
M

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0
0

Description

12 y
04 Ma
nag
eme
nt

occupied as the same data is transferred over multiple EDCH


links in macro diversity, thus affecting the system performance.
If this parameter value is too small, insufficient combination gain
can be achieved in macro diversity by the EDCH, which causes
excessive retransmissions and affects the UE speed.
GUI Value Range: 1~4
Unit: None
Actual Value Range: 1~4
Default Value: 3

MaxE
dchCe
llInAc
tiveSe
t

B
S
C
6
9
1
0

SET
UHO
COM
M

W
RF
D01
06
12
04

HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt

Meaning: This parameter determines the maximum number of


links in the EDCH active set. When the RNC acts as the SRNC,
the number of links in the EDCH active set for all the UEs under
the RNC cannot exceed the parameter value. If the parameter
value is too large, a lot of resources on the RAN side will be
occupied as the same data is transferred over multiple EDCH
links in macro diversity, thus affecting the system performance.
If this parameter value is too small, insufficient combination gain
can be achieved in macro diversity by the EDCH, which causes
excessive retransmissions and affects the UE speed.
GUI Value Range: 1~4
Unit: None
Actual Value Range: 1~4
Default Value: 3

CSVoi
ceOve
rHspa
SuppI
nd

B
S
C
6
9
0
0

ADD
UNR
NC
MOD
UNR
NC

W
RF
D01
06
10
19

HS
DP
A
Dyn
ami
c
Po
wer
All
ocat
ion

Meaning: Indicates whether degrade HSPA to DCH procedure is


performed before the relocation procedure when the CS services
are carried on the HSPA. If this parameter is set to OFF, the
HSPA needs to be degraded to the DCH before the relocation
procedure. If this parameter is set to ON, the HSPA need not be
degraded to the DCH before the relocation procedure.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

CSVoi B ADD

W HS

Meaning: Indicates whether degrade HSPA to DCH procedure is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
ceOve
rHspa
SuppI
nd

S
C
6
9
1
0

Description

UNR
NC
MOD
UNR
NC

RF
D01
06
10
19

DP
A
Dyn
ami
c
Po
wer
All
ocat
ion

performed before the relocation procedure when the CS services


are carried on the HSPA. If this parameter is set to OFF, the
HSPA needs to be degraded to the DCH before the relocation
procedure. If this parameter is set to ON, the HSPA need not be
degraded to the DCH before the relocation procedure.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

HystF B ADD
or1J
S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the hysteretic value for event


1J. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

HystF B ADD
or1J
S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ

W
RF
D02
02
03
W
RF
D02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN

Meaning: This parameter specifies the hysteretic value for event


1J. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331.In addition, filter coefficient and
interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
HO

Description

02 C
Soft
Han
dov
er

TrigTi B ADD
me1J S UCE
C LLIN
6 TRAF
9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: This parameter specifies the interval time between


detection of event 1J and sending of the measurement report. The
value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

TrigTi B ADD
me1J S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft

Meaning: This parameter specifies the interval time between


detection of event 1J and sending of the measurement report. The
value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Han GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
dov D160, D200, D240, D320, D640, D1280, D2560, D5000
er
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640
Period
MRRe
portN
umfor
1J

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Number of times event 1J is reported after the


reporting mode is changed to periodic reporting. When the
number of times event 1J is reported exceeds this parameter
value, periodic reporting of event 1J is disabled.
GUI Value Range: D1, D2, D4, D8, D16, D32, D64, INFINITY
Unit: None
Actual Value Range: 1, 2, 4, 8, 16, 32, 64, INFINITY
Default Value: D64

Period
MRRe
portN
umfor
1J

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov

Meaning: Number of times event 1J is reported after the


reporting mode is changed to periodic reporting. When the
number of times event 1J is reported exceeds this parameter
value, periodic reporting of event 1J is disabled.
GUI Value Range: D1, D2, D4, D8, D16, D32, D64, INFINITY
Unit: None
Actual Value Range: 1, 2, 4, 8, 16, 32, 64, INFINITY
Default Value: D64

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Report
Interv
alfor1
J

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Interval at which event 1J is reported after the


reporting mode is changed to periodical reporting. Generally,
event 1J is reported only once. To avoid the loss of measurement
reports, the UE set the mode of reporting event 1J to periodical if
the cell reporting event 1J is not added to the DCH active set in a
specified period of time. Event 1J is reported for
"PeriodMRReportNumfor1J" times at the interval specified by
this parameter.If the mode of reporting event 1J is set to
"NON_PERIODIC_REPORT", the UE cannot change the event
1J reporting mode to periodical.
GUI Value Range: NON_PERIODIC_REPORT, D250, D500,
D1000, D2000, D4000, D8000, D16000
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 4000, 8000, 16000
Default Value: D1000

Report
Interv
alfor1
J

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Interval at which event 1J is reported after the


reporting mode is changed to periodical reporting. Generally,
event 1J is reported only once. To avoid the loss of measurement
reports, the UE set the mode of reporting event 1J to periodical if
the cell reporting event 1J is not added to the DCH active set in a
specified period of time. Event 1J is reported for
"PeriodMRReportNumfor1J" times at the interval specified by
this parameter.If the mode of reporting event 1J is set to
"NON_PERIODIC_REPORT", the UE cannot change the event
1J reporting mode to periodical.
GUI Value Range: NON_PERIODIC_REPORT, D250, D500,
D1000, D2000, D4000, D8000, D16000
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 4000, 8000, 16000
Default Value: D1000

CellC B ADD
apCon S UEX

W Inte Meaning: 1)DELAY_ACTIVATION_SUPPORT (delay


RF r
activation support indicator):when the indicator is TRUE, it

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
tainer
Fdd

C
6
9
0
0

T3GC
ELL
MOD
UEX
T3GC
ELL

D02
02
03
W
RF
D02
14
00

RN
C
Soft
Han
dov
er
Dir
ect
Sig
nali
ng
Con
nect
ion
Reesta
blis
hme
nt
(DS
CR)

Description

means that the cell support delay activation. Delayed Activation


IE indicates that the activation of the DL power shall be delayed
until an indicated CFN or until a separate activation indication is
received. 2)HSDSCH_SUPPORT(HSDSCH support
indicator):when the indicator is TRUE, it means that the cell
support HSDSCH and enable downlink traffic to be established
in HSDSCH. 3)FDPCH_SUPPORT(F-DPCH support
indicator):when the indicator is TRUE, it means that the cell
support F-DPCH and enable downlink signal to be established in
F-DPCH, but the cell can not support F-DPCH if it does not
support HSDSCH. 4)EDCH_SUPPORT(E-DCH support
indicator):when the indicator is TRUE, it means that the cell
support E-DCH and enable uplink signal and traffic to be
established in E-DCH.. 5)EDCH_2MS_TTI_SUPPORT(E-DCH
2ms TTI support indicator):when the indicator is TRUE, it
means that the cell support E-DCH 2ms TTI.
6)EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH max SF
support 2SF2+2SF4 indicator):when the indicator is TRUE, it
means that the cell has E-DCH SF capability of 2SF2+2SF4.
7)EDCH_2SF2_SUPPORT(E-DCH max SF support 2SF
indicator):when the indicator is TRUE, it means that the cell has
E-DCH SF capability of 2SF2. 8)EDCH_2SF4_SUPPORT(EDCH max SF support 2SF4 indicator):when the indicator is
TRUE, it means that the cell has E-DCH SF capability of 2SF4.
9)EDCH_SF4_SUPPORT(E-DCH max SF support SF4
indicator):when the indicator is TRUE, it means that the cell has
E-DCH SF capability of SF4. 10)EDCH_SF8_SUPPORT(EDCH max SF support SF8 indicator):when the indicator is
TRUE, it means that the cell has E-DCH SF capability of SF8.
11)EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCH support
HARQ IR Combining indicator):when the indicator is TRUE, it
means that the cell use IR combine Mode when MAC-e PDUs
are received more than one time in E-DCH.
12)EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH
support HARQ CHASE Combining indicator): when the
indicator is TRUE, it means that the cell use CHASE combine
Mode when MAC-e PDUs are received more than one time in EDCH. 13)CPC_DTX_DRX_SUPPORT(CPC DTX-DRX support
indicator): when the indicator is TRUE, it indicates that the cell

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

supports CPC DTX_DRX.


14)CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH
less operation support indicator): when the indicator is TRUE, it
indicates that the cell supports CPC HS-SCCH less operation.
15)HSPAPLUS_MIMO_SUPPORT(MIMO support indicator):
when the indicator is TRUE, it indicates that the cell supports
MIMO. 16)FLEX_MACD_PDU_SIZE_SUPPORT(flexible
MAC-d PDU Size support indicator): when the indicator is
TRUE, it indicates that the cell supports flexible MAC-d PDU
Size. 17)FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slot
format support indicator): when the indicator is TRUE, it
indicates that the cell supports F-DPCH slot format, which
depends on FDPCH. If F-DPCH slot format is set to support in
the cell, it should support FDPCH too.when the indicator is
TRUE, the indicator FDPCH_SUPPORT shoud be set true.
18)HSPAPLUS_DL_64QAM_SUPPORT(downlink 64QAM
support indicator): when the indicator is TRUE, it indicates that
the cell supports downlink 64QAM.
GUI Value Range: DELAY_ACTIVATION_SUPPORT(delay
activation support indication), HSDSCH_SUPPORT(HSDSCH
support indication), FDPCH_SUPPORT(F-DPCH support
indication), EDCH_SUPPORT(E-DCH support indication),
EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTI support
indicator), EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH max
SF support 2SF2+2SF4 indicator), EDCH_2SF2_SUPPORT(EDCH max SF support 2SF2 indicator),
EDCH_2SF4_SUPPORT(E-DCH max SF support 2SF4
indicator), EDCH_SF4_SUPPORT(E-DCH max SF support SF4
indicator), EDCH_SF8_SUPPORT(E-DCH max SF support SF8
indicator), EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCH
support HARQ IR Combining indicator),
EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support
HARQ CHASE Combining indicator),
CPC_DTX_DRX_SUPPORT(CPC DTX-DRX support
indicator), CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HSSCCH less operation support indicator),
HSPAPLUS_MIMO_SUPPORT(MIMO support indicator),
FLEX_MACD_PDU_SIZE_SUPPORT(flexible MAC-d PDU
Size support indicator),

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slot format


support indicator),
HSPAPLUS_DL_64QAM_SUPPORT(downlink 64QAM
support indicator)
Unit: None
Actual Value Range: DELAY_ACTIVATION_SUPPORT,
HSDSCH_SUPPORT, FDPCH_SUPPORT, EDCH_SUPPORT,
EDCH_2MS_TTI_SUPPORT,
EDCH_2SF2_AND_2SF4_SUPPORT,
EDCH_2SF2_SUPPORT, EDCH_2SF4_SUPPORT,
EDCH_SF4_SUPPORT, EDCH_SF8_SUPPORT,
EDCH_HARQ_IR_COMBIN_SUPPORT,
EDCH_HARQ_CHASE_COMBIN_SUPPORT,
CPC_DTX_DRX_SUPPORT,
CPC_HS_SCCH_LESS_OPER_SUPPORT,
HSPAPLUS_MIMO_SUPPORT,
FLEX_MACD_PDU_SIZE_SUPPORT,
FDPCH_SLOT_FORMAT_SUPPORT,
HSPAPLUS_DL_64QAM_SUPPORT
Default Value: None
CellC
apCon
tainer
Fdd

B
S
C
6
9
1
0

ADD
UEX
T3GC
ELL
MOD
UEX
T3GC
ELL

W
RF
D02
02
03
W
RF
D02
14
00

Inte
r
RN
C
Soft
Han
dov
er
Dir
ect
Sig
nali
ng
Con
nect
ion
Reesta

Meaning: 1)DELAY_ACTIVATION_SUPPORT (delay


activation support indicator):when the indicator is TRUE, it
means that the cell support delay activation. Delayed Activation
IE indicates that the activation of the DL power shall be delayed
until an indicated CFN or until a separate activation indication is
received. 2)HSDSCH_SUPPORT(HSDSCH support
indicator):when the indicator is TRUE, it means that the cell
support HSDSCH and enable downlink traffic to be established
in HSDSCH. 3)FDPCH_SUPPORT(F-DPCH support
indicator):when the indicator is TRUE, it means that the cell
support F-DPCH and enable downlink signal to be established in
F-DPCH, but the cell can not support F-DPCH if it does not
support HSDSCH. 4)EDCH_SUPPORT(E-DCH support
indicator):when the indicator is TRUE, it means that the cell
support E-DCH and enable uplink signal and traffic to be
established in E-DCH.. 5)EDCH_2MS_TTI_SUPPORT(E-DCH
2ms TTI support indicator):when the indicator is TRUE, it
means that the cell support E-DCH 2ms TTI.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
blis
hme
nt
(DS
CR)

Description

6)EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH max SF
support 2SF2+2SF4 indicator):when the indicator is TRUE, it
means that the cell has E-DCH SF capability of 2SF2+2SF4.
7)EDCH_2SF2_SUPPORT(E-DCH max SF support 2SF
indicator):when the indicator is TRUE, it means that the cell has
E-DCH SF capability of 2SF2. 8)EDCH_2SF4_SUPPORT(EDCH max SF support 2SF4 indicator):when the indicator is
TRUE, it means that the cell has E-DCH SF capability of 2SF4.
9)EDCH_SF4_SUPPORT(E-DCH max SF support SF4
indicator):when the indicator is TRUE, it means that the cell has
E-DCH SF capability of SF4. 10)EDCH_SF8_SUPPORT(EDCH max SF support SF8 indicator):when the indicator is
TRUE, it means that the cell has E-DCH SF capability of SF8.
11)EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCH support
HARQ IR Combining indicator):when the indicator is TRUE, it
means that the cell use IR combine Mode when MAC-e PDUs
are received more than one time in E-DCH.
12)EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH
support HARQ CHASE Combining indicator): when the
indicator is TRUE, it means that the cell use CHASE combine
Mode when MAC-e PDUs are received more than one time in EDCH. 13)CPC_DTX_DRX_SUPPORT(CPC DTX-DRX support
indicator): when the indicator is TRUE, it indicates that the cell
supports CPC DTX_DRX.
14)CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH
less operation support indicator): when the indicator is TRUE, it
indicates that the cell supports CPC HS-SCCH less operation.
15)HSPAPLUS_MIMO_SUPPORT(MIMO support indicator):
when the indicator is TRUE, it indicates that the cell supports
MIMO. 16)FLEX_MACD_PDU_SIZE_SUPPORT(flexible
MAC-d PDU Size support indicator): when the indicator is
TRUE, it indicates that the cell supports flexible MAC-d PDU
Size. 17)FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slot
format support indicator): when the indicator is TRUE, it
indicates that the cell supports F-DPCH slot format, which
depends on FDPCH. If F-DPCH slot format is set to support in
the cell, it should support FDPCH too.when the indicator is
TRUE, the indicator FDPCH_SUPPORT shoud be set true.
18)HSPAPLUS_DL_64QAM_SUPPORT(downlink 64QAM

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

support indicator): when the indicator is TRUE, it indicates that


the cell supports downlink 64QAM.
GUI Value Range: DELAY_ACTIVATION_SUPPORT(delay
activation support indication), HSDSCH_SUPPORT(HSDSCH
support indication), FDPCH_SUPPORT(F-DPCH support
indication), EDCH_SUPPORT(E-DCH support indication),
EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTI support
indicator), EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH max
SF support 2SF2+2SF4 indicator), EDCH_2SF2_SUPPORT(EDCH max SF support 2SF2 indicator),
EDCH_2SF4_SUPPORT(E-DCH max SF support 2SF4
indicator), EDCH_SF4_SUPPORT(E-DCH max SF support SF4
indicator), EDCH_SF8_SUPPORT(E-DCH max SF support SF8
indicator), EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCH
support HARQ IR Combining indicator),
EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support
HARQ CHASE Combining indicator),
CPC_DTX_DRX_SUPPORT(CPC DTX-DRX support
indicator), CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HSSCCH less operation support indicator),
HSPAPLUS_MIMO_SUPPORT(MIMO support indicator),
FLEX_MACD_PDU_SIZE_SUPPORT(flexible MAC-d PDU
Size support indicator),
FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slot format
support indicator),
HSPAPLUS_DL_64QAM_SUPPORT(downlink 64QAM
support indicator)
Unit: None
Actual Value Range: DELAY_ACTIVATION_SUPPORT,
HSDSCH_SUPPORT, FDPCH_SUPPORT, EDCH_SUPPORT,
EDCH_2MS_TTI_SUPPORT,
EDCH_2SF2_AND_2SF4_SUPPORT,
EDCH_2SF2_SUPPORT, EDCH_2SF4_SUPPORT,
EDCH_SF4_SUPPORT, EDCH_SF8_SUPPORT,
EDCH_HARQ_IR_COMBIN_SUPPORT,
EDCH_HARQ_CHASE_COMBIN_SUPPORT,
CPC_DTX_DRX_SUPPORT,
CPC_HS_SCCH_LESS_OPER_SUPPORT,
HSPAPLUS_MIMO_SUPPORT,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

FLEX_MACD_PDU_SIZE_SUPPORT,
FDPCH_SLOT_FORMAT_SUPPORT,
HSPAPLUS_DL_64QAM_SUPPORT
Default Value: None
Chann
elRetr
yHoTi
merLe
n

B
S
C
6
9
0
0

SET
UCOI
FTIM
ER

W
RF
D01
06
14
03
W
RF
D02
11
01
W
RF
D01
06
85
W
RF
D01
06
52
W
RF
D01
06
86
W
RF

HS
UP
A
2ms
TTI
Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
Do
wnl
ink
Enh
anc
ed
L2
SR
B
ove
r
HS
DP
A
CP
C-

Meaning: This parameter specifies the value of the channel retry


handover timer. When handover is performed and some higher
HSPA or HSPA plus technique is supported, UTRAN will trigger
the reconfiguration for the higher techniques. Pingpang will
happen when the reconfiguration is triggered immediately when
handover succeeds, because handover procedure is frequently. In
order to avoid the pingpang, this timer will start after handover
procedure is performed, and the reconfiguration will not be
triggered until the timer expires.
GUI Value Range: 0~999
Unit: s
Actual Value Range: 0~999
Default Value: 2

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D01
06
87
W
RF
D01
06
84
W
RF
D01
06
14
04
W
RF
D01
06
83
W
RF
D15
02
09
W
RF
D01
06
36
W
RF
D-

DT
X/
DR
X
CP
CHSSC
CH
less
ope
rati
on
2x2
MI
MO
HS
UP
A
2ms
/10
ms
TTI
Han
dov
er
Do
wnl
ink
64Q
AM
DBHS
DP
A
SR
B
ove

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

02 r
12 HS
00 UP
A
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Chann
elRetr
yHoTi
merLe
n

B
S
C
6
9
1
0

SET
UCOI
FTIM
ER

W
RF
D01
06
14
03
W
RF
D02
11
01
W
RF
D01
06
85
W
RF
D01
06

HS
UP
A
2ms
TTI
Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
Do
wnl
ink
Enh
anc
ed

Meaning: This parameter specifies the value of the channel retry


handover timer. When handover is performed and some higher
HSPA or HSPA plus technique is supported, UTRAN will trigger
the reconfiguration for the higher techniques. Pingpang will
happen when the reconfiguration is triggered immediately when
handover succeeds, because handover procedure is frequently. In
order to avoid the pingpang, this timer will start after handover
procedure is performed, and the reconfiguration will not be
triggered until the timer expires.
GUI Value Range: 0~999
Unit: s
Actual Value Range: 0~999
Default Value: 2

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
52
W
RF
D01
06
86
W
RF
D01
06
87
W
RF
D01
06
84
W
RF
D01
06
14
04
W
RF
D01
06
83
W
RF
D15
02
09

L2
SR
B
ove
r
HS
DP
A
CP
CDT
X/
DR
X
CP
CHSSC
CH
less
ope
rati
on
2x2
MI
MO
HS
UP
A
2ms
/10
ms
TTI
Han
dov
er
Do
wnl

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Chann
elRetr
yTime
rLen

B
S
C
6
9
0
0

SET
UCOI
FTIM
ER

W
RF
D01
06
36
W
RF
D02
12
00

ink
64Q
AM
DBHS
DP
A
SR
B
ove
r
HS
UP
A
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

W
RF
D01
06
14
03
W
RF
D02
11
01
W

HS
UP
A
2ms
TTI
Dyn
ami
c
Cha
nnel
Con
figu
rati
on

Description

Meaning: This parameter specifies the value of the channel retry


timer. The timer will start when traffic is set up or reconfigured
and some higher technique is not configured by some reason
except for the capability of UE or cell. Channel retry will be
performed after this timer expires.
GUI Value Range: 0~180
Unit: s
Actual Value Range: 0~180
Default Value: 5

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D01
06
94
W
RF
D01
06
93
W
RF
D15
02
07
W
RF
D01
06
52
W
RF
D01
06
86
W
RF
D01
06
87
W
RF
D-

Con
trol
(DC
CC)
UL
16Q
AM
DL
64Q
AM
+M
IM
O
4CHS
DP
A
SR
B
ove
r
HS
DP
A
CP
CDT
X/
DR
X
CP
CHSSC
CH
less
ope
rati

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
01
06
84
W
RF
D01
06
85
W
RF
D01
06
83
W
RF
D01
06
10
08
W
RF
D15
02
09
W
RF
D01
06
12
06
W
RF
D-

on
2x2
MI
MO
Do
wnl
ink
Enh
anc
ed
L2
Do
wnl
ink
64Q
AM
Inte
ract
ive
and
Bac
kgr
oun
d
Traf
fic
Cla
ss
on
HS
DP
A
DBHS
DP
A
Inte
ract

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
14
02
04
W
RF
D01
06
96
W
RF
D15
02
50
W
RF
D01
06
36
W
RF
D01
06
30
W
RF
D01
06
32
W
RF
D01
06

ive
and
Bac
kgr
oun
d
Traf
fic
Cla
ss
on
HS
UP
A
DCHS
UP
A
DCHS
DP
A
3CHS
DP
A
SR
B
ove
r
HS
UP
A
Stre
ami
ng
Traf
fic
Cla

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

11 ss
12 on
HS
DP
A
Stre
ami
ng
Traf
fic
Cla
ss
on
HS
UP
A
HS
DP
A
DR
D
Chann
elRetr
yTime
rLen

B
S
C
6
9
1
0

SET
UCOI
FTIM
ER

W
RF
D01
06
14
03
W
RF
D02
11
01
W
RF
D01

HS
UP
A
2ms
TTI
Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC

Meaning: This parameter specifies the value of the channel retry


timer. The timer will start when traffic is set up or reconfigured
and some higher technique is not configured by some reason
except for the capability of UE or cell. Channel retry will be
performed after this timer expires.
GUI Value Range: 0~180
Unit: s
Actual Value Range: 0~180
Default Value: 5

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
06
94
W
RF
D01
06
93
W
RF
D15
02
07
W
RF
D01
06
52
W
RF
D01
06
86
W
RF
D01
06
87
W
RF
D01
06
84

CC)
UL
16Q
AM
DL
64Q
AM
+M
IM
O
4CHS
DP
A
SR
B
ove
r
HS
DP
A
CP
CDT
X/
DR
X
CP
CHSSC
CH
less
ope
rati
on
2x2
MI

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D01
06
85
W
RF
D01
06
83
W
RF
D01
06
10
08
W
RF
D15
02
09
W
RF
D01
06
12
06
W
RF
D14
02
04

MO
Do
wnl
ink
Enh
anc
ed
L2
Do
wnl
ink
64Q
AM
Inte
ract
ive
and
Bac
kgr
oun
d
Traf
fic
Cla
ss
on
HS
DP
A
DBHS
DP
A
Inte
ract
ive
and
Bac
kgr

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
W
RF
D01
06
96
W
RF
D15
02
50
W
RF
D01
06
36
W
RF
D01
06
30
W
RF
D01
06
32
W
RF
D01
06
11
12

oun
d
Traf
fic
Cla
ss
on
HS
UP
A
DCHS
UP
A
DCHS
DP
A
3CHS
DP
A
SR
B
ove
r
HS
UP
A
Stre
ami
ng
Traf
fic
Cla
ss
on
HS
DP

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

A
Stre
ami
ng
Traf
fic
Cla
ss
on
HS
UP
A
HS
DP
A
DR
D
Retry B SET
Capab S UFR
ility
C C
6
9
0
0

W
RF
D01
06
14
03
W
RF
D01
06
99
W
RF
D15
12
09
W
RF

HS
UP
A
2ms
TTI
DCHS
DP
A+
MI
MO
Ma
croMic
ro
DCHS
DP
A
4CHS

Meaning: This parameter specifies which HSPA technologies can


be retried by UEs. When the HSPA technologies are selected and
currently UE is not using them, "RNC" will initiate these HSPA
technologies retry for UE.
GUI Value Range: SRB_OVER_HSDPA, SRB_OVER_HSUPA,
TTI_2MS, MIMO, 64QAM, DL_L2_ENHANCE, DTX_DRX,
HSSCCH_LESS_OPERATION, MIMO_64QAM, DC_HSDPA,
UL_L2_ENHANCE, UL_16QAM, EDPCCH_BOOSTING,
DCMIMO_HSDPA, DC_HSUPA, HSDPA_4C_MIMO,
HSDPA_4C, DBMIMO_HSDPA, DB_HSDPA
Unit: None
Actual Value Range: SRB_OVER_HSDPA,
SRB_OVER_HSUPA, TTI_2MS, MIMO, 64QAM,
DL_L2_ENHANCE, DTX_DRX,
HSSCCH_LESS_OPERATION, MIMO_64QAM, DC_HSDPA,
UL_L2_ENHANCE, UL_16QAM, EDPCCH_BOOSTING,
DCMIMO_HSDPA, DC_HSUPA, HSDPA_4C_MIMO,
HSDPA_4C, DBMIMO_HSDPA, DB_HSDPA
Default Value:
SRB_OVER_HSDPA:0,SRB_OVER_HSUPA:0,TTI_2MS:0,MI

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
D15
02
07
W
RF
D01
06
52
W
RF
D01
06
86
W
RF
D01
06
87
W
RF
D01
06
84
W
RF
D01
06
85
W
RF
D01

DP
A
SR
B
ove
r
HS
DP
A
CP
CDT
X/
DR
X
CP
CHSSC
CH
less
ope
rati
on
2x2
MI
MO
Do
wnl
ink
Enh
anc
ed
L2
UL
Lay
er 2
Imp

Description

MO:1,64QAM:1,DL_L2_ENHANCE:1,DTX_DRX:1,HSSCCH
_LESS_OPERATION:1,MIMO_64QAM:0,DC_HSDPA:0,UL_L
2_ENHANCE:0,UL_16QAM:0,EDPCCH_BOOSTING:0,DCMI
MO_HSDPA:0,DC_HSUPA:0,HSDPA_4C_MIMO:0,HSDPA_4
C:0,DBMIMO_HSDPA:0,DB_HSDPA:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
06
95
W
RF
D01
06
83
W
RF
D01
06
97
W
RF
D01
06
94
W
RF
D15
02
27
W
RF
D15
02
09
W
RF
D15
02
50

rov
eme
nt
Do
wnl
ink
64Q
AM
EDP
CC
H
Boo
stin
g
UL
16Q
AM
DBHS
DP
A+
MI
MO
DBHS
DP
A
3CHS
DP
A
SR
B
ove
r
HS
UP

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Retry B SET
Capab S UFR
ility
C C
6
9
1
0

W
RF
D01
06
36
W
RF
D01
06
96
W
RF
D15
02
23
W
RF
D01
06
93

A
DCHS
DP
A
MC
HS
DP
A+
MI
MO
DL
64Q
AM
+M
IM
O

W
RF
D01
06
14
03
W
RF
D01
06
99
W

HS
UP
A
2ms
TTI
DCHS
DP
A+
MI
MO
Ma
croMic

Description

Meaning: This parameter specifies which HSPA technologies can


be retried by UEs. When the HSPA technologies are selected and
currently UE is not using them, "RNC" will initiate these HSPA
technologies retry for UE.
GUI Value Range: SRB_OVER_HSDPA, SRB_OVER_HSUPA,
TTI_2MS, MIMO, 64QAM, DL_L2_ENHANCE, DTX_DRX,
HSSCCH_LESS_OPERATION, MIMO_64QAM, DC_HSDPA,
UL_L2_ENHANCE, UL_16QAM, EDPCCH_BOOSTING,
DCMIMO_HSDPA, DC_HSUPA, HSDPA_4C_MIMO,
HSDPA_4C, DBMIMO_HSDPA, DB_HSDPA
Unit: None
Actual Value Range: SRB_OVER_HSDPA,
SRB_OVER_HSUPA, TTI_2MS, MIMO, 64QAM,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RF
D15
12
09
W
RF
D15
02
07
W
RF
D01
06
52
W
RF
D01
06
86
W
RF
D01
06
87
W
RF
D01
06
84
W
RF
D-

ro
DCHS
DP
A
4CHS
DP
A
SR
B
ove
r
HS
DP
A
CP
CDT
X/
DR
X
CP
CHSSC
CH
less
ope
rati
on
2x2
MI
MO
Do
wnl
ink
Enh

Description

DL_L2_ENHANCE, DTX_DRX,
HSSCCH_LESS_OPERATION, MIMO_64QAM, DC_HSDPA,
UL_L2_ENHANCE, UL_16QAM, EDPCCH_BOOSTING,
DCMIMO_HSDPA, DC_HSUPA, HSDPA_4C_MIMO,
HSDPA_4C, DBMIMO_HSDPA, DB_HSDPA
Default Value:
SRB_OVER_HSDPA:0,SRB_OVER_HSUPA:0,TTI_2MS:0,MI
MO:1,64QAM:1,DL_L2_ENHANCE:1,DTX_DRX:1,HSSCCH
_LESS_OPERATION:1,MIMO_64QAM:0,DC_HSDPA:0,UL_L
2_ENHANCE:0,UL_16QAM:0,EDPCCH_BOOSTING:0,DCMI
MO_HSDPA:0,DC_HSUPA:0,HSDPA_4C_MIMO:0,HSDPA_4
C:0,DBMIMO_HSDPA:0,DB_HSDPA:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
01
06
85
W
RF
D01
06
95
W
RF
D01
06
83
W
RF
D01
06
97
W
RF
D01
06
94
W
RF
D15
02
27
W
RF
D15
02

anc
ed
L2
UL
Lay
er 2
Imp
rov
eme
nt
Do
wnl
ink
64Q
AM
EDP
CC
H
Boo
stin
g
UL
16Q
AM
DBHS
DP
A+
MI
MO
DBHS
DP
A
3CHS
DP

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

HCSP B ADD
rio
S UCE
C LLH
6 CS
9 MOD
0 UCE
0

09
W
RF
D15
02
50
W
RF
D01
06
36
W
RF
D01
06
96
W
RF
D15
02
23
W
RF
D01
06
93

A
SR
B
ove
r
HS
UP
A
DCHS
DP
A
MC
HS
DP
A+
MI
MO
DL
64Q
AM
+M
IM
O

W
RF
D01
08
01

Intr
a
RN
C
Cell
Upd

Description

Meaning: HCS priority of a cell in an HCS network. The value


of this parameter depends on HCS rules. For details, see 3GPP
TS 25.304. The value 0 indicates the highest-hierarchy cell and
the value 7 indicates the lowest-hierarchy cell. High-hierarchy
cells are macro cells having large coverage areas where UEs
move at high speeds. Low-hierarchy cells are micro cells having

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
LLH
CS

HCSP B ADD
rio
S UCE
C LLH
6 CS
9 MOD
1 UCE
0 LLH
CS

Description

W
RF
D02
12
00
W
RF
D01
08
02

ate
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Inte
r
RN
C
Cell
Upd
ate

small coverage areas where UEs move at low speeds.


GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

W
RF
D01
08
01
W
RF
D02
12
00
W
RF
D01
08
02

Intr
a
RN
C
Cell
Upd
ate
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Inte
r
RN

Meaning: HCS priority of a cell in an HCS network. The value


of this parameter depends on HCS rules. For details, see 3GPP
TS 25.304. The value 0 indicates the highest-hierarchy cell and
the value 7 indicates the lowest-hierarchy cell. High-hierarchy
cells are macro cells having large coverage areas where UEs
move at high speeds. Low-hierarchy cells are micro cells having
small coverage areas where UEs move at low speeds.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

C
Cell
Upd
ate
Blind B ADD W
HoFla S UINT RF
g
C ERFR D6 EQN 02
9 CELL 01
0 MOD 03
0 UINT W
ERFR RF
EQN DCELL 02
12
00
W
RF
D02
01
22
W
RF
D02
04
00
01
W
RF
D02
01
17
W
RF
D-

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Mul
tiCar
rier
Swi
tch
off
Bas
ed
on
Qo
S
Intr
a

Meaning: Whether a neighboring cell is a candidate cell for blind


handovers. Value FALSE indicates that the neighboring cell is
not considered as a candidate cell for blind handovers. Therefore,
blind handovers to this cell cannot be triggered. Value TRUE
indicates that the cell is considered as a candidate cell for blind
handovers and blind handovers to this cell can be triggered.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

02 Syst
04 em
00 Dir
ect
Retr
y
Mul
tiCar
rier
Swi
tch
off
Bas
ed
on
Traf
fic
Loa
d
DR
D
Intr
odu
ctio
n
Pac
kag
e
Blind B ADD W
HoFla S UINT RF
g
C ERFR D6 EQN 02
9 CELL 01
1 MOD 03
0 UINT W
ERFR RF
EQN D-

Inte
r
Fre
que
ncy
Loa
d
Bal
anc

Meaning: Whether a neighboring cell is a candidate cell for blind


handovers. Value FALSE indicates that the neighboring cell is
not considered as a candidate cell for blind handovers. Therefore,
blind handovers to this cell cannot be triggered. Value TRUE
indicates that the cell is considered as a candidate cell for blind
handovers and blind handovers to this cell can be triggered.
GUI Value Range: FALSE, TRUE
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
CELL 02
12
00
W
RF
D02
01
22
W
RF
D02
04
00
01
W
RF
D02
01
17
W
RF
D02
04
00

Description

e
Actual Value Range: FALSE, TRUE
HC Default Value: False
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Mul
tiCar
rier
Swi
tch
off
Bas
ed
on
Qo
S
Intr
a
Syst
em
Dir
ect
Retr
y
Mul
tiCar
rier
Swi
tch
off
Bas

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ed
on
Traf
fic
Loa
d
DR
D
Intr
odu
ctio
n
Pac
kag
e
NFast B ADD
SpdEs S UCE
t
C LLH
6 CSH
9 O
0 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Threshold for determining whether the UE is in the


high-mobility state. After the UE reports event 1D, the UE is
considered to be in the high-mobility state if the number of best
cell changes within the duration specified by "TFastSpdEst" is
greater than this threshold. The smaller the value of this
parameter, the higher the probability that the UE is determined in
the high-mobility state.
GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16
Default Value: 15

NFast B ADD
SpdEs S UCE
t
C LLH
6 CSH
9 O
1 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Threshold for determining whether the UE is in the


high-mobility state. After the UE reports event 1D, the UE is
considered to be in the high-mobility state if the number of best
cell changes within the duration specified by "TFastSpdEst" is
greater than this threshold. The smaller the value of this
parameter, the higher the probability that the UE is determined in
the high-mobility state.
GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Default Value: 15
TFast B ADD
SpdEs S UCE
t
C LLH
6 CSH
9 O
0 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Time window for estimating whether the UE is in the


high-mobility state. The start point of the estimation is the
moment of the last reporting of event 1D, and the backdated time
length is determined by this parameter. If this parameter is set to
0, the RNC does not determine whether the UE is in the highmobility state.
GUI Value Range: 0~511
Unit: s
Actual Value Range: 0~511
Default Value: 180

TFast B ADD
SpdEs S UCE
t
C LLH
6 CSH
9 O
1 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Time window for estimating whether the UE is in the


high-mobility state. The start point of the estimation is the
moment of the last reporting of event 1D, and the backdated time
length is determined by this parameter. If this parameter is set to
0, the RNC does not determine whether the UE is in the highmobility state.
GUI Value Range: 0~511
Unit: s
Actual Value Range: 0~511
Default Value: 180

TCycl B ADD
eSlow S UCE
C LLH
6 CSH
9 O
0 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Period for determine whether the UE is in the lowmobility state. The RNC periodically determines whether the UE
is in the low-mobility state. The smaller the value of this
parameter, the more frequently the state estimation is triggered.
If this parameter is set to 0, the RNC does not determine whether
the UE is in the low-mobility state.
GUI Value Range: 0~255
Unit: s
Actual Value Range: 0~255
Default Value: 60

TCycl B ADD
eSlow S UCE

W HC
RF S

Meaning: Period for determine whether the UE is in the lowmobility state. The RNC periodically determines whether the UE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

C
6
9
1
0

LLH
CSH
O
MOD
UCE
LLH
CSH
O

D02
12
00

(Hi
erar
chic
al
Cell
Stru
ctur
e)

is in the low-mobility state. The smaller the value of this


parameter, the more frequently the state estimation is triggered.
If this parameter is set to 0, the RNC does not determine whether
the UE is in the low-mobility state.
GUI Value Range: 0~255
Unit: s
Actual Value Range: 0~255
Default Value: 60

NSlo
wSpd
Est

B
S
C
6
9
0
0

ADD
UCE
LLH
CSH
O
MOD
UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Threshold for determining whether the UE is in the


low-mobility state. After the UE reports event 1D, the UE is
considered in the low-mobility state if the number of best cell
changes is smaller than this threshold within the period specified
by "TSlowSpdEst". The larger the value of this parameter, the
higher the probability that the UE is determined in the lowmobility state. These slow-speed handover parameters should be
set according to higher and lower level's consistency in order to
prevent ping-pong handover between two layers. For example,
the value of "NFastSpdEst" is usually greater than that of
"NSlowSpdEst".
GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16
Default Value: 3

NSlo
wSpd
Est

B
S
C
6
9
1
0

ADD
UCE
LLH
CSH
O
MOD
UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Threshold for determining whether the UE is in the


low-mobility state. After the UE reports event 1D, the UE is
considered in the low-mobility state if the number of best cell
changes is smaller than this threshold within the period specified
by "TSlowSpdEst". The larger the value of this parameter, the
higher the probability that the UE is determined in the lowmobility state. These slow-speed handover parameters should be
set according to higher and lower level's consistency in order to
prevent ping-pong handover between two layers. For example,
the value of "NFastSpdEst" is usually greater than that of
"NSlowSpdEst".
GUI Value Range: 1~16
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Actual Value Range: 1~16


Default Value: 3
TSlow B ADD
SpdEs S UCE
t
C LLH
6 CSH
9 O
0 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Time window for deciding whether the UE is in the


low-mobility state. Every time the slow speed period timer
expires, the RNC estimates whether the UE is in the lowmobility state. This parameter specifies the duration of the timer.
If this parameter is set to 0, the RNC does not determine whether
the UE is in the low-mobility state.
GUI Value Range: 0~511
Unit: s
Actual Value Range: 0~511
Default Value: 240

TSlow B ADD
SpdEs S UCE
t
C LLH
6 CSH
9 O
1 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Time window for deciding whether the UE is in the


low-mobility state. Every time the slow speed period timer
expires, the RNC estimates whether the UE is in the lowmobility state. This parameter specifies the duration of the timer.
If this parameter is set to 0, the RNC does not determine whether
the UE is in the low-mobility state.
GUI Value Range: 0~511
Unit: s
Actual Value Range: 0~511
Default Value: 240

TRelat B ADD
eLeng S UCE
th
C LLH
6 CSH
9 O
0 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Timer for determining whether ping-pong handovers


occur in the best cell. In the speed estimation algorithm, an
algorithm is adopted to avoid inaccurate estimation caused by
frequent handovers of best cells. During the best cell changes
within the timer duration, if the cell reported in event 1D and the
best cell have the same primary scrambling code, the ping-pong
handover occurs in the best cell. In this case, restore statistics of
best cell changes to the statistical status when event 1D is
reported. If this parameter is set to a large value, the RNC may
mistakenly determine that ping-pong handovers to the best cell
occur. If this parameter is set to a small value, ping-pong
handovers cannot be prevented. Therefore, it is recommended
that this parameter be set according to the cell radius.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

GUI Value Range: 0~120


Unit: s
Actual Value Range: 0~120
Default Value: 10
TRelat B ADD
eLeng S UCE
th
C LLH
6 CSH
9 O
1 MOD
0 UCE
LLH
CSH
O

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Timer for determining whether ping-pong handovers


occur in the best cell. In the speed estimation algorithm, an
algorithm is adopted to avoid inaccurate estimation caused by
frequent handovers of best cells. During the best cell changes
within the timer duration, if the cell reported in event 1D and the
best cell have the same primary scrambling code, the ping-pong
handover occurs in the best cell. In this case, restore statistics of
best cell changes to the statistical status when event 1D is
reported. If this parameter is set to a large value, the RNC may
mistakenly determine that ping-pong handovers to the best cell
occur. If this parameter is set to a small value, ping-pong
handovers cannot be prevented. Therefore, it is recommended
that this parameter be set according to the cell radius.
GUI Value Range: 0~120
Unit: s
Actual Value Range: 0~120
Default Value: 10

TrigTi B ADD
me2C S UCE
C LLIN
6 TERF
9 REQ
0 HON
0 COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Inte
r
Fre
que
ncy

Meaning: Interval between detection of event 2C and sending of


the measurement report.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
TrigTi B ADD
me2C S UCE
C LLIN
6 TERF
9 REQ
1 HON
0 COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: Interval between detection of event 2C and sending of


the measurement report.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

InterF
reqNC
ovHO
ThdEc
N0

B
S
C
6
9
0
0

SET
UINT
ERFR
EQH
ONC
OV

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Threshold of signal quality of the target frequency for


triggering inter-frequency measurement. This parameter is used
to set measurement control on the event 2C. The event 2C is
triggered when the signal quality of the target frequency is above
this threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -16

InterF
reqNC
ovHO
ThdEc
N0

B
S
C
6
9
1
0

SET
UINT
ERFR
EQH
ONC
OV

W
RF
D02
12
00

HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

Meaning: Threshold of signal quality of the target frequency for


triggering inter-frequency measurement. This parameter is used
to set measurement control on the event 2C. The event 2C is
triggered when the signal quality of the target frequency is above
this threshold.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -16

Hystfo B ADD
r2C
S UCE
C LLIN
6 TERF
9 REQ
0 HON
0 COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e

Meaning: Event 2C hysteresis. The hysteresis can be the Ec/No


or RSCP. For details, see 3GPP TS 25.331.
GUI Value Range: 0~29
Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6

Hystfo B ADD
r2C
S UCE

W Inte Meaning: Event 2C hysteresis. The hysteresis can be the Ec/No


RF r
or RSCP. For details, see 3GPP TS 25.331.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

IFAnti
Pingp
angTi
merLe
ngth

Description

C
6
9
1
0

LLIN
TERF
REQ
HON
COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

D02
01
03

Fre
que
ncy
Loa
d
Bal
anc
e

GUI Value Range: 0~29


Unit: 0.5dB
Actual Value Range: 0~14.5
Default Value: 6

B
S
C
6
9
0
0

SET
UHO
COM
M

W
RF
D02
03
09
W
RF
D02
03
04
W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Meaning: Length of a timer for preventing non-coverage-based


inter-frequency handovers. After coverage-based handovers, UE
location-based multi-band DRDs, and macro and micro
correlative inter-frequency handovers are successful, the RNC
starts this timer to prevent frequent handovers or measurements
in the new serving cell caused the non-coverage factors such as
by load, rate estimation, MBMS channel reselection, and QoS.
GUI Value Range: 0~120
Unit: s
Actual Value Range: 0~120
Default Value: 30

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
IFAnti
Pingp
angTi
merLe
ngth

B
S
C
6
9
1
0

SET
UHO
COM
M

W
RF
D02
03
09
W
RF
D02
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL

Meaning: Length of a timer for preventing non-coverage-based


inter-frequency handovers. After coverage-based handovers, UE
location-based multi-band DRDs, and macro and micro
correlative inter-frequency handovers are successful, the RNC
starts this timer to prevent frequent handovers or measurements
in the new serving cell caused the non-coverage factors such as
by load, rate estimation, MBMS channel reselection, and QoS.
GUI Value Range: 0~120
Unit: s
Actual Value Range: 0~120

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
04
W
RF
D02
03
05
W
RF
D02
03
06

Qo Default Value: 30
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on
Loa
d
UseOf B ADD
Hcs
S UEX
C T3GC
6 ELL
9 MOD
0 UEX
0 T3GC
ELL

W
RF
D01
08
01
W
RF
D02
12
00
W
RF
D01
08
02

Intr
a
RN
C
Cell
Upd
ate
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
Inte
r
RN
C
Cell
Upd
ate

Meaning: Whether a cell uses HCS. In a HCS network, macro


cells provide continuous coverage and micro cells provide
hotspot coverage.
GUI Value Range: USED(HCS cell), NOT_USED(Non HCS
cell)
Unit: None
Actual Value Range: USED, NOT_USED
Default Value: NOT_USED(Non HCS cell)

UseOf B ADD
Hcs
S UEX
C T3GC
6 ELL
9 MOD
1 UEX
0 T3GC
ELL

W
RF
D01
08
01
W
RF
D02

Intr
a
RN
C
Cell
Upd
ate
HC
S
(Hi

Meaning: Whether a cell uses HCS. In a HCS network, macro


cells provide continuous coverage and micro cells provide
hotspot coverage.
GUI Value Range: USED(HCS cell), NOT_USED(Non HCS
cell)
Unit: None
Actual Value Range: USED, NOT_USED
Default Value: NOT_USED(Non HCS cell)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

12
00
W
RF
D01
08
02

erar
chic
al
Cell
Stru
ctur
e)
Inte
r
RN
C
Cell
Upd
ate

Blind B ADD
HoFla S U2G
g
C NCE
6 LL
9 MOD
0 U2G
0 NCE
LL

W
RF
D02
04
00
02
W
RF
D02
04
00

Inte
r
Syst
em
Dir
ect
Retr
y
DR
D
Intr
odu
ctio
n
Pac
kag
e

Meaning: Whether a neighboring cell is a candidate cell for blind


handovers. Value FALSE indicates that the neighboring cell is
not considered as a candidate cell for blind handovers. Therefore,
blind handovers to this cell cannot be triggered. Value TRUE
indicates that the cell is considered as a candidate cell for blind
handovers and blind handovers to this cell can be triggered.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

Blind B ADD
HoFla S U2G
g
C NCE
6 LL
9 MOD
1 U2G

W
RF
D02
04
00

Inte
r
Syst
em
Dir
ect

Meaning: Whether a neighboring cell is a candidate cell for blind


handovers. Value FALSE indicates that the neighboring cell is
not considered as a candidate cell for blind handovers. Therefore,
blind handovers to this cell cannot be triggered. Value TRUE
indicates that the cell is considered as a candidate cell for blind
handovers and blind handovers to this cell can be triggered.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0 NCE
LL

Blind B ADD
HOPri S U2G
o
C NCE
6 LL
9 MOD
0 U2G
0 NCE
LL

Description

02
W
RF
D02
04
00

Retr
y
DR
D
Intr
odu
ctio
n
Pac
kag
e

GUI Value Range: FALSE, TRUE


Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

W
RF
D02
03
10
W
RF
D15
02
32
W
RF
D01
06
11
12

3G/
2G
Co
mm
on
Loa
d
Ma
nag
eme
nt
Mul
tiba
nd
Dir
ect
Retr
y
Bas
ed
on
UE
Loc
atio
n
HS
DP

Meaning: Priority of the neighboring cell for a blind handover.


