Professional Documents
Culture Documents
1. The power transmission products manufactured by Goodyear meet agreed specifications according to established tests performed under controlled laboratory conditions and specific test requirements. These tests are not intended to reflect the performance of the product under actual conditions. Performance of the product as a component in a finished product may not necessarily meet the test requirements. Due to the number and variety of applications for which any power transmission product may be purchased and because Goodyear has no control over (or knowledge of) the conditions under which the product may be used by others. GOODYEAR DOES NOT RECOMMEND SPECIFIC APPLICATIONS OR PRODUCT DESIGNS OR ASSUME RESPONSIBILTY FOR USE RESULTS OBTAINED OR SUITABILITY FOR SPECIFIC APPLICATIONS. No statement contained herein shall be construed as a license to operate, or as a recommendation or inducement to infringe existing patents or as an endorsement of products of specific manufactures or systems. 2. NO RELIANCE. CUSTOMER ACKNOWLEDGES THE USE OF ITS OWN KNOWLEDGE, SKILL, JUDGMENT, EXPERTISE AND EXPERIENCE IN (i) the selection of the product and/or (ii) in the selection, provision, or designation of any specification or set of specifications for a product agreed upon by Customer and Goodyear; and CUSTOMER ACKNOWLEDGES THAT CUSTOMER DOES NOT RELY AND IS NOT RELYING ON ANY ORAL OR WRITTEN STATEMENTS, REPRESENTATIONS, OR SAMPLES MADE OR PRESENTED BY GOODYEAR, ITS EMPLOYEES, AGENTS AND/OR REPRESENTATIVES TO CUSTOMER. CUSTOMER ACKNOWLEDGES THAT CUSTOMER DOES NOT RELY AND IS NOT RELYING ON ANY KNOWLEDGE, SKILL, JUDGMENT, EXPERTISE OR EXPERIENCE OF GOODYEAR, ITS EMPLOYEES, AGENTS AND/OR REPRESENTATIVES IN CUSTOMERS SELECTION OF THE PRODUCT OR IN CUSTOMERS SELECTION, PROVISION OR DESIGNATION OF ANY SPECIFICATION OR SET OF SPECIFICATIONS. Without limiting the foregoing, CUSTOMER ACKNOWLEDGES THAT GOODYEAR SHALL NOT BE LIABLE FOR, AND CUSTOMER ASSUMES ALL RISK OF, INACCURATE OR UNSUITABLE SPECIFICATIONS OR INFORMATION PROVIDED, SELECTED OR DESIGNATED BY CUSTOMER. 3. LIMITATION OF WARRANTY. POWER TRANSMISSION PRODUCTS NOT MANUFACTURED BY GOODYEAR ARE SOLD WITHOUT WARRANTY, AS IS, AND ARE SUBJECT TO THE LIMITATION OF LIABILITY SET FORTH IN SECTION 4. SUBJECT TO THE LIMITATIONS OF SECTION 4 AND UNLESS OTHERWISE EXPRESSLY PROVIDED HEREIN, power transmission product that has been manufactured by Goodyear, unless sold without warranty AS IS, is warranted to be free from defects in material and workmanship. Subject to the preceding sentence, and except as otherwise expressly provided herein, GOODYEAR MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY OTHER MATTER WITH RESPECT TO THE POWER TRANSMISSION PRODUCT OR ANY OTHER PRODUCT, WHETHER USED ALONE OR IN COMBINATION WITH ANY OTHER MATERIAL OR PRODUCT OR IN ANY PROCESS. GOODYEAR SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES, EVEN IF GOODYEAR HAS BEEN NOTIFIED OF THE POTENTIAL OF SUCH A LOSS OR CLAIM. OTHER THAN THOSE SPECIFICALLY SET FORTH HEREIN, THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE PRODUCTS ON THE FACE OF GOODYEARS ORDER CONFIRMATION, EITHER EXPRESS OR IMPLIED. 4. LIMITATION OF LIABILTY OF GOODYEAR AND EXCLUSIVE REMEDY. Any Goodyear-manufactured power transmission product claimed to be defective in material or workmanship shall, upon Goodyears approval, be returned to Goodyear as designated, at the Customers expense. GOODYEAR WILL, AS THE EXCLUSIVE REMEDY, MAKE AN ADJUSTMENT FOR POWER TRANSMISSION PRODUCT IT FINDS TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP EITHER BY REPAIRING IT OR REPLACING IT AT AN ADJUSTMENT PRICE, OR IN LIEU THEREOF, AT GOODYEARS OPTION, GOODYEAR MAY REFUND THE PURCHASE PRICE UPON RETURN OF THE PRODUCT. Whenever a warranty for a specific product provides that no adjustment shall be made after a specified period of time, Goodyear shall not be responsible under the terms of such warranty unless claim is made within such period of time. GOODYEARS TOTAL RESPONSIBILITY AND LIABILITY FOR ANY AND ALL CLAIMS, LOSSES AND DAMAGES OF ANY KIND WHATSOEVER ARISING OUT OF ANY CAUSE WHATSOEVER (WHETHER UNDER ANY WARRANTY OR BASED IN CONTRACT, NEGLIGENCE, OTHER TORT, STRICT LIABILITY, BREACH OF WARRANTY, OTHER THEORY OR OTHERWISE) SHALL NOT EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCTS IN RESPECT TO WHICH SUCH CAUSE ARISES, AND IN NO EVENT SHALL GOODYEAR BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, OR PUNITIVE DAMAGES RESULTING FROM ANY SUCH CAUSE. NO EMPLOYEE, AGENT AND/OR REPRESENTATIVE HAS AUTHORITY TO MAKE ANY REPRESENTATION, PROMISE OR AGREEMENT, EXCEPT AS STATED HEREIN. GOODYEAR SHALL NOT BE LIABLE FOR, AND CUSTOMER ASSUMES ALL LIABILITY FOR, ALL PERSONAL INJURY AND PROPERTY DAMAGE CONNECTED WITH THE HANDLING, TRANSPORTATION, OR FURTHER MANUFACTURE, FABRICATION, ASSEMBLY, OR PROCESSING OF THE PRODUCT. 5. Prices are subject to change without notice and all such items will be billed at prices in effect at the time of shipment. Customer will be notified of any price increase and may cancel any undelivered portion of the order by written notice to Goodyear provided such written notice is received by Goodyear not more than 10 days after your receipt of notification of the increase. Upon such cancellation Customer shall have no liability to Goodyear for the canceled portion of the order except as to product manufactured or in process, components procured by Goodyear from outside sources, and special tooling and equipment procured for performance of the order. 6. All prices are subject to increase from time to time to compensate for any tax, excise or levy imposed upon the products sold, or upon the manufacture, sale, transportation, or delivery of them or whenever any tax, excise, levy, law or governmental regulation has the effect, directly or indirectly, of increasing the cost of manufacture, sale or delivery. If any government action or law should have the effect of establishing a maximum price on product to be delivered, Goodyear may, at its option and without liability to Customer, terminate its obligation with respect to future shipments upon thirty (30) days written notice. 7. Goodyear shall not be liable or deemed in default for failure to deliver or delay in delivery due to any cause beyond its reasonable control. If unable to meet delivery schedules, Goodyear will endeavor to allocate material fairly among its Customers, but reserves to itself final determination of the deliveries to be made without liability. 8. Goodyear will indemnify its Customer against all claims and demands for infringement of any United States patent by the product furnished under any accepted order provided the Customer notifies Goodyear of any patent infringement and upon request tenders Goodyear the defense of the claim. CUSTOMERS WHO FURNISH SPECIFICATIONS TO GOODYEAR AGREE TO HOLD GOODYEAR HARMLESS AGAINST ANY CLAIMS WHICH ARISE OUT OF GOODYEARS COMPLIANCE WITH SUCH CUSTOMER SPECIFICATIONS.
