Professional Documents
Culture Documents
____________________________Features
o 200ms Power-OK/Reset Timeout Period
o 1A Standby Current, 30A Operating Current
o On-Board Gating of Chip-Enable Signals,
10ns max Delay
o MaxCap or SuperCap Compatible
o Guaranteed RESET Assertion to VCC = +1V
o Voltage Monitor for Power-Fail or Low-Battery
Warning
o Power-Fail Accuracy Guaranteed to 2%
(MAX800L/M)
o Available in 16-Pin Narrow SO, Plastic
DIP, and TSSOP Packages
________________________Applications
Ordering Information
Computers
PART
Controllers
PINPACKAGE
Intelligent Instruments
MAX691ACUE
-0C to +70C
16 TSSOP
Automotive Systems
MAX691ACSE
-0C to +70C
16 Narrow SO
MAX691ACWE
-0C to +70C
16 Wide SO
MAX691ACPE
-0C to +70C
16 Plastic DIP
TEMP RANGE
5V
REGULATOR
0.1F
3
VCC
1N4148
1
5
BATT ON
VOUT
VBATT
CE OUT
0.47F*
MAX691AC/D
-0C to +70C
Dice*
MAX691AEUE
-0C to +70C
16 TSSOP
MAX691AESE
-40C to +85C
16 Narrow SO
MAX691AEWE
-40C to +85C
16 Wide SO
MAX691AEPE
-40C to +85C
16 Plastic DIP
2
12
CMOS RAM
MAX691A
9
MAX693A CE IN 13
PFI
MAX800L
MAX800M
4
GND
WDI
7
NO
CONNECTION
TOP VIEW
A0-A15
I/O
11
OSC IN
PFO 10
Pin Configuration
ADDRESS
DECODE
NMI
OSC SEL
LOW LINE WDO
6
14
RESET
15
RESET
VBATT 1
16 RESET
VOUT 2
15 RESET
VCC 3
GND 4
BATT ON 5
LOW LINE 6
AUDIBLE
ALARM
14 WDO
MAX691A
MAX693A
MAX800L
MAX800M
OSC IN 7
12 CE OUT
11 WDI
10 PFO
OSC SEL 8
*MaxCap
13 CE IN
PFI
DIP/SO/TSSOP
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxims website at www.maxim-ic.com.
MAX691A/MAX693A/MAX800L/MAX800M
General Description
MAX691A/MAX693A/MAX800L/MAX800M
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(MAX691A, MAX800L: VCC = +4.75V to +5.5V; MAX693A, MAX800M: VCC = +4.5V to +5.5V; VBATT = 2.8V, TA = TMIN to TMAX,
unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Voltage Range,
VCC, VBATT (Note 1)
0
IOUT = 25mA
VOUT Output
VCC = 4.5V
IOUT = 250mA
5.5
MAX69_AC
VCC - 0.02
VCC - 0.2
VCC - 0.05
VCC - 0.3
MAX69_AE,
MAX800_C/E
VCC - 0.2
VCC - 0.35
MAX69_A/M
IOUT = 210mA
VOUT in Battery-Backup
Mode
VBATT-to-VOUT
On-Resistance
VCC - 0.17
VCC - 0.3V
MAX69_AC, MAX800_C
0.8
1.2
MAX69_AE, MAX800_E
0.8
1.4
0.8
1.6
Supply Current in
Normal Operating Mode
(excludes IOUT)
Supply Current in
Battery-Backup Mode
(excludes IOUT) (Note 2)
Battery Switchover
Threshold
Power-up
Power-down
TA = +25C
TA = TMIN + TMIN
VCC - 0.40
MAX69_AC/AE,
MAX800_C/E
MAX69_A/M
VBATT = 4.5V, IOUT = 20mA
VBATT = 2.8V, IOUT = 10mA
VBATT = 2.0V, IOUT = 5mA
VBATT = 4.5V
VBATT = 2.8V
VBATT = 2.0V
VBATT - 0.3
VBATT - 0.25
VBATT - 0.15
V
15
25
30
30
100
0.04
1
A
5
-0.1
-1.0
0.02
0.02
VBATT + 0.3
VBATT - 0.3