The value 0 represents the highest priority and the value 30
represents the lowest priority. Priorities 0 to 15 are assigned to
concentric neighboring cells, which ensures successful blind
handovers. Priorities 16 to 30 are assigned to the neighboring
cells which allow blind handovers but cannot ensure successful
blind handovers.
GUI Value Range: 0~30
Unit: None
Actual Value Range: 0~30
Default Value: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

A
DR
D
Blind B ADD
HOPri S U2G
o
C NCE
6 LL
9 MOD
1 U2G
0 NCE
LL

W
RF
D02
03
10
W
RF
D15
02
32
W
RF
D01
06
11
12

3G/
2G
Co
mm
on
Loa
d
Ma
nag
eme
nt
Mul
tiba
nd
Dir
ect
Retr
y
Bas
ed
on
UE
Loc
atio
n
HS
DP
A
DR
D

Meaning: Priority of the neighboring cell for a blind handover.


The value 0 represents the highest priority and the value 30
represents the lowest priority. Priorities 0 to 15 are assigned to
concentric neighboring cells, which ensures successful blind
handovers. Priorities 16 to 30 are assigned to the neighboring
cells which allow blind handovers but cannot ensure successful
blind handovers.
GUI Value Range: 0~30
Unit: None
Actual Value Range: 0~30
Default Value: None

TrigTi B ADD
me1F S UCE
C LLIN
6 TRAF

W
RF
D02

Inte
r
RN
C

Meaning: This parameter specifies the interval time between


detection of event 1F and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

9 REQ
0 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

02
03
W
RF
D02
02
02
W
RF
D02
03
02

Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

decision becomes low; however, the handover algorithm


becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an
appropriate interval time effectively reduces the average number
of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

TrigTi B ADD
me1F S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF

W
RF
D02
02
03
W
RF
D02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a

Meaning: This parameter specifies the interval time between


detection of event 1F and sending of the measurement report.
The value of this parameter is associated with slow fading. If this
parameter is set to a greater value, the probability of incorrect
decision becomes low; however, the handover algorithm
becomes slow in responding to signal change. The time-totrigger mechanism is introduced for the following purposes: reducing the number of wrong event reports caused by burst
signals, - preventing the ping-pong handover, - reducing the
impact of shadow fading on event decisions. Setting an

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

REQ
HO

02
02
W
RF
D02
03
02

RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

appropriate interval time effectively reduces the average number


of handovers and the number of wrong handovers, preventing
unnecessary handovers.
GUI Value Range: D0, D10, D20, D40, D60, D80, D100, D120,
D160, D200, D240, D320, D640, D1280, D2560, D5000
Unit: ms
Actual Value Range: 0, 10, 20, 40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
Default Value: D640

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: RSCP absolute threshold for event 1F in the software


handover algorithm. This parameter must be set to a value that
guarantees the quality of basic services. In addition, the setting
of this parameter affects event 1F triggering. Event 1F is
reported to trigger an emergent blind handover. If event 1F is
reported for a cell in the active set, the signal quality of the
active set is poor. Under this situation, a blind handover is
triggered to prevent call drops. Emergent blind handovers are
triggered in special occasions that require on-site measurement
of the pilot strength and signal quality of the best cell where the
UE is located. This function is rarely used. Therefore, this
parameter is set to the smallest value by default. For the event
definition, see 3GPP TS 25.331.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25

IntraA
blThd
For1F
RSCP

B
S
C
6
9
0
0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

03 Inte Default Value: -115


02 r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
IntraA
blThd
For1F
RSCP

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D02
03
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har

Meaning: RSCP absolute threshold for event 1F in the software


handover algorithm. This parameter must be set to a value that
guarantees the quality of basic services. In addition, the setting
of this parameter affects event 1F triggering. Event 1F is
reported to trigger an emergent blind handover. If event 1F is
reported for a cell in the active set, the signal quality of the
active set is poor. Under this situation, a blind handover is
triggered to prevent call drops. Emergent blind handovers are
triggered in special occasions that require on-site measurement
of the pilot strength and signal quality of the best cell where the
UE is located. This function is rarely used. Therefore, this
parameter is set to the smallest value by default. For the event
definition, see 3GPP TS 25.331.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -115

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

d
Han
dov
er
Bas
ed
on
Cov
erag
e
IntraA
blThd
For1F
EcNo

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D02
03
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed

Meaning: Ec/No absolute threshold for event 1F in the software


handover algorithm. This parameter must be set to a value that
guarantees the quality of basic services. In addition, the setting
of this parameter affects event 1F triggering. Event 1F is
reported to trigger an emergent blind handover. If event 1F is
reported for a cell in the active set, the signal quality of the
active set is poor. Under this situation, a blind handover is
triggered to prevent call drops. Emergent blind handovers are
triggered in special occasions that require on-site measurement
of the pilot strength and signal quality of the best cell where the
UE is located. This function is rarely used. Therefore, this
parameter is set to the smallest value by default. For the event
definition, see 3GPP TS 25.331.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -24

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on
Cov
erag
e
IntraA
blThd
For1F
EcNo

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

HystF B ADD

W
RF
D02
02
03
W
RF
D02
02
02
W
RF
D02
03
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Ec/No absolute threshold for event 1F in the software


handover algorithm. This parameter must be set to a value that
guarantees the quality of basic services. In addition, the setting
of this parameter affects event 1F triggering. Event 1F is
reported to trigger an emergent blind handover. If event 1F is
reported for a cell in the active set, the signal quality of the
active set is poor. Under this situation, a blind handover is
triggered to prevent call drops. Emergent blind handovers are
triggered in special occasions that require on-site measurement
of the pilot strength and signal quality of the best cell where the
UE is located. This function is rarely used. Therefore, this
parameter is set to the smallest value by default. For the event
definition, see 3GPP TS 25.331.
GUI Value Range: -24~0
Unit: dB
Actual Value Range: -24~0
Default Value: -24

W Inte Meaning: This parameter specifies the hysteretic value for event

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
or1F

S
C
6
9
0
0

Description

UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

RF
D02
02
03
W
RF
D02
02
02
W
RF
D02
03
02

r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

1F. The value of this parameter is associated with the slow


fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331. In addition, filter coefficient
and interval time must be considered in setting this parameter.
GUI Value Range: 0~15
Unit: 0.5dB
Actual Value Range: 0~7.5
Default Value: 8

HystF B ADD
or1F S UCE
C LLIN
6 TRAF
9 REQ
1 HO
0 MOD

W
RF
D02
02
03
W

Inte
r
RN
C
Soft
Han
dov

Meaning: This parameter specifies the hysteretic value for event


1F. The value of this parameter is associated with the slow
fading, and it can be used to reduce ping-pong handovers and
incorrect handovers. For details on the definition of this
parameter, see 3GPP TS 25.331. In addition, filter coefficient
and interval time must be considered in setting this parameter.
GUI Value Range: 0~15

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Blind
HORS
CP1F
Thres
hold

B
S
C
6
9
0
0

Description

UCE
LLIN
TRAF
REQ
HO

RF
D02
02
02
W
RF
D02
03
02

er
Unit: 0.5dB
Intr Actual Value Range: 0~7.5
a
Default Value: 8
RN
C
Soft
Han
dov
er
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Meaning: Quality threshold for triggering an emergent blind


handover to a cell in the event 1F report. A blind handover is
triggered only when the signal quality of a cell in the event 1F
report exceeds the value of this parameter. Otherwise, the report
is discarded. This parameter is used to increase the success rate
of blind handovers. If the signal quality of all the cells in the
event 1F report is poor, the UE may be located at the edge of the
coverage area. Under this situation, triggering blind handovers
may cause call drops.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Cov Default Value: -115


erag
e
Blind
HORS
CP1F
Thres
hold

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Quality threshold for triggering an emergent blind


handover to a cell in the event 1F report. A blind handover is
triggered only when the signal quality of a cell in the event 1F
report exceeds the value of this parameter. Otherwise, the report
is discarded. This parameter is used to increase the success rate
of blind handovers. If the signal quality of all the cells in the
event 1F report is poor, the UE may be located at the edge of the
coverage area. Under this situation, triggering blind handovers
may cause call drops.
GUI Value Range: -115~-25
Unit: dBm
Actual Value Range: -115~-25
Default Value: -115

IFHoP
ingPo
ngTim
er

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy

Meaning: Duration after which the coverage-based interfrequency handover, inter-frequency blind handover triggered by
event 1F, or QoS-based inter-frequency handover can be reinitiated after the success of such handover.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
IFHoP
ingPo
ngTim
er

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
09
W
RF
D02
03
02

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: Duration after which the coverage-based interfrequency handover, inter-frequency blind handover triggered by
event 1F, or QoS-based inter-frequency handover can be reinitiated after the success of such handover.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag
e
InterR
ATPin
gPong
Hyst

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis to avoid ping-pong handover between 2G


and 3G networks. When a UE in the CS domain is handed over
from a 2G network to a 3G network, the system increases the
hysteresis used for event 3A to prevent the ping-pong handover
between the 2G network and the 3G network in the handover
penalty period specified by "InterRATPingPongTimer". During
the penalty time, event-triggered reporting is used for inter-RAT
measurement. The value 0 indicates that the system does not take
measures to avoid ping-pong handover between 2G and 3G
networks.
GUI Value Range: 0~15
Unit: 0.5dBm
Actual Value Range: 0~7.5
Default Value: 0

InterR
ATPin
gPong
Hyst

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Hysteresis to avoid ping-pong handover between 2G


and 3G networks. When a UE in the CS domain is handed over
from a 2G network to a 3G network, the system increases the
hysteresis used for event 3A to prevent the ping-pong handover
between the 2G network and the 3G network in the handover
penalty period specified by "InterRATPingPongTimer". During
the penalty time, event-triggered reporting is used for inter-RAT
measurement. The value 0 indicates that the system does not take
measures to avoid ping-pong handover between 2G and 3G
networks.
GUI Value Range: 0~15
Unit: 0.5dBm
Actual Value Range: 0~7.5
Default Value: 0

InterR
ATPin
gPong
Timer

B
S
C
6
9

ADD
UCE
LLIN
TERR
ATH

W
RF
D02
03

Inte
rRA
T
Han

Meaning: Length of the timer to avoid ping-pong handovers


between 2G and 3G networks. When a UE in the CS domain is
handed over from a 2G network to a 3G network, the system
increases the hysteresis used for event 3A to prevent the pingpong handover between the 2G network and the 3G network in

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

InterR
ATPin
gPong
Timer

Description

0 OCO 03 dov
0 V
er
Bas
MOD
ed
UCE
on
LLIN
Cov
TERR
erag
ATH
e
OCO
V

the period specified by this parameter. During the penalty time,


the previous periodical report will be changed to the event 3A
report. The value 0 indicates that the system does not take
measures to avoid ping-pong handover between 2G and 3G
networks.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Length of the timer to avoid ping-pong handovers


between 2G and 3G networks. When a UE in the CS domain is
handed over from a 2G network to a 3G network, the system
increases the hysteresis used for event 3A to prevent the pingpong handover between the 2G network and the 3G network in
the period specified by this parameter. During the penalty time,
the previous periodical report will be changed to the event 3A
report. The value 0 indicates that the system does not take
measures to avoid ping-pong handover between 2G and 3G
networks.
GUI Value Range: 0~65535
Unit: s
Actual Value Range: 0~65535
Default Value: 0

Period B ADD
For2B S UCE
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC

W
RF
D02
03
02
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on

Meaning: Sets the interval between the failure in the interfrequency handover triggered by the event 2B and the interfrequency handover retry.
GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 1

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
OV

Period B ADD
For2B S UCE
C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

Description

Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
W
RF
D02
03
02
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre

Meaning: Sets the interval between the failure in the interfrequency handover triggered by the event 2B and the interfrequency handover retry.
GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 1

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Amnt B ADD
OfRpt S UCE
2B
C LLIN
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov

Meaning: Maximum number of inter-frequency handover reattempts after event 2B is reported but the UE fails to be handed
over to the target cell.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 4

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Bas
ed
on
DL
Qo
S
Amnt B ADD
OfRpt S UCE
2B
C LLIN
6 TERF
9 REQ
1 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo

Meaning: Maximum number of inter-frequency handover reattempts after event 2B is reported but the UE fails to be handed
over to the target cell.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 4

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

S
Period B ADD
For2C S UCE
C LLIN
6 TERF
9 REQ
0 HON
0 COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: Interval between inter-frequency handover re-attempts


made by RNC after an inter-frequency handover triggered by
event 2C fails.
GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 4

Period B ADD
For2C S UCE
C LLIN
6 TERF
9 REQ
1 HON
0 COV
MOD
UCE
LLIN

W
RF
D02
01
03
W
RF
D02

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e

Meaning: Interval between inter-frequency handover re-attempts


made by RNC after an inter-frequency handover triggered by
event 2C fails.
GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 4

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

TERF 03 Inte
REQ 04 r
HON
Fre
COV
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Amnt B ADD
OfRpt S UCE
2C
C LLIN
6 TERF
9 REQ
0 HON
0 COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03
W
RF
D02
03
02
W
RF
D02
03
04

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e

Meaning: Maximum number of inter-frequency handover reattempts after event 2C is reported but the UE fails to be handed
over to the target cell.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 1

Amnt B ADD W Inte Meaning: Maximum number of inter-frequency handover reOfRpt S UCE RF r
attempts after event 2C is reported but the UE fails to be handed
2C
C LLIN D- Fre over to the target cell.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
6
9
1
0

Description

TERF
REQ
HON
COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

02
01
03
W
RF
D02
03
02
W
RF
D02
03
04

que
ncy
Loa
d
Bal
anc
e

GUI Value Range: 0~63


Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 1

Period B ADD
For3A S UCE
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Interval between handover attempts for event 3A.


GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 1

Period B ADD
For3A S UCE
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas

Meaning: Interval between handover attempts for event 3A.


GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 1

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UCE
LLIN
TERR
ATH
OCO
V

Description

ed
on
Cov
erag
e

Amnt B ADD
OfRpt S UCE
3A
C LLIN
6 TERR
9 ATH
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Number of handover attempts after the UE sends to the


CN a message indicating that inter-RAT handovers triggered by
event 3A fail.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 4

Amnt B ADD
OfRpt S UCE
3A
C LLIN
6 TERR
9 ATH
1 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
03

Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Number of handover attempts after the UE sends to the


CN a message indicating that inter-RAT handovers triggered by
event 3A fail.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 4

Period B ADD
For3C S UCE

W Inte Meaning: Interval between handover attempts for event 3A.


RF rGUI Value Range: 1~64

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
C
6
9
0
0

Description

LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

D02
03
05
W
RF
D02
03
06

RA Unit: 500ms
T
Actual Value Range: 500~32000
Han Default Value: 4
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Period B ADD
For3C S UCE
C LLIN
6 TERR
9 ATH
1 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T

Meaning: Interval between handover attempts for event 3A.


GUI Value Range: 1~64
Unit: 500ms
Actual Value Range: 500~32000
Default Value: 4

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Han
dov
er
Bas
ed
on
Loa
d
Amnt B ADD
OfRpt S UCE
3C
C LLIN
6 TERR
9 ATH
0 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Meaning: Number of handover attempts after the UE sends to the


CN a message indicating that inter-RAT handovers triggered by
event 3C fail.
GUI Value Range: 0~63
Unit: None
Actual Value Range: 0~62, 63(Infinity)
Default Value: 1

Amnt B ADD
OfRpt S UCE
3C
C LLIN
6 TERR
9 ATH

W
RF
D02
03

Inte
rRA
T
Han

Meaning: Number of handover attempts after the UE sends to the


CN a message indicating that inter-RAT handovers triggered by
event 3C fail.
GUI Value Range: 0~63
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Report
Interv
alfor1
A

Description

1 ONC
0 OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

05
W
RF
D02
03
06

dov Actual Value Range: 0~62, 63(Infinity)


er
Default Value: 1
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

B
S
C
6
9
0
0

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

Report B ADD
Interv S UCE

Meaning: Interval at which event 1A is reported after the


reporting mode is changed to periodical reporting. Generally,
event 1A is reported only once. To avoid the loss of
measurement reports, the UE sets the mode of reporting event
1A to periodical if the cell reporting event 1A is not added to the
active set in a specified period of time. Event 1A is reported for
"PeriodMRReportNumfor1A" times at the interval specified by
this parameter. If the mode of reporting event 1A is set to
"NON_PERIODIC_REPORT", the UE cannot change the event
1A reporting mode to periodical.
GUI Value Range: NON_PERIODIC_REPORT, D250, D500,
D1000, D2000, D4000, D8000, D16000
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 4000, 8000, 16000
Default Value: D4000

W Inte Meaning: Interval at which event 1A is reported after the


RF r
reporting mode is changed to periodical reporting. Generally,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

alfor1 C LLIN
A
6 TRAF
9 REQ
1 HO
0 MOD
UCE
LLIN
TRAF
REQ
HO

D02
02
03
W
RF
D02
02
02

RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

event 1A is reported only once. To avoid the loss of


measurement reports, the UE sets the mode of reporting event
1A to periodical if the cell reporting event 1A is not added to the
active set in a specified period of time. Event 1A is reported for
"PeriodMRReportNumfor1A" times at the interval specified by
this parameter. If the mode of reporting event 1A is set to
"NON_PERIODIC_REPORT", the UE cannot change the event
1A reporting mode to periodical.
GUI Value Range: NON_PERIODIC_REPORT, D250, D500,
D1000, D2000, D4000, D8000, D16000
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 4000, 8000, 16000
Default Value: D4000

Report
Interv
alfor1
C

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Interval at which event 1A is reported after the


reporting mode is changed to periodical reporting. Generally,
event 1C is reported only once. To avoid the loss of
measurement reports, the UE set the mode of reporting event 1C
to periodical if the cell reporting event 1C is not added to the
active set in a specified period of time. Event 1C is reported for
"PeriodMRReportNumfor1C" times at the interval specified by
this parameter.If the mode of reporting event 1C is set to
"NON_PERIODIC_REPORT", the UE cannot change the event
1C reporting mode to periodical.
GUI Value Range: NON_PERIODIC_REPORT, D250, D500,
D1000, D2000, D4000, D8000, D16000
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 4000, 8000, 16000
Default Value: D4000

Report
Interv
alfor1
C

B
S
C
6
9
1

ADD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03

Inte
r
RN
C
Soft
Han

Meaning: Interval at which event 1A is reported after the


reporting mode is changed to periodical reporting. Generally,
event 1C is reported only once. To avoid the loss of
measurement reports, the UE set the mode of reporting event 1C
to periodical if the cell reporting event 1C is not added to the
active set in a specified period of time. Event 1C is reported for

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

0 MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
02

dov
er
Intr
a
RN
C
Soft
Han
dov
er

"PeriodMRReportNumfor1C" times at the interval specified by


this parameter.If the mode of reporting event 1C is set to
"NON_PERIODIC_REPORT", the UE cannot change the event
1C reporting mode to periodical.
GUI Value Range: NON_PERIODIC_REPORT, D250, D500,
D1000, D2000, D4000, D8000, D16000
Unit: ms
Actual Value Range: NON_PERIODIC_REPORT, 250, 500,
1000, 2000, 4000, 8000, 16000
Default Value: D4000

Period
MRRe
portN
umfor
1A

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Number of times event 1A is reported after the


reporting mode is changed to periodic reporting. When the
number of times event 1A is reported exceeds this parameter
value, periodic reporting of event 1A is disabled.
GUI Value Range: D1, D2, D4, D8, D16, D32, D64, INFINITY
Unit: None
Actual Value Range: 1, 2, 4, 8, 16, 32, 64, INFINITY
Default Value: D16

Period
MRRe
portN
umfor
1A

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF

W
RF
D02
02
03
W
RF
D02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a

Meaning: Number of times event 1A is reported after the


reporting mode is changed to periodic reporting. When the
number of times event 1A is reported exceeds this parameter
value, periodic reporting of event 1A is disabled.
GUI Value Range: D1, D2, D4, D8, D16, D32, D64, INFINITY
Unit: None
Actual Value Range: 1, 2, 4, 8, 16, 32, 64, INFINITY
Default Value: D16

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
REQ
HO

02 RN
02 C
Soft
Han
dov
er

Description

Period
MRRe
portN
umfor
1C

B
S
C
6
9
0
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Number of times event 1C is reported after the


reporting mode is changed to periodic reporting. When the
number of times event 1C is reported exceeds this parameter
value, periodic reporting of event 1C is disabled.
GUI Value Range: D1, D2, D4, D8, D16, D32, D64, INFINITY
Unit: None
Actual Value Range: 1, 2, 4, 8, 16, 32, 64, INFINITY
Default Value: D16

Period
MRRe
portN
umfor
1C

B
S
C
6
9
1
0

ADD
UCE
LLIN
TRAF
REQ
HO
MOD
UCE
LLIN
TRAF
REQ
HO

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov

Meaning: Number of times event 1C is reported after the


reporting mode is changed to periodic reporting. When the
number of times event 1C is reported exceeds this parameter
value, periodic reporting of event 1C is disabled.
GUI Value Range: D1, D2, D4, D8, D16, D32, D64, INFINITY
Unit: None
Actual Value Range: 1, 2, 4, 8, 16, 32, 64, INFINITY
Default Value: D16

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
NPrio B ADD
Flag
S UINT
C RAF
6 REQ
9 NCE
0 LL
0 MOD
UINT
RAF
REQ
NCE
LL

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether to configure the priority flag for a


neighboring cell. The value FALSE indicates that the
neighboring cell priority is not configured. In the algorithm of
neighboring cell combination, the cell with an invalid priority is
the last one to be considered as the measurement object. The
value TRUE indicates that the neighboring cell priority is
configured. When the algorithm of neighboring cell combination
(controlled by "HO_MC_NCELL_COMBINE_SWITCH") is
enabled and the total number of neighboring cells to all cells in
the active set exceeds 32, the RNC considers this parameter as
one of conditions for selecting the neighboring cells. That is, a
neighboring cell with a high priority is preferentially selected. If
a neighboring cell is not configured with the priority flag, the
lowest priority is assigned to this cell.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: False

NPrio B ADD
Flag
S UINT
C RAF
6 REQ
9 NCE
1 LL
0 MOD
UINT
RAF
REQ
NCE
LL

W
RF
D02
03
02

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether to configure the priority flag for a


neighboring cell. The value FALSE indicates that the
neighboring cell priority is not configured. In the algorithm of
neighboring cell combination, the cell with an invalid priority is
the last one to be considered as the measurement object. The
value TRUE indicates that the neighboring cell priority is
configured. When the algorithm of neighboring cell combination
(controlled by "HO_MC_NCELL_COMBINE_SWITCH") is
enabled and the total number of neighboring cells to all cells in
the active set exceeds 32, the RNC considers this parameter as
one of conditions for selecting the neighboring cells. That is, a
neighboring cell with a high priority is preferentially selected. If
a neighboring cell is not configured with the priority flag, the
lowest priority is assigned to this cell.
GUI Value Range: FALSE, TRUE
Unit: None
Actual Value Range: FALSE, TRUE

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Default Value: False


NPrio B
S
C
6
9
0
0

ADD
UINT
RAF
REQ
NCE
LL
MOD
UINT
RAF
REQ
NCE
LL

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Priority of a neighboring cell. The smaller the value of


this parameter, the higher the priority of a neighboring cell. If
"NPrioFlag" of a neighboring cell is set to False, the neighboring
cell has the lowest priority. If the total number of neighboring
cells exceeds 32, the RNC considers this parameter as a
condition for selecting neighboring cells. That is, a neighboring
cell with a high priority is preferentially measured.
GUI Value Range: 0~30
Unit: None
Actual Value Range: 0~30
Default Value: None

NPrio B
S
C
6
9
1
0

ADD
UINT
RAF
REQ
NCE
LL
MOD
UINT
RAF
REQ
NCE
LL

W
RF
D02
02
03
W
RF
D02
02
02

Inte
r
RN
C
Soft
Han
dov
er
Intr
a
RN
C
Soft
Han
dov
er

Meaning: Priority of a neighboring cell. The smaller the value of


this parameter, the higher the priority of a neighboring cell. If
"NPrioFlag" of a neighboring cell is set to False, the neighboring
cell has the lowest priority. If the total number of neighboring
cells exceeds 32, the RNC considers this parameter as a
condition for selecting neighboring cells. That is, a neighboring
cell with a high priority is preferentially measured.
GUI Value Range: 0~30
Unit: None
Actual Value Range: 0~30
Default Value: None

IntraF B SET No Non Meaning: Whether the detection function of missing intrareqNC S UNC ne e
frequency neighboring cells is enabled. This switch is turned on.
ellDet C ELLD
The function of detecting missing intra-frequency neighboring

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ectSwi 6 ETEC
tch
9 TSWI
0 TCH
0

cells is enabled. That is, the UE reports the intra-frequency


measurement results in the detection set to the RNC and the
RNC then reports the detected missing intra-frequency
neighboring cells to the Nastar or LMT. This switch is turned off.
The function of detecting missing intra-frequency neighboring
cells is not enabled.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

IntraF
reqNC
ellDet
ectSwi
tch

B
S
C
6
9
1
0

SET No Non
UNC ne e
ELLD
ETEC
TSWI
TCH

Meaning: Whether the detection function of missing intrafrequency neighboring cells is enabled. This switch is turned on.
The function of detecting missing intra-frequency neighboring
cells is enabled. That is, the UE reports the intra-frequency
measurement results in the detection set to the RNC and the
RNC then reports the detected missing intra-frequency
neighboring cells to the Nastar or LMT. This switch is turned off.
The function of detecting missing intra-frequency neighboring
cells is not enabled.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

InterF
reqNC
ellDet
ectSwi
tch

B
S
C
6
9
0
0

SET No Non
UNC ne e
ELLD
ETEC
TSWI
TCH

Meaning: Whether the function of detecting missing interfrequency neighboring cells is enabled. This switch is turned on.
The function of detecting missing inter-frequency neighboring
cells is enabled. That is, the UE reports the inter-frequency
measurement results to the RNC and the RNC then reports the
detected missing inter-frequency neighboring cells to the Nastar
or LMT. This switch is turned off. The function of detecting
missing inter-frequency neighboring cells is not enabled.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
InterF
reqNC
ellDet
ectSwi
tch

B
S
C
6
9
1
0

SET No Non
UNC ne e
ELLD
ETEC
TSWI
TCH

DlSFL B SET W
imitC S UCM RF
MInd C CF
D6
02
9
03
0
02
0
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on

Description

Meaning: Whether the function of detecting missing interfrequency neighboring cells is enabled. This switch is turned on.
The function of detecting missing inter-frequency neighboring
cells is enabled. That is, the UE reports the inter-frequency
measurement results to the RNC and the RNC then reports the
detected missing inter-frequency neighboring cells to the Nastar
or LMT. This switch is turned off. The function of detecting
missing inter-frequency neighboring cells is not enabled.
GUI Value Range: OFF, ON
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF
Meaning: Whether the CM is limited by the downlink spreading
factor (SF). Starting the compressed mode is resource consuming
for the fast-moving UEs, so this parameter is set to control
whether the downlink SF of the current DCH channel should be
considered. When this parameter is set to FALSE, the enabling
of CM does not consider the SF of the downlink DCH channel;
when this parameter is set to TRUE, the enabling of CM
considers the SF of the downlink DCH channel.
GUI Value Range: FALSE(Not Limited), TRUE(Limited)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: FALSE(Not Limited)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Cov
erag
e
DlSFL B SET W
imitC S UCM RF
MInd C CF
D6
02
9
03
1
02
0
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether the CM is limited by the downlink spreading


factor (SF). Starting the compressed mode is resource consuming
for the fast-moving UEs, so this parameter is set to control
whether the downlink SF of the current DCH channel should be
considered. When this parameter is set to FALSE, the enabling
of CM does not consider the SF of the downlink DCH channel;
when this parameter is set to TRUE, the enabling of CM
considers the SF of the downlink DCH channel.
GUI Value Range: FALSE(Not Limited), TRUE(Limited)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: FALSE(Not Limited)

Limit B SET W
CMDl S UCM RF
SFThd C CF
D6
02
9
03

Inte
r
Fre
que
ncy

Meaning: Downlink SF threshold for enabling compressed mode


(CM). When the parameter "DlSFLimitCMInd" is set to TRUE
and the current downlink SF is smaller than or equal to the value
of this parameter, the active set quality measurement is not
allowed, that is, the CM cannot be enabled. When the parameter

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0
0

Description

02
W
RF
D02
03
03

Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

"DlSFLimitCMInd" is set to TRUE and the current downlink SF


is greater than the value of this parameter, the active set quality
measurement is allowed, that is, the CM can be enabled.
GUI Value Range: D8, D16, D32, D64, D128, D256
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 256
Default Value: D8

Limit B SET W
CMDl S UCM RF
SFThd C CF
D6
02
9
03
1
02
0
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: Downlink SF threshold for enabling compressed mode


(CM). When the parameter "DlSFLimitCMInd" is set to TRUE
and the current downlink SF is smaller than or equal to the value
of this parameter, the active set quality measurement is not
allowed, that is, the CM cannot be enabled. When the parameter
"DlSFLimitCMInd" is set to TRUE and the current downlink SF
is greater than the value of this parameter, the active set quality
measurement is allowed, that is, the CM can be enabled.
GUI Value Range: D8, D16, D32, D64, D128, D256
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 256
Default Value: D8

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Cmcf
Switc
h

B
S
C
6
9
0
0

SET
UCO
RRM
ALG
OSWI
TCH

W
RF
D01
06
10
06
W
RF
D02
03
10
W
RF
D02
03
09
W
RF
D02

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
3G/
2G
Co
mm
on
Loa
d
Ma
nag
eme
nt
Inte
r-

Meaning: CMCF algorithm switch group. 1.


CMCF_DL_HLS_SWITCH: When the switch is on, the
compressed mode supports DL higher-layer scheduling. 2.
CMCF_UL_HLS_SWITCH: When the switch is on, the
compressed mode supports UL higher-layer scheduling. 3.
CMCF_UL_PRECFG_TOLERANCE_SWITCH: When the
switch is on, the compressed mode of the UE in the compressed
mode pre-configuration state can be different from that required
by current traffic. 4.
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH: When the
RNC starts inter-frequency or inter-RAT measurement, the RNC
checks the information of whether the compressed mode is
required for measurement on the frequency band of the cells in
measurement list. The information should be reported by the UE
in RRC connect setup complete message. When the switch is on
and no such information has been reported, the RNC starts the
compressed mode and then delivers the measurement. 5.
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH: Whether
the scrambling code is replaced when the downlink compressed
mode is SF/2 for UEs and a brother child code tree of the current
code is occupied. When this switch is turned on, another vacant
code is used when the downlink compressed mode is SF/2 for
UEs and a brother child code tree of the current code is

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
03
08
02
W
RF
D02
03
08
W
RF
D01
06
12
04
W
RF
D02
03
02
W
RF
D02
03
03
W
RF
D02
03
04
W
RF
D02

RA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
PS
Han
dov
er
Bet
wee
n
UM
TS
and
GP
RS
Inte
rRA
T
Han
dov
er
Pha
se 2
HS
UP
A
Mo
bilit
y
Ma

Description

occupied. When this switch is turned off, the scrambling code is


replaced when the downlink compressed mode is SF/2 for UEs
and a brother child code tree of the current code is occupied.
Disuse Statement:The value range of this parameter is reduced,
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH is
deleted in later versions. The configuration interface in this
version has no change. If the switch
"CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH" is
enabled, the system has no process automatically . Therefore,
this switch is not recommended.
GUI Value Range: CMCF_DL_HLS_SWITCH,
CMCF_UL_HLS_SWITCH,
CMCF_UL_PRECFG_TOLERANCE_SWITCH,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH,
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH
Unit: None
Actual Value Range: CMCF_DL_HLS_SWITCH,
CMCF_UL_HLS_SWITCH,
CMCF_UL_PRECFG_TOLERANCE_SWITCH,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH,
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH
Default Value:
CMCF_DL_HLS_SWITCH:1,CMCF_UL_HLS_SWITCH:1,C
MCF_UL_PRECFG_TOLERANCE_SWITCH:0,CMCF_WITH
OUT_UE_CAP_REPORT_SWITCH:0,CMCF_AVOID_DL_SF
_2_CHG_SCCODE_SWITCH:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
03
05
W
RF
D02
03
06

nag
eme
nt
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
Cmcf
Switc
h

B
S
C
6
9

SET
UCO
RRM
ALG
OSWI

W
RF
D01
06

HS
DP
A
Mo
bilit

Meaning: CMCF algorithm switch group. 1.


