Professional Documents
Culture Documents
FLAT PRODUCTS:
A) HR COILS, SHEETS & SKELP
Hot Rolled Coils, Sheets and Skelp
Rationalised sizes of Hot Rolled Coils(Rourkela Steel Plant)
Thickness
(mm)
Width (mm)
2.0
2.2
2.3
2.5
2.8
3.1
3.5
3.7
4.1
6.6, 7.4
7, 8, 9, 10
Coils can also be supplied in other width/thickness combination, as per mutual agreement.
Inner diameter of coils : 760 mm. Coil weight : 8 -17 tonnes
Bokaro Steel Plant
Rationalised sizes of Hot Rolled Coils
Thickness
(mm)
Width (mm)
1.8
930, 1030
2.0
2.2
2.5
2.8
3.0
3.5
3.9
4.3
4.6
4.8
5.0
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
5.6
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730
6.0
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
6.7
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
7.0
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
8.0
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
8.6
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
9.7
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
10
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
930, 1030, 1130*, 1250, 1310, 1370, 1400, 1420, 1550, *1730, *1830
* through cc route
1100 mm width as already indicated will be through concast route for which sequential order will be required.
Coils can also be supplied in other sizes, as per mutual agreement.
Inner diameter of coils : 850 mm
Outer diameter of coils : 2300 mm (max)
Coil weight : 29 tonnes max.
Bokaro Steel Plant
Rationalised sizes of Hot Rolled Sheets
Thickness, mm (gauge)
Width (mm)
Length (mm)
2.00 mm (14)
1000, 1250
2500
1000, 1250,
2500, 4000
Thickness and width tolerances are as per IS: 1852/1985. Closer tolerances can also be supplied on demand.
Packaging : Bare bundles with cross-wise steel strip. Packet weight : 7 - 18 tonnes. Marking : Paint marked on the top sheet
of the bundle OR Sticker/label on top sheet of bundle with required details.
Common grades for Hot Rolled Coils and Sheets : IS 10748/1995 grades I-V, API 5L Grades A, B, X42, X46, X52, X56,
X60, SAIL-WTCR, IS: 11513/1985 grades O, D, DD, EDD, IS: 1079/ 1994 grades O, D, DD, EDD, Medium Carbon Strapping
Steel, MC-40, MC-5, HCRS, SAE-1040, SAE 1055, C 30, 40, 50, Medium Silicon Electrical Steel, IS: 6240/1999, SAIL HS
LPG, SAILMA, IS: 2062, 2006, IS: 5986/1992 Fe 330, 360, 410, 510, SAILRIM, IS: 2062/2006 Grade with copper,
SAILCOR/IRSM-41, SAE 1012, SAE 1541 Auto Chassis Grade: E 34 / E38 / 46& SAPH 45.
Materials are also available in the following foreign specifications : For structural and general purposes- ASTM-A 36/A
569/A 570 Grades 33/40, JISG 3101 SS400, JISG 3131 SPHC, DIN 17100 ST 37.2/ST 44.2, BS 4360 Grades 40/43A, EN
10025; For Tube-making and other grades : JISG 3132 SPHT 1/2, DIN 1614 Pt. 1/2 ST 22/23/24, SAE 1006, SAE 1018 or
equivalents, if sufficient orders are available.
Width (mm)
Length (mm)
2.9
1240
2480
2.8
1250
2500
Sheets can also be supplied in the following sizes on mutual agreement : 2.9 x 1360 x 2720 mm, 2.9 x 1270 x 2540 mm, 3.0 x
1360 x 2700 mm Other sizes of hot rolled coils and sheets can be supplied as per mutual agreement.
HR Coils for LPG Cylinders
Thickness
(mm)
Grade
Width (mm)
Conventional (IS:
6240/1999)
2.9
1090, 1160,
1250, 1685
2.2 - 4.0
1090, 1160,
1250
Thickness (mm)
147
166
2.5, 3.0
181
4.1, 4.3
184
196
205
210
230
232
234
Any customised dimension of width 147 mm to 252 mm and thickness 2.5 mm to 4.5 mm can be supplied as per mutual
agreement.
Coil weight : 0.88 - 1.24 tonnes
Inner diameter : 550 mm Outer diameter : 1100 - 1300 mm
Common Grades : Skelp is produced in IS 10748/1995, Grades I, II (Sk), IS 11513/1985 and Medium Carbon.
Packing : Bare packing with 4 steel straps through coil eye.
Tags : Cast details, specifications, etc.
Application
Tube making
SAILRIM
SAE 1012
SAILMA, IS 2062/2006,Grades B, C, IS
5986/1992* Fe 330, 360, 410, 510
SAE 1541
IS 6240/2008
Fabrication of long & cross members for LCV, MCV and HCV
Long and cross member of LCV & MCV,wheel disc, wheel rim and
other structural components of passenger car
Manufacture of tubes & pipes mostly for oil and gas sector
Tolerance (mm)
Up to 250
+ 4, - 0
+ 6, - 0
+ 10, - 0
+ 30, - 0
+ 35, - 0
+ 40, - 0
Width (mm)
Upto 200
0.20
0.23
0.25
0.30
> 2 to 3
> 3 to 5
> 5 to 8
>8
to 10
500 to
1250
0.18
0.20
0.25
0.30
0.35
1250 to
1550
0.20
0.25
0.30
0.35
0.40
1550 to
1850
0.22
0.28
0.35
0.40
0.40
Rolling and Cutting Tolerance for HR Sheets as per IS: 1852 - 1985
Width
(mm)
Tolerance
(mm)
Length
(mm)
Tolerance
Up to 125 0 + 6 , - 0
Up to
2500
> 1250 to
+ 0.5%, - 0
1550
+ 1% of the length
Over 2500 (max 70 mm), - 0
mm
+ 25 mm, - 0 mm
Tolerance
Up to 1.25
9%
1.25 to 1.6
8%
1.6 to 4.0
7%
Note : Cutting tolerance for all lengths for all products except plate, strip and sheet shall be + 100 mm, - 0 mm.
Closer tolerances can be supplied on mutual agreement.
Chemical Composition
Specification
C%
max
Grade
IS:
10748/1995
Mn %
max
P%
max
S%
max
0.10
0.50
0.040
0.040
II
0.12
0.60
0.040
0.040
III
0.16
1.20
0.040
0.040
IV
0.20
1.30
0.040
0.040
0.25
1.30
0.040
0.040
Specification
0.25
C%
max
Grade
SAIL SOFT
Si % max
0.06
0.025
Mn % max
0.25
0.025
0.04
P%
max
0.025
S % max
0.04
B max
30 ppm
Quality
Quality Old
Designation Designation
Quality
Name
HR0
(New)
Ordinary
HR1
HR2
Tensile
Strength
Rm2
max MPa
Percentage
Elongation
after
Fracture
A3,4 min
.t<3: Gauge
length
Lo=80 mm
Percentage
Elongation
after
Fracture A3,
4 min.t<3:
Gauge
length
Lo=50 mm
Percentage
Elongation
after
Fracture
A3,4
min.t<3:
Gauge
length
Lo=5.65
mm
Percentage
Elongation
after
Fracture
A3,4
min.t<3:
Gauge
length
Lo=50 mm
Commercial 440
23
24
28
29
Drawing
420
25
26
30
31
HR3
DD
Deep
Drawing
400
28
29
33
34
HR4
EDD
Extra Deep
380
Drawing
31
32
36
37
HR6
400-500
26
27
450-570
24
25
500-620
20
21
NOTES:
1. 1 MPa = 1N/mm2
2. Minimum tensile strength for qualities HR1, HR2, HR3 and HR4 would normally be expected to be 270 MPa. Where
minimum tensile strength is required, the value of 270 MPa may be specified. All tensile strength values are determined to the
nearest 10 MPa.
3. The non proportional test piece with a fixed original gauge length (50 mm) up to 6 mm thick sheet can be used in
conjunction with a conversion table. In case of dispute, however, only the results obtained on a proportional test piece will be
valid for material 3 mm and over in thickness.
4. HR5 grade is for cold rolling only, therefore mechanical properties are not applicable.
5. Where t is thickness of steel sheet, in mm.
6. Tensile testing is not mandatory for HR1, unless agreed to between the purchaser and manufacturer.
* Properties on mutual agreement between the purchaser and manufacturer.
Old
Designation
Designation
Name
Microalloy
HR0
(New)
Ordinary
0.25
1.70
0.05
0.045
HR1
Commercial
0.15
0.60
0.05
0.035
HR2
Drawing
0.10
0.45
0.040
0.035
HR3
DD
Deep Drawing
0.08
0.40
0.035
0.030
HR4
EDD
Extra Deep
Drawing
0.08
0.35
0.030
0.030
HR6
0.16
1.6
0.020
0.020
0.20 Si=0.4
max
NOTES:
1. Steel of these grades can be supplied with the addition of micro-alloying elements like Boron, Titanium, Niobium and
Vanadium. The micro-alloying elements shall not exceed 0.008 percent in case of Boron and 0.20 percent in case of other
elements.
2. The Nitrogen content of the steel shall not be more than 0.007 percent. For Aluminium killed or Silicon-Aluminium killed, the
Nitrogen content shall not exceed 0.012 percent. This has to be ensured by the manufacturer by occasional check analysis.
3. Grade HR4 and HR5 shall be supplied in fully Aluminium killed condition or Aluminium with stabilising elements.
4. When the steel is Aluminium killed, the total Aluminium content shall not be less than 0.02 percent. When the steel is Silicon
killed, the Silicon content shall not be less than 0.10 percent. When the steel is Aluminium-Silicon killed, the Silicon content
shall not be less than 0.03 percent and total Aluminium content shall not be less than 0.01 percent.
5. When Copper bearing steel is required the Copper content shall be between 0.20 and 0.35 percent. In case of product
analysis, the Copper content shall be between 0.17 and 0.38 percent.
6. Restricted chemistry may be mutually agreed to between the purchaser and the supplier.
7. IF denotes Interstitial Free and IF-HS denotes High Strength Interstitial Free.
8. * denotes that dual phase steel may also content Cr and Mo up to 1.0 percent.