_______________________________________________________________________________________
A
V
(MAX691A, MAX800L: VCC = +4.75V to +5.5V; MAX693A, MAX800M: VCC = +4.5V to +5.5V; VBATT = 2.8V, TA = TMIN to TMAX,
unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
Battery Switchover
Hysteresis
TYP
MAX
60
100
4.50
4.65
4.75
MAX693A, MAX800M
4.25
4.40
4.50
4.55
4.30
BATT ON Output
Short-Circuit Current
ISINK = 3.2mA
ISINK = 25mA
Sink current
Source current
mV
0.1
0.7
60
15
BATT ON Output
Low Voltage
Power-down
140
100
ISINK = 3.2mA
ISOURCE = 500A, VCC = 5V
WDO Output
Short-Circuit Current
VIH
VIL
WDI = 0V
WDI = VOUT
4.70
V
mA
A
4.45
15
mV
80
800
ns
200
280
1.6
100
4096
1024
ms
Clock
Cycles
2.25
140
sec
ms
Clock
Cycles
ns
0.004
0.1
0.3
0.4
20
mA
3.5
0.4
1.5
2048
Long period
Short period
Long period
Short period
UNITS
0.1
0.4
V
0.4
3.5
1
15
100
0.4
3.5
3
10
0.75 x VCC
0.8
-50
-10
20
50
V
A
V
mA
V
A
_______________________________________________________________________________________
MAX691A/MAX693A/MAX800L/MAX800M
MAX691A/MAX693A/MAX800L/MAX800M
CONDITIONS
MIN
TYP
MAX
1.2
1.25
1.3
1.225
1.25
1.275
0.01
25
UNITS
POWER-FAIL COMPARATOR
PFI Input Threshold
MAX69_AC/AE/AM, VCC = 5V
MAX800_C/E, VCC = 5V
ISINK = 3.2mA
ISOURCE = 1A, VCC = 5V
Output source current
0.4
3.5
1
15
25
60
100
V
nA
V
A
s
CHIP-ENABLE GATING
CE IN Leakage Current
Disable mode
0.005
Enable mode
75
150
0.75
2.0
mA
10
ns
0.1
3.5
2.7
Power-down
V
12
INTERNAL OSCILLATOR
OSC IN Leakage Current
OSC SEL = 0V
0.10
10
100
OSC SEL = 0V
10
100
OSC SEL = 0V
VIH
50
VOUT - 0.3
kHz
VOUT - 0.6
VIL
3.65
100
2.00
V
kHz
Note 1: Either VCC or VBATT can go to 0V, if the other is greater than 2.0V.
Note 2: The supply current drawn by the MAX691A/MAX800L/MAX800M from the battery excluding IOUT typically goes to 10A
when (VBATT - 1V) < VCC < VBATT. In most applications, this is a brief period as VCC falls through this region.
Note 3: + = battery-discharging current, -- = battery-charging current.
Note 4: Although presented as typical values, the number of clock cycles for the reset and watchdog timeout periods are fixed and
do not vary with process or temperature.
Note 5: RESET is an open-drain output and sinks current only.
Note 6: WDI is internally connected to a voltage divider between VOUT and GND. If unconnected, WDI is driven to 1.6V (typ),
disabling the watchdog function.
Note 7: The chip-enable resistance is tested with VCC = +4.75V for the MAX691A/MAX800L and VCC = +4.5V for the
MAX693A/MAX800M. CE IN = CE OUT = VCC/2.
Note 8: The chip-enable propagation delay is measured from the 50% point at CE IN to the 50% point at CE OUT.