CMCF_DL_HLS_SWITCH: When the switch is on, the
compressed mode supports DL higher-layer scheduling. 2.
CMCF_UL_HLS_SWITCH: When the switch is on, the
compressed mode supports UL higher-layer scheduling. 3.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
1 TCH
0

10
06
W
RF
D02
03
10
W
RF
D02
03
09
W
RF
D02
03
08
02
W
RF
D02
03
08
W
RF
D01
06
12
04
W
RF
D02

y
Ma
nag
eme
nt
3G/
2G
Co
mm
on
Loa
d
Ma
nag
eme
nt
Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
PS
Han
dov
er
Bet
wee
n
UM
TS
and

Description

CMCF_UL_PRECFG_TOLERANCE_SWITCH: When the


switch is on, the compressed mode of the UE in the compressed
mode pre-configuration state can be different from that required
by current traffic. 4.
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH: When the
RNC starts inter-frequency or inter-RAT measurement, the RNC
checks the information of whether the compressed mode is
required for measurement on the frequency band of the cells in
measurement list. The information should be reported by the UE
in RRC connect setup complete message. When the switch is on
and no such information has been reported, the RNC starts the
compressed mode and then delivers the measurement. 5.
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH: Whether
the scrambling code is replaced when the downlink compressed
mode is SF/2 for UEs and a brother child code tree of the current
code is occupied. When this switch is turned on, another vacant
code is used when the downlink compressed mode is SF/2 for
UEs and a brother child code tree of the current code is
occupied. When this switch is turned off, the scrambling code is
replaced when the downlink compressed mode is SF/2 for UEs
and a brother child code tree of the current code is occupied.
Disuse Statement:The value range of this parameter is reduced,
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH is
deleted in later versions. The configuration interface in this
version has no change. If the switch
"CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH" is
enabled, the system has no process automatically . Therefore,
this switch is not recommended.
GUI Value Range: CMCF_DL_HLS_SWITCH,
CMCF_UL_HLS_SWITCH,
CMCF_UL_PRECFG_TOLERANCE_SWITCH,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH,
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH
Unit: None
Actual Value Range: CMCF_DL_HLS_SWITCH,
CMCF_UL_HLS_SWITCH,
CMCF_UL_PRECFG_TOLERANCE_SWITCH,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH,
CMCF_AVOID_DL_SF_2_CHG_SCCODE_SWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
03
02
W
RF
D02
03
03
W
RF
D02
03
04
W
RF
D02
03
05
W
RF
D02
03
06

GP
RS
Inte
rRA
T
Han
dov
er
Pha
se 2
HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r-

Description

Default Value:
CMCF_DL_HLS_SWITCH:1,CMCF_UL_HLS_SWITCH:1,C
MCF_UL_PRECFG_TOLERANCE_SWITCH:0,CMCF_WITH
OUT_UE_CAP_REPORT_SWITCH:0,CMCF_AVOID_DL_SF
_2_CHG_SCCODE_SWITCH:0

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
RA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice

Description

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
DlSFT B ADD
urnPoi S UCE
nt
C LLC
6 MCF
9 MOD
0 UCE
0 LLC
MCF

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on

Meaning: Spreading factor (SF) threshold for UEs to start the


CM in the downlink in a cell. When the downlink spreading
factor is greater than or equal to the value of this parameter, the
SF/2 mode is preferred. Otherwise, the high-layer scheduling
mode is preferred. The SF/2 mode consumes more system
resources than the high-layer scheduling mode. Therefore, this
mode is recommended only for low-rate users. The high-layer
scheduling mode requires variable multiplexing positions of
transport channels and is applicable to a relatively narrow range.
In addition, this approach affects the transmission rate of users.
Therefore, this mode is recommended only when the SF/2
approach is unavailable or there are high-rate users.
GUI Value Range: D8, D16, D32, D64, D128, D256
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 256
Default Value: D64

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Cov
erag
e
DlSFT B ADD
urnPoi S UCE
nt
C LLC
6 MCF
9 MOD
1 UCE
0 LLC
MCF

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Spreading factor (SF) threshold for UEs to start the


CM in the downlink in a cell. When the downlink spreading
factor is greater than or equal to the value of this parameter, the
SF/2 mode is preferred. Otherwise, the high-layer scheduling
mode is preferred. The SF/2 mode consumes more system
resources than the high-layer scheduling mode. Therefore, this
mode is recommended only for low-rate users. The high-layer
scheduling mode requires variable multiplexing positions of
transport channels and is applicable to a relatively narrow range.
In addition, this approach affects the transmission rate of users.
Therefore, this mode is recommended only when the SF/2
approach is unavailable or there are high-rate users.
GUI Value Range: D8, D16, D32, D64, D128, D256
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 256
Default Value: D64

UlSFT B ADD
urnPoi S UCE
nt
C LLC
6 MCF
9 MOD

W
RF
D02
03

Inte
r
Fre
que
ncy

Meaning: SF threshold for UEs to start the CM in the uplink in a


cell. When the uplink spreading factor is greater than or equal to
the value of this parameter, the SF/2 mode is preferred.
Otherwise, the high-layer scheduling mode is preferred. The
SF/2 mode consumes more system resources than the high-layer

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

0 UCE
0 LLC
MCF

02
W
RF
D02
03
03

Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

scheduling mode. Therefore, this mode is recommended only for


low-rate users. The high-layer scheduling mode requires variable
multiplexing positions of transport channels and is applicable to
a relatively narrow range. In addition, this approach affects the
transmission rate of users. Therefore, this mode is recommended
only when the SF/2 approach is unavailable or there are high-rate
users.
GUI Value Range: D8, D16, D32, D64, D128, D256
Unit: None
Actual Value Range: 8, 16, 32, 64, 128, 256
Default Value: D64

UlSFT B ADD
urnPoi S UCE
nt
C LLC
6 MCF
9 MOD
1 UCE
0 LLC
MCF

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov

Meaning: SF threshold for UEs to start the CM in the uplink in a


cell. When the uplink spreading factor is greater than or equal to
the value of this parameter, the SF/2 mode is preferred.
Otherwise, the high-layer scheduling mode is preferred. The
SF/2 mode consumes more system resources than the high-layer
scheduling mode. Therefore, this mode is recommended only for
low-rate users. The high-layer scheduling mode requires variable
multiplexing positions of transport channels and is applicable to
a relatively narrow range. In addition, this approach affects the
transmission rate of users. Therefore, this mode is recommended
only when the SF/2 approach is unavailable or there are high-rate
users.
GUI Value Range: D8, D16, D32, D64, D128, D256
Unit: None

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

erag Actual Value Range: 8, 16, 32, 64, 128, 256


e
Default Value: D64
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
InterF
reqRA
TSwit
ch

B
S
C
6
9
0
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er

Meaning: RAT type of the measured neighboring cell during a


coverage-based handover when inter-frequency and inter-RAT
neighboring cells are configured. When INTERFREQ is
selected, only inter-frequency neighboring cells are measured
and inter-frequency handover is performed. When INTERRAT is
selected, only neighboring GSM cells are measured and interRAT handover is performed. When SIMINTERFREQRAT is
selected, both inter-frequency and inter-RAT cells are measured,
and the handover is performed according to the type of the cell
that first meets the handover decision criteria. This parameter
does not affect measurements or handovers towards a
neighboring LTE cell.
GUI Value Range: INTERFREQ(inter-frequency handover
only), INTERRAT(inter-RAT handover only),
SIMINTERFREQRAT(inter-frequency and inter-RAT handover)
Unit: None
Actual Value Range: INTERFREQ, INTERRAT,
SIMINTERFREQRAT
Default Value: SIMINTERFREQRAT(inter-frequency and interRAT handover)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
on
Cov
erag
e
InterF
reqRA
TSwit
ch

B
S
C
6
9
1
0

ADD
UCE
LLH
OCO
MM
MOD
UCE
LLH
OCO
MM

InterF B ADD
reqMe S UCE

W
RF
D02
03
02
W
RF
D02
03
03

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: RAT type of the measured neighboring cell during a


coverage-based handover when inter-frequency and inter-RAT
neighboring cells are configured. When INTERFREQ is
selected, only inter-frequency neighboring cells are measured
and inter-frequency handover is performed. When INTERRAT is
selected, only neighboring GSM cells are measured and interRAT handover is performed. When SIMINTERFREQRAT is
selected, both inter-frequency and inter-RAT cells are measured,
and the handover is performed according to the type of the cell
that first meets the handover decision criteria. This parameter
does not affect measurements or handovers towards a
neighboring LTE cell.
GUI Value Range: INTERFREQ(inter-frequency handover
only), INTERRAT(inter-RAT handover only),
SIMINTERFREQRAT(inter-frequency and inter-RAT handover)
Unit: None
Actual Value Range: INTERFREQ, INTERRAT,
SIMINTERFREQRAT
Default Value: SIMINTERFREQRAT(inter-frequency and interRAT handover)

W Inte Meaning: Length of the timer for the inter-frequency


RF r
measurement. If the inter-frequency handover is not performed

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
asTim C LLIN
e
6 TERF
9 REQ
0 HOC
0 OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

D02
03
02
W
RF
D02
03
04
W
RF
D02
12
00

Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur

Description

before this timer expires, the inter-frequency measurement is


stopped and the compression mode is disabled (if enabled
before). The value 0 indicates that this timer is not to be started.
This parameter is used to prevent the long duration of the interfrequency measurement state (compression mode) due to
unavailability of a target cell that meets the handover criteria.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 60

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

e)
InterF
reqMe
asTim
e

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HOC
OV
MOD
UCE
LLIN
TERF
REQ
HOC
OV

W
RF
D02
03
02
W
RF
D02
03
04
W
RF
D02
12
00

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
HC
S
(Hi
erar
chic

Meaning: Length of the timer for the inter-frequency


measurement. If the inter-frequency handover is not performed
before this timer expires, the inter-frequency measurement is
stopped and the compression mode is disabled (if enabled
before). The value 0 indicates that this timer is not to be started.
This parameter is used to prevent the long duration of the interfrequency measurement state (compression mode) due to
unavailability of a target cell that meets the handover criteria.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 60

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

al
Cell
Stru
ctur
e)
InterF
reqMe
asTim
e

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERF
REQ
HON
COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03
W
RF
D02
03
02
W
RF
D02
03
04
W
RF
D02
12
00

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d

Meaning: Length of the timer for the inter-frequency


measurement. If the inter-frequency handover is not performed
before this timer expires, the inter-frequency measurement is
stopped and the compression mode is disabled (if enabled
before). The value 0 indicates that this timer is not to be started.
This parameter is used to prevent the long duration of the interfrequency measurement state (compression mode) due to
unavailability of a target cell that meets the handover criteria.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 15

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Han
dov
er
Bas
ed
on
DL
Qo
S
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)
InterF
reqMe
asTim
e

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERF
REQ
HON
COV
MOD
UCE
LLIN
TERF
REQ
HON
COV

W
RF
D02
01
03
W
RF
D02
03
02
W
RF
D02
03
04
W

Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Inte
r
Fre
que
ncy
Har
d
Han
dov

Meaning: Length of the timer for the inter-frequency


measurement. If the inter-frequency handover is not performed
before this timer expires, the inter-frequency measurement is
stopped and the compression mode is disabled (if enabled
before). The value 0 indicates that this timer is not to be started.
This parameter is used to prevent the long duration of the interfrequency measurement state (compression mode) due to
unavailability of a target cell that meets the handover criteria.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 15

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

InterR
ATMe
asTim
e

B
S
C
6
9

ADD
UCE
LLIN
TERR
ATH

RF
D02
12
00

er
Bas
ed
on
Cov
erag
e
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S
HC
S
(Hi
erar
chic
al
Cell
Stru
ctur
e)

W
RF
D02
03

Inte
rRA
T
Han

Description

Meaning: Length of a timer for inter-RAT measurements. After


the inter-RAT measurement starts, if no inter-RAT handover is
performed when this timer expires, the inter-RAT measurement
is stopped. In addition, the compressed mode (if activated)
should be deactivated. The value 0 indicates that the inter-RAT

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
0 OCO
0 V
MOD
UCE
LLIN
TERR
ATH
OCO
V

09
W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06

dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov

Description

measurement timer is not started.


GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 60

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Bas
ed
on
Loa
d
InterR
ATMe
asTim
e

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
OCO
V
MOD
UCE
LLIN
TERR
ATH
OCO
V

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov

Meaning: Length of a timer for inter-RAT measurements. After


the inter-RAT measurement starts, if no inter-RAT handover is
performed when this timer expires, the inter-RAT measurement
is stopped. In addition, the compressed mode (if activated)
should be deactivated. The value 0 indicates that the inter-RAT
measurement timer is not started.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 60

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d
InterR
ATMe
asTim
e

B
S
C
6
9
0
0

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD
UCE
LLIN
TERR
ATH
ONC
OV

W
RF
D02
03
09
W
RF
D02
03
03
W
RF
D02
03
05
W
RF

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
rRA
T
Han
dov
er

Meaning: Length of a timer for inter-RAT measurements. After


the inter-RAT measurement starts, if no inter-RAT handover is
performed when this timer expires, the inter-RAT measurement
is stopped. In addition, the compressed mode (if activated)
should be deactivated. The value 0 indicates that the inter-RAT
measurement timer is not started.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 15

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

InterR
ATMe
asTim
e

B
S
C
6
9
1
0

ADD
UCE
LLIN
TERR
ATH
ONC
OV
MOD

D02
03
06

Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

W
RF
D02
03
09
W
RF

Inte
rRA
T
Han
dov
er
Bas

Description

Meaning: Length of a timer for inter-RAT measurements. After


the inter-RAT measurement starts, if no inter-RAT handover is
performed when this timer expires, the inter-RAT measurement
is stopped. In addition, the compressed mode (if activated)
should be deactivated. The value 0 indicates that the inter-RAT
measurement timer is not started.
GUI Value Range: 0~512
Unit: s

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
UCE
LLIN
TERR
ATH
ONC
OV

D02
03
03
W
RF
D02
03
05
W
RF
D02
03
06

Description

ed Actual Value Range: 0~512


on Default Value: 15
DL
Qo
S
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Ser
vice
Inte
rRA
T
Han
dov
er
Bas
ed

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on
Loa
d
DLQo
sMcTi
merLe
n

B
S
C
6
9
0
0

ADD
UCE
LLQ
OSH
O
MOD
UCE
LLQ
OSH
O

W
RF
D02
03
09
W
RF
D02
03
04

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

Meaning: Timer length for downlink QoS measurement. This


parameter controls the time lengths for the inter-frequency and
inter-RAT measurement based on QoS. After inter-frequency or
inter-RAT measurement starts, if no inter-frequency handover is
performed when this timer expires, the measurement is stopped,
and the compressed mode is deactivated, if any. If this parameter
is set to 0, this indicates that the timer will not be started. For the
inter-frequency or inter-RAT measurement based on coverage,
the compressed mode can be stopped through reporting event 2F.
For measurement that is not based on coverage, event 2F is not
reported, and the timer must be set but should not be set to 0. As
for the impact on network performance: It reduces the influence
of long time compressed mode to the serving cell. The
compressed mode may be stopped ahead of time, which can
cause the result that the UE fails to initiate inter-frequency or
inter-RAT handover, and thus can lead to call drops.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 20

DLQo
sMcTi
merLe
n

B
S
C
6
9

ADD
UCE
LLQ
OSH
O

W
RF
D02
03

Inte
rRA
T
Han

Meaning: Timer length for downlink QoS measurement. This


parameter controls the time lengths for the inter-frequency and
inter-RAT measurement based on QoS. After inter-frequency or
inter-RAT measurement starts, if no inter-frequency handover is
performed when this timer expires, the measurement is stopped,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

ULQo
sMcTi
merLe
n

Description

1 MOD 09
0 UCE W
LLQ RF
OSH DO
02
03
04

dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

and the compressed mode is deactivated, if any. If this parameter


is set to 0, this indicates that the timer will not be started. For the
inter-frequency or inter-RAT measurement based on coverage,
the compressed mode can be stopped through reporting event 2F.
For measurement that is not based on coverage, event 2F is not
reported, and the timer must be set but should not be set to 0. As
for the impact on network performance: It reduces the influence
of long time compressed mode to the serving cell. The
compressed mode may be stopped ahead of time, which can
cause the result that the UE fails to initiate inter-frequency or
inter-RAT handover, and thus can lead to call drops.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 20

B
S
C
6
9
0
0

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte

Meaning: Timer length for uplink QoS measurement. This


parameter controls the time lengths for the inter-frequency and
inter-RAT measurement based on Qos. After inter-frequency or
inter-RAT measurement starts, if no inter-frequency handover is
performed when this timer expires, the measurement is stopped,
and the compressed mode is deactivated, if any. If this parameter
is set to 0, this indicates that the timer will not be started. For the
inter-frequency or inter-RAT measurement based on coverage,
the compressed mode can be stopped through reporting event 2F.
For measurement that is not based on coverage, event 2F is not
reported, and the timer must be set but should not be set to 0. As
for the impact on network performance: It reduces the influence
of long time compressed mode to the serving cell. The
compressed mode may be stopped ahead of time, which can

ADD
UCE
LLQ
OSH
O
MOD
UCE
LLQ
OSH
O

W
RF
D02
03
09
W
RF
D02
03
04

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

ULQo
sMcTi
merLe
n

B
S
C
6
9
1
0

ADD
UCE
LLQ
OSH
O
MOD
UCE
LLQ
OSH
O

W
RF
D02
03
09
W
RF
D02
03
04

Description

r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
DL
Qo
S

cause the result that the UE fails to initiate inter-frequency or


inter-RAT handover, and thus can lead to call drops.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 20

Inte
rRA
T
Han
dov
er
Bas
ed
on
DL
Qo
S
Inte
r
Fre
que
ncy
Har
d
Han
dov
er

Meaning: Timer length for uplink QoS measurement. This


parameter controls the time lengths for the inter-frequency and
inter-RAT measurement based on Qos. After inter-frequency or
inter-RAT measurement starts, if no inter-frequency handover is
performed when this timer expires, the measurement is stopped,
and the compressed mode is deactivated, if any. If this parameter
is set to 0, this indicates that the timer will not be started. For the
inter-frequency or inter-RAT measurement based on coverage,
the compressed mode can be stopped through reporting event 2F.
For measurement that is not based on coverage, event 2F is not
reported, and the timer must be set but should not be set to 0. As
for the impact on network performance: It reduces the influence
of long time compressed mode to the serving cell. The
compressed mode may be stopped ahead of time, which can
cause the result that the UE fails to initiate inter-frequency or
inter-RAT handover, and thus can lead to call drops.
GUI Value Range: 0~512
Unit: s
Actual Value Range: 0~512
Default Value: 20

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Bas
ed
on
DL
Qo
S
Optim
ization
Switc
h4

B
S
C
6
9
0
0

SET No Non
URR ne e
CTRL
SWIT
CH

Meaning:
1)RB_RLREEST_AM_TRB_RLC_REEST_SWITCH(Reestabli
sh TRB RLC in AM for RL Reestablish) When radio link (RL)
reestablishment is triggered during RB related procedures, the
encryption parameters configured for the RNC become
inconsistent with those configured for the UE if the following
conditions are met: The RB related procedure succeeds; the TRB
is in acknowledged mode (AM) or the size of the RLC PDU
changes in AM; the RLC entity is not reestablished for the TRB.
As a result, data transmission fails on the user plane, and the
TRB is reset. This parameter specifies whether the RNC
reestablishes the RLC entity for TRBs that use AM in the
preceding scenario. 1: This switch is turned on. The RLC entity
is reestablished for the TRB in the preceding scenario. 0: This
switch is turned off. The RLC entity is not reestablished for the
TRB in the preceding scenario.
2)RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH(
Optimize RL Reestablishment for UM TRB) When RL
reestablishment is triggered during an RB setup procedure in
unacknowledged mode (UM), the encryption parameters for the
RNC and UE cannot be reconfigured. As a result, after the RL is
reestablished, data transmission fails on the user plane because
the encryption parameters configured for the RNC are
inconsistent with those configured for the UE. Services are
interrupted. This parameter specifies whether the RNC
reestablishes the RL for TRBs that use UM in the preceding
scenario. 1: This switch is turned on. If the TRB has been
established for the UE, RL reestablishment is not performed in
the preceding scenario even if its trigger conditions are met. 0:
This switch is turned off. RL reestablishment is performed in the
preceding scenario when its trigger conditions are met.
3)DRNC_RL_REEST_OPT_SWITCH(DRNC RL

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Reestablishment Optimization Switch) Whether the RNC


receives a complete message from the UE during radio link (RL)
reestablishment over the Iur interface. 1: This switch is turned
on. The RNC receives a complete message from the UE in the
preceding scenario. 0: This switch is turned off. The RNC does
not receive a complete message from the UE in the preceding
scenario.
4)URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH
Whether the RAN processes a cell update procedure caused by
cell reselection, periodic cell update, UE re-entering service area,
or an RLC unrecoverable error during a state transition from
URA_PCH to CELL_FACH. 1: This switch is turned on. The
RAN processes the cell update procedure during a state
transition from URA_PCH to CELL_FACH. 0: This switch is
turned off. The RAN determines that the cell update procedure is
abnormally triggered and therefore does not process the
procedure. As a result, the cell update procedure times out, and
the UE's connection is abnormally released, increasing the call
drop rate. 5)RB_SETUP_F2D_USE_AM_RLC_SWITCH
Whether the RNC sends a RADIO BEARER SETUP message in
AM to a UE in the CELL_FACH state. 1: This switch is turned
on. The RNC sends a RADIO BEARER SETUP message in AM
to a UE in the CELL_FACH state. Therefore, those UEs that
cannot receive this message in UM can now correctly receive
this message. 0: This switch is turned off. The RNC sends a
RADIO BEARER SETUP message in UM to a UE in the
CELL_FACH state.
6)RB_RECFG_D2F_USE_AM_RLC_SWITCH Whether the
RNC sends a RADIO BEARER RECONFIGURATION message
in AM to a UE that is transitioning from the CELL_DCH state to
the CELL_FACH state. 1: This switch is turned on. The RNC
sends a RADIO BEARER RECONFIGURATION message in
AM to a UE that is transitioning from the CELL_DCH state to
the CELL_FACH state. Therefore, those UEs that cannot receive
this message in UM can now correctly receive this message. 0:
This switch is turned off. The RNC sends a RADIO BEARER
RECONFIGURATION message in UM to a UE that is
transitioning from the CELL_DCH state to the CELL_FACH
state. 7)RB_RECFG_F2D_USE_AM_RLC_SWITCH Whether

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

the RNC sends a RADIO BEARER RECONFIGURATION


message in AM to a UE that is transitioning from the
CELL_FACH state to the CELL_DCH state. 1: This switch is
turned on. The RNC sends a RADIO BEARER
RECONFIGURATION message in AM to a UE that is
transitioning from the CELL_FACH state to the CELL_DCH
state. Therefore, those UEs that cannot receive this message in
UM can now correctly receive this message. 0: This switch is
turned off. The RNC sends a RADIO BEARER
RECONFIGURATION message in UM to a UE that is
transitioning from the CELL_FACH state to the CELL_DCH
state. 8)RRC_UE_USER_SMOOTH_OPT_SWITCH Whether
the RNC corrects the values of the VS.CellDCHUEs.RNC and
VS.CellFACHUEs.RNC counters when performing smooth
operations at 3:00 a.m.. 1: This switch is turned on. The RNC
corrects the values of the VS.CellDCHUEs.RNC and
VS.CellFACHUEs.RNC counters when performing smooth
operations at 3:00 a.m.. That is, the RNC does not calculate the
number of UEs that are processing a signaling procedure into
these two counters. 0: This switch is turned off. The RNC
calculates the number of UEs that are processing a signaling
procedure into these two counters when performing smooth
operations at 3:00 a.m.. The RNC calculates the number of these
UEs into these two counters again after their signaling
procedures are complete. 9)TRNC_LOAD_CTRL_SWITCH
Whether to enable load sharing for the SRNS relocations and
incoming Inter-RAT handover procedure. 1: This switch is
turned on. During an SRNS relocation and incoming Inter-RAT
handover procedure, the signaling and SCCP are processed by
the same signaling subsystem, and load sharing is implemented
between signaling subsystems. 0: This switch is turned off.
During an SRNS relocation and incoming Inter-RAT handover
procedure, the signaling is processed by the signaling subsystem
that carries the serving cell.
10)IU_SIG_REL_PCH_PAGING_SWITCH(Page UEs When
UEs Release Its CS/PS Connection) Whether the RNC sends
paging messages to UEs in the CELL_PCH and URA_PCH
states when these UEs are releasing their connections in the CS
or PS domain. 1: This switch is turned on. The RNC sends

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

paging messages to UEs in the CELL_PCH and URA_PCH


states when these UEs are releasing their connections in the CS
or PS domain. 0: This switch is turned off. The RNC does not
send paging messages to UEs in the CELL_PCH and URA_PCH
states when these UEs are releasing their connections in the CS
or PS domain. 11)CPC_OPT_FOR_RLSETUP_SWITCH(CPC
Configuration Optimization Switch During RL Setup) Whether
the CPC is configured in an optimized way during radio link
(RL) setup. 1: This switch is set to on. The CPC is configured in
an optimized way during RL setup. That is, if the RL activation
time is carried, the RNC forwards the RL activation time to the
NodeB during RL setup. If the RL activation time is not carried,
the RNC changes the Enabling Delay to 128. 0: This switch is set
to off. The CPC is not configured in an optimized way. That is,
the RNC neither forwards the RL activation time to the NodeB
during RL setup nor changes the Enabling Delay. 12)
D2P_L2DEACT_FAIL_OPT_SWITCH (Optimization Switch
for L2 Deactivation Failure During D2P) Whether to release the
RRC connection after an L2 deactivation failure during the D2P
state transition. This switch is set to off by default. 0: This switch
is turned off. The RRC connection is released after an L2
deactivation failure. 1: This switch is turned on. The RRC
connection is not released after an L2 deactivation failure. The
UE stays in the CELL_PCH or URA_PCH state, and the
dedicated channel is released.
13)EFACH_RRC_REG_CMP_SWITCH(E-FACH RRC
Registration Compatibility Switch) Whether special UEs use the
E-FACH to carry their RRC CONNECTION SETUP messages
when the cell is enabled with E-FACH. 1: This switch is set to
on. the RNC retransmits the last RRC CONNECTION SETUP
message on the E-FACH if special users do not respond to the
RRC CONNECTION SETUP message on the FACH. If the UE
returns an RRC CONNECTION SETUP CMP message, the UE
stays in the CELL_DCH state during data transmission. 0: This
switch is set to off. no special processing is performed on special
users. 14) P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH
(Discard Responses with Incorrect TRANSCIDs from UEs
During P2D) Whether the RNC discards a RADIO BEARER
RECONFIGURATION COMPLETE message received from a

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

UE during P2D state transitions when the value of the "RRC


transaction identifier" IE in the message is incorrect. 1: This
switch is set to on. The RNC discards the message and waits for
the UE's response. 0: This switch is set to off. The RNC rolls
back the P2D state transition procedure. 15)
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH (HHO
Rollback Switch for 12.2K AMR Services with AMRC Enabled)
Whether the RNC performs rollback after 12.2 kbit/s AMR-NB
services experience hard handover failures in the scenario where
the narrowband AMRC function takes effect. 0: This switch is
set to off. The RNC does not perform rollback after 12.2 kbit/s
AMR-NB services experience hard handover failures in the
preceding scenario. 1: This switch is set to on. The RNC
performs rollback after 12.2 kbit/s AMR-NB services experience
hard handover failures in the preceding scenario.
16)RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH
Whether the RNC allocates RG combination indexes to radio
links (RLs) for UEs in the CELL_DCH state during UE-notinvolved relocations. 1: This switch is turned on. The RNC
allocates RG combination indexes only to the RLs on the E-DCH
for UEs in the CELL_DCH state during UE-not-involved
relocations. 0: This switch is turned off. The RNC allocates RG
combination indexes to all RLs for UEs in the CELL_DCH state
during UE-not-involved relocations.
17)SCM_CU_CROSS_SWITCH(Support Concurrence of CM
and Cell Update) Whether the RNC supports the concurrence of
the compressed mode (CM) procedure and the cell update
procedure. 1: This switch is set to on. The RNC rolls back the
CM procedure and then processes the cell update message. 0:
This switch is set to off. The RNC does not support the
concurrence of the CM procedure and the cell update procedure.
18)DRNC_HSPA_CM_OPT_SWITCH(Optimize Procedures for
HSPA UEs in CM Under the DRNC) Whether to solve the
problem that the radio link reconfiguration reinitiated by the
SRNC over the Iur interface fails after the DRNC receives a
RADIO LINK RECONFIGURATION PREPARE message
(which carries the Transmission Gap Pattern Sequence
Information and HS-DSCH FDD Information IEs) over the Iur
interface. 1: This switch is set to on. the radio link

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

reconfiguration reinitiated by the SRNC over the Iur interface is


successful after the DRNC receives the preceding RADIO LINK
RECONFIGURATION PREPARE message over the Iur
interface. 0: This switch is set to off, the radio link
reconfiguration reinitiated by the SRNC over the Iur interface
fails after the DRNC receives the preceding RADIO LINK
RECONFIGURATION PREPARE message over the Iur
interface. 19)IUB_TRANSID_OPT_SWITCH(Optimize
TransID Allocation for Iub Messages) Whether the RNC
allocates TransIDs to Iub interface messages in an optimized
way. 1: This switch is set to on. the RNC allocates TransIDs
independently to each NodeB to prevent the message out-oforder problem caused by NodeBs' responses carrying the same
TransID. 0: This switch is set to off. the RNC allocates a set of
TransIDs to the Iub interface messages for all NodeBs.
20)L2_ENHENCE_RECFG_OPT_SWITCH Whether the RNC
correctly reconfigures the parameters related to the enhanced L2
feature in the following scenario: The UE has established a
service and the service uses the enhanced L2 feature; the UE
initiates a second service and the second service experiences a
cell update failure during its setup and is rolled back. When this
switch is set to on, the RNC correctly configures the parameters
related to the enhanced L2 feature and correctly processes the
service setup and cell update rollback in the preceding scenario.
When this switch is set to off, the RNC cannot correctly
configure the parameters related to the enhanced L2 feature, and
consequently call drops occur.
21)ASYN_RL_REEST_OPT_SWITCH Radio link (RL)
reestablishment optimization switch for the scenario where the
following functions are enabled: RB fast setup function for RB
setups accompanied by DRDs with unchanged SRBs, and hard
handover fast reconfiguration. When this switch is set to on, the
RNC determines whether a new RL is synchronized and whether
the CELL UPDATE message carries the reconfiguration tag. If
the RL is not synchronized and the CELL UPDATE message
does not carry the reconfiguration tag, the RL is reestablished.
When this switch is set to off, the trigger conditions of RL
reestablishment remain unchanged.
22)RNC_IMSI_HO_OPT_SWITCH(IMSI-based Handover

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Optimization Switch) Whether the IMSI-based handover feature


takes effect in multioperator core network (MOCN) scenarios. 1:
This switch is set to on. In MOCN scenarios, the RNC releases
the connections of the UEs using a certain international mobile
subscriber identity (IMSI) after receiving a COMMON ID
message from the CN. 0: This switch is set to off. In MOCN
scenarios, the RNC does not release the connections of the UEs
using a certain IMSI after receiving a COMMON ID message
from the CN.
23)IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH(Opt
imize the priorityQueue-Info-to-Modify IE in RADIO LINK
RECONFIGURATION PREPARE Messages over Iur) Whether
the RADIO LINK RECONFIGURATION PREPARE message
over the Iur interface carries the MAChsGuaranteedBitRate or
DiscardTimer field in the priorityQueue-Info-to-Modify IE when
the field will remain unchanged after the reconfiguration. 1: This
switch is set to on. the RADIO LINK RECONFIGURATION
PREPARE message over the Iur interface carries the
MAChsGuaranteedBitRate or DiscardTimer field in the
priorityQueue-Info-to-Modify IE when the field will remain
unchanged after the reconfiguration. In this case, the DRNC can
successfully reinitiate a relocation process after a UE of Release
6 and earlier versions whose SRB is carried on an HSDPA
channel is relocated to the DRNC. 0: This switch is set to off. the
RADIO LINK RECONFIGURATION PREPARE message over
the Iur interface does not carry the priorityQueue-Info-to-Modify
IE when MAChsGuaranteedBitRate and DiscardTimer remain
unchanged after the reconfiguration. In this case, a UE of
Release 6 and earlier versions whose SRB is carried on an
HSDPA channel fails to reinitiate a relocation process after being
relocated to the DRNC.
24)URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH (No
Paging Switch for LAC or SAC Change During URA Update)
Whether paging is performed when the location area code (LAC)
or service area code (SAC) of the target cell differs from that of
the source cell during a UTRAN registration area (URA) update.
1: This switch is set to on. Paging is not performed in the
preceding scenario. 0: This switch is set to off. Paging is
performed in the preceding scenario.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

25)PAGING_OVERLAP_CU_OPT_SWITCH(Optimize CS
Paging During Cell Update) Whether the RNC optimizes CS
paging that occurs during a cell update procedure. 1: This switch
is set to on. The RNC optimizes CS paging that occurs during a
cell update procedure. 0: This switch is set to off. The RNC does
not optimize CS paging that occurs during a cell update
procedure, and as a result, the access delay of the CS called
partly is long.
26)SRVCC_RELOC_IN_USE_CS_KEY_SWITCH(SRVCC
Incoming Relocation Using CS CK Switch) Whether UEs that
are processing CS+PS combined services use the CS cipher key
(CK) during an SRVCC incoming relocation. 1: This switch is
set to on. UEs that are processing CS+PS combined services use
the CS CK during an SRVCC incoming relocation. This prevents
relocation failures caused by incorrect CKs. 0: This switch is set
to off. UEs that are processing CS+PS combined services use the
CK of the last released domain during an SRVCC incoming
relocation. If the last released domain is PS, the incoming
relocation fails.
27)SOCKET_RECEIVE_DATA_CORRECT_SWITCH(CBC
Socket Receive Data Length Control Switch) Whether the RNC
correctly processes the messages whose size is greater than 32
kbytes and that are sent by the cell broadcast center (CBC)
server. 1: This switch is set to on. The RNC correctly processes
the messages whose size is greater than 32 Kbytes and that are
sent by the CBC server. 0: This switch is set to off. The RNC
cannot correctly process the messages whose size is greater than
32 kbytes and that are sent by the CBC server.
28)CU_PRI_OVERLAP_OTHER_PROC_SWITCH(Preferential
ly Process Cell Update in Process Overlap) Whether the RNC
preferentially processes the cell update procedure when it
overlaps with other procedures. 1: When this switch is set to on,
the RNC preferentially processes the cell update procedure in the
preceding scenario. 0: When this switch is set to off, the original
processing method is used.
29)INTERRAT2U_INTEG_PROTECT_OPT_SWITCH(Integrit
y Protection Optimization Switch for Incoming Inter-RAT
Handovers) Whether the optimized integrity protection function
is enabled for incoming L2U or G2U inter-RAT handovers. 1:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

This switch is set to on. The integrity protection function is


immediately activated for SRB0 to SRB4 after the incoming
L2U or G2U inter-RAT handover is complete. 0: This switch is
set to off. The integrity protection function is activated only for
SRB2 after the incoming L2U or G2U inter-RAT handover is
complete. The integrity protection for other SRBs (SRB0, SRB1,
SRB3, and SRB4) is activated only after the UE sends a
message.
30)INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH(Optim
ize the Rate upon NodeB RL Change for H Services) Whether
the rate optimization policy is applied in the scenario where the
radio link (RL) for HSPA services changes inside the NodeB. 1:
This switch is set to on. The rate optimization policy is applied in
the scenario where the RL for HSPA services changes inside the
NodeB. 0: This switch is set to off. The rate optimization policy
is not applied in the scenario where the RL for HSPA services
changes inside the NodeB.
31)DRNC_RL_PARA_UPT_OPT_SWITCH(RL Parameter
Update Optimization Switch on RNC) Whether the RL PARA
UPT IND message over the Iur interface can be correctly
processed. 1: This switch is set to on. The RL PARA UPT IND
message over the Iur interface can be correctly processed. 0: This
switch is set to off. The RL PARA UPT IND message over the
Iur interface cannot be correctly processed.
GUI Value Range:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH,
RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH,
DRNC_RL_REEST_OPT_SWITCH,
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH,
RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH,
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH,
PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH,
DRNC_RL_PARA_UPT_OPT_SWITCH
Unit: None
Actual Value Range:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH,
RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH,
DRNC_RL_REEST_OPT_SWITCH,
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH,
RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH,
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH,
PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH,
DRNC_RL_PARA_UPT_OPT_SWITCH
Default Value:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH:0,RB_SET
UP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH:0,DRNC_R
L_REEST_OPT_SWITCH:1,URA2FACH_OVERLAP_CELLU
PT_PROC_SWITCH:0,RB_SETUP_F2D_USE_AM_RLC_SWI
TCH:0,RB_RECFG_D2F_USE_AM_RLC_SWITCH:0,RB_RE
CFG_F2D_USE_AM_RLC_SWITCH:0,RRC_UE_USER_SMO
OTH_OPT_SWITCH:1,TRNC_LOAD_CTRL_SWITCH:0,IU_
SIG_REL_PCH_PAGING_SWITCH:0,CPC_OPT_FOR_RLSE
TUP_SWITCH:1,D2P_L2DEACT_FAIL_OPT_SWITCH:0,EF
ACH_RRC_REG_CMP_SWITCH:0,P2D_TSID_ERR_UE_RSP
_MSG_DISCD_SWITCH:0,AMRC_ON_122_AMR_HHO_RO
LL_BACK_SWITCH:0,RELOC_IN_RG_COMB_INDEX_ALL
OC_SWITCH:0,SCM_CU_CROSS_SWITCH:0,DRNC_HSPA_
CM_OPT_SWITCH:0,IUB_TRANSID_OPT_SWITCH:0,L2_E
NHENCE_RECFG_OPT_SWITCH:0,ASYN_RL_REEST_OPT
_SWITCH:0,RNC_IMSI_HO_OPT_SWITCH:0,IUR_PRIQUE
UE_INFO_TO_MODIFY_OPT_SWITCH:0,URA_PCH_LAC_
RAC_CHG_NO_PAGING_SWITCH:0,PAGING_OVERLAP_C
U_OPT_SWITCH:0,SRVCC_RELOC_IN_USE_CS_KEY_SWI
TCH:1,SOCKET_RECEIVE_DATA_CORRECT_SWITCH:1,C
U_PRI_OVERLAP_OTHER_PROC_SWITCH:0,INTERRAT2
U_INTEG_PROTECT_OPT_SWITCH:0,INTRA_NODEB_RL
CC_INIT_CAP_OPT_SWITCH:0,DRNC_RL_PARA_UPT_OP
T_SWITCH:1
Optim B SET
ization S URR

No Non Meaning:
ne e
1)RB_RLREEST_AM_TRB_RLC_REEST_SWITCH(Reestabli

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Switc
h4

C CTRL
6 SWIT
9 CH
1
0

Description

sh TRB RLC in AM for RL Reestablish) When radio link (RL)


reestablishment is triggered during RB related procedures, the
encryption parameters configured for the RNC become
inconsistent with those configured for the UE if the following
conditions are met: The RB related procedure succeeds; the TRB
is in acknowledged mode (AM) or the size of the RLC PDU
changes in AM; the RLC entity is not reestablished for the TRB.
As a result, data transmission fails on the user plane, and the
TRB is reset. This parameter specifies whether the RNC
reestablishes the RLC entity for TRBs that use AM in the
preceding scenario. 1: This switch is turned on. The RLC entity
is reestablished for the TRB in the preceding scenario. 0: This
switch is turned off. The RLC entity is not reestablished for the
TRB in the preceding scenario.
2)RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH(
Optimize RL Reestablishment for UM TRB) When RL
reestablishment is triggered during an RB setup procedure in
unacknowledged mode (UM), the encryption parameters for the
RNC and UE cannot be reconfigured. As a result, after the RL is
reestablished, data transmission fails on the user plane because
the encryption parameters configured for the RNC are
inconsistent with those configured for the UE. Services are
interrupted. This parameter specifies whether the RNC
reestablishes the RL for TRBs that use UM in the preceding
scenario. 1: This switch is turned on. If the TRB has been
established for the UE, RL reestablishment is not performed in
the preceding scenario even if its trigger conditions are met. 0:
This switch is turned off. RL reestablishment is performed in the
preceding scenario when its trigger conditions are met.
3)DRNC_RL_REEST_OPT_SWITCH(DRNC RL
Reestablishment Optimization Switch) Whether the RNC
receives a complete message from the UE during radio link (RL)
reestablishment over the Iur interface. 1: This switch is turned
on. The RNC receives a complete message from the UE in the
preceding scenario. 0: This switch is turned off. The RNC does
not receive a complete message from the UE in the preceding
scenario.
4)URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH
Whether the RAN processes a cell update procedure caused by

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

cell reselection, periodic cell update, UE re-entering service area,


or an RLC unrecoverable error during a state transition from
URA_PCH to CELL_FACH. 1: This switch is turned on. The
RAN processes the cell update procedure during a state
transition from URA_PCH to CELL_FACH. 0: This switch is
turned off. The RAN determines that the cell update procedure is
abnormally triggered and therefore does not process the
procedure. As a result, the cell update procedure times out, and
the UE's connection is abnormally released, increasing the call
drop rate. 5)RB_SETUP_F2D_USE_AM_RLC_SWITCH
Whether the RNC sends a RADIO BEARER SETUP message in
AM to a UE in the CELL_FACH state. 1: This switch is turned
on. The RNC sends a RADIO BEARER SETUP message in AM
to a UE in the CELL_FACH state. Therefore, those UEs that
cannot receive this message in UM can now correctly receive
this message. 0: This switch is turned off. The RNC sends a
RADIO BEARER SETUP message in UM to a UE in the
CELL_FACH state.
6)RB_RECFG_D2F_USE_AM_RLC_SWITCH Whether the
RNC sends a RADIO BEARER RECONFIGURATION message
in AM to a UE that is transitioning from the CELL_DCH state to
the CELL_FACH state. 1: This switch is turned on. The RNC
sends a RADIO BEARER RECONFIGURATION message in
AM to a UE that is transitioning from the CELL_DCH state to
the CELL_FACH state. Therefore, those UEs that cannot receive
this message in UM can now correctly receive this message. 0:
This switch is turned off. The RNC sends a RADIO BEARER
RECONFIGURATION message in UM to a UE that is
transitioning from the CELL_DCH state to the CELL_FACH
state. 7)RB_RECFG_F2D_USE_AM_RLC_SWITCH Whether
the RNC sends a RADIO BEARER RECONFIGURATION
message in AM to a UE that is transitioning from the
CELL_FACH state to the CELL_DCH state. 1: This switch is
turned on. The RNC sends a RADIO BEARER
RECONFIGURATION message in AM to a UE that is
transitioning from the CELL_FACH state to the CELL_DCH
state. Therefore, those UEs that cannot receive this message in
UM can now correctly receive this message. 0: This switch is
turned off. The RNC sends a RADIO BEARER

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RECONFIGURATION message in UM to a UE that is


transitioning from the CELL_FACH state to the CELL_DCH
state. 8)RRC_UE_USER_SMOOTH_OPT_SWITCH Whether
the RNC corrects the values of the VS.CellDCHUEs.RNC and
VS.CellFACHUEs.RNC counters when performing smooth
operations at 3:00 a.m.. 1: This switch is turned on. The RNC
corrects the values of the VS.CellDCHUEs.RNC and
VS.CellFACHUEs.RNC counters when performing smooth
operations at 3:00 a.m.. That is, the RNC does not calculate the
number of UEs that are processing a signaling procedure into
these two counters. 0: This switch is turned off. The RNC
calculates the number of UEs that are processing a signaling
procedure into these two counters when performing smooth
operations at 3:00 a.m.. The RNC calculates the number of these
UEs into these two counters again after their signaling
procedures are complete. 9)TRNC_LOAD_CTRL_SWITCH
Whether to enable load sharing for the SRNS relocations and
incoming Inter-RAT handover procedure. 1: This switch is
turned on. During an SRNS relocation and incoming Inter-RAT
handover procedure, the signaling and SCCP are processed by
the same signaling subsystem, and load sharing is implemented
between signaling subsystems. 0: This switch is turned off.
During an SRNS relocation and incoming Inter-RAT handover
procedure, the signaling is processed by the signaling subsystem
that carries the serving cell.
10)IU_SIG_REL_PCH_PAGING_SWITCH(Page UEs When
UEs Release Its CS/PS Connection) Whether the RNC sends
paging messages to UEs in the CELL_PCH and URA_PCH
states when these UEs are releasing their connections in the CS
or PS domain. 1: This switch is turned on. The RNC sends
paging messages to UEs in the CELL_PCH and URA_PCH
states when these UEs are releasing their connections in the CS
or PS domain. 0: This switch is turned off. The RNC does not
send paging messages to UEs in the CELL_PCH and URA_PCH
states when these UEs are releasing their connections in the CS
or PS domain. 11)CPC_OPT_FOR_RLSETUP_SWITCH(CPC
Configuration Optimization Switch During RL Setup) Whether
the CPC is configured in an optimized way during radio link
(RL) setup. 1: This switch is set to on. The CPC is configured in

