Professional Documents
Culture Documents
MW-BSP-13-0162
250729
iPASOLINK 400
Version R3.7
IEEE1588 (2008) Function Description
NEC Corporation
Note: This technical description shows all available functions. The specific functions are made
available with eligible combination of hardwares and softwares. Please refer to the valid price list
to be ordered to activate the specific functionality.
This document describes the current version of NEC standard equipment. If there is any conflict between
this document and the System Description and/or the Compliance statement, the latter will supersede this
document.
The specifications or configuration contained in this document are subject to change without notice due to
NEC's continuing design improvement.
Windows and Windows Vista are registered trademarks of Microsoft Corporation. UNIX is a registered
trademark of The Open Group.
MWS-BSP-13-0162
iPASOLINK 400
TABLE OF CONTENTS
1
INTRODUCTION ............................................................................................... 1
GENERAL FEATURES..................................................................................... 2
2.1
2.2
2.3
2.4
2.5
Principles........................................................................................................... 2
Boundary Clock Function .................................................................................. 2
Ordinary clock slave function ............................................................................ 2
Ordinary clock slave function with SyncE .......................................................... 3
Transparent clock function ................................................................................ 3
SPECIFICATIONS ............................................................................................ 3
3.1
3.2
Performance ..................................................................................................... 3
Reference specifications ................................................................................... 3
Provisioning .................................................................................................. 13
5.1
5.2
General ........................................................................................................... 16
Measurement block diagram ........................................................................... 17
6.1
6.2
6.3
6.4
7.1
7.2
PERFORMANCE ............................................................................................ 28
8.1
8.2
General ........................................................................................................... 28
ToD format ...................................................................................................... 29
-i-
1 INTRODUCTION
iPASOLINK400 R3.7 have applied IEEE1588 (2008) Precision Time Protocol as Ordinary
clock and Boundary clock function. This function is realized with PTP-A panel in universal
slots that equipped high accuracy and stable oven controlled crystal oscillator.
Figure 1.1 iPASOLINK400 IDU outline and PTP-A card front face
iPASOLINK 400
*Not support ordinary clock ground master and transparent clock mode
**Boundary clock needs software key
Ordinary Clock
Master
Boundary
Clock
Network
iPASO400 MWS-BSP-13-0162
- 1-
Ordinary
Clock Slave
2 GENERAL FEATURES
2.1 Principles
2.2 Boundary Clock Function
Boundary clock operates synchronization on master clock. And operate as master clock
for lower level network. This reduces the loads on the master clock.
Boundary Clock
Network #1
Network #2
PTP
Network #3
Master
Clock
Network #4
Slave Clock
Master Clock
10MHz
1PPS
Network #A
eNB
ToD
Equivalent interface as GPS
-2-
iPASO400 MWS-BSP-13-0162
Slave Clock
Master Clock
10MHz
1PPS
Network #A
eNB
ToD
SyncE
This function compensates delay time that generated in own equipment and rewrite time
stamp data. But this function operates without high-accuracy oscillator, therefore the time
stamp accuracy not be improved in this process.