4
_______________________________________________________________________________________
32
30
28
26
-30
30
60
90
120
0.5
150
-30
30
60
90
120
60
30
90
120
5
-30
30
60
90
120
1.0
0.9
0.8
0.7
0.75
0.50
VCC = +5V,
VBATT = 0V
NO LOAD ON PFO
0.25
0.6
150
1.00
0
-60
-30
30
60
90
120
150
-60
-30
30
60
90
TEMPERATURE (C)
TEMPERATURE (C)
RESET THRESHOLD
vs. TEMPERATURE
RESET DELAY
vs. TEMPERATURE
4.55
4.50
4.45
4.40
MAX693A
MAX800M
4.30
400
300
200
100
30
60
90
TEMPERATURE (C)
120
150
120
150
210
200
190
180
170
0
0
MAX691A TOC-09
500
150
VCC = 0V TO 5V STEP
VBATT = 2.8V
220
RESET DELAY (ms)
MAX691A
MAX800L
120
230
MAX691A TOC-08
4.70
600
RESET OUTPUT RESISTANCE ()
MAX691A TOC-07
TEMPERATURE (C)
VBATT = 2.8V
-30
1.25
PFI THRESHOLD (V)
1.1
MAX691A TOC-06
VCC = 5V,
VBATT = 0V
150 180
1.50
MAX691A TOC-05
VCC-to-VOUT ON-RESISTANCE ()
MAX691A TOC-04
1.2
VCC = 0V
-60
-60 -30
150
PFI THRESHOLD
vs. TEMPERATURE
VBATT = 4.5V
4.35
40
-60
10
4.60
60
VBATT = 2.8V
4.65
80
TEMPERATURE (C)
15
4.75
100
TEMPERATURE (C)
VBATT = 2.0V
-60
VCC = 4.75V
VBATT = 2.8V
VCE IN = VCC/2
TEMPERATURE (C)
20
VBATT-to-VOUT ON-RESISTANCE ()
1.5
120
0
-60
VCC = 5V
VBATT = 2.8V
NO LOAD
CE ON-RESISTANCE ()
34
MAX691A TOC-02
MAX691A TOC-01
VCC = 5V
VBATT = 2.8V
PFI, CE IN = 0V
36
CHIP-ENABLE ON-RESISTANCE
vs. TEMPERATURE
MAX691A TOC-03
-60
-30
30
60
90
TEMPERATURE (C)
120
150
-60
-30
30
60
90
TEMPERATURE (C)
_______________________________________________________________________________________
MAX691A/MAX693A/MAX800L/MAX800M
LONG WATCHDOG
TIMEOUT PERIOD
20
12
VCC = 5V
VBATT = 2.8V
10
RESET ACTIVE
TIMEOUT PERIOD
1
SHORT WATCHDOG
TIMEOUT PERIOD
16
12
0.1
3
100
1000
150
200
CLOAD (pF)
1000
SLOPE = 0.8
VCC = 0V
VBATT = 4.5V
5V
VCC RESET
THRESHOLD
80s
100
HI
LOW LINE
LO
10
RESET
LO
HI
100
IOUT (mA)
1000
12s
LO
1
10
800ns
HI
SLOPE = 8
CE OUT
100
COSC (pF)
100
50
VCC (V)
VCC = 4.5V
VBATT = 0V
10
0
10
10
250
300
MAX691A TOC-15
1000
MAX691A TOC-13
VCC = 5V
CE IN = 0V
TO 5V
DRIVER SOURCE
MAX691A TOC-14
IBATT (A)
16
100
MAX691A TOC-11
VBATT = 2.8V
IOUT = 0A
MAX691A TOC-10
20
MAX691A TOC-12
BATTERY CURRENT
vs. INPUT SUPPLY VOLTAGE
MAX691A/MAX693A/MAX800L/MAX800M
100
IOUT (mA)
_______________________________________________________________________________________
PIN
NAME
FUNCTION
VBATT
VOUT
Battery-Backup Input. Connect to external battery or capacitor and charging circuit. If backup battery is not
used, connect to GND.
Output Supply Voltage. When VCC is greater than VBATT and above the reset threshold, VOUT connects to
VCC. When VCC falls below VBATT and is below the reset threshold, VOUT connects to VBATT. Connect a 0.1F
capacitor from VOUT to GND. Connect VOUT to VCC if no backup battery is used.
Input Supply Voltage, 5V Input.