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

an optimized way during RL setup. That is, if the RL activation


time is carried, the RNC forwards the RL activation time to the
NodeB during RL setup. If the RL activation time is not carried,
the RNC changes the Enabling Delay to 128. 0: This switch is set
to off. The CPC is not configured in an optimized way. That is,
the RNC neither forwards the RL activation time to the NodeB
during RL setup nor changes the Enabling Delay. 12)
D2P_L2DEACT_FAIL_OPT_SWITCH (Optimization Switch
for L2 Deactivation Failure During D2P) Whether to release the
RRC connection after an L2 deactivation failure during the D2P
state transition. This switch is set to off by default. 0: This switch
is turned off. The RRC connection is released after an L2
deactivation failure. 1: This switch is turned on. The RRC
connection is not released after an L2 deactivation failure. The
UE stays in the CELL_PCH or URA_PCH state, and the
dedicated channel is released.
13)EFACH_RRC_REG_CMP_SWITCH(E-FACH RRC
Registration Compatibility Switch) Whether special UEs use the
E-FACH to carry their RRC CONNECTION SETUP messages
when the cell is enabled with E-FACH. 1: This switch is set to
on. the RNC retransmits the last RRC CONNECTION SETUP
message on the E-FACH if special users do not respond to the
RRC CONNECTION SETUP message on the FACH. If the UE
returns an RRC CONNECTION SETUP CMP message, the UE
stays in the CELL_DCH state during data transmission. 0: This
switch is set to off. no special processing is performed on special
users. 14) P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH
(Discard Responses with Incorrect TRANSCIDs from UEs
During P2D) Whether the RNC discards a RADIO BEARER
RECONFIGURATION COMPLETE message received from a
UE during P2D state transitions when the value of the "RRC
transaction identifier" IE in the message is incorrect. 1: This
switch is set to on. The RNC discards the message and waits for
the UE's response. 0: This switch is set to off. The RNC rolls
back the P2D state transition procedure. 15)
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH (HHO
Rollback Switch for 12.2K AMR Services with AMRC Enabled)
Whether the RNC performs rollback after 12.2 kbit/s AMR-NB
services experience hard handover failures in the scenario where

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

the narrowband AMRC function takes effect. 0: This switch is


set to off. The RNC does not perform rollback after 12.2 kbit/s
AMR-NB services experience hard handover failures in the
preceding scenario. 1: This switch is set to on. The RNC
performs rollback after 12.2 kbit/s AMR-NB services experience
hard handover failures in the preceding scenario.
16)RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH
Whether the RNC allocates RG combination indexes to radio
links (RLs) for UEs in the CELL_DCH state during UE-notinvolved relocations. 1: This switch is turned on. The RNC
allocates RG combination indexes only to the RLs on the E-DCH
for UEs in the CELL_DCH state during UE-not-involved
relocations. 0: This switch is turned off. The RNC allocates RG
combination indexes to all RLs for UEs in the CELL_DCH state
during UE-not-involved relocations.
17)SCM_CU_CROSS_SWITCH(Support Concurrence of CM
and Cell Update) Whether the RNC supports the concurrence of
the compressed mode (CM) procedure and the cell update
procedure. 1: This switch is set to on. The RNC rolls back the
CM procedure and then processes the cell update message. 0:
This switch is set to off. The RNC does not support the
concurrence of the CM procedure and the cell update procedure.
18)DRNC_HSPA_CM_OPT_SWITCH(Optimize Procedures for
HSPA UEs in CM Under the DRNC) Whether to solve the
problem that the radio link reconfiguration reinitiated by the
SRNC over the Iur interface fails after the DRNC receives a
RADIO LINK RECONFIGURATION PREPARE message
(which carries the Transmission Gap Pattern Sequence
Information and HS-DSCH FDD Information IEs) over the Iur
interface. 1: This switch is set to on. the radio link
reconfiguration reinitiated by the SRNC over the Iur interface is
successful after the DRNC receives the preceding RADIO LINK
RECONFIGURATION PREPARE message over the Iur
interface. 0: This switch is set to off, the radio link
reconfiguration reinitiated by the SRNC over the Iur interface
fails after the DRNC receives the preceding RADIO LINK
RECONFIGURATION PREPARE message over the Iur
interface. 19)IUB_TRANSID_OPT_SWITCH(Optimize
TransID Allocation for Iub Messages) Whether the RNC

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

allocates TransIDs to Iub interface messages in an optimized


way. 1: This switch is set to on. the RNC allocates TransIDs
independently to each NodeB to prevent the message out-oforder problem caused by NodeBs' responses carrying the same
TransID. 0: This switch is set to off. the RNC allocates a set of
TransIDs to the Iub interface messages for all NodeBs.
20)L2_ENHENCE_RECFG_OPT_SWITCH Whether the RNC
correctly reconfigures the parameters related to the enhanced L2
feature in the following scenario: The UE has established a
service and the service uses the enhanced L2 feature; the UE
initiates a second service and the second service experiences a
cell update failure during its setup and is rolled back. When this
switch is set to on, the RNC correctly configures the parameters
related to the enhanced L2 feature and correctly processes the
service setup and cell update rollback in the preceding scenario.
When this switch is set to off, the RNC cannot correctly
configure the parameters related to the enhanced L2 feature, and
consequently call drops occur.
21)ASYN_RL_REEST_OPT_SWITCH Radio link (RL)
reestablishment optimization switch for the scenario where the
following functions are enabled: RB fast setup function for RB
setups accompanied by DRDs with unchanged SRBs, and hard
handover fast reconfiguration. When this switch is set to on, the
RNC determines whether a new RL is synchronized and whether
the CELL UPDATE message carries the reconfiguration tag. If
the RL is not synchronized and the CELL UPDATE message
does not carry the reconfiguration tag, the RL is reestablished.
When this switch is set to off, the trigger conditions of RL
reestablishment remain unchanged.
22)RNC_IMSI_HO_OPT_SWITCH(IMSI-based Handover
Optimization Switch) Whether the IMSI-based handover feature
takes effect in multioperator core network (MOCN) scenarios. 1:
This switch is set to on. In MOCN scenarios, the RNC releases
the connections of the UEs using a certain international mobile
subscriber identity (IMSI) after receiving a COMMON ID
message from the CN. 0: This switch is set to off. In MOCN
scenarios, the RNC does not release the connections of the UEs
using a certain IMSI after receiving a COMMON ID message
from the CN.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

23)IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH(Opt
imize the priorityQueue-Info-to-Modify IE in RADIO LINK
RECONFIGURATION PREPARE Messages over Iur) Whether
the RADIO LINK RECONFIGURATION PREPARE message
over the Iur interface carries the MAChsGuaranteedBitRate or
DiscardTimer field in the priorityQueue-Info-to-Modify IE when
the field will remain unchanged after the reconfiguration. 1: This
switch is set to on. the RADIO LINK RECONFIGURATION
PREPARE message over the Iur interface carries the
MAChsGuaranteedBitRate or DiscardTimer field in the
priorityQueue-Info-to-Modify IE when the field will remain
unchanged after the reconfiguration. In this case, the DRNC can
successfully reinitiate a relocation process after a UE of Release
6 and earlier versions whose SRB is carried on an HSDPA
channel is relocated to the DRNC. 0: This switch is set to off. the
RADIO LINK RECONFIGURATION PREPARE message over
the Iur interface does not carry the priorityQueue-Info-to-Modify
IE when MAChsGuaranteedBitRate and DiscardTimer remain
unchanged after the reconfiguration. In this case, a UE of
Release 6 and earlier versions whose SRB is carried on an
HSDPA channel fails to reinitiate a relocation process after being
relocated to the DRNC.
24)URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH (No
Paging Switch for LAC or SAC Change During URA Update)
Whether paging is performed when the location area code (LAC)
or service area code (SAC) of the target cell differs from that of
the source cell during a UTRAN registration area (URA) update.
1: This switch is set to on. Paging is not performed in the
preceding scenario. 0: This switch is set to off. Paging is
performed in the preceding scenario.
25)PAGING_OVERLAP_CU_OPT_SWITCH(Optimize CS
Paging During Cell Update) Whether the RNC optimizes CS
paging that occurs during a cell update procedure. 1: This switch
is set to on. The RNC optimizes CS paging that occurs during a
cell update procedure. 0: This switch is set to off. The RNC does
not optimize CS paging that occurs during a cell update
procedure, and as a result, the access delay of the CS called
partly is long.
26)SRVCC_RELOC_IN_USE_CS_KEY_SWITCH(SRVCC

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Incoming Relocation Using CS CK Switch) Whether UEs that


are processing CS+PS combined services use the CS cipher key
(CK) during an SRVCC incoming relocation. 1: This switch is
set to on. UEs that are processing CS+PS combined services use
the CS CK during an SRVCC incoming relocation. This prevents
relocation failures caused by incorrect CKs. 0: This switch is set
to off. UEs that are processing CS+PS combined services use the
CK of the last released domain during an SRVCC incoming
relocation. If the last released domain is PS, the incoming
relocation fails.
27)SOCKET_RECEIVE_DATA_CORRECT_SWITCH(CBC
Socket Receive Data Length Control Switch) Whether the RNC
correctly processes the messages whose size is greater than 32
kbytes and that are sent by the cell broadcast center (CBC)
server. 1: This switch is set to on. The RNC correctly processes
the messages whose size is greater than 32 Kbytes and that are
sent by the CBC server. 0: This switch is set to off. The RNC
cannot correctly process the messages whose size is greater than
32 kbytes and that are sent by the CBC server.
28)CU_PRI_OVERLAP_OTHER_PROC_SWITCH(Preferential
ly Process Cell Update in Process Overlap) Whether the RNC
preferentially processes the cell update procedure when it
overlaps with other procedures. 1: When this switch is set to on,
the RNC preferentially processes the cell update procedure in the
preceding scenario. 0: When this switch is set to off, the original
processing method is used.
29)INTERRAT2U_INTEG_PROTECT_OPT_SWITCH(Integrit
y Protection Optimization Switch for Incoming Inter-RAT
Handovers) Whether the optimized integrity protection function
is enabled for incoming L2U or G2U inter-RAT handovers. 1:
This switch is set to on. The integrity protection function is
immediately activated for SRB0 to SRB4 after the incoming
L2U or G2U inter-RAT handover is complete. 0: This switch is
set to off. The integrity protection function is activated only for
SRB2 after the incoming L2U or G2U inter-RAT handover is
complete. The integrity protection for other SRBs (SRB0, SRB1,
SRB3, and SRB4) is activated only after the UE sends a
message.
30)INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH(Optim

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

ize the Rate upon NodeB RL Change for H Services) Whether


the rate optimization policy is applied in the scenario where the
radio link (RL) for HSPA services changes inside the NodeB. 1:
This switch is set to on. The rate optimization policy is applied in
the scenario where the RL for HSPA services changes inside the
NodeB. 0: This switch is set to off. The rate optimization policy
is not applied in the scenario where the RL for HSPA services
changes inside the NodeB.
31)DRNC_RL_PARA_UPT_OPT_SWITCH(RL Parameter
Update Optimization Switch on RNC) Whether the RL PARA
UPT IND message over the Iur interface can be correctly
processed. 1: This switch is set to on. The RL PARA UPT IND
message over the Iur interface can be correctly processed. 0: This
switch is set to off. The RL PARA UPT IND message over the
Iur interface cannot be correctly processed.
GUI Value Range:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH,
RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH,
DRNC_RL_REEST_OPT_SWITCH,
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH,
RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH,
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH,
PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,
INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH,
DRNC_RL_PARA_UPT_OPT_SWITCH
Unit: None
Actual Value Range:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH,
RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH,
DRNC_RL_REEST_OPT_SWITCH,
URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH,
RB_SETUP_F2D_USE_AM_RLC_SWITCH,
RB_RECFG_D2F_USE_AM_RLC_SWITCH,
RB_RECFG_F2D_USE_AM_RLC_SWITCH,
RRC_UE_USER_SMOOTH_OPT_SWITCH,
TRNC_LOAD_CTRL_SWITCH,
IU_SIG_REL_PCH_PAGING_SWITCH,
CPC_OPT_FOR_RLSETUP_SWITCH,
D2P_L2DEACT_FAIL_OPT_SWITCH,
EFACH_RRC_REG_CMP_SWITCH,
P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH,
AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH,
RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH,
SCM_CU_CROSS_SWITCH,
DRNC_HSPA_CM_OPT_SWITCH,
IUB_TRANSID_OPT_SWITCH,
L2_ENHENCE_RECFG_OPT_SWITCH,
ASYN_RL_REEST_OPT_SWITCH,
RNC_IMSI_HO_OPT_SWITCH,
IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH,
URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH,
PAGING_OVERLAP_CU_OPT_SWITCH,
SRVCC_RELOC_IN_USE_CS_KEY_SWITCH,
SOCKET_RECEIVE_DATA_CORRECT_SWITCH,
CU_PRI_OVERLAP_OTHER_PROC_SWITCH,
INTERRAT2U_INTEG_PROTECT_OPT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH,
DRNC_RL_PARA_UPT_OPT_SWITCH
Default Value:
RB_RLREEST_AM_TRB_RLC_REEST_SWITCH:0,RB_SET
UP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH:0,DRNC_R
L_REEST_OPT_SWITCH:1,URA2FACH_OVERLAP_CELLU
PT_PROC_SWITCH:0,RB_SETUP_F2D_USE_AM_RLC_SWI
TCH:0,RB_RECFG_D2F_USE_AM_RLC_SWITCH:0,RB_RE
CFG_F2D_USE_AM_RLC_SWITCH:0,RRC_UE_USER_SMO
OTH_OPT_SWITCH:1,TRNC_LOAD_CTRL_SWITCH:0,IU_
SIG_REL_PCH_PAGING_SWITCH:0,CPC_OPT_FOR_RLSE
TUP_SWITCH:1,D2P_L2DEACT_FAIL_OPT_SWITCH:0,EF
ACH_RRC_REG_CMP_SWITCH:0,P2D_TSID_ERR_UE_RSP
_MSG_DISCD_SWITCH:0,AMRC_ON_122_AMR_HHO_RO
LL_BACK_SWITCH:0,RELOC_IN_RG_COMB_INDEX_ALL
OC_SWITCH:0,SCM_CU_CROSS_SWITCH:0,DRNC_HSPA_
CM_OPT_SWITCH:0,IUB_TRANSID_OPT_SWITCH:0,L2_E
NHENCE_RECFG_OPT_SWITCH:0,ASYN_RL_REEST_OPT
_SWITCH:0,RNC_IMSI_HO_OPT_SWITCH:0,IUR_PRIQUE
UE_INFO_TO_MODIFY_OPT_SWITCH:0,URA_PCH_LAC_
RAC_CHG_NO_PAGING_SWITCH:0,PAGING_OVERLAP_C
U_OPT_SWITCH:0,SRVCC_RELOC_IN_USE_CS_KEY_SWI
TCH:1,SOCKET_RECEIVE_DATA_CORRECT_SWITCH:1,C
U_PRI_OVERLAP_OTHER_PROC_SWITCH:0,INTERRAT2
U_INTEG_PROTECT_OPT_SWITCH:0,INTRA_NODEB_RL
CC_INIT_CAP_OPT_SWITCH:0,DRNC_RL_PARA_UPT_OP
T_SWITCH:1
Proces B ADD
sSwitc S UNR
h
C NC
6 MOD
9 UNR
0 NC
0

W
RF
D01
01
01

3G
PP
R9
Spe
cifi
cati
ons

Meaning: Process control switch. 1.


RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH:
After this switch is turned on and when the DRNC receives a
handover/relocation request from the SRNC, the DRNC sends
the SRNC a handover/relocation failure message containing a
special cause value if the target cell is controlled by another
RNC. During the following handovers or relocations, the SRNC
considers the RNC that controls the cell as the target RNC.
When this switch is turned off and when the DRNC receives a
handover/relocation request from the SRNC, the DRNC sends
the SRNC a handover/relocation failure message not containing

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

a special cause value if the target cell is controlled by another


RNC. 2. HSDPA_IE_COMPATIBLE_SWITCH Whether the
values of the "HS-DSCH configured indicator" and "HARQ Info
for E-DCH" IEs contained in a RADIO LINK
RECONFIGURATION PREPARE message are the same as
those contained in a RADIO LINK SETUP REQUEST message
during a cross-Iur handover 1: This switch is turned on. The
SRNC performs compatibility processing. The values of the two
IEs contained in the RADIO LINK RECONFIGURATION
PREPARE message are different from those contained in the
RADIO LINK SETUP REQUEST message. 0: This switch is
turned off. The SRNC does not perform compatibility
processing. The values of the two IEs contained in the RADIO
LINK RECONFIGURATION PREPARE message are the same
as those contained in the RADIO LINK SETUP REQUEST
message. This parameter is an advanced parameter. Therefore,
modify the setting of this parameter under the instruction of
Huawei technical support. 3. NRNC_COMPATIBLE_SWITCH
Whether the configured NRNC needs compatibility processing
1: This switch is set to on. The NRNC needs compatibility
processing. The compatibility processing is performed based on
the settings of PS_0K_STATIC_RELOC_IN_CMP_SWITCH
and ADD_DRL_PS_0K_TO_8K_SWITCH under the
OptimizationSwitch5 parameter in the SET URRCTRLSWITCH
command. 0: This switch is set to off. The NRNC does not need
compatibility processing.
GUI Value Range:
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH(RN
C_NODE_REDUNDANCY_COMPATIBLE_SWITCH),
HSDPA_IE_COMPATIBLE_SWITCH(HSDPA_IE_COMPATIB
LE_SWITCH),
NRNC_COMPATIBLE_SWITCH(NRNC_COMPATIBLE_SWI
TCH)
Unit: None
Actual Value Range:
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH,
HSDPA_IE_COMPATIBLE_SWITCH,
NRNC_COMPATIBLE_SWITCH
Default Value:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH:0,HS
DPA_IE_COMPATIBLE_SWITCH:0,NRNC_COMPATIBLE_S
WITCH:0
Proces B ADD
sSwitc S UNR
h
C NC
6 MOD
9 UNR
1 NC
0

W
RF
D01
01
01

3G
PP
R9
Spe
cifi
cati
ons

Meaning: Process control switch. 1.


RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH:
After this switch is turned on and when the DRNC receives a
handover/relocation request from the SRNC, the DRNC sends
the SRNC a handover/relocation failure message containing a
special cause value if the target cell is controlled by another
RNC. During the following handovers or relocations, the SRNC
considers the RNC that controls the cell as the target RNC.
When this switch is turned off and when the DRNC receives a
handover/relocation request from the SRNC, the DRNC sends
the SRNC a handover/relocation failure message not containing
a special cause value if the target cell is controlled by another
RNC. 2. HSDPA_IE_COMPATIBLE_SWITCH Whether the
values of the "HS-DSCH configured indicator" and "HARQ Info
for E-DCH" IEs contained in a RADIO LINK
RECONFIGURATION PREPARE message are the same as
those contained in a RADIO LINK SETUP REQUEST message
during a cross-Iur handover 1: This switch is turned on. The
SRNC performs compatibility processing. The values of the two
IEs contained in the RADIO LINK RECONFIGURATION
PREPARE message are different from those contained in the
RADIO LINK SETUP REQUEST message. 0: This switch is
turned off. The SRNC does not perform compatibility
processing. The values of the two IEs contained in the RADIO
LINK RECONFIGURATION PREPARE message are the same
as those contained in the RADIO LINK SETUP REQUEST
message. This parameter is an advanced parameter. Therefore,
modify the setting of this parameter under the instruction of
Huawei technical support. 3. NRNC_COMPATIBLE_SWITCH
Whether the configured NRNC needs compatibility processing
1: This switch is set to on. The NRNC needs compatibility
processing. The compatibility processing is performed based on
the settings of PS_0K_STATIC_RELOC_IN_CMP_SWITCH
and ADD_DRL_PS_0K_TO_8K_SWITCH under the
OptimizationSwitch5 parameter in the SET URRCTRLSWITCH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

command. 0: This switch is set to off. The NRNC does not need
compatibility processing.
GUI Value Range:
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH(RN
C_NODE_REDUNDANCY_COMPATIBLE_SWITCH),
HSDPA_IE_COMPATIBLE_SWITCH(HSDPA_IE_COMPATIB
LE_SWITCH),
NRNC_COMPATIBLE_SWITCH(NRNC_COMPATIBLE_SWI
TCH)
Unit: None
Actual Value Range:
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH,
HSDPA_IE_COMPATIBLE_SWITCH,
NRNC_COMPATIBLE_SWITCH
Default Value:
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH:0,HS
DPA_IE_COMPATIBLE_SWITCH:0,NRNC_COMPATIBLE_S
WITCH:0
RsvS B SET No Non
witch5 S UAL ne e
C GOR
6 SVPA
9 RA
0
0

Meaning: RRM algorithm reserved U32 Switch Para 5. The 32bit parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_5_BIT1,
RESERVED_SWITCH_5_BIT2,
RESERVED_SWITCH_5_BIT3,
RESERVED_SWITCH_5_BIT4,
RESERVED_SWITCH_5_BIT5,
RESERVED_SWITCH_5_BIT6,
RESERVED_SWITCH_5_BIT7,
RESERVED_SWITCH_5_BIT8,
RESERVED_SWITCH_5_BIT9,
RESERVED_SWITCH_5_BIT10,
RESERVED_SWITCH_5_BIT11,
RESERVED_SWITCH_5_BIT12,
RESERVED_SWITCH_5_BIT13,
RESERVED_SWITCH_5_BIT14,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_5_BIT15,
RESERVED_SWITCH_5_BIT16,
RESERVED_SWITCH_5_BIT17,
RESERVED_SWITCH_5_BIT18,
RESERVED_SWITCH_5_BIT19,
RESERVED_SWITCH_5_BIT20,
RESERVED_SWITCH_5_BIT21,
RESERVED_SWITCH_5_BIT22,
RESERVED_SWITCH_5_BIT23,
RESERVED_SWITCH_5_BIT24,
RESERVED_SWITCH_5_BIT25,
RESERVED_SWITCH_5_BIT26,
RESERVED_SWITCH_5_BIT27,
RESERVED_SWITCH_5_BIT28,
RESERVED_SWITCH_5_BIT29,
RESERVED_SWITCH_5_BIT30,
RESERVED_SWITCH_5_BIT31,
RESERVED_SWITCH_5_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_5_BIT1,
RESERVED_SWITCH_5_BIT2,
RESERVED_SWITCH_5_BIT3,
RESERVED_SWITCH_5_BIT4,
RESERVED_SWITCH_5_BIT5,
RESERVED_SWITCH_5_BIT6,
RESERVED_SWITCH_5_BIT7,
RESERVED_SWITCH_5_BIT8,
RESERVED_SWITCH_5_BIT9,
RESERVED_SWITCH_5_BIT10,
RESERVED_SWITCH_5_BIT11,
RESERVED_SWITCH_5_BIT12,
RESERVED_SWITCH_5_BIT13,
RESERVED_SWITCH_5_BIT14,
RESERVED_SWITCH_5_BIT15,
RESERVED_SWITCH_5_BIT16,
RESERVED_SWITCH_5_BIT17,
RESERVED_SWITCH_5_BIT18,
RESERVED_SWITCH_5_BIT19,
RESERVED_SWITCH_5_BIT20,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_5_BIT21,
RESERVED_SWITCH_5_BIT22,
RESERVED_SWITCH_5_BIT23,
RESERVED_SWITCH_5_BIT24,
RESERVED_SWITCH_5_BIT25,
RESERVED_SWITCH_5_BIT26,
RESERVED_SWITCH_5_BIT27,
RESERVED_SWITCH_5_BIT28,
RESERVED_SWITCH_5_BIT29,
RESERVED_SWITCH_5_BIT30,
RESERVED_SWITCH_5_BIT31,
RESERVED_SWITCH_5_BIT32
Default Value:
RESERVED_SWITCH_5_BIT1:1,RESERVED_SWITCH_5_BI
T2:1,RESERVED_SWITCH_5_BIT3:1,RESERVED_SWITCH_
5_BIT4:1,RESERVED_SWITCH_5_BIT5:1,RESERVED_SWI
TCH_5_BIT6:1,RESERVED_SWITCH_5_BIT7:1,RESERVED
_SWITCH_5_BIT8:1,RESERVED_SWITCH_5_BIT9:1,RESER
VED_SWITCH_5_BIT10:1,RESERVED_SWITCH_5_BIT11:1,
RESERVED_SWITCH_5_BIT12:1,RESERVED_SWITCH_5_B
IT13:1,RESERVED_SWITCH_5_BIT14:1,RESERVED_SWIT
CH_5_BIT15:1,RESERVED_SWITCH_5_BIT16:1,RESERVED
_SWITCH_5_BIT17:1,RESERVED_SWITCH_5_BIT18:1,RES
ERVED_SWITCH_5_BIT19:1,RESERVED_SWITCH_5_BIT2
0:1,RESERVED_SWITCH_5_BIT21:1,RESERVED_SWITCH_
5_BIT22:1,RESERVED_SWITCH_5_BIT23:1,RESERVED_S
WITCH_5_BIT24:1,RESERVED_SWITCH_5_BIT25:1,RESER
VED_SWITCH_5_BIT26:1,RESERVED_SWITCH_5_BIT27:1,
RESERVED_SWITCH_5_BIT28:1,RESERVED_SWITCH_5_B
IT29:1,RESERVED_SWITCH_5_BIT30:1,RESERVED_SWIT
CH_5_BIT31:1,RESERVED_SWITCH_5_BIT32:1
RsvS B SET No Non
witch5 S UAL ne e
C GOR
6 SVPA
9 RA
1
0

Meaning: RRM algorithm reserved U32 Switch Para 5. The 32bit parameter is reserved for further change request use. Disuse
statement: This parameter is used temporarily in patch versions
and will be replaced with a new parameter in later versions. The
new parameter ID reflects the parameter function. Therefore, this
parameter is not recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_5_BIT1,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_5_BIT2,
RESERVED_SWITCH_5_BIT3,
RESERVED_SWITCH_5_BIT4,
RESERVED_SWITCH_5_BIT5,
RESERVED_SWITCH_5_BIT6,
RESERVED_SWITCH_5_BIT7,
RESERVED_SWITCH_5_BIT8,
RESERVED_SWITCH_5_BIT9,
RESERVED_SWITCH_5_BIT10,
RESERVED_SWITCH_5_BIT11,
RESERVED_SWITCH_5_BIT12,
RESERVED_SWITCH_5_BIT13,
RESERVED_SWITCH_5_BIT14,
RESERVED_SWITCH_5_BIT15,
RESERVED_SWITCH_5_BIT16,
RESERVED_SWITCH_5_BIT17,
RESERVED_SWITCH_5_BIT18,
RESERVED_SWITCH_5_BIT19,
RESERVED_SWITCH_5_BIT20,
RESERVED_SWITCH_5_BIT21,
RESERVED_SWITCH_5_BIT22,
RESERVED_SWITCH_5_BIT23,
RESERVED_SWITCH_5_BIT24,
RESERVED_SWITCH_5_BIT25,
RESERVED_SWITCH_5_BIT26,
RESERVED_SWITCH_5_BIT27,
RESERVED_SWITCH_5_BIT28,
RESERVED_SWITCH_5_BIT29,
RESERVED_SWITCH_5_BIT30,
RESERVED_SWITCH_5_BIT31,
RESERVED_SWITCH_5_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_5_BIT1,
RESERVED_SWITCH_5_BIT2,
RESERVED_SWITCH_5_BIT3,
RESERVED_SWITCH_5_BIT4,
RESERVED_SWITCH_5_BIT5,
RESERVED_SWITCH_5_BIT6,
RESERVED_SWITCH_5_BIT7,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_5_BIT8,
RESERVED_SWITCH_5_BIT9,
RESERVED_SWITCH_5_BIT10,
RESERVED_SWITCH_5_BIT11,
RESERVED_SWITCH_5_BIT12,
RESERVED_SWITCH_5_BIT13,
RESERVED_SWITCH_5_BIT14,
RESERVED_SWITCH_5_BIT15,
RESERVED_SWITCH_5_BIT16,
RESERVED_SWITCH_5_BIT17,
RESERVED_SWITCH_5_BIT18,
RESERVED_SWITCH_5_BIT19,
RESERVED_SWITCH_5_BIT20,
RESERVED_SWITCH_5_BIT21,
RESERVED_SWITCH_5_BIT22,
RESERVED_SWITCH_5_BIT23,
RESERVED_SWITCH_5_BIT24,
RESERVED_SWITCH_5_BIT25,
RESERVED_SWITCH_5_BIT26,
RESERVED_SWITCH_5_BIT27,
RESERVED_SWITCH_5_BIT28,
RESERVED_SWITCH_5_BIT29,
RESERVED_SWITCH_5_BIT30,
RESERVED_SWITCH_5_BIT31,
RESERVED_SWITCH_5_BIT32
Default Value:
RESERVED_SWITCH_5_BIT1:1,RESERVED_SWITCH_5_BI
T2:1,RESERVED_SWITCH_5_BIT3:1,RESERVED_SWITCH_
5_BIT4:1,RESERVED_SWITCH_5_BIT5:1,RESERVED_SWI
TCH_5_BIT6:1,RESERVED_SWITCH_5_BIT7:1,RESERVED
_SWITCH_5_BIT8:1,RESERVED_SWITCH_5_BIT9:1,RESER
VED_SWITCH_5_BIT10:1,RESERVED_SWITCH_5_BIT11:1,
RESERVED_SWITCH_5_BIT12:1,RESERVED_SWITCH_5_B
IT13:1,RESERVED_SWITCH_5_BIT14:1,RESERVED_SWIT
CH_5_BIT15:1,RESERVED_SWITCH_5_BIT16:1,RESERVED
_SWITCH_5_BIT17:1,RESERVED_SWITCH_5_BIT18:1,RES
ERVED_SWITCH_5_BIT19:1,RESERVED_SWITCH_5_BIT2
0:1,RESERVED_SWITCH_5_BIT21:1,RESERVED_SWITCH_
5_BIT22:1,RESERVED_SWITCH_5_BIT23:1,RESERVED_S

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

WITCH_5_BIT24:1,RESERVED_SWITCH_5_BIT25:1,RESER
VED_SWITCH_5_BIT26:1,RESERVED_SWITCH_5_BIT27:1,
RESERVED_SWITCH_5_BIT28:1,RESERVED_SWITCH_5_B
IT29:1,RESERVED_SWITCH_5_BIT30:1,RESERVED_SWIT
CH_5_BIT31:1,RESERVED_SWITCH_5_BIT32:1
RSVS B SET No Non
WITC S UNR ne e
H0
C NCR
6 SVPA
9 RA
0
0

Meaning: Reserved Switch 0. The para reserved for further


change request use. Disuse statement: This parameter is used
temporarily in patch versions and will be replaced with a new
parameter in later versions. The new parameter ID reflects the
parameter function. Therefore, this parameter is not
recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Default Value:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT1:0,RESERVED_SWITCH_0_BI
T2:0,RESERVED_SWITCH_0_BIT3:0,RESERVED_SWITCH_
0_BIT4:0,RESERVED_SWITCH_0_BIT5:0,RESERVED_SWI
TCH_0_BIT6:0,RESERVED_SWITCH_0_BIT7:0,RESERVED
_SWITCH_0_BIT8:0,RESERVED_SWITCH_0_BIT9:0,RESER
VED_SWITCH_0_BIT10:0,RESERVED_SWITCH_0_BIT11:0,
RESERVED_SWITCH_0_BIT12:0,RESERVED_SWITCH_0_B
IT13:0,RESERVED_SWITCH_0_BIT14:0,RESERVED_SWIT
CH_0_BIT15:0,RESERVED_SWITCH_0_BIT16:0,RESERVED
_SWITCH_0_BIT17:0,RESERVED_SWITCH_0_BIT18:0,RES
ERVED_SWITCH_0_BIT19:0,RESERVED_SWITCH_0_BIT2
0:0,RESERVED_SWITCH_0_BIT21:0,RESERVED_SWITCH_
0_BIT22:0,RESERVED_SWITCH_0_BIT23:0,RESERVED_S
WITCH_0_BIT24:0,RESERVED_SWITCH_0_BIT25:0,RESER
VED_SWITCH_0_BIT26:0,RESERVED_SWITCH_0_BIT27:0,
RESERVED_SWITCH_0_BIT28:0,RESERVED_SWITCH_0_B
IT29:0,RESERVED_SWITCH_0_BIT30:0,RESERVED_SWIT
CH_0_BIT31:0,RESERVED_SWITCH_0_BIT32:0
RSVS B SET No Non
WITC S UNR ne e
H0
C NCR
6 SVPA
9 RA
1
0

Meaning: Reserved Switch 0. The para reserved for further


change request use. Disuse statement: This parameter is used
temporarily in patch versions and will be replaced with a new
parameter in later versions. The new parameter ID reflects the
parameter function. Therefore, this parameter is not
recommended for the configuration interface.
GUI Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,
RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Unit: None
Actual Value Range: RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT2,
RESERVED_SWITCH_0_BIT3,
RESERVED_SWITCH_0_BIT4,
RESERVED_SWITCH_0_BIT5,
RESERVED_SWITCH_0_BIT6,
RESERVED_SWITCH_0_BIT7,
RESERVED_SWITCH_0_BIT8,
RESERVED_SWITCH_0_BIT9,
RESERVED_SWITCH_0_BIT10,
RESERVED_SWITCH_0_BIT11,
RESERVED_SWITCH_0_BIT12,
RESERVED_SWITCH_0_BIT13,
RESERVED_SWITCH_0_BIT14,
RESERVED_SWITCH_0_BIT15,
RESERVED_SWITCH_0_BIT16,
RESERVED_SWITCH_0_BIT17,
RESERVED_SWITCH_0_BIT18,
RESERVED_SWITCH_0_BIT19,
RESERVED_SWITCH_0_BIT20,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

RESERVED_SWITCH_0_BIT21,
RESERVED_SWITCH_0_BIT22,
RESERVED_SWITCH_0_BIT23,
RESERVED_SWITCH_0_BIT24,
RESERVED_SWITCH_0_BIT25,
RESERVED_SWITCH_0_BIT26,
RESERVED_SWITCH_0_BIT27,
RESERVED_SWITCH_0_BIT28,
RESERVED_SWITCH_0_BIT29,
RESERVED_SWITCH_0_BIT30,
RESERVED_SWITCH_0_BIT31,
RESERVED_SWITCH_0_BIT32
Default Value:
RESERVED_SWITCH_0_BIT1:0,RESERVED_SWITCH_0_BI
T2:0,RESERVED_SWITCH_0_BIT3:0,RESERVED_SWITCH_
0_BIT4:0,RESERVED_SWITCH_0_BIT5:0,RESERVED_SWI
TCH_0_BIT6:0,RESERVED_SWITCH_0_BIT7:0,RESERVED
_SWITCH_0_BIT8:0,RESERVED_SWITCH_0_BIT9:0,RESER
VED_SWITCH_0_BIT10:0,RESERVED_SWITCH_0_BIT11:0,
RESERVED_SWITCH_0_BIT12:0,RESERVED_SWITCH_0_B
IT13:0,RESERVED_SWITCH_0_BIT14:0,RESERVED_SWIT
CH_0_BIT15:0,RESERVED_SWITCH_0_BIT16:0,RESERVED
_SWITCH_0_BIT17:0,RESERVED_SWITCH_0_BIT18:0,RES
ERVED_SWITCH_0_BIT19:0,RESERVED_SWITCH_0_BIT2
0:0,RESERVED_SWITCH_0_BIT21:0,RESERVED_SWITCH_
0_BIT22:0,RESERVED_SWITCH_0_BIT23:0,RESERVED_S
WITCH_0_BIT24:0,RESERVED_SWITCH_0_BIT25:0,RESER
VED_SWITCH_0_BIT26:0,RESERVED_SWITCH_0_BIT27:0,
RESERVED_SWITCH_0_BIT28:0,RESERVED_SWITCH_0_B
IT29:0,RESERVED_SWITCH_0_BIT30:0,RESERVED_SWIT
CH_0_BIT31:0,RESERVED_SWITCH_0_BIT32:0
Hsdpa
CMPe
rmissi
onInd

B SET
S UCM
C CF
6
9
0
0

W
RF
D01
06
12
04

HS
UP
A
Mo
bilit
y
Ma

Meaning: Whether the compressed mode (CM) can be activated


when an HSDPA service is in progress and whether an HSDPA
service can be set up when the CM is active. If this parameter is
set to TRUE: 1. the RNC can enable the CM for HSDPA
services. 2. The HSDPA services can be enabled when the CM is
enabled. If this parameter is set to FALSE: 1. the CM for HSDPA
services can be enabled only after the H2D (HS-DSCH to DCH)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Hsdpa
CMPe
rmissi
onInd

B SET
S UCM
C CF
6
9
1
0

Description

W
RF
D02
03
06

nag
eme
nt
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

channel switch. 2. The HSDPA services cannot be enabled when


the CM is enabled. This switch is used for the compatibility of
the HSDPA terminals that do not support CM when HSDPA is
enabled.
GUI Value Range: FALSE(Forbidden), TRUE(Permit)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: TRUE(Permit)

W
RF
D01
06
12
04
W
RF
D02
03
06

HS
UP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Meaning: Whether the compressed mode (CM) can be activated


when an HSDPA service is in progress and whether an HSDPA
service can be set up when the CM is active. If this parameter is
set to TRUE: 1. the RNC can enable the CM for HSDPA
services. 2. The HSDPA services can be enabled when the CM is
enabled. If this parameter is set to FALSE: 1. the CM for HSDPA
services can be enabled only after the H2D (HS-DSCH to DCH)
channel switch. 2. The HSDPA services cannot be enabled when
the CM is enabled. This switch is used for the compatibility of
the HSDPA terminals that do not support CM when HSDPA is
enabled.
GUI Value Range: FALSE(Forbidden), TRUE(Permit)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: TRUE(Permit)

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Hsupa
CMPe
rmissi
onInd

B SET
S UCM
C CF
6
9
0
0

W
RF
D01
06
10
06
W
RF
D02
03
06

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
rRA
T
Han
dov
er
Bas
ed
on
Loa
d

Meaning: Whether the compressed mode (CM) can be activated


when an HSUPA service is in progress and whether an HSUPA
service can be set up when the CM is active. If this parameter is
set to Permit: 1. the RNC can enable the CM for HSUPA
services. 2. The HSUPA services can be enabled when the CM is
enabled. If this parameter is set to Limited: 1. the CM for
HSUPA services can be enabled only after the E2D (E-DCH to
DCH) channel switch. 2. The HSUPA services cannot be enabled
when the CM is enabled. If this parameter is set to
BasedonUECap, the RNC determines whether CM can be
enabled for HSUPA services and whether HSUPA services can
be enabled when the CM is enabled by considering the UE
capability. This switch is used for the compatibility of the
HSUPA terminals that do not support CM when HSUPA is
enabled.
GUI Value Range: Limited(Limited), Permit(Permit),
BasedOnUECap(Based On UE Capability)
Unit: None
Actual Value Range: Limited, Permit, BasedOnUECap
Default Value: BasedOnUECap(Based On UE Capability)

Hsupa
CMPe
rmissi
onInd

B SET
S UCM
C CF
6
9
1
0

W
RF
D01
06
10
06
W
RF
D02
03
06

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Inte
rRA
T
Han
dov

Meaning: Whether the compressed mode (CM) can be activated


when an HSUPA service is in progress and whether an HSUPA
service can be set up when the CM is active. If this parameter is
set to Permit: 1. the RNC can enable the CM for HSUPA
services. 2. The HSUPA services can be enabled when the CM is
enabled. If this parameter is set to Limited: 1. the CM for
HSUPA services can be enabled only after the E2D (E-DCH to
DCH) channel switch. 2. The HSUPA services cannot be enabled
when the CM is enabled. If this parameter is set to
BasedonUECap, the RNC determines whether CM can be
enabled for HSUPA services and whether HSUPA services can
be enabled when the CM is enabled by considering the UE
capability. This switch is used for the compatibility of the
HSUPA terminals that do not support CM when HSUPA is
enabled.
GUI Value Range: Limited(Limited), Permit(Permit),

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

EHSP
ACM
Permi
ssionI
nd

B SET
S UCM
C CF
6
9
0
0

W
RF
D02
03
02
W
RF
D02
03
03

Description

er
Bas
ed
on
Loa
d

BasedOnUECap(Based On UE Capability)
Unit: None
Actual Value Range: Limited, Permit, BasedOnUECap
Default Value: BasedOnUECap(Based On UE Capability)

Inte
r
Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

Meaning: Whether the compressed mode (CM) can be activated


when an HSPA+ service is in progress and whether an HSPA+
service can be set up when the CM is active. If this parameter is
set to TRUE: 1. the RNC can enable the CM for HSPA+
services. 2. The HSPA+ services can be enabled when the CM is
enabled. If this parameter is set to FALSE: 1. the CM for HSPA+
services can be enabled only after the uplink E2D (E-DCH to
DCH) and downlink H2D (HS-DSCH to DCH) channel switch.
2. The HSPA+ services cannot be enabled when the CM is
enabled. This switch is used for the compatibility of the HSPA+
terminals that do not support CM when HSPA+ is enabled.
GUI Value Range: FALSE(Forbidden), TRUE(Permit)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: FALSE(Forbidden)