Transparent clock
Master Clock
Network
Network #1
3 SPECIFICATIONS
3.1
Performance
Ordinary Clock slave and Boundary Clock of IEEE1588v2 (IEEE1588-2008) are supported
3.2
Reference specifications
ITU-T G.8260: Definitions and terminology for synchronization in packet networks
ITU-T G.8265.1: Precision time protocol telecom profile for frequency synchronization
ITU-T G.8271: Time and phase synchronization aspects of packet networks
IEEE1588-2008: Precision time protocol
iPASO400 MWS-BSP-13-0162
- 3-
4 Provisioning
4.1 Ordinary clock function setting
iPASO400 MWS-BSP-13-0162
- 13 -
(1)
(2)
(4)
(5)
4.2
- 14 -
iPASO400 MWS-BSP-13-0162
(3)
(1)
(2)
(4)
(3)
(5)
(6)
Figure.4.3.1 Warm up
iPASO400 MWS-BSP-13-0162
- 15 -
Radio link
OC Slave
- 16 -
iPASO400 MWS-BSP-13-0162
5.2
iPASO400 MWS-BSP-13-0162
- 17 -
Figure.5.2.2 Measurement block diagram for PTP with SyncE mode with Paragon-X
- 18 -
iPASO400 MWS-BSP-13-0162
+/- 250[nsec]
TIE [ns]
500
-500
-1000
-1500
0
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
Time [Sec]
1500
TIE
1000
TIE [ns]
500
+/- 250[nsec]
-500
-1000
-1500
0
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
Time [Sec]
E1 TIE(phase stability)
Spec.Only reference
ResultMax.+/- 250nsec
iPASO400 MWS-BSP-13-0162
- 19 -
- 20 -
iPASO400 MWS-BSP-13-0162
6.2
1500
TIE
1000
+/- 150[nsec]
TIE [ns]
500
-500
-1000
-1500
0
1000
2000
3000
4000
5000
Time [Sec]
6000
7000
8000
9000
10000
1500
TIE
1000
+/- 170[nsec]
TIE [ns]
500
-500
-1000
-1500
0
1000
2000
3000
E1 TIE(phase stability)
4000
5000
Time [Sec]
6000
7000
8000
Spec.Only reference
ResultMax.170nsec
iPASO400 MWS-BSP-13-0162
9000
- 21 -
10000
Figure.6.2.3 Measurement result 1PPS MTIE and TDEV on PTP mode 64fps
E1(2MHz) MTIE,
Figure.6.2.4 Measurement result E1 (2Mbps) MTIE and TDEV on PTP mode 64fps
- 22 -
iPASO400 MWS-BSP-13-0162
6.3
TIE
1000
+/- 40[nsec]
TIE [ns]
500
-500
-1000
-1500
0
1000
2000
3000
4000
5000
Time [Sec]
6000
7000
8000
9000
10000
Figure.6.3.1 Measurement result 1PPS with SyncE mode TIE on PTP mode 64fps
1500
TIE
1000
TIE [ns]
500
-500
-1000
-1500
0
1000
2000
3000
4000
5000
Time [Sec]
6000
7000
8000
9000
10000
iPASO400 MWS-BSP-13-0162
- 23 -
Figure.6.3.3 Measurement result 1PPS MTIE and TDEV on PTP with SyncE mode 64fps
Figure.6.3.4 Measurement result E1 (2Mbps) MTIE and TDEV on PTP with SyncE mode
64fps
- 24 -
iPASO400 MWS-BSP-13-0162
6.4
PTP
flow rate
SyncE
assist
1PPS TIE
Spec. +/1.5usec
MTIE Mask
TDEV Mask
[fps]
[usec]
PTP Mode
16
+/- 0.25
good
good
PTP Mode
64
+/- 0.15
good
good
64
ON
+/- 0.04
good
good
iPASO400 MWS-BSP-13-0162
- 25 -
- 26 -
iPASO400 MWS-BSP-13-0162
iPASO400 MWS-BSP-13-0162
- 27 -
8 PERFORMANCE
8.1 General
ITEM
SPECIFICATION
Frequency stability
Interface Port
ENVIRONMENTAL
Temperature, Operational
Humidity, Operational
0 to 95 %
Transportation / Storage
EMC
EN301489-1, EN301489-4
CISPR 22 Class A
SAFETY
EN60950, UL60950
EN62311
EN50371, EN62749
POWER REQUIREMENT
Input Voltage
Power Consumption
MECHANICAL
Dimensions (W x H x D)
Without ODU
Approx.4 kg
MTD-PL-059/250405
I/O
Out
Out
Reserved
Reserved
TODOUT_N
TODOUT_P
V.11
Out
4800bps / Data: 8bit /
Parity: None / Stop bit:
Out
1bit
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
FG
GND
GND
GND
iPASO400 MWS-BSP-13-0162
Reserved
MTD-PL-059/250405