Professional Documents
Culture Documents
Product Catalog
Certified to ISO 9001:2000
CAST BRONZE
BEARINGS
CONTINUOUS AND
CENTRIFUGAL CAST
BRONZE BARS
ALUMINUM BRONZE
BAR AND WEARPLATE
POWDERED METAL
PRODUCTS
LUBE-ALIGN
MOUNTED BEARINGS
ENGINEERED
PLASTIC BEARINGS
Bunting Bearings
PV Data Chart
+For Bearing Selection in All Bearing Raw Materials
MAX. PV MAX. P MAX. V STDS.
1. VESPEL ®
Bearings 300,000 4,900 3,000 YES
All values are based on 72o room temperature and the standard
lubricant for the bearing in question. All of the V’s (and therefore the
PV’s) can be raised by special lubricating techniques.
Not all materials listed above are available from Bunting Bearings Corp.
PV CALCULATION
PV is a means of measuring the performance capabilities of bearings.
P is expressed as pressure or pounds per square inch on the projected
area of the bearing. V is velocity in feet per minute of the wear surface
(surface feet per minute).
For sleeve (plane) bearings, the surface speed is .262 (pi ÷12)
x RPM x shaft diameter in inches. P is equal to the load on the bearing in
pounds divided by the projected area in square inches. For sleeve
(plane) bearings, the projected area is the length x the inside diameter
of the bearing.
PV is then obtained by multiplying P x V as shown in the following
example:
3/4" shaft @ 341 RPM, 90 lb. total load, bearing length 1".
V = .262 x RPM x shaft diameter, or .262 x 341 x .750 = 67 sfpm.
P = total load ÷ projected area (area = .750 x 1.0 = .75 sq. in.), or
90 lbs. ÷ .75 = 120 psi.
PV = 120 psi x 67 sfpm = 8040 PV.
1
Table of Contents
Bunting® Products
Registered Trademarks
Bunting®, Lube-Align®, Dri-Plane®, BB-16® of Bunting Bearings Corp.,
VESPEL® and Delrin® of DuPont Co., JLON® of Jade Engineered
Plastics
FORM NO. A0093 25M 7/05 Printed in U.S.A.
2
Bunting C93200
Cast Bronze Sleeve (Plane) Bearings
Bunting cast bronze bearings are machined from continuous cast
C93200 (SAE 660) bronze for superior quality and performance. The
continuous casting process assures a uniform bronze structure
throughout the bearing, free from porosity and hard particle inclusions
commonly found in other cast processes.
Our standard bearing line features over 900 sizes, carried in
stock at Bunting Bearings and Authorized Distributors. These
standards provide off-the-shelf economy for most applications, and
may be easily resized, oil grooved, or graphited to meet special
requirements.
In addition to standard sleeve (plane) bearings, see your local
Bunting Bearings Authorized Distributor for:
• Machined to print bearings
• Precision finished bearings
• Grease or oil grooved bearings
• Graphite-filled grooved bearings
• Graphite-filled plug type bearings
• Special alloy bearings
Tolerances
I.D. 3" or less ...................................................................... +.0010"
Over 3" ......................................................................... +.0015"
O.D. 3" or less ........................................................... +.002" to .003"
Over 3" ............................................................. +.003" to .005"
Length .................................................................................... +.005"
Concentricity .............................................................. .003" T.I.R.
3
C93200 Cast Bronze Bearing
Engineering Data
Press Fit
Less than normal press fit proves satisfactory: (1) if the bearing is long
and the wall is not exceptionally thin and (2) if the bearing is also
carrying a moderate load exerted only in one direction.
.005
.004
.003
.002
.001
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
Bearing O.D. (Inches)
Clearance
Greater than normal clearance must be allowed: (1) if exceptionally
high speed is involved or (2) if higher than normal loading is encountered.
.010
.008
.006
.004
.002
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
Shaft Diameter (Inches)
Typical Properties
Note: Not to be used for specification purposes.
Chemical Composition
Copper ........................................................................ 81.0 - 85.0%
Tin .................................................................................... 6.3 - 7.5%
Lead ................................................................................ 6.0 - 8.0%
Zinc ................................................................................. 2.0 - 4.0%
Minimum Physical Properties
Tensile Strength, PSI ............................................................ 35,000
Yield Strength, PSI ................................................................ 20,000
Elongation in 2" ......................................................................... 10%
Brinell @ 500 KG Load ................................................................ 65
Maximum Operating Temperature for C93200 (SAE 660) = 450o F+
Comparable Alloy Specifications: C93200; SAE 660
Common Manufacturing Specifications:
ASTM B505; QQ-C-390B, Type III
4
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB030504 3/16 5/16 1/2 CB071112 7/16 11/16 1- 1/2
CB030506 3/4
CB030508 1 CB071208 7/16 3/4 1
CB071210 1- 1/4
CB040602 1/4 3/8 1/4 CB071212 1- 1/2
CB040603 3/8
CB040604 1/2 CB071312 7/16 13/16 1-1/2
CB040606 3/4
CB040608 1 CB081005 1/2 5/8 5/8
CB040610 1- 1/4 CB081006 3/4
CB081007 7/8
CB040706 1/4 7/16 3/4 CB081008 1
CB040708 1 CB081010 1- 1/4
CB040710 1- 1/4 CB081011 1- 3/8
CB081012 1- 1/2
CB050703 5/16 7/16 3/8 CB081014 1- 3/4
CB050704 1/2 CB081016 2
CB050706 3/4 CB081018 2- 1/4
CB050708 1
CB050710 1- 1/4 CB081106 1/2 11/16 3/4
CB081108 1
CB050806 5/16 1/2 3/4 CB081110 1- 1/4
CB050808 1 CB081112 1- 1/2
CB050810 1- 1/4 CB081114 1- 3/4
CB081116 2
CB060803 3/8 1/2 3/8 CB081118 2- 1/4
CB060804 1/2 CB081120 2- 1/2
CB060806 3/4
CB060808 1 CB081206 1/2 3/4 3/4
CB060810 1- 1/4 CB081208 1
CB060812 1- 1/2 CB081210 1- 1/4
CB081212 1- 1/2
CB060906 3/8 9/16 3/4 CB081214 1- 3/4
CB060908 1 CB081216 2
CB060910 1- 1/4 CB081218 2- 1/4
CB081220 2- 1/2
CB061006 3/8 5/8 3/4 CB081222 2- 3/4
CB061008 1
CB061010 1- 1/4 CB081308 1/2 13/16 1
CB061012 1- 1/2 CB081312 1- 1/2
CB081318 2- 1/4
CB070908 7/16 9/16 1
CB070910 1- 1/4 CB081408 1/2 7/8 1
CB070912 1- 1/2 CB081410 1- 1/4
CB070914 1- 3/4 CB081412 1- 1/2
CB070916 2 CB081414 1- 3/4
CB081416 2
CB071008 7/16 5/8 1
CB071010 1- 1/4 CB081608 1/2 1 1
CB071012 1- 1/2 CB081612 1- 1/2
CB071016 2 CB081616 2
CB081618 2- 1/4
5
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB091108 9/16 11/16 1 CB101412 5/8 7/8 1- 1/2
CB091110 1- 1/4 CB101414 1- 3/4
CB091112 1- 1/2 CB101416 2
CB091114 1- 3/4 CB101418 2- 1/4
CB091116 2 CB101420 2- 1/2
CB091118 2- 1/4 CB101424 3
CB091120 2- 1/2
CB101508 5/8 15/16 1
CB091208 9/16 3/4 1 CB101512 1- 1/2
CB091210 1- 1/4 CB101516 2
CB091212 1- 1/2 CB101520 2- 1/2
CB091214 1- 3/4
CB091216 2 CB101608 5/8 1 1
CB091218 2- 1/4 CB101612 1- 1/2
CB091220 2- 1/2 CB101616 2
CB101618 2- 1/4
CB091308 9/16 13/16 1 CB101620 2- 1/2
CB091310 1- 1/4 CB101624 3
CB091312 1- 1/2
CB091314 1- 3/4 CB101812 5/8 1- 1/8 1- 1/2
CB091316 2 CB101816 2
CB091320 2- 1/2 CB101818 2- 1/4
CB091408 9/16 7/8 1 CB111308 11/16 13/16 1
CB091412 1- 1/2 CB111310 1- 1/4
CB091416 2 CB111312 1- 1/2
CB111314 1- 3/4
CB101204 5/8 3/4 1/2 CB111316 2
CB101206 3/4 CB111320 2- 1/2
CB101208 1
CB101209 1- 1/8 CB111408 11/16 7/8 1
CB101210 1- 1/4 CB111410 1- 1/4
CB101212 1- 1/2 CB111412 1- 1/2
CB101214 1- 3/4 CB111414 1- 3/4
CB101216 2 CB111416 2
CB101218 2- 1/4 CB111418 2- 1/4
CB101220 2- 1/2 CB111420 2- 1/2
CB101224 3
CB111508 11/16 15/16 1
CB101308 5/8 13/16 1 CB111510 1- 1/4
CB101310 1- 1/4 CB111512 1- 1/2
CB101312 1- 1/2 CB111514 1- 3/4
CB101314 1- 3/4 CB111516 2
CB101316 2 CB111520 2- 1/2
CB101318 2- 1/4
CB101320 2- 1/2 CB111610 11/16 1 1- 1/4
CB111618 2- 1/4
CB101404 5/8 7/8 1/2 CB111620 2- 1/2
CB101406 3/4
CB101408 1 CB121406 3/4 7/8 3/4
CB101409 1- 1/8 CB121408 1
CB101410 1- 1/4 CB121410 1- 1/4
6
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB121412 3/4 7/8 1- 1/2 CB122014 3/4 1- 1/4 1- 3/4
CB121414 1- 3/4 CB122016 2
CB121416 2 CB122018 2- 1/4
CB121418 2- 1/4 CB122020 2- 1/2
CB121420 2- 1/2 CB122024 3
7
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB141824 7/8 1- 1/8 3 CB161907 1 1- 3/16 7/8
CB141826 3- 1/4 CB161908 1
CB141828 3- 1/2 CB161910 1- 1/4
CB161912 1- 1/2
CB141908 7/8 1- 3/16 1 CB161914 1- 3/4
CB141910 1- 1/4 CB161916 2
CB141912 1- 1/2 CB161920 2- 1/2
CB141916 2
CB141920 2- 1/2 CB162006 1 1- 1/4 3/4
CB141924 3 CB162008 1
CB162009 1- 1/8
CB142012 7/8 1- 1/4 1- 1/2 CB162010 1- 1/4
CB142014 1- 3/4 CB162011 1- 3/8
CB142016 2 CB162012 1- 1/2
CB142018 2- 1/4 CB162013 1- 5/8
CB142020 2- 1/2 CB162014 1- 3/4
CB142024 3 CB162015 1- 7/8
CB142028 3- 1/2 CB162016 2
CB142032 4 CB162018 2- 1/4
CB162020 2- 1/2
CB142212 7/8 1- 3/8 1- 1/2 CB162022 2- 3/4
CB142214 1- 3/4 CB162024 3
CB142216 2 CB162028 3- 1/2
CB142220 2- 1/2 CB162030 3- 3/4
CB142224 3 CB162032 4
CB162036 4- 1/2
CB151812 15/16 1- 1/8 1- 1/2
CB151816 2 CB162112 1 1- 5/16 1- 1/2
CB151820 2- 1/2 CB162116 2
CB162118 2- 1/4
CB151910 15/16 1- 3/16 1- 1/4 CB162120 2- 1/2
CB151912 1- 1/2 CB162124 3
CB151916 2 CB162128 3- 1/2
CB151918 2- 1/4 CB162130 3- 3/4
CB151924 3
CB162208 1 1- 3/8 1
CB152008 15/16 1- 1/4 1 CB162210 1- 1/4
CB152012 1- 1/2 CB162212 1- 1/2
CB152016 2 CB162214 1- 3/4
CB152020 2- 1/2 CB162216 2
CB152022 2- 3/4 CB162220 2- 1/2
CB162222 2- 3/4
CB152112 15/16 1- 5/16 1- 1/2 CB162224 3
CB152116 2 CB162226 3- 1/4
CB152124 3 CB162228 3- 1/2
CB162232 4
CB161808 1 1- 1/8 1 CB162236 4- 1/2
CB161811 1- 3/8
CB161812 1- 1/2 CB162412 1 1- 1/2 1- 1/2
CB161814 1- 3/4 CB162414 1- 3/4
CB161816 2 CB162416 2
CB161820 2- 1/2 CB162420 2- 1/2
8
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB162424 1 1- 1/2 3 CB182416 1- 1/8 1- 1/2 2
CB162432 4 CB182420 2- 1/2
CB182424 3
CB162616 1 1- 5/8 2 CB182428 3- 1/2
CB162620 2- 1/2 CB182432 4
CB162624 3
CB162628 3- 1/2 CB182614 1- 1/8 1- 5/8 1- 3/4
CB182616 2
CB162852 1 1- 3/4 6- 1/2 CB182620 2- 1/2
CB182624 3
CB163224 1 2 3 CB182628 3- 1/2
CB163252 6- 1/2 CB182632 4
CB182636 4- 1/2
CB172112 1- 1/16 1- 5/16 1- 1/2
CB172116 2 CB183052 1- 1/8 1- 7/8 6- 1/2
CB172120 2- 1/2
CB172124 3 CB183224 1- 1/8 2 3
CB172128 3- 1/2 CB183244 5- 1/2
9
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB202408 1- 1/4 1- 1/2 1 CB203016 1- 1/4 1- 7/8 2
CB202409 1- 1/8 CB203020 2- 1/2
CB202410 1- 1/4 CB203024 3
CB202411 1- 3/8 CB203032 4
CB202412 1- 1/2
CB202413 1- 5/8 CB203224 1- 1/4 2 3
CB202414 1- 3/4 CB203232 4
CB202416 2 CB203252 6- 1/2
CB202418 2- 1/4
CB202420 2- 1/2 CB212414 1- 5/16 1- 1/2 1- 3/4
CB202422 2- 3/4 CB212424 3
CB202424 3
CB202426 3- 1/4 CB212524 1- 5/16 1- 9/16 3
CB202428 3- 1/2 CB212528 3- 1/2
CB202432 4 CB212532 4
CB202434 4- 1/4
CB202436 4- 1/2 CB212616 1- 5/16 1- 5/8 2
CB202440 5 CB212620 2- 1/2
CB202444 5- 1/2 CB212624 3
CB212632 4
CB202516 1- 1/4 1- 9/16 2 CB212638 4- 3/4
CB202520 2- 1/2
CB202524 3 CB212720 1- 5/16 1-11/16 2- 1/2
CB202528 3- 1/2 CB212724 3
CB202530 3- 3/4 CB212732 4
10
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB222832 1- 3/8 1- 3/4 4 CB242808 1- 1/2 1- 3/4 1
CB242810 1- 1/4
CB223024 1- 3/8 1- 7/8 3 CB242812 1- 1/2
CB223028 3- 1/2 CB242814 1- 3/4
CB223032 4 CB242816 2
CB223036 4- 1/2 CB242818 2- 1/4
CB242820 2- 1/2
CB223224 1- 3/8 2 3 CB242824 3
CB223232 4 CB242828 3- 1/2
CB242832 4
CB223452 1- 3/8 2- 1/8 6- 1/2 CB242836 4- 1/2
CB242840 5
CB232614 1- 7/16 1- 5/8 1- 3/4 CB242844 5- 1/2
CB232622 2- 3/4
CB232624 3 CB242924 1- 1/2 1-13/16 3
11
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB263030 1- 5/8 1- 7/8 3- 3/4 CB283422 1- 3/4 2- 1/8 2- 3/4
CB283426 3- 1/4
CB263214 1- 5/8 2 1- 3/4 CB283428 3- 1/2
CB263220 2- 1/2 CB283432 4
CB263224 3 CB283434 4- 1/4
CB263228 3- 1/2 CB283440 5
CB263232 4 CB283444 5- 1/2
CB263236 4- 1/2
CB263240 5 CB283614 1- 3/4 2- 1/4 1- 3/4
CB263244 5- 1/2 CB283616 2
CB283620 2- 1/2
CB263424 1- 5/8 2- 1/8 3 CB283624 3
CB263432 4 CB283628 3- 1/2
CB263436 4- 1/2 CB283632 4
CB263440 5 CB283634 4- 1/4
CB283640 5
CB273124 1-11/16 1-15/16 3
CB273128 3- 1/2 CB283828 1- 3/4 2- 3/8 3- 1/2
CB283836 4- 1/2
CB273228 1-11/16 2 3- 1/2 CB283840 5
CB273236 4- 1/2
CB284052 1- 3/4 2- 1/2 6- 1/2
CB273324 1-11/16 2- 1/16 3
CB273328 3- 1/2 CB293532 1-13/16 2- 3/16 4
CB273332 4 CB293542 5- 1/4
CB273336 4- 1/2
CB273340 5 CB293732 1-13/16 2- 5/16 4
CB273344 5- 1/2 CB293740 5
12
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB313744 1- 15/16 2- 5/16 5- 1/2 CB354232 2- 3/16 2- 5/8 4
CB313750 6- 1/4 CB354240 5
13
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB394740 2- 7/16 2- 15/16 5 CB445232 2- 3/4 3- 1/4 4
CB394750 6- 1/4 CB445240 5
CB445248 6
CB394830 2- 7/16 3 3- 3/4 CB445256 7
CB394840 5
CB394850 6- 1/4 CB445432 2- 3/4 3- 3/8 4
CB445452 6- 1/2
CB404424 2- 1/2 2- 3/4 3
CB404432 4 CB445652 2- 3/4 3- 1/2 6- 1/2
CB404440 5
CB465432 2- 7/8 3- 3/8 4
CB404626 2- 1/2 2- 7/8 3- 1/4 CB465448 6
CB404636 4- 1/2 CB465464 8
14
Cast Bronze
Sleeve (Plane) Bearings
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
CB566448 3- 1/2 4 6 CB687640 4- 1/4 4- 3/4 5
CB566456 7 CB687648 6
CB687656 7
CB566648 3- 1/2 4- 1/8 6
CB688040 4- 1/4 5 5
CB566836 3- 1/2 4- 1/4 4- 1/2 CB688048 6
CB566856 7 CB688056 7
CB566878 9- 3/4
CB728048 4- 1/2 5 6
CB606840 3- 3/4 4- 1/4 5 CB728056 7
CB606856 7 CB728064 8
CB607252 3- 3/4 4- 1/2 6- 1/2 CB728848 4- 1/2 5- 1/2 6
CB728856 7
CB647232 4 4- 1/2 4 CB728864 8
CB647248 6
CB647256 7 CB808848 5 5- 1/2 6
CB808856 7
CB647640 4 4- 3/4 5 CB808864 8
CB647648 6
CB647656 7 CB809656 5 6 7
CB809664 8
CB648040 4 5 5 CB809672 9
CB648048 6
CB648056 7
15
Drilling and Oil Grooving
Standard Bearings
Any of the standard bearings or bar stock listed in this catalog can be
machined, grooved, graphited, drilled or re-machined in many ways to
handle a variety of needs. Such services are available through any of
the Bunting Bearings Authorized Distributors.