EPD FORM 8-21-01
TABLE OF CONTENTS
Overview
Goodyear Power Transmission Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 Maximizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
V-Belt Products
Introduction to V-Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Open End V-Belting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A, B, C, D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Hy-T Wedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3VX, 3V, 5VX, 5V, 8V . . . . . . . . . . . . . . . . . . . . . . .51-52 Narrow (Ultra-V) Sheaves . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V, 5V, 8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Hy-T Plus (Classical) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A(4L), B(5L), C, D . . . . . . . . . . . . . . . . . . . . . . . . .54-55 Torque Flex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AX, BX, CX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56-57 A/B Classical (Conventional) Sheaves . . . . . . . . . . . . . . . . . . .A/B, A/B (Large Bore), C, D . . . . . . . . . . . . . . . . . . . . .58 Hex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AA, BB, CC, CCP . . . . . . . . . . . . . . . . . . . . . . . . . .59-60 Instapower (Flexten Classical) . . . . . . . . . . . . . . . . . . . . . . . . . .83, 84(AF), 85(BF), 87(CF), 89 . . . . . . . . . . . . . . . .61-62 FHP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2L, 3L, 4L, 5L . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63-64 QT/FHP Sheaves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Variable Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Neothane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3M, 5M, 7M, 11M . . . . . . . . . . . . . . . . . . . . . . . . .66-67
General Information
Belt Size Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Bushings & General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77-78 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79-86 Mandrel Quantity Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 Belt Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88-89 Goodyear Matchmaker System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Oil and Chemical Resistance of Power Transmission Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Static Conductive Power Transmission Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Marketing Accessories & Aides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93-94
OVERVIEW
OVERVIEW
Goodyear is committed to maintaining a position of industry leadership. We have an enviable history of product innovation and Power Transmission Industry firsts, including: Eagle Pd premium synchronous belts with a patented H.O.T. (Helical Offset Tooth) design for reduced noise, reduced vibration, and increased efficiency. Technology that produces perfectly matched belts from run to run which we call Matchmaker belts. The Maximizer Drive Selection Analysis software program for easy, accurate selection of the best drive for your application. Torque Team Plus belts with the strength and power transmission capacity to replace large chain drives. Poly-V belts with nylon fabric rib facing, fiberloaded rib compounds, and fully machined rib surfaces. Equally important, the research and development that produced these dramatic improvements is a continuing process. On the horizon we have a multitude of new innovations that are being developed at our Research and Development Center in Lincoln, Nebraska.
CUSTOMIZED TRAINING
Whenever you need it, wherever you want it, customized training is available for your associates. From maintenance and installation clinics to in-depth training on analyzing failed power transmission products, our distributors and GTMs can give you the guidance needed to choose, install and maintain Goodyear power transmission products.
That means Goodyear Power Transmission Products will continue to meet the increasing demands for improved drive efficiency, long belt life, and competitive costs.
CUSTOMER SATISFACTION
Customer satisfaction is foremost in our guiding principles. It shows in our services. It shows in our products. Most importantly, it shows in the unparalleled customer quality rating Goodyear Power Transmission Products has received from several key OEMs. Weve determined that the surest route to customer satisfaction is through a constant effort to improve. This commitment guarantees the quality of Goodyears Power Transmission products, services, deliveries and moreboth now and in the years to come. With Goodyear, youre much more than a customer. You are an intergral piece to success. We pledge to support you with quality products, inventory, service, technical help and more. Goodyear has a tradition of product excellence and service. Along with our extensive distributor network, we form a team second to none in total product and service offerings. Our mutual goal is to supply you with the best products for your investment. We are constantly looking for ways to help you save on your existing processes, combining your expertise with our knowledge of power transmission products to make every operation as efficient as possible. Upgrade For Savings is a program we promote to maximize efficiencies, reduce maintenance costs and increase your productivity. We know that it only takes minor improvements in drive efficiency to save significant and measurable energy dollars. To pinpoint the improvements, we have developed easy-to-use software programssuch as Maximizer. With Maximizer, true drive costs can be analyzed; thus identifying the best drive combination for your needs. In many instances, Upgrade For Savings involves upgrading your drives to the latest innovative belt technology that allows for increased efficiency and reduced operating costs. For example, upgrading from a standard classical V-belt to a narrow V-belt can reduce hardware and maintenance costs while increasing horsepower and load carrying capabilities. To take it a step further, V-belts could be replaced altogether with a premium synchronous belt like Eagle Pd , permitting less maintenance and more efficiency.
QUALITY SERVICE
Our pledge is a simple one: Quality service that you can always depend on. It is a commitment from us and our distributors to you.
OVERVIEW
OVERVIEW Maximizer is an exciting new program which allows the user to have Goodyear belt specifications and information right at their fingertips. It is easy to install and easy to use, making drive recommendations a snap. With Maximizer, drive requirements specified by the user are matched with available belts, sprockets, pulleys, and bushings. The Maximizer screen allows the user to select the most efficient drive. With other pertinent information, such as customer prices, belt testing information and engineering drawings included, the benefits of Maximizer are quickly realized.
SYNCHRONOUS BELTS
name indicates, Positive Drive belts make possible power transmission that is efficient and accurate to a precise degree. Synchronous or Positive Drive Belts are a relatively new concept in power transmission belting evolution. These belts combine the advantages of chain and gear with the advantages of V-belts, but without the limitations usually associated with these conventional types of drives. There is no stretch, no metal-to-metal contact, and no constant lubrication. Synchronous belts are amazingly versatile with possible applications on drives up to 600 hp and from speeds under 100 feet per minute to over 6,000 feet per minute. Positive Drive, or Pd, is the term applied by Goodyear to synchronous belts and their method of power transmission. As the Positive Drive Belts also make possible important savings in weight, space and construction without the sacrifice of efficiency. They are adaptable to almost any type of power transmission drive from electric typewriters to heavy industrial milling machines and grinders. Engineered and manufactured with extreme care with pitch, tooth depth, width and other measurements accurate to a precise degree, Positive Drive Belts are highly engineered products. The materials used in these remarkable belts consist of high strength tension members, specially compounded rubber and proven synthetic fabrics. The belts are designed to eliminate excessive heat build-up and operate efficiently.