EHSP B SET W Inte Meaning: Whether the compressed mode (CM) can be activated
ACM S UCM RF r
when an HSPA+ service is in progress and whether an HSPA+

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
Permi C CF
ssionI 6
nd
9
1
0

McHs
dpaLt
eCMP
ermiss
ionInd

Fre
que
ncy
Har
d
Han
dov
er
Bas
ed
on
Cov
erag
e
Inte
rRA
T
Han
dov
er
Bas
ed
on
Cov
erag
e

service can be set up when the CM is active. If this parameter is


set to TRUE: 1. the RNC can enable the CM for HSPA+
services. 2. The HSPA+ services can be enabled when the CM is
enabled. If this parameter is set to FALSE: 1. the CM for HSPA+
services can be enabled only after the uplink E2D (E-DCH to
DCH) and downlink H2D (HS-DSCH to DCH) channel switch.
2. The HSPA+ services cannot be enabled when the CM is
enabled. This switch is used for the compatibility of the HSPA+
terminals that do not support CM when HSPA+ is enabled.
GUI Value Range: FALSE(Forbidden), TRUE(Permit)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: FALSE(Forbidden)

B SET No Non
S UCM ne e
C CF
6
9
0
0

Meaning: Whether the RNC reconfigures MC-HSDPA services


as HSDPA services for UEs during the LTE cell measurement in
CM. If this parameter is set to FALSE, The RNC reconfigures
MC-HSDPA services as HSDPA services. If this parameter is set
to TRUE, The original algorithm applies.
GUI Value Range: FALSE(Forbidden), TRUE(Permit)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: TRUE(Permit)

McHs B SET

D02
03
02
W
RF
D02
03
03

Description

No Non Meaning: Whether the RNC reconfigures MC-HSDPA services

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
dpaLt
eCMP
ermiss
ionInd

S UCM ne e
C CF
6
9
1
0

PsSwi B SET
tch
S UCO
C RRM
6 ALG
9 OSWI
0 TCH
0

W
RF
D02
11
01
W
RF
D01
06
90
W
RF
D03
00
04

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
TTI
Swi
tch
for
BE
Ser
vice
s
Bas
ed
on
Cov
erag
e
Ada
ptiv

Description

as HSDPA services for UEs during the LTE cell measurement in


CM. If this parameter is set to FALSE, The RNC reconfigures
MC-HSDPA services as HSDPA services. If this parameter is set
to TRUE, The original algorithm applies.
GUI Value Range: FALSE(Forbidden), TRUE(Permit)
Unit: None
Actual Value Range: FALSE, TRUE
Default Value: TRUE(Permit)
Meaning: PS rate negotiation switch group. 1.
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH: When the
switch is on, access at a rate of 0 kbit/s or on the FACH is
determined according to the current connection state of the RRC
if the PS BE admission and the later preemption and queuing
fail. 2. PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH: When
the switch is on, the initial rate of the service should be
dynamically configured according to the value of Ec/No reported
by the UE when the PS BE service is established. 3.
PS_BE_IU_QOS_NEG_SWITCH: When the switch is on, the Iu
QoS Negotiation function is applied to the PS BE service if
Alternative RAB Parameter Values IE is present in the RANAP
RAB ASSIGNMENT REQUEST or RELOCATION REQUEST
message. 4. PS_RAB_DOWNSIZING_SWITCH: When the
switch is on and the RAB downsizing license is activated, the
initial speed is determined on the basis of cell resources.
Downsizing is implemented for BE services. 5.
PS_STREAM_IU_QOS_NEG_SWITCH: When the switch is
on, the Iu QoS Negotiation function is applied to the PS
STREAM service if Alternative RAB Parameter Values IE is
present in the RANAP RAB ASSIGNMENT REQUEST or
RELOCATION REQUEST message. 6.
PS_BE_STRICT_IU_QOS_NEG_SWITCH: When the switch is
on, the strict Iu QoS Negotiation function is applied to the PS BE
service,RNC select Iu max bit rate based on UE capacity,cell
capacity,max bitrate and alternative RAB parameter values in
RANAP RAB ASSIGNMENT REQUEST or RELOCATION
REQUEST message. When the switch is not on, the loose Iu
QoS Negotiation function is applied to the PS BE service,RNC
select Iu max bit rate based on UE capacity,max bitrate and

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
e
Con
figu
rati
on
of
Typ
ical
HS
PA
Rat
e

Description

alternative RAB parameter values in RANAP RAB


ASSIGNMENT REQUEST or RELOCATION REQUEST
message,not consider cell capacity,this can avoid Iu QoS
Renegotiation between different cell.The switch is valid when
PS_BE_IU_QOS_NEG_SWITCH is set to ON. 7.
HSPA_ADPTIVE_RATE_ALGO_SWITCH: When this switch
is turned on, the RNC can calculate the actual maximum traffic
rate of PS BE services over HSPA channels based on the MBR
assigned by the CN, if the license controlling the Adaptive
Configuration of Typical HSPA Rate feature is activated. 8.
PS_CM_COV_H2D_0K_SWITCH: Whether to allocate a 0
kbit/s DCH in the uplink and downlink to HSPA services after
the corresponding UE enters the compressed mode due to poor
coverage.When this switch is turned on, a 0 kbit/s DCH is
allocated to HSPA services in the uplink and downlink after the
corresponding UE enters the compressed mode due to poor
coverage. 9. PS_CMACTIVE_PROCESS_OPT_SWITCH:
Whether to refuse to allocate a high data rate to the PS services
of a UE in compressed mode when the UE applies for a high
data rate by moving to an inter-frequency co-coverage cell using
the directed retry procedure.When this switch is turned on, the
RNC refuses to increase the data rate of the PS services of a UE
in compressed mode when the UE applies for a high data rate by
moving to an inter-frequency co-coverage cell using the directed
retry procedure. 10. PS_CMTIMEOUT_UP_LIMIT_SWITCH:
Whether to refuse to increase the PS data rate of a UE that is in
the weak coverage state. Conventionally, a UE enters the weak
coverage state after reporting the event 2D and exits the state
after reporting the event 2F. During the interval between the two
events, the UE is regarded as being in the weak coverage state.
Note that the UE can also exit the state through other processes,
such as a hard handover. When this switch is turned on, the RNC
refuses to increase the PS data rate of such a UE. 11.
PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH: Whether
the Iu QoS negotiation enhancement function of PS streaming
services takes effect. When this switch is turned on, the Iu QoS
negotiation Enhancement function of PS streaming services
takes effect. The Iu QoS negotiation enhancement function of PS
streaming services includes the following: 1)The Iu QoS

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

negotiation on alternative guarantee bit rates of PS streaming


services is now supported. 2)The Iu QoS negotiation function of
PS services is supported in the inter-RAT handover process.
When this switch is turned off, the Iu QoS negotiation
Enhancement function of PS streaming services does not take
effect. 12. PS_STREAM_IU_QOS_RENEG_SWITCH: Whether
Iu QoS re-negotiation is performed for PS streaming services.
When this switch is turned on, Iu QoS re-negotiation is
performed for streaming services. That is, if the rate over the Uu
interface changes after the RAB establishment, the RNC sends
the RAB MOBIFY REQUEST message to instruct the CN to
modify the maximum bit rate and guarantee bit rate. When this
switch is turned off, Iu QoS re-negotiation is not performed for
streaming services.
GUI Value Range:
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,
PS_BE_IU_QOS_NEG_SWITCH,
PS_RAB_DOWNSIZING_SWITCH,
PS_STREAM_IU_QOS_NEG_SWITCH,
PS_BE_STRICT_IU_QOS_NEG_SWITCH,
HSPA_ADPTIVE_RATE_ALGO_SWITCH,
PS_CM_COV_H2D_0K_SWITCH,
PS_CMACTIVE_PROCESS_OPT_SWITCH,
PS_CMTIMEOUT_UP_LIMIT_SWITCH,
PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH,
PS_STREAM_IU_QOS_RENEG_SWITCH
Unit: None
Actual Value Range:
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,
PS_BE_IU_QOS_NEG_SWITCH,
PS_RAB_DOWNSIZING_SWITCH,
PS_STREAM_IU_QOS_NEG_SWITCH,
PS_BE_STRICT_IU_QOS_NEG_SWITCH,
HSPA_ADPTIVE_RATE_ALGO_SWITCH,
PS_CM_COV_H2D_0K_SWITCH,
PS_CMACTIVE_PROCESS_OPT_SWITCH,
PS_CMTIMEOUT_UP_LIMIT_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH,
PS_STREAM_IU_QOS_RENEG_SWITCH
Default Value:
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH:0,PS_BE_I
NIT_RATE_DYNAMIC_CFG_SWITCH:0,PS_BE_IU_QOS_N
EG_SWITCH:0,PS_RAB_DOWNSIZING_SWITCH:1,PS_STR
EAM_IU_QOS_NEG_SWITCH:0,PS_BE_STRICT_IU_QOS_
NEG_SWITCH:0,HSPA_ADPTIVE_RATE_ALGO_SWITCH:0
,PS_CM_COV_H2D_0K_SWITCH:0,PS_CMACTIVE_PROCE
SS_OPT_SWITCH:0,PS_CMTIMEOUT_UP_LIMIT_SWITCH
:0,PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH:0,
PS_STREAM_IU_QOS_RENEG_SWITCH:1
PsSwi B SET
tch
S UCO
C RRM
6 ALG
9 OSWI
1 TCH
0

W
RF
D02
11
01
W
RF
D01
06
90
W
RF
D03
00
04

Dyn
ami
c
Cha
nnel
Con
figu
rati
on
Con
trol
(DC
CC)
TTI
Swi
tch
for
BE
Ser
vice
s
Bas
ed
on
Cov
erag

Meaning: PS rate negotiation switch group. 1.


PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH: When the
switch is on, access at a rate of 0 kbit/s or on the FACH is
determined according to the current connection state of the RRC
if the PS BE admission and the later preemption and queuing
fail. 2. PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH: When
the switch is on, the initial rate of the service should be
dynamically configured according to the value of Ec/No reported
by the UE when the PS BE service is established. 3.
PS_BE_IU_QOS_NEG_SWITCH: When the switch is on, the Iu
QoS Negotiation function is applied to the PS BE service if
Alternative RAB Parameter Values IE is present in the RANAP
RAB ASSIGNMENT REQUEST or RELOCATION REQUEST
message. 4. PS_RAB_DOWNSIZING_SWITCH: When the
switch is on and the RAB downsizing license is activated, the
initial speed is determined on the basis of cell resources.
Downsizing is implemented for BE services. 5.
PS_STREAM_IU_QOS_NEG_SWITCH: When the switch is
on, the Iu QoS Negotiation function is applied to the PS
STREAM service if Alternative RAB Parameter Values IE is
present in the RANAP RAB ASSIGNMENT REQUEST or
RELOCATION REQUEST message. 6.
PS_BE_STRICT_IU_QOS_NEG_SWITCH: When the switch is
on, the strict Iu QoS Negotiation function is applied to the PS BE
service,RNC select Iu max bit rate based on UE capacity,cell
capacity,max bitrate and alternative RAB parameter values in

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
e
Ada
ptiv
e
Con
figu
rati
on
of
Typ
ical
HS
PA
Rat
e

Description

RANAP RAB ASSIGNMENT REQUEST or RELOCATION


REQUEST message. When the switch is not on, the loose Iu
QoS Negotiation function is applied to the PS BE service,RNC
select Iu max bit rate based on UE capacity,max bitrate and
alternative RAB parameter values in RANAP RAB
ASSIGNMENT REQUEST or RELOCATION REQUEST
message,not consider cell capacity,this can avoid Iu QoS
Renegotiation between different cell.The switch is valid when
PS_BE_IU_QOS_NEG_SWITCH is set to ON. 7.
HSPA_ADPTIVE_RATE_ALGO_SWITCH: When this switch
is turned on, the RNC can calculate the actual maximum traffic
rate of PS BE services over HSPA channels based on the MBR
assigned by the CN, if the license controlling the Adaptive
Configuration of Typical HSPA Rate feature is activated. 8.
PS_CM_COV_H2D_0K_SWITCH: Whether to allocate a 0
kbit/s DCH in the uplink and downlink to HSPA services after
the corresponding UE enters the compressed mode due to poor
coverage.When this switch is turned on, a 0 kbit/s DCH is
allocated to HSPA services in the uplink and downlink after the
corresponding UE enters the compressed mode due to poor
coverage. 9. PS_CMACTIVE_PROCESS_OPT_SWITCH:
Whether to refuse to allocate a high data rate to the PS services
of a UE in compressed mode when the UE applies for a high
data rate by moving to an inter-frequency co-coverage cell using
the directed retry procedure.When this switch is turned on, the
RNC refuses to increase the data rate of the PS services of a UE
in compressed mode when the UE applies for a high data rate by
moving to an inter-frequency co-coverage cell using the directed
retry procedure. 10. PS_CMTIMEOUT_UP_LIMIT_SWITCH:
Whether to refuse to increase the PS data rate of a UE that is in
the weak coverage state. Conventionally, a UE enters the weak
coverage state after reporting the event 2D and exits the state
after reporting the event 2F. During the interval between the two
events, the UE is regarded as being in the weak coverage state.
Note that the UE can also exit the state through other processes,
such as a hard handover. When this switch is turned on, the RNC
refuses to increase the PS data rate of such a UE. 11.
PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH: Whether
the Iu QoS negotiation enhancement function of PS streaming

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

services takes effect. When this switch is turned on, the Iu QoS
negotiation Enhancement function of PS streaming services
takes effect. The Iu QoS negotiation enhancement function of PS
streaming services includes the following: 1)The Iu QoS
negotiation on alternative guarantee bit rates of PS streaming
services is now supported. 2)The Iu QoS negotiation function of
PS services is supported in the inter-RAT handover process.
When this switch is turned off, the Iu QoS negotiation
Enhancement function of PS streaming services does not take
effect. 12. PS_STREAM_IU_QOS_RENEG_SWITCH: Whether
Iu QoS re-negotiation is performed for PS streaming services.
When this switch is turned on, Iu QoS re-negotiation is
performed for streaming services. That is, if the rate over the Uu
interface changes after the RAB establishment, the RNC sends
the RAB MOBIFY REQUEST message to instruct the CN to
modify the maximum bit rate and guarantee bit rate. When this
switch is turned off, Iu QoS re-negotiation is not performed for
streaming services.
GUI Value Range:
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,
PS_BE_IU_QOS_NEG_SWITCH,
PS_RAB_DOWNSIZING_SWITCH,
PS_STREAM_IU_QOS_NEG_SWITCH,
PS_BE_STRICT_IU_QOS_NEG_SWITCH,
HSPA_ADPTIVE_RATE_ALGO_SWITCH,
PS_CM_COV_H2D_0K_SWITCH,
PS_CMACTIVE_PROCESS_OPT_SWITCH,
PS_CMTIMEOUT_UP_LIMIT_SWITCH,
PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH,
PS_STREAM_IU_QOS_RENEG_SWITCH
Unit: None
Actual Value Range:
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,
PS_BE_IU_QOS_NEG_SWITCH,
PS_RAB_DOWNSIZING_SWITCH,
PS_STREAM_IU_QOS_NEG_SWITCH,
PS_BE_STRICT_IU_QOS_NEG_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

HSPA_ADPTIVE_RATE_ALGO_SWITCH,
PS_CM_COV_H2D_0K_SWITCH,
PS_CMACTIVE_PROCESS_OPT_SWITCH,
PS_CMTIMEOUT_UP_LIMIT_SWITCH,
PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH,
PS_STREAM_IU_QOS_RENEG_SWITCH
Default Value:
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH:0,PS_BE_I
NIT_RATE_DYNAMIC_CFG_SWITCH:0,PS_BE_IU_QOS_N
EG_SWITCH:0,PS_RAB_DOWNSIZING_SWITCH:1,PS_STR
EAM_IU_QOS_NEG_SWITCH:0,PS_BE_STRICT_IU_QOS_
NEG_SWITCH:0,HSPA_ADPTIVE_RATE_ALGO_SWITCH:0
,PS_CM_COV_H2D_0K_SWITCH:0,PS_CMACTIVE_PROCE
SS_OPT_SWITCH:0,PS_CMTIMEOUT_UP_LIMIT_SWITCH
:0,PS_STREAM_IU_QOS_NEG_ENHANCE_SWITCH:0,
PS_STREAM_IU_QOS_RENEG_SWITCH:1
FastH
SCCA
ctTim
eDefO
ffVal

B
S
C
6
9
0
0

ADD
UCE
LLRL
ACT
TIME
MOD
UCE
LLRL
ACT
TIME

W
RF
D01
06
10
06

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt

Meaning: Activation time offset delivered to the UE during the


fast HSDPA serving cell change procedure. This parameter is an
advanced parameter. Therefore, modify the setting of this
parameter under the instruction of Huawei technical support.
GUI Value Range: 1~255
Unit: 10ms
Actual Value Range: 10~2550
Default Value: 30

FastH
SCCA
ctTim
eDefO
ffVal

B
S
C
6
9
1
0

ADD
UCE
LLRL
ACT
TIME
MOD
UCE
LLRL
ACT
TIME

W
RF
D01
06
10
06

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt

Meaning: Activation time offset delivered to the UE during the


fast HSDPA serving cell change procedure. This parameter is an
advanced parameter. Therefore, modify the setting of this
parameter under the instruction of Huawei technical support.
GUI Value Range: 1~255
Unit: 10ms
Actual Value Range: 10~2550
Default Value: 30

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
SpecU
serFun
ctionS
witch3

B
S
C
6
9
0
0

ADD
UIME
ITAC
MOD
UIME
ITAC

W
RF
D01
06
10
06
W
RF
D16
01
03

HS
DP
A
Mo
bilit
y
Ma
nag
eme
nt
Ter
min
al
Bla
ck
List

Description

Meaning: 1) P2F_REDIR_DISABLED_SWITCH (P2F


Redirection Inhibition Switch) Whether a specified UE is
forbidden to perform P2F redirection. 1: This switch is turned
on, a specified UE, for example, a UE that has compatibility
issues with P2F redirection, cannot perform P2F redirection. 0:
This switch is turned off, a specified UE can perform P2F
redirection.
2)SPECUSER_SRB_OVER_HSDPA_DISABLED_SWITCH(S
RB Over HSDPA Inhibition Switch) Whether the downlink SRB
of a specified UE is forbidden to be carried on the HSDPA. 1:
This switch is turned on, the downlink SRB of a specified UE is
forbidden to be carried on the HSDPA. 0: This switch is turned
off, the downlink SRB of a specified UE is allowed to be carried
on the HSDPA.
3)SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH(CPC
DTX/DRX Inhibition Switch) Whether a specified UE is
forbidden to use CPC DTX/DRX. 1: This switch is turned on, a
specified UE is forbidden to use CPC DTX/DRX. 0: This switch
is turned off, a specified UE is allowed to use CPC DTX/DRX.
4)SPECUSER_EFACH_DISABLED_SWITCH(EFACH
Inhibition Switch) Whether a specified UE is forbidden to
establish services on the E-FACH. 1: This switch is turned on. A
specified UE is forbidden to establish services on the E-FACH.
0: This switch is turned off. A specified UE is allowed to
establish services on the E-FACH.
5)SPECUSER_ERACH_DISABLED_SWITCH(ERACH
Inhibition Switch) Whether a specified UE is forbidden to
establish services on the E-RACH. 1: This switch is turned on. A
specified UE is forbidden to establish services on the E-RACH.
0: This switch is turned off. A specified UE is allowed to
establish services on the E-RACH.
6)SPECUSER_PCH_FACH2EFACH_DISABLED_SWITCH
None 7)SPECUSER_INHIBIT_D2P_SWITCH(D2P Procedure
Inhibition Switch) None
8)H_SERV_CELL_CHG_MSG_OPT_DISABLED_SWITCH(D
isable H Serving Cell Change MSG Size Reduction) None
9)EFACH_ERACH_UE_D2P_DISABLED_SWITCH(EFACH/E-RACH UE D2P Disable Switch) 1:When this switch is
turned on, specified UEs enabled with the E-FACH or E-RACH

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

feature cannot perform a D2P state transition. 0:When this


switch is turned off, specified UEs enabled with the E-FACH or
E-RACH feature can perform a D2P state transition.
10)SPECUSER_DL_BLER_MEAS_DISABLED_SWITCH(Dis
able Periodic DL Transport Channel BLER Measurement
Switch) Whether the RNC delivers periodic MR measurement
control messages on DL Transport Channel BLER to UEs of
specified TACs. 1: This switch is turned on. The RNC does not
deliver periodic MR measurement control messages on DL
Transport Channel BLER to UEs of specified TACs. 0: This
switch is turned off. The RNC delivers periodic MR
measurement control messages on DL Transport Channel BLER
to UEs of specified TACs.
11)SPECUSER_AGPS_MEAS_DISABLED_SWITCH(Disable
Periodic AGPS Measurement Switch) Whether the RNC delivers
periodic MR measurement control messages on assisted GPS
(AGPS) to UEs of specified TACs. 1: This switch is turned on.
The RNC does not deliver periodic MR measurement control
messages on AGPS to UEs of specified TACs. 0: This switch is
turned off. The RNC delivers periodic MR measurement control
messages on AGPS to UEs of specified TACs.
12)SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH(
Disable Periodic UE Tx Power Measurement Switch) Whether
the RNC delivers periodic MR measurement control messages
on UE Tx Power to UEs of specified TACs. 1: This switch is
turned on. The RNC does not deliver periodic MR measurement
control messages on UE Tx Power to UEs of specified TACs. 0:
This switch is turned off. The RNC delivers periodic MR
measurement control messages on UE Tx Power to UEs of
specified TACs.
13)SPECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH(
Disable Periodic CELLID RTT Measurement Switch) Whether
the RNC delivers periodic MR measurement control messages
on CELLID RTT to UEs of specified TACs. 1: This switch is
turned on. The RNC does not deliver periodic MR measurement
control messages on CELLID RTT to UEs of specified TACs. 0:
This switch is turned off. The RNC delivers periodic MR
measurement control messages on CELLID RTT to UEs of
specified TACs.

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

14)FAST_H_SERV_CELL_CHANGE_DISABLED_SWITCH
(Fast HSDPA Serving Cell Change Optimization Disable Switch)
Whether to disable the fast HSDPA serving cell change
optimization function for a specified UE. 1: When this switch is
turned on, the fast HSDPA serving cell change optimization
function cannot be used for a specified UE. The original HSDPA
serving cell change procedure is used. 0: When this switch is
turned off, the fast HSDPA serving cell change optimization
function can be used for a specified UE.
15)SPECUSER_R6_EFACH_CMP_SWITCH Whether the RNC
performs special processing on special users that comply with
3GPP Release 6 when these users mistakenly switch to the
enhanced CELL_FACH state in an E-FACH cell. 1: When this
switch is set to on, special users are not allowed to switch to the
CELL_PCH or CELL_FACH state. That is, when special users
have data to transmit, they switch to the CELL_DCH state.
Otherwise, they stay in the idle mode. When special users move
from a FACH cell to an E-FACH cell and initiate a cell
reselection or cell update procedure, the RNC releases the
special users' connections after the cell update or cell reselection
procedure is complete if the UE is in the CELL_FACH state
before the cell reselection or cell update procedure. If the UE is
in the CELL_PCH state before the cell reselection or cell update
procedure, the RNC switches the UE to the CELL_DCH state. 0:
When this switch is set to off, the RNC performs no special
processing on the UE.
GUI Value Range: P2F_REDIR_DISABLED_SWITCH,
SPECUSER_SRB_OVER_HSDPA_DISABLED_SWITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH,
SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SWITCH,
SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SWITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWITCH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

FAST_H_SERV_CELL_CHANGE_DISABLED_SWITCH,
SPECUSER_R6_EFACH_CMP_SWITCH
Unit: None
Actual Value Range: P2F_REDIR_DISABLED_SWITCH,
SPECUSER_SRB_OVER_HSDPA_DISABLED_SWITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH,
SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SWITCH,
SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SWITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWITCH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SWITCH,
SPECUSER_R6_EFACH_CMP_SWITCH
Default Value:
P2F_REDIR_DISABLED_SWITCH:0,SPECUSER_SRB_OVE
R_HSDPA_DISABLED_SWITCH:0,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH:0,
SPECUSER_EFACH_DISABLED_SWITCH:0,
SPECUSER_ERACH_DISABLED_SWITCH:0,SPECUSER_P
CH_FACH2EFACH_DISABLED_SWITCH:0,SPECUSER_IN
HIBIT_D2P_SWITCH:0,H_SERV_CELL_CHG_MSG_OPT_D
ISABLED_SWITCH:0,EFACH_ERACH_UE_D2P_DISABLE
D_SWITCH:0,SPECUSER_DL_BLER_MEAS_DISABLED_S
WITCH:0,SPECUSER_AGPS_MEAS_DISABLED_SWITCH:0
,SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH:0,S
PECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH:0,FA
ST_H_SERV_CELL_CHANGE_DISABLED_SWITCH:0,SPE
CUSER_R6_EFACH_CMP_SWITCH:0
SpecU
serFun
ctionS
witch3

B
S
C
6
9

ADD
UIME
ITAC
MOD
UIME

W
RF
D01
06

HS
DP
A
Mo
bilit

Meaning: 1) P2F_REDIR_DISABLED_SWITCH (P2F


Redirection Inhibition Switch) Whether a specified UE is
forbidden to perform P2F redirection. 1: This switch is turned
on, a specified UE, for example, a UE that has compatibility
issues with P2F redirection, cannot perform P2F redirection. 0:

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID
1 ITAC 10
0
06
W
RF
D16
01
03

y
Ma
nag
eme
nt
Ter
min
al
Bla
ck
List

Description

This switch is turned off, a specified UE can perform P2F


redirection.
2)SPECUSER_SRB_OVER_HSDPA_DISABLED_SWITCH(S
RB Over HSDPA Inhibition Switch) Whether the downlink SRB
of a specified UE is forbidden to be carried on the HSDPA. 1:
This switch is turned on, the downlink SRB of a specified UE is
forbidden to be carried on the HSDPA. 0: This switch is turned
off, the downlink SRB of a specified UE is allowed to be carried
on the HSDPA.
3)SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH(CPC
DTX/DRX Inhibition Switch) Whether a specified UE is
forbidden to use CPC DTX/DRX. 1: This switch is turned on, a
specified UE is forbidden to use CPC DTX/DRX. 0: This switch
is turned off, a specified UE is allowed to use CPC DTX/DRX.
4)SPECUSER_EFACH_DISABLED_SWITCH(EFACH
Inhibition Switch) Whether a specified UE is forbidden to
establish services on the E-FACH. 1: This switch is turned on. A
specified UE is forbidden to establish services on the E-FACH.
0: This switch is turned off. A specified UE is allowed to
establish services on the E-FACH.
5)SPECUSER_ERACH_DISABLED_SWITCH(ERACH
Inhibition Switch) Whether a specified UE is forbidden to
establish services on the E-RACH. 1: This switch is turned on. A
specified UE is forbidden to establish services on the E-RACH.
0: This switch is turned off. A specified UE is allowed to
establish services on the E-RACH.
6)SPECUSER_PCH_FACH2EFACH_DISABLED_SWITCH
None 7)SPECUSER_INHIBIT_D2P_SWITCH(D2P Procedure
Inhibition Switch) None
8)H_SERV_CELL_CHG_MSG_OPT_DISABLED_SWITCH(D
isable H Serving Cell Change MSG Size Reduction) None
9)EFACH_ERACH_UE_D2P_DISABLED_SWITCH(EFACH/E-RACH UE D2P Disable Switch) 1:When this switch is
turned on, specified UEs enabled with the E-FACH or E-RACH
feature cannot perform a D2P state transition. 0:When this
switch is turned off, specified UEs enabled with the E-FACH or
E-RACH feature can perform a D2P state transition.
10)SPECUSER_DL_BLER_MEAS_DISABLED_SWITCH(Dis
able Periodic DL Transport Channel BLER Measurement

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Switch) Whether the RNC delivers periodic MR measurement


control messages on DL Transport Channel BLER to UEs of
specified TACs. 1: This switch is turned on. The RNC does not
deliver periodic MR measurement control messages on DL
Transport Channel BLER to UEs of specified TACs. 0: This
switch is turned off. The RNC delivers periodic MR
measurement control messages on DL Transport Channel BLER
to UEs of specified TACs.
11)SPECUSER_AGPS_MEAS_DISABLED_SWITCH(Disable
Periodic AGPS Measurement Switch) Whether the RNC delivers
periodic MR measurement control messages on assisted GPS
(AGPS) to UEs of specified TACs. 1: This switch is turned on.
The RNC does not deliver periodic MR measurement control
messages on AGPS to UEs of specified TACs. 0: This switch is
turned off. The RNC delivers periodic MR measurement control
messages on AGPS to UEs of specified TACs.
12)SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH(
Disable Periodic UE Tx Power Measurement Switch) Whether
the RNC delivers periodic MR measurement control messages
on UE Tx Power to UEs of specified TACs. 1: This switch is
turned on. The RNC does not deliver periodic MR measurement
control messages on UE Tx Power to UEs of specified TACs. 0:
This switch is turned off. The RNC delivers periodic MR
measurement control messages on UE Tx Power to UEs of
specified TACs.
13)SPECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH(
Disable Periodic CELLID RTT Measurement Switch) Whether
the RNC delivers periodic MR measurement control messages
on CELLID RTT to UEs of specified TACs. 1: This switch is
turned on. The RNC does not deliver periodic MR measurement
control messages on CELLID RTT to UEs of specified TACs. 0:
This switch is turned off. The RNC delivers periodic MR
measurement control messages on CELLID RTT to UEs of
specified TACs.
14)FAST_H_SERV_CELL_CHANGE_DISABLED_SWITCH
(Fast HSDPA Serving Cell Change Optimization Disable Switch)
Whether to disable the fast HSDPA serving cell change
optimization function for a specified UE. 1: When this switch is
turned on, the fast HSDPA serving cell change optimization

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

function cannot be used for a specified UE. The original HSDPA


serving cell change procedure is used. 0: When this switch is
turned off, the fast HSDPA serving cell change optimization
function can be used for a specified UE.
15)SPECUSER_R6_EFACH_CMP_SWITCH Whether the RNC
performs special processing on special users that comply with
3GPP Release 6 when these users mistakenly switch to the
enhanced CELL_FACH state in an E-FACH cell. 1: When this
switch is set to on, special users are not allowed to switch to the
CELL_PCH or CELL_FACH state. That is, when special users
have data to transmit, they switch to the CELL_DCH state.
Otherwise, they stay in the idle mode. When special users move
from a FACH cell to an E-FACH cell and initiate a cell
reselection or cell update procedure, the RNC releases the
special users' connections after the cell update or cell reselection
procedure is complete if the UE is in the CELL_FACH state
before the cell reselection or cell update procedure. If the UE is
in the CELL_PCH state before the cell reselection or cell update
procedure, the RNC switches the UE to the CELL_DCH state. 0:
When this switch is set to off, the RNC performs no special
processing on the UE.
GUI Value Range: P2F_REDIR_DISABLED_SWITCH,
SPECUSER_SRB_OVER_HSDPA_DISABLED_SWITCH,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH,
SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SWITCH,
SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SWITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWITCH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SWITCH,
SPECUSER_R6_EFACH_CMP_SWITCH
Unit: None
Actual Value Range: P2F_REDIR_DISABLED_SWITCH,
SPECUSER_SRB_OVER_HSDPA_DISABLED_SWITCH,

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH,
SPECUSER_EFACH_DISABLED_SWITCH,
SPECUSER_ERACH_DISABLED_SWITCH,
SPECUSER_PCH_FACH2EFACH_DISABLED_SWITCH,
SPECUSER_INHIBIT_D2P_SWITCH,
H_SERV_CELL_CHG_MSG_OPT_DISABLED_SWITCH,
EFACH_ERACH_UE_D2P_DISABLED_SWITCH,
SPECUSER_DL_BLER_MEAS_DISABLED_SWITCH,
SPECUSER_AGPS_MEAS_DISABLED_SWITCH,
SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH,
SPECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH,
FAST_H_SERV_CELL_CHANGE_DISABLED_SWITCH,
SPECUSER_R6_EFACH_CMP_SWITCH
Default Value:
P2F_REDIR_DISABLED_SWITCH:0,SPECUSER_SRB_OVE
R_HSDPA_DISABLED_SWITCH:0,
SPECUSER_CPC_DTX_DRX_DISABLED_SWITCH:0,
SPECUSER_EFACH_DISABLED_SWITCH:0,
SPECUSER_ERACH_DISABLED_SWITCH:0,SPECUSER_P
CH_FACH2EFACH_DISABLED_SWITCH:0,SPECUSER_IN
HIBIT_D2P_SWITCH:0,H_SERV_CELL_CHG_MSG_OPT_D
ISABLED_SWITCH:0,EFACH_ERACH_UE_D2P_DISABLE
D_SWITCH:0,SPECUSER_DL_BLER_MEAS_DISABLED_S
WITCH:0,SPECUSER_AGPS_MEAS_DISABLED_SWITCH:0
,SPECUSER_UE_TX_PWR_MEAS_DISABLED_SWITCH:0,S
PECUSER_CELLID_RTT_MEAS_DISABLED_SWITCH:0,FA
ST_H_SERV_CELL_CHANGE_DISABLED_SWITCH:0,SPE
CUSER_R6_EFACH_CMP_SWITCH:0
UlLdr B ADD
TrigT S UCE
hd
C LLLD
6 M
9 MOD
0 UCE
0 LLLD
M

W
RF
D02
01
02
W
RF
D02

Loa
d
Me
asur
eme
nt
Inte
r
Fre
que

Meaning: Threshold for triggering uplink LDR. If the ratio of the


uplink load to the uplink capacity is higher than or equal to this
threshold for a duration longer than that specified by the
"UlLdTrnsHysTime" parameter, uplink LDR (preliminary
congestion state) is triggered and LDR actions are performed to
reduce the cell load. The recommended value difference between
"UlLdrRelThd" and "UlLdrTrigThd" is higher than 10% because
the load fluctuates. Otherwise, a cell frequently enters and leaves
the preliminary congestion state.
GUI Value Range: 0~100

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

01
03
W
RF
D02
01
06

ncy Unit: %
Loa Actual Value Range: 0~100
d
Default Value: 55
Bal
anc
e
Loa
d
Res
huff
ling

UlLdr B ADD
TrigT S UCE
hd
C LLLD
6 M
9 MOD
1 UCE
0 LLLD
M

W
RF
D02
01
02
W
RF
D02
01
03
W
RF
D02
01
06

Loa
d
Me
asur
eme
nt
Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Loa
d
Res
huff
ling

Meaning: Threshold for triggering uplink LDR. If the ratio of the


uplink load to the uplink capacity is higher than or equal to this
threshold for a duration longer than that specified by the
"UlLdTrnsHysTime" parameter, uplink LDR (preliminary
congestion state) is triggered and LDR actions are performed to
reduce the cell load. The recommended value difference between
"UlLdrRelThd" and "UlLdrTrigThd" is higher than 10% because
the load fluctuates. Otherwise, a cell frequently enters and leaves
the preliminary congestion state.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 55

DlLdr B ADD
TrigT S UCE
hd
C LLLD
6 M
9 MOD

W
RF
D02
01

Loa
d
Me
asur
eme

Meaning: Threshold for triggering downlink LDR. If the ratio of


the downlink load to the downlink capacity is higher than or
equal to this threshold for a duration longer than that specified
by the "DlLdTrnsHysTime" parameter, downlink LDR
(preliminary congestion state) is triggered and LDR actions are

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

0 UCE 02 nt
performed to reduce the cell load. The recommended value
0 LLLD W Inte difference between "DlLdrRelThd" and "DlLdrTrigThd" is
M
higher than 10% because the load fluctuates. Otherwise, a cell
RF r
D- Fre frequently enters and leaves the preliminary congestion state.
02 que GUI Value Range: 0~100
01 ncy Unit: %
03 Loa Actual Value Range: 0~100
W d
Default Value: 70
RF Bal
D- anc
02 e
01 Mul
17 tiW Car
RF rier
D- Swi
02 tch
01 off
06 Bas
W ed
RF on
D- Traf
02 fic
01 Loa
22 d
Loa
d
Res
huff
ling
Mul
tiCar
rier
Swi
tch
off
Bas
ed

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

on
Qo
S
DlLdr B ADD
TrigT S UCE
hd
C LLLD
6 M
9 MOD
1 UCE
0 LLLD
M

W
RF
D02
01
02
W
RF
D02
01
03
W
RF
D02
01
17
W
RF
D02
01
06
W
RF
D02
01
22

Loa
d
Me
asur
eme
nt
Inte
r
Fre
que
ncy
Loa
d
Bal
anc
e
Mul
tiCar
rier
Swi
tch
off
Bas
ed
on
Traf
fic
Loa
d
Loa
d
Res
huff
ling

Meaning: Threshold for triggering downlink LDR. If the ratio of


the downlink load to the downlink capacity is higher than or
equal to this threshold for a duration longer than that specified
by the "DlLdTrnsHysTime" parameter, downlink LDR
(preliminary congestion state) is triggered and LDR actions are
performed to reduce the cell load. The recommended value
difference between "DlLdrRelThd" and "DlLdrTrigThd" is
higher than 10% because the load fluctuates. Otherwise, a cell
frequently enters and leaves the preliminary congestion state.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 70

Para N MML Fe Fea


meter E Com at ture
ID
mand ur Na
e me
ID

Description

Mul
tiCar
rier
Swi
tch
off
Bas
ed
on
Qo
S

18 Counters
Table 18-1 Counter description

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67175 VS.HHO.AttInterFreq.RNC
428

Number of
InterFrequency
Hard
Handover
Requests for
RNC

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67175 VS.HHO.SuccInterFreq.RNC
429

Number of
Successful
InterFrequency
Hard
Handovers
for RNC

BSC6 WRF
900
D02030
2
WRF
D02030

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID
4

Feature
Name
Frequency
Hard
Handover
Based on
DL QoS

67175 VS.IRATHO.AttOutCS.RNC
945

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts for
WRF
RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.AttInCS.RNC
008

Number of
BSC6 WRF
CS Incoming 900
DInter-RAT
02030
Handover
3
Attempts for
WRF
RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.AttOutPSUTRAN.RNC
098

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts
WRF
Initiated by
DRNC for
02030
RNC
5
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

DHandover
02030 Based on
6
Load
67176 VS.IRATHO.SuccOutPSUTRAN.RNC
100

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF
Initiated by
DRNC for
02030
RNC
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.SuccOutPSUE.RNC
102

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF
Initiated by
DUE for RNC
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67180 VS.HHO.InterFreqOut.Eval.CM
551

Number of
BSC6 WRF
Decisions for 900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers in
02030
Compressed
4
Mode for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
DL QoS

67180 VS.HHO.AttIn
565

Number of
BSC6 WRF
Incoming
900
DHard
02030
Handover
1
Attempts for
WRF
Cell
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.HHO.SuccIn
566

Number of
BSC6 WRF
Successful
900
DIncoming
02030
Hard
1
Handovers in
WRF
the RNC for
DCell
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.HHO.InterFreqIn.Eval.CM
570

Number of
BSC6 WRF
Decisions for 900
DIncoming
02030
Inter2
Frequency
WRF
Hard
D-

Inter
Frequency
Hard
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description
Handovers in
Compressed
Mode for
Cell

NE

Featu
re ID

Feature
Name

02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.RRC.MrRpt.2D
613

Number of
BSC6 WRF
Event 2D
900
DMeasurement
02030
Reports for
2
Cell
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.RRC.MrRpt.2F
614

Number of
BSC6 WRF
Event 2F
900
DMeasurement
02030
Reports for
2
Cell
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.AttOut.NCell
489

Number of
Hard
Handovers
Attempts
Between
Neighboring
Cells

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

DCoverage
02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS
67183 VS.HHO.SuccOut.NCell
490

Number of
Successful
Hard
Handovers
Between
Neighboring
Cells

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.IRATHO.AttOutCS.GCell
495

Number of
CS InterRAT
Outgoing
Handover
Attempts
Between
Neighboring
Cells

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.IRATHO.SuccOutCS.GCell
496

Number of
Successful
CS InterRAT

BSC6 WRF Inter-RAT


900
DHandover
02030 Based on

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.IRATHO.AttOutPSUTRAN.GCell
497

Number of
BSC6 WRF
PS Inter-RAT 900
DOutgoing
02030
Handover
3
Attempts
WRF
Between
DNeighboring
02030
Cells
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.IRATHO.SuccOutPSUTRAN.GCell
498

Number of
BSC6 WRF
Successful
900
DPS Inter-RAT
02030
Outgoing
3
Handovers
WRF
Between
DNeighboring
02030
Cells
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.HHO.AttInterFreqOut
900

Number of
Outgoing
InterFrequency
Hard

Inter
Frequency
Hard
Handover
Based on

Outgoing
Handovers
Between
Neighboring
Cells

NE

BSC6 WRF
900
D02030
2
WRF

Count
er ID

Counter Name

Counter
Description
Handover
Attempts for
Cell

NE

Featu
re ID

Feature
Name

D02030
4
WRF
D02010
6

Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS
Load
Reshufflin
g

67183 VS.HHO.SuccInterFreqOut
901

Number of
Successful
Outgoing
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4
WRF
D02010
6

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS
Load
Reshufflin
g

67183 VS.HHO.FailInterFreqOut.CfgUnsupp
902

Number of
BSC6 WRF
Failed
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4
(Configuratio
n
Unsupported
)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.PyhChFail
903