Unless otherwise specified, the width and depth of oil grooves will be
proportional to the wall thickness and size of bearing, contained within
the bearing. Special designs or a combination of standard styles,
illustrated below, may be furnished if desired.
In order to form a more perfect oil film between the bearing and shaft,
we recommend a V-shaped groove whenever the design permits, as
it allows full flow of the lubricant across the bearing surface.
Style 2 Style 3
SKR style bearings are available in bore sizes from 5/16" through 3" with
tolerances to meet standard or special applications.
Slightly greater than normal running clearances are also required for
SKR bearings. When it is necessary to finish the bearing at assembly,
total stock removal should not exceed .005". Contact Bunting Bearings
or your local Authorized Distributor for additional information.
17
Bunting C93200 Continuous Cast
and Centrifugal Cast Bronze Bars
Bunting continuous cast bronze bars of C93200 (SAE 660) bronze give
superior quality and performance. Continuous casting achieves a high
density grain structure, free of porosity, resulting in a reduction of tool
wear and component rejects.
Cored and solid bars are stocked in 13" and 105" lengths and are
available in other lengths. When you need a moderate quantity of
special bearings, Bunting bar stock can provide an economical
alternative to expensive tooling. Consider bars for use when you need
special bearings, bearings for prototypes, or for emergency repairs.
Centrifugal cast large diameter cored bars are also available as
standard stock items in 13" lengths.
Contact your local Bunting Bearings Authorized Distributor or
Regional Service Center for more information.
O.D.
LG.
LG.
NOMINAL AVG. AVG. NOMINAL AVG. AVG.
PART WT. WT. PART WT. WT.
NUMBER I.D. O.D. 13" 105" NUMBER I.D. O.D. 13" 105"
BC 408 1/2 1 2.9 24 BC 508 5/8 1 2.5 20
BC 409 1-1/8 3.8 31 BC 509 1-1/8 3.4 28
BC 410 1-1/4 4.8 40 BC 510 1-1/4 4.4 36
BC 412 1-1/2 7.2 59 BC 511 1-3/8 5.5 45
BC 414 1-3/4 9.9 81 BC 516 2 12.7 103
BC 416 2 13.1 107
19
C93200 Continuous Cast
Bronze Cored Bars
20
C93200 Continuous Cast
Bronze Cored Bars
21
C93200 Continuous Cast
Bronze Cored Bars
22
C93200 Continuous Cast
Bronze Cored Bars
23
C93200 Centrifugal Cast
Bronze Cored Bars
24
C93200 Centrifugal Cast
Bronze Cored Bars
25
Bunting C95400 Continuous Cast and
Centrifugal Cast Aluminum Bronze Bars
Bunting Bearings continuous cast aluminum bronze bars are available
from stock in C95400 bronze in standard 13" and 144" lengths solid and
cored bars. Other lengths are available on request.
Aluminum bronze is very hard, very strong, abrasion resistant
bronze whose physical properties remain good at elevated
temperatures—compressive strength at 500o F is the same as that of tin
bronzes at room temperature. Good applications are heavy earth
moving equipment, roll neck bearings, and machine tool bearings.
Centrifugal cast large diameter cored bars are available as standard
stock items in 13" lengths.
Contact your local Bunting Bearings Authorized Distributor or
Regional Service Center for more information or engineering assistance.
O.D.
LG.
NOMINAL AVG. AVG.
PART NOMINAL AVG. AVG.
PART WT. WT. WT. WT.
NUMBER I.D. O.D. 13" 144" NUMBER I.D. O.D. 13" 144"
AB 4 SOLID 1/2 .8 10 AB 32 SOLID 4 46.3 514
AB 6 3/4 1.9 22 AB 34 4-1/4 52.8 586
AB 36 4-1/2 59.3 658
AB 8 SOLID 1 3.1 35
AB 10 1-1/4 4.8 54 AB 40 SOLID 5 72.4 803
AB 12 1-1/2 6.7 75 AB 42 5-1/4 79.5 881
AB 13 1-5/8 7.8 87 AB 44 5-1/2 87.5 970
AB 14 1-3/4 9.1 101 AB 46 5-3/4 96.3 1067
AB 16 SOLID 2 11.9 133
AB 48 SOLID 6 103.5 1147
AB 18 2-1/4 14.8 165
AB 50 6-1/4 111.4 1235
AB 20 2-1/2 18.6 207
AB 52 6-1/2 120.0 1330
AB 22 2-3/4 22.4 249
LG.
NOMINAL AVG. AVG. NOMINAL AVG. AVG.
PART WT. WT. PART WT. WT.
NUMBER I.D. O.D. 13" 144" NUMBER I.D. O.D. 13" 144"
AB 610 3/4 1-1/4 3.5 39 AB1014 1-1/4 1-3/4 5.3 59
AB 612 1-1/2 5.4 61 AB1016 2 7.9 88
AB 614 1-3/4 7.8 87 AB1018 2-1/4 11.3 126
AB 616 2 10.5 117 AB1020 2-1/2 14.9 166
AB1024 3 22.8 253
AB 812 1 1-1/2 4.4 49 AB1028 3-1/2 32.7 363
AB 814 1-3/4 6.7 75
AB 816 2 9.3 104 AB1216 1-1/2 2 6.0 67
AB 818 2-1/4 12.4 138 AB1218 2-1/4 9.1 101
AB 820 2-1/2 16.3 181 AB1220 2-1/2 13.0 145
AB 824 3 24.3 270
27
C95400 Continuous Cast
Aluminum Bronze Cored Bars
PART NOMINAL AVG. AVG. PART
NOMINAL AVG. AVG.
WT. WT. WT. WT.
NUMBER I.D. O.D. 13" 144" NUMBER I.D.O.D. 13" 144"
AB1222 1-1/2 2-3/4 16.8 187 AB2236 2-3/4 4-1/2 40.0 444
AB1224 3 21.0 233
AB1226 3-1/4 26.0 289 AB2428 3 3-1/2 12.9 143
AB1228 3-1/2 30.7 341 AB2430 3-3/4 17.9 199
AB1232 4 41.7 462 AB2432 4 23.4 260
AB1236 4-1/2 53.9 598 AB2434 4-1/4 29.5 327
AB2436 4-1/2 35.8 397
AB1418 1-3/4 2-1/4 7.0 78 AB2440 5 50.1 556
AB1420 2-1/2 10.7 119 AB2444 5-1/2 63.6 705
AB1422 2-3/4 14.7 163 AB2448 6 80.9 897
AB1424 3 18.8 209 AB2456 7 116.0 1286
AB1426 3-1/4 23.2 258
AB1428 3-1/2 28.7 319 AB2632 3-1/4 4 19.0 211
AB1430 3-3/4 34.0 377 AB2634 4-1/4 25.3 281
AB2636 4-1/2 31.4 349
AB1619 2 2-3/8 6.5 73 AB2640 5 44.6 495
AB1620 2-1/2 8.2 92
AB1622 2-3/4 12.1 135 AB2832 3-1/2 4 14.7 163
AB1624 3 16.4 182 AB2834 4-1/4 20.8 231
AB1626 3-1/4 20.7 230 AB2836 4-1/2 26.7 296
AB1628 3-1/2 26.3 292 AB2840 5 40.1 445
AB1630 3-3/4 31.4 349 AB2844 5-1/2 55.6 617
AB1632 4 37.1 412 AB2848 6 71.7 795
AB1636 4-1/2 49.2 546
AB1640 5 62.8 696 AB3038 3-3/4 4-3/4 28.6 317
AB1648 6 93.5 1036
AB3236 4 4-1/2 16.6 184
AB1821 2-1/4 2-5/8 7.2 80 AB3238 4-3/4 23.2 258
AB1822 2-3/4 9.2 103 AB3240 5 29.9 332
AB1824 3 13.5 150 AB3244 5-1/2 45.3 502
AB1826 3-1/4 17.8 198 AB3248 6 61.3 680
AB1828 3-1/2 23.6 262 AB3256 7 97.5 1080
AB3264 8 139.2 1543
AB2024 2-1/2 3 9.9 110
AB2026 3-1/4 14.6 162 AB3440 4-1/4 5 24.6 273
AB2028 3-1/2 20.2 224
AB2030 3-3/4 25.5 283 AB3640 4-1/2 5 18.8 209
AB2032 4 30.9 343 AB3642 5-1/4 25.9 287
AB2036 4-1/2 43.2 479 AB3644 5-1/2 33.9 376
AB2040 5 56.9 631 AB3648 6 49.7 551
AB2048 6 88.8 984 AB3652 6-1/2 68.6 761
AB3660 7-1/2 108.7 1205
AB2226 2-3/4 3-1/4 10.9 121
AB2228 3-1/2 16.4 182 AB4044 5 5-1/2 20.2 224
AB2230 3-3/4 21.6 240 AB4048 6 36.9 409
AB2232 4 27.7 307 AB4056 7 73.2 812
AB2234 4-1/4 33.8 375
28
C95400 Continuous Cast
Aluminum Bronze Cored Bars
NOMINAL AVG. AVG. NOMINAL AVG. AVG.
PART WT. WT. PART WT. WT.
NUMBER I.D. O.D. 13" 144" NUMBER I.D. O.D. 13" 144"
AB4064 5 8 115.2 1277 AB4864 6 8 85.6 949
AB4452 5-1/2 6-1/2 40.4 448 AB5260 6-1/2 7-1/2 47.3 525
29
C95400 Centrifugal Cast
Aluminum Bronze Cored Bars
PART NOMINAL AVG. PART NOMINAL AVG.
WT. WT.
NUMBER I.D. O.D. 13" NUMBER I.D. O.D. 13"
AB64072 8 9 60 AB80144 10 18 641
AB64076 9-1/2 85
AB64080 10 112 AB84092 10-1/2 11-1/2 76
AB64084 10-1/2 141 AB84096 12 109
AB64088 11 171 AB84100 12-1/2 144
AB64092 11-1/2 203 AB84104 13 179
AB64096 12 236 AB84108 13-1/2 216
AB64100 12-1/2 270 AB84112 14 255
AB64104 13 306 AB84116 14-1/2 295
AB64108 13-1/2 343 AB84120 15 336
AB64112 14 381
AB64128 16 549 AB88096 11 12 80
AB88100 12-1/2 114
AB68076 8-1/2 9-1/2 62 AB88104 13 150
AB68080 10 90 AB88108 13-1/2 187
AB68084 10-1/2 119 AB88112 14 225
AB68088 11 149 AB88116 14-1/2 265
AB68092 11-1/2 180 AB88120 15 306
AB68096 12 213
AB68100 12-1/2 247 AB92100 11-1/2 12-1/2 83
AB68104 13 283 AB92104 13 119
AB68108 13-1/2 320 AB92108 13-1/2 156
AB68112 14 359 AB92112 14 195
AB92116 14-1/2 234
AB72080 9 10 67 AB92120 15 276
AB72084 10-1/2 95
AB72088 11 125 AB96104 12 13 87
AB72092 11-1/2 156 AB96108 13-1/2 124
AB72096 12 189 AB96112 14 162
AB72100 12-1/2 224 AB96116 14-1/2 202
AB72104 13 259 AB96120 15 243
AB72108 13-1/2 296 AB96124 15-1/2 286
AB72112 14 335 AB96128 16 330
AB96144 18 520
AB76084 9-1/2 10-1/2 69
AB76088 11 100 AB100108 12-1/2 13-1/2 90
AB76092 11-1/2 131 AB100112 14 129
AB76096 12 164 AB100116 14-1/2 168
AB76100 12-1/2 198 AB100120 15 210
AB76104 13 234 AB100124 15-1/2 252
AB76108 13-1/2 271 AB100128 16 296
AB76112 14 310
AB104112 13 14 94
AB80088 10 11 73 AB104116 14-1/2 133
AB80092 11-1/2 104 AB104120 15 175
AB80096 12 137 AB104124 15-1/2 217
AB80100 12-1/2 172 AB104128 16 261
AB80104 13 207
AB80108 13-1/2 244 AB108116 13-1/2 14-1/2 97
AB80112 14 283 AB108120 15 138
AB80128 16 451 AB108124 15-1/2 181
30
C95400 Centrifugal Cast
Aluminum Bronze Cored Bars
NOMINAL AVG. NOMINAL AVG.
PART WT. PART WT.
NUMBER I.D. O.D. 13" NUMBER I.D. O.D. 13"
AB108128 13-1/2 16 225 AB128136 16 17 114
AB108132 16-1/2 270 AB128140 17-1/2 163
AB108136 17 317 AB128144 18 212
AB128148 18-1/2 263
AB112120 14 15 100 AB128152 19 315
AB112144 18 377
AB112124 15-1/2 143 AB132140 16-1/2 17-1/2 118
AB112128 16 187 AB132144 18 167
AB112132 16-1/2 233 AB132148 18-1/2 218
AB112136 17 279 AB132152 19 271
AB112144 18 377 AB132156 19-1/2 324
31
C95400 Continuous Cast Aluminum
Bronze Wearplate
Engineering Data
Typical Properties - C95400
Note: Not to be used for specification purposes.
Chemical Composition
Aluminum ..................................................................... 10.0 - 11.5%
Iron ................................................................................... 3.0 - 5.0%
Copper ................................................................................ Balance
C95400 Wearplate
Dimensional Tolerances
32
C95400 Continuous Cast
Aluminum Bronze Wearplate
Products
Proprietary, high performance "Dri-Plane" for dry
lubrication and/or high temperature applications.
BB-16 for heavy load applications.
Structural parts: lugs, shifter forks, gears, etc.
Plane, thrust and flange bearings.
Bronze bars and circular bronze discs.
Benefits
Self-lubricating, oil filled powdered metal products.
Manufactured to standard ASTM specifications.
Temperatures ranging from 10oF to 700oF.
Multi-cavity tools lower your cost.
In-house tooling capability.
Sample Industries
Household appliances
Off-highway equipment
Agricultural equipment
Food processing
Aerospace
34
Bunting Dri-Plane®
Bearings
Bunting Bearings offers a high performance sintered bearing called
"Dri-Plane" using a proprietary metal compound for dry lubrication and/
or high temperature applications.
Benefits
Applications
• Food processing
• Electrical equipment
• Pharmaceuticals
• Furnaces and ovens
• Aerospace
• Vacuum processes
• Glass manufacturing
35
Bunting BB-16®
Bearings
Bunting BB-16 is a self-lubricating, powdered metal bearing material
typically used for heavily loaded applications. This bearing material
has excellent compressive strength, wearability and is shock resistant.