Specification
SAIL DRAW
Grade
EDD (CBT)
C % max
Mn % max
P % max
S % max
0.04
0.15
0.015
0.015
SAIL RIM
0.07-0.11
0.30-0.45
0.040
0.040
SAE 1012
0.10-0.15
0.30-0.60
0.030
0.035
SAIL PROP
SAE 1020
0.17-0.23
0.32-0.6
0.04
0.03
SAIL PREFAB
0.23 max
1.35 max
0.04
0.03
Si % max
0.03 Al: 0.025-0.06
0.10 max
Nb: 0.005-0.05
Ladle
Analysis
% Max
S
Ladle
Analysis
% Max
P
Ladle
Analysis
% Max
S1
Carbon
Equivalent
(CE) Max
Method of
Deoxidation
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
E 250
0.23
1.50
0.045
0.045
0.40
0.42
Semi
Killed/Killed
E 250
BR
BO
0.22
1.50
0.045
0.045
0.40
0.41
Killed
E 250
0.20
1.50
0.040
0.040
0.40
0.39
Killed
E 300
0.20
1.30
0.045
0.045
0.45
0.40
Semi
Killed/Killed
E 300
BR
0.20
1.30
0.045
0.045
0.45
0.40
Killed
E 300
BO
0.20
1.30
0.045
0.045
0.45
0.40
Killed
E 300
0.20
1.30
0.045
0.045
0.45
0.40
Killed
E 350
0.20
1.50
0.045
0.045
0.45
0.42
Semi
Killed/Killed
E 350
BR
0.20
1.50
0.045
0.045
0.45
0.42
Killed
E 350
BO
0.20
1.50
0.045
0.045
0.45
0.42
Killed
E 350
0.20
1.50
0.045
0.045
0.45
0.42
Killed
E 410
0.20
1.60
0.045
0.045
0.45
0.46
Semi
Killed/Killed
E 410
BR
0.20
1.60
0.045
0.045
0.45
0.46
Killed
E 410
BO
0.20
1.60
0.045
0.045
0.45
0.46
Killed
E 410
0.20
1.60
0.045
0.045
0.45
0.46
Killed
E 450
0.22
1.60
0.045
0.045
0.45
0.48
Semi
Killed/Killed
E 450
BR
0.22
1.60
0.045
0.045
0.45
0.48
Killed
E 550
0.22
1.65
0.020
0.025
0.50
0.50
Semi
Killed/Killed
E 550
BR
0.22
1.65
0.020
0.025
0.50
0.50
Killed
E 600
0.22
1.70
0.020
0.025
0.50
0.50
Semi
Killed/Killed
E 600
BR
0.22
1.70
0.020
0.025
0.50
0.50
Killed
E 650
0.22
1.70
0.015
0.025
0.50
0.52
Semi
Killed/Killed
E 650
BR
0.22
1.70
0.015
0.025
0.50
0.52
Killed
Specification
SAIL COR
Grade
IRSM 41
C%
max
0.10
Mn %
max
0.25-0.45
P%
max
0.750.140
S%
max
0.030
Cr 0.35-0.60, Ni
0.20-0.47, Cu 0.300.60, Al 0.03 max
HCRS (Cu-P)
Si % max
0.28-0.72
Cr 0.35-0.60, Ni 0.20-0.47,
Cu 0.30-0.60, Al 0.03 max
0.15
0.25-0.8
0.07-0.15 0.03
IS 5986/1992
Fe 330
0.17
1.00
0.045
0.045
Fe 360
0.17
1.20
0.045
0.045
Fe 410
0.20
1.30
0.045
0.045
Fe 510
0.20
1.50
0.045
0.045
300
0.25
1.50
0.055
0.055
300 HI
0.20
1.50
0.040
0.040
350
0.25
1.50
0.040
0.040
350 HI
0.20
1.50
0.040
0.040
Nb+V+Ti
0.30%
max
* under revision
Mechanical Properties
Specification
Grade
C%
max
Mn %
max
P%
max
S%
max
Si % max
Al % min
0.250.45
1.201.45
0.040
0.040
0.15-0.35
0.360.44
1.301.60
0.030
0.030
0.15-0.35
SAIL MC 30
0.260.35
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 40
0.360.45
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 45
0.410.50
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 50
0.460.55
0.600.90
0.40
0.04
0.15-0.35
0.02
SAIL MC 55
0.510.60
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 60
0.560.65
0.600.90
0.04
0.04
0.15-0.35
0.02
Medium Si Electrical
Steel
0.05
0.40
0.025
0.025
0.30 - 1.50
IS 6240/1999
0.16
0.30
min
0.025
0.025
0.025 Al
0.02 min
SG 255
0.20
max
0.30
min
0.04
0.040
SG 295
0.20
max
0.10
max
0.04
0.040
0.35
P265NB
0.19
max
0.40
min
0.025
0.015
0.25
P310NB
0.20
max
0.70
min
0.025
0.015
0.50
SAIL MC 30
0.260.35
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 40
0.360.45
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 45
0.410.45
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 50
0.460.55
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 55
0.510.60
0.600.90
0.04
0.04
0.15-0.35
0.02
SAIL MC 60
0.560.65
0.600.90
0.04
0.04
0.15-0.35
0.02
0.14
1.2
0.015
0.010
0.15
0.22
0.9
0.030
0,030
0.26
1.20
0.030
0.030
X42
0.26
1.30
0.030
0.030
X46
0.26
1.40
0.030
0.030
X52
0.26
1.40
0.030
0.030
X56
0.26
1.40
0.030
0.030
Strapping Quality
IRS P 41
SAE 1541
SAIL HS LPG
JISG 3116
SAIL HS LPG
EN 10120
Nb 0.05 max Ti
0.03.030
IS 1079
X60
0.26
1.40
0.030
0.030
X65
0.26
1.45
0.030
0.030
X70
0.26
1.65
0.030
0.030
Nb +V + Ti < 0.15%
Mechanical Properties
Specification Grade
IS:
10748/1995
Yield
Strength MPa
min
Ultimate Tensile
Strength MPa min
Elongation %(Up to
Above 3 mm 3 mm)
Internal diameter of
bend
170
290
30
II
210
330
28
2T
III
240
410
25
2T
IV
275
430
20
3T
310
490
15
3T HRB
SAIL WTCR
35
65 max Hardness
SAIL SOFT
38
55 HRB max
Quality
Quality Old
Designation Designation
Quality
Name
Tensile
Strength
Rm2
max MPa
Percentage
Elongation
after
Fracture
A3,4 min
.t<3: Gauge
length
Lo=80 mm
Percentage
Elongation
after
Fracture A3,
4 min.t<3:
Gauge
length
Lo=50 mm
Percentage
Elongation
after
Fracture
A3,4
min.t<3:
Gauge
length
Lo=5.65
mm
Percentage
Elongation
after
Fracture
A3,4
min.t<3:
Gauge
length
Lo=50 mm
HR0
(New)
Ordinary
HR1
Commercial 440
23
24
28
29
HR2
Drawing
420
25
26
30
31
HR3
DD
Deep
Drawing
400
28
29
33
34
HR4
EDD
Extra Deep
380
Drawing
31
32
36
37
HR6
400-500
26
27
450-570
24
25
500-620
20
21
NOTES:
1. 1 MPa = 1N/mm2
2. Minimum tensile strength for qualities HR1, HR2, HR3 and HR4 would normally be expected to be 270 MPa. Where
minimum tensile strength is required, the value of 270 MPa may be specified. All tensile strength values are determined to the
nearest 10 MPa.
3. The non proportional test piece with a fixed original gauge length (50 mm) up to 6 mm thick sheet can be used in
conjunction with a conversion table. In case of dispute, however, only the results obtained on a proportional test piece will be
valid for material 3 mm and over in thickness.
4. HR5 grade is for cold rolling only, therefore mechanical properties are not applicable.
5. Where t is thickness of steel sheet, in mm.
6. Tensile testing is not mandatory for HR1, unless agreed to between the purchaser and manufacturer.
* Properties on mutual agreement between the purchaser and manufacturer.