Number of
Failed

Inter
Frequency

BSC6 WRF
D-

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02030
2
WRF
D02030
4

Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.ISR
904

Number of
BSC6 WRF
Failed
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4
(Incompatibl
e
Simultaneous
Reconfigurat
ion)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.CellUpdt
906

Number of
BSC6 WRF
Failed
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell (Cell
4
Update
Occurred)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.InvCfg
907

Number of
Failed
Outgoing
Inter-

Inter
Frequency
Hard
Handover

Outgoing
InterFrequency
Hard
Handovers
for Cell
(Physical
Channel
Failure)

NE
900

BSC6 WRF
900
D02030
2

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Frequency
Hard
Handovers
for Cell
(Invalid
Configuratio
n)

WRF
D02030
4

Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.NoReply
908

Number of
Failed
Outgoing
InterFrequency
Hard
Handovers
Due to No
Response
from the UE
for Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.AttInterFreqIn
912

Number of
BSC6 WRF
Incoming
900
DInter02030
Frequency
2
Hard
WRF
Handover
DAttempts for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.SuccInterFreqIn
913

Number of
Successful
Incoming
InterFrequency
Hard
Handovers

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter

BSC6 WRF
900
D02030
2
WRF
D02030

Count
er ID

Counter Name

Counter
Description
for Cell

NE

Featu
re ID
4

Feature
Name
Frequency
Hard
Handover
Based on
DL QoS

67189 VS.HHO.EvalOut
722

Number of
BSC6 WRF
Decisions for 900
DOutgoing
02030
Hard
1
Handovers
WRF
for Cell
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67189 VS.HHO.EvalIn
723

Number of
BSC6 WRF
Decisions for 900
DIncoming
02030
Hard
1
Handovers
WRF
for Cell
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67189 VS.IRATHO.AttRelocPrepOutCS.Load
739

Number of
Preparation

Inter-RAT
Handover

BSC6 WRF
900
D-

Count
er ID

Counter Name

Counter
Description
Attempts for
CS Outgoing
Inter-RAT
Handover
Initiated by
UTRAN
Based on
Load for Cell

NE

Featu
re ID

Feature
Name

02030 Based on
6
Load

67189 VS.IRATHO.SuccRelocPrepOutCS.Load
740

Number of
BSC6 WRF
Successful
900
DPreparations
02030
for CS
6
Outgoing
Inter-RAT
Handover
Initiated by
UTRAN
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.SuccOutCS.Load
741

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Inter-RAT
6
Handovers
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.AttOutPSUTRAN.Load
742

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
6
Attempts
Initiated by
UTRAN
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.SuccOutPSUTRAN.Load
743

Number of
BSC6 WRF Inter-RAT
Successful
900
DHandover
PS Outgoing
02030 Based on

Count
er ID

Counter Name

Counter
Description
Inter-RAT
Handovers
Initiated by
UTRAN
Based on
Load for Cell

NE

Featu
re ID
6

Feature
Name
Load

67189 VS.IRATHO.AttRelocPrepOutCS.RF
744

Number of
BSC6 WRF
Preparation 900
DAttempts for
02030
CS Outgoing
3
Inter-RAT
Handover
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 VS.IRATHO.SuccRelocPrepOutCS.RF
745

Number of
BSC6 WRF
Successful
900
DPreparations
02030
for CS
3
Outgoing
Inter-RAT
Handover
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 VS.IRATHO.SuccOutCS.RF
746

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Inter-RAT
3
Handovers
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67189 VS.IRATHO.AttOutPSUTRAN.RF
747

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts
Initiated by
the RNC
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 VS.IRATHO.SuccOutPSUTRAN.RF
748

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RAT
3
Handovers
Initiated by
the RNC
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 IRATHO.AttRelocPrepOutCS
749

Number of
BSC6 WRF
Preparation 900
DAttempts for
02040
CS Outgoing
002
Inter-RAT
WRF
Handover for
DCell
02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67189 IRATHO.SuccRelocPrepOutCS
750

Number of
BSC6 WRF
Successful
900
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailRelocPrepOutCS.TAlExp
751

Number of
BSC6 WRF
Failed
900
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
(TRELOCall
WRF
oc expiry)
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailRelocPrepOutCS.TgtFail
752

Number of
BSC6 WRF
Failed
900
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailRelocPrepOutCS.ReloNoSu Number of


BSC6 WRF
753
p
Failed
900
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
(Relocation
WRF
not
Dsupported in
02030
Target RNC
5
or Target
WRF
system)
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.AttOutCS
754

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover

Cell
(Relocation
Failure in
Target
CN/RNC or
Target
System)

NE

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02040
Handover
002
Attempts
WRF
D02030
3
WRF
D02030
5
WRF
D-

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Based on
6
Load
67189 IRATHO.SuccOutCS
755

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02040
Inter-RAT
002
Handovers
WRF
for Cell
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailOutCS.CfgUnsupp
756

Number of
BSC6 WRF
Failed CS
900
DOutgoing
02040
Inter-RAT
002
Handovers
WRF
for Cell
D(Configuratio
02030
n
3
Unsupported
WRF
)
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailOutCS.PhyChFail
757

Number of
Failed CS
Outgoing
Inter-RAT

Inter
System
Direct
Retry

BSC6 WRF
900
D02040
002

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.AttRelocPrepInCS
758

Number of
BSC6 WRF
Preparations 900
Dfor CS
02040
Incoming
002
Inter-RAT
WRF
Handover for
DCell
02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.SuccInCS
759

Number of
BSC6 WRF
Successful
900
DCS Incoming
02040
Inter-RAT
002
Handovers
WRF
for Cell
D02030
3
WRF
D02030

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on

Handovers
for Cell
(Physical
Channel
Failure)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

5
WRF
D02030
6

Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.FailRelocPrepInCS.TRNCS Number of


760
ysFailReloc
Failed
Preparations
for CS
Incoming
Inter-RAT
Handover
(Relocation
failure in
target
CN/RNC or
target
system)

BSC6 WRF
900
D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.FailRelocPrepInCS.TRNCS Number of


761
ysRelocUnsupp
Failed
Preparations
for CS
Incoming
Inter-RAT
Handover
(Relocation
not
supported in
target RNC
or target
system)

BSC6 WRF
900
D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.FailRelocPrepInCS.ResUna Number of

BSC6 WRF

Inter

Count
er ID
762

Counter Name
vail

Counter
Description

NE

Failed
900
Preparations
for CS
Incoming
Inter-RAT
Handover
(No resource
available)

Featu
re ID

Feature
Name

D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.SuccOutPSUE
763

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RAT
802
Handovers
Initiated by
UE for Cell

PS
Handover
Between
UMTS and
GPRS

67189 VS.IRATHO.FailOutCS.UEFail.GCell
907

Number of
BSC6 WRF
Failed CS
900
DInter-RAT
02030
HandoversBe
3
tween
WRF
Neighboring
DCells Due to
02030
UE Fault
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.FaiOutPSUTRAN.UEFail.G Number of


908
Cell
Failed PS
Inter-RAT
Handovers
Between

BSC6 WRF
900
D02030
3

Inter-RAT
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Neighboring
Cells Due to
UE Fault

WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.HHO.FailOut.NoReply.NCell
912

Number of
Failed Hard
Handover
Between
Neighboring
Cells Due to
Timeout

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.IRATHO.AttRelocPrepInCS.RNC
311

Number of
BSC6 WRF
CS Incoming 900
DInter-RAT
02030
Handover
3
Preparation
WRF
Attempts for
DRNC
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccRelocPrepInCS.RNC
312

Number of
Successful
Preparations

BSC6 WRF Inter-RAT


900
DHandover
02030 Based on

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccInCS.RNC
314

Number of
BSC6 WRF
Successful
900
DCS Incoming
02030
Inter-RAT
3
Handovers
WRF
for RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.AttOutPSUE.RNC
316

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts
WRF
Initiated by
DUE for RNC
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.AttRelocPrepOutCS.RNC
398

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02030
Handover
3
Preparation
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT

for CS
Incoming
Inter-RAT
Handover for
RNC

NE

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

D02030
5
WRF
D02030
6

Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccOutCS.RNC
399

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Inter-RAT
3
Handovers
WRF
for RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccRelocPrepOutCS.RNC
400

Number of
BSC6 WRF
Successful
900
DPreparations
02030
for CS
3
Outgoing
WRF
Inter-RAT
DHandover for
02030
RNC
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.FailInCS.NoReply
410

Number of
Failed CS
Inter-RAT
Incoming
Handovers
Due to No
Response
from UE for

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on

Attempts for
RNC

NE

BSC6 WRF
900
D02040
002
WRF
D02030

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 IRATHO.AttOutPSUTRAN
411

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts
WRF
Initiated by
DRNC for Cell
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 IRATHO.SuccOutPSUTRAN
412

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF
Initiated by
DRNC for Cell
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.AttOutPSUE
413

Number of
BSC6 WRF
PS Inter-RAT 900
DOutgoing
02030
Inter-RAT
802
Handover

PS
Handover
Between
UMTS and
GPRS

Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Requests
Initiated by
UE for Cell
67190 VS.IRATHO.SuccRelocPrepInCS
414

Number of
Successful
preparations
for CS
Incoming
Inter-RAT
Handovers
for Cell

BSC6 WRF
900
D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.LCC.LDR.InterRATCS
440

Number of
BSC6 WRF
UEs
900
DPerforming
02030
CS Inter6
RAT
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67190 VS.LCC.LDR.InterRATPS
441

Number of
BSC6 WRF
UEs
900
DPerforming
02030
PS Inter-RAT
6
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67190 IRATHO.FailOutPSUTRAN.CfgUnsupp
476

Number of
Failed PS

Inter-RAT
Handover

BSC6 WRF
900
D-

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02030
3
WRF
D02030
5
WRF
D02030
6

Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.AttRelocPrepOutCS.Service Number of


BSC6 WRF
593
Preparation 900
DAttempts for
02030
CS Outgoing
5
Inter-RAT
Handover
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.HSDPA.SHO.ServCellChg.AttOut
698

HSDPA
Mobility
Manageme
nt

Outgoing
Inter-RAT
Handovers
Initiated by
RNC
(Configuratio
n
unsupported)

67190 IRATHO.FailOutPSUTRAN.PhyChFail
477

Number of
Failed PS
Outgoing
Inter-RAT
Handovers
Initiated by
RNC
(Physical
Channel
Failure)

NE

Number of
BSC6 WRF
Intra-RNC
900
DHSDPA
01061
Serving Cell
006
Change
Attempts for
Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67190 VS.HSDPA.SHO.ServCellChg.SuccOut
699

Number of
BSC6 WRF
Intra-RNC
900
DHSDPA
01061
Serving Cell
006
Change
Success in
RNC for Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.H2H.AttOutIntraFreq
700

Number of
BSC6 WRF
Intra900
DFrequency
01061
HSDPA Hard
006
Handover
Attempts
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.H2H.SuccOutIntraFreq Number of


BSC6 WRF
701
Successful
900
DIntra01061
Frequency
006
HSDPA Hard
Handovers
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.H2H.AttOutInterFreq
702

HSDPA
Mobility
Manageme
nt

Number of
BSC6 WRF
Inter900
DFrequency
01061
HSDPA Hard
006
Handover
Attempts
Without
Channel
Change for
Cell

67190 VS.HSDPA.HHO.H2H.SuccOutInterFreq Number of

BSC6 WRF

HSDPA

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

703

Successful
900
InterFrequency
HSDPA Hard
Handovers
Without
Channel
Change for
Cell

DMobility
01061 Manageme
006
nt

67190 VS.HSDPA.HHO.NoChR.Att.NCell
708

Number of
BSC6 WRF
HSDSCH-to- 900
DHSDSCH
01061
hard
006
Handover
Requests
Without
Channel
Change
Between
Neighboring
Cells

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.NoChR.Succ.NCell
709

Number of
BSC6 WRF
Successful
900
DHSDSCH-to01061
HSDSCH
006
hard
Handovers
Without
Channel
Change
Between
Neighboring
Cells

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.ServCellChg.Att.NCell
710

Number of
HSDPA
Serving Cell
Change
Attempts
Between

HSDPA
Mobility
Manageme
nt

BSC6 WRF
900
D01061
006

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Neighboring
Cells
67190 VS.HSDPA.ServCellChg.Succ.NCell
711

Number of
Successful
HSDPA
Serving Cell
Changes
Between
Neighboring
Cells

BSC6 WRF
900
D01061
006

HSDPA
Mobility
Manageme
nt

67190 VS.IRATHO.SuccRelocPrepOutCS.Servi Number of


BSC6 WRF
856
ce
Successful
900
DPreparations
02030
for CS
5
Outgoing
Inter-RAT
Handover
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.IRATHO.SuccOutCS.Service
857

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Inter-RAT
5
Handovers
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.IRATHO.AttOutPSUTRAN.Service
858

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
5
Attempts
Initiated by
the RNC
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

67190 VS.IRATHO.SuccOutPSUTRAN.Service Number of


BSC6 WRF
859
Successful
900
DPS Outgoing
02030
Inter-RAT
5
Handovers
Initiated by
the RNC
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.HHO.AttInterFreqOut.IntraNodeB
877

Number of
Outgoing
InterFrequency
Hard
Handover
Attempts in
NodeB for
Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.SuccInterFreqOut.IntraNodeB
878

Number of
BSC6 WRF
Successful
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers in
02030
NodeB for
4
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.AttInterFreqOut.InterNodeBIntr Number of


884
aRNC
Outgoing
InterFrequency
Hard

NE

BSC6 WRF
900
D02030
2
WRF

Inter
Frequency
Hard
Handover
Based on

Count
er ID

Counter Name

Counter
Description
Handovers
Attempts
Between
Different
NodeBs of
RNC for Cell

NE

Featu
re ID

Feature
Name

DCoverage
02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.SuccInterFreqOut.InterNodeBIn Number of


BSC6 WRF
885
traRNC
Successful
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between
4
Different
NodeBs of
RNC for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.AttInterFreqOut.InterRNC
891

Number of
Outgoing
InterFrequency
Hard
Handovers
Attempts
Between
RNCs for
Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.SuccInterFreqOut.InterRNC
892

Number of
Successful
Outgoing
InterFrequency
Hard
Handovers
Between

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

RNCs for
Cell

Hard
Handover
Based on
DL QoS

67191 VS.LCC.LDR.HSDPA.InterRATPS
152

Number of
BSC6 WRF
HSDPA UEs 900
DPerforming
02030
PS Inter-RAT
6
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67191 VS.IRATHO.HSDPA.AttOutPSUTRAN
155

Number of
BSC6 WRF
PS Inter-RAT 900
DOutgoing
01061
Handover
006
Attempts for
HSDPA
Services for
Cell

HSDPA
Mobility
Manageme
nt

67191 VS.IRATHO.HSDPA.SuccOutPSUTRAN Number of


BSC6 WRF
156
Successful
900
DPS Outgoing
01061
Inter-RAT
006
Handovers
for HSDPA
Services for
Cell

HSDPA
Mobility
Manageme
nt

67191 VS.HSDPA.HHO.H2D.AttOutIntraFreq
157

HSDPA
Mobility
Manageme
nt

Number of
BSC6 WRF
Intra900
DFrequency
01061
H2D Hard
006
Handover
Attempts for
Cell

67191 VS.HSDPA.HHO.H2D.SuccOutIntraFreq Number of


158
Successful

BSC6 WRF
900
D-

HSDPA
Mobility

Count
er ID

Counter Name

Counter
Description
IntraFrequency
H2D Hard
Handovers
for Cell

67191 VS.HSDPA.HHO.H2D.AttOutInterFreq
159

NE

Featu
re ID

01061 Manageme
006
nt

Number of
BSC6 WRF
Inter900
DFrequency
01061
H2D Hard
006
Handover
Attempts for
Cell

67191 VS.HSDPA.HHO.H2D.SuccOutInterFreq Number of


160
Successful
InterFrequency
H2D Hard
Handovers
for Cell

Feature
Name

HSDPA
Mobility
Manageme
nt

BSC6 WRF
900
D01061
006

HSDPA
Mobility
Manageme
nt

67191 VS.HHO.AttBlindHO
694

Number of
BSC6 WRF
Outgoing
900
DEmergency
02030
Blind
2
Handover
Attempts for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage

67191 VS.HHO.SuccBlindHO
695

Number of
Successful
Outgoing
Emergency
Blind Hard
Handovers
for Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

BSC6 WRF
900
D02040
002

Inter
System
Direct
Retry

67192 IRATHO.FailRelocPrepOutCS.HigherTra Number of


186
fficLod
Failed
Preparations
for CS

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.FailRelocPrepInCS.TgtHigh Number of


BSC6 WRF
187
Load
Failed
900
DPreparations
02040
for CS
002
Incoming
WRF
Inter-RAT
DHandover
02030
(Traffic Load
3
In The Target
WRF
Cell Higher
DThan In The
02030
Source Cell)
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.HSUPA.SHO.AttOut
367

Number of
BSC6 WRF
EDCH RL
900
DAddition and
01061
Deletion
204
Attempts by
Soft
Handover for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.SHO.SuccOut
368

Number of
Successful
EDCH RL

Outgoing
Inter-RAT
Handover for
Cell (Traffic
Load In The
Target Cell
Higher Than
In The
Source Cell)

NE

BSC6 WRF HSUPA


900
DMobility
01061 Manageme

Count
er ID

Counter Name

Counter
Description
Additions
and
Deletions by
Soft
Handover for
Cell

NE

Featu
re ID
204

Feature
Name
nt

67192 VS.HSUPA.SHO.ServCellChg.SuccOut
369

Number of
Successful
HSUPA
Serving Cell
Changes in
Soft
Handover
Status for
Cell

BSC6 WRF
900
D01061
204

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.SHO.ServCellChg.AttOut
370

Number of
HSUPA
Serving Cell
Change
Attempts in
Soft
Handover
Status for
Cell

BSC6 WRF
900
D01061
204

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2E.SuccOutIntraFreq
371

Number of
BSC6 WRF
Successful
900
DHSUPA
01061
Serving Cell
204
Changes Due
to IntraFrequency
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2E.AttOutIntraFreq

Number of

HSUPA

BSC6 WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

372

HSUPA
900
Serving Cell
Change
Attempts
Due to IntraFrequency
Hard
Handover
without
Channel
Change for
Cell

67192 VS.HSUPA.HHO.E2E.SuccOutInterFreq
373

Number of
BSC6 WRF
Successful
900
DHSUPA
01061
Serving Cell
204
Changes Due
to InterFrequency
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2E.AttOutInterFreq
374

Number of
BSC6 WRF
HSUPA
900
DServing Cell
01061
Change
204
Attempts
Due to InterFrequency
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2D.SuccOutIntraFreq Number of

DMobility
01061 Manageme
204
nt

BSC6 WRF

HSUPA

Count
er ID

Counter Name

Counter
Description

NE

472

Successful
HSUPA
IntraFrequency
Hard
Handovers
for
Cell(EDCH
to DCH)

67192 VS.HSUPA.HHO.E2D.AttOutIntraFreq
473

Number of
BSC6 WRF
HSUPA
900
DIntra01061
Frequency
204
Hard
Handover
Attempts for
Cell(EDCH
to DCH)

67192 VS.HSUPA.HHO.E2D.SuccOutInterFreq Number of


474
Successful
HSUPA
InterFrequency
Hard
Handovers
for
Cell(EDCH
to DCH)
67192 VS.HSUPA.HHO.E2D.AttOutInterFreq
475

900

Featu
re ID

Feature
Name

DMobility
01061 Manageme
204
nt

HSUPA
Mobility
Manageme
nt

BSC6 WRF
900
D01061
204

HSUPA
Mobility
Manageme
nt

Number of
BSC6 WRF
HSUPA
900
DInter01061
Frequency
204
Hard
Handover
Attempts for
Cell(EDCH
to DCH)

HSUPA
Mobility
Manageme
nt

67192 VS.IRATHO.HSUPA.SuccOutPSUTRAN Number of

BSC6 WRF

HSUPA

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

506

Successful
900
PS Outgoing
Inter-RAT
Handovers
for HSUPA
Services for
Cell

DMobility
01061 Manageme
204
nt

67192 VS.IRATHO.HSUPA.AttOutPSUTRAN
507

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
01061
Handover
204
Attempts for
HSUPA
Services for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HHO.FailInterFreqOut.PrepFail
555

Number of
BSC6 WRF
Failed
900
DPreparations
02030
for Outgoing
2
InterWRF
Frequency
DHard
02030
Handovers
4
for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67192 VS.HHO.FailInterFreqOut.RLSetupFail
557

Number of
BSC6 WRF
Failed
900
DPreparations
02030
for Outgoing
2
InterWRF
Frequency
DHard
02030
Handovers
4
Due to Radio
Link
Establishmen
t Failure for

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67192 VS.LCC.LDR.HSUPA.InterRATPS
645

Number of
BSC6 WRF
HSUPA UEs 900
DPerforming
02030
PS Inter-RAT
6
Handover in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.AttRelocPrepOutCS.Sig
654

Number of
Preparations
for CS
Outgoing
Inter-RAT
Handover
When only
Signaling
Exists for
Cell

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.SuccRelocPrepOutCS.Sig
655

Number of
Successful
Preparations
for CS
Outgoing
Inter-RAT
Handover
When only
Signaling
Exists for
Cell

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.AttOutCS.Sig
656

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT

Cell

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

D02030
5
WRF
D02030
6

Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Inter-RAT
3
Handovers
WRF
When only
DSignaling
02030
Exists for
5
Cell
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 IRATHO.FailRelocPrepOutCS.NoResAva Number of


BSC6 WRF
658
il
Failed
900
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell (No
3
Resource
WRF
Available)
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

When only
Signaling
Exists for
Cell

67192 VS.IRATHO.SuccOutCS.Sig
657

67192 IRATHO.FailRelocPrepOutCS.UKnowR
659
NC

Number of
Failed
Preparations

NE

BSC6 WRF Inter


900
DSystem
02040 Direct

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Number of
BSC6 WRF
Times that
900
Dthe Timer
02040
Waiting for
002
Iu Release
WRF
Command
DExpires in
02030
CS Outgoing
3
Inter-RAT
WRF
Handover for
DCell
02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.FailOutPSUTRAN.NoReply Number of


BSC6 WRF
661
Times that
900
Dthe Timer
02030
Waiting for
3
Iu Release
WRF
Command
DExpires in PS
02030
Outgoing
5
Inter-RAT
WRF
Handover
D-

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover

for CS
Outgoing
Inter-RAT
Handover for
Cell
(Unknown
Target RNC)

67192 VS.IRATHO.FailOutCS.NoReply
660

NE

Count
er ID

Counter Name

Counter
Description
Initiated by
RNC for Cell

NE

Featu
re ID

Feature
Name

02030 Based on
6
Load

67192 VS.IRATHO.AttRelocPrepOutPS
662

Number of
BSC6 WRF
Preparations 900
Dfor Enhanced
02030
PS Outgoing
802
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocPrepOutPS
663

Number of
BSC6 WRF
Successful
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.AttRelocOutPS
664

Number of
BSC6 WRF
Enhanced PS 900
DOutgoing
02030
Inter-RAT
802
Handover
Attempts for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocOutPS
665

Number of
BSC6 WRF
Successful
900
DEnhanced PS
02030
Outgoing
802
Inter-RAT
Handovers
for Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.TAlEx Number of


BSC6 WRF
666
p
Failed
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Handover for
Cell
(TRELOCall
oc expiry)
67192 VS.IRATHO.FailRelocPrepOutPS.TgtFai Number of
BSC6 WRF
667
l
Failed
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell
(Relocation
Failure in
Target
CN/RNC or
Target
System)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.ReloU Number of


BSC6 WRF
668
nSupp
Failed
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell
(Relocation
not
supported in
Target RNC
or Target
system)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.TgtHig Number of


BSC6 WRF
669
hLoad
Failed
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Cell (Traffic
Load In The
Target Cell
Higher Than
In The
Source Cell)
67192 VS.IRATHO.FailRelocPrepOutPS.NoRes Number of
BSC6 WRF
670
Avail
Failed
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell (No
Resource
Available)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.UnKn
671
owRNC

Number of
BSC6 WRF
Failed
900
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell
(Unknown
Target RNC)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocOutPS.CfgUnSup
672
p

Number of
BSC6 WRF
Failed
900
DEnhanced PS
02030
Outgoing
802
Inter-RAT
Handovers
for Cell
(Configuratio
n
Unsupported
)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocOutPS.PhyChFail

Number of

PS

BSC6 WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

673

Failed
900
Enhanced PS
Outgoing
Inter-RAT
Handovers
for Cell
(Physical
Channel
Failure)

DHandover
02030 Between
802
UMTS and
GPRS

67192 VS.IRATHO.FailRelocOutPS.NoReply
674

Number of
BSC6 WRF
Times that
900
Dthe Timer
02030
Waiting for
802
Iu Release
Command
Expires in
Enhanced PS
Outgoing
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.AttRelocPrepInPS
675

Number of
BSC6 WRF
Preparations 900
Dfor Enhanced
02030
PS Incoming
802
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocPrepInPS
676

Number of
BSC6 WRF
Successful
900
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocInPS
677

Number of
Successful

PS
Handover

BSC6 WRF
900
D-

Count
er ID

Counter Name

Counter
Description
Enhanced PS
Incoming
Inter-RAT
Handovers
for Cell

NE

Featu
re ID

Feature
Name

02030 Between
802
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.TgtFail
678

Number of
BSC6 WRF
Failed
900
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
cell
(Relocation
failure in
target
CN/RNC or
target
system)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.ReloUn
679
Supp

Number of
BSC6 WRF
Failed
900
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
cell
(Relocation
not
supported in
target RNC
or target
system)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.ResUna
680
vail

Number of
BSC6 WRF
Failed
900
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Handover for
cell (No
resource
available)
67192 VS.IRATHO.FailRelocPrepInPS.TgtHigh Number of
BSC6 WRF
681
Load
Failed
900
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
cell (Traffic
Load In The
Target Cell
Higher Than
In The
Source Cell)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocInPS.NoReply
682

Number of
BSC6 WRF
Failed
900
DEnhanced PS
02030
Incoming
802
Inter-RAT
Handovers
Due to UE
Response
Timeout for
Cell

PS
Handover
Between
UMTS and
GPRS

67193 VS.HHO.InterFreqOut.CS.MeasTimeOut Number of


BSC6 WRF
397
Handovers
900
DNot
02030
Performed
2
Due to CS
WRF
InterDFrequency
02030
Measurement
4
Expiry for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67193 VS.HHO.InterFreqOut.PS.MeasTimeOut
398

Number of
BSC6 WRF
Handovers
900
DNot
02030
Performed
2
Due to PS
WRF
InterDFrequency
02030
Measurement
4
Expiry for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67193 VS.IRATHO.OutCS.MeasTimeOut
399

Number of
BSC6 WRF
CS Inter900
DRAT
02030
Measurement
3
Expiry for
WRF
Cell
D02030
9

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
DL QoS

67193 VS.IRATHO.OutPS.MeasTimeOut
400

Number of
BSC6 WRF
PS Inter-RAT 900
DMeasurement
02030
Expiry for
3
Cell
WRF
D02030
9

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
DL QoS

67193 VS.HHO.AttInterFreqOut.CS.TrigRscp
401

Number of
CS InterFrequency
Hard
Handover
Attempts
Based on
RSCP for
Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

67193 VS.HHO.AttInterFreqOut.CS.TrigEcNo

Number of

BSC6 WRF

Inter

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

402

CS InterFrequency
Hard
Handover
Attempts
Based on
EcNo for
Cell

900

DFrequency
02030 Hard
2
Handover
Based on
Coverage

67193 VS.HHO.AttInterFreqOut.PS.TrigRscp
403

Number of
PS InterFrequency
Hard
Handover
Attempts
Based on
RSCP for
Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

67193 VS.HHO.AttInterFreqOut.PS.TrigEcNo
404

Number of
PS InterFrequency
Hard
Handover
Attempts
Based on
EcNo for
Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

67193 VS.IRATHO.AttOutCS.TrigRscp
405

Number of
CS InterRAT
Handover
Attempts
Based on
RSCP for
Cell

BSC6 WRF
900
D02030
3

Inter-RAT
Handover
Based on
Coverage

67193 VS.IRATHO.AttOutCS.TrigEcNo
406

Number of
CS InterRAT
Handover

BSC6 WRF
900
D02030
3

Inter-RAT
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67193 VS.IRATHO.AttOutPS.TrigRscp
407

Number of
BSC6 WRF
PS Inter-RAT 900
DHandover
02030
Attempts
3
Based on
RSCP for
Cell

Inter-RAT
Handover
Based on
Coverage

67193 VS.IRATHO.AttOutPS.TrigEcNo
408

Number of
BSC6 WRF
PS Inter-RAT 900
DHandover
02030
Attempts
3
Based on
EcNo for
Cell

Inter-RAT
Handover
Based on
Coverage

67194 VS.CM.ULSF2.Act.Att
881

Number of
BSC6 WRF
Uplink SF-2 900
DCompression
02030
Mode
2
Activation
WRF
Requests for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.ULHLS.Act.Att
882

Number of
BSC6 WRF
Uplink HLS 900
DCompression
02030
Mode
2
Activation
WRF
Requests for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency

Attempts
Based on
EcNo for
Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Hard
Handover
Based on
DL QoS

67194 VS.CM.ULSF2.Act.Fail
883

Number of
BSC6 WRF
Uplink SF-2 900
DCompression
02030
Mode
2
Activation
WRF
Failures for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.ULHLS.Act.Fail
884

Number of
BSC6 WRF
Uplink HLS 900
DCompression
02030
Mode
2
Activation
WRF
Failures for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLSF2.Act.Att
885

Number of
BSC6 WRF
Downlink
900
DSF-2
02030
Compression
2
Mode
WRF
Activation
DRequests for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
DL QoS

67194 VS.CM.DLHLS.Act.Att
886

Number of
BSC6 WRF
Downlink
900
DHLS
02030
Compression
2
Mode
WRF
Activation
DRequests for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLSF2.Act.Fail
887

Number of
BSC6 WRF
Downlink
900
DSF-2
02030
Compression
2
Mode
WRF
Activation
DFailures for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLHLS.Act.Fail
888

Number of
BSC6 WRF
Downlink
900
DHLS
02030
Compression
2
Mode
WRF
Activation
DFailures for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67195 VS.HSDPA.SHO.ServCellChg.AttOutIur

Number of

HSDPA

BSC6 WRF

Count
er ID

Counter Name

481

Counter
Description

NE

Inter-RNC
900
HSDPA
Serving Cell
Change
Attempts for
Cell

67195 VS.HSDPA.SHO.ServCellChg.SuccOutIu Number of


482
r
Inter-RNC
HSDPA
Serving Cell
Change
Success for
Cell

Featu
re ID

Feature
Name

DMobility
01061 Manageme
006
nt

BSC6 WRF
900
D01061
006

HSDPA
Mobility
Manageme
nt

67195 VS.HSDPA.HHO.H2H.AttOutIur
483

Number of
BSC6 WRF
Inter-RNC
900
DHSDPA Hard
01061
Handover
006
Attempts
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67195 VS.HSDPA.HHO.H2H.SuccOutIur
484

Number of
BSC6 WRF
Successful
900
DInter-RNC
01061
HSDPA Hard
006
Handovers
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67195 VS.HSUPA.SHO.ServCellChg.AttOutIur
485

Number of
inter-RNC
HSUPA
Serving Cell
Change
Attempts in
Soft

HSUPA
Mobility
Manageme
nt

BSC6 WRF
900
D01061
204

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Handover
Status for
Cell
67195 VS.HSUPA.SHO.ServCellChg.SuccOutIu Number of
486
r
Successful
inter-RNC
HSUPA
Serving Cell
Changes in
Soft
Handover
Status for
Cell

BSC6 WRF
900
D01061
204

HSUPA
Mobility
Manageme
nt

67195 VS.HSUPA.HHO.E2E.SuccOutIur
487

Number of
BSC6 WRF
Successful
900
DHSUPA
01061
Serving Cell
204
Changes Due
to inter-RNC
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67195 VS.HSUPA.HHO.E2E.AttOutIur
488

Number of
BSC6 WRF
HSUPA
900
DServing Cell
01061
Change
204
Attempts
Due to interRNC Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67196 VS.LCC.LDR.HSUPA.InterRATCS

Number of

Inter-RAT

BSC6 WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

029

HSUPA UEs 900


Performing
CS InterRAT
Handovers in
Basic
Congestion
for Cell

67196 VS.LCC.LDR.HSDPA.InterRATCS
030

Number of
BSC6 WRF
HSDPA UEs 900
DPerforming
02030
CS Inter6
RAT
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67203 VS.RAB.ModReqCS.VP.Fallback.RNC
800

Number of
VP Services
Fallen Back
to AMR
Services for
RNC

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6
WRF
D02120
0

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load
HCS
(Hierarchic
al Cell
Structure)

BSC6 WRF
900
D02030
2
WRF
D-

Inter
Frequency
Hard
Handover
Based on
Coverage

73393 VS.HHO.FailInterFreqOut.InterRNC.Cfg Number of


853
Unsupp
Failed
Outgoing
InterFrequency
Hard

DHandover
02030 Based on
6
Load

Count
er ID

Counter Name

Counter
Description
Handovers
Between the
RNCs for
Cell
(Configuratio
n
Unsupported
)

73393 VS.HHO.FailInterFreqOut.InterRNC.Phy Number of


854
ChFail
Failed
Outgoing
InterFrequency
Hard
Handovers
Between the
RNCs for
Cell
(Physical
Channel
Failure)

NE

Featu
re ID

Feature
Name

02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailInterFreqOut.InterRNC.ISR Number of


BSC6 WRF
855
Failed
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between the
4
RNCs for
Cell
(Incompatibl
e
Simultaneous
Reconfigurat
ion)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailInterFreqOut.InterRNC.Inv
856
Cfg

Number of
Failed
Outgoing

BSC6 WRF Inter


900
DFrequency
02030 Hard

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

InterFrequency
Hard
Handovers
Between the
RNCs for
Cell (Invalid
Configuratio
n)

2
WRF
D02030
4

Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailInterFreqOut.InterRNC.Cell Number of


857
Updt
Failed
Outgoing
InterFrequency
Hard
Handovers
Between the
RNCs for
Cell (Cell
Update
Occurred)

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailInterFreqOut.InterRNC.No
858
Reply

Number of
BSC6 WRF
Failed
900
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between the
4
RNCs Due to
No Response
from the UE
for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.IRATHO.AttOutCS.TrigDLTxp
923

Number of
BSC6 WRF
CS Inter900
DRAT
02030
Handover
9
Attempts
Based on DL

Inter-RAT
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.IRATHO.AttOutPS.TrigDLTxp
925

Number of
BSC6 WRF
PS Inter-RAT 900
DHandover
02030
Attempts
9
Based on DL
Code Power
for Cell

Inter-RAT
Handover
Based on
DL QoS

73393 VS.IRATHO.SuccOutCS.TrigRscp
926

Number of
Successful
CS InterRAT
Handovers
Based on
RSCP for
Cell

BSC6 WRF
900
D02030
3

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutCS.TrigEcNo
927

Number of
Successful
CS InterRAT
Handovers
Based on
EcNo for
Cell

BSC6 WRF
900
D02030
3

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutCS.TrigDLTxp
929

Number of
BSC6 WRF
Successful
900
DCS Inter02030
RAT
9
Handovers
Based on DL
Code Power
for Cell

Inter-RAT
Handover
Based on
DL QoS

73393 VS.IRATHO.SuccOutPS.TrigRscp
930

Number of
BSC6 WRF
Successful
900
DPS Inter-RAT
02030
Handovers
3

Inter-RAT
Handover
Based on
Coverage

Code Power
for Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.IRATHO.SuccOutPS.TrigEcNo
931

Number of
BSC6 WRF
Successful
900
DPS Inter-RAT
02030
Handovers
3
Based on
EcNo for
Cell

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutPS.TrigDLTxp
933

Number of
BSC6 WRF
Successful
900
DPS Inter-RAT
02030
Handovers
9
Based on DL
Code Power
for Cell

Inter-RAT
Handover
Based on
DL QoS

73393 VS.HHO.AttInterFreqOut.CS.Tcp
937

Number of
BSC6 WRF
CS Inter900
DFrequency
02030
Hard
4
Handover
Attempts
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.AttInterFreqOut.PS.Tcp
938

Number of
BSC6 WRF
PS Inter900
DFrequency
02030
Hard
4
Handover
Attempts
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

Based on
RSCP for
Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.HHO.SuccInterFreqOut.CS.Tcp
948

Number of
BSC6 WRF
Successful
900
DCS Inter02030
Frequency
4
Hard
Handovers
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.SuccInterFreqOut.PS.Tcp
949

Number of
BSC6 WRF
Successful
900
DPS Inter02030
Frequency
4
Hard
Handovers
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HSUPA.TTI2to10.Att
984

Number of
BSC6 WRF
TTI Switch 900
DAttempts
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(2ms to
01061
10ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HSUPA.TTI2to10.Succ
985

Number of
BSC6 WRF
Successful
900
DTTI Switches
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(2ms to
01061
10ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.HSUPA.TTI10to2.Att
986

Number of
BSC6 WRF
TTI Switch 900
DAttempts
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(10ms to
01061
2ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HSUPA.TTI10to2.Succ
987

Number of
BSC6 WRF
Successful
900
DTTI Switches
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(10ms to
01061
2ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HHO.AttOutIntraNodeB.CS.NCell
988

Number of
BSC6 WRF
CS Outgoing 900
DIntra-NodeB
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.SuccOutIntraNodeB.CS.NCell
989

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Intra-NodeB
1
Inter-Cell
WRF

Intra
Frequency
Hard
Handover
Inter

Count
er ID

Counter Name

Counter
Description
Hard
Handovers

NE

Featu
re ID

Feature
Name

D02030
2
WRF
D02030
4

Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.NoReply.C
990
S.NCell

Number of
Failed CS
Outgoing
Intra-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.PhyChFail.
991
CS.NCell

Number of
Failed CS
Outgoing
Intra-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Handover
Based on
DL QoS

73393 VS.HHO.AttOutIntraNodeB.PS.NCell
992

Number of
BSC6 WRF
PS Outgoing 900
DIntra-NodeB
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.SuccOutIntraNodeB.PS.NCell
993

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Intra-NodeB
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.NoReply.PS Number of


994
.NCell
Failed PS
Outgoing
Intra-NodeB

BSC6 WRF
900
D02030
1

Intra
Frequency
Hard
Handover

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.AttOutInterNodeBIntraRNC.CS Number of


BSC6 WRF
996
.NCell
CS Outgoing 900
DIntra-RNC
02030
Inter-NodeB
1
Inter-Cell
WRF
Hard
DHandover
02030
Attempts
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency

Inter-Cell
Hard
Handovers
(UE No
Response)

73393 VS.HHO.FailOutIntraNodeB.PhyChFail.
995
PS.NCell

Number of
Failed PS
Outgoing
Intra-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Hard
Handover
Based on
DL QoS

73393 VS.HHO.SuccOutInterNodeBIntraRNC.
997
CS.NCell

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Intra-RNC
1
Inter-NodeB
WRF
Inter-Cell
DHard
02030
Handovers
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutInterNodeBIntraRNC.N Number of


998
oReply.CS.NCell
Failed CS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

73393 VS.HHO.FailOutInterNodeBIntraRNC.P
999
hyChFail.CS.NCell

BSC6 WRF Intra


900
DFrequency
02030 Hard

Number of
Failed CS
Outgoing

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

1
WRF
D02030
2
WRF
D02030
4

Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.AttOutInterNodeBIntraRNC.PS Number of


BSC6 WRF
000
.NCell
PS Outgoing 900
DIntra-RNC
02030
Inter-NodeB
1
Inter-Cell
WRF
Hard
DHandover
02030
Attempts
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.SuccOutInterNodeBIntraRNC.P Number of


BSC6 WRF
001
S.NCell
Successful
900
DPS Outgoing
02030
Intra-RNC
1
Inter-NodeB
WRF
Inter-Cell
DHard
02030
Handovers
2
WRF
D-

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage

Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS
73394 VS.HHO.FailOutInterNodeBIntraRNC.N Number of
002
oReply.PS.NCell
Failed PS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterNodeBIntraRNC.P
003
hyChFail.PS.NCell

Number of
Failed PS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.AttOutInterRNCIur.CS.NCell

Number of

BSC6 WRF

Intra

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

004

CS Outgoing 900
Inter-RNC
Inter-Cell
Hard
Handover
Attempts

D02030
1
WRF
D02030
2
WRF
D02030
4

Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.SuccOutInterRNCIur.CS.NCell
005

Number of
BSC6 WRF
Successful
900
DCS Outgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterRNCIur.CfgUnsup. Number of


BSC6 WRF
006
CS.NCell
Failed CS
900
DOutgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
(Configuratio
2
n

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
4

Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

BSC6 WRF
900
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Number of
BSC6 WRF
PS Outgoing 900
DInter-RNC
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Unsupported
)

73394 VS.HHO.FailOutInterRNCIur.PhyChFail. Number of


007
CS.NCell
Failed CS
Outgoing
Inter-RNC
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

73394 VS.HHO.AttOutInterRNCIur.PS.NCell
008

NE

Count
er ID

Counter Name

Featu
re ID

Feature
Name

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterRNCIur.CfgUnsup. Number of


BSC6 WRF
010
PS.NCell
Failed PS
900
DOutgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
(Configuratio
2
n
WRF
Unsupported
D)
02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterRNCIur.PhyChFail. Number of