Typical Uses
• Off-road equipment
• Backhoes, graders, and earth-moving equipment
• Escalators
• Automotive and railroad applications
• Heavily loaded applications
36
Bunting Powdered Metal
Structural Parts
37
Bunting Oil-Filled P/M
Bronze Bearings
Stock Bearings
Bunting Bearings offers a complete line of stock plane bearings,
flange bearings and washers made of P/M bronze. Bunting sintered
bronze stock bearings have long conformed to ASTM chemical and
physical properties, and are the first to include all ASTM standard
sizes to ASTM recommended dimensions and tolerances.
After forming, sintering and sizing, the bearings are vacuum
impregnated with SAE 30 oil that provides lubricant which is
metered from the bearing to the shaft during rotation.
Standard off-the-shelf oil impregnated bronze bearings should
function satisfactorily in temperatures ranging from 10oF to 220oF.
Consult Bunting if application requires higher temperatures or other
specific operating conditions.
38
Flange Bearings I.D. or O.D. same as Plane Bearings
Flange Flg. O.D. Flange Flg. Thickness
O.D. size Tolerance O.D. size Tolerance
0 to 1.5 +0.005 0 to 1.5 +0.005
Over 1.5 to 3 +0.010 Over 1.5 to 3 +0.010
Over 3 to 6 +0.025 Over 3 to 6 +0.015
Flange thickness tolerance depends on O.D. of flange.
CONCENTRICITY TOLERANCE
O.D., In., Wall Thickness Concentricity
Maximum, In. Tolerance, In., TIR
Up to 1.010 Up to 0.255 0.003
1.011 to 1.510 Up to 0.355 0.003
1.511 to 2.010 Up to 0.505 0.004
2.011 to 3.010 Up to 0.760 0.005
3.011 to 4.010 Up to 1.010 0.005
4.011 to 5.010 Up to 1.510 0.006
5.011 to 6.010 Up to 2.010 0.007
Housing Chamfers
Smooth housing bore chamfers reduce bearing installation time and
eliminate press fit loss due to the shearing of metal from the bearing
O.D.
Tooling for production of stamped housings should be designed
to provide a radius edge which will act as a lead and furnish
clearance for flange fillet.
Standard Housing Chamfers
Bore Diameter Chamfer Size
Up to .500" 1/32" x 45o
.500" to 1.000" 3/64" x 45o
1.000" to 2.000" 1/16" x 45o
2.000" to 3.000" 5/64" x 45o
3.000" to 4.000" 3/32" x 45o
39
Flange Fillets
A fillet at the body O.D. of a flange bearing facilitates manufacturing
and strengthens the part.
Running Clearance
Proper running clearance for bearings depends to a great extent on
the particular application. Only minimum recommended clearances
for oil impregnated bearings used with ground steel shafting are
listed in the Running Clearances Table.
Storage
Oil-impregnated units should be stored in suitable containers using
plastic bags, waxpaper, metal, glass, etc. Wood, ordinary paper
and cardboard are not suitable since they absorb oil from the
bearing. Properly stored and protected against dust, oil-impregnated
bearings retain their oil supply.
40
Typical Properties*
Materials SAE 841 SAE 863
Properties Bronze
COMPOSITION-PERCENT
Copper 87.5-90.5 18.0-22.0
Iron 1.0 max. Balance
Lead -- --
Carbon 1.75 max. --
Tin 9.5-10.5 --
Acid Insolubles (max.) -- --
Magnesium -- --
Total Other Elements (max.) 0.5 2.0
Balance -- --
PHYSICAL AND
MECHANICAL PROPERTIES
Density (gm per cu. cm.) 6.4-6.8 5.8-6.2
Porosity (% Oil by vol.) 19 min. 19 min.
"K" Strength Constant 26,500 30,000
Tensile Strength (PSI) 14,000 22,000
Elongation (% in one inch) 1 1
Yield Strength in Comp. (psi)** 11,000 22,000
COMPARABLE
SPECIFICATIONS
ASTM B438 B439
Grade 1 Grade 4
Type II
Military BEARINGS:
MIL-B-5687D MIL-B-5687D
Type I Type II
Grade 1 Grade 4
FORMERLY: FORMERLY:
MIL-B-5687C MIL-B-5687C
Type I Type II
Comp. A Comp. B
BAR:
FORMERLY:
MIL-C-50709
Grade 1
Type II
MPIF CT-1000-K26 --
FORMERLY:
CT-0010-R
*Bearings may exhibit appreciable differences in properties due to size, shape,
thickness, etc.
**For .001" permanent set on test specimens 1-1/4" diameter x 1" long.
41
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
1/8 X 3/16 NOMINAL 3/16 X 1/4 NOMINAL
EP020304 .1270 .1905 1/4 EP030404 .1895 .2530 1/4
(P12-2) (P18-2)
EP020308 1/2 EP030406 3/8
(P12-4) (P18-3)
EP030408 1/2
AA101-8 .1250 .1900 5/32 (P18-4)
AA101-2 1/4 EP030410 5/8
AA101 3/8
AA101-1 1/2 (P18-5)
EP030412 3/4
AA110-1 .1265 .1895 1/8 (P18-6)
AA110-2 1/4
AA110-4 5/16 AA225-2 .1875 .2520 1/4
1/8 X 7/32 NOMINAL AA225-1 5/16
AA225-6 3/8
AA223 .1270 .2220 1/4 AA225-4 1/2
AA223-1 3/8 AA225-3 5/8
1/8 X 1/4 NOMINAL AA226-1 .1885 .2520 1/4
EP020402 .1270 .2530 1/8 AA226-2 3/8
(P13-1) AA226 7/16
EP020404 1/4 AA226-3 1/2
(P13-2) AA226-4 5/8
EP020406 3/8 3/16 X 5/16 NOMINAL
(P13-3)
EP030503 .1895 .3155 3/16
EP020408 1/2 (P19-1.5)
(P13-4)
EP030504 1/4
(P19-2)
AA224 .1280 .2530 1/4
AA224-1 3/8 EP030505 5/16
(P19-2.5)
1/8 X 3/8 NOMINAL EP030506 3/8
AA337-2 .1270 .3770 1/4 (P19-3)
AA337-3 1/2 EP030508 1/2
(P19-4)
5/32 X 7/32 NOMINAL
EP030510 5/8
AA211 .1560 .2200 1/4 (P19-5)
AA211-1 3/8
EP030512 3/4
5/32 X 1/4 NOMINAL (P19-6)
AA204-1 .1590 .2530 1/4 EP030516 1
AA204 5/16 (P19-8)
AA238 .1565 .2525 3/8 AA309-9 .1885 .3145 3/16
42
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA309 .1885 .3145 1/4 EP040508 .2520 .3155 1/2
AA309-3 5/16 (P25-4)
AA309-4 3/8 EP040510 5/8
AA309-8 7/16
AA309-14 1/2 (P25-5)
AA309-7 5/8 EP040512 3/4
AA309-5 3/4 (P25-6)
43
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA304-11 .2505 .3770 1- 1/4 EP040812 .2520 .5030 3/4
(P28-6)
AA307 .2520 .3770 1/4 EP040816 1
AA307-1 5/16 (P28-8)
AA307-9 3/8
AA307-3 1/2 EP040820 1- 1/4
AA307-10 5/8 (P28-10)
AA307-11 3/4
AA307-2 1 AAB519-4 .2520 .5015 5/16
AA307-13 1- 1/8 AAB519-1 1/2
AAB519-2 3/4
AA385-1 .2530 .3770 1/4 AAB519-3 1
AA385 1/2
AA385-2 3/4 5/16 X 3/8 NOMINAL
1/4 X 7/16 NOMINAL EP050604 .3145 .3780 1/4
(P31-2)
EP040706 .2520 .4405 3/8
(P27-3) EP050606 3/8
(P31-3)
EP040708 1/2
(P27-4) EP050608 1/2
(P31-4)
EP040710 5/8
(P27-5) EP050610 5/8
(P31-5)
EP040712 3/4
(P27-6) EP050612 3/4
(P31-6)
EP040714 7/8
(P27-7) EP050614 7/8
(P31-7)
EP040716 1
(P27-8) EP050616 1
(P31-8)
AA412-10 .2520 .4395 3/8
AA412-7 1/2 AA306-11 .3135 .3770 1/4
AA412-6 5/8 AA306-1 5/16
AA412-1 3/4 AA306-3 3/8
AA412-8 1 AA306-7 1/2
AA306-8 5/8
AA430 .2510 .4395 3/8 AA306-6 3/4
AA430-1 1/2 5/16 X 7/16 NOMINAL
AA430-5 5/8
AA430-2 3/4 AA403 .3115 .4410 3/8
AA430-6 7/8 AA403-2 1/2
AA430-3 1
1/4 X 1/2 NOMINAL EP050704 .3145 .4405 1/4
(P32-2)
EP040805 .2520 .5030 5/16
(P28-2.5) EP050705 5/16
(P32-2.5)
EP040808 1/2
(P28-4) EP050706 3/8
(P32-3)
44
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP050708 .3145 .4405 1/2 EP050806 .3145 .5030 3/8
(P32-4) (P33-3)
EP050710 5/8 EP050808 1/2
(P32-5) (P33-4)
EP050712 3/4 EP050810 5/8
(P32-6) (P33-5)
EP050714 7/8 EP050812 3/4
(P32-7) (P33-6)
EP050716 1 EP050814 7/8
(P32-8) (P33-7)
EP050718 1- 1/8 EP050816 1
(P32-9) (P33-8)
EP050720 1- 1/4 EP050820 1- 1/4
(P32-10) (P33-10)
EP050824 1- 1/2
AA407-1 .3125 .4400 1/4 (P33-12)
AA407-10 5/16
AA407-7 3/8 AA520-8 .3125 .5030 3/8
AA407-3 1/2 AA520-3 1/2
AA407-2 5/8 AA520-4 5/8
AA407-4 3/4 AA520-1 3/4
AA520-2 7/8
AA401-17 .3135 .4395 1/4 AA520-5 1
AA401-25 5/16
AA401-2 3/8 3/8 X 7/16 NOMINAL
AA401-20 7/16
AA401-3 1/2 EP060708 .3770 .4405 1/2
AA401-21 5/8 (P37-4)
AA401-11 11/16 EP060710 5/8
AA401-5 3/4 (P37-5)
AA401-12 7/8
AA401-1 1 EP060712 3/4
AA401 1- 1/8 (P37-6)
AA401-6 1- 1/4 EP060716 1
AA401-8 1- 3/8 (P37-8)
AA417-7 .3155 .4395 1/4 AA432-4 .3765 .4400 1/4
AA417 1/2 AA432-2 3/8
AA417-3 3/4 AA432-1 1/2
5/16 X 1/2 NOMINAL AA432-3 3/4
AA506-16 .3140 .5030 1/4 3/8 X 1/2 NOMINAL
AA506-2 3/8 AA507-12 .3765 .5030 3/16
AA506-7 1/2 AA507-19 1/4
AA506-1 9/16 AA507-13 5/16
AA506-3 5/8 AA507-11 3/8
AA506-8 3/4 AA507-4 7/16
AA506-9 1 AA507-10 1/2
45
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA507-5 .3765 .5030 5/8 3/8 X 9/16 NOMINAL
AA507-2 3/4
AA507-3 7/8 AA516-5 .3765 .5655 3/8
AA507-23 1 AA516-6 1/2
AA507-17 1- 1/8 AA516-3 9/16
AA516 11/16
AA521-4 .3750 .5030 1/4 AA516-10 3/4
AA521-9 3/8 AA516-8 1
AA521-8 7/16 AA516-2 1- 1/4
AA521-1 1/2
AA521-10 5/8 EP060906 .3770 .5655 3/8
AA521 3/4 (P39-3)
AA521-2 7/8 EP060908 1/2
AA521-11 1 (P39-4)
AA521-12 1- 1/4
EP060910 5/8
EP060803 .3770 .5030 3/16 (P39-5)
(P38-1.5) EP060912 3/4
EP060804 1/4 (P39-6)
(P38-2) EP060914 7/8
EP060805 5/16 (P39-7)
(P38-2.5) EP060916 1
EP060806 3/8 (P39-8)
(P38-3) EP060920 1- 1/4
EP060807 7/16 (P39-10)
(P38-3.5) 3/8 X 5/8 NOMINAL
EP060808 1/2
(P38-4) EP061006 .3770 .6280 3/8
EP060810 5/8 (P40-3)
(P38-5) EP061008 1/2
EP060812 3/4 (P40-4)
(P38-6) EP061010 5/8
EP060814 7/8 (P40-5)
(P38-7) EP061012 3/4
EP060816 1 (P40-6)
(P38-8) EP061014 7/8
EP060818 1- 1/8 (P40-7)
(P38-9) EP061016 1
EP060820 1- 1/4 (P40-8)
(P38-10) EP061020 1- 1/4
(P40-10)
AAB502-5 .3780 .5025 1/4
AAB502 1/2 AA630-8 .3760 .6270 3/8
AAB502-3 5/8 AA630-16 7/16
AAB502-1 3/4 AA630-11 1/2
AAB502-2 1 AA630-6 5/8
AA630-12 3/4
46
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA630 .3760 .6270 7/8 AA515-8 .4390 .5650 1
AA630-7 1
AA630-1 1- 1/8 7/16 X 5/8 NOMINAL
AA630-2 1- 1/4 EP071006 .4395 .6280 3/8
3/8 X 11/16 NOMINAL (P44-3)
EP071008 1/2
AA615 .3765 .6890 3/4 (P44-4)
AA615-2 1- 1/2
EP071010 5/8
3/8 X 3/4 NOMINAL (P44-5)
EP061206 .3770 .7530 3/8 EP071012 3/4
(P41-3) (P44-6)
EP061208 1/2 EP071014 7/8
(P41-4) (P44-7)
EP061212 3/4 EP071016 1
(P41-6) (P44-8)
EP061216 1 EP071020 1- 1/4
(P41-8) (P44-10)
EP061220 1- 1/4 EP071024 1- 1/2
(P41-10) (P44-12)
47
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA628-10 .5015 .6280 1/2 EP081110 .5020 .6905 5/8
AA628-3 9/16 (P51-5)
AA628-25 5/8 EP081112 3/4
AA628-12 11/16
AA628-6 3/4 (P51-6)
AA628-20 7/8 EP081114 7/8
AA628 1 (P51-7)
AA628-11 1- 1/4 EP081116 1
AA628-5 1- 1/2 (P51-8)
EP081005 .5020 .6280 5/16 EP081118 1- 1/8
(P50-2.5) (P51-9)
EP081006 3/8 EP081120 1- 1/4
(P50-3) (P51-10)
EP081007 7/16 EP081124 1- 1/2
(P50-3.5) (P51-12)
EP081008 1/2
(P50-4) AA618-16 .5040 .6900 1/4
EP081009 9/16 AA618-1 1/2
AA618-13 9/16
(P50-4.5) AA618-12 5/8
EP081010 5/8 AA618-11 3/4
(P50-5) AA618-8 7/8
EP081011 11/16 AA618-6 1
(P50-5.5) AA618-2 1- 1/8
AA618-5 1- 3/8
EP081012 3/4
(P50-6) AA650-4 .5015 .6900 3/8
EP081014 7/8 AA650-1 1/2
(P50-7) AA650-6 9/16
EP081016 1 AA650-9 5/8
AA650 3/4
(P50-8) AA650-7 7/8
EP081018 1- 1/8 AA650-2 1
(P50-9) AA650-5 1- 1/8
EP081020 1- 1/4 AA650-12 1- 1/4
(P50-10) AA650-3 1- 1/2
EP081024 1- 1/2 AA631-13 .5025 .6890 3/8
(P50-12) AA631 3/4
AA631-1 1- 1/4
AA634-4 .5040 .6275 1/2
AA634-5 1 1/2 X 3/4 NOMINAL
48
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP081206 .5020 .7530 3/8 AA886-3 .5010 .8150 3/4
(P52-3) AA886-1 1
EP081208 1/2 AA886-4 1- 1/2
(P52-4) 1/2 X 7/8 NOMINAL
EP081210 5/8
(P52-5) EP081408 .5020 .8790 1/2
EP081212 3/4 (P54-4)
(P52-6) EP081410 5/8
EP081214 7/8 (P54-5)
(P52-7) EP081412 3/4
EP081216 1 (P54-6)
(P52-8) EP081414 7/8
EP081218 1- 1/8 (P54-7)
(P52-9) EP081416 1
EP081220 1- 1/4 (P54-8)
(P52-10) EP081420 1- 1/4
EP081224 1- 1/2 (P54-10)
(P52-12) EP081424 1- 1/2
EP081228 1- 3/4 (P54-12)
(P52-14)
AA842-7 .5030 .8790 1/2