Specificati
on
Grade
Yield
Strength
MPa min
Ultimate Tensile
Strength MPa
min
Elongation %(Up to 3
mm Above 3 mm)
Internal
diameter of bend
SAIL DRAW
SAIL RIM
SAE 1012
SAIL PROP
SAE 1020
310-320
440
15
SAIL PRE
FAB
345 min
450 min
21
Grade
Designat
ion
Quality
Tensile
Strengt
h Rm
Min
Mpa
Yield
Stress
Min
Mpa
<20
Yield
Stres
s Min
Mpa
20
Yield
Stress
Min
Mpa 40
Percentag
e
Elongatio
n A at
Gauge
Length
L=5.65
VS Min
>40
Interna
l Bend
Diamet
er Min
(See
Note 2)
<25
Interna
l Bend
Diamet
er Min
(See
Note
2)>25
Charpy Charpy
Impact Impact
Test(Se Test(Se
e Note
e Note
3 & 4)
3 & 4)
Temp
Min
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
E-250
410
250
240
230
23
2t
3t
E-250
BR
410
250
240
230
23
2t
3t
RT
27
E-250
BO
410
250
240
230
23
2t
3t
27
E-250
410
250
240
230
23
2t
3t
(-)20
27
E-300
440
300
290
280
22
2t
E-300
BR
440
300
290
280
22
2t
RT
27
E-300
BO
440
300
290
280
22
2t
27
E-300
440
300
290
280
22
2t
(-)20
27
E-350
490
350
330
320
22
2t
E-350
BR
490
350
330
320
22
2t
RT
27
E-350
BO
490
350
330
320
22
2t
27
E-350
490
350
330
320
22
2t
(-)20
27
E-410
540
410
390
380
20
2t
E-410
BR
540
410
390
380
20
2t
RT
25
E-410
BO
540
410
390
380
20
2t
25
E-410
540
410
390
380
20
2t
(-)20
25
E-450
570
450
430
420
20
2.5t
E-450
BR
570
450
430
420
20
2.5t
RT
20
E-450
BO
570
450
430
420
20
2.5t
20
E-450
570
450
430
420
20
2.5t
(-)20
20
E-550
650
550
530
520
12
3.0t
E 600
730
600
580
570
12
3.5t
E 600
BR
730
600
580
570
12
3.5t
RT
15
E 650
780
650
630
620
12
4.0t
E 650
BR
780
650
630
620
12
4.0t
RT
15
Specification
Strapping
Quality
SAE 1541
Grade
Yield
Strength MPa
min
Ultimate Tensile
Strength MPa
Elongation %(Up to
3 mm Above 3 mm)
Internal diameter of
bend
Medium Carbon C 30
55% of UTS
500-600
21
C 40
580-680
18
C 50
660-780
13
350-450
25
Med Si Elec
IS 6240/12008
240
SAIL HS LPG
SG 255 255
400
28
JISG 3116
SG 295 295
450
26
SAIL HS LPG
P265NB 265
410-500
24
EN 10120
P310NB 310
460-550
28
Quality
Quality Old
Designation Designation
Quality
Name
HR0
(New)
Ordinary
HR1
HR2
Tensile
Strength
Rm2
max MPa
Percentage
Elongation
after
Fracture A3,
4 min.t<3:
Gauge
length
Lo=50 mm
Percentage
Elongation
after
Fracture
A3,4
min.t<3:
Gauge
length
Lo=5.65
mm
Percentage
Elongation
after
Fracture
A3,4
min.t<3:
Gauge
length
Lo=50 mm
Commercial 440
23
24
28
29
Drawing
420
25
26
30
31
HR3
DD
Deep
Drawing
400
28
29
33
34
HR4
EDD
Extra Deep
380
Drawing
31
32
36
37
HR6
400-500
26
27
450-570
24
25
500-620
20
21
Specification
Grade
Percentage
Elongation
after
Fracture
A3,4 min
.t<3: Gauge
length
Lo=80 mm
Yield
Strength
MPa min
Ultimate Tensile
Strength MPa min
304 (1<6
JISG 3113
mm) 294
SAPH 45/440 (t:6-8
mm)
441
APL-5L
331
207
241-418
414-758
X42
290-496
414-758
X46
317-524
434-758
X52
359-531
455-758
X56
386-544
490-758
X60
414-565
517-758
X65
448-600
531-758
X70
483-621
565-758
Elongation %(Up
to 3 mm Above 3
mm)
Internal diameter of
bend
% elongation 1.944A
0.2/U 0.9 (GL: 50.8
mm)for all API Grades
A: Cross sectional
area in mm2
U: Minimum UTS in
MPa
NOTES: These are pipe properties. Hot rolled plate/coil properties are to be mutually agreed upon by producer and pipe
manufacturers.
Stainless Steel
Thickness
1.6 - 12.70 mm
2.0 - 8.0 mm
Width
1000 - 1275 mm
1000 - 1275 mm
Coil ID
762/610 mm
762/610 mm
Condition
As rolled
As rolled
Edge
Mill Edge
Mill Edge
Thickness Range
(mm)1.6-2.0
>2.0-3.0
>3.0-5.0
>5.0-8.0
>8.0-10.0
>10.0-12.7
1000-1250
0.18
0.20
0.25
0.30
0.35
0.50
> 1250-1275
0.20
0.25
0.30
0.35
0.40
0.50
* Thickness measurements are taken at 20 mm from the edge.Standard Product Tolerance : Hot Rolled Stainless Steel
Thickness Tolerance (For all width ranges)
Thickness (mm)
Tolerance (mm)
2.00
0.18
2.25
0.20
2.50
0.23
3.00
0.25
3.50
0.30
4.00
0.36
5.00
-0.25, +0.47
6.00
- 0.25, +0.51
- 0.25, +0.75
For specified thickness other than those shown, the tolerance for the next higher thickness shall apply.
Thickness measurements are taken at least 15 mm from the edge for Trimmed Edge (TE) and 25 mm from the
edge for Mill Edge (ME) products.
Stainless Steels:
Stainless Steel is a group of heat and corrosion resisting steels. They have in general a higher resistance to
corrosion in some definite environment, as well as a higher resistance to scaling at high temperature.
Stainless Steel are iron-based alloys containing a minimum of 10.5% Chromium with or without other alloying
elements. Based on the alloy content and the micro structure, stainless steels are classified into three major
categories viz. Austenitic, Ferritic and Martensitic.
Austenitic
This category of stainless steel contains 16 to 26% Chromium and 6 to 22% Nickel. they are nonmagnetic
annealed condition and have excellent corrosion resistance. They are not hardenable by heat treatment.
However, they can develop high strength on cold working. They have excellent weldability, formability, hygiene
factor and cryogenic properties. On cold working they exhibit different degrees of magnetism. They are
identified in the AISI 300 series.
Ferritic
This category of stainless steel contains 10.5 to 30% chromium without any Nickel. They are Ferro magnetic in
nature and generally not hardenable by heat treatment. These steels possess good resistance to stress corrosion
cracking and moderate weldability & formability. They are identified in the AISI 400 series.
Martensitic
This group contains 11 to 14% chromium without any nicket, but with a higher carbon content compared to the
Austenitic and ferritic stainless steels. They are ferro-magnetic in nature and are hardenable by heat treatment.
They possess moderate corrosion resistance
and are identified in the AISI 400 series.
Width (mm)
0.30, 0.35
0.40, 0.45
0.5
0.60
0.63
0.70
0.8, 0.9
1.00
900, 920, 1000, 1020, 1220, 1250, 1270, 1320, 1420, 1520, 1580
1.25, 1.50
900, 920, 1000, 1020, 1220, 1250, 1.60/1.85 1270, 1320, 1420, 1520, 1580, 1620
2.00
900, 920, 1020, 1220, 1250, 1270, 1320, 1420, 1520, 1580, 1620
Bitumen Size
0.63
Barrel Size
0.9
1, 1.2, 1.25
Note : 914 width in barrel thickness may be available as dimension out of barrel production
Coil Dimension : Outer diameter : 2200 mm, maximum. Internal diameter : 510 mm (thickness 0.63 mm and below and width
up to 1020 mm) and 600 mm (for other sizes) and Coil weight: 6-23 tonnes (as per size)
Tolerance as per IS - 513/1994
Common Grades : IS 513/1994 (O, D, DD & EDD), IRSM 41, SAILCOR, Copper Bearing, HSCR - 26/35. Bokaro Steel Plant
also produces cold rolled coils and sheets to the following foreign specifications : ASTM A 568/366, BS-1449-Pt-1, JIS G
3141 SPCC/CD, DIN-1623 St 12.3 or equivalent, if sufficient orders are available.
Rourkela Steel Plant : Rationalised Sizes of CR Coils
Thickness (mm)
Width (mm)
900
0.63, 0.8
900/1000/1020
900/1000/1020, 1250/1270
Coil weight : 3 to 15 tonnes for width above 1100 mm and 3 to 10 tonnes up to 1100 mm width.
Coil Internal Diameter : 610 mm (CR-1 route) and 510 mm (Tandem Mill route).
Common Grades : IS 513/1994 Grade
Note : Some quantity may be available in mixed thicknesses of 0.3 - 0.5 mm and mixed widths of 750-1000 mm
Width (mm)
Length (mm)
0.80, 0.90
1.0/1.25
915, 920
1815
1.0/1.25
1315, 1320
1970, 2000
Barrel Size
Common grades : IS 513/1994 (O, D, DDK, EDB), IRSM 41, SAILCOR, Copper Bearing CR coils/sheets are supplied in
oiled/unoiled condition as per customers requirements. Tolerance as per IS - 513/1994.
Rourkela Steel Plant
Rationalised sizes of Cold Rolled Sheets
Thickness (mm)
1.0, 1.25, 1.6
Width (mm)
1250/1270
Length (mm)
2500
Packaging : CR Coils
Coils are first packed with paper and high-density polythene and then secured with steel strapping. A coil is strapped with
three eye and two circumferential straps. For identification, one sticker and one metallic tag with a sticker are provided. These
are then loaded into wagons with the eye of the coil in horizontal position. Coils are then unitised by strapping.
Packaging : CR Sheets
These are packed in packets of 3 - 10 tonnes each and covered with high density polythene and paper. Thereafter, these are
bound with steel straps. They also have stickers inside the packets and metal tags attached to the strips.