BELT LINE
drive design. And best of all, no flanges are required, translating into additional weight savings for your system. Eagle Pd Belts and Sprockets come in a wide variety of stock sizes with custom manufactured sizes being available for specialty drive requirements. WhiteHawk Pd, with its strength and unique construction of Hibrex and Plioguard facing, is a line of curvilinear, synchronous belts that offers universal performance that stands alone. Designed to fit virtually every high capacity synchronous application, WhiteHawk Pd belts fulfill existing drive requirements, matching industrial standards of belt width and length. With the Universal Profile Design (UPD) profile, WhiteHawk Pd performs in the GT and HTD profiles, replacing Gates PowerGrip GT and PowerGrip GT2 belts. In addition, WhiteHawk Pd replaces Dayco RPP and RPP Plus belts, running in RPP sprockets. The UPD is a simple solution in satisfying the multitude of belt and sprocket combinations in the market. For ease of ordering, the WhiteHawk Pd part number closely matches that of other belt part numbers, making it easy to replace its counterparts. Take universal performance to a higher level with WhiteHawk Pd. BlackHawk Pd is a high-performance, curvilinear belt that offers maximum performance in your 8mm and 14mm synchronous applications. Featuring both Hibrex and Flexten tensile member, BlackHawk Pd is precisely designed and manufactured to replace existing Dayco Panther, Browning Panther and TB Woods QT PowerChain belts, matching competitive offerings of belt width and length. Dynamic testing of BlackHawk Pd has shown this durable belt actually lasts 3 to 4 times longer than Dayco RPP Panther. Maximize the performance of your timing belt application with BlackHawk Pd, designed to deliver longer life and less maintenance. Choose the belt that takes performance to greater heightsBlackHawk Pd.
SuperTorque Pd represents the next evolution in synchronous drive belt development from Goodyear. The SuperTorque Pd belt has a unique modified round tooth design that minimizes tooth shear and operates quieter than traditional trapezoidal tooth profiles. Super-Torque tooth pitches include S3M, S4.5M, S5M, S8M, and S14M and are available as special manufacture parts with minimal runs. Hi-Performance Pd Plus, Goodyears universal round tooth belt, is interchangeable with other round tooth sprockets making for easy replacement of competitive belts. The difference between HPPD Plus and other round tooth products is the patented parabolic tooth profile which lends itself to reduced tooth stress, noise, and backlash. The HiPerformance Pd Plus product line includes a wide stock selection of 3M, 5M, 8M, 14M and 20M pitches. Eagle Pd Belts and Sprockets are Goodyears latest technological breakthrough. A patented H.O.T. (Helical Offset Tooth) design provides for continuous rolling tooth engagement, allowing the Eagle Pd System to run quieter with less vibration than any other synchronous belt available today. With specialized materials the Eagle Pd belt allows for a reduction in drive width allowing for a more compact, lighter
SYNCHRONOUS
EAGLE PD BELT
APPLICATIONS Goodyear Eagle Pd belts and sprockets are ideal on a wide variety of applications in all industries.
SYNCHRONOUS
Part No: B-1750 B Blue = 14 mm Pitch, 35 mm Width 1750 1750 mm Pitch Length
Agricultural Equipment Packaging Conveyors Aggregate Crushers Poultry/Meat Grinders Wood Debarkers & Saws Mining Equipment Aluminum/Steel Conveyors
Paper Presses Hog Dehairers Chain Drives Baking Mixers Textile Machines Horizontal Drives Printing Machines
KEY FEATURES & BENEFITS Reduced Noise Less Vibration Increased Horsepower Less Maintenance Higher Efficiency Compactness Less Bearing Load Self-Tracking Greater Precision Bidirectional
INCREASED EFFICIENCY
The unique tooth configuration of Eagle Pd provides continuous tooth engagement and eliminates slippage. With a power efficiency rating of 98%, Eagle Pd can offer you an impressive 5% edge over typical V-belt drives. Simply stated, with Eagle Pd, you get what you pay for with each energy dollar. This is especially true when the Eagle Pd is applied to high-energy consuming drives that are used 24 hours a day, as well as high horsepower drives that inflate energy consumption during peak periods.
EAGLE PD BELT
MATCHING BELT TO SPROCKET HAS NEVER BEEN EASIER
The Eagle Pd Spectrum color system makes it the easiest power transmission drive to sell, purchase and install. The part numbering system for Eagle Pd centers around a color-coded sizing system for the belts and sprockets. Each belt and sprocket part number includes a letter corresponding to a color and is also branded in that color. The letters Y, W, P, B, G, O, and R indicate the colors Yellow, White, Purple, Blue, Green, Orange, and Red. All Yellow belts are designed to function with all Yellow sprockets, as is the case for the White, Purple, Blue, Green, Orange and Red sizes. An example of the part numbering system nomenclature for belts, sprockets, and bushings follows and also appears on subsequent pages.
16mm
EAGLE Pd YELLOW
(8 mm Pitch - 16 mm Width) Part Number Y-1280 Y-1440 Y-1600 Y-1792 Y-2000 Y-2240 Y-2400
16mm
No. of Teeth 160 180 35mm 200 224 250 280 300
70mm
8mm Pitch 5.3mm
Length (in) 32mm 50.39 56.69 62.99 14mm 70.55 8.6mm Pitch 78.74 88.19 52.5mm 94.49
8mm Pitch
32mm
14mm Pitch
8mm Pitch
EAGLE Pd WHITE
(8 mm Pitch - 32 mm Width) Part Number Length (in) 35mm W-1280 25.20 W-1440 28.35 W-1600 31.50 W-1792 35.28 W-2000 39.37 70mm W-2240 44.09 W-2400 47.24
16mm 8mm Pitch 5.3mm
8 P
No. of Teeth
14mm 160 8.6mm Pitch 180
14mm Pitch
Length (in) 50.39 56.69 62.99 70.55 14mm 78.74 8.6mm Pitch 88.19 94.49
14mm Pitch
32mm
EAGLE Pd PURPLE
Part Number P-720 P-800 P-896 P-1000 P-1120 No. of Teeth 90 100 112 125 140
8mm
5.3mm
64mm
8.6mm 5.3mm
Length (in) 35mm 28.35 14mm Pitch 31.50 35.28 39.37 44.09 70mm
14mm Pitch
Part Number No. of Teeth P-1200 150 8.6mm P-1280 160 P-1360* 170 52.5mm P-144014mm 180 8.6mm P-1600 Pitch 200
8.6mm 105mm
The belt length in mm is given in the part number. *Size under consideration for a future line addition.