VCC
GND
5
6
8
9
10
11
12
13
14
15
16
_______________Detailed Description
_______________________________________________________________________________________
MAX691A/MAX693A/MAX800L/MAX800M
______________________________________________________________Pin Description
MAX691A/MAX693A/MAX800L/MAX800M
WDI
RESET
MAX691A
MAX693A
15
TO P RESET
WDO
1k
t2
RESET
t1
t1
t3
Watchdog Output
The Watchdog Output (WDO) remains high if there is a
transition or pulse at WDI during the watchdog timeout
Watchdog Function
The watchdog monitors P activity via the Watchdog
Input (WDI). If the P becomes inactive, RESET and
RESET are asserted. To use the watchdog function,
connect WDI to a bus line or P I/O line. If WDI
remains high or low for longer than the watchdog timeout period (1.6s nominal), WDO, RESET, and RESET
are asserted (see RESET and RESET Outputs section,
and the Watchdog Output discussion on this page).
Watchdog Input
A change of state (high to low, low to high, or a minimum 100ns pulse) at the WDI during the watchdog
period resets the watchdog timer. The watchdog
default timeout is 1.6s.
To disable the watchdog function, leave WDI floating.
An internal resistor network (100k equivalent impedance at WDI) biases WDI to approximately 1.6V.
Internal comparators detect this level and disable the
watchdog timer. When VCC is below the reset threshold, the watchdog function is disabled and WDI is disconnected from its internal resistor network, thus
becoming high impedance.
8
Selecting an Alternative
Watchdog and Reset Timeout Period
The OSC SEL and OSC IN inputs control the watchdog
and reset timeout periods. Floating OSC SEL and OSC
IN or tying them both to VOUT selects the nominal 1.6s
watchdog timeout period and 200ms reset timeout period. Connecting OSC IN to GND and floating or connecting OSC SEL to V OUT selects the 100ms normal
watchdog timeout delay and 1.6s delay immediately
after reset. The reset timeout delay remains 200ms
(Figure 2). Select alternative timeout periods by connecting OSC SEL to GND and connecting a capacitor
between OSC IN and GND, or by externally driving OSC
IN (Table 1 and Figure 3). OSC IN is internally connected to a 100nA (typ) current source that charges and
discharges the timing capacitor to create the oscillator
frequency, which sets the reset and watchdog timeout
periods (see Connecting a Timing Capacitor at OSC IN
in the Applications Information section).
_______________________________________________________________________________________
OSC SEL
OSC IN
Low
1024 clks
4096 clks
2048 clks
Low
External Capacitor
(600/47pF x C)ms
(2.4/47pF x C)sec
(1200/47pF x C)ms
Floating
Low
100ms
1.6s
200ms
Floating
Floating
1.6s
1.6s
200ms
Normal
EXTERNAL
OSCILLATOR
EXTERNAL
CLOCK
MAX691A
MAX693A
MAX800L
MAX800M
OSC SEL
OSC IN
OSC SEL
OSC IN
50kHz
INTERNAL OSCILLATOR
1.6s WATCHDOG
N.C.
N.C.
OSC SEL
OSC IN
INTERNAL OSCILLATOR
100ms WATCHDOG
N.C.
OSC SEL
OSC IN
Chip-Enable Input
The Chip-Enable Input (CE IN) is high impedance (disabled mode) while RESET and RESET are asserted.
During a power-down sequence where VCC falls below
Chip-Enable Output
In the enabled mode, the impedance of CE OUT is
equivalent to 75 in series with the source driving CE
IN. In the disabled mode, the 75 transmission gate is
off and CE OUT is actively pulled to VOUT. This source
turns off when the transmission gate is enabled.
Power-Fail Comparator
The power-fail comparator is an uncommitted comparator
that has no effect on the other functions of the IC.
Common uses include low-battery indication (Figure 7),
and early power-fail warning (see Typical Operating
Circuit).
Power-Fail Input
Power-Fail Input (PFI) is the input to the power-fail comparator. It has a guaranteed input leakage of 25nA
max over temperature. The typical comparator delay is
25s from VIL to VOL (power failing), and 60s from VIH
to VOH (power being restored). If PFI is not used, connect it to ground.