Up to
1250 mm
Up to 0.25
0.03
Above 0.25 Up to
0.40
0.04
Above 0.40 Up to
0.60
0.05
0.06
Above 0.60 Up to
0.80
0.06
0.07
0.08
Above 0.80 Up to
1.00
0.08
0.09
0.10
Above 1.00 Up to
1.25
0.09
0.10
0.12
Above 1.25 Up to
1.60
0.11
0.12
0.14
Above 1.60 Up to
2.00
0.12
0.14
0.16
Tolerance (mm)
Up to 1250 mm
+ 7, - 0
Above 1250 mm
+ 10, - 0
Tolerance
Up to 2000 mm
+ 15 mm, - 0 mm
Above 2000 mm
+ 0.75% of length, - 0
Above 1600 mm
Specification
C%
max
Grade
Mn %
max
P%
max
S%
max
MAE %
max
Si % max
CE
IS 513/2008 CR1
0.15
0.60
0.055
0.055
SAILNOX CR2
0.12
0.50
0.040
0.040
SAILPRESS CR3
DD
0.10
0.45
0.035
0.035
SAILPRESS CR4
EDD
0.08
0.40
0.030
0.030
SAIL DRAW
EDD
(CBT)
0.04
0.15
0.015
0.015
SAILRIM
0.070.11
0.350.45
0.040
0.040
0.06 max
0.05
0.25-.50
0.025
0.02
0.5-0.7 (Al:
0.08-0.12)
0.12
1.4
0.25
0.025
0.100.45
0.250.140
0.75
CR 1 HS
HS
SAILCOR (IRSM-41)
0.15
0.5
0.03 0.28-0.72
Specification
Grade
Yield
Strength
MPa Min
Tensile
Strength
Rm MPa
Elongation
%A
minLo=80
mm
Elongation
% A max
Lo=50 mm
Hardness
HRB
Hardness
HR(30T)
rbar
min
nbar
min;
CR1 HSCR 26
0340
260 min
340 min
26
29
HSCR30
0390
300 min
390 min
23
26
HSCR 35
0440
350 min
440 min
20
23
CR2
240
370 max
30
31
65
60
CR3
DD
220
350 max
34
35
57
55
1.5
0.21
CR4
EDD
210
350 max
36
37
50
50
1.5
0.21
SAIL DRAW CR
(IF)
EDD
(CBT)
190
300 max
40
1.7
0.22
300 min
440 min
26
SAILCOR(IRSM41)
Application
Specification
Size
Application
Coated Sheets
SAILNOX
IS: 513 O (Sk)/D (K)
Packaging
SAIL PRESS
IS: 513 D/DD/EDD
All sizes
0.8 to 2 mm thickness
Precision tubes
SAILCOR (IRSM41)
1.25 to 2 mm thickness
Railway Couches/Wagons
0.63 to 2 mm thickness
SAILRIM, SAILHUB
SAILMUDGUARD
Cycle manufacturing
SEMI PROCESSED
ELECTRICAL STEEL, SAIL 0.5 to 0.63
LEC
HSCR 26/35
0.8 to 2.0
Sizes
(mm)
Dimension
Thickness
0.3 to 6.00
0.30, 0.40, 0.50, 0.55, 0.63, 0.70 0.80, 0.90, 1.00, 1.25, 1.50, 1.60, 2.00 2.50, 2.80,
3.00, 3.15, 3.60, 4.00, 5.00, 6.00
Width (mm)
50 to 1250
1000, 1250
Inner
Diameter
Dimension
Thickness
0.5 to 6.00
0.50, 0.55, 0.63, 0.70, 0.80, 0.90, 1.00, 1.25, 1.50 1.60, 2.00, 2.50, 2.80, 3.00, 3.15,
3.60, 4.00, 5.00, 6.00
Width (mm)
Length (mm)
Finish
Description
Remarks
No: 1
CR
Work hardened
2D
2B
No. 3
No. 4
No. 8
Special
Finishes
Dull Finish
Thickness
Range
Thickness range
Permitted on
Thickness
thick(Total)
Thickness
Tolerance
Permitted
Tol. () on
thick
<=1000
>1000 to
<=1275
0.30
0.040
2.00
0.18
< =0.30
0.030
>0.30 to 0.50
0.060
2.25
0.20
> 0.30 to
<=0.40
0.040
0.040
>0.50 to 0.80
0.080
2.50
0.23
> 0.40 to
<=0.50
0.045
0.050
>0.80 to 1.00
0.090
3.00
0.25
> 0.50 to
<=0.80
0.050
0.050
>1.00 to 1.50
0.100
3.50
0.30
> 0.80 to
<=1.00
0.055
0.060
>1.50 to 2.00
0.120
5.00
-0.25,+0.47
>1.00 to
<=1.50
0.080
0.080
>2.00 to 2.50
0.160
6.00
-0.25,+0.51
>1.50 to
<=2.00
0.10
0.10
>2.50 to 3.00
0.200
8.00
-0.25,+0.75
>2.00 to
<=2.5
0.10
0.11
>3.00 to 4.00
0.240
> 2.50 to
<=3.00
0.13
0.13
Close Tolerance
(Code C)
Any thickness closer
than precision
tolerance agreed by
mutual discussion
>3.00 to
<=4.00
0.17
0.17
> 4.00 to
<=5.00
0.17
0.17
> 5.00 to
<=6.00
0.17
0.20
>250 to <=600
>600 to <=1000
>1000 to <=1250
<1.00
+0.50, -0
+0.70, -0
+1.50, -0
+2.00, -0
+0.70, -0
+1.00, -0
+1.50, -0
+2.00, -0
+1.00, -0
+1.20, -0
+2.00, -0
+2.50, -0
+1.20, -0
+1.50, -0
+3.00, -0
+3.00, -0
+2.00, -0
+2.00, -0
+4.00, -0
+4.00, -0
Precision Tolerance on width (Trimmed Edge) CRSS coils (Code P). Any width stricter than normal tolerance agreed by
mutual discussion.
Normal Tolerance for sheets and
coils (Code N - No. 1 Trimmed
Edge)
Permitted
Tol. Width
Normal
Tolerance
(Code N) No.1 Specified
Length
Normal Tolerance
(Code N) - No.1
PermittedTol. on
Length
Normal
Tolerance
(Code N) CRSS
Specified
Length
Normal Tolerance
(Code N) - CRSS
PermittedTol. on
Length
Thick
Width
<=5.00
<=5.00
<1200
>=1200
Specified Length
Permitted Tol. on
length
> 5.00
to
<=6.00
<1200
+4, -0
<=2000
+5, -0
<3000
+12, -0
> 5.00
to
<=6.00
>=1200
+9, -0
>2000
+0.0025 x L, -0
3000
+0.005 x L, -0
< 5.0
< 900
13
< 5.0
900-1275
19
> =5.0
<=1275
23
Si
(max)
Mn
Cr
Ni
P
(max)
S
(max)
N
(max)
Other Elements
301
0.15
1.00
2.00
max
16.0018.00
6.008.00
0.045
0.030
0.1
301L
0.03
1.00
2.00
max
16.0018.00
6.008.00
0.045
0.030
0.2
304
0.07
0.70
2.00
max
17.519.5
8.0010.50
0.045
0.030
0.1
304L
0.03
0.75
2.00
max
17.519.5
8.0012.00
0.045
0.030
0.1
310S
0.08
1.50
2.00
max
24.0026.00
19.0022.00
0.045
0.030
316
0.08
0.75
2.00
max
16.0018.00
10.0014.00
0.045
0.030
0.1
Mo 2.0-3.0
316L
0.03
0.75
2.00
max
16.0018.00
10.0014.00
0.045
0.030
0.1
Mo 2.0-3.0
321
0.08
0.75
2.00
max
17.0019.00
9.0012.00
0.045
0.030
0.1
SSLNQ
0.12
0.75
10.5
max
14.515.5
0.301.00
0.075
0.015
0.20
Cu 2.0 max
SSLN1
0.12
0.75
10.0
max
14.0016.00
0.901.70
0.075
0.030
0.20
Cu 2.2 max
SSLN4
0.1
0.75
8.0
14.0017.00
3.804.70
0.070
0.030
0.15
Cu 2.2 max
204 Cu
0.15
1.00
6.509.-00
15.517.5
1.5-3.5
0.060
0.030
0.25
Cu 2.0-4.0
409
0.03
1.00
1.00
max
10.5011.70
0.50
max
0.04
0.02
0.03
SS
409M
0.03
1.00
0.5-1.5
10.8012.50
1.5 max
0.040
0.030
0.03
410S
0.08
1.00
1.00
max
11.5013.50
0.6 max
0.040
0.030
420
0.15
max
1.00
1.00
max
12.0014.00
0.75
max
0.040
0.030
Mo 0.5 max
430
0.12
1.00
1.00
max
16.0018.00
0.75
max
0.040
0.030
439
0.03
1.00
1.00
max
17.0019.00
0.5 max
0.040
0.030
0.03
U.T.S.
0.25 Proof
% El
Hardness
Cold Bend
301
515
205
40
95
Not required
301L
550
220
45
100
Not required
304
515
205
40
92
Not required
304L
485
170
40
92
Not required
310S
515
205
40
95
Not required
316
515
205
40
95
Not required
316L
485
170
40
95
Not required
321
515
205
40
95
Not required
204 Cu
650
310
40
Not required
SSLN4
600
275
40
96
Not required
409
380
170
20
88
180 1t
SS409M
450
275
22
92
180 1t
410S
415
205
22*
89
180 1t
420
690 max
15
96
Not required
430
450
205
22*
89
180 1t
439
415
205
22
89
180 1t
301
304/304L 316/316L
310S
430
409
Density (gm/cm2)
7.9
7.9
8.0
7.9
7.7
7.7
19700
19700
19700
20300
20300
20300
0.12
0.12
0.12
0.12
0.11
0.11
0.039
0.039
0.037
0.033
0.0625
0.0595
72
72
74
80
60
57
19.8
18.4
16.0
16.9
11.34
11.52
14001420
1400-1455 1370-1400
14001455
14301510
14301510
C) PLATES:
Plates (Bhilai Steel Plant)
Rationalised sizes of Plates from Plate Mill
Length(mm)
Thicknes(mm)
Width(mm)
Width
(mm)
1600
1800
2000
2200
2500
6300
9300
12500
10
6300
9300
12500
6300
9300
12500
12
2800
6300
7100
8000
10000
12500
9300
5600
6300
7100
9000
9300
12500
5000
5600
6300
7100
8000
9000
12500
16
7100
9300
9000
9300
12500
5600
7100
9000
9300
12500
5000
6300
8000
9000
12500
5600
7100
8000
10000
18
5600
7100
9300
5600
6300
7100
8000
9000
9300
12500
5000
6300
8000
9000
12500
5000
5600
6300
7100
9000
8000
9300
10000
10000
20
5600
7100
9300
5000
5600
6300
7100
9000
9300
12500
5000
5600
6300
8000
9000
12500
5000
5600
6300
7100
9000
8000
9300
10000
10000
22
5000
5600
6300
7100
9000
9300
5000
5600
6300
8000
9000
12500
5000
5600
6300
7100
7100
8000
9300
10000
10000
25
5000
5600
6300
8000
12500
5000
5000
6300
5600
9000
7100
9300
10000
10000
28
5000
5600
7100
10000
5000
6300
9000
9300
10000
32
5000
5600
9000
9300
10000
36
5000
14
3000 3200
5600
8000
9000
9300
5600
6300
8000
9000
9300
5000
5600
7100
8000
9300
5600
6300
8000
9000
9300
5000
5600
7100
8000
6300
5600
6300
7100
6300
12500
12500
12500
5600
8000
9000
9300
5000
5600
7100
8000
5600
6300
6300
7100
10000
12500
12500
5000
6500
8000
9000
5000
7100
8000
5000
5600
6300
6300
7100
12500
12500
5000
6300
5600
5000
5600
6300
10000
12500
5000
5600
9300
10000
5000
5600
9300
10000
5000
9000
9300
10000
5000
8000
9000
10000
5000
8000
7100
5600
8000
9000
7100
8000
9000
9300
8000
9000
40
5000
7100
8000
7100
5000
6300 5600 5000
8000
9000
7100
7100 6300 5600
9000
9300
8000
12500 12500 10000
93000
10000
10000
6300
7100
8000
45
6300
7100
12500
7100
8000
6300
7100
6300
7100
50
5600
6300
12500
5000
6500
9300
10000
7100
8000
6300
7100
5600
6300
7100
5600
6300
56
5000
5600
9300
10000
5000 8000
9300 9000
10000 9300
7100
8000
6300
7100
5600
6300
5000
5600
5000
5600
63
4500
5000
9000
9300
10000
8000
9300
7100
8000
6300
7100
5600
6300
5000
5600
4500
5000
4500
5000
75
7100
8000
6300
7100
5600
6300
5000
5600
4500
5000
4500
5000
4500
80
6300
7100
8000
5600
6300
7100
5000
5600
6300
4500
5000
5600
4500
5000
90
6300
5600
6300
5000
5600
5000
100
5000
5600
6300
5000
5600
5000
110
5000
5600
5000
120
4500
5000
5000
8000
9000
9000
9300
9300
10000
Note :
1) Plates above 40 mm will be flame cut.