16mm
EAGLE PD BELT
35mm
8mm Pitch
5.3mm
32mm
8mm Pitch
EAGLE Pd BLUE
(14 mm Pitch - 35 mm Width) Length (in) 39.13 44.09 46.85 49.61 55.12 61.73 68.90 Part Number B-1960 B-2100 16mm B-2240 B-2380 B-2520 B-2660 B-2800
35mm
14mm Pitch
8.6mm
SYNCHRONOUS
No. of Teeth 140 150 70mm 160 5.3mm 8mm Pitch 170 180 32mm 190 200
14mm Pitch 8.6mm 52.5mm
Length (in) 52.5mm 77.17 82.68 88.19 93.70 14mm 8.6mm 99.21 Pitch 104.72105mm 8mm 5.3mm Pitch 110.24
Purple
14mm Pitch
64mm
8m Pit
14mm Pitch
EAGLE Pd GREEN
No. of Teeth 14mm 8.6mm 140 Pitch 150 105mm 160 170 180 35mm 190 200
16mm
14mm Pitch
8.6mm
8mm 5.3mm Length (in) Pitch 77.17 82.68 32mm 88.19 93.70 14mm 99.21 8.6mm Pitch 14mm 104.72 8.6mm Pitch 110.24 52.5mm
8mm Pitch
14mm Pitch
Purple
EAGLE Pd ORANGE
Part Number O-1120 O-1190 O-1260 O-1400 O-1568 O-1750 No. of Teeth 80 85 90 100 112 125
(14 mm Pitch - 70 mm Width) Part Number O-1960 35mm O-2100 O-2240 O-2380 O-2520 O-2660 70mm O-2800
No. of Teeth 140 150 14mm 8.6mm 160 Pitch 170 180 52.5mm 190 200
14mm Pitch
32mm
14mm Pitch
8.6mm 105mm
64mm
8mm Length (in) 5.3mm Pitch 77.17 14mm 82.68 Pitch 88.19 93.70 99.21 14mm 104.72 8.6mm Pitch 110.24
8m Pi
8.6mm 105mm
EAGLE Pd RED
Part Number R-1260 R-1400 R-1568 R-1750 R-1960 R-2100 No. of Teeth 90 100 112 125 140 150
(14 mm Pitch - 105 mm Width) Length (in) 49.61 55.12 61.73 68.90 77.17 82.68 Part Number R-2240 R-2380 R-2520 R-2660 R-2800 No. of Teeth 160 170 180 190 200
14mm Pitch
8.6mm
EAGLE PD SPROCKET
SYNCHRONOUS APPLICATIONS Goodyear Eagle Pd belts and sprockets are ideal for use on a wide variety of applications in all industries. KEY FEATURES & BENEFITS More design flexibility with more compact drives. No flanges. Self-tracking design. Available in ductile iron, aluminum, steel, or stainless steel.
Part No: Y-28S-H Y Yellow = 8 mm Pitch, 16 mm Width 28 28 Teeth S Sprocket H Hub/Bushing Type
This is a Green size sprocket with 34 teeth and a Finished Stock Bore (FSB) style hub featuring a bore of 1 7/8". FSB sprockets are supplied ready to install with a standard keyway and setscrew holes machined. Bored To Suit, BTS: B-28S-BTS-1 13/16
This is a Blue size sprocket with 28 teeth and a hub that has been bored (BTS) to 1 13/16", per customer specification, and machined for setscrew holes and a keyway. BTS sprockets can be made to almost any bore including metric sizes.
Note: All MPB-, QD-, and FSB-style sprockets are stock items. BTS sprockets are made to order and may require longer lead times.
Bushings are supplied with bolts, lock washers, and set screws. Keys are supplied only if a special shallow key is required. The E 2 1/8" bushing can be used to install any sprocket with an E hub on a 2 1/8" shaft. The QD bushing system is an industry standard, however, to ensure the best match between sprocket and bushing, we recommend using bushings supplied by Goodyear for Eagle Pd sprockets.
8mm
YELLOW
8mm
WHITE
10
SYNCHRONOUS
72mm 8mm
72mm
8mm
EAGLE Pd YELLOW
Part Number Y-18S-MPB Y-18S-7/8 Y-20S-MPB Y-20S-7/8 Y-20S-1 1/8 Y-22S-MPB Y-22S-7/8 Y-22S-1 1/8 Y-24S-MPB Y-24S-7/8 Y-24S-1 1/8 Y-24S-1 3/8 Y-25S-MPB Y-25S-7/8 No. of Teeth 18 18 20 20 20 22 22 22 24 24 24 24 25 25 Part Number Y-25S-1 1/8 Y-25S-1 3/8 Y-26S-MPB Y-26S-7/8 Y-26S-1 1/8 Y-26S-1 3/8 Y-26S-1 5/8 Y-28S-MPB Y-28S-H Y-30S-MPB Y-30S-H Y-32S-MPB Y-32S-H Y-34S-MPB
(8 mm Pitch - 17 mm Width)
No. of Part No. of mm Part Teeth Number Teeth Number Y-34S-H 34 14 Y-52S-MPB 25 Y-56S-MPB 3654.5mm 25 37mm Y-36S-MPB mm Y-56S-SDS Y-36S-SH 36 26 Y-60S-MPB Y-38S-MPB 38 26 54.5mm 37mm Y-60S-SDS Y-38S-SH 38 26 Y-63S-MPB Y-40S-MPB 40 26 Y-63S-SDS Y-40S-SH 40 26 Y-64S-MPB Y-44S-MPB 44 28 14 Y-68S-MPB Y-45S-MPB 45 28 mm Y-72S-MPB Y-45S-SDS 45 30 14mm Y-75S-MPB Y-48S-MPB 48 30 14 Y-75S-SDS Y-48S-SDS 48 32 mm 14mm 107mm50 Y-76S-MPB Y-50S-MPB 32 Y-80S-MPB Y-50S-SDS 50 34
14
107mm
No. of Teeth 52 56 56 60 60 63 63 64 68 72 75 75 73 80