011
PS.NCell
Failed PS
Outgoing
Inter-RNC
Inter-Cell
Hard
Handovers
(Physical

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover

73394 VS.HHO.SuccOutInterRNCIur.PS.NCell
009

Counter
Description

NE

BSC6 WRF
900
D02030
1
WRF
D02030
2

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
4

Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Number of
BSC6 WRF
CS Incoming 900
DInter-RAT
02040
Handover
002
Attempts for
WRF
Cell
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Channel
Failure)

73394 VS.IRATHO.AttInCS
014

NE

73394 VS.IRATHO.FailRelocPrepOutCS.Cancel Number of


015
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
for Cell
(Relocation
Cancelled)

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.CNNo Number of


016
Reply
Failed CS

BSC6 WRF
900
D-

Inter-RAT
Handover

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02030
3
WRF
D02030
5
WRF
D02030
6

Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepInCS.Abort
017

Number of
BSC6 WRF
CS Incoming 900
DInter-RAT
02030
Handover
3
Preparation
WRF
Failures for
DCell (Iu
02030
RELEASE
5
COMMAND
WRF
Received)
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailOutCS.Abort
018

Number of
BSC6 WRF
Abnormally 900
DTerminated
02030
CS Outgoing
3
Inter-RAT
WRF
Handovers
Dfor Cell
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.Abort
019

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02030
Handover
3

Inter-RAT
Handover
Based on
Coverage

Outgoing
Inter-RAT
Handover
Preparations
for Cell
(Relocation
Command
Wait
Timeout)

NE

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.ReqInf Number of


020
oNotAvail
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
for Cell
(Requested
Information
Not
Available)

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailOutPS
021

Number of
Failed PS
Outgoing
Inter-RAT
Handovers
Initiated by
the RNC for
Cell

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailOutPS.Abort
022

Number of
BSC6 WRF
Abnormally 900
DTerminated
02030
PS Outgoing
3
Inter-RAT
WRF
Handovers
Dfor Cell

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover

Preparation
Failures for
Cell (Iu
RELEASE
COMMAND
Received)

NE

Count
er ID

Counter Name

Featu
re ID

Feature
Name

02030
5
WRF
D02030
6

Based on
Service
Inter-RAT
Handover
Based on
Load

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02030
Handover
3
Preparation
WRF
Attempts
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.AttRelocPrepOutCS.DR.GC Number of


BSC6 WRF
035
ell
CS Outgoing 900
DInter-RAT
02040
Handover
002
Preparation
WRF
Attempts
D(Directed
02030
retry)
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.AttRelocPrepOutCS.RF.GC Number of


036
ell
Failed CS
Outgoing
Inter-RAT

Inter-RAT
Handover
Based on
Coverage

73394 VS.IRATHO.AttRelocPrepOutCS.GCell
034

Counter
Description

NE

BSC6 WRF
900
D02030
3

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73394 VS.IRATHO.SuccRelocPrepOutCS.GCell Number of


BSC6 WRF
037
Successful
900
DCS Outgoing
02030
Inter-RAT
3
Handover
WRF
Preparations
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.TAlEx Number of


BSC6 WRF
038
p.GCell
Failed CS
900
DOutgoing
02030
Inter-RAT
3
Handover
WRF
Preparations
D(TRELOCall
02030
oc expiry)
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.TgtFai Number of


039
l.GCell
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
(Relocation
Failure in
Target

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service

Handover
Preparations
(Relocation
desirable for
radio
reasons)

BSC6 WRF
900
D02030
3
WRF
D02030
5

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
6

Inter-RAT
Handover
Based on
Load

73403 VS.HSDPA.HHO.H2D.AttOutIur
764

number of
BSC6 WRF
Inter-RNC
900
DH2D Hard
01061
Handover
006
Attempts for
Cell

HSDPA
Mobility
Manageme
nt

73403 VS.HSDPA.HHO.H2D.SuccOutIur
765

Number of
Successful
Inter-RNC
H2D Hard
Handovers
for Cell

BSC6 WRF
900
D01061
006

HSDPA
Mobility
Manageme
nt

73403 VS.HSUPA.HHO.E2D.AttOutIur
766

Number of
BSC6 WRF
inter-RNC
900
DHSUPA Hard
01061
Handover
204
Attempts for
Cell(EDCH
to DCH)

HSUPA
Mobility
Manageme
nt

73403 VS.HSUPA.HHO.E2D.SuccOutIur
767

Number of
BSC6 WRF
Successful
900
Dinter-RNC
01061
HSUPA Hard
204
Handovers
for
Cell(EDCH
to DCH)

HSUPA
Mobility
Manageme
nt

73403 VS.HHO.AttInterFreqIn.CS
768

Number of
BSC6 WRF
Requests for 900
DCS Incoming
02030
Inter2
Frequency
WRF
Hard
D-

Inter
Frequency
Hard
Handover
Based on
Coverage

CN/RNC or
Target
System)

NE

Count
er ID

Counter Name

Counter
Description
Handovers
for Cell

NE

Featu
re ID

Feature
Name

02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.AttInterFreqIn.PS
769

Number of
BSC6 WRF
Requests for 900
DPS Incoming
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.AttInterFreqOut.CS
770

Number of
BSC6 WRF
Requests for 900
DCS Outgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.AttInterFreqOut.PS
771

Number of
BSC6 WRF
Requests for 900
DPS Outgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqIn.CS
772

Number of
Successful
for CS
Incoming
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqIn.PS
773

Number of
Successful
for PS
Incoming
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqOut.CS
774

Number of
Successful
for CS
Outgoing
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73403 VS.HHO.SuccInterFreqOut.PS
775

Number of
Successful
for PS
Outgoing
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.InterFreqOut.CS.Drop
776

Number of
BSC6 WRF
CS Call
900
DDrops due to
02030
Unsuccessful
2
Outgoing
WRF
InterDFrequency
02030
Hard
4
Handovers
for cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.InterFreqOut.PS.Drop
777

Number of
BSC6 WRF
PS Call
900
DDrops due to
02030
Unsuccessful
2
Outgoing
WRF
InterDFrequency
02030
Hard
4
Handovers
for cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73404 VS.HHO.SuccInterFreqOut.CS.Rscp
081

Number of
Successful
CS Inter-

BSC6 WRF Inter


900
DFrequency
02030 Hard

Count
er ID

Counter Name

Counter
Description
Frequency
Hard
Handovers
Based on
RSCP for
Cell

NE

Featu
re ID
2

Feature
Name
Handover
Based on
Coverage

73404 VS.HHO.SuccInterFreqOut.CS.EcNo
082

Number of
Successful
CS InterFrequency
Hard
Handovers
Based on
EcNo for
Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

73404 VS.HHO.SuccInterFreqOut.PS.Rscp
083

Number of
Successful
PS InterFrequency
Hard
Handovers
Based on
RSCP for
Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

73404 VS.HHO.SuccInterFreqOut.PS.EcNo
084

Number of
Successful
PS InterFrequency
Hard
Handovers
Based on
EcNo for
Cell

BSC6 WRF
900
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

73423 VS.IRATHO.FailOutPS.UEGen
107

Number of
Failed
Outgoing
UMTS-toGSM PS

BSC6 WRF
900
D02030
3
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT

Count
er ID

Counter Name

Counter
Description
Handovers
due to UE
Reselection
Back to a
UTRAN Cell

NE

Featu
re ID

Feature
Name

D02030
5
WRF
D02030
6

Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73423 VS.SRVCC.U2GERAN.AttRelocPrepOut Number of


BSC6 WRF
288
PS
Outgoing
900
DInter-RAT PS
02030
Handover
802
Preparation
Attempts
Triggered by
SRVCC for
VoIP
Services for
Cell

PS
Handover
Between
UMTS and
GPRS

73423 VS.SRVCC.U2GERAN.SuccRelocPrepO Number of


BSC6 WRF
289
utPS
Successful
900
DOutgoing
02030
Inter-RAT PS
802
Handover
Preparations
Triggered by
SRVCC for
VoIP
Services for
Cell

PS
Handover
Between
UMTS and
GPRS

73423 VS.SRVCC.U2GERAN.SuccRelocOutPS Number of


BSC6 WRF
290
Successful
900
DOutgoing
02030
Inter-RAT PS
802
Handovers
Triggered by
SRVCC for
VoIP
Services for
Cell

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73424 VS.HSUPA.TTI2to10.ADMCE.Succ
209

Number of
BSC6 WRF
Successful
900
DTTI
01061
Switchovers
404
Based on
Admitted
CEs During
RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

73424 VS.HSUPA.TTI2to10.COVER.Succ
210

Number of
BSC6 WRF
Successful
900
DTTI
01069
Switchovers
0
Based on
WRF
Coverage
DDuring RB
01061
Reconfigurat
404
ion in a
Cell(2ms to
10ms)

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73424 VS.HSUPA.TTI2to10.ResRTWP.Succ
211

Number of
BSC6 WRF
Successful
900
DTTI
01061
Switchovers
404
Based on
RTWP
During RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

73424 VS.HSUPA.TTI2to10.ResUsedCE.Succ
212

Number of
Successful
TTI
Switchovers
Based on

HSUPA
2ms/10ms
TTI
Handover

BSC6 WRF
900
D01061
404

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73424 VS.HSUPA.TTI2to10.ResIUB.Succ
471

Number of
BSC6 WRF
Successful
900
DTTI
01061
Switchovers
404
Based on Iub
Resources
During RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

73425 VS.IRATHO.FailOutCS.SCRI
007

Number of
BSC6 WRF
Failed CS
900
DOutgoing
02030
Inter-RAT
3
Handovers
WRF
for
DCell(Signalli
02030
ng
5
Connection
WRF
Release
DIndication)
02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutPSUTRAN.SCRI
008

Number of
BSC6 WRF
Failed PS
900
DOutgoing
02030
Inter-RAT
3
Handovers
WRF
for
DCell(Signalli
02030
ng
5

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service

Number of
Occupied
CEs During
RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
6

Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutPSUTRAN.NoSRN
009
SDataForwardCmd

Number of
BSC6 WRF
Failed PS
900
DOutgoing
02030
Inter-RAT
3
Handovers
WRF
for Cell(No
DSRNS DATA
02030
Forward
5
cmd)
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.AttOutPSUTRAN.Sig
010

Number of
BSC6 WRF
PS Outgoing 900
DInter-RAT
02030
Handover
3
Attempts
WRF
When only
DSignaling
02030
Exists for
5
Cell
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.SuccOutPSUTRAN.Sig
011

Number of
BSC6 WRF
Successful
900
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF
When only
DSignaling
02030
Exists for
5
Cell
WRF
D-

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover

Connection
Release
Indication)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Based on
6
Load
73425 VS.IRATHO.FailOutCS.InterRatRF
012

Number of
Failed CS
Outgoing
Inter-RAT
Handovers
for
Cell(Failure
in the Radio
Interface
Procedure)

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutPSUTRAN.InterRat
013
RF

Number of
Failed PS
Outgoing
Inter-RAT
Handovers
for
Cell(Failure
in the Radio
Interface
Procedure)

BSC6 WRF
900
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.HHO.AttInterFreqOut.Sig
014

Number of
InterFrequency
Hard
Handover
Attempts
When only
Signaling
Exists for
Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73425 VS.HHO.SuccInterFreqOut.Sig
015

Number of
Successful
InterFrequency
Hard
Handover
Attempts
When only
Signaling
Exists for
Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73425 VS.MultiRAB.PSAbnormRel.ResumeEx
016
p

Number of
BSC6 WRF
Abnormal PS 900
DService
02030
Releases in
3
the Case of
WRF
Multi-RAB
DServices for
02030
Cell during
5
an inter-RAT
WRF
handover( PS
DResume
02030
Timer
6
Expiry)

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHOCS.Cancel.ReEstab
926

Number of
BSC6 WRF
RL
900
DReestablishm
02030
ent Attempts
3
After UEs
WRF
Failed to
DReceive the
02030
CS Outgoing
6
Inter-RAT
WRF
Handover
DCommand
02030
for Cell
5

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Load
Inter-RAT
Handover
Based on
Service

73425 VS.IRATHOPS.Cancel.ReEstab
927

Number of
RL

Inter-RAT
Handover

BSC6 WRF
900
D-

Count
er ID

Counter Name

Counter
Description
Reestablishm
ent Attempts
After UEs
Failed to
Receive the
PS Outgoing
Inter-RAT
Handover
Command
for Cell

NE

Featu
re ID

Feature
Name

02030
3
WRF
D02030
6
WRF
D02030
5

Based on
Coverage
Inter-RAT
Handover
Based on
Load
Inter-RAT
Handover
Based on
Service

73425 VS.IRATHO.AttNACC
954

Number of
BSC6 WRF
Attempts to 900
DObtain GSM
02030
System
801
Information
MRF
during RIMDbased
09021
NACCs
1
Triggered by
Inter-RAT PS
Handovers
for Cell

NACC(Net
work
Assisted
Cell
Change)
eCoordinat
or based
RIM
process
optimizatio
n

73425 VS.IRATHO.SuccNACC
955

Number of
BSC6 WRF
Successful
900
DThat GSM
02030
System
801
Information
MRF
Is Obtained
Dduring RIM09021
based
1
NACCs
Triggered by
Inter-RAT PS
Handovers
for Cell

NACC(Net
work
Assisted
Cell
Change)
eCoordinat
or based
RIM
process
optimizatio
n

73426 VS.IRATHO.FailOutCS.CNUnspecFail
856

Number of
Failed
Outgoing
Inter-RAT

Inter
System
Direct
Retry

BSC6 WRF
900
D02040
002

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73426 VS.IRATHO.FailOutPSUTRAN.CNUnsp Number of


BSC6 WRF
857
ecFail
Failed
900
DOutgoing
02040
Inter-RAT PS
002
Handovers
WRF
Due to
DAbnormal
02030
Connection
3
Release by
WRF
CN for Cell
D(Unspecified
02030
Failure)
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73426 VS.IRATHO.AttOutMultiRABCSPS
858

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on

CS
Handovers
Due to
Abnormal
Connection
Release by
CN for Cell
(Unspecified
Failure)

NE

Number of
BSC6 WRF
Inter-RAT
900
DHandover
02040
Attempts
002
Initiated by
WRF
CS+PS (One
Dor Multiple)
02030
Combined
3
Services for
WRF
Cell
D02030

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

5
WRF
D02030
6

Service
Inter-RAT
Handover
Based on
Load

73426 VS.IRATHO.SuccOutMultiRABCSPS
859

Number of
BSC6 WRF
Successful
900
DInter-RAT
02040
Handovers
002
Initiated by
WRF
CS+PS (One
Dor Multiple)
02030
Combined
3
Services for
WRF
Cell
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73428 IRATHO.AttOutCS.Retry
084

Number of
BSC6 WRF
CS Outgoing 900
DInter-RAT
02040
Handover
002
Reattempts
WRF
for Cell
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73428 IRATHO.AttOutPSUTRAN.Retry

Number of

Inter-RAT

BSC6 WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

085

PS Outgoing 900
Inter-RAT
Handover
Reattempts
for Cell

D02030
3
WRF
D02030
5
WRF
D02030
6

Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73428 VS.HHO.AttInterFreqOut.CSPS
086

Number of
BSC6 WRF
Outgoing
900
DInter02030
frequency
2
Hard
WRF
Handover
DAttempts for
02030
CS+PS
4
Combined
Services for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73428 VS.HHO.SuccInterFreqOut.CSPS
087

Number of
Successful
Outgoing
Interfrequency
Hard
Handovers
for CS+PS
Combined
Services for
Cell

BSC6 WRF
900
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73428 VS.HSPA.ServCellChg.1A1COptTrig
444

Number of
HSPA
Serving Cell
Changes

BSC6 WRF
900
D01061
006

HSDPA
Mobility
Manageme
nt

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D01061
204

HSUPA
Mobility
Manageme
nt

73428 VS.HSPA.ServCellChg.1DOptTrig
445

Number of
BSC6 WRF
HSPA
900
DServing Cell
01061
Changes
006
Triggered by
WRF
Event 1D for
DCell
01061
204

HSDPA
Mobility
Manageme
nt
HSUPA
Mobility
Manageme
nt

73428 VS.CM.DLSF2.AltScramCode.UE.Max
665

Max Number BSC6 WRF


Of Ues with 900
DSf2AltScram
02030
Code In a
2
Cell
WRF
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

73428 VS.CM.DLSF2.UE.Max
668

Max Number BSC6 WRF


Of Ues with 900
DSf2 In a Cell
02030
2
WRF
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

73444 VS.CM.DLSF2.AltScramCode.UE.Mean
434

Average
BSC6 WRF
Number of
900
DUes with
02030
Sf2AltScram
2
Code in a
WRF
cell
D-

Inter
Frequency
Hard
Handover
Based on
Coverage

Triggered by
Event 1A or
1C for Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Inter-RAT
3
Handover
Based on
Coverage
73444 VS.CM.DLSF2.UE.Mean
435

Average
BSC6 WRF
Number Of 900
DUes with Sf2
02030
In a Cell
2
WRF
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

67175 VS.HHO.AttInterFreq.RNC
428

Number of
InterFrequency
Hard
Handover
Requests for
RNC

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67175 VS.HHO.SuccInterFreq.RNC
429

Number of
Successful
InterFrequency
Hard
Handovers
for RNC

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67175 VS.IRATHO.AttOutCS.RNC
945

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts for
WRF
RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.AttInCS.RNC
008

Number of
BSC6 WRF
CS Incoming 910
DInter-RAT
02030
Handover
3
Attempts for
WRF
RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.AttOutPSUTRAN.RNC
098

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts
WRF
Initiated by
DRNC for
02030
RNC
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.SuccOutPSUTRAN.RNC
100

Number of
Successful

Inter-RAT
Handover

BSC6 WRF
910
D-

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02030
3
WRF
D02030
5
WRF
D02030
6

Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67176 VS.IRATHO.SuccOutPSUE.RNC
102

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF
Initiated by
DUE for RNC
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67180 VS.HHO.InterFreqOut.Eval.CM
551

Number of
BSC6 WRF
Decisions for 910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers in
02030
Compressed
4
Mode for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.HHO.AttIn
565

Number of
BSC6 WRF
Incoming
910
DHard
02030
Handover
1
Attempts for

Intra
Frequency
Hard
Handover

PS Outgoing
Inter-RAT
Handovers
Initiated by
RNC for
RNC

NE

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.HHO.SuccIn
566

Number of
BSC6 WRF
Successful
910
DIncoming
02030
Hard
1
Handovers in
WRF
the RNC for
DCell
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.HHO.InterFreqIn.Eval.CM
570

Number of
BSC6 WRF
Decisions for 910
DIncoming
02030
Inter2
Frequency
WRF
Hard
DHandovers in
02030
Compressed
4
Mode for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67180 VS.RRC.MrRpt.2D
613

Number of
BSC6 WRF
Event 2D
910
DMeasurement
02030
Reports for
2
Cell
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67180 VS.RRC.MrRpt.2F
614

Number of
BSC6 WRF
Event 2F
910
DMeasurement
02030
Reports for
2
Cell
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.AttOut.NCell
489

Number of
Hard
Handovers
Attempts
Between
Neighboring
Cells

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67183 VS.HHO.SuccOut.NCell
490

Number of
Successful
Hard
Handovers
Between
Neighboring
Cells

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.IRATHO.AttOutCS.GCell
495

Number of
CS InterRAT
Outgoing
Handover
Attempts
Between
Neighboring
Cells

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.IRATHO.SuccOutCS.GCell
496

Number of
Successful
CS InterRAT
Outgoing
Handovers
Between
Neighboring
Cells

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID
6

Feature
Name
Load

67183 VS.IRATHO.AttOutPSUTRAN.GCell
497

Number of
BSC6 WRF
PS Inter-RAT 910
DOutgoing
02030
Handover
3
Attempts
WRF
Between
DNeighboring
02030
Cells
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.IRATHO.SuccOutPSUTRAN.GCell
498

Number of
BSC6 WRF
Successful
910
DPS Inter-RAT
02030
Outgoing
3
Handovers
WRF
Between
DNeighboring
02030
Cells
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67183 VS.HHO.AttInterFreqOut
900

Number of
BSC6 WRF
Outgoing
910
DInter02030
Frequency
2
Hard
WRF
Handover
DAttempts for
02030
Cell
4
WRF
D02010
6

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS
Load

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Reshufflin
g

67183 VS.HHO.SuccInterFreqOut
901

Number of
Successful
Outgoing
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4
WRF
D02010
6

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS
Load
Reshufflin
g

67183 VS.HHO.FailInterFreqOut.CfgUnsupp
902

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4
(Configuratio
n
Unsupported
)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.PyhChFail
903

Number of
Failed
Outgoing
InterFrequency
Hard
Handovers
for Cell
(Physical
Channel

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover

BSC6 WRF
910
D02030
2
WRF
D02030
4

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Failure)

Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.ISR
904

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4
(Incompatibl
e
Simultaneous
Reconfigurat
ion)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.CellUpdt
906

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell (Cell
4
Update
Occurred)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.FailInterFreqOut.InvCfg
907

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4
(Invalid
Configuratio
n)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67183 VS.HHO.FailInterFreqOut.NoReply
908

Number of
Failed
Outgoing
InterFrequency
Hard
Handovers
Due to No
Response
from the UE
for Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.AttInterFreqIn
912

Number of
BSC6 WRF
Incoming
910
DInter02030
Frequency
2
Hard
WRF
Handover
DAttempts for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67183 VS.HHO.SuccInterFreqIn
913

Number of
Successful
Incoming
InterFrequency
Hard
Handovers
for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67189 VS.HHO.EvalOut
722

Number of
BSC6 WRF Intra
Decisions for 910
DFrequency
Outgoing
02030 Hard

BSC6 WRF
910
D02030
2
WRF
D02030
4

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

1
WRF
D02030
2
WRF
D02030
4

Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67189 VS.HHO.EvalIn
723

Number of
BSC6 WRF
Decisions for 910
DIncoming
02030
Hard
1
Handovers
WRF
for Cell
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67189 VS.IRATHO.AttRelocPrepOutCS.Load
739

Number of
BSC6 WRF
Preparation 910
DAttempts for
02030
CS Outgoing
6
Inter-RAT
Handover
Initiated by
UTRAN
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

Hard
Handovers
for Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67189 VS.IRATHO.SuccRelocPrepOutCS.Load
740

Number of
BSC6 WRF
Successful
910
DPreparations
02030
for CS
6
Outgoing
Inter-RAT
Handover
Initiated by
UTRAN
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.SuccOutCS.Load
741

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Inter-RAT
6
Handovers
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.AttOutPSUTRAN.Load
742

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
6
Attempts
Initiated by
UTRAN
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.SuccOutPSUTRAN.Load
743

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RAT
6
Handovers
Initiated by
UTRAN
Based on
Load for Cell

Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.AttRelocPrepOutCS.RF
744

Number of
Preparation

Inter-RAT
Handover

BSC6 WRF
910
D-

Count
er ID

Counter Name

Counter
Description
Attempts for
CS Outgoing
Inter-RAT
Handover
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

NE

Featu
re ID

Feature
Name

02030 Based on
3
Coverage

67189 VS.IRATHO.SuccRelocPrepOutCS.RF
745

Number of
BSC6 WRF
Successful
910
DPreparations
02030
for CS
3
Outgoing
Inter-RAT
Handover
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 VS.IRATHO.SuccOutCS.RF
746

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Inter-RAT
3
Handovers
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 VS.IRATHO.AttOutPSUTRAN.RF
747

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts
Initiated by
the RNC
Based on RF

Inter-RAT
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67189 VS.IRATHO.SuccOutPSUTRAN.RF
748

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RAT
3
Handovers
Initiated by
the RNC
Based on RF
(Coverage,
QoS, or
HCS) for
Cell

Inter-RAT
Handover
Based on
Coverage

67189 IRATHO.AttRelocPrepOutCS
749

Number of
BSC6 WRF
Preparation 910
DAttempts for
02040
CS Outgoing
002
Inter-RAT
WRF
Handover for
DCell
02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.SuccRelocPrepOutCS
750

Number of
BSC6 WRF
Successful
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on

(Coverage,
QoS, or
HCS) for
Cell

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailRelocPrepOutCS.TAlExp
751

Number of
BSC6 WRF
Failed
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
(TRELOCall
WRF
oc expiry)
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailRelocPrepOutCS.TgtFail
752

Number of
BSC6 WRF
Failed
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
(Relocation
WRF
Failure in
DTarget
02030
CN/RNC or
5
Target
WRF
System)
D-

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover

Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Based on
6
Load
67189 IRATHO.FailRelocPrepOutCS.ReloNoSu Number of
BSC6 WRF
753
p
Failed
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
(Relocation
WRF
not
Dsupported in
02030
Target RNC
5
or Target
WRF
system)
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.AttOutCS
754

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02040
Handover
002
Attempts
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.SuccOutCS
755

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02040
Inter-RAT
002

Inter
System
Direct
Retry

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailOutCS.CfgUnsupp
756

Number of
BSC6 WRF
Failed CS
910
DOutgoing
02040
Inter-RAT
002
Handovers
WRF
for Cell
D(Configuratio
02030
n
3
Unsupported
WRF
)
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.FailOutCS.PhyChFail
757

Number of
Failed CS
Outgoing
Inter-RAT
Handovers
for Cell
(Physical
Channel
Failure)

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on

Handovers
for Cell

NE

BSC6 WRF
910
D02040
002
WRF
D02030
3
WRF
D02030

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

5
WRF
D02030
6

Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.AttRelocPrepInCS
758

Number of
BSC6 WRF
Preparations 910
Dfor CS
02040
Incoming
002
Inter-RAT
WRF
Handover for
DCell
02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.SuccInCS
759

Number of
BSC6 WRF
Successful
910
DCS Incoming
02040
Inter-RAT
002
Handovers
WRF
for Cell
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.FailRelocPrepInCS.TRNCS Number of

NE

BSC6 WRF

Inter

Count
er ID

Featu
re ID

Feature
Name

D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

BSC6 WRF
910
D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.IRATHO.FailRelocPrepInCS.ResUna Number of


BSC6 WRF
762
vail
Failed
910
DPreparations
02040
for CS
002
Incoming
WRF
Inter-RAT
DHandover
02030
(No resource
3

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage

760

Counter Name
ysFailReloc

Counter
Description
Failed
Preparations
for CS
Incoming
Inter-RAT
Handover
(Relocation
failure in
target
CN/RNC or
target
system)

67189 VS.IRATHO.FailRelocPrepInCS.TRNCS Number of


761
ysRelocUnsupp
Failed
Preparations
for CS
Incoming
Inter-RAT
Handover
(Relocation
not
supported in
target RNC
or target
system)

NE
910

Count
er ID

Counter Name

Counter
Description
available)

NE

Featu
re ID

Feature
Name

WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 IRATHO.SuccOutPSUE
763

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RAT
802
Handovers
Initiated by
UE for Cell

PS
Handover
Between
UMTS and
GPRS

67189 VS.IRATHO.FailOutCS.UEFail.GCell
907

Number of
BSC6 WRF
Failed CS
910
DInter-RAT
02030
HandoversBe
3
tween
WRF
Neighboring
DCells Due to
02030
UE Fault
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67189 VS.IRATHO.FaiOutPSUTRAN.UEFail.G Number of


908
Cell
Failed PS
Inter-RAT
Handovers
Between
Neighboring
Cells Due to
UE Fault

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67189 VS.HHO.FailOut.NoReply.NCell
912

Number of
Failed Hard
Handover
Between
Neighboring
Cells Due to
Timeout

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.IRATHO.AttRelocPrepInCS.RNC
311

Number of
BSC6 WRF
CS Incoming 910
DInter-RAT
02030
Handover
3
Preparation
WRF
Attempts for
DRNC
02030
5
WRF
D02030

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID
6

Feature
Name
Load

67190 VS.IRATHO.SuccRelocPrepInCS.RNC
312

Number of
BSC6 WRF
Successful
910
DPreparations
02030
for CS
3
Incoming
WRF
Inter-RAT
DHandover for
02030
RNC
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccInCS.RNC
314

Number of
BSC6 WRF
Successful
910
DCS Incoming
02030
Inter-RAT
3
Handovers
WRF
for RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.AttOutPSUE.RNC
316

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts
WRF
Initiated by
DUE for RNC
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67190 VS.IRATHO.AttRelocPrepOutCS.RNC
398

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02030
Handover
3
Preparation
WRF
Attempts for
DRNC
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccOutCS.RNC
399

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Inter-RAT
3
Handovers
WRF
for RNC
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.SuccRelocPrepOutCS.RNC
400

Number of
BSC6 WRF
Successful
910
DPreparations
02030
for CS
3
Outgoing
WRF
Inter-RAT
DHandover for
02030
RNC
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.FailInCS.NoReply
410

Number of
Failed CS

Inter
System

BSC6 WRF
910
D-

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 IRATHO.AttOutPSUTRAN
411

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts
WRF
Initiated by
DRNC for Cell
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 IRATHO.SuccOutPSUTRAN
412

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF
Initiated by
DRNC for Cell
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Inter-RAT
Incoming
Handovers
Due to No
Response
from UE for
Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67190 VS.IRATHO.AttOutPSUE
413

Number of
BSC6 WRF
PS Inter-RAT 910
DOutgoing
02030
Inter-RAT
802
Handover
Requests
Initiated by
UE for Cell

PS
Handover
Between
UMTS and
GPRS

67190 VS.IRATHO.SuccRelocPrepInCS
414

Number of
Successful
preparations
for CS
Incoming
Inter-RAT
Handovers
for Cell

BSC6 WRF
910
D02040
002
WRF
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.LCC.LDR.InterRATCS
440

Number of
BSC6 WRF
UEs
910
DPerforming
02030
CS Inter6
RAT
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67190 VS.LCC.LDR.InterRATPS
441

Number of
BSC6 WRF
UEs
910
DPerforming
02030
PS Inter-RAT
6
Handovers in
Basic

Inter-RAT
Handover
Based on
Load

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67190 IRATHO.FailOutPSUTRAN.CfgUnsupp
476

Number of
BSC6 WRF
Failed PS
910
DOutgoing
02030
Inter-RAT
3
Handovers
WRF
Initiated by
DRNC
02030
(Configuratio
5
n
WRF
unsupported)
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 IRATHO.FailOutPSUTRAN.PhyChFail
477

Number of
Failed PS
Outgoing
Inter-RAT
Handovers
Initiated by
RNC
(Physical
Channel
Failure)

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67190 VS.IRATHO.AttRelocPrepOutCS.Service Number of


BSC6 WRF
593
Preparation 910
DAttempts for
02030
CS Outgoing
5
Inter-RAT
Handover
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

Congestion
for Cell

67190 VS.HSDPA.SHO.ServCellChg.AttOut
698

Number of
Intra-RNC
HSDPA

BSC6 WRF HSDPA


910
DMobility
01061 Manageme

Count
er ID

Counter Name

Counter
Description
Serving Cell
Change
Attempts for
Cell

NE

Featu
re ID
006

Feature
Name
nt

67190 VS.HSDPA.SHO.ServCellChg.SuccOut
699

Number of
BSC6 WRF
Intra-RNC
910
DHSDPA
01061
Serving Cell
006
Change
Success in
RNC for Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.H2H.AttOutIntraFreq
700

Number of
BSC6 WRF
Intra910
DFrequency
01061
HSDPA Hard
006
Handover
Attempts
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.H2H.SuccOutIntraFreq Number of


BSC6 WRF
701
Successful
910
DIntra01061
Frequency
006
HSDPA Hard
Handovers
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.H2H.AttOutInterFreq
702

HSDPA
Mobility
Manageme
nt

Number of
BSC6 WRF
Inter910
DFrequency
01061
HSDPA Hard
006
Handover
Attempts
Without

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Channel
Change for
Cell
67190 VS.HSDPA.HHO.H2H.SuccOutInterFreq Number of
BSC6 WRF
703
Successful
910
DInter01061
Frequency
006
HSDPA Hard
Handovers
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.NoChR.Att.NCell
708

Number of
BSC6 WRF
HSDSCH-to- 910
DHSDSCH
01061
hard
006
Handover
Requests
Without
Channel
Change
Between
Neighboring
Cells

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.HHO.NoChR.Succ.NCell
709

Number of
BSC6 WRF
Successful
910
DHSDSCH-to01061
HSDSCH
006
hard
Handovers
Without
Channel
Change
Between
Neighboring
Cells

HSDPA
Mobility
Manageme
nt

67190 VS.HSDPA.ServCellChg.Att.NCell

Number of

HSDPA

BSC6 WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

710

HSDPA
Serving Cell
Change
Attempts
Between
Neighboring
Cells

910

DMobility
01061 Manageme
006
nt

67190 VS.HSDPA.ServCellChg.Succ.NCell
711

Number of
Successful
HSDPA
Serving Cell
Changes
Between
Neighboring
Cells

BSC6 WRF
910
D01061
006

HSDPA
Mobility
Manageme
nt

67190 VS.IRATHO.SuccRelocPrepOutCS.Servi Number of


BSC6 WRF
856
ce
Successful
910
DPreparations
02030
for CS
5
Outgoing
Inter-RAT
Handover
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.IRATHO.SuccOutCS.Service
857

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Inter-RAT
5
Handovers
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.IRATHO.AttOutPSUTRAN.Service
858

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
5
Attempts

Inter-RAT
Handover
Based on
Service

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67190 VS.IRATHO.SuccOutPSUTRAN.Service Number of


BSC6 WRF
859
Successful
910
DPS Outgoing
02030
Inter-RAT
5
Handovers
Initiated by
the RNC
Based on
Service Type
for Cell

Inter-RAT
Handover
Based on
Service

67190 VS.HHO.AttInterFreqOut.IntraNodeB
877

Number of
Outgoing
InterFrequency
Hard
Handover
Attempts in
NodeB for
Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.SuccInterFreqOut.IntraNodeB
878

Number of
BSC6 WRF
Successful
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers in
02030
NodeB for
4
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Initiated by
the RNC
Based on
Service Type
for Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67190 VS.HHO.AttInterFreqOut.InterNodeBIntr Number of


BSC6 WRF
884
aRNC
Outgoing
910
DInter02030
Frequency
2
Hard
WRF
Handovers
DAttempts
02030
Between
4
Different
NodeBs of
RNC for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.SuccInterFreqOut.InterNodeBIn Number of


BSC6 WRF
885
traRNC
Successful
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between
4
Different
NodeBs of
RNC for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.AttInterFreqOut.InterRNC
891

Number of
Outgoing
InterFrequency
Hard
Handovers
Attempts
Between
RNCs for
Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67190 VS.HHO.SuccInterFreqOut.InterRNC
892

Number of
Successful
Outgoing

BSC6 WRF Inter


910
DFrequency
02030 Hard

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

2
WRF
D02030
4

Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67191 VS.LCC.LDR.HSDPA.InterRATPS
152

Number of
BSC6 WRF
HSDPA UEs 910
DPerforming
02030
PS Inter-RAT
6
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67191 VS.IRATHO.HSDPA.AttOutPSUTRAN
155

Number of
BSC6 WRF
PS Inter-RAT 910
DOutgoing
01061
Handover
006
Attempts for
HSDPA
Services for
Cell

HSDPA
Mobility
Manageme
nt

67191 VS.IRATHO.HSDPA.SuccOutPSUTRAN Number of


BSC6 WRF
156
Successful
910
DPS Outgoing
01061
Inter-RAT
006
Handovers
for HSDPA
Services for
Cell

HSDPA
Mobility
Manageme
nt

67191 VS.HSDPA.HHO.H2D.AttOutIntraFreq
157

HSDPA
Mobility
Manageme
nt

InterFrequency
Hard
Handovers
Between
RNCs for
Cell

Number of
IntraFrequency
H2D Hard
Handover

NE

BSC6 WRF
910
D01061
006

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Attempts for
Cell
67191 VS.HSDPA.HHO.H2D.SuccOutIntraFreq Number of
158
Successful
IntraFrequency
H2D Hard
Handovers
for Cell
67191 VS.HSDPA.HHO.H2D.AttOutInterFreq
159

BSC6 WRF
910
D01061
006

HSDPA
Mobility
Manageme
nt

Number of
BSC6 WRF
Inter910
DFrequency
01061
H2D Hard
006
Handover
Attempts for
Cell

HSDPA
Mobility
Manageme
nt

67191 VS.HSDPA.HHO.H2D.SuccOutInterFreq Number of


160
Successful
InterFrequency
H2D Hard
Handovers
for Cell

BSC6 WRF
910
D01061
006

HSDPA
Mobility
Manageme
nt

67191 VS.HHO.AttBlindHO
694

Number of
BSC6 WRF
Outgoing
910
DEmergency
02030
Blind
2
Handover
Attempts for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage

67191 VS.HHO.SuccBlindHO
695

Number of
Successful
Outgoing
Emergency
Blind Hard
Handovers
for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage

BSC6 WRF
910
D02030
2

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67192 IRATHO.FailRelocPrepOutCS.HigherTra Number of


BSC6 WRF
186
fficLod
Failed
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell (Traffic
3
Load In The
WRF
Target Cell
DHigher Than
02030
In The
5
Source Cell)
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.FailRelocPrepInCS.TgtHigh Number of


BSC6 WRF
187
Load
Failed
910
DPreparations
02040
for CS
002
Incoming
WRF
Inter-RAT
DHandover
02030
(Traffic Load
3
In The Target
WRF
Cell Higher
DThan In The
02030
Source Cell)
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.HSUPA.SHO.AttOut
367

HSUPA
Mobility
Manageme
nt

Number of
BSC6 WRF
EDCH RL
910
DAddition and
01061
Deletion
204
Attempts by
Soft
Handover for

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Cell
67192 VS.HSUPA.SHO.SuccOut
368

Number of
BSC6 WRF
Successful
910
DEDCH RL
01061
Additions
204
and
Deletions by
Soft
Handover for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.SHO.ServCellChg.SuccOut
369

Number of
Successful
HSUPA
Serving Cell
Changes in
Soft
Handover
Status for
Cell

BSC6 WRF
910
D01061
204

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.SHO.ServCellChg.AttOut
370

Number of
HSUPA
Serving Cell
Change
Attempts in
Soft
Handover
Status for
Cell

BSC6 WRF
910
D01061
204

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2E.SuccOutIntraFreq
371

Number of
BSC6 WRF
Successful
910
DHSUPA
01061
Serving Cell
204
Changes Due
to IntraFrequency
Hard
Handover
without

HSUPA
Mobility
Manageme
nt

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Channel
Change for
Cell
67192 VS.HSUPA.HHO.E2E.AttOutIntraFreq
372

Number of
BSC6 WRF
HSUPA
910
DServing Cell
01061
Change
204
Attempts
Due to IntraFrequency
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2E.SuccOutInterFreq
373

Number of
BSC6 WRF
Successful
910
DHSUPA
01061
Serving Cell
204
Changes Due
to InterFrequency
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2E.AttOutInterFreq
374

Number of
BSC6 WRF
HSUPA
910
DServing Cell
01061
Change
204
Attempts
Due to InterFrequency
Hard
Handover
without

HSUPA
Mobility
Manageme
nt

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Channel
Change for
Cell
67192 VS.HSUPA.HHO.E2D.SuccOutIntraFreq Number of
472
Successful
HSUPA
IntraFrequency
Hard
Handovers
for
Cell(EDCH
to DCH)
67192 VS.HSUPA.HHO.E2D.AttOutIntraFreq
473

BSC6 WRF
910
D01061
204

HSUPA
Mobility
Manageme
nt

Number of
BSC6 WRF
HSUPA
910
DIntra01061
Frequency
204
Hard
Handover
Attempts for
Cell(EDCH
to DCH)

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2D.SuccOutInterFreq Number of


474
Successful
HSUPA
InterFrequency
Hard
Handovers
for
Cell(EDCH
to DCH)

BSC6 WRF
910
D01061
204

HSUPA
Mobility
Manageme
nt

67192 VS.HSUPA.HHO.E2D.AttOutInterFreq
475

BSC6 WRF
910
D01061
204

HSUPA
Mobility
Manageme
nt

Number of
HSUPA
InterFrequency
Hard
Handover

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Attempts for
Cell(EDCH
to DCH)
67192 VS.IRATHO.HSUPA.SuccOutPSUTRAN Number of
BSC6 WRF
506
Successful
910
DPS Outgoing
01061
Inter-RAT
204
Handovers
for HSUPA
Services for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.IRATHO.HSUPA.AttOutPSUTRAN
507

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
01061
Handover
204
Attempts for
HSUPA
Services for
Cell

HSUPA
Mobility
Manageme
nt

67192 VS.HHO.FailInterFreqOut.PrepFail
555

Number of
BSC6 WRF
Failed
910
DPreparations
02030
for Outgoing
2
InterWRF
Frequency
DHard
02030
Handovers
4
for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67192 VS.HHO.FailInterFreqOut.RLSetupFail
557

Number of
BSC6 WRF
Failed
910
DPreparations
02030
for Outgoing
2
InterWRF
Frequency
DHard
02030

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter

Count
er ID

Counter Name

Counter
Description
Handovers
Due to Radio
Link
Establishmen
t Failure for
Cell

NE

Featu
re ID
4

Feature
Name
Frequency
Hard
Handover
Based on
DL QoS

67192 VS.LCC.LDR.HSUPA.InterRATPS
645

Number of
BSC6 WRF
HSUPA UEs 910
DPerforming
02030
PS Inter-RAT
6
Handover in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.AttRelocPrepOutCS.Sig
654

Number of
Preparations
for CS
Outgoing
Inter-RAT
Handover
When only
Signaling
Exists for
Cell

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.SuccRelocPrepOutCS.Sig
655

Number of
Successful
Preparations
for CS
Outgoing
Inter-RAT
Handover
When only
Signaling
Exists for
Cell

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67192 VS.IRATHO.AttOutCS.Sig
656