2) Plates up to 13.5 metre length can also be rolled from slabs of new slab caster.
Thickness
(mm)
Width (mm)1600
1800
25
5000 5600
7100
10000
5000
6300
9000
9300
10000
5600
6300
8000
9000
9300
28
5000 6300
9000 9300
10000
5600
8000
9000
9300
32
36
2000
2200
2500
2800
3000
3200
5000
5600
7100
8000
6300
7100
12500
6300
12500
5600
6300
1250
5000
5600
7100
8000
6300
7100
12500
5600
6300
12500
5600
6300
10000
12500
5000
5600
9300
10000
5000 5600
8000 9000
5000
7100
8000
5000
6300
7100
12500
5600
6300
12500
5000
5600
9300
10000
5000
9000
9300
10000
5000
8000
9000
9300
10000
5000 7100
8000
6300
7100
12500
5600
6300
12500
5000
5600
9300
12500
5000
8000
9000
9300
8000
9000
9300
7100
8000
9000
5000
5600
10000
5000
9000
9300
10000
7100
8000
9000
9300
10000
7100
8000
6300
7100
8000
40
6300 7100
12500
5600
6300
12500
45
5600 6300
12500
5000
5600
10000
5000
9300
10000
8000
9000
9300
7100
8000
6300
7100
6300
7100
50
5000 5600
9300
10000
5000
9000
9300
10000
8000
9000
9300
7100
8000
6300
7100
5600
6300
7100
5600
6300
56
5000 9300
10000
8000
9000
9300
7100
8000
6300
7100
5600
6300
5000
5600
5000
5600
63
8000 9300
7100
8000
6300
7100
5600
6300
5000
5600
4500
5000
4500
5000
Length
(mm)
Thickness
(mm)
Width (mm)1500/1600
8,10,12
6300,
8000,9000,9300,10000
14,
16,18, 20
22, 25
4500, 5000,
5600,6300,7100,8000,
9000, 9300,10000, 12500
28
32
36
40
4500, 5000,
5600,6300,7100,
8000,9000
45
5600, 6300
50
5000, 5600
56
5600, 6300
63
5600
Note :
1. For 8 mm order acceptable in minimum width of 1600 mm.
2. For normalised plates minimum length to be 6300 mm.
3. Plates can be supplied with random ultrasonic testing (offline) up to maximum 50 mm thickness.
4. Plates in other sizes can be supplied as per mutual agreement.
Packing & Supply Condition
Plates are supplied in bare packaging condition. Plates are normalised
as per the requirements of specification. Thickness wise supply
conditions are mentioned here :
Rourkela Steel Plant
Rationalised sizes of Plates from Hot Strip Mill
Thickness (mm)
Supply Condition
8 -20 mm
Sheared condition
> 20-63 mm
Width (mm)
Length (mm)
1250
1250
5000, 10000
Note :
1. Plates are supplied in Mill Edge conditions ( Width + 20 to + 50 mm)
2. Chequered plates are supplied with tear drop pattern
Bokaro Steel Plant
Rationalised sizes of HR Plates
Thickness
(mm)
5, 6, 7, 8, 10
Width (mm)
1000, 1250,1400, 1500,
1600,1700, 1800
Length (mm)
4500, 5000,
5600,6300, 8000
Applications
Specification
Application
General structurals
SAIL Boiler
IS: 2002/1992 , ASTM-A-285 M (Grade C),
ASTM-A-515 M, ASTM-A-516 M,
ASTM-A-517 M (Grade F), ASTM-A-537 M (Class 1),
ASTM-A-204 (Grade B),
DIN 17155 (Grade H1), EN 10028, BS 1501
ASTM-A-517 (Grade F)
Penstock
SAILHARD
Abrasion Resistant
SAILMA 300, 350, 410, 450, 550, 550 HI, 600, 600 HI as per
IS: 2062/2006 DIN 17100 52.3, IS: 5986/2002, IS: 2062/2006,
E300, E350, E410, E450, D&E, 450E, Fe 510
High Tensile
SAIL Marine
IS: 3039, Lloyds Grade A, B, ABS Grade A, NCD 1431 LR Grade
E&D, ABS Grade AH/DH/EH-32, 36, NV Grade AB&D
Ship Building
Industrial Flooring
300HI/350HI/410HI/450HI
Wheels
Lloyds Grades A, B, D
IS: 2002/1992
ASTM-A-285 M
Grade C
Dead Soft Quality
LO-Pearl
IS: 8500/1992
IS: 5986/1992
IS: 3502
ASTM-A-517
Grade F
IS: 3039/1988
SAPH 440
ASTM-A-537 M Cl I
ASTM-A-515/ 516 M
Grades- 60/65/70
BSK-46
API 5L grade
A, B, X 42
X46, X52, X56
X60, X65
DIN St 42.2/52.3
SAIL SPP 400/700
Angles
Bokaro Steel Plant
IS: 2062/2006
SAILMA
300HI/350HI
E38/ E34
IS: 8500/1992
SAILCOR/ HCRS
IRSM-41
BSK-46
SAPH-45
IS: 1977Fe 290/330/370
IS: 2002
IRS Gr. A
E-550, E-500, E-450
ASTM AA 36
JIS 3101 SS 4011
IS: 5986
DIN 17100
IS: 6240
Rolling and cutting tolerance for plates (as per IS 1852/85) Width
The tolerances on width of plate shall be as follows
Lengthmm)
Width(mm)
Thicknessmm)
Tolerance on Width
Up to and
including 8000
Up to including 20
Over 20
- 0, +10 mm
-0 , +15 mm
Up to and
including 8000
Over 2000
Up to and including 20
Over 20
- 0, +0.5% of width
-0 +20 mm
Over 8000
All widths
Up to and including 20
Over 20
- 0, +0.2% of length
-0, +0.3% of length
Note 1 : Plates over 20 mm in thickness may be supplied with either as rolled or gas-cut edges. In case of Bhilai plates, above
40 mm thick plates shall be supplied with flame cut edges. The tolerances on width in such cases shall be subject to
arrangement between the purchaser and the supplier.
Note 2 : In case plates below 20 mm in thickness are supplied in as- rolled condition the tolerances shall be mutually agreed
to between the purchaser and the supplier.