EP081232 2 AA842-4 3/4
(P52-16) AA842-3 1
AA842-2 1- 1/4
AA742-1 .5005 .7520 1/2 AA842 1- 1/2
AA742-2 3/4
AA742 1 1/2 X 1 NOMINAL
AA742-4 1- 1/8 EP081612 .5020 1.0040 3/4
AA742-3 1- 1/4 (P55-6)
EP081616 1
AA753 .5015 .7520 1/2
AA753-1 9/16 (P55-8)
AA753-5 3/4 EP081624 1- 1/2
AA753-2 1 (P55-12)
AA753-4 1- 1/2 EP081632 2
1/2 X 13/16 NOMINAL (P55-16)
49
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP091110 .5645 .6905 5/8 EP091316 .5645 .8165 1
(P56-5) (P58-8)
EP091112 3/4 EP091320 1- 1/4
(P56-6) (P58-10)
EP091116 1 EP091324 1- 1/2
(P56-8) (P58-12)
EP091120 1- 1/4
(P56-10) AA807-3 .5630 .8150 3/4
AA807-2 1
EP091124 1- 1/2 AA807-4 1- 1/4
(P56-12)
9/16 X 7/8 NOMINAL
9/16 X 3/4 NOMINAL
AA863-3 .5670 .8770 1
AA711-6 .5635 .7535 5/8 AA863 1- 3/8
AA711-1 3/4 5/8 X 3/4 NOMINAL
AA711-3 1
AA710-13 .6270 .7530 3/8
AA711-5 1- 1/4 AA710-27 1/2
AA711 1- 3/8 AA710-19 5/8
AA711-2 1- 1/2 AA710-6 3/4
AA710-16 7/8
AA709-7 .5660 .7530 1/2 AA710-3 1
AA709-8 3/4 AA710-8 1- 1/8
AA710-5 1- 1/4
AA709 1 AA710-4 1- 1/2
AA709-5 1- 1/4
AA709-6 1- 1/2 AA724-8 .6260 .7530 1/2
AA724-2 7/8
EP091208 .5645 .7530 1/2 AA724-3 1
(P57-4) AA724 1- 1/8
AA724-5 1- 1/4
EP091212 3/4
(P57-6) EP101206 .6270 .7530 3/8
EP091216 1 (P62-3)
(P57-8) EP101208 1/2
EP091220 1- 1/4 (P62-4)
(P57-10) EP101210 5/8
EP091224 1- 1/2 (P62-5)
(P57-12) EP101212 3/4
9/16 X 13/16 NOMINAL (P62-6)
EP101214 7/8
EP091308 .5645 .8165 1/2 (P62-7)
(P58-4) EP101216 1
EP091312 3/4 (P62-8)
(P58-6) EP101218 1- 1/8
(P62-9)
50
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP101220 .6270 .7530 1- 1/4 5/8 X 7/8 NOMINAL
(P62-10)
EP101408 .6270 .8790 1/2
EP101224 1- 1/2
(P64-4)
(P62-12)
EP101410 5/8
AA741 .6270 .7520 1/2 (P64-5)
AA741-1 5/8 EP101412 3/4
AA741-4 3/4 (P64-6)
EP101414 7/8
5/8 X 13/16 NOMINAL
(P64-7)
EP101308 .6270 .8165 1/2 EP101416 1
(P63-4) (P64-8)
EP101310 5/8 EP101418 1- 1/8
(P63-5) (P64-9)
EP101312 3/4 EP101420 1- 1/4
(P63-6) (P64-10)
EP101314 7/8 EP101424 1- 1/2
(P63-7) (P64-12)
EP101316 1 EP101428 1- 3/4
(P63-8) (P64-14)
EP101320 1- 1/4 EP101432 2
(P63-10) (P64-16)
EP101324 1- 1/2
(P63-12) AA832-11 .6270 .8780 1/2
EP101328 1- 3/4 AA832-12 5/8
(P63-14) AA832-6 3/4
AA832-8 7/8
AA832-1 1
AA814-3 .6280 .8155 5/8 AA832-13 1- 1/8
AA814-2 3/4 AA832-4 1- 1/4
AA814 1 AA832-2 1- 3/8
AA814-5 1- 1/4 AA832-5 1- 1/2
AA832-9 1- 5/8
AA810-4 .6250 .8150 1/2 AA832-18 2
AA810-2 5/8
AA810-10 3/4 AA880-4 .6250 .8770 1/2
AA810-1 7/8 AA880-2 3/4
AA810-7 1 AA880-1 1
AA810-11 1- 1/4 AA880 1- 1/2
AA810 1- 3/8
AA810-12 1- 1/2 5/8 X 15/16 NOMINAL
AA811-7 .6270 .8150 3/4 EP101510 .6270 .9415 5/8
AA811-6 1 (P65-5)
AA811-2 1- 1/4 EP101512 3/4
AA811-5 1- 3/8 (P65-6)
AA811-3 1- 1/2 EP101516 1
AA811-1 1- 3/4
AA811 2 (P65-8)
51
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA946-4 .6280 .9400 5/8 EP111432 .6895 .8790 2
AA946-2 3/4 (P68-16)
AA946-1 1
5/8 X 1 NOMINAL AA851-2 .6900 .8780 1/2
AA851-7 3/4
EP101608 .6270 1.0040 1/2 AA851-8 1
(P66-4) AA851-6 1- 1/8
AA851-1 1- 1/4
EP101610 5/8
(P66-5) 11/16 X 15/16 NOMINAL
EP101612 3/4 AA939-3 .6890 .9410 1
(P66-6) AA939-2 1- 1/4
EP101616 1 AA939-4 1- 1/2
(P66-8) 3/4 X 7/8 NOMINAL
EP101620 1- 1/4
(P66-10) EP121408 .7520 .8790 1/2
(P75-4)
EP101624 1- 1/2
(P66-12) EP121409 9/16
(P75-4.5)
EP101628 1- 3/4
(P66-14) EP121410 5/8
(P75-5)
EP101632 2
(P66-16) EP121411 11/16
(P75-5.5)
AA1011-12 .6280 1.0035 3/4 EP121412 3/4
AA1011-5 7/8 (P75-6)
AA1011-3 1 EP121414 7/8
AA1011-4 1- 1/8 (P75-7)
AA1011-1 1- 1/4
AA1011-13 1- 3/8 EP121416 1
AA1011 1- 1/2 (P75-8)
EP121418 1- 1/8
11/16 X 13/16 NOMINAL (P75-9)
AA812-1 .6885 .8150 1 EP121420 1- 1/4
AA812 1- 1/4 (P75-10)
11/16 X 7/8 NOMINAL EP121424 1- 1/2
(P75-12)
EP111412 .6895 .8790 3/4
(P68-6) EP121426 1- 5/8
(P75-13)
EP111416 1
(P68-8)
AA838-9 .7510 .8780 9/16
EP111420 1- 1/4 AA838-25 5/8
(P68-10) AA838-16 3/4
EP111424 1- 1/2 AA838-6 7/8
(P68-12) AA838-7 1
EP111428 1- 3/4 AA838-13 1- 1/8
AA838-5 1- 1/4
(P68-14) AA838-15 1- 3/8
AA838-4 1- 1/2
52
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA838-8 .7510 .8780 1- 5/8 AA921 .7515 .9400 1- 3/4
AA921-6 2
AA839-1 .7530 .8780 5/8
AA839-3 11/16 3/4 X 1 NOMINAL
AA839-6 3/4 EP121608 .7520 1.0040 1/2
AA839-13 1 (P77-4)
AA839-2 1- 1/8 EP121610 5/8
AA839-4 1- 1/4
AA839-7 1- 1/2 (P77-5)
EP121612 3/4
AA885 .7520 .8780 3/4 (P77-6)
AA885-3 1 EP121614 7/8
AA885-4 1- 1/4 (P77-7)
3/4 X 15/16 NOMINAL EP121616 1
AA912 .7520 .9420 1 (P77-8)
AA912-4 1- 1/4 EP121618 1- 1/8
AA912-1 1- 3/8 (P77-9)
AA912-6 1- 1/2 EP121620 1- 1/4
AA912-2 1- 5/8 (P77-10)
AA912-7 1- 3/4
EP121624 1- 1/2
EP121508 .7520 .9415 1/2 (P77-12)
(P76-4) EP121628 1- 3/4
EP121510 5/8 (P77-14)
(P76-5) EP121632 2
EP121512 3/4 (P77-16)
(P76-6) EP121640 2- 1/2
EP121514 7/8 (P77-20)
(P76-7)
AA1043-6 .7530 1.0030 3/4
EP121516 1 AA1043-8 7/8
(P76-8) AA1043-9 1
EP121518 1- 1/8 AA1043 1- 1/4
(P76-9) AA1043-4 1- 1/2
EP121520 1- 1/4
AA1005-5 .7505 1.0025 3/4
(P76-10) AA1005-7 1
EP121524 1- 1/2 AA1005-3 1- 1/8
(P76-12) AA1005-2 1- 1/4
EP121528 1- 3/4 AA1005-4 1- 1/2
(P76-14)
AA1049-18 .7520 1.0025 3/8
EP121532 2 AA1049-14 1/2
(P76-16) AA1049-1 3/4
AA1049-2 7/8
AA921-5 .7515 .9400 3/4 AA1049-3 1
AA921-4 1 AA1049-16 1- 1/8
AA921-2 1- 1/8 AA1049 1- 1/4
AA921-3 1- 1/4 AA1049-17 1- 3/8
AA921-1 1- 1/2 AA1049-4 1- 1/2
53
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA1049-9 .7520 1.0025 1- 3/4 AA1257 .7530 1.2530 1
AA1049-5 2 AA1257-1 1- 1/4
AA1049-11 2- 1/8 AA1257-2 1- 1/2
AA1049-12 2- 1/4
AA1049-6 2- 1/2 13/16 X 1 NOMINAL
54
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA1009-2 .8770 1.0030 1- 1/4 AA1108-6 .8760 1.1280 2- 3/4
7/8 X 1- 1/16 NOMINAL AA1104-2 .8780 1.1275 1
EP141716 .8770 1.0665 1 AA1104-5 1- 1/4
(P88-8) AA1104-4 1- 3/8
AA1104-3 1- 1/2
EP141720 1- 1/4
(P88-10) 7/8 X 1- 1/4 NOMINAL
EP142012 .8770 1.2540 3/4
AA1051-3 .8770 1.0650 3/4 (P90-6)
AA1051-2 1- 1/4 EP142016 1
7/8 X 1- 1/8 NOMINAL (P90-8)
EP142020 1- 1/4
EP141812 .8770 1.1290 3/4 (P90-10)
(P89-6) EP142024 1- 1/2
EP141814 7/8 (P90-12)
(P89-7) EP142032 2
EP141816 1 (P90-16)
(P89-8)
EP141818 1- 1/8 AA1242-2 .8780 1.2530 3/4
(P89-9) AA1242-3 1
EP141820 1- 1/4 AA1242 1- 3/8
(P89-10)
AA1203-3 .8770 1.2520 1
EP141822 1- 3/8 AA1203 1- 1/4
(P89-11) AA1203-1 1- 1/2
EP141824 1- 1/2
(P89-12) 15/16 X 1- 1/16 NOMINAL
EP141828 1- 3/4 AA1087-1 .9400 1.0650 3/4
(P89-14) AA1087 1- 1/4
EP141832 2 15/16 X 1- 3/16 NOMINAL
(P89-16) EP151912 .9395 1.1915 3/4
EP141836 2- 1/4 (P93-6)
(P89-18) EP151916 1
EP141840 2- 1/2 (P93-8)
(P89-20) EP151920 1- 1/4
(P93-10)
AA1108 .8760 1.1280 3/4
AA1108-15 7/8 EP151924 1- 1/2
AA1108-1 1 (P93-12)
AA1108-2 1- 1/8 EP151932 2
AA1108-7 1- 1/4 (P93-16)
AA1108-16 1- 3/8
AA1108-12 1- 1/2 AA1118-6 .9390 1.1895 7/8
AA1108-10 1- 3/4 AA1118-4 1
AA1108-3 2 AA1118-2 1- 1/4
AA1108-11 2- 1/4 AA1118-5 1- 1/2
AA1108-5 2- 1/2
55
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
15/16 X 1- 1/4 NOMINAL AA1156 1.0035 1.1280 3/4
AA1156-4 7/8
AA1216-3 .9400 1.2540 1- 1/2 AA1156-3 1- 1/4
AA1216 2 AA1156-1 1- 1/2
EP152012 .9395 1.2540 3/4 1 X 1- 3/16 NOMINAL
(P94-6)
EP161912 1.0030 1.1915 3/4
EP152016 1 (P101-6)
(P94-8) EP161916 1
EP152020 1- 1/4 (P101-8)
(P94-10) EP161920 1- 1/4
EP152024 1- 1/2 (P101-10)
(P94-12) EP161924 1- 1/2
EP152028 1- 3/4 (P101-12)
(P94-14) EP161928 1- 3/4
EP152032 2 (P101-14)
(P94-16) EP161932 2
(P101-16)
AA1206-1 .9375 1.2530 1
AA1206-4 1- 1/4 AA1154-2 1.0020 1.1895 3/4
AA1206-2 1- 1/2 AA1154-1 1
1 X 1- 1/8 NOMINAL AA1154-3 1- 1/2
AA1154 2
EP161812 1.0030 1.1290 3/4
(P100-6) 1 X 1- 1/4 NOMINAL
EP161814 7/8 EP162008 1.0030 1.2540 1/2
(P100-7) (P102-4)
EP161816 1 EP162012 3/4
(P100-8) (P102-6)
EP161820 1- 1/4 EP162014 7/8
(P100-10) (P102-7)
EP161824 1- 1/2 EP162016 1
(P100-12) (P102-8)
EP161828 1- 3/4 EP162020 1- 1/4
(P100-14) (P102-10)
EP161832 2 EP162022 1- 3/8
(P100-16) (P102-11)
EP162024 1- 1/2
AA1110-8 1.0010 1.1280 1/2 (P102-12)
AA1110-10 3/4 EP162028 1- 3/4
AA1110-2 13/16 (P102-14)
AA1110-1 1
AA1110-3 1- 1/4 EP162032 2
AA1110-12 1- 3/8 (P102-16)
AA1110 1- 1/2 EP162036 2- 1/4
(P102-18)
56
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP162040 1.0030 1.2540 2- 1/2 EP162124 1.0030 1.3165 1- 1/2
(P102-20) (P103-12)
EP162048 3 EP162128 1- 3/4
(P102-24) (P103-14)
EP162132 2
AA1232-6 1.0030 1.2530 3/4 (P103-16)
AA1232 1 EP162140 2- 1/2
AA1232-2 1- 1/8 (P103-20)
AA1232-3 1- 1/4
AA1232-7 1- 1/2 EP162148 3
AA1232-8 1- 3/4 (P103-24)
AA1232-4 2
AA1232-5 2- 1/2 AA1304-3 1.0010 1.3160 1
AA1304 1- 1/2
AA1204-7 1.0050 1.2525 1 AA1304-4 1- 3/4
AA1204-2 1- 1/4 AA1304-6 2
AA1204-1 1- 3/8
AA1204 1- 1/2 AA1325-10 1.0020 1.3150 1
AA1204-3 2 AA1325-8 1- 1/4
AA1204-5 2- 1/4 AA1325-4 1- 1/2
AA1204-4 2- 1/2 AA1325-7 1- 5/8
AA1325-5 1- 3/4
AA1212-7 1.0010 1.2520 1/2 AA1325 2
AA1212-6 3/4 AA1325-1 2- 1/2
AA1212-2 1 AA1325-3 2- 3/4
AA1212-16 1- 1/4 AA1325-2 3
AA1212-11 1- 1/2
AA1212-4 1- 3/4 1 X 1- 3/8 NOMINAL
AA1212-3 2
AA1212-5 2- 1/4 EP162216 1.0030 1.3790 1
AA1212 2- 1/2 (P104-8)
AA1212-8 2- 7/8 EP162220 1- 1/4
AA1212-14 3 (P104-10)
AA1213-6 1.0020 1.2520 7/8 EP162224 1- 1/2
AA1213-3 1 (P104-12)
AA1213-10 1- 1/8 EP162228 1- 3/4
AA1213-12 1- 1/4 (P104-14)
AA1213-1 1- 1/2 EP162232 2
AA1213-2 1- 3/4 (P104-16)
AA1213 2
AA1213-14 2- 1/2 EP162240 2- 1/2
AA1213-15 3 (P104-20)
1 X 1- 5/16 NOMINAL AA1334-3 1.0010 1.3780 3/4
EP162116 1.0030 1.3165 1 AA1334-5 1- 1/4
AA1334-1 1- 1/2
(P103-8) AA1334-2 2
EP162120 1- 1/4
(P103-10) AA1310-2 1.0030 1.3770 1
AA1310-1 1- 1/8
57
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA1310-4 1.0030 1.3770 1- 1/4 AA1250-2 1.1270 1.2525 1- 1/4
AA1310 1- 3/8 AA1250-3 1- 1/2
AA1310-5 1- 1/2
AA1310-8 1- 3/4 1- 1/8 X 1- 5/16 NOMINAL
AA1310-3 2 EP182116 1.1280 1.3165 1
AA1310-6 2- 1/4 (P113-8)
1 X 1- 1/2 NOMINAL EP182120 1- 1/4
AA1511-7 1.0035 1.5045 1 (P113-10)
AA1511-8 1- 1/4 EP182124 1- 1/2
AA1511-5 1- 1/2 (P113-12)
AA1511-1 2 EP182128 1- 3/4
(P113-14)
EP162416 1.0030 1.5040 1
(P105-8) EP182132 2
EP162420 1- 1/4 (P113-16)
(P105-10)
AA1317 1.1265 1.3155 1
EP162424 1- 1/2 AA1317-1 1- 1/4
(P105-12)
EP162428 1- 3/4 1- 1/8 X 1- 3/8 NOMINAL
(P105-14)
AA1319-10 1.1290 1.3790 1/2
EP162432 2 AA1319-3 1
(P105-16) AA1319 1- 1/4
EP162440 2- 1/2 AA1319-13 1- 1/2
(P105-20) AA1319-5 1- 3/4
AA1319-1 2
EP162448 3 AA1319-12 2- 1/4
(P105-24) AA1319-2 2- 1/2
1- 1/16 X 1- 5/16 NOMINAL EP182208 1.1280 1.3790 1/2
AA1307-2 1.0640 1.3170 3/4 (P114-4)
AA1307-4 1 EP182212 3/4
AA1307-5 1- 1/4 (P114-6)
AA1307-1 1- 1/2 EP182216 1
1- 1/8 X 1- 1/4 NOMINAL (P114-8)
EP182220 1- 1/4
EP182016 1.1280 1.2540 1 (P114-10)
(P112-8)
EP182224 1- 1/2
EP182020 1- 1/4 (P114-12)
(P112-10)
EP182228 1- 3/4
EP182024 1- 1/2 (P114-14)
(P112-12)
EP182232 2
(P114-16)
AA1214-6 1.1245 1.2535 7/8
AA1214-3 1 EP182240 2- 1/2
AA1214-2 1- 1/8 (P114-20)
AA1214-1 1- 1/4 EP182248 3
AA1214-8 1- 1/2 (P114-24)
58
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA1332-6 1.1270 1.3770 1/2 EP192332 1.1905 1.4415 2
AA1332-1 3/4 (P118-16)