Part Number Y-80S-SDS 65mm Y-90S-MPB Y-90S-SK Y-112S-MPB 65mm Y-112S-SK Y-140S-MPB Y-140S-SK Y-180S-MPB Y-180S-SF Y-224S-MPB Y-224S-E
No. of Teeth 80 90 90 112 112 140 140 180 180 224 8mm 224
8mm
EAGLE Pd WHITE
Part Number W-18S-MPB W-18S-7/8 W-20S-MPB W-20S-7/8 W-20S-1 1/8 W-22S-MPB W-22S-7/8 W-22S-1 1/8 W-24S-MPB W-24S-7/8 W-24S-1 1/8 W-24S-1 3/8 W-25S-MPB W-25S-7/8 No. of Teeth 18 18 20 20 20 22 22 22 24 24 24 24 25 25 Part Number W-25S-1 1/8 W-25S-1 3/8 W-26S-MPB W-26S-7/8 W-26S-1 1/8 W-26S-1 3/8 W-26S-1 5/8 W-28S-MPB W-28S-H W-30S-MPB W-30S-H W-32S-MPB W-32S-H W-34S-MPB
(8 mm Pitch - 33 mm Width)
Part Number W-34S-H W-36S-MPB W-36S-SH W-38S-MPB W-38S-SH W-40S-MPB W-40S-SH W-44S-MPB W-45S-MPB W-45S-SDS W-48S-MPB W-48S-SDS W-50S-MPB W-50S-SDS No. of Teeth 34 36 36 38 38 40 40 44 45 45 48 48 50 50
No. of Teeth 25 25 26 26 26 26 26 28 28 30 30 32 32 34
No. of Teeth 52 56 56 60 60 63 63 64 68 72 75 75 76 80
Part No. of Number Teeth W-80S-SDS 80 W-90S-MPB 90 W-90S-SK 90 W-112S-MPB 112 W-112S-SK 112 W-140S-MPB 140 W-140S-SK 140 W-180S-MPB 180 W-180S-SF 180 W-224S-MPB 224 W-224S-E 224
72mm
14 mm 54.5mm
EAGLE PD SPROCKET 14 mm
65mm
37mm
54.5mm
SYNCHRONOUS
14mm 107mm
14 mm
PURPLE
8mm
BLUE
14mm 107mm
No. of Teeth 56 60 63 64
14 mm
EAGLE Pd PURPLE
Part Number P-24S-MPB P-25S-MPB P-26S-MPB P-28S-MPB P-30S-MPB No. of Teeth 14 24 mm 25 26 28 30 Part Number P-32S-MPB P-34S-MPB P-36S-MPB P-38S-MPB P-40S-MPB
(8 mm Pitch - 65 mm Width)
Part Number P-44S-MPB P-45S-MPB P-48S-MPB P-50S-MPB P-52S-MPB No. of Teeth 44 45 48 50 52 Part Number P-56S-MPB P-60S-MPB P-63S-MPB P-64S-MPB Part No. of Number Teeth P-68S-MPB 68 P-72S-MPB 14 72
No. of Teeth 32 34 36 38 40
mm
EAGLE Pd BLUE
Part Number B-28S-MPB B-28S-SK B-30S-MPB B-30S-SK B-32S-MPB B-32S-SK B-34S-MPB B-34S-SK B-36S-MPB No. of Teeth 28 28 30 30 32 32 34 34 36 Part Number B-36S-SF B-38S-MPB B-38S-SF B-40S-MPB B-40S-SF B-43S-MPB B-43S-SF B-45S-MPB B-45S-SF
Sprockets with MPB (Minimum Plain Bore) are specified when the sprocket does not allow room for a bushing that will handle the maximum load.
11
17mm
33mm 14 mm
14 mm 54.5mm
EAGLE PD SPROCKET
8mm 8mm 14mm 65mm 72mm 107mm
7mm
12
SYNCHRONOUS
14mm 107mm
Part Number G-28S-MPB G-28S-1 7/8 G-28S-2 1/8 G-28S-2 3/8 G-30S-MPB G-30S-1 7/8 G-30S-2 1/8 G-30S-2 3/8 G-32S-MPB G-32S-1 7/8
14 mm
GREEN
14 mm 8mm 37mm
ORANGE
14 mm 65mm
No. of Teeth 56 56 60 60 63 63 71 71 75 75 Part No. of Number Teeth G-80S-MPB 80 G-80S-J 80 8mm G-90S-MPB 90 G-90S-J 90 G-112S-MPB 112 G-112S-J 112 G-140S-MPB 140 G-140S-M 140 G-168S-MPB 168 G-168S-M 168
54.5mm
No. of Part Teeth Number 40 14 G-56S-MPB 40 mmG-56S-E G-60S-MPB 43 G-60S-E 43 G-63S-MPB 45 G-63S-E 45 G-71S-MPB 48 G-71S-J 48 G-75S-MPB 50 G-75S-J 50
RED
EAGLE Pd GREEN
No. of Teeth 28 28 28 28 30 30 30 30 32 32 Part Number G-32S-2 1/8 14 G-32S-2 3/8 mm G-34S-MPB G-34S-1 7/8 G-34S-2 1/8 G-34S-2 3/8 G-36S-MPB G-36S-SF G-38S-MPB G-38S-SF
14 mm
EAGLE Pd ORANGE
Part Number O-28S-MPB O-28S-1 7/8 O-28S-2 1/8 O-28S-2 3/8 O-30S-MPB O-30S-1 7/8 O-30S-2 1/8 O-30S-2 3/8 O-32S-MPB O-32S-1 7/8 O-32S-2 1/8 O-32S-2 3/8 O-32S-2 7/8 No. of Teeth 28 28 28 28 30 30 30 30 32 32 32 32 32 Part Number O-34S-MPB O-34S-1 7/8 O-34S-2 1/8 O-34S-2 3/8 O-34S-2 7/8 O-36S-MPB O-36S-1 7/8 O-36S-2 1/8 O-36S-2 3/8 O-36S-2 7/8 O-38S-MPB O-38S-1 7/8 O-38S-2 1/8
No. of Teeth 34 34 34 34 34 36 36 36 36 36 38 38 38
EAGLE Pd RED
Part Number R-28S-MPB R-28S-1 7/8 R-28S-2 1/8 R-28S-2 3/8 R-28S-2 7/8 R-30S-MPB R-30S-1 7/8 R-30S-2 1/8 R-30S-2 3/8 R-30S-2 7/8 R-32S-MPB R-32S-1 7/8 R-32S-2 1/8 R-32S-2 3/8 No. of Teeth 28 28 28 28 28 30 30 30 30 30 32 32 32 32 Part Number
R-32S-2 7/8 R-34S-MPB R-34S-1 7/8 R-34S-2 1/8 R-34S-2 3/8 R-34S-2 7/8 R-36S-MPB R-36S-1 7/8 R-36S-2 1/8 R-36S-2 3/8 R-36S-2 7/8 R-38S-MPB R-38S-1 7/8 R-38S-2 1/8
Sprockets with MPB (Minimum Plain Bore) are specified when the sprocket does not allow room for a bushing that will handle the maximum load.