Note 3 : Plates from BSP can be supplied in trimmed condition, width tolerance for untrimmed plates will be (+) 100 mm ()
mm
Thickness
The tolerances on thickness shall be as follows :
Thickness
Less than 8 mm
+12.5, - 5.0
+7.5, - 5.0
Over 12 mm
null
Length (mm)
Up to and
including
Length
(mm)Over
Thickness
(mm)
Tolerance
on length
2200
Up to and
including 20
Over 20
- 0, +10 mm
- 0, +15 mm
2200
3000
Up to and
including 20
Over 20
- 0, +0.5%
- 0, +15 mm
3000
6300
Up to and
including 20
Over 20
- 0, +0.5 %
- 0, +0.5 %
6300
8000
Up to and
including 20
Over 20
- 0, +35 mm
- 0, +0.5 %
8000
Up to and
including 20
Over 20
- 0, +35 mm
- 0, +40 m
The tolerance for length of plates from 5 to 10 mm thickness when produced in continuous mill shall be as follows
Length(mm)
Tolerance
GradeDesignation Quality
(1)
(2)
E 165
Ladle
Analysis
% Max
C
Ladle
Analysis
% Max
Mn
Ladle
Analysis
% Max
P
Ladle
Analysis
% Max
S1
Carbon
Equivalent
(CE) Max
(3)
(4)
(5)
(6)
(7)
(8)
(9)
0.25
1.25
0.045
0.045
0.40
0.42
Semi Killed
Ladle
Analysis
% Max S
Method of
Deoxidation
E 250
0.23
1.50
0.045
0.045
0.40
0.42
Semi
Killed/Killed
E 250
BR
BO
0.22
1.50
0.045
0.045
0.40
0.41
Killed
E 250
0.20
1.50
0.040
0.040
0.40
0.39
Killed
E 300
0.20
1.30
0.045
0.045
0.45
0.45
Semi
Killed/Killed
E300
BR
0.20
1.30
0.045
0.045
0.45
0.45
Killed
E 300
BO
0.20
1.30
0.045
0.045
0.45
0.45
Killed
E 300
0.20
1.30
0.045
0.045
0.45
0.45
Killed
E 350
0.20
1.50
0.045
0.045
0.45
0.42
Semi
Killed/Killed
E 350
BR
0.20
1.50
0.045
0.045
0.45
0.42
Killed
E 350
BO
0.20
1.50
0.045
0.045
0.45
0.42
Killed
E 350
0.20
1.50
0.045
0.045
0.45
0.42
Killed
E 410
0.20
1.60
0.045
0.045
0.45
0.46
Semi
Killed/Killed
E 410
BR
0.20
1.60
0.045
0.045
0.45
0.46
Killed
E 410
BO
0.20
1.60
0.045
0.045
0.45
0.46
Killed
E 410
0.20
1.60
0.045
0.045
0.45
0.46
Killed
E 450
0.22
1.60
0.045
0.045
0.45
0.48
Semi
Killed/Killed
E 450
BR
0.22
1.60
0.045
0.045
0.45
0.48
Killed
E 550
0.22
1.65
0.020
0.025
0.50
0.50
Killed
E 550
BR
0.22
1.65
0.020
0.025
0.50
0.50
Killed
E 600
0.22
1.70
0.020
0.025
0.50
0.50
Semi
Killed/Killed
E 600
BR
0.22
1.70
0.020
0.025
0.50
0.50
Semi
Killed/Killed
E 650
0.22
1.70
0.015
0.025
0.50
0.52
Killed
E 650
BR
0.22
1.70
0.015
0.025
0.50
0.52
Killed
Specification
SAIL MA
Specification
Grade
C%
max
Mn %
max
P%
max
S%
max
300
0.25
1.50
0.055
0.055
Nb+V+Ti%=0.20 (max)
300 HI
0.20
1.50
0.040
0.040
Nb+V+Ti%=0.20 (max)
350
0.25
1.50
0.040
0.040
Nb+V+Ti%=0.20 (max)
350 HI
0.20
1.50
0.040
0.040
Nb+V+Ti%=0.20 (max)
410
0.25
1.5
0.055
0.055
Nb+V+Ti%=0.20 (max)
410 HI
0.20
1.5
0.040
0.040
Nb+V+Ti%=0.20 (max)
450
0.25
1.5
0.055
0.055
Nb+V+Ti%=0.20 (max)
450 HI
0.20
1.5
0.040
0.040
Nb+V+Ti%=0.20 (max)
550
0.22
1.65
0.025
0.010
Nb+V+Ti%=0.30 (max)
550 HI
0.22
1.65
0.025
0.010
Nb+V+Ti%=0.30 (max)
660
0.22
1.75
0.025
0.010
660 HI
0.22
1.7
0.025
0.010
Grade
SAIL-FRS
C % max
Mn % max
P % max
S % max
Si %
0.20
1.5
0.040
0.040
1.0
Cr+Mo =1.000
Nb+V+Ti(max)
Note: Micro alloying elements like Nb, V, Ti or B shall be added singly or in combination and total micro alloying shall be as
indicated or as per mutual
agreement between SAIL & Purchaser.
Grad
e
C
max
Si
Mn
P
max
S
max
R
220
0.2
1
0.1
50.3
5
0.6
01.5
0
0.0
35
0.0
35
0.0
20
0.0
12
R
260
0.2
5
0.1
50.3
5
0.8
51.5
0
0.0
35
0.0
35
0.0
20
0.0
12
R
275
0.1
6
0.4
0
ma
x
0.8
01.5
0
0.0
25
0.0
15
0.0
20
0.0
12
0.0
5
R
355
0.1
8
0.5
0
ma
x
1.1
01.7
0
0.0
25
0.0
15
0.0
20
0.0
12
H
235
0.1
6
0.3
5
ma
x
0.6
01.2
0
0.0
25
0.0
15
0.0
20
0.2
0.4
0
ma
x
0.8
01.4
0
0.0
25
0.0
15
H
295
0.2
0.4
0
ma
x
0.9
01.5
0
0.0
25
H
355
0.2
2
0.6
0
ma
x
1.1
01.7
0
0.0
25
H
265
N
max
Nb
max
V
max
Ti
max
Nb+V+
Ti min
Cr
max
Cu
max
Mo
max
Ni
max
0.0
5
0.0
3
0.05
0.3
0
0.3
0
0.0
8
0.5
0
0.0
5
0.1
0
0.0
3
0.12
0.3
0
0.3
0
0.0
8
0.5
0
0.0
12
0.0
2
0.0
2
0.0
3
0.06
0.3
0
0.3
0
0.0
8
0.3
0
0.0
20
0.0
12
0.0
2
0.0
2
0.0
3
0.06
0.3
0
0.3
0
0.0
8
0.3
0
0.0
15
0.0
20
0.0
12
0.0
2
0.0
2
0.0
3
0.06
0.3
0
0.3
0
0.0
8
0.3
0
0.0
15
0.0
20
0.0
12
0.0
2
0.0
2
0.0
3
0.06
0.3
0
0.3
0
0.0
8
0.3
0
Tensi
le
Stren
gth
MPa
Elonga
tion
percen
t on
Gauge
Length
5.65/S
o min
Mechanical Properties
Grade
Yield
Stress
MPs
Min<=
16
R 220
220
Yield
Yield
Yield
Stress Stress Stres
MPs
MPs
s MPs
Min
Min>4 Min>
>16
0 to
60 to
to 40
60
100
mm
mm
mm
220
220
220
415540
21
Impact
Energy
(J) min
at a
temper
ature
in
Degree
C. of
20
50
Impact
Energy
(J) min
at a
tempera
ture in
Degree
C. of 0
40
Impact
Energy
(J) min
at a
tempera
ture in
Degree
C. of -20
27
20
R 260
260
260
260
260
490620
21
50
40
27
20
R 275
275
265
255
235
390510
23
80
70
50
40
R 355
355
345
335
315
490640
21
80
70
50
40
H 235
235
225
215
200
360480
24
40
34
27
H 265
265
255
245
215
410530
22
40
34
27
H 295
295
290
285
260
460580
21
40
34
27
H 355
355
345
335
315
510650
20
40
34
27
Grade
Designa
tion
(1)
Qualit
y
(2)
E-165
Tensile
Streng
th Rm
Mpa
(3)
Yield
Stress<
20
(4)
290
Yield
Stress2
0-40
(5)
Yield
Stress
>40
(6)
165
Charp
Interna Interna
y
Percent
Charp
l Bend
l Bend Impac
age
y
Impact Impact
t
Elongat
Impac
Test
Test
Test(
ion A at
t
Charpy( Charpy(
See
Gauge
Test(S
See
See
Note
Length
ee
Note 3
Note 3
2)Te
L=5.65
Note
&
& 4)
mp
VS Min
2)Min
4)<25
>25
Degre
e C.
(7)
(8)
(9)
(10)
(11)
23
2t
E-250
410
250
240
230
23
2t
3t
E-250
BR
410
250
240
230
23
2t
3t
RT
27
E-250
BO
410
250
240
230
23
2t
3t
27
E-250
410
250
240
230
23
2t
3t
(-)20
27
E-300
440
300
290
280
22
2t
E-300
BR
440
300
290
280
22
2t
RT
27
E-300
BO
440
300
290
280
22
2t
27
E-300
440
300
290
280
22
2t
(-)
20
27
E-350
490
350
330
320
22
2t
E-350
BR
490
350
330
320
22
2t
RT
27
E-350
BO
490
350
330
320
22
2t
27
E-350
490
350
330
320
22
2t
(-)
20
27
E-410
540
410
390
380
20
2t
E-410
BR
540
410
390
380
20
2t
RT
25
E-410
BO
540
410
390
380
20
2t
25
E-410
540
410
390
380
20
2t
(-)
20
25
E-450
570
450
430
420
22
2.5t
E-450
BR
570
450
430
420
22
2.5t
RT
20
E-450
BO
570
450
430
420
22
2.5t
20
E-450
570
450
430
420
22
2.5t
(-)
20
20
E-550
650
550
530
520
12
3.0t
E-550
BR
650
550
530
520
12
3.0t
RT
15
E-600
730
600
580
570
12
3.5t
E-600
BR
730
600
580
570
12
3.5t
RT
15
E-650
780
650
630
620
12
4.0t
E-650
BR
780
650
630
620
12
4.0t
RT
15
Interna
l
Diamet
er of
bend
Impact
Temp.