AA1332-4 1 EP192340 2- 1/2
AA1332-9 1- 1/4 (P118-20)
AA1332-7 1- 1/2
AA1332-10 1- 3/4 EP192348 3
AA1332 2 (P118-24)
AA1332-11 2- 1/4
AA1332-2 2- 1/2 AA1403-3 1.1885 1.4410 1- 1/4
AA1332-8 3 AA1403-7 1- 1/2
AA1403-10 2
1- 1/8 X 1- 1/2 NOMINAL
EP182416 1.1280 1.5040 1 1- 3/16 X 1- 1/2 NOMINAL
(P115-8) AA1504-6 1.1930 1.5040 1
EP182420 1- 1/4 AA1504-1 1- 1/2
(P115-10)
EP182424 1- 1/2 AA1523-2 1.1900 1.5040 1
(P115-12) AA1523-5 1- 1/2
AA1523 2
EP182428 1- 3/4 AA1523-3 2- 1/2
(P115-14)
EP182432 2 EP192416 1.1905 1.5040 1
(P115-16) (P119-8)
EP182440 2- 1/2 EP192420 1- 1/4
(P115-20) (P119-10)
EP192424 1- 1/2
AA1502 1.1270 1.5035 1 (P119-12)
AA1502-2 1- 1/4 EP192428 1- 3/4
AA1502-3 1- 1/2 (P119-14)
AA1509-4 1.1260 1.5030 1 EP192432 2
AA1509-1 1- 1/2 (P119-16)
AA1509-6 1- 3/4 EP192440 2- 1/2
AA1509 2 (P119-20)
AA1509-3 2- 1/2
EP192448 3
1- 3/16 X 1- 5/16 NOMINAL (P119-24)
AA1339-2 1.1890 1.3155 1
AA1339 1- 1/4 1- 1/4 X 1- 7/16 NOMINAL
59
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
AA1528-3 1.2535 1.5040 1- 1/4 AA1512-1 1.2520 1.5020 1- 7/8
AA1528-4 1- 1/2 AA1512-5 2
AA1512-13 2- 1/2
EP202408 1.2535 1.5040 1/2
(P125-4) AA1517-4 1.2500 1.5020 3/4
AA1517-6 1- 1/4
EP202410 5/8 AA1517-1 1- 5/8
(P125-5)
EP202412 3/4 1- 1/4 X 1- 9/16 NOMINAL
(P125-6) AA1506-12 1.2520 1.5650 1- 1/4
EP202414 7/8 AA1506-6 1- 1/2
(P125-7) AA1506 1- 3/4
EP202416 1 AA1506-7 2
(P125-8) AA1506-8 2- 1/4
EP202418 1- 1/8 1- 1/4 X 1- 5/8 NOMINAL
(P125-9) EP202616 1.2535 1.6300 1
EP202420 1- 1/4 (P126-8)
(P125-10) EP202620 1- 1/4
EP202422 1- 3/8 (P126-10)
(P125-11) EP202624 1- 1/2
EP202424 1- 1/2 (P126-12)
(P125-12) EP202628 1- 3/4
EP202426 1- 5/8 (P126-14)
(P125-13) EP202632 2
EP202428 1- 3/4 (P126-16)
(P125-14) EP202640 2- 1/2
EP202430 1- 7/8 (P126-20)
(P125-15) EP202648 3
EP202432 2 (P126-24)
(P125-16)
EP202436 2- 1/4 AA1604 1.2540 1.6290 1- 1/2
(P125-18) AA1604-2 1- 3/4
EP202440 2- 1/2
(P125-20) AA1606-9 1.2520 1.6275 1
AA1606 1- 1/4
EP202448 3 AA1606-7 1- 1/2
(P125-24) AA1606-11 1- 5/8
AA1606-1 1- 3/4
AA1512-12 1.2520 1.5020 1/2 AA1606-3 2
AA1512-11 5/8 AA1606-5 2- 1/2
AA1512-14 3/4 AA1606-4 3
AA1512-7 7/8
AA1512-15 1 AA1602 1.2500 1.6270 1- 1/2
AA1512-16 1- 1/4
AA1512-3 1- 3/8 1- 1/4 X 1- 3/4 NOMINAL
AA1512-2 1- 1/2 EP202828 1.2535 1.7550 1- 3/4
AA1512-17 1- 3/4 (P127-14)
60
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP202832 1.2535 1.7550 2 EP222632 1.3785 1.6300 2
(P127-16) (P137-16)
EP202840 2- 1/2 EP222640 2- 1/2
(P127-20) (P137-20)
EP202848 3 EP222648 3
(P127-24) (P137-24)
61
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
1- 7/16 X 1- 3/4 NOMINAL EP242824 1.5040 1.7550 1- 1/2
(P150-12)
EP232816 1.4410 1.7550 1
EP242828 1- 3/4
(P144-8)
(P150-14)
EP232820 1- 1/4
EP242832 2
(P144-10)
(P150-16)
EP232824 1- 1/2
EP242836 2- 1/4
(P144-12)
(P150-18)
EP232828 1- 3/4
EP242840 2- 1/2
(P144-14)
(P150-20)
EP232832 2
EP242848 3
(P144-16)
(P150-24)
EP232840 2- 1/2
(P144-20) AA1704-20 1.5030 1.7540 1/2
EP232848 3 AA1704-21 5/8
(P144-24) AA1704-16 3/4
AA1704-4 7/8
AA1703-1 1.4425 1.7535 7/8 AA1704-15 1
AA1703-14 1- 1/8 AA1704-17 1- 1/8
AA1703-4 1- 1/4 AA1704-11 1- 1/4
AA1703-6 1- 1/2 AA1704-5 1- 3/8
AA1703-3 1- 3/4 AA1704 1- 1/2
AA1703 1- 7/8 AA1704-3 1- 3/4
AA1703-7 2 AA1704-2 2
AA1703-10 2- 1/4 AA1704-7 2- 1/4
AA1703-5 2- 1/2 AA1704-8 2- 1/2
AA1704-9 3
1- 1/2 X 1-11/16 NOMINAL AA1704-19 3- 1/2
AA1612-4 1.5070 1.6910 3/4 1- 1/2 X 1-13/16 NOMINAL
AA1612-1 1
1- 1/2 X 1- 3/4 NOMINAL EP242916 1.5040 1.8175 1
(P151-8)
EP242808 1.5040 1.7550 1/2
EP242924 1- 1/2
(P150-4)
(P151-12)
EP242810 5/8
EP242926 1- 5/8
(P150-5)
(P151-13)
EP242812 3/4
(P150-6) AA1801-1 1.5020 1.8150 1
EP242814 7/8 AA1801 1- 5/8
(P150-7)
1- 1/2 X 1- 7/8 NOMINAL
EP242816 1
(P150-8) EP243024 1.5040 1.8800 1- 1/2
EP242820 1- 1/4 (P152-12)
(P150-10) EP243032 2
EP242822 1- 3/8 (P152-16)
(P150-11)
62
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP243040 1.5040 1.8800 2- 1/2 EP263040 1.6290 1.8800 2- 1/2
(P152-20) (P162-20)
EP243044 2- 3/4 EP263048 3
(P152-22) (P162-24)
EP243048 3
(P152-24) AA1803-10 1.6270 1.8790 1
AA1803-11 1- 1/4
AA1807-9 1.5030 1.8780 1- 1/2 AA1803-13 1- 1/2
AA1807-10 1- 3/4 AA1803-14 1- 3/4
AA1807 2 AA1803-7 2
AA1807-11 2- 1/2 AA1803-1 2- 1/4
AA1807-1 2- 3/4 AA1803-15 2- 3/4
AA1807-2 3 1- 5/8 X 2 NOMINAL
1- 1/2 X 2 NOMINAL EP263216 1.6290 2.0050 1
EP243216 1.5040 2.0050 1 (P163-8)
(P153-8) EP263224 1- 1/2
EP243224 1- 1/2 (P163-12)
(P153-12) EP263232 2
EP243232 2 (P163-16)
(P153-16) EP263240 2- 1/2
EP243240 2- 1/2 (P163-20)
(P153-20) EP263248 3
EP243248 3 (P163-24)
(P153-24)
AA2000-5 1.6265 2.0040 1- 1/2
EP243256 3- 1/2 AA2000-1 2
(P153-28) AA2000-3 2- 1/2
AA2000-4 3
AA2007-6 1.5030 2.0040 1
AA2007-2 2 1-11/16 X 2- 3/16 NOMINAL
AA2007-3 2- 1/2 EP273528 1.6915 2.1925 1- 3/4
AA2007-5 3- 1/2 (P168-14)
1- 5/8 X 1- 7/8 NOMINAL EP273532 2
EP263020 1.6290 1.8800 1- 1/4 (P168-16)
(P162-10) EP273548 3
EP263024 1- 1/2 (P168-24)
(P162-12) EP273564 4
EP263028 1- 3/4 (P168-32)
(P162-14)
AA2107-1 1.6905 2.1915 2
EP263032 2 AA2107 4
(P162-16)
EP263036 2- 1/4 1- 3/4 X 1-15/16 NOMINAL
(P162-18) AA1904-2 1.7525 1.9415 1- 1/4
AA1904-3 1- 1/2
63
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
1- 3/4 X 2 NOMINAL AA2202-2 1.8780 2.2540 3
EP283216 1.7540 2.0050 1 1-15/16 X 2- 1/8 NOMINAL
(P175-8) AA2102-3 1.9400 2.1285 2
EP283220 1- 1/4 AA2102-1 2- 1/2
(P175-10)
1-15/16 X 2- 5/16 NOMINAL
EP283224 1- 1/2
(P175-12) EP313732 1.9415 2.3175 2
(P193-16)
EP283228 1- 3/4
(P175-14) EP313740 2- 1/2
(P193-20)
EP283232 2
(P175-16) EP313748 3
(P193-24)
EP283240 2- 1/2
(P175-20) EP313764 4
(P193-32)
EP283248 3
(P175-24)
AA2306-3 1.9405 2.3165 2
AA2306-5 3
AA2001-11 1.7530 2.0040 1 AA2306 4
AA2001-3 1- 1/2
AA2001 1- 7/8 1-15/16 X 2- 7/16 NOMINAL
AA2001-9 2
AA2001-1 2- 1/2 AA2403-1 1.9420 2.4415 1- 1/2
AA2001-13 2- 3/4 AA2403-2 2
AA2001-2 3 2 X 2- 1/4 NOMINAL
1- 3/4 X 2- 1/8 NOMINAL EP323612 2.0040 2.2550 3/4
(P200-6)
EP283424 1.7540 2.1300 1- 1/2
(P176-12) EP323616 1
(P200-8)
EP283432 2
(P176-16) EP323624 1- 1/2
(P200-12)
EP283448 3
(P176-24) EP323632 2
(P200-16)
AA2112-8 1.7540 2.1280 1/2 EP323640 2- 1/2
AA2112-1 1- 1/2 (P200-20)
AA2112-2 2 EP323648 3
AA2112-3 2- 1/2 (P200-24)
1- 3/4 X 2- 1/4 NOMINAL
AA2203-5 2.0030 2.2540 3/4
AA2204-2 1.7530 2.2530 2 AA2203-6 1
AA2204-3 2- 1/2 AA2203-7 1- 1/2
AA2204 3 AA2203 2
1- 7/8 X 2- 1/4 NOMINAL AA2203-9 2- 1/2
AA2203-10 3
AA2202-10 1.8780 2.2540 3/4
AA2202 2
AA2202-1 2- 1/2
64
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
2 X 2- 3/8 NOMINAL AA2501-1 2.0030 2.5030 1- 1/2
AA2501-2 2
EP323818 2.0040 2.3800 1- 1/8 AA2501-3 2- 1/2
(P201-9) AA2501 3
EP323824 1- 1/2
2- 3/16 X 2- 3/8 NOMINAL
(P201-12)
EP323828 1- 3/4 AA2303-1 2.1900 2.3790 1- 1/2
(P201-14) 2- 1/4 X 2- 5/8 NOMINAL
EP323832 2
(P201-16) EP364232 2.2540 2.6310 2
(P225-16)
EP323840 2- 1/2
(P201-20) EP364240 2- 1/2
(P225-20)
EP323844 2- 3/4
(P201-22) EP364248 3
(P225-24)
EP323848 3
(P201-24)
AA2605-3 2.2540 2.6295 2
EP323856 3- 1/2 AA2605-5 3
(P201-28) AA2605 3- 1/2
EP323864 4 AA2605-2 4- 1/2
(P201-32) 2- 1/4 X 2- 3/4 NOMINAL
AA2304-6 2.0030 2.3790 1- 1/8 EP364432 2.2540 2.7560 2
AA2304-7 1- 1/2 (P226-16)
AA2304 1- 3/4 EP364448 3
AA2304-1 2 (P226-24)
AA2304-2 2- 1/2
AA2304-3 3 AA2703-1 2.2530 2.7530 1- 1/2
AA2304-4 3- 1/2 AA2703-2 2
AA2304-5 4 AA2703 3
2 X 2- 1/2 NOMINAL 2- 3/8 X 2- 5/8 NOMINAL
EP324016 2.0040 2.5050 1
(P202-8) AA2602-3 2.3770 2.6295 1- 1/4
AA2602 1- 5/8
EP324024 1- 1/2
(P202-12) 2- 3/8 X 2- 3/4 NOMINAL
EP324032 2 EP384432 2.3790 2.7560 2
(P202-16) (P237-16)
EP324040 2- 1/2 EP384440 2- 1/2
(P202-20) (P237-20)
EP324048 3 EP384448 3
(P202-24) (P237-24)
EP324056 3- 1/2
(P202-28) AA2701-2 2.3790 2.7530 2
AA2701-6 2- 1/2
EP324064 4 AA2701 3
(P202-32)
65
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
2- 1/2 X 2- 3/4 NOMINAL 2- 3/4 X 3- 1/4 NOMINAL
EP404432 2.5050 2.7560 2 EP445232 2.7550 3.2570 2
(P250-16) (P275-16)
EP404448 3 EP445248 3
(P250-24) (P275-24)
EP404464 4 EP445264 4
(P250-32) (P275-32)
66
Powdered Metal
Plane Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. LENGTH NUMBER I.D. O.D. LENGTH
EP566448 3.5070 4.0080 3 AA4500 4.0035 4.5040 4
(P350-24) AA4500-2 6
EP566456 3- 1/2 4 X 4- 5/8 NOMINAL
(P350-28) AA4600-5 4.0030 4.6280 4
EP566464 4
(P350-32) 4- 1/2 X 5- 1/4 NOMINAL
AA5201 4.5040 5.2545 5
AA4000-3 3.5035 4.0040 2
AA4000-5 3 5 X 5- 3/4 NOMINAL
AA4000-6 3- 1/2 AA5700-1 5.0040 5.7550 2
AA4000 4
4 X 4- 1/2 NOMINAL
EP647264 4.0080 4.5090 4
(P400-32)
67
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
1/8 X 1/4 NOMINAL
FF207-2 .1260 .2520 1/4 5/16 1/16
FF207-3 3/8
1/8 X 5/16 NOMINAL
FFB25-2 .1270 .3150 1/4 3/8 3/64
FFB25-3 3/8
3/16 X 5/16 NOMINAL
EF030503 .1895 .3155 3/16 7/16 1/16
(FL19-1.5)
EF030504 1/4
(FL19-2)
EF030505 5/16
(FL19-2.5)
EF030506 3/8
(FL19-3)
EF030508 1/2
(FL19-4)
68
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
EF040608 .2520 .3780 1/2 1/2 1/16
(FL26-4)
EF040610 5/8
(FL26-5)
EF040612 3/4
(FL26-6)
69
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
FF411-1 .3125 .4400 3/8 9/16 1/16
FF411-2 1/2
FF411-4 7/8
70
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
3/8 X 9/16 NOMINAL
EF060908 .3770 .5655 1/2 11/16 1/16
(FL39-4)
EF060912 3/4
(FL39-6)
71
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
7/16 X 5/8 NOMINAL
EF071012 .4395 .6280 3/4 7/8 1/8
(FL44-6)
EF071020 1- 1/4
(FL44-10)
72
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
FFB810-4 .5020 .6280 1/2 7/8 1/8
FFB810-5 5/8
FFB810-6 3/4
FFB810-8 1
FFB810-10 1- 1/4
FFB810-12 1- 1/2
1/2 X 11/16 NOMINAL
EF081105 .5020 .6905 5/16 7/8 1/8
(FL51-2.5)
EF081108 1/2
(FL51-4)
EF081112 3/4
(FL51-6)
73
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
FFB812-4 .5020 .7530 1/2 1 1/8
FFB812-6 3/4
FFB812-7 7/8
FFB812-8 1
FFB812-10 1- 1/4
FFB812-12 1- 1/2
9/16 X 3/4 NOMINAL
FFB912-8 .5650 .7530 1 1 1/8
5/8 X 3/4 NOMINAL
EF101210 .6270 .7530 5/8 1 1/8
(FL62-5)
EF101212 3/4
(FL62-6)
EF101216 1
(FL62-8)
EF101218 1- 1/8
(FL62-9)
74
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
FF842-1 .6260 .8150 1/2 1 1/8
FF842-2 3/4
FF842-3 1
75
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
FF838-1 .7510 .8770 1/2 1 1/16
FF838-3 1
3/4 X 1 NOMINAL
EF121610 .7520 1.0040 5/8 1- 1/4 3/16
(FL77-5)
EF121612 3/4
(FL77-6)
EF121616 1
(FL77-8)
EF121618 1- 1/8
(FL77-9)
EF121620 1- 1/4
(FL77-10)
EF121624 1- 1/2
(FL77-12)
76
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
FF1011-2 .7505 1.0020 1/2 1- 7/16 1/8
FF1011 5/8
FF1011-4 1
FF1011-1 1- 1/8
77
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
78
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
1 X 1- 3/8 NOMINAL
EF162212 1.0030 1.3790 3/4 1- 5/8 3/16
(FL104-6)
EF162216 1
(FL104-8)
EF162224 1- 1/2
(FL104-12)
EF162228 1- 3/4
(FL104-14)
EF162232 2
(FL104-16)
79
Powdered Metal
Flange Bearings
SAE 841 Bronze
PART FLANGE
NUMBER I.D. O.D. LENGTH O.D. THK.