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts
WRF
When only
DSignaling
02030
Exists for
5
Cell
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.SuccOutCS.Sig
657

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Inter-RAT
3
Handovers
WRF
When only
DSignaling
02030
Exists for
5
Cell
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 IRATHO.FailRelocPrepOutCS.NoResAva Number of


BSC6 WRF
658
il
Failed
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell (No
3
Resource
WRF
Available)
D02030
5
WRF
D02030

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID
6

Feature
Name
Load

67192 IRATHO.FailRelocPrepOutCS.UKnowR
659
NC

Number of
BSC6 WRF
Failed
910
DPreparations
02040
for CS
002
Outgoing
WRF
Inter-RAT
DHandover for
02030
Cell
3
(Unknown
WRF
Target RNC)
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.FailOutCS.NoReply
660

Number of
BSC6 WRF
Times that
910
Dthe Timer
02040
Waiting for
002
Iu Release
WRF
Command
DExpires in
02030
CS Outgoing
3
Inter-RAT
WRF
Handover for
DCell
02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.FailOutPSUTRAN.NoReply Number of


661
Times that
the Timer
Waiting for
Iu Release

BSC6 WRF
910
D02030
3
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT

Count
er ID

Counter Name

Counter
Description
Command
Expires in PS
Outgoing
Inter-RAT
Handover
Initiated by
RNC for Cell

NE

Featu
re ID

Feature
Name

D02030
5
WRF
D02030
6

Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

67192 VS.IRATHO.AttRelocPrepOutPS
662

Number of
BSC6 WRF
Preparations 910
Dfor Enhanced
02030
PS Outgoing
802
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocPrepOutPS
663

Number of
BSC6 WRF
Successful
910
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.AttRelocOutPS
664

Number of
BSC6 WRF
Enhanced PS 910
DOutgoing
02030
Inter-RAT
802
Handover
Attempts for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocOutPS
665

Number of
BSC6 WRF
Successful
910
DEnhanced PS
02030
Outgoing
802
Inter-RAT
Handovers
for Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.TAlEx Number of

BSC6 WRF

PS

Count
er ID
666

Counter Name
p

Counter
Description

NE

Failed
910
Preparations
for Enhanced
PS Outgoing
Inter-RAT
Handover for
Cell
(TRELOCall
oc expiry)

Featu
re ID

Feature
Name

DHandover
02030 Between
802
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.TgtFai Number of


BSC6 WRF
667
l
Failed
910
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell
(Relocation
Failure in
Target
CN/RNC or
Target
System)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.ReloU Number of


BSC6 WRF
668
nSupp
Failed
910
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell
(Relocation
not
supported in
Target RNC
or Target
system)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.TgtHig Number of


669
hLoad
Failed

PS
Handover

BSC6 WRF
910
D-

Count
er ID

Counter Name

Counter
Description
Preparations
for Enhanced
PS Outgoing
Inter-RAT
Handover for
Cell (Traffic
Load In The
Target Cell
Higher Than
In The
Source Cell)

NE

Featu
re ID

Feature
Name

02030 Between
802
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.NoRes Number of


BSC6 WRF
670
Avail
Failed
910
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell (No
Resource
Available)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepOutPS.UnKn
671
owRNC

Number of
BSC6 WRF
Failed
910
DPreparations
02030
for Enhanced
802
PS Outgoing
Inter-RAT
Handover for
Cell
(Unknown
Target RNC)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocOutPS.CfgUnSup
672
p

Number of
BSC6 WRF
Failed
910
DEnhanced PS
02030
Outgoing
802
Inter-RAT
Handovers
for Cell
(Configuratio

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

n
Unsupported
)
67192 VS.IRATHO.FailRelocOutPS.PhyChFail
673

Number of
BSC6 WRF
Failed
910
DEnhanced PS
02030
Outgoing
802
Inter-RAT
Handovers
for Cell
(Physical
Channel
Failure)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocOutPS.NoReply
674

Number of
BSC6 WRF
Times that
910
Dthe Timer
02030
Waiting for
802
Iu Release
Command
Expires in
Enhanced PS
Outgoing
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.AttRelocPrepInPS
675

Number of
BSC6 WRF
Preparations 910
Dfor Enhanced
02030
PS Incoming
802
Inter-RAT
Handover for
Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.SuccRelocPrepInPS
676

Number of
BSC6 WRF
Successful
910
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Handover for
Cell
67192 VS.IRATHO.SuccRelocInPS
677

Number of
BSC6 WRF
Successful
910
DEnhanced PS
02030
Incoming
802
Inter-RAT
Handovers
for Cell

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.TgtFail
678

Number of
BSC6 WRF
Failed
910
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
cell
(Relocation
failure in
target
CN/RNC or
target
system)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.ReloUn
679
Supp

Number of
BSC6 WRF
Failed
910
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
cell
(Relocation
not
supported in
target RNC
or target
system)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.ResUna

Number of

PS

BSC6 WRF

Count
er ID
680

Counter Name
vail

Counter
Description

NE

Failed
910
Preparations
for Enhanced
PS Incoming
Inter-RAT
Handover for
cell (No
resource
available)

Featu
re ID

Feature
Name

DHandover
02030 Between
802
UMTS and
GPRS

67192 VS.IRATHO.FailRelocPrepInPS.TgtHigh Number of


BSC6 WRF
681
Load
Failed
910
DPreparations
02030
for Enhanced
802
PS Incoming
Inter-RAT
Handover for
cell (Traffic
Load In The
Target Cell
Higher Than
In The
Source Cell)

PS
Handover
Between
UMTS and
GPRS

67192 VS.IRATHO.FailRelocInPS.NoReply
682

PS
Handover
Between
UMTS and
GPRS

Number of
BSC6 WRF
Failed
910
DEnhanced PS
02030
Incoming
802
Inter-RAT
Handovers
Due to UE
Response
Timeout for
Cell

67193 VS.HHO.InterFreqOut.CS.MeasTimeOut Number of


397
Handovers
Not
Performed
Due to CS
InterFrequency

BSC6 WRF
910
D02030
2
WRF
D02030

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter

Count
er ID

Counter Name

Counter
Description
Measurement
Expiry for
Cell

NE

Featu
re ID
4

Feature
Name
Frequency
Hard
Handover
Based on
DL QoS

67193 VS.HHO.InterFreqOut.PS.MeasTimeOut
398

Number of
BSC6 WRF
Handovers
910
DNot
02030
Performed
2
Due to PS
WRF
InterDFrequency
02030
Measurement
4
Expiry for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67193 VS.IRATHO.OutCS.MeasTimeOut
399

Number of
BSC6 WRF
CS Inter910
DRAT
02030
Measurement
3
Expiry for
WRF
Cell
D02030
9

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
DL QoS

67193 VS.IRATHO.OutPS.MeasTimeOut
400

Number of
BSC6 WRF
PS Inter-RAT 910
DMeasurement
02030
Expiry for
3
Cell
WRF
D02030
9

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
DL QoS

67193 VS.HHO.AttInterFreqOut.CS.TrigRscp
401

Number of
CS InterFrequency
Hard
Handover

Inter
Frequency
Hard
Handover
Based on

BSC6 WRF
910
D02030
2

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Attempts
Based on
RSCP for
Cell

Feature
Name
Coverage

67193 VS.HHO.AttInterFreqOut.CS.TrigEcNo
402

Number of
CS InterFrequency
Hard
Handover
Attempts
Based on
EcNo for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

67193 VS.HHO.AttInterFreqOut.PS.TrigRscp
403

Number of
PS InterFrequency
Hard
Handover
Attempts
Based on
RSCP for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

67193 VS.HHO.AttInterFreqOut.PS.TrigEcNo
404

Number of
PS InterFrequency
Hard
Handover
Attempts
Based on
EcNo for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

67193 VS.IRATHO.AttOutCS.TrigRscp
405

Number of
CS InterRAT
Handover
Attempts
Based on
RSCP for

BSC6 WRF
910
D02030
3

Inter-RAT
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Cell
67193 VS.IRATHO.AttOutCS.TrigEcNo
406

Number of
CS InterRAT
Handover
Attempts
Based on
EcNo for
Cell

BSC6 WRF
910
D02030
3

Inter-RAT
Handover
Based on
Coverage

67193 VS.IRATHO.AttOutPS.TrigRscp
407

Number of
BSC6 WRF
PS Inter-RAT 910
DHandover
02030
Attempts
3
Based on
RSCP for
Cell

Inter-RAT
Handover
Based on
Coverage

67193 VS.IRATHO.AttOutPS.TrigEcNo
408

Number of
BSC6 WRF
PS Inter-RAT 910
DHandover
02030
Attempts
3
Based on
EcNo for
Cell

Inter-RAT
Handover
Based on
Coverage

67194 VS.CM.ULSF2.Act.Att
881

Number of
BSC6 WRF
Uplink SF-2 910
DCompression
02030
Mode
2
Activation
WRF
Requests for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.ULHLS.Act.Att
882

Number of
Uplink HLS

Inter
Frequency

BSC6 WRF
910
D-

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02030
2
WRF
D02030
4

Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.ULSF2.Act.Fail
883

Number of
BSC6 WRF
Uplink SF-2 910
DCompression
02030
Mode
2
Activation
WRF
Failures for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.ULHLS.Act.Fail
884

Number of
BSC6 WRF
Uplink HLS 910
DCompression
02030
Mode
2
Activation
WRF
Failures for
DCell
02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLSF2.Act.Att
885

Number of
BSC6 WRF
Downlink
910
DSF-2
02030
Compression
2
Mode
WRF

Inter
Frequency
Hard
Handover
Based on

Compression
Mode
Activation
Requests for
Cell

NE

Count
er ID

Counter Name

Counter
Description
Activation
Requests for
Cell

NE

Featu
re ID

Feature
Name

DCoverage
02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLHLS.Act.Att
886

Number of
BSC6 WRF
Downlink
910
DHLS
02030
Compression
2
Mode
WRF
Activation
DRequests for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLSF2.Act.Fail
887

Number of
BSC6 WRF
Downlink
910
DSF-2
02030
Compression
2
Mode
WRF
Activation
DFailures for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

67194 VS.CM.DLHLS.Act.Fail
888

Number of
BSC6 WRF
Downlink
910
DHLS
02030
Compression
2
Mode
WRF
Activation
DFailures for
02030
Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Hard
Handover
Based on
DL QoS

67195 VS.HSDPA.SHO.ServCellChg.AttOutIur
481

Number of
BSC6 WRF
Inter-RNC
910
DHSDPA
01061
Serving Cell
006
Change
Attempts for
Cell

67195 VS.HSDPA.SHO.ServCellChg.SuccOutIu Number of


482
r
Inter-RNC
HSDPA
Serving Cell
Change
Success for
Cell

HSDPA
Mobility
Manageme
nt

BSC6 WRF
910
D01061
006

HSDPA
Mobility
Manageme
nt

67195 VS.HSDPA.HHO.H2H.AttOutIur
483

Number of
BSC6 WRF
Inter-RNC
910
DHSDPA Hard
01061
Handover
006
Attempts
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67195 VS.HSDPA.HHO.H2H.SuccOutIur
484

Number of
BSC6 WRF
Successful
910
DInter-RNC
01061
HSDPA Hard
006
Handovers
Without
Channel
Change for
Cell

HSDPA
Mobility
Manageme
nt

67195 VS.HSUPA.SHO.ServCellChg.AttOutIur

Number of

HSUPA

BSC6 WRF

Count
er ID

Counter Name

485

Counter
Description
inter-RNC
HSUPA
Serving Cell
Change
Attempts in
Soft
Handover
Status for
Cell

67195 VS.HSUPA.SHO.ServCellChg.SuccOutIu Number of


486
r
Successful
inter-RNC
HSUPA
Serving Cell
Changes in
Soft
Handover
Status for
Cell

NE
910

Featu
re ID

Feature
Name

DMobility
01061 Manageme
204
nt

BSC6 WRF
910
D01061
204

HSUPA
Mobility
Manageme
nt

67195 VS.HSUPA.HHO.E2E.SuccOutIur
487

Number of
BSC6 WRF
Successful
910
DHSUPA
01061
Serving Cell
204
Changes Due
to inter-RNC
Hard
Handover
without
Channel
Change for
Cell

HSUPA
Mobility
Manageme
nt

67195 VS.HSUPA.HHO.E2E.AttOutIur
488

Number of
BSC6 WRF
HSUPA
910
DServing Cell
01061
Change
204
Attempts
Due to interRNC Hard
Handover

HSUPA
Mobility
Manageme
nt

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

67196 VS.LCC.LDR.HSUPA.InterRATCS
029

Number of
BSC6 WRF
HSUPA UEs 910
DPerforming
02030
CS Inter6
RAT
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67196 VS.LCC.LDR.HSDPA.InterRATCS
030

Number of
BSC6 WRF
HSDPA UEs 910
DPerforming
02030
CS Inter6
RAT
Handovers in
Basic
Congestion
for Cell

Inter-RAT
Handover
Based on
Load

67203 VS.RAB.ModReqCS.VP.Fallback.RNC
800

Number of
VP Services
Fallen Back
to AMR
Services for
RNC

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load
HCS
(Hierarchic
al Cell
Structure)

without
Channel
Change for
Cell

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6
WRF
D02120
0

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.HHO.FailInterFreqOut.InterRNC.Cfg Number of


BSC6 WRF
853
Unsupp
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between the
4
RNCs for
Cell
(Configuratio
n
Unsupported
)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailInterFreqOut.InterRNC.Phy Number of


854
ChFail
Failed
Outgoing
InterFrequency
Hard
Handovers
Between the
RNCs for
Cell
(Physical
Channel
Failure)

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailInterFreqOut.InterRNC.ISR Number of


BSC6 WRF
855
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between the
4
RNCs for
Cell
(Incompatibl
e
Simultaneous

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between the
4
RNCs for
Cell (Invalid
Configuratio
n)

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Reconfigurat
ion)
73393 VS.HHO.FailInterFreqOut.InterRNC.Inv
856
Cfg

73393 VS.HHO.FailInterFreqOut.InterRNC.Cell Number of


857
Updt
Failed
Outgoing
InterFrequency
Hard
Handovers
Between the
RNCs for
Cell (Cell
Update
Occurred)
73393 VS.HHO.FailInterFreqOut.InterRNC.No
858
Reply

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
Between the
4
RNCs Due to
No Response
from the UE
for Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.IRATHO.AttOutCS.TrigDLTxp
923

Number of
BSC6 WRF
CS Inter910
DRAT
02030
Handover
9
Attempts
Based on DL
Code Power
for Cell

Inter-RAT
Handover
Based on
DL QoS

73393 VS.IRATHO.AttOutPS.TrigDLTxp
925

Number of
BSC6 WRF
PS Inter-RAT 910
DHandover
02030
Attempts
9
Based on DL
Code Power
for Cell

Inter-RAT
Handover
Based on
DL QoS

73393 VS.IRATHO.SuccOutCS.TrigRscp
926

Number of
Successful
CS InterRAT
Handovers
Based on
RSCP for
Cell

BSC6 WRF
910
D02030
3

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutCS.TrigEcNo
927

Number of
Successful
CS InterRAT
Handovers
Based on
EcNo for
Cell

BSC6 WRF
910
D02030
3

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutCS.TrigDLTxp
929

Number of
BSC6 WRF
Successful
910
DCS Inter02030
RAT
9
Handovers
Based on DL
Code Power

Inter-RAT
Handover
Based on
DL QoS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73393 VS.IRATHO.SuccOutPS.TrigRscp
930

Number of
BSC6 WRF
Successful
910
DPS Inter-RAT
02030
Handovers
3
Based on
RSCP for
Cell

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutPS.TrigEcNo
931

Number of
BSC6 WRF
Successful
910
DPS Inter-RAT
02030
Handovers
3
Based on
EcNo for
Cell

Inter-RAT
Handover
Based on
Coverage

73393 VS.IRATHO.SuccOutPS.TrigDLTxp
933

Number of
BSC6 WRF
Successful
910
DPS Inter-RAT
02030
Handovers
9
Based on DL
Code Power
for Cell

Inter-RAT
Handover
Based on
DL QoS

73393 VS.HHO.AttInterFreqOut.CS.Tcp
937

Number of
BSC6 WRF
CS Inter910
DFrequency
02030
Hard
4
Handover
Attempts
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.AttInterFreqOut.PS.Tcp
938

Number of
PS InterFrequency
Hard
Handover

Inter
Frequency
Hard
Handover
Based on

for Cell

BSC6 WRF
910
D02030
4

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Attempts
Based on DL
Transmit
Power for
Cell

DL QoS

73393 VS.HHO.SuccInterFreqOut.CS.Tcp
948

Number of
BSC6 WRF
Successful
910
DCS Inter02030
Frequency
4
Hard
Handovers
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.SuccInterFreqOut.PS.Tcp
949

Number of
BSC6 WRF
Successful
910
DPS Inter02030
Frequency
4
Hard
Handovers
Based on DL
Transmit
Power for
Cell

Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HSUPA.TTI2to10.Att
984

Number of
BSC6 WRF
TTI Switch 910
DAttempts
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(2ms to
01061
10ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HSUPA.TTI2to10.Succ
985

Number of
BSC6 WRF
Successful
910
DTTI Switches
01069
During RB
0

TTI Switch
for BE
Services
Based on

Count
er ID

Counter Name

Counter
Description
Reconfigurat
ion for
Cell(2ms to
10ms)

NE

Featu
re ID

Feature
Name

WRF
D01061
404

Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HSUPA.TTI10to2.Att
986

Number of
BSC6 WRF
TTI Switch 910
DAttempts
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(10ms to
01061
2ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HSUPA.TTI10to2.Succ
987

Number of
BSC6 WRF
Successful
910
DTTI Switches
01069
During RB
0
Reconfigurat
WRF
ion for
DCell(10ms to
01061
2ms)
404

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73393 VS.HHO.AttOutIntraNodeB.CS.NCell
988

Number of
BSC6 WRF
CS Outgoing 910
DIntra-NodeB
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
DL QoS

73393 VS.HHO.SuccOutIntraNodeB.CS.NCell
989

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Intra-NodeB
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.NoReply.C
990
S.NCell

Number of
Failed CS
Outgoing
Intra-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.PhyChFail.
991
CS.NCell

Number of
Failed CS
Outgoing
Intra-NodeB
Inter-Cell
Hard

BSC6 WRF
910
D02030
1
WRF
D-

Intra
Frequency
Hard
Handover
Inter
Frequency

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

02030
2
WRF
D02030
4

Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.AttOutIntraNodeB.PS.NCell
992

Number of
BSC6 WRF
PS Outgoing 910
DIntra-NodeB
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.SuccOutIntraNodeB.PS.NCell
993

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Intra-NodeB
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover

Handovers
(Physical
Channel
Failure)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.NoReply.PS Number of


994
.NCell
Failed PS
Outgoing
Intra-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.FailOutIntraNodeB.PhyChFail.
995
PS.NCell

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73393 VS.HHO.AttOutInterNodeBIntraRNC.CS Number of


BSC6 WRF
996
.NCell
CS Outgoing 910
DIntra-RNC
02030
Inter-NodeB
1
Inter-Cell
WRF

Intra
Frequency
Hard
Handover
Inter

Number of
Failed PS
Outgoing
Intra-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

D02030
2
WRF
D02030
4

Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Intra-RNC
1
Inter-NodeB
WRF
Inter-Cell
DHard
02030
Handovers
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Hard
Handover
Attempts

73393 VS.HHO.SuccOutInterNodeBIntraRNC.
997
CS.NCell

73393 VS.HHO.FailOutInterNodeBIntraRNC.N Number of


998
oReply.CS.NCell
Failed CS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

NE

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Handover
Based on
DL QoS

73393 VS.HHO.FailOutInterNodeBIntraRNC.P
999
hyChFail.CS.NCell

Number of
Failed CS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.AttOutInterNodeBIntraRNC.PS Number of


BSC6 WRF
000
.NCell
PS Outgoing 910
DIntra-RNC
02030
Inter-NodeB
1
Inter-Cell
WRF
Hard
DHandover
02030
Attempts
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.SuccOutInterNodeBIntraRNC.P Number of


BSC6 WRF
001
S.NCell
Successful
910
DPS Outgoing
02030
Intra-RNC
1

Intra
Frequency
Hard
Handover

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

Inter-NodeB
Inter-Cell
Hard
Handovers

WRF
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterNodeBIntraRNC.N Number of


002
oReply.PS.NCell
Failed PS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(UE No
Response)

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterNodeBIntraRNC.P
003
hyChFail.PS.NCell

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency

Number of
Failed PS
Outgoing
Intra-RNC
Inter-NodeB
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Hard
Handover
Based on
DL QoS

73394 VS.HHO.AttOutInterRNCIur.CS.NCell
004

Number of
BSC6 WRF
CS Outgoing 910
DInter-RNC
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.SuccOutInterRNCIur.CS.NCell
005

Number of
BSC6 WRF
Successful
910
DCS Outgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterRNCIur.CfgUnsup. Number of


006
CS.NCell
Failed CS
Outgoing

BSC6 WRF Intra


910
DFrequency
02030 Hard

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

1
WRF
D02030
2
WRF
D02030
4

Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

BSC6 WRF
910
D02030
1
WRF
D02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Number of
BSC6 WRF
PS Outgoing 910
DInter-RNC
02030
Inter-Cell
1
Hard
WRF
Handover
DAttempts
02030
2
WRF
D-

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage

Inter-RNC
Inter-Cell
Hard
Handovers
(Configuratio
n
Unsupported
)

73394 VS.HHO.FailOutInterRNCIur.PhyChFail. Number of


007
CS.NCell
Failed CS
Outgoing
Inter-RNC
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

73394 VS.HHO.AttOutInterRNCIur.PS.NCell
008

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Inter
4
Frequency
Hard
Handover
Based on
DL QoS
73394 VS.HHO.SuccOutInterRNCIur.PS.NCell
009

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
2
WRF
D02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterRNCIur.CfgUnsup. Number of


BSC6 WRF
010
PS.NCell
Failed PS
910
DOutgoing
02030
Inter-RNC
1
Inter-Cell
WRF
Hard
DHandovers
02030
(Configuratio
2
n
WRF
Unsupported
D)
02030
4

Intra
Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73394 VS.HHO.FailOutInterRNCIur.PhyChFail. Number of

Intra

BSC6 WRF

Count
er ID
011

Counter Name
PS.NCell

73394 VS.IRATHO.AttInCS
014

Counter
Description

Featu
re ID

Feature
Name

D02030
1
WRF
D02030
2
WRF
D02030
4

Frequency
Hard
Handover
Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

Number of
BSC6 WRF
CS Incoming 910
DInter-RAT
02040
Handover
002
Attempts for
WRF
Cell
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Failed PS
Outgoing
Inter-RNC
Inter-Cell
Hard
Handovers
(Physical
Channel
Failure)

73394 VS.IRATHO.FailRelocPrepOutCS.Cancel Number of


015
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
for Cell
(Relocation
Cancelled)

NE
910

BSC6 WRF
910
D02030
3
WRF
D02030
5

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

WRF
D02030
6

Inter-RAT
Handover
Based on
Load

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepInCS.Abort
017

Number of
BSC6 WRF
CS Incoming 910
DInter-RAT
02030
Handover
3
Preparation
WRF
Failures for
DCell (Iu
02030
RELEASE
5
COMMAND
WRF
Received)
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailOutCS.Abort
018

Number of
BSC6 WRF
Abnormally 910
DTerminated
02030
CS Outgoing
3
Inter-RAT
WRF
Handovers
Dfor Cell
02030
5
WRF
D-

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover

73394 VS.IRATHO.FailRelocPrepOutCS.CNNo Number of


016
Reply
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
for Cell
(Relocation
Command
Wait
Timeout)

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

02030 Based on
6
Load
73394 VS.IRATHO.FailRelocPrepOutCS.Abort
019

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02030
Handover
3
Preparation
WRF
Failures for
DCell (Iu
02030
RELEASE
5
COMMAND
WRF
Received)
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.ReqInf Number of


020
oNotAvail
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
for Cell
(Requested
Information
Not
Available)

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailOutPS
021

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

Number of
Failed PS
Outgoing
Inter-RAT
Handovers
Initiated by
the RNC for
Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73394 VS.IRATHO.FailOutPS.Abort
022

Number of
BSC6 WRF
Abnormally 910
DTerminated
02030
PS Outgoing
3
Inter-RAT
WRF
Handovers
Dfor Cell
02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.AttRelocPrepOutCS.GCell
034

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02030
Handover
3
Preparation
WRF
Attempts
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.AttRelocPrepOutCS.DR.GC Number of


BSC6 WRF
035
ell
CS Outgoing 910
DInter-RAT
02040
Handover
002
Preparation
WRF
Attempts
D(Directed
02030
retry)
3
WRF
D02030
5
WRF
D02030

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID
6

73394 VS.IRATHO.AttRelocPrepOutCS.RF.GC Number of


036
ell
Failed CS
Outgoing
Inter-RAT
Handover
Preparations
(Relocation
desirable for
radio
reasons)

Feature
Name
Load

BSC6 WRF
910
D02030
3

Inter-RAT
Handover
Based on
Coverage

73394 VS.IRATHO.SuccRelocPrepOutCS.GCell Number of


BSC6 WRF
037
Successful
910
DCS Outgoing
02030
Inter-RAT
3
Handover
WRF
Preparations
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.TAlEx Number of


BSC6 WRF
038
p.GCell
Failed CS
910
DOutgoing
02030
Inter-RAT
3
Handover
WRF
Preparations
D(TRELOCall
02030
oc expiry)
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73394 VS.IRATHO.FailRelocPrepOutCS.TgtFai Number of


039
l.GCell
Failed CS
Outgoing

BSC6 WRF Inter-RAT


910
DHandover
02030 Based on

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73403 VS.HSDPA.HHO.H2D.AttOutIur
764

number of
BSC6 WRF
Inter-RNC
910
DH2D Hard
01061
Handover
006
Attempts for
Cell

HSDPA
Mobility
Manageme
nt

73403 VS.HSDPA.HHO.H2D.SuccOutIur
765

Number of
Successful
Inter-RNC
H2D Hard
Handovers
for Cell

BSC6 WRF
910
D01061
006

HSDPA
Mobility
Manageme
nt

73403 VS.HSUPA.HHO.E2D.AttOutIur
766

Number of
BSC6 WRF
inter-RNC
910
DHSUPA Hard
01061
Handover
204
Attempts for
Cell(EDCH
to DCH)

HSUPA
Mobility
Manageme
nt

73403 VS.HSUPA.HHO.E2D.SuccOutIur
767

Number of
BSC6 WRF
Successful
910
Dinter-RNC
01061
HSUPA Hard
204
Handovers
for
Cell(EDCH
to DCH)

HSUPA
Mobility
Manageme
nt

73403 VS.HHO.AttInterFreqIn.CS

Number of

Inter

Inter-RAT
Handover
Preparations
(Relocation
Failure in
Target
CN/RNC or
Target
System)

NE

BSC6 WRF

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

768

Requests for 910


CS Incoming
InterFrequency
Hard
Handovers
for Cell

D02030
2
WRF
D02030
4

Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.AttInterFreqIn.PS
769

Number of
BSC6 WRF
Requests for 910
DPS Incoming
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.AttInterFreqOut.CS
770

Number of
BSC6 WRF
Requests for 910
DCS Outgoing
02030
Inter2
Frequency
WRF
Hard
DHandovers
02030
for Cell
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.AttInterFreqOut.PS
771

Number of
BSC6 WRF
Requests for 910
DPS Outgoing
02030
Inter2

Inter
Frequency
Hard
Handover

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Frequency
Hard
Handovers
for Cell

WRF
D02030
4

Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqIn.CS
772

Number of
Successful
for CS
Incoming
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqIn.PS
773

Number of
Successful
for PS
Incoming
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqOut.CS
774

Number of
Successful
for CS
Outgoing
InterFrequency
Hard

BSC6 WRF
910
D02030
2
WRF
D02030

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter

Count
er ID

Counter Name

Counter
Description
Handovers
for Cell

NE

Featu
re ID
4

Feature
Name
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.SuccInterFreqOut.PS
775

Number of
Successful
for PS
Outgoing
InterFrequency
Hard
Handovers
for Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.InterFreqOut.CS.Drop
776

Number of
BSC6 WRF
CS Call
910
DDrops due to
02030
Unsuccessful
2
Outgoing
WRF
InterDFrequency
02030
Hard
4
Handovers
for cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73403 VS.HHO.InterFreqOut.PS.Drop
777

Number of
BSC6 WRF
PS Call
910
DDrops due to
02030
Unsuccessful
2
Outgoing
WRF
InterDFrequency
02030
Hard
4
Handovers
for cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
Based on
DL QoS

73404 VS.HHO.SuccInterFreqOut.CS.Rscp
081

Number of
Successful
CS InterFrequency
Hard
Handovers
Based on
RSCP for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

73404 VS.HHO.SuccInterFreqOut.CS.EcNo
082

Number of
Successful
CS InterFrequency
Hard
Handovers
Based on
EcNo for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

73404 VS.HHO.SuccInterFreqOut.PS.Rscp
083

Number of
Successful
PS InterFrequency
Hard
Handovers
Based on
RSCP for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

73404 VS.HHO.SuccInterFreqOut.PS.EcNo
084

Number of
Successful
PS InterFrequency
Hard
Handovers
Based on
EcNo for
Cell

BSC6 WRF
910
D02030
2

Inter
Frequency
Hard
Handover
Based on
Coverage

Count
er ID

Counter Name

73423 VS.IRATHO.FailOutPS.UEGen
107

Counter
Description

NE

Featu
re ID

Feature
Name

Number of
BSC6 WRF
Failed
910
DOutgoing
02030
UMTS-to3
GSM PS
WRF
Handovers
Ddue to UE
02030
Reselection
5
Back to a
WRF
UTRAN Cell
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73423 VS.SRVCC.U2GERAN.AttRelocPrepOut Number of


BSC6 WRF
288
PS
Outgoing
910
DInter-RAT PS
02030
Handover
802
Preparation
Attempts
Triggered by
SRVCC for
VoIP
Services for
Cell

PS
Handover
Between
UMTS and
GPRS

73423 VS.SRVCC.U2GERAN.SuccRelocPrepO Number of


BSC6 WRF
289
utPS
Successful
910
DOutgoing
02030
Inter-RAT PS
802
Handover
Preparations
Triggered by
SRVCC for
VoIP
Services for
Cell

PS
Handover
Between
UMTS and
GPRS

73423 VS.SRVCC.U2GERAN.SuccRelocOutPS Number of


BSC6 WRF
290
Successful
910
DOutgoing
02030
Inter-RAT PS
802
Handovers

PS
Handover
Between
UMTS and
GPRS

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73424 VS.HSUPA.TTI2to10.ADMCE.Succ
209

Number of
BSC6 WRF
Successful
910
DTTI
01061
Switchovers
404
Based on
Admitted
CEs During
RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

73424 VS.HSUPA.TTI2to10.COVER.Succ
210

Number of
BSC6 WRF
Successful
910
DTTI
01069
Switchovers
0
Based on
WRF
Coverage
DDuring RB
01061
Reconfigurat
404
ion in a
Cell(2ms to
10ms)

TTI Switch
for BE
Services
Based on
Coverage
HSUPA
2ms/10ms
TTI
Handover

73424 VS.HSUPA.TTI2to10.ResRTWP.Succ
211

Number of
BSC6 WRF
Successful
910
DTTI
01061
Switchovers
404
Based on
RTWP
During RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

Triggered by
SRVCC for
VoIP
Services for
Cell

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73424 VS.HSUPA.TTI2to10.ResUsedCE.Succ
212

Number of
BSC6 WRF
Successful
910
DTTI
01061
Switchovers
404
Based on
Number of
Occupied
CEs During
RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

73424 VS.HSUPA.TTI2to10.ResIUB.Succ
471

Number of
BSC6 WRF
Successful
910
DTTI
01061
Switchovers
404
Based on Iub
Resources
During RB
Reconfigurat
ion in a
Cell(2ms to
10ms)

HSUPA
2ms/10ms
TTI
Handover

73425 VS.IRATHO.FailOutCS.SCRI
007

Number of
BSC6 WRF
Failed CS
910
DOutgoing
02030
Inter-RAT
3
Handovers
WRF
for
DCell(Signalli
02030
ng
5
Connection
WRF
Release
DIndication)
02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutPSUTRAN.SCRI
008

Number of
Failed PS
Outgoing

BSC6 WRF Inter-RAT


910
DHandover
02030 Based on

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

3
WRF
D02030
5
WRF
D02030
6

Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutPSUTRAN.NoSRN
009
SDataForwardCmd

Number of
BSC6 WRF
Failed PS
910
DOutgoing
02030
Inter-RAT
3
Handovers
WRF
for Cell(No
DSRNS DATA
02030
Forward
5
cmd)
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.AttOutPSUTRAN.Sig
010

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
3
Attempts
WRF
When only
DSignaling
02030
Exists for
5
Cell
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.SuccOutPSUTRAN.Sig
011

Number of
BSC6 WRF
Successful
910
DPS Outgoing
02030
Inter-RAT
3
Handovers
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT

Inter-RAT
Handovers
for
Cell(Signalli
ng
Connection
Release
Indication)

NE

Count
er ID

Counter Name

Counter
Description
When only
Signaling
Exists for
Cell

NE

Featu
re ID

Feature
Name

D02030
5
WRF
D02030
6

Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutCS.InterRatRF
012

Number of
Failed CS
Outgoing
Inter-RAT
Handovers
for
Cell(Failure
in the Radio
Interface
Procedure)

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHO.FailOutPSUTRAN.InterRat
013
RF

Number of
Failed PS
Outgoing
Inter-RAT
Handovers
for
Cell(Failure
in the Radio
Interface
Procedure)

BSC6 WRF
910
D02030
3
WRF
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.HHO.AttInterFreqOut.Sig
014

Number of
InterFrequency
Hard
Handover
Attempts
When only
Signaling

BSC6 WRF
910
D02030
2
WRF
D02030

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter

Count
er ID

Counter Name

Counter
Description
Exists for
Cell

NE

Featu
re ID
4

Feature
Name
Frequency
Hard
Handover
Based on
DL QoS

73425 VS.HHO.SuccInterFreqOut.Sig
015

Number of
Successful
InterFrequency
Hard
Handover
Attempts
When only
Signaling
Exists for
Cell

BSC6 WRF
910
D02030
2
WRF
D02030
4

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73425 VS.MultiRAB.PSAbnormRel.ResumeEx
016
p

Number of
BSC6 WRF
Abnormal PS 910
DService
02030
Releases in
3
the Case of
WRF
Multi-RAB
DServices for
02030
Cell during
5
an inter-RAT
WRF
handover( PS
DResume
02030
Timer
6
Expiry)

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73425 VS.IRATHOCS.Cancel.ReEstab
926

Number of
BSC6 WRF
RL
910
DReestablishm
02030
ent Attempts
3
After UEs
WRF
Failed to
DReceive the
02030
CS Outgoing
6
Inter-RAT
WRF

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Load
Inter-RAT

Count
er ID

Counter Name

Counter
Description
Handover
Command
for Cell

NE

Featu
re ID

Feature
Name

DHandover
02030 Based on
5
Service

73425 VS.IRATHOPS.Cancel.ReEstab
927

Number of
BSC6 WRF
RL
910
DReestablishm
02030
ent Attempts
3
After UEs
WRF
Failed to
DReceive the
02030
PS Outgoing
6
Inter-RAT
WRF
Handover
DCommand
02030
for Cell
5

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Load
Inter-RAT
Handover
Based on
Service

73425 VS.IRATHO.AttNACC
954

Number of
BSC6 WRF
Attempts to 910
DObtain GSM
02030
System
801
Information
MRF
during RIMDbased
09021
NACCs
1
Triggered by
Inter-RAT PS
Handovers
for Cell

NACC(Net
work
Assisted
Cell
Change)
eCoordinat
or based
RIM
process
optimizatio
n

73425 VS.IRATHO.SuccNACC
955

Number of
BSC6 WRF
Successful
910
DThat GSM
02030
System
801
Information
MRF
Is Obtained
Dduring RIM09021
based
1
NACCs
Triggered by
Inter-RAT PS
Handovers

NACC(Net
work
Assisted
Cell
Change)
eCoordinat
or based
RIM
process
optimizatio
n

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

Number of
BSC6 WRF
Failed
910
DOutgoing
02040
Inter-RAT
002
CS
WRF
Handovers
DDue to
02030
Abnormal
3
Connection
WRF
Release by
DCN for Cell
02030
(Unspecified
5
Failure)
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73426 VS.IRATHO.FailOutPSUTRAN.CNUnsp Number of


BSC6 WRF
857
ecFail
Failed
910
DOutgoing
02040
Inter-RAT PS
002
Handovers
WRF
Due to
DAbnormal
02030
Connection
3
Release by
WRF
CN for Cell
D(Unspecified
02030
Failure)
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73426 VS.IRATHO.AttOutMultiRABCSPS
858

Inter
System
Direct
Retry
Inter-RAT

for Cell
73426 VS.IRATHO.FailOutCS.CNUnspecFail
856

Number of
Inter-RAT
Handover
Attempts
Initiated by

BSC6 WRF
910
D02040
002
WRF

Count
er ID

Counter Name

Counter
Description

Featu
re ID

Feature
Name

D02030
3
WRF
D02030
5
WRF
D02030
6

Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73426 VS.IRATHO.SuccOutMultiRABCSPS
859

Number of
BSC6 WRF
Successful
910
DInter-RAT
02040
Handovers
002
Initiated by
WRF
CS+PS (One
Dor Multiple)
02030
Combined
3
Services for
WRF
Cell
D02030
5
WRF
D02030
6

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73428 IRATHO.AttOutCS.Retry
084

Number of
BSC6 WRF
CS Outgoing 910
DInter-RAT
02040
Handover
002
Reattempts
WRF
for Cell
D02030
3
WRF
D02030
5

Inter
System
Direct
Retry
Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service

CS+PS (One
or Multiple)
Combined
Services for
Cell

NE

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

WRF
D02030
6

Inter-RAT
Handover
Based on
Load

73428 IRATHO.AttOutPSUTRAN.Retry
085

Number of
BSC6 WRF
PS Outgoing 910
DInter-RAT
02030
Handover
3
Reattempts
WRF
for Cell
D02030
5
WRF
D02030
6

Inter-RAT
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Service
Inter-RAT
Handover
Based on
Load

73428 VS.HHO.AttInterFreqOut.CSPS
086

Number of
BSC6 WRF
Outgoing
910
DInter02030
frequency
2
Hard
WRF
Handover
DAttempts for
02030
CS+PS
4
Combined
Services for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on
DL QoS

73428 VS.HHO.SuccInterFreqOut.CSPS
087

Number of
Successful
Outgoing
Interfrequency
Hard
Handovers
for CS+PS
Combined
Services for
Cell

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter
Frequency
Hard
Handover
Based on

BSC6 WRF
910
D02030
2
WRF
D02030
4

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name
DL QoS

73428 VS.HSPA.ServCellChg.1A1COptTrig
444

Number of
BSC6 WRF
HSPA
910
DServing Cell
01061
Changes
006
Triggered by
WRF
Event 1A or
D1C for Cell
01061
204

HSDPA
Mobility
Manageme
nt
HSUPA
Mobility
Manageme
nt

73428 VS.HSPA.ServCellChg.1DOptTrig
445

Number of
BSC6 WRF
HSPA
910
DServing Cell
01061
Changes
006
Triggered by
WRF
Event 1D for
DCell
01061
204

HSDPA
Mobility
Manageme
nt
HSUPA
Mobility
Manageme
nt

73428 VS.CM.DLSF2.AltScramCode.UE.Max
665

Max Number BSC6 WRF


Of Ues with 910
DSf2AltScram
02030
Code In a
2
Cell
WRF
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

73428 VS.CM.DLSF2.UE.Max
668

Max Number BSC6 WRF


Of Ues with 910
DSf2 In a Cell
02030
2
WRF
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

Count
er ID

Counter Name

Counter
Description

NE

Featu
re ID

Feature
Name

73444 VS.CM.DLSF2.AltScramCode.UE.Mean
434

Average
BSC6 WRF
number of
910
DUes with
02030
Sf2AltScram
2
Code in a
WRF
cell
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

73444 VS.CM.DLSF2.UE.Mean
435

Average
BSC6 WRF
Number Of 910
DUes with Sf2
02030
In a Cell
2
WRF
D02030
3

Inter
Frequency
Hard
Handover
Based on
Coverage
Inter-RAT
Handover
Based on
Coverage

19 Glossary
For the acronyms, abbreviations, terms, and definitions, see Glossary.

20 Reference Documents
1.

3GPP TS 23.122, "Non Access Stratum functions related to Mobile Station (MS) in idle mode"

2.

3GPP TS 24.008, "Mobile radio interface layer 3 specification; Core Network Protocols - Stage 3"

3.

3GPP TS 25.304, "UE Procedures in Idle Mode and Procedures for Cell Reselection in
Connected Mode"

4.

3GPP TS 25.331, "RRC Protocol Specification"

5.

3GPP TS 23.060, "General Packet Radio Service (GPRS); Service description"

6.

3GPP TS 25.931, "UTRAN Functions, Examples on Signaling Procedures"

7.

Directed Retry Decision Feature Parameter Description

8.

CE Resource Management Feature Parameter Description

9.

Load Control Feature Parameter Description

10.

Interoperability Between UMTS and LTE Feature Parameter Description

11.

AMR Feature Parameter Description

12.

DCCC Feature Parameter Description

13.

UE Behaviors in Idle Mode Feature Parameter Description

14.

License Management Feature Parameter Description

15.

Inter-Frequency Load Balancing Feature Parameter Description

You might also like