Energ
y
value
Yield
Strengt
h MPa
min 2040
Ultimate
Tensile
Strength
MPa min
>40
Elongat
ion %
min GL
5.65 So
Specificatio
n
Grade
SAIL MA
300
300
440-560
20
3T
300H
I
300
440-560
21
3T
350
350
490-610
20
3T
350H
I
350
490-610
21
3T
410
410
540-660
19
3T
410H
I
410
540-660
20
3T
450
450
570-720
18
3T
450H
I
450
570-720
19
3T
550
550
650
15
3.5T
550H
I
550
650
15
3.5T
20
15
600
600
730
15
3.5T
600H
I
600
730
15
3.5T
20
300
450
20
1.5T
SAIL FRS
Chemical Composition
Specification
Grade
C % max
Mn % max
P % max
S % max
Si % max
CE
ASTM A-36
0.25
Specification
Grade
0.80-1.20
C % max
0.04
0.05
0.15-0.40
Mn % max
P % max
S % max
CE
IS: 5986:2002
Fe 290
0.12
0.60
0.040
0.040
Fe 330
0.15
0.80
0.040
0.040
Fe 360
0.17
1.00
0.040
0.040
Fe 410
0.20
1.20
0.040
0.040
0.42
Fe 490
0.20
1.50
0.040
0.040
0.45
Fe 510
0.20
1.50
0.040
0.040
0.45
* under revision
Chemical Composition
Specification
ASTM- A-588
M
Grade
C % max
Mn %
max
0.19
0.801.25
P%
max
S%
max
Si %
max
0.040
0.050
0.300.65
CE
ST
52.3
HCRS
(Cu+P)
SAILCOR
(IRS M-41)
0.10
0.20-0.22
1.60
0.040
0.040
0.55
Al 0.02 min
0.15
0.250.8
0.070.15
0.03
0.280.50
Cu 0.2 min
0.25-0.45
0.0750.140
0.030.60
Al 0.03 max Cr 0.35-0.60 Ni
0.20-0.47 Cu 0.30-0.60 V
0.05 max
IS:
2002/1992
0.18
0.501.20
0.035
0.040
0.150.35
0.44
Cu 0.10% max
0.20
0.501.20
0.035
0.040
0.150.35
0.44
Al 0.022% max
0.22
0.501.20
0.035
0.040
0.150.35
0.44
ASTM-A-285
M
0.28
0.90
0.035
0.035
ASTM-A515M
60
0.24/0.27
0.90
0.035
0.035
0.150.40
Al 0.02% max
ASTM-A-516
65
0.28/0.31
0.90
0.035
0.035
0.150.40
70
0.31/0.33
1.20
0.035
0.035
0.150.40
55
0.18/0.22
0.600.90
0.035
0.035
65
0.24/0.28
0.851.20
0.035
0.035
70
0.27/0.30
0.851.20
0.035
0.035
- For each reduction of 0.10%
of C below the specified max
an increase of 0.60% of Mn
above the specified max is
permitted up to 1.50%. Grade 60 plates, Mn 0.851.20 for thickness <=12.5
mm - Heats will be micro
alloyed for orders requiring
impact test
ASTM-A537M
Cl 1
0.24
0.71.60
0.035
0.035
0.150.50
DIN 17155
H1
0.16
0.401.20
0.035
0.030
0.35
Al 0.02% min, Cr 0.25%
max, Ni 0.30% max, Cu
0.30% max, Nb 0.01% max,
V 0.03% max, Ti 0.03% max,
Mo 0.10% max
Chemical Composition
Specification
Grad
e
ASTM-A-36
Yield
Strengt
h MPa
Min
Ultimat
e
tensile
Strengt
h MPa
Min
250
400550
--
Elongatio
n % min
GL 5.65
So
---
----
Internal
diamete
r of
bend
-----
200 mm18 50
mm-21
<12
mm
>12
IS: 5986:2002
*
Fe
290
180
290400
30
Close
IS: 5986:2002
*
Fe
330
205
330440
28
Close
------
IS: 5986:2002
*
Fe
360
235
360470
28
2t
IS: 5986:2002
*
Fe
410
255
410520
24
2t
3t
IS: 5986:2002
*
Fe
490
335
490610
22
2t
2t
IS: 5986:2002
*
Fe
510
355
510620
20
2t
2t
ASTM-A-588 M
DIN 17100
345
485
ST
52.3
<16
mm
>16
<40
>40
>63
355
345
335
200mm
50m
m
16
19
490-630
18
<20
<25
>25
<40
1.5T
2t
Charp
y
Impac
t
energ
y 27J
at -20
SAILCOR
(IRSM41)HCRS(Cu+
P)
IS 2002/1992
340
480
22
<16
mm
>16
<40
>40
>60
UTS
235
225
215
360-480
24
2T
265
255
245
410-530
22
2T
290
285
280
460-580
21
3T
200
mm
50
mm
ASTM-A-285 M
205
385
515
23
27
ASTM-A-515 M
60
220
415
550
21
25
65
240
450
585
19
23
70
260
485
620
17
21
ASTM-A516 M
55
205
380
515
23
27
60
220
415
550
21
25
65
240
450
585
19
23
70
260
485
620
17
21
Charp
y
Impac
t
energ
y 18 J
for Gr
60 &
65 at
- 51
and
20J
ASTM-A-537 M
DIN 17155
Clas
sI
345
485620
HI
235 for
<16m
m
225 for
>16
<40
mm
18
for Gr
70 at 46
Degree
C. for 25
mm:
18J
for Gr
60 &
65 at
- 46
and
20J
for Gr
70 at
22
360
480
24
Charp
y
Impac
t
energ
y 31J
at 0
Degre
e C.
For ASTM-A-588 M/285 M/204 M/ 515 M/ 516 M/ 537 M & DIN 17100
Bend Test is a supplementary requirement
* under revision
Chemical Composition
Specification
ASTM-A-204
M
Grade
C % max
0.20/0.23
Mn %
max
0.90
P%
max
S%
max
Si %
max
0.035
0.035
0.150.40
CE
Mo 0.45 - 0.60%
ASTM-A 517
0.1-0.2
0.6-1.0
0.035
0.035
0.150.35
Ni 0.7-1.0 Cr 0.4-
- 40
for
>25
<50
0.65 Mo 0.4-0.6 V
0.03-0.08 Cu 0.150.50 Bo 0.00050.0006
API-5L
0.22
0.90
0.030
0.030
0.26
1.20
0.030
0.030
X-42
0.26
1.30
0.030
0.030
X-46
0.28
1.40
0.030
0.030
X-52
0.28
1.40
0.030
0.030
X-56
0.26
1.40
0.030
0.030
X-60
0.26
1.40
0.030
0.030
X-65
0.26
1.45
0.030
0.030
X-70
0.26
1.65
0.03
0.03
Nb+V+Ti<0.15%
IS:
3039/1988
0.23
0.040
0.040
**
0.42
***
* Mn content not
less than 2.5 times
Carbon content if
thickness >12.5
mm.
** Si 0.10-0.35% if
killed quality
otherwise up to
12.5 mm thickness.
*** Al min 0.01%
II
0.21
0.701.4
0.040
0.040
0.100.35
III
0.18
0.701.5
0.040
0.040
0.190.50
*
* Al min 0.015%
Lloyds
Grade
0.20-0.23
2.5xc%
min
0.035
0.035
0.50
0.40
0.21
0.80min
0.035
0.035
0.35
0.40
0.23
1.6
0.050
0.050
0.50
For Gr B
Mn
0.60%
min if
impact
tested.
SAILHARD
Al
0.10
max
GOST 19282
09G2S
0.12
1.3-1.7
0.035
0.040
0.50.8
10G2S1
0.12
1.31.65
0.035
0.040
0.81.1
Cr 0.65 max
Nb+V+Ti 0.15 max
Al 0.050 max Cr
0.30 max Ni 0.30
max Cu 0.30 max Ti
0.03 max N 0.008
max
Chemical Composition
Specification
Grade
C % max
Mn % max
P%
max
S%
max
Si %
max
others
Hardox
400
0.20
1.70
0.02
0.01
0.100.70
Cr : 0.80 max
Mo:0.80 max
Weldox
700E
0.21
1.4
0.02
0.01
0.40
Cr : 0.5
Mo : 0.45
V : 0.08
0.60
Al - 0.02 max
V - 0.20 max
Ti - 0.02 max
Nb - 0.050 max
0.22
1.60
0.025
0.015
Mechanical Properties
Specification
Grade
Yield Strength
MPa Min
Ultimate Tensile
Strength MPa Min
ASTM-A-204
M
Elongation % min
GL 5.65
Internal diameter
of bend
200mm
50mm
<25mm>
25
< 40 mm
1.5T 2T
275
485 -620
17 21
ASTM-A-517
690
795-930
16
API 5L
207
331
25
241-448
414-758
X-42
290-496
414-758
A :Cross sectional
area in mm2
X-46
317-524
434-758
U :Minimum UTS in
MPa
X-52
359-531
455-758
X-56
386-544
490-758
X-60
414-565
517-758
X-65
448-600
531-758
X-70
483-629
564-758
IS
3039/1988
Lloyds Grade
230
220
400-900
22
II
235
235
400-900
22
III
235
235
400-900
22
235
400-490
22
235
400-490
22
Specification
Grade
Yield
Strength
MPa Min
--
---
Ultimate
Tensile
Strength
MPa Min
----
Elongation
% min GL
5.65 S0
-----
SAILHARD
Hardness
- 200
BHN
(Min)
GOST
19282
8 to<10
10
to
<20
>20
<32
>32
<40
8
to<10
10
to
<20
>20 <32
>32
<40
09G2S
490
470
460
450
345
325
305
285
10G2S1
490
480
470
450
345
325
325
325
375
25
Internal
diameter
of bend
Elong 21,
Bend Test2T, Charpy
Impact
energy 59 J
min at
+20.Impact
for
category 3
only
DSQ LOPearl
245
304 for
t<6mm
SAIL SUPER
FORM
SAPH
45/440
294 for t
= 6-8
mm
3T
HCRS
Cu-P
340
480
21
SAIL SPP
400
900
1100
10
SAIL SPP
700
620
725860
16
SAIL HITEN
690 AR
550
690
15
3.5T
Note : The mechanical properties specified in API Grades are for pipes only. HRC/Plate properties are to be mutually agreed
upon by the producers & pipe manufacturers. The chemistry and mechanical properties of ABS grade Plates.
Grade
Chemistry
Tensile Strength
YS 235
UTS 400-520
Impact >50 mm 34J/RT
YS 235
UTS 400-520
Impact >25 mm 27J/0
YS 315
UTS 400-520
Impact 27J/2 for all thicknesses
AH 32 DH 32 EH 32
C 0.18, Mn 0.70-1.60
Nb 0.02-0.05,
S 0.035, P 0.035
V 0.05-0.10, Ti 0.02 max
YS 315
Imp AH 32 0C 34 J
DH 32 20C 34 J
EH 32 40C 34 J
AH 36 DH 36 EH 36
C 0.18
Mn 0.70-1.60
S 0.035, P 0.035, Nb 0.02-0.05
V 0.05-0.10, Ti 0.02 max
YS 355
UTS 490-620
Imp AH 36 0C 34 J
DH 36 20C 34 J
EH 36 40C 34 J
Mechanical Properties
Processing of plate orders for Home Sales through Vacuum Degassing (VD)/Isothermal/normal route as per
customer requirements.
Category
Requirement:Grade
Requirement:
Specifications/Sub
Grades
Process:
Vacuum
Degassing (
VD) (Ref.
A20/A20
(Ref.
A20/A20
M:07 CI
5.3.4 & S1)
Process:
Isothermal(Ref.