1- 1/2 X 1- 3/4 NOMINAL
EF242824 1.5040 1.7550 1- 1/2 2 3/16
(FL150-12)
80
Powdered Metal
Thrust Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. THK. NUMBER I.D. O.D. THK.
1/4 X 7/16 NOMINAL 1/2 X 1 NOMINAL
TT400 .2550 .4375 1/16 EW081601 .5020 1.0040 1/16
(TW51)
1/4 X 1/2 NOMINAL EW081601.5 3/32
TT504 .2550 .5000 1/16 (TW51.5)
EW081602 1/8
1/4 X 5/8 NOMINAL (TW52)
EW041001 .2520 .6280 1/16
(TW25) TT1001 .5100 1.0000 1/16
TT1001-2 3/32
TT601 .2550 .6250 1/16 TT1001-1 1/8
81
Powdered Metal
Thrust Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. THK. NUMBER I.D. O.D. THK.
5/8 X 1- 1/2 NOMINAL 1 X 1- 1/2 NOMINAL
TT1508-1 .6560 1.5000 1/16 EW162401 1.0030 1.5040 1/16
TT1508-2 1/8 (TW99)
EW162402 1/8
3/4 X 1- 1/4 NOMINAL (TW100)
EW122001 .7520 1.2540 1/16
(TW75) TT1502-2 1.0030 1.5040 1/16
EW122002 1/8 TT1502 1/8
(TW76) TT1502-1 3/16
82
Powdered Metal
Thrust Bearings
SAE 841 Bronze
PART PART
NUMBER I.D. O.D. THK. NUMBER I.D. O.D. THK.
1- 1/4 X 2 NOMINAL 1- 3/4 X 2- 7/16 NOMINAL
EW203201 1.2535 2.0050 1/16 TT2400-1 1.7550 2.4400 1/8
(TW126.5)
EW203202 1/8 1- 3/4 X 2- 5/8 NOMINAL
(TW126) EW284202 1.7540 2.6310 1/8
(TW175)
TT2006 1.2650 2.0000 1/16
TT2006-1 1/8 TT2601 1.7650 2.6250 1/8
1- 1/4 X 2- 3/8 NOMINAL 1-15/16 X 2- 5/8 NOMINAL
TT2304-1 1.2650 2.3750 1/16 TT2600 1.9530 2.6250 1/8
TT2304-2 1/8
2 X 3 NOMINAL
1- 1/4 X 3- 5/16 NOMINAL
EW324802 2.0040 3.0060 1/8
TT3301 1.2550 3.3120 1/16 (TW200)
TT3301-1 1/8 EW324804 1/4
1- 3/8 X 1-15/16 NOMINAL (TW201)
TT1900 1.3790 1.9400 1/8 TT3001-3 2.0110 3.0000 1/8
1- 1/2 X 2 NOMINAL TT3001 3/16
TT3001-1 1/4
TT2008 1.5030 2.0000 1/8
2 X 3- 5/8 NOMINAL
1- 1/2 X 2- 1/2 NOMINAL
TT3600 2.0310 3.6250 3/16
EW244002 1.5040 2.5050 1/8
(TW150) 2- 1/16 X 4 NOMINAL
1- 1/2 X 3- 1/2 NOMINAL TT4002-1 2.0620 4.0000 1/8
TT4002 1/4
EW245603 1.5040 3.5070 3/16
(TW151) 2- 1/2 X 3- 1/4 NOMINAL
TT3200 2.5020 3.2500 1/8
TT3500-1 1.5100 3.5000 3/16
2- 3/4 X 3- 7/8 NOMINAL
1- 9/16 X 2- 7/16 NOMINAL
TT3800 2.7660 3.8750 1/4
TT2402 1.5780 2.4375 1/8
83
Powdered Metal Bronze
Bearing Maintenance Kit
A selection of Bunting quality powdered metal bronze self-lubricating
plane bearings are available in a convenient Maintenance Kit.
84
Bunting Powdered Metal
Cored Bronze Bars
SAE 841 Bronze
Powdered Metal
Circular Bronze Discs
SAE 841 Bronze
THICKNESS
PART NUMBER I.D. O.D. +.0025"
DD 3000 SOLID 3 1/4
DD 4000 4 1/4
DD 5602 01* 5-5/8 1/4
86
Powdered Metal
Circular Bronze Discs
SAE 841 Bronze
THICKNESS
PART NUMBER I.D. O.D. +.0025"
DD 6000* SOLID 6 5/16
DD 7001** 7 5/16
DD 8000** 8 5/16
DD 8000 03** 8 3/8
CD 3001 1 3 1/4
CD 4001 1 4 1/4
CD 4002 2 4 1/4
CD 5500* 2 5- 1/2 1/4
CD 4502 2- 1/4 4- 1/2 1/4
CD 7000 02* 2-1/4 7 1/4
CD 9001*** 3 9 5/16
CD 6003* 4 6 5/16
* Thickness +.0035
** Thickness +.0050
***Thickness +.0040
I.D. and O.D. will finish to dimensions shown.
Powdered Metal
Bronze Plate
SAE 841 Bronze
THICKNESS
PART NUMBER WIDTH LENGTH +.005"
PP 2500 1/2 2-1/2 1/4
PP 8100 01 2 8-1/8 1/4
PP 8100 1/2
PP 12100 3 12 1/4
PP 12100 01 1/2
PP 12100 02 3/4
PP 12100 03 1
PP 6000 5 6 1/8
PP 6000 01 3/16
PP 6000 02 1/4
PP 6000 04 3/8
PP 6000 05 1/2
PP 6000 06 5/8
PP 6000 07 3/4
PP 6000 08 1
PP 8000 07 5 8 1/8
PP 8000 3/16
PP 8000 01 1/4
PP 8000 04 1/2
PP 8000 05 3/4
PP 8000 06 1
87
Powdered Metal
Bronze Plate
SAE 841 Bronze
THICKNESS
PART NUMBER WIDTH LENGTH +.005"
PP 12000 06 6 12 1/8
PP 12000 07 3/16
PP 12000 1/4
PP 12000 01 3/8
PP 12000 02 1/2
PP 12000 03 5/8
PP 12000 04 3/4
PP 12000 05 1
LG.
88
Bunting Lube-Align®
Mounted Bearings
The unique, patented* Lube-Align bearing products are made of self-
lubricating, self-aligning SAE 841 bronze bearings permanently cast
inside a ‘fast mount’ aluminum housing. Here’s how Lube-Align
bearings effect 4-way savings for OEM and maintenance engineers:
89
Lube-Align® Bearings
Standard Mounting
PART
NUMBER I.D. A B C D E G H I J
LA002806* .127/.126 3/8 1-1/8 3/8 3/16 11/64 1-5/8 3/8 3/4 1/64
LA003806* .1895/.1885 3/8 1-1/8 3/8 3/16 11/64 1-5/8 3/8 3/4 1/64
LA031007* .1895/.1885 7/16 1-3/8 7/16 1/4 13/64 1-7/8 7/16 7/8 1/64
LA004806* .252/.251 3/8 1-1/8 3/8 3/16 11/64 1-5/8 3/8 3/4 1/64
LA041007* .252/.251 7/16 1-3/8 7/16 1/4 13/64 1-7/8 7/16 7/8 1/64
LA041208 .252/.251 9/16 1-3/4 1/2 1/4 9/32 2-1/4 9/16 1-1/8 1/64
LA041209 .252/.251 9/16 1-3/4 19/32 1/4 9/32 2-1/4 9/16 1-1/8 1/32
LA051007 .3135/.3145 7/16 1-3/8 7/16 1/4 13/64 1-7/8 7/16 7/8 1/64
LA061208 .377/.376 9/16 1-3/4 1/2 1/4 9/32 2-1/4 9/16 1-1/8 1/64
LA081208 .502/.501 9/16 1-3/4 1/2 1/4 9/32 2-1/4 9/16 1-1/8 1/64
LA082014 .502/.501 13/16 2-1/2 7/8 5/16 11/32 3-1/4 3/4 1-9/16 1/64
LA082416 .502/.501 15/16 3-1/8 1 13/32 11/32 4 1 1-15/16 1/64
LA102014 .6275/.6265 13/16 2-1/2 7/8 5/16 11/32 3-1/4 3/4 1-9/16 1/64
LA102416 .6275/.6265 15/16 3-1/8 1 13/32 11/32 4 1 1-15/16 1/64
LA122014 .752/.751 13/16 2-1/2 7/8 5/16 11/32 3-1/4 3/4 1-9/16 1/64
LA122416 .752/.751 15/16 3-1/8 1 13/32 11/32 4 1 1-15/16 1/64
LA142416 .877/.876 15/16 3-1/8 1 13/32 11/32 4 1 1-15/16 1/64
LA162416 1.002/1.001 15/16 3-1/8 1 13/32 11/32 4 1 1-15/16 1/64
LA163424 1.002/1.001 1-5/16 4 1-1/2 9/16 9/16 5 1-1/4 2-9/16 1/64
LA203424 1.253/1.251 1-5/16 4 1-1/2 9/16 9/16 5 1-1/4 2-9/16 1/64
LA243724* 1.503/1.501 1-1/2 4-1/2 1-1/2 9/16 9/16 5-1/2 1-1/2 3 1/32
LA284832 1.753/1.751 1-15/16 5-1/2 2 3/4 13/16 6-1/2 1-7/8 3-13/16 1/32
LA324832 2.004/2.001 1-15/16 5-1/2 2 3/4 13/16 6-1/2 1-7/8 3-13/16 1/32
*When reserve inventory is depleted, these sizes
90 will be supplied on special order basis only.
Lube-Align® Bearings
2-Bolt Flange Mounting
PART
NUMBER I.D. A B C D E F J K
LT002806* .127/.126 3/4 1-1/4 13/32 3/16 11/64 1-5/8 1/64 1/32
LT003806 .1895/.1885 3/4 1-1/4 13/32 3/16 11/64 1-5/8 1/64 1/32
LT031007* .1895/.1885 7/8 1-3/8 15/32 3/16 13/64 1-7/8 1/32 1/32
LT004806 .252/.251 3/4 1-1/4 13/32 3/16 11/64 1-5/8 1/64 1/32
LT041007* .252/.251 7/8 1-3/8 15/32 3/16 13/64 1-7/8 1/32 1/32
LT041208* .252/.251 1-1/8 1-3/4 17/32 3/16 9/32 2-1/4 1/32 1/32
LT051007 .3135/.3145 7/8 1-3/8 15/32 3/16 13/64 1-7/8 1/32 1/32
LT061208 .377/.376 1-1/8 1-3/4 17/32 3/16 9/32 2-1/4 1/32 1/32
LT081208 .502/.501 1-1/8 1-3/4 17/32 3/16 9/32 2-1/4 1/32 1/32
LT082014 .502/.501 1-5/8 2-1/2 15/16 1/4 13/32 3-1/4 1/32 1/16
LT082416 .502/.501 1-7/8 3-1/8 1-1/16 5/16 13/32 4 1/32 1/16
LT102014 .6275/.6265 1-5/8 2-1/2 15/16 1/4 13/32 3-1/4 1/32 1/16
LT102416 .6275/.6265 1-7/8 3-1/8 1-1/16 5/16 13/32 4 1/32 1/16
LT122014 .752/.751 1-5/8 2-1/2 15/16 1/4 13/32 3-1/4 1/32 1/16
LT122416 .752/.751 1-7/8 3-1/8 1-1/16 5/16 13/32 4 1/32 1/16
LT142416 .877/.876 1-7/8 3-1/8 1-1/16 5/16 13/32 4 1/32 1/16
LT162416 1.002/1.001 1-7/8 3-1/8 1-1/16 5/16 13/32 4 1/32 1/16
LT163424 1.002/1.001 2-5/8 4 1-5/8 3/8 9/16 5 1/32 1/8
LT203424 1.253/1.251 2-5/8 4 1-5/8 3/8 9/16 5 1/32 1/8
LT284832* 1.753/1.751 3-7/8 5-1/2 2-1/8 5/8 13/16 7 1/32 1/8
LT324832 2.004/2.001 3-7/8 5-1/2 2-1/8 5/8 13/16 7 1/32 1/8
PART
NUMBER I.D. A B C D E F J K
LF031007* .1895/.1885 7/8 1-3/8 15/32 3/16 5/32 1/4 1/32 1/32
LF041007* .252/.251 7/8 1-3/8 15/32 3/16 5/32 1/4 1/32 1/32
LF041208* .252/.251 1-1/8 1-3/4 17/32 3/16 9/32 5/16 1/32 1/32
LF051007* .3135/.3145 7/8 1-3/8 15/32 3/16 5/32 1/4 1/32 1/32
LF061208* .377/.376 1-1/8 1-3/4 17/32 3/16 9/32 5/16 1/32 1/32
LF081208 .502/.501 1-1/8 1-3/4 17/32 3/16 9/32 5/16 1/32 1/32
LF082014* .502/.501 1-5/8 2-1/2 15/16 1/4 13/32 7/16 1/32 1/16
LF082416* .502/.501 1-7/8 3-1/8 1-1/16 5/16 13/32 5/8 1/32 1/16
LF102014 .6275/.6265 1-5/8 2-1/2 15/16 1/4 13/32 7/16 1/32 1/16
LF102416* .6275/.6265 1-7/8 3-1/8 1-1/16 5/16 13/32 5/8 1/32 1/16
LF122014 .752/.751 1-5/8 2-1/2 15/16 1/4 13/32 7/16 1/32 1/16
LF122416 .752/.751 1-7/8 3-1/8 1-1/16 5/16 13/32 5/8 1/32 1/16
LF142416* .877/.876 1-7/8 3-1/8 1-1/16 5/16 13/32 5/8 1/32 1/16
LF162416* 1.002/1.001 1-7/8 3-1/8 1-1/16 5/16 13/32 5/8 1/32 1/16
LF163424 1.002/1.001 2-5/8 4 1-5/8 3/8 9/16 11/16 1/32 1/8
LF203424 1.253/1.251 2-5/8 4 1-5/8 3/8 9/16 11/16 1/32 1/8
LF284832 1.753/1.751 3-7/8 5-1/2 2-1/8 5/8 13/16 13/16 1/32 1/8
LF324832* 2.004/2.001 3-7/8 5-1/2 2-1/8 5/8 13/16 13/16 1/32 1/8
*When reserve inventory is depleted, these sizes
92 will be supplied on special order basis only.