EAGLE PD ACCULINEAR
SYNCHRONOUS APPLICATIONS Eagle Pd Acculinear belts can be used in open-end or spliced configurations in a variety of applications. Typical applications for the open-end configuration are in linear motion devices and other drives where precise motion is required. Typical application for the spliced configuration are in light conveyors and other material processing and transfer industries.
Part No: Y-8-PU-16-STD Y Alphabetical designation denotes belt width (Y=16 mm wide belt) 8 800 mm belt length PU Polyurethane 16 Belt width (16 mm) STD Standard construction Belt Length 800 mm Belt Type Open-end (or Spliced)
KEY FEATURES & BENEFITS Polyurethane material resists flaking, has higher dimensional stability and superior wear & abrasion resistance. Self-tracking and compact drives. Less vibration and reduced noise. High flexibility. High Precision linear positioning.
COMPACT DRIVES
When it comes to performance, Eagle Pd Acculinear belts and sprockets are right on track. The key to success lies in the systems patented H.O.T. geometry. With this self-tracking configuration, the sprockets left and right helixes guide the thermoplastic polyurethane belt to the center of the Eagle Pd sprocket. And there it remains: no waste, no wander, just improved efficiency and wear resistance in a compact design.
SELF-TRACKING SPROCKET
The H.O.T. geometry eliminates belt wander and the need for flanges. As a result, Eagle Pd sprockets can be used on slider bed applications where flanges would normally protrude above the bed surface.
LOW VIBRATION
Eagle Pd and the H.O.T. design minimize belt vibration on flat pulleys used on the entry and exit of slider beds. The belt moves progressively over straight edges, reducing noise and vibration. The tooth geometry eliminates the chordal effect that occurs around the tooth sprocket and reduces drive vibration.
13
EAGLE PD ACCULINEAR
OPEN-END BELT CONFIGURATION
Eagle Pd Acculinear belts are manufactured in open-end rolls with a standard roll length of 300 feet. The belt is manufactured with the tension members lying parallel to the belt edge so that the load is equally distributed across all tension members. A common application of open-end belts is in linear motion drives. Clamping plates are available for open-end Eagle Pd Acculinear belts to mechanically join the belts ends.
14
SYNCHRONOUS
PU for Polyurethane
Belt Width in mm
SPROCKETS
Eagle Pd Sprockets for the polyurethane belt line are available for all eight belt widths in a wide range of diameters. The Eagle Pd Acculinear product shares the same sprockets as the rubber Eagle Pd product. The only exception is with the M (25mm width) and the L (50mm width) sprockets. These two widths are stocked in Aluminum and are offered in a limited size range. All other sprocket widths are stocked either in ductile or cast iron. Refer to the Eagle Pd Sprocket section for more information.
1:
8 8 8 8 14 14 14 14
PU PU PU PU PU PU PU PU -
16 25 32 50 35 52.5 70 105
State Belt Pitch Length State Open-end or Spliced State Belt Construction
2: M 3: W 4: 5: 6: 7: 8: L B G 0 R
1 2
TENAX is a registered trademark of Tenax Fibers GmbH & Co. Kg LINATEX is a registered trademark of Linatex Limited
EAGLE PD ACCULINEAR
GOODYEARS POLYURETHANE WEB SITE WWW.ACCUBELT.COM
The Web site for Goodyears polyurethane products is a comprehensive one-stop location for information and product-related resources. The Web site is constantly updated with the latest news and product updates. It provides complete information on all aspects of the drive system: the belt, sprockets, clamping plates, special constructions, tensioning, application information, etc. Product-related engineering manuals and other resources can be easily viewed or downloaded in PDF file format. SYNCHRONOUS
15
EAGLE PD ACCULINEAR
Eagle Pd Sprockets for 25mm wide belt
Sprocket Face Width = 26 mm, Pitch = 8 mm
Sprocket Bore Range (inches) Part Number Hub* MIN. MAX. M-20S-MPB MPB 0.5000 1.0630 M-22S-MPB MPB 0.5000 1.2200 M-24S-MPB MPB 0.5000 1.3390 M-26S-MPB MPB 0.5000 1.5350 M-28S-MPB MPB 0.5000 1.6140 M-30S-MPB MPB 0.5000 1.7720 M-32S-MPB MPB 0.5000 1.8900 M-34S-MPB MPB 0.5000 2.0080 M-36S-MPB MPB 0.5000 2.1650 M-38S-MPB MPB 0.5000 2.2830 M-40S-MPB MPB 0.5000 2.4410 M-56S-MPB** MPB 0.5000 3.5040 M-90S-MPB** MPB 1.0000 2.8740 **These sprocket sizes are non-stock items. No. of Teeth 20 22 24 26 28 30 32 34 36 38 40 56 90 Pitch Diameter Type* (inches) 1 2.0050 1 2.2060 1 2.4060 1 2.6070 1 2.8070 1 3.0080 1 3.2080 1 3.4090 1 3.6090 1 3.8100 1 4.0100 1 5.6140 2 9.0230 O 1.9508 2.1513 2.3518 2.5523 2.7528 2.9533 3.1538 3.3543 3.5549 3.7554 3.9559 5.5600 8.9686 I E H T L Material 1.5000 1.5000 1.6500 1.6500 1.6500 1.6500 1.6500 1.6500 1.6500 1.6500 1.6500 1.6500 1.6500 Al Al Al Al Al Al Al Al Al Al Al Al AI Wt. (lbs) 0.33 0.41 0.55 0.68 0.80 0.93 1.08 1.23 1.40 1.57 1.75 3.53 5.29 Approx. WR2 (lbs.-ft2) 0.0009 0.0015 0.0023 0.0034 0.0047 0.0063 0.0083 0.0108 0.0138 0.0174 0.0217 0.0903 0.2867
16
SYNCHRONOUS
(inches) (Refer to Type I below) 0.4700 1.6000 0.4700 1.8100 0.6300 2.0100 0.6300 2.2800 0.6300 2.4400 0.6300 2.6400 0.6300 2.8300 0.6300 3.0300 0.6300 3.2300 0.6300 3.4300 0.6300 3.6200 0.6300 5.2400 8.0299 0.6300 4.7200 0.3150
NOTES: 1. Al = Aluminum (anodized). 2. Sprockets are only available in MPB. 3. The L(50 mm width) and M (25 mm width) belts and sprockets are non-stock items which need to be quoted and may have a longer lead time. 4. Sprocket dimensions and material are subject to change. 5. Please contact Goodyear for sprocket sizes and materials not listed in this manual. LH is the left-hand helix. RH is the right-hand helix. Note: For proper installation, orientation of teeth must be in the same direction on all sprockets in the drive.