A20/A20 M:07
CI 5.3.4 & S1)
Process:
Normal
Mild
IS 2062 E 250 A, B, C,
A/SA 283 A/SA 36,
BS4360 Gr 43A, BS/DIN
EN 10025 S235,275 JIS G
3101 SS 400, DIN 17100
RSt 37.2, 44.2 Other
Equivalent grades
>=50 mm
40 to <50 mm
All grades with
UT
<40
mm All
grades
IS 2002/1,2,3,
IS2041/1,2 A/SA 515 &
516 Grades A/SA 285
>=50 mm
40 to <50 mm
<40
mm
All
thickness
All
thickness
>=50 mm
40 to <50
mm
<40 mm
<40
mm
All
thickness
High Tensile
>=50 mm
40 to <50 mm
<40
mm
Special
All thickness
UT
All grades
All specifications/Sub
grades
>=50 mm
IMPACT
All grades
All specifications/Sub
grades
null
SPL TDC
All grades
All specifications/sub
grades
null
Normalised
Plate
As per mandatory
requirement of the
specification or as per
agreed TDC
Normalising
Rolling
As per requirement of
the customer
40 to <50 mm
<40
mm
Chemical Composition
Specification
ASTM- A-588
M
Grade
C % max
0.19
Mn %
max
0.801.25
P%
max
S%
max
Si %
max
0.040
0.050
0.300.65
CE
ST
52.3
HCRS (Cu+P)
SAILCOR (IRS
M-41)
0.10
0.20-0.22
1.60
0.040
0.040
0.55
Al 0.02 min
0.15
0.250.8
0.070.15
0.03
0.280.50
Cu 0.2 min
0.25-0.45
0.0750.140
0.030.60
0.18
0.501.20
0.035
0.040
0.150.35
0.44
Cu 0.10% max
0.20
0.501.20
0.035
0.040
0.150.35
0.44
Al 0.022% max
0.22
0.501.20
0.035
0.040
0.150.35
0.44
ASTM-A-285
M
0.28
0.90
0.035
0.035
ASTM-A515M
60
0.24/0.27
0.90
0.035
0.035
0.150.40
65
0.28/0.31
0.90
0.035
0.035
0.150.40
70
0.31/0.33
1.20
0.035
0.035
0.150.40
55
0.18/0.22
0.600.90
0.035
0.035
65
0.24/0.28
0.851.20
0.035
0.035
70
0.27/0.30
0.851.20
0.035
0.035
ASTM-A-516
Al 0.02% max
Cl 1
0.24
0.71.60
0.035
0.035
0.150.50
H1
0.16
0.401.20
0.035
0.030
0.35
Chemical Composition
Specification
Grade
ASTM-A-36
Yield
Strength
MPa Min
Ultimate
tensile
Strength
MPa Min
250
400-550
--
Elongation
% min GL
5.65 So
---
----
Internal
diameter of
bend
--
200 mm-18
50 mm-21
<12 mm
>12
IS: 5986:2002 *
Fe
290
180
290-400
30
Close
IS: 5986:2002 *
Fe
330
205
330-440
28
Close
IS: 5986:2002 *
Fe
360
235
360-470
28
2t
IS: 5986:2002 *
Fe
410
255
410-520
24
2t
3t
IS: 5986:2002 *
Fe
490
335
490-610
22
2t
2t
IS: 5986:2002 *
Fe
510
355
510-620
20
2t
2t
ASTM-A-588 M
200mm
50mm
<20
<25
DIN 17100
345
485
ST
52.3
<16 mm
>16
<40
>40
>63
355
345
335
SAILCOR (IRSM41)HCRS(Cu+P)
IS 2002/1992
340
16
19
490-630
18
480
22
<16 mm
>16
<40
>40
>60
UTS
235
225
215
360-480
24
2T
265
255
245
410-530
22
2T
290
285
280
460-580
21
3T
200
mm
50 mm
ASTM-A-285 M
205
385515
23
27
ASTM-A-515 M
60
220
415550
21
25
65
240
450585
19
23
70
260
485620
17
21
55
205
380515
23
27
60
220
415550
21
25
65
240
450585
19
23
70
260
485620
17
21
ASTM-A516 M
Charpy
Impact
energy 18 J
for Gr 60 &
65 at - 51
and 20J
ASTM-A-537 M
1.5T
Class
I
345
485-620
18
22
for Gr 70
at - 46
Degree C.
for - 25
mm:
18J f
60 &
- 46
20J f
70 at
DIN 17155
HI
235 for
<16mm
225 for
>16
<40 mm
360480
24
Char
Impa
energ
at 0
Degr
For ASTM-A-588 M/285 M/204 M/ 515 M/ 516 M/ 537 M & DIN 17100
Bend Test is a supplementary requirement
* under revision
Chemical Composition
Specification
ASTM-A-204
M
Grade
C % max
0.20/0.23
Mn %
max
0.90
P%
max
0.035
S % max
0.035
Si %
max
CE
0.150.40
Mo 0.45 - 0.60%
ASTM-A 517
0.1-0.2
0.6-1.0
0.035
0.035
0.150.35
Ni 0.7-1.0 Cr 0.4-0
0.6 V 0.03-0.08 C
0.0005-0.0006
API-5L
0.22
0.90
0.030
0.030
0.26
1.20
0.030
0.030
X-42
0.26
1.30
0.030
0.030
X-46
0.28
1.40
0.030
0.030
X-52
0.28
1.40
0.030
0.030
X-56
0.26
1.40
0.030
0.030
X-60
0.26
1.40
0.030
0.030
X-65
0.26
1.45
0.030
0.030
X-70
0.26
1.65
0.03
0.03
Nb+V+Ti<0.15%
IS:
3039/1988
0.23
0.040
0.040
**
0.42
***
* Mn content not l
times Carbon cont
>12.5 mm.
** Si 0.10-0.35%
otherwise up to 12
thickness.
*** Al min 0.01%
II
0.21
0.70-1.4
0.040
0.040
0.100.35
III
0.18
0.70-1.5
0.040
0.040
0.190.50
*
* Al min 0.015%
Lloyds Grade
0.20-0.23
2.5xc%
min
0.035
0.035
0.50
0.40
0.21
0.80min
0.035
0.035
0.35
0.40
0.23
1.6
0.050
0.050
0.50
For Gr B Mn
0.60% min if
impact tested.
SAILHARD
Al 0.10
max
GOST 19282
09G2S
0.12
1.3-1.7
0.035
0.040
0.50.8
10G2S1
0.12
1.3-1.65
0.035
0.040
0.81.1
Al 0.050 max Cr 0
0.30 max Cu 0.30
max N 0.008 max
Chemical Composition
Specification
Grade
C % max
Mn % max
P%
max
S%
max
Si %
max
others
Hardox 400
0.20
1.70
0.02
0.01
0.100.70
Cr : 0.80 max
Mo:0.80 max
Weldox 700E
0.21
1.4
0.02
0.01
0.40
Cr : 0.5
Mo : 0.45
V : 0.08
0.22
1.60
0.025
0.015
0.60
Al - 0.02 max
V - 0.20 max
Ti - 0.02 max
Nb - 0.050 max
Mechanical Properties
Specification
Grade
ASTM-A-204
M
Inte
200mm
50mm
<25m
25
< 40
1.5T 2
275
485 -620
17 21
ASTM-A-517
690
795-930
16
API 5L
207
331
25
241-448
414-758
X-42
290-496
414-758
X-46
317-524
434-758
X-52
359-531
455-758
X-56
386-544
490-758
X-60
414-565
517-758
X-65
448-600
531-758
X-70
564-758
IS 3039/1988
Lloyds Grade
483-629
230
220
400-900
22
II
235
235
400-900
22
III
235
235
400-900
22
235
400-490
22
235
400-490
22
Specification
Grade
Yield
Strength
MPa Min
--
---
Ultimate
Tensile
Strength
MPa Min
----
Elongation
% min GL
5.65 S0
SAILHARD
GOST 19282
8 to<10
10
to
<20
>20
<32
>32
<40
8 to<10
10 to
<20
>20 <32
09G2S
490
470
460
450
345
325
305
10G2S1
490
480
470
450
345
325
325
375
25
340
480
21
900
1100
10
620
725860
16
SAIL HITEN
690 AR
550
690
15
245
304 for
t<6mm
SAIL SUPER
FORM
SAPH 45/440
HCRS
Cu-P
294 for t =
6-8 mm
Note : The mechanical properties specified in API Grades are for pipes only. HRC/Plate properties are to be mutually agreed
upon by the producers & pipe manufacturers. The chemistry and mechanical properties of ABS grade Plates.
Grade
Chemistry
Tensile Strength
YS 235
UTS 400-520
Impact >50 mm 34J/RT
YS 235
UTS 400-520
Impact >25 mm 27J/0
YS 315
UTS 400-520
Impact 27J/2 for all thicknesses
AH 32 DH 32 EH 32
C 0.18, Mn 0.70-1.60
Nb 0.02-0.05,
S 0.035, P 0.035
V 0.05-0.10, Ti 0.02 max
YS 315
Imp AH 32 0C 34 J
DH 32 20C 34 J
EH 32 40C 34 J
AH 36 DH 36 EH 36
C 0.18
Mn 0.70-1.60
S 0.035, P 0.035, Nb 0.02-0.05
V 0.05-0.10, Ti 0.02 max
YS 355
UTS 490-620
Imp AH 36 0C 34 J
DH 36 20C 34 J
EH 36 40C 34 J
Mechanical Properties
Processing of plate orders for Home Sales through Vacuum Degassing (VD)/Isothermal/normal route as per customer requirem
Category
Requirement:Grade
Requirement: Specifications/Sub
Grades
Process: Vacuum
Degassing ( VD)
(Ref. A20/A20
(Ref. A20/A20
M:07 CI 5.3.4 &
S1)
Proces
Isotherma
A20/A20 M
5.3.4 & S
Mild
>=50 mm
40 to <50 mm
grades with U
>=50 mm
40 to <50 mm
All thickness
BS 1501-1 BS EN 10028-2-P295GH
& 355GH BS EN 10028-3-P355
All thickness
>=50 mm
40 to <50 mm
<40 mm
All thickness
High Tensile
>=50 mm
40 to <50 mm
Special
All thickness
UT
All grades
>=50 mm
IMPACT
All grades
null
SPL TDC
All grades
null
Normalised
Plate
Normalising
Rolling
40 to <50 mm