Professional Documents
Culture Documents
GARIS
yang didefinisikan dari A sampai K (Tanpa ada I) Tipe tipe garisnya adalah tebal, tipis, Lurus, bergelombang, zigzag, bersambungan, putus putus, putus putus titik, putus putus dua titik Garis yang tebal dua kali ketebalannya dibandingkan dengan garis yang lebih tipis.
No
1. 2. 3. 4.* 5. 6.
0.70 1.00 0.50 0.70 0.35 0.50 0.25 0.35 0.18 0.25 0.10 0.15
Sectioning Lines
Extension Lines Hidden Lines Outlines or Visible Lines Datum Lines Cutting-Plane/Viewing-Plane Lines
dan pendek secara bergantian dan diberikan spasi, dengan tanda yang panjang pada masing masing ujungnya. Centerlines harus memotong tanpa kekosongan Proporsi dari centerlines:
Garis yang panjang 15mm 20mm Garis yang pendek 2mm Spasi diantaranya 1mm
panah pada masing masing ujungnya. Garis tersebut tidak boleh putus kecuali jika dibituhkan space untuk dimensi.
dari bagian part dan menunjukkan bagian awal dan akhir dari actual dimensions. Nilai yang ditampilkan adalah panjang atau sudut. Dua terminator untuk mengindikasikan bagian awal dan akhir dari dimension line.
Leaders (B4)
Leaders digunakan untuk mengindikasikan suatu
part atau porsi terhadap suatu angka, note, atau referensi dan harus menjadi suatu garis yang tidak putus putus dibatasi dengan suatu kepala anak panah, dot, atau garis bergelombang
Break Lines
Phantom Lines
Phantom lines haruslah mengindikasikan
pergantian posisi dari part part dari item yang digambarkan, mengulangi detail, shall be composed of alternating one long and two short dashes, evenly spaced, with a long dash at each end
Sectioning Lines
Sectioning lines shall be used to indicate the
exposed surfaces of an object in a sectional view. They are generally thin full lines, but may vary with the kind of material shown in section.
Extension Lines
Extension lines or projection lines are used to
indicate the extension of a surface or to point to a location outside the part outline. They start with a short, visible gap from the outline of the part and are usually perpendicular to their associated dimension lines.
Hidden Lines
Hidden lines shall consist of short dashes, evenly
spaced. These lines are used to show the hidden features of a part. They shall always begin with a dash in contact with the line from which they begin, except when such a dash would form a continuation of a full line. Dashes shall touch at corners, and arcs shall begin with dashes on the tangent points
Tidak boleh ada gap tempat dimana garis tersebut bertemu Tidak boleh saling mendahului Ketika menggabungkan garis lurus dengan sumbu, garis haruslah menyambung satu sama lainnya.
Cutting-Plane/Viewing-Plane Lines
The cutting-plane lines shall be used to indicate a
plane or planes in which a section is taken. The viewing-plane lines shall be used to indicate the plane or planes from which a surface or surfaces are viewed.
Arrowhead
PART 2
stroke. When several dimensions are to be projected from the same position, the 'origin' indication is used, consisting of a small circle
a full stop or point is no longer recommended as the decimal marker. The ISO recommended decimal marker is now the comma. Thus, taking pi as an example, it should now be written as 3,142 and not 3.142. Thus, one million should be represented as 1 000 000 and not 1,000,000.
reproduction methods.
To achieve these requirements, there are some
Sifat
Tinggi huruf besar Tinggi huruf kecil h c
Perban dingan
h 0.7 h 2. 5 0. 5 3. 5 1. 5 0. 2 5
Ukuran
3. 5 2. 5
0. 7 5 2. 1 0. 3 5
5 3. 5
1 7 3
7 5
1 0 7
2 1 4 6
14 20 10 14
Jarak antara huruf a Jarak min antar baris b Jarak min antar kata e Tebal huruf d
1. 4 10 4. 2 0. 7
2. 4 8 28 20 1. 8. 2 4 1. 4 2
0.1 h
0. 5