LH
RH
*TYPE I
EAGLE PD ACCULINEAR
ACCULINEAR CLAMPING PLATES
SYNCHRONOUS
Part Number Eagle Pd 8mm Clamping Plate Eagle Pd 14mm Clamping Plate
Clamping Plates are available for Eagle Pd Acculinear Open-end belts to allow them to be used in Linear Motion Devices.
A L
Clamping Plates Belts 1: 2: 3: 4: 5: 6: 7: 8: Y-8-PU-16 M-8-PU-25 W-8-PU-32 L-8-PU-50 B-14-PU-35 A-14-PU-52.5 O-14-PU-70 R-14-PU-105 A (mm) 12 12 12 12 18 18 18 18 B (mm) 75 75 75 75 130 130 130 130 L (mm) 120 120 120 120 200 200 200 200 Material AL AL AL AL AL AL AL AL
AL = Aluminum
17
BLACKHAWK PD
APPLICATIONS Nearly every conceivable industrial drive application where precise shaft synchronization is required. BlackHawk Pd belts can also be used as an alternative to problem V-belt and chain drives. Aggregate Machinery Office Equipment Paper Industry Machinery Machine Tool Printing Trade Machinery Home Appliances Food Processing Equipment HVAC Units Packaging Machinery Textile Machinery Mining Equipment Farm Machinery Woodworking Machinery Vending Machines KEY FEATURES & BENEFITS Universal tooth profile drops into existing HTD and RPP sprockets. Quieter operation. High-grade Hibrex compound. Flexten tensile members provide excellent dimensional stability and high impact strength. Requires little, if any, retensioning and less drive maintenance. Oil, heat, ozone, and abrasion resistant. Designed for high-capacity performance. Higher horsepower rating and longer life than traditional timing belts. SYNCHRONOUS
Part No: 480 8M BH 12 480 480mm Pitch Length 8M 8mm Pitch BH BlackHawk Belt 12 12mm wide
Designed for higher loads and abrasion resistance, Plioguard facing provides a reduced coefficient of friction so that the belt meshes easier with sprockets. The nylon facing is enhanced with Hibrex which can provide 6 to 7% better abrasion resistance. The demands of synchronous drives put additional strain on the belt and tooth surface, for high speed and low speed applications. The BlackHawk Pd tooth profile resists ratcheting and provides accurate positioning for synchronous drive applications. Upgraded Hibrex materials and tooth profile enable the teeth to engage the sprocket smoothly.
18
2.3mm
3mm Pitch
BLACKHAWK PD
10.7mm 14mm Pitch
5.7mm
Available Sizes PITCH LENGTH (mm) 480 536* 14mm Pitch 560 600 640 680* 720 800 840* 856* 880 896* 960 968* 1040 1056* 1120 1184* 1200 1248* 13.8mm 1280 1320* 1400* 1440 1600 1760 1800 1904* 2104* 2000 2400 2600 2800 3048 20mm Pitch 3280 3600 4400
Available Sizes PITCH LENGTH (mm) 966 1190 1400 1610 1778 1890 2100 2310
10.7mm
13.8mm
Stock Widths: 20mm, 30mm, 50mm, 85mm *Nonstock, made to order. Minimum quantities required.
BLACKHAWK PD SPROCKETS
SPROCKET TYPES The following types of sprockets are available for BlackHawk Pd Belts. Sketches are shown with the Sure-Grip bushing in place.
TYPE A
TYPE B
TYPE C
TYPE D
TYPE E
TYPE MPB
TYPE L
TYPE AF
TYPE BF
TYPE CF
TYPE DF
TYPE EF
TYPE LF
The figure following the sketch reference letter in the Type column indicates the construction of the sprocket (1=Solid, 2=Web, and 3=Arms), and the letter F indicates that the sprocket has flanges.
FOR FULL PRODUCT AVAILABILITY AND SPECIFICATIONS, PLEASE VISIT WWW.GOODYEARPTP.COM OR CONTACT A GOODYEAR REPRESENTATIVE.
19
SYNCHRONOUS
8M
14M
WHITEHAWK PD
APPLICATIONS Nearly every conceivable industrial drive application where precise shaft synchronization is required. WhiteHawk Pd belts can also be used as an alternative to problem V-belt and chain drives. Aggregate Machinery Office Equipment Paper Industry Machinery Machine Tool Printing Trade Machinery Home Appliances Food Processing Equipment HVAC Units Packaging Machinery Textile Machinery Mining Equipment Farm Machinery Woodworking Machinery Vending Machines KEY FEATURES & BENEFITS Universal tooth profile drops into existing HTD sprockets. Quieter operation. High-grade Hibrex compound. Requires little, if any, retensioning and less drive maintenance. Oil, heat, ozone, and abrasion resistant. Designed for high-capacity performance. Higher horsepower rating and longer life than traditional timing belts. SYNCHRONOUS
Part No: 966 14M WH 20 966 966mm Pitch Length 14M 14mm Pitch WH WhiteHawk Belt 20 20mm wide
20
2.3mm
WHITEHAWK PD
5.7mm 8mm Pitch
3mm Pitch
5.7mm
Available Sizes PITCH LENGTH IN MILLIMETERS 480 536* 14mm Pitch 560 600 640 680* 720 800 840* 856* 880 896* 960 968* 1040 1056* 1120 1184* 1200 1248* 1280 13.8mm 1320* 1400* 1440 1600 1760 1800 1904* 2104* 2000 2400 2600 2800 3048 20mm 3280 Pitch 3600 4400
Available Sizes 966 1190 1400 1610 1778 1890 2100 2310
10.7mm
14mm Pitch
PITCH LENGTH IN MILLIMETERS 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956 5320 5740 6160 6860
10.7mm
13.8mm
Stock Widths: 20mm, 30mm, 50mm, 85mm *Nonstock, made to order. Minimum quantities required.
FOR FULL PRODUCT AVAILABILITY AND SPECIFICATIONS, PLEASE VISIT WWW.GOODYEARPTP.COM OR CONTACT A GOODYEAR REPRESENTATIVE.
21
SYNCHRONOUS
8M
14M
WHITEHAWK PD
SYNCHRONOUS QD SPROCKET DIMENSIONS
SYNCHRONOUS SPROCKET TYPES The following types of sprockets are available for WhiteHawk Pd Belts. Sketches are shown with the Sure-Grip1 bushing in place.
TYPE A TYPE B TYPE C TYPE D TYPE E TYPE MPB TYPE L
TYPE AF
TYPE BF
TYPE CF
TYPE DF
TYPE EF
TYPE LF
The figure following the sketch reference letter in the Type column indicates the construction of the sprocket (1=Solid, 2=Web, and 3=Arms), and the letter F indicates that the sprocket has flanges.