_______________________________________________________________________________________
MAX691A/MAX693A/MAX800L/MAX800M
MAX691A/MAX693A/MAX800L/MAX800M
BATT ON
4.65V*
VCC
3
2
VBATT
CE IN
1
13
12
MAX691A
MAX693A
MAX800L
MAX800M
OSC SEL
WDI
PFI
RESET
GENERATOR
15
TIMEBASE FOR
RESET AND
WATCHDOG
WATCHDOG
TRANSITION
DETECTOR
11
9
WATCHDOG
TIMER
14
10
1.25V
4 GND
* 4.4V FOR THE MAX693A/MAX800M
5.0V
VCC
RESET
4.0V
THRESHOLD
5.0V
0V
CE IN
5V
0V
CE OUT
15s
100s
5V
0V
5V
100s
RESET
RESET
0V
LOGIC LEVELS SHOWN ARE FROM 0V TO 5V.
VOUT
CHIP-ENABLE
OUTPUT
CONTROL
16
OSC IN
LOW LINE
______________________________________________________________________________________
CE OUT
RESET
RESET
WDO
PFO
VBATT
+5V
VCC
MAX691A
MAX693A
MAX800L
MAX800M
2.8V
2.0V to 5.5V
CE OUT
CE IN
50
OUTPUT
IMPEDANCE
VCC
VBATT
GND
CLOAD
MAX691A
MAX693A
MAX800L PFO
PFI
MAX800M
LOW BATT
GND
Power-Fail Output
The Power-Fail Output (PFO) goes low when PFI goes
below 1.25V. It typically sinks 3.2mA with a saturation
voltage of 0.1V. With PFI above 1.25V, PFO is actively
pulled to VOUT.
PIN
NAME
VBATT
VOUT
STATUS
Supply current is 1A max.
VOUT is connected to VBATT through an
internal PMOS switch.
VCC
GND
BATT ON
LOWLINE
Logic low*
OSC IN
OSC SEL
PFI
PFO
10
OSC IN is ignored.
OSC SEL is ignored.
11
WDI
Watchdog is ignored.
12
CE OUT
13
CE IN
High impedance
14
WDO
15
RESET
Logic low*
16
RESET
High impedance*
Battery-Backup Mode
Two conditions are required to switch to battery-backup mode: 1) VCC must be below the reset threshold,
and 2) VCC must be below VBATT. Table 2 lists the status of the inputs and outputs in battery-backup mode.
Battery-On Output
The Battery-On (BATT ON) output indicates the status
of the internal V CC /battery-switchover comparator,
which controls the internal VCC and VBATT switches.
For VCC greater than VBATT (ignoring the small hysteresis effect), BATT ON typically sinks 3.2mA at 0.1V
saturation voltage. In battery-backup mode, this terminal sources approximately 10A from VOUT. Use BATT
ON to indicate battery-switchover status or to supply
base drive to an external pass transistor for higher-current applications (see Typical Operating Circuit).
11
MAX691A/MAX693A/MAX800L/MAX800M
+5V
MAX691A/MAX693A/MAX800L/MAX800M
__________Applications Information
The MAX691A/MAX693A/MAX800L/MAX800M are not
short-circuit protected. Shorting VOUT to ground, other
than power-up transients such as charging a decoupling capacitor, destroys the device.
All open-circuit outputs swing between VOUT and GND
rather than VCC and GND.
If long leads connect to the chip inputs, insure that
these leads are free from ringing and other conditions
that would forward bias the chips protection diodes.
There are three distinct modes of operation:
+5V
3
VCC
1N4148
VBATT
MAX691A
MAX693A
MAX800L
MAX800M
VOUT
0.47F*
0.1F
VCC
VBATT
VOUT
MAX691A
MAX693A
MAX800L
MAX800M
GND
4
* MaxCap
12
______________________________________________________________________________________
+5V
CE
CE
VOUT
CE IN
MAX691A/MAX693A/MAX800L/MAX800M
VIN
Rp*
R1
RAM 1
VCC
C1*
PFI
CE OUT
CE
CE
MAX691A
MAX693A
MAX800L
MAX800M
MAX691A
MAX693A
MAX800L
MAX800M
RAM 2
R3
R2
CE
CE
GND
PFO
RAM 3
GND
TO P
CE
*OPTIONAL
5V
RAM 4
PFO
CE
0V
0V
VL VTRIP VH
VIN
VTRIP = 1.25
*MAXIMUM Rp VALUE DEPENDS ON
THE NUMBER OF RAMS.
MINIMUM Rp VALUE IS 1k.