Lube-Align® Bearings
Bore Mounting
PART FRACTION
NUMBER I.D. O.D. A C J
LC041608* .252/.251 1 1.003/1.002 1/2 1/32
LC041708* .252/.251 1-1/16 1.0655/1.0645 1/2 1/32
LC041809* .252/.251 1-1/8 1.128/1.127 19/32 1/32
LC042009* .252/.251 1-1/4 1.253/1.252 19/32 1/32
LC051407 .3135/.3145 7/8 .878/.877 7/16 1/64
LC051507 .3135/.3145 15/16 .9405/.9395 7/16 1/64
LC061608 .377/.376 1 1.003/1.002 1/2 1/32
LC061708* .377/.376 1-1/16 1.0655/1.0645 1/2 1/32
LC081608 .502/.501 1 1.003/1.002 1/2 1/32
LC081708* .502/.501 1-1/16 1.0655/1.0645 1/2 1/32
LC082414* .502/.501 1-1/2 1.503/1.502 7/8 1/32
LC082614* .502/.501 1-5/8 1.628/1.627 7/8 1/32
LC082816* .502/.501 1-3/4 1.753/1.752 1 1/32
LC083016* .502/.501 1-7/8 1.878/1.877 1 1/32
LC102414 .6275/.6265 1-1/2 1.503/1.502 7/8 1/32
LC102614* .6275/.6265 1-5/8 1.628/1.627 7/8 1/32
LC102816* .6275/.6265 1-3/4 1.753/1.752 1 1/32
LC103016* .6275/.6265 1-7/8 1.878/1.877 1 1/32
PART FRACTION
NUMBER I.D. O.D. A C J
LC122414 .752/.751 1-1/2 1.503/1.502 7/8 1/32
LC122614* .752/.751 1-5/8 1.628/1.627 7/8 1/32
LC122816* .752/.751 1-3/4 1.753/1.752 1 1/32
LC123016* .752/.751 1-7/8 1.878/1.877 1 1/32
LC142816* .877/.876 1-3/4 1.753/1.752 1 1/32
LC143016* .877/.876 1-7/8 1.878/1.877 1 1/32
LC162816 1.002/1.001 1-3/4 1.753/1.752 1 1/32
LC163016* 1.002/1.001 1-7/8 1.878/1.877 1 1/32
LC164024* 1.002/1.001 2-1/2 2.503/2.502 1-1/2 1/32
LC164224* 1.002/1.001 2-5/8 2.628/2.627 1-1/2 1/32
LC204024* 1.252/1.251 2-1/2 2.503/2.502 1-1/2 1-32
LC204224* 1.252/1.251 2-5/8 2.628/2.627 1-1/2 1/32
LC244824* 1.503/1.501 3 3.003/3.001 1-1/2 1/32
LC245224* 1.503/1.501 3-1/4 3.253/3.251 1-1/2 1/32
LC285432* 1.753/1.751 3-3/8 3.380/3.378 2 1-32
LC285632* 1.753/1.751 3-1/2 3.505/3.503 2 1/32
LC325432* 2.004/2.001 3-3/8 3.380/3.378 2 1/32
LC325632* 2.004/2.001 3-1/2 3.505/3.503 2 1/32
Nylon
Sleeve (Plane) Bearings
PART NOMINAL DECIMAL
NUMBER I.D. O.D. I.D. O.D. LENGTH
95
Nylon
Sleeve (Plane) Bearings
NOMINAL DECIMAL
PART
NUMBER I.D. O.D. I.D. O.D. LENGTH
96
Nylon
Sleeve (Plane) Bearings
97
Nylon
Flange Bearings
98
Nylon
Flange Bearings
99
Nylon
Flange Bearings
Nylon
Thrust Bearings
100
Nylon
Thrust Bearings
101
Bunting PTFE Bearings and Bars
Bunting BJ4 (JLON® 4200), BJ5 (JLON® 5500), and BJ7 (JLON® 7000)
bar stock are manufactured from specially formulated PTFE compounds
machined to close tolerances. These materials provide a low coefficient
of friction, a broad temperature range, zero water absorption, and are
available in a wide range of standard sizes. Bunting PTFE bearings can
be utilized completely lubrication-free and have excellent wear
resistance. These bearings perform reliably and efficiently at extreme
temperatures, in corrosive environments, and in other demanding
applications.
BJ4 bearings and bars operate at PV values up to approximately
30,000 dry. Ideal for rotary and linear bearings, BJ4 eliminates the
need for lubrication in almost any environment. (JLON® 4200)
Temperature range: +550o F
BJ5 bearings and bars. Because it is polymer reinforced, BJ5
runs against soft mating surfaces such as mild steel, aluminum, and
SAE 316 stainless steel without the mating surface wear typically found
when other filled PTFE compounds are employed. (JLON® 5500)
Temperature range: +550o F
BJ7 bearings and bars. BJ7 material is made from a specially
formulated PTFE compound, designed for high load and wear resistance
in food and drug contact applications. All of the components of BJ7 are
FDA compliant and non-toxic. (JLON® 7000)
Temperature range: +550o F
BJ Liner bearings reduce material cost while being incredibly
versatile. Their improved load capacity is achieved by capturing a
minimum thickness of BJ tape inside a steel shell. (JLON® 4200 Tape
Liner)
Temperature range: -400o F/+550o F
PTFE
Sleeve (Plane) Bearings
PART PART PART RECOM- RECOM-
NUMBER NUMBER NUMBER NOMINAL DECIMAL MENDED MENDED
(BJ4S (BJ5S (BJ7S HOUSING SHAFT
PREFIX) PREFIX) PREFIX) I.D. O.D. LENGTH I.D. O.D. BORE SIZE
040602 040602 040602 1/4 3/8 1/4 .2540 .3760 .3750 .2500
040603 040603 040603 3/8 .2540 .3760 .3750 .2500
040604 040604 1/2 .2540 .3760 .3750 .2500
060903 060903 060903 3/8 9/16 3/8 .3790 .5630 .5625 .3750
060904 060904 1/2 .3790 .5630 .5625 .3750
060906 060906 3/4 .3790 .5630 .5625 .3750
081204 081204 081204 1/2 3/4 1/2 .5040 .7510 .7500 .5000
081206 081206 3/4 .5040 .7510 .7500 .5000
081208 081208 1 .5040 .7510 .7500 .5000
101405 101405 101405 5/8 7/8 5/8 .6300 .8760 .8750 .6250
101406 101406 3/4 .6300 .8760 .8750 .6250
101408 101408 101408 1 .6300 .8760 .8750 .6250
103
PTFE
Sleeve (Plane) Bearings
104
PTFE
Flange Bearings
030502 030502 3/16 5/16 1/4 .1910 .3130 .437 1/16 .3125 .1875
030504 030504 1/2
040603 040603 1/4 3/8 3/8 .2540 .3760 .500 1/16 .3750 .2500
040604 040604 040604 1/2
061004 061004 061004 3/8 5/8 1/2 .3790 .6260 .875 1/8 .6250 .3750
061006 061006 3/4
081204 081204 1/2 3/4 1/2 .5040 .7510 1.000 1/8 .7500 .5000
081206 081206 3/4
081208 081208 081208 1
101406 101406 5/8 7/8 3/4 .6300 .8760 1.000 1/8 .8750 .6250
101408 101408 101408 1
121608 121608 121608 3/4 1 1 .7550 1.0010 1.250 1/8 1.0000 .7500
162012 162012 162012 1 1- 1/4 1- 1/2 1.0050 1.2510 1.500 1/8 1.2500 1.0000
202416 202416 202416 1- 1/4 1- 1/2 2 1.2550 1.5010 1.750 1/8 1.5000 1.2500
242816 242816 242816 1- 1/2 1- 3/4 2 1.5060 1.7510 2.000 1/8 1.7500 1.5000
PTFE
Thrust Bearings
PART PART NOMINAL
NUMBER NUMBER I.D. O.D. THICKNESS I.D. O.D.
(BJ4T PREFIX) (BJ5T PREFIX) +.005/-.000 +.003/-.003 +.003 +.005/-.000" +.003/-.003"
041002 041002 1/4 5/8 1/16 .2540 .6250
061202 061202 3/8 3/4 1/16 .3790 .7500
081602 081602 1/2 1 1/16 .5040 1.0000
122204+ 122204+ 3/4 1- 3/8 1/8 .7550 1.3750
163204+ 163204+ 1 2 1/8 1.0050 2.0000
244804+ 244804+ 1- 1/2 3 1/8 1.5060 3.0000
+I.D. and O.D.: -.000/+.006"
105
PTFE
BJ Liner Bearings
PTFE
Solid Bars
O.D.
LG.
I.D. Tolerances
I.D. Dimension
From 1/4" to 3/4" ........................................................ +.000/-.002"
From 7/8" to 1-1/4" ..................................................... +.000/-.003"
From 1-3/8" to 5" ........................................................ +.000/-.004"
O.D. Tolerances
O.D. Dimension
Up to 7/8" .................................................................. +.000/-.001"
1" and up ................................................................... +.000/-.002"
Length Tolerances
I.D. up to and including 2-3/8" ........................................... +.005"
I.D. 2-1/2" up to and including 5" .............................. +.008/-.007"
107
PLANE THRUST
BEARINGS BEARINGS
Teflon® Composite
Sleeve (Plane) Bearings
PART RECOM- RECOM-
NUMBER NOMINAL DECIMAL MENDED MENDED
(BMT HOUSING PRESS SHAFT
PREFIX) I.D. O.D. I.D. O.D. BORE FIT SIZE
0810- 1/2 5/8 .5040 .6265 .6250 .0020 .4990
0812- 3/4 .7515 .7500 .0020 .4990
0816- 1 1.0025 1.0000 .0030 .4990
1012- 5/8 3/4 .6290 .7515 .7500 .0020 .6240
1014- 7/8 .8765 .8750 .0020 .6240
1018- 1-1/8 1.1275 1.1250 .0030 .6240
1214- 3/4 7/8 .7555 .8765 .8750 .0020 .7490
1216- 1 1.0025 1.0000 .0030 .7490
1220- 1-1/4 1.2525 1.2500 .0030 .7490
1416- 7/8 1 .8805 1.0025 1.0000 .0030 .8745
1418- 1-1/8 1.1275 1.1250 .0030 .8745
1422- 1-3/8 1.3785 1.3750 .0040 .8745
1618- 1 1-1/8 1.0055 1.1275 1.1250 .0030 .9990
1620- 1-1/4 1.2525 1.2500 .0030 .9990
1624- 1-1/2 1.5025 1.5000 .0030 .9990
1820- 1-1/8 1-1/4 1.1335 1.2525 1.2500 .0030 1.2480
1822- 1-3/8 1.3785 1.3750 .0040 1.1250
1826- 1-5/8 1.6285 1.6250 .0040 1.1250
2022- 1-1/4 1-3/8 1.2555 1.3785 1.3750 .0040 1.2490
2024- 1-1/2 1.5025 1.5000 .0030 1.2490
2028- 1-3/4 1.7535 1.7500 .0040 1.2490
2224- 1-3/8 1-1/2 1.3830 1.5025 1.5000 .0030 1.3745
2226- 1-5/8 1.6285 1.6250 .0040 1.3745
2230- 1-7/8 1.8785 1.8750 .0040 1.3745
2426- 1-1/2 1-5/8 1.5080 1.6285 1.6250 .0040 1.4995
2428- 1-3/4 1.7535 1.7500 .0040 1.4995
2432- 2 2.0035 2.0000 .0040 1.4995
2628- 1-5/8 1-3/4 1.6330 1.7535 1.7500 .0040 1.6245
2830- 1-3/4 1-7/8 1.7580 1.8785 1.8750 .0040 1.7495
2832- 2 2.0035 2.0000 .0040 1.7495
108
Teflon® Composite
Sleeve (Plane) Bearings
PART RECOM- RECOM-
NUMBER NOMINAL DECIMAL MENDED MENDED
(BMT HOUSING PRESS SHAFT
PREFIX) I.D. O.D. I.D. O.D. BORE FIT SIZE
2836- 2-1/4 2.2535 2.2500 .0040 1.7495
3234- 2 2-1/8 2.0080 2.1285 2.1250 .0040 1.9995
3236- 2-1/4 2.2535 2.2500 .0040 1.9995
3240- 2-1/2 2.5040 2.5000 .0045 1.9995
3640- 2-1/4 2-1/2 2.2580 2.5040 2.5000 .0045 2.2490
3644- 2-3/4 2.7540 2.7500 .0045 2.2490
3842- 2-3/8 2-5/8 2.3850 2.6290 2.6250 .0045 2.3750
3846- 2-7/8 2.8790 2.8750 .0045 2.3750
4044- 2-1/2 2-3/4 2.5100 2.7540 2.7500 .0045 2.4995
4048- 3 3.0040 3.0000 .0050 2.4995
4246- 2-5/8 2-7/8 2.6370 2.8790 2.8750 .0045 2.6245
4250- 3-1/8 3.1290 3.1250 .0050 2.6245
4448- 2-3/4 3 2.7620 3.0040 3.0000 .0050 2.7495
4452- 3-1/4 3.2540 3.2500 .0050 2.7495
4852- 3 3-1/4 3.0140 3.2540 3.2500 .0050 2.9995
4856- 3-1/2 3.5040 3.5000 .0050 2.9995
5256- 3-1/4 3-1/2 3.2640 3.5040 3.5000 .0050 3.2495
5260- 3-3/4 3.7540 3.7500 .0050 3.2495
5660- 3-1/2 3-3/4 3.5140 3.7540 3.7500 .0050 3.4995
5664- 4 4.0040 4.0000 .0050 3.4995
6064- 3-3/4 4 3.7640 4.0040 4.0000 .0050 3.7495
6068- 4-1/4 4.2540 4.2500 .0050 3.7495
6468- 4 4-1/4 4.0140 4.2540 4.2500 .0050 3.9995
6472- 4-1/2 4.5040 4.5000 .0050 3.9995
6872- 4-1/4 4-1/2 4.2640 4.5040 4.5000 .0050 4.2495
6876- 4-3/4 4.7540 4.7500 .0050 4.2495
7276- 4-1/2 4-3/4 4.5140 4.7540 4.7500 .0050 4.4995
7280- 5 5.0040 5.0000 .0050 4.4995
7680- 4-3/4 5 4.7640 5.0040 5.0000 .0050 4.7495
7684- 5-1/4 5.2540 5.2500 .0050 4.7495
8084- 5 5-1/4 5.0140 5.2540 5.2500 .0010 4.9985
8088- 5-1/2 5.5040 5.5000 .0050 4.9995
109
Bunting Teflon® Composite
Sleeve (Plane) Bearings
BMP bearings are designed for oscillatory and linear applications, offer
long wear, and are shaft kind.
For tolerance data, use BMT bearings tolerance information (see
page 107).
Temperature range: -212°F/+356°F
Consult Bunting for standard lengths available.
Teflon® Composite
Sleeve (Plane) Bearings
PART NOMINAL DECIMAL RECOM- RECOM-
NUMBER MENDED MENDED
(BMP HOUSING PRESS SHAFT
PREFIX) I.D. O.D. I.D. O.D. BORE FIT SIZE
0812- 1/2 3/4 .5040 .7515 .7500 .0020 .4995
1014- 5/8 7/8 .6290 .8765 .8750 .0020 .6245
1216- 3/4 1 .7555 1.0025 1.0000 .0030 .7495
1418- 7/8 1-1/8 .8805 1.1275 1.1250 .0030 .8745
1620- 1 1-1/4 1.0055 1.2525 1.2500 .0030 .9995
1822- 1-1/8 1-3/8 1.1335 1.3785 1.3750 .0040 1.1245
2024- 1-1/4 1-1/2 1.2555 1.5025 1.5000 .0030 1.2495
2226- 1-3/8 1-5/8 1.3830 1.6285 1.6250 .0040 1.3745
2428- 1-1/2 1-3/4 1.5080 1.7535 1.7500 .0040 1.4995
2832- 1-3/4 2 1.7580 2.0035 2.0000 .0040 1.7495
3236- 2 2-1/4 2.0080 2.2535 2.2500 .0040 1.9995
3240- 2 2-1/2 2.0080 2.5040 2.5000 .0045 1.9995
4044- 2-1/2 2-3/4 2.5100 2.7540 2.7500 .0045 2.4995
4048- 2-1/2 3 2.5100 3.0040 3.0000 .0050 2.4995
4852- 3 3-1/4 3.0140 3.2540 3.2500 .0050 2.9995
4856- 3 3-1/2 3.0140 3.5040 3.5000 .0050 2.9995
5664- 3-1/2 4 3.5140 4.0040 4.0000 .0050 3.4995
6472- 4 4-1/2 4.0140 4.5040 4.5000 .0050 3.9995
8088- 5 5-1/2 5.0140 5.5040 5.5000 .0050 4.9995
110
Teflon® Composite
Thrust Washers
PART PART
NUMBER NUMBER NOMINAL DECIMAL
.074" THK.* .078" THK.*
(BTCW (BTCWW
PREFIX) PREFIX) I.D. O.D. I.D. O.D.
0408-3 0408-3 1/4 1/2 .2640 .5000
0612-3 0612-3 3/8 3/4 .3890 .7500
0816-3 0816-3 1/2 1 .5130 1.0000
1020-3 1020-3 5/8 1-1/4 .6380 1.2500
1224-3 1224-3 3/4 1-1/2 .7640 1.5000
1428-3 1428-3 7/8 1-3/4 .8880 1.7500
1632-3 1632-3 1 2 1.0140 2.0000
1834-3 1834-3 1-1/8 2-1/8 1.1500 2.1250
2036-3 2036-3 1-1/4 2-1/4 1.2730 2.2500
2240-3 2240-3 1-3/8 2-1/2 1.3990 2.5000
2442-3 2442-3 1-1/2 2-5/8 1.5240 2.6250
2644-3 2644-3 1-5/8 2-3/4 1.6490 2.7500
2846-3 2846-3 1-3/4 2-7/8 1.7740 2.8750
3252-3 3252-3 2 3-1/4 2.0240 3.2500
3654-3 3654-3 2-1/4 3-3/8 2.2730 3.3750
4060-3 4060-3 2-1/2 3-3/4 2.5240 3.7500
4466-3 4466-3 2-3/4 4-1/8 2.7740 4.1250
4872-3 4872-3 3 4-1/2 3.0240 4.5000
111
PLANE
BEARINGS
RECOMMENDED INSTALLED
NOMINAL BEARING
PART HOUSING BORE SHAFT DIA. I.D.*
NUMBER I.D. O.D. LENGTH MIN. MAX. MIN. MAX. MIN. MAX.
02BU03 1/8 3/16 3/16 .1873 .1878 .1236 .1243 .1243 .1268
03BU03 3/16 1/4 3/16 .2497 .2503 .1858 .1865 .1867 .1893
03BU04 1/4
03BU08 1/2
04BU04 1/4 5/16 1/4 .3122 .3128 .2481 .2490 .2492 .2518
04BU06 3/8
05BU06 5/16 3/8 3/8 .3747 .3753 .3106 .3115 .3117 .3143
05BU08 1/2
06BU04 3/8 15/32 1/4 .4684 .4691 .3731 .3740 .3742 .3769
06BU06 3/8
06BU08 1/2
06BU10 5/8
06BU12 3/4
07BU08 7/16 17/32 1/2 .5309 .5316 .4355 .4365 .4367 .4394
07BU12 3/4
08BU04 1/2 19/32 1/4 .5934 .5941 .4980 .4990 .4992 .5019
08BU06 3/8
08BU08 1/2
08BU10 5/8
08BU12 3/4
08BU14 7/8
09BU08 9/16 21/32 1/2 .6559 .6566 .5605 .5615 .5617 .5644
09BU12 3/4
10BU08 5/8 23/32 1/2 .7184 .7192 .6230 .6240 .6242 .6270
10BU10 5/8
10BU12 3/4
10BU14 7/8
11BU14 11/16 25/32 7/8 .7809 .7817 .6855 .6865 .6867 .6895
12BU04 3/4 7/8 1/4 .8747 .8755 .7479 .7491 .7493 .7525
12BU06 3/8
12BU08 1/2
*When installed in a rigid steel or cast-iron housing.
112
"BU" Dry Lubricant Bearings
Inch Sizes
RECOMMENDED INSTALLED
NOMINAL BEARING
PART HOUSING BORE SHAFT DIA. I.D.*
NUMBER I.D. O.D. LENGTH MIN. MAX. MIN. MAX. MIN. MAX.
12BU10 3/4 7/8 5/8 .8747 .8755 .7479 .7491 .7493 .7525
12BU12 3/4
12BU16 1
14BU12 7/8 1 3/4 .9997 1.0005 .8729 .8741 .8743 .8775
14BU16 1
16BU08 1 1- 1/8 1/2 1.1247 1.1255 .9979 .9991 .9993 1.0025
16BU12 3/4
16BU16 1
16BU20 1- 1/4
16BU24 1- 1/2
18BU10 1- 1/8 1- 9/32 5/8 1.2808 1.2818 1.1226 1.1238 1.1240 1.1278
18BU12 3/4
18BU16 1
20BU12 1- 1/4 1-13/32 3/4 1.4058 1.4068 1.2472 1.2488 1.2490 1.2528
20BU16 1
20BU20 1- 1/4
20BU28 1- 3/4
22BU12 1- 3/8 1-17/32 3/4 1.5308 1.5318 1.3722 1.3738 1.3740 1.3778
22BU16 1
22BU24 1- 1/2
24BU08 1- 1/2 1-21/32 1/2 1.6558 1.6568 1.4972 1.4988 1.4990 1.5028
24BU16 1
24BU20 1- 1/4
24BU24 1- 1/2
24BU32 2
26BU16 1- 5/8 1-25/32 1 1.7808 1.7818 1.6222 1.6238 1.6240 1.6278
26BU24 1- 1/2
28BU16 1- 3/4 1-15/16 1 1.9371 1.9381 1.7471 1.7487 1.7489 1.7535
28BU24 1- 1/2
30BU16 1- 7/8 2- 1/16 1 2.0621 2.0633 1.8721 1.8737 1.8739 1.8787
32BU16 2 2- 3/16 1 2.1871 2.1883 1.9969 1.9987 1.9989 2.0037
32BU24 1- 1/2
32BU28 1- 3/4
32BU32 2
32BU40 2- 1/2
*When installed in a rigid steel or cast-iron housing.
Length Tolerances:
Up to and including 3/8" I.D. .......................................... + 0.015"
Above 3/8" I.D. ................................................................ + 0.010"
113
"BU" Dry Lubricant Bearings
Metric Sizes
RECOMMENDED INSTALLED
NOMINAL BEARING
PART HOUSING BORE SHAFT DIA. I.D.*
NUMBER I.D. O.D. LENGTH MIN. MAX. MIN. MAX. MIN. MAX.
M0303BU 3.00 4.50 3.00 4.5000 4.5080 2.9940 3.0000 3.0000 3.0480
M0305BU 5.00
M0306BU 6.00
M0404BU 4.00 5.50 4.00 5.5000 5.5080 3.9920 4.0000 4.0000 4.0480
M0406BU 6.00
M0410BU 10.00
M0505BU 5.00 7.00 5.00 7.0000 7.0150 4.9780 4.9900 4.9900 5.0550
M0508BU 8.00
M0510BU 10.00
M0606BU 6.00 8.00 6.00 8.0000 8.0150 5.9780 5.9900 5.9900 6.0550
M0608BU 8.00
M0610BU 10.00
M0710BU 7.00 9.00 10.00 9.0000 9.0150 6.9720 6.9870 6.9900 7.0550
M0808BU 8.00 10.00 8.00 10.0000 10.0150 7.9720 7.9870 7.9900 8.0550
M0810BU 10.00
M0812BU 12.00
M1010BU 10.00 12.00 10.00 12.0000 12.0180 9.9720 9.9870 9.9900 10.0580
M1012BU 12.00
M1015BU 15.00
M1020BU 20.00
M1208BU 12.00 14.00 8.00 14.0000 14.0180 11.9660 11.9840 11.9900 12.0580
M1210BU 10.00
M1212BU 12.00
M1215BU 15.00
M1220BU 20.00
M1225BU 25.00
M1310BU 13.00 15.00 10.00 15.0000 15.0180 12.9660 12.9840 12.9900 13.0580
M1415BU 14.00 16.00 15.00 16.0000 16.0180 13.9660 13.9840 13.9900 14.0580
M1420BU 20.00
M1512BU 15.00 17.00 12.00 17.0000 17.0180 14.9660 14.9840 14.9900 15.0580
M1515BU 15.00
M1525BU 25.00
M1612BU 16.00 18.00 12.00 18.0000 18.0180 15.9660 15.9840 15.9900 16.0580
M1615BU 15.00
M1620BU 20.00
M1625BU 25.00
M1720BU 17.00 19.00 20.00 19.0000 19.0210 16.9660 16.9840 16.9900 17.0610
M1815BU 18.00 20.00 15.00 20.0000 20.0210 17.9660 17.9840 17.9900 18.0610
M1820BU 20.00
M1825BU 25.00
M2015BU 20.00 23.00 15.00 23.0000 23.0210 19.9590 19.9800 19.9900 20.0620
M2020BU 20.00
*When installed in a rigid steel or cast-iron housing.
114
"BU" Dry Lubricant Bearings
Metric Sizes
RECOMMENDED INSTALLED
NOMINAL BEARING
PART HOUSING BORE SHAFT DIA. I.D.*
NUMBER I.D. O.D. LENGTH MIN. MAX. MIN. MAX. MIN. MAX.
M2025BU 20.00 23.00 25.00 23.0000 23.0210 19.9590 19.9800 19.9900 20.0620
M2030BU 30.00
M2215BU 22.00 25.00 15.00 25.0000 25.0210 21.9590 21.9800 21.9900 22.0710
M2220BU 20.00
M2225BU 25.00
M2420BU 24.00 27.00 20.00 27.0000 27.0210 23.9590 23.9800 23.9900 24.0710
M2425BU 25.00
M2430BU 30.00
M2515BU 25.00 28.00 15.00 28.0000 28.0210 24.9590 24.9800 24.9900 25.0710
M2520BU 20.00
M2525BU 25.00
M2530BU 30.00
M2550BU 50.00
M2820BU 28.00 32.00 20.00 32.0000 32.0250 27.9590 27.9800 27.9900 28.0850
M2830BU 30.00
M3020BU 30.00 34.00 20.00 34.0000 34.0250 29.9590 29.9800 29.9900 30.0850
M3025BU 25.00
M3030BU 30.00
M3040BU 40.00
M3240BU 32.00 36.00 40.00 36.0000 36.0250 31.9500 31.9750 31.9900 32.0850
M3520BU 35.00 39.00 20.00 39.0000 39.0250 34.9500 34.9750 34.9900 35.0850
M3530BU 30.00
M3550BU 50.00
M4020BU 40.00 44.00 20.00 44.0000 44.0250 39.9500 39.9750 39.9900 40.0850
M4030BU 30.00
M4040BU 40.00
M4050BU 50.00
M4530BU 45.00 50.00 30.00 50.0000 50.0250 44.9500 44.9750 44.9900 45.1050
M4550BU 50.00
M5040BU 50.00 55.00 40.00 55.0000 55.0300 49.9500 49.9750 49.9900 50.1100
M5060BU 60.00
Length Tolerances:
Up to and including 10 mm I.D. ................................. + 0.38 mm
Above 10 mm I.D. ....................................................... + 0.25 mm
115
Bunting VESPEL®
Bearings
VESPEL® - Top of the line machined and Vespel® bearings provide
capabilities of high speed, load, and temperature. Bunting Bearings
offers a wide range of sizes as standard off-the-shelf, along with a full
range of special, made to order sizes.
Vespel® bearings are made from polyimide resins to combine the
best characteristics of plastics, metals, and ceramics. Vespel® resist
wear and fight creep; properties that allow them to survive a broad
range of conditions, particularly where elevated speeds and high loads
present problems.
Precision machined sizes hold close tolerances.
Tolerances:
Sleeve (Plane) Bearings
I.D. and O.D .................................................................. +.000/-.001"
Length ..................................................................................... +.005"
Flange Bearings
I.D. and O.D. ................................................................. +.000/-.001"
Length ..................................................................................... +.005"
Flange O.D. ............................................................................ +.005"
Flange Thickness ................................................................... +.003"
Thrust Bearings
I.D. ................................................................................ +.010/-.000"
O.D. ......................................................................................... +.005"
Thickness ................................................................................ +.003"
116
VESPEL®
Sleeve (Plane) Bearings
Precision Machined
PART RECOMMONDED
NUMBER I.D. O.D. LENGTH HOUSING BORE
3/16 X 5/16 NOMINAL
BVS030504 .1920 .3145 1/4 .3125
BVS030506 3/8
BVS030508 1/2
1/4 X 5/16 NOMINAL
BVS040504 .2555 .3145 1/4 .3125
BVS040512 3/4
1/4 X 3/8 NOMINAL
BVS040604 .2555 .3770 1/4 .3750
BVS040606 3/8
BVS040608 1/2
BVS040612 3/4
BVS040616 1
1/4 X 7/16 NOMINAL
BVS040706 .2560 .4400 3/8 .4375
5/16 X 3/8 NOMINAL
BVS050608 .3190 .3770 1/2 .3750
5/16 X 7/16 NOMINAL
BVS050708 .3195 .4400 1/2 .4378
5/16 X 1/2 NOMINAL
BVS050806 .3195 .5025 3/8 .5000
BVS050812 3/4
3/8 X 1/2 NOMINAL
BVS060804 .3825 .5025 1/4 .5000
BVS060806 3/8
BVS060808 1/2
BVS060810 5/8
BVS060812 3/4
BVS060816 1
BVS060820 1-1/4
3/8 X 9/16 NOMINAL
BVS060906 .3825 .5650 3/8 .5625
3/8 X 5/8 NOMINAL
BVS061012 .3830 .6280 3/4 .6250
1/2 X 5/8 NOMINAL
BVS081006 .5095 .6280 3/8 .6250
BVS081008 1/2
BVS081010 5/8
BVS081012 3/4
117
VESPEL®
Sleeve (Plane) Bearings
Precision Machined
PART RECOMMONDED
NUMBER I.D. O.D. LENGTH HOUSING BORE
VESPEL®
Flange Bearings
Precision Machined
118
VESPEL®
Flange Bearings
Precision Machined
VESPEL®
Thrust Bearings
Precision Machined
PART
NUMBER I.D. O.D. LENGTH
1/4 X 1/2 NOMINAL
BVT040801 .2560 .5000 1/16
3/8 X 5/8 NOMINAL
BVT061001 .3830 .6250 1/16
3/8 X 3/4 NOMINAL
BVT061201 .3830 .7500 1/16
1/2 X 3/4 NOMINAL
BVT081201 .5100 .7500 1/16
119
VESPEL®
Thrust Bearings
Precision Machined
PART
NUMBER I.D. O.D. THICKNESS
1/2 X 1 NOMINAL
BVT081601 .5100 1.0000 1/16
BVT081602 1/8
5/8 X 1 NOMINAL
BVT101601 .6360 1.0000 1/16
BVT101602 1/8
5/8 X 1- 1/4 NOMINAL
BVT102002 .6360 1.2500 1/8
3/4 X 1- 1/4 NOMINAL
BVT122001 .7630 1.2500 1/16
BVT122002 .7630 1.2500 1/8
1 X 1- 1/2 NOMINAL
BVT162402 1.0170 1.5000 1/8
1 X 2 NOMINAL
BVT163202 1.0170 2.0000 1/8
1- 1/4 X 2 NOMINAL
BVT203201 1.2680 2.0000 1/16
120
BUNTING BEARINGS CORP.
MANUFACTURING LOCATIONS
Delta, Ohio 43515
200 Van Buren St.
P.O. Box 37
419-866-7000/FAX 419-866-0653
Holland, Ohio 43528
1001 Holland Park Blvd.
P.O. Box 729
419-866-7000/FAX 419-866-0653
Kalamazoo, Michigan 49002
4252 E. Kilgore Road
269-345-8691/FAX 269-345-0931
Mansfield, Ohio 44902
153 E. Fifth St.
P.O. Box 1053
419-866-7000/FAX 419-522-6011
CORPORATE HEADQUARTERS
Holland, Ohio 43528
1001 Holland Park Blvd.
P.O. Box 729
419-866-7000/FAX 419-866-0653
E-mail: bunting@buntingbearings.com
Internet: www.buntingbearings.com
DISTRIBUTED BY:
MOUNTED BEARINGS
"Quality and Service"
The Bunting Commitment to
World Class Partnering