ACTIVE-HIGH
CE LINES
FROM LOGIC
VH = 1.25/
R1
VCC
PFO
PFI
MAX691A
MAX693A
MAX800L
MAX800M
R2
Hysteresis adds a noise margin to the power-fail comparator and prevents repeated triggering of PFO when
VIN is near the power-fail comparator trip point. Figure
11 shows how to add hysteresis to the power-fail com-
+5V
R2 I I R3
R1 + R2 I I R3
R1 + R2
R2
GND
5V
V-
PFO
0V
5 - 1.25 = 1.25 - VTRIP
R1
R2
VTRIP
V-
0V
______________________________________________________________________________________
13
VCC = 5V
TA = +25C
0.1F CAPACITOR
FROM VOUT TO GND
80
MAX791-16
Backup-Battery Replacement
100
MAXIMUM TRANSIENT DURATION (s)
MAX691A/MAX693A/MAX800L/MAX800M
60
40
20
0
10
100
1000
10000
14
______________________________________________________________________________________
START
SET
WDI
LOW
SUBROUTINE
OR PROGRAM LOOP
SET WDI
HIGH
RETURN
END
______________________________________________________________________________________
15
MAX691A/MAX693A/MAX800L/MAX800M
PINPACKAGE
MAX691AEJE
-40C to +85C
16 CERDIP
MAX691AMJE
-55C to +125C
16 CERDIP**
MAX691AMSE/PR
-55C to +125C
16 Wide SO**
MAX691AMSE/PR-T
-55C to +125C
16 Wide SO**
PART
MAX693ACUE
MAX693ACSE
-0C to +70C
-0C to +70C
16 Narrow SO
-0C to +70C
16 Wide SO
MAX693ACPE
-0C to +70C
16 Plastic DIP
MAX693AC/D
-0C to +70C
Dice*
MAX693AEUE
-40C to +85C
16 TSSOP
MAX693AESE
-40C to +85C
16 Narrow SO
MAX693AEWE
-40C to +85C
16 Wide SO
MAX693AEPE
-40C to +85C
16 Plastic DIP
MAX693AEJE
-40C to +85C
16 CERDIP
MAX693AMJE
-55C to +125C
16 CERDIP
MAX800LCUE
-0C to +70C
16 TSSOP
MAX800LCSE
-0C to +70C
16 Narrow SO
MAX800LCPE
-0C to +70C
16 Plastic DIP
MAX800LEUE
-40C to +85C
16 TSSOP
MAX800LESE
-40C to +85C
16 Narrow SO
MAX800LEPE
-40C to +85C
16 Plastic DIP
MAX800MCUE
-0C to +70C
16 TSSOP
-0C to +70C
16 Narrow SO
MAX800MCPE
-0C to +70C
16 Plastic DIP
MAX800MEUE
-40C to +85C
16 TSSOP
MAX800MESE
-40C to +85C
MAX800MEPE
-40C to +85C
VBATT
RESET
RESET
VCC
WDO
CE IN
GND
CE OUT
0.11"
(2.794mm)
BATT ON
LOW LINE
WDI
PFI PFO
OSC IN
OSC SEL
0.07"
(1.778mm)
Package Information
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages.
PACKAGE TYPE
PACKAGE CODE
16 Narrow SO
16 TSSOP
U16-1
21-0066
16 Plastic DIP
16 CERDIP
J16-3
21-0045
16 Narrow SO
S16-3
21-0041
16 Plastic DIP
P16-1
21-0043
16 Wide SO
W16-1
21-0042
16
VOUT
16 TSSOP
MAX693ACWE
MAX800MCSE
___________________Chip Topography
______________________________________________________________________________________
DOCUMENT NO.
REVISION
NUMBER
REVISION
DATE
09/92
Initial release
12/92
5/93
12/93
2, 3, 4
3/94
2, 3, 4
8/94
Correction to Figure 4.
DESCRIPTION
PAGES
CHANGED
2, 3, 4
2, 3, 4, 9, 11
10
1/95
12/96
2, 3, 4
12/99
1, 2, 16
4/02
10
11/05
1, 16
11
8/08
1, 16
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 17
2008 Maxim Integrated Products
MAX691A/MAX693A/MAX800L/MAX800M
Revision History