TYPE AF
TYPE BF
TYPE CF
The figure following the sketch reference letter in the Type column indicates the construction of the sprocket (1=Solid, 2=Web, and 3=Arms), and the letter F indicates that the sprocket has flanges. FOR FULL PRODUCT AVAILABILITY AND SPECIFICATIONS, PLEASE VISIT WWW.GOODYEARPTP.COM OR CONTACT A GOODYEAR REPRESENTATIVE.
1 2
SURE-GRIP is a registered trademark of TB WOODS Incorporated TAPER-LOCK is a registered trademark of Reliance Electric Company
22
HI-PERFORMANCE PD PLUS
SYNCHRONOUS APPLICATIONS Nearly every conceivable industrial drive application where precise shaft synchronization is required. HPPD Plus belts can also be used as an alternative to problem V-belt and chain drives.
Part No: 800 8M 50 800 800 mm Pitch Length 8M 8 mm Pitch, Round Tooth Profile 50 50 mm Wide
Aggregate Machinery Paper Industry Machinery Printing Trade Machinery Food Processing Equipment Packaging Machinery Mining Equipment Woodworking Machinery
Office Equipment Machine Tools Home Appliances HVAC Units Textile Machinery Farm Machinery Vending Machines
KEY FEATURES & BENEFITS Universal tooth profile drops into existing HTD sprockets. Quieter operation. High-grade Wingprene compound. Higher Horsepower Plus construction in 5M, 8M, and 14M pitches. Fiberglass tension cords for excellent resistance to shrinkage/elongation. Oil, heat, ozone, and abrasion resistant. Low-maintenance/high-efficiency rating.
sprocket, belt performance is improved along with assuring longer belt life. The tension-carrying member in HPPD Plus belts is twisted from multiple strands of fiberglass cord, high in tensile strength, flex life and resistance to elongation. This results in excellent dimensional stability which prevents belt shrinkage or stretch under load. Take-up allowances are greatly reduced or eliminated, promoting a more maintenance-free drive. All HPPD Plus belts are made with Goodyears Wingprene polymer which is specially compounded to resist damaging environmental factors that can shorten belt life. HPPD Plus utilizes a stretch nylon facing specially developed by Goodyear. It reduces friction, minimizing wear on both belts and pulleys while contributing to smooth, precise operation, all contributing to extended belt life.
23
HI-PERFORMANCE PD PLUS
3M
Available Sizes Pitch Length in Millimeters 159* 177* 204* 252* 264* 312* 612* 633*
2.3mm
3mm Pitch
675* 738*
5M
10.7mm
24
SYNCHRONOUS
8M
350 Pitch 375 400 5.7mm 8mm Pitch 425 450 *Nonstock, made to order. Minimum quantities required. 3.6mm 5mm Pitch 475 500 535 2.3mm 10.7mm 3mm 14mm Pitch 565 Pitch 600 10.7mm 635 14mm Pitch
1270 670 710 1420 740 1595 800 1690 850 1790 1895 890 5.7mm 8mm Pitch 2000 950 1000 1050 2.3mm 3mm 1125 Pitch 1195
3.6m
Pitch
Available Sizes Pitch Length in Millimeters 1040 480 1056* 536* 14mm Pitch 1120 560 1184* 600 1200 640 1248* 680* 13.8mm 1280 720 1320* 800 1400* 840* 2.3mm 3mm 1440 856* Pitch 880 1600 896* 1760 960 1800 968* 1904* 2104* 2000 2400 2600 2800 3048 20mm Pitch3280 3.6mm 5mm Pitch 3600 4400
14M
Available Sizes 966 1190 1400 1610 1778 1890 2100 2310
13.8mm
20mm Pitch
14mm Pitch
5.7mm 8
10.7mm
Pitch Length in Millimeters 2450 2590 2800 3150 3360 3500 3850 4326 4578 4956 5320 5740 6160 6860
13.8mm
2 P
Stock Widths: 20mm, 30mm, 50mm, 85mm *Nonstock, made to order. Minimum quantities required.
10.7mm 14mm Pitch
20M
Available Sizes Pitch Length in Millimeters 2000 2500 3400 3800 4200 4600 5000 5200
13.8mm
20mm Pitch
HI-PERFORMANCE PD PLUS
SYNCHRONOUS QD SPROCKET DIMENSIONS
SPROCKET TYPES The following types of sprockets are available for HPPD+ Belts. Sketches are shown with the Sure-Grip1 bushing in place.
TYPE A TYPE B TYPE C TYPE D TYPE E TYPE MPB TYPE L
TYPE AF
TYPE BF
TYPE CF
TYPE DF
TYPE EF
TYPE LF
The figure following the sketch reference letter in the Type column indicates the construction of the sprocket (1=Solid, 2=Web, and 3=Arms), and the letter F indicates that the sprocket has flanges. Note: Type L and Type LF are not available in 5M.
TYPE AF
TYPE BF
TYPE CF
The figure following the sketch reference letter in the Type column indicates the construction of the sprocket (1=Solid, 2=Web, and 3=Arms), and the letter F indicates that the sprocket has flanges. Note: Synchronous Taper-Lock available for 8M and 14M sizes only. FOR FULL PRODUCT AVAILABILITY AND SPECIFICATIONS, PLEASE VISIT WWW.GOODYEARPTP.COM OR CONTACT A GOODYEAR REPRESENTATIVE.
1 2
SURE-GRIP is a registered trademark of TB WOODS Incorporated TAPER-LOCK is a registered trademark of Reliance Electric Company
25
SYNCHRONOUS
POSITIVE DRIVE PD
APPLICATIONS Nearly every conceivable industrial drive application where precise shaft synchronization is required. Positive Drive belts can also be used as an alternative to problem V-belt and chain drives.
Part No: 100 XL 025 100 10.0" Pitch Length XL Pitch-Trapezoidal Tooth Profile 025 .25" Wide
26
SYNCHRONOUS
Aggregate Machinery Chain Drives Packaging Machinery Paper Industry Machinery Food Processing Equipment Printing Trade Machinery Woodworking Machinery
Office Equipment Machine Tools Farm Machinery Home Appliances Textile Machinery Mining Equipment
KEY FEATURES & BENEFITS Universal trapezoidal tooth profiles drop into existing sprockets. High-grade Wingprene compound. Fiberglass tension cords for excellent resistance to shrinkage/elongation. Oil, heat, ozone, and abrasion resistant. Low-maintenance/high-efficiency rating.
POSITIVE DRIVE PD
MXL
(MINI EXTRA LIGHT)
0.045" 0.16" 0.500" Pitch
0.045"
0.045" 0.16"
XL
(EXTRA LIGHT)
0.09" 0.200" Pitch
0.080" Pitch
(LIGHT)
0.14"
0.080" Pitch
For small business machines, office 0.09" equipment, electric equipment, etc. 0.14" 1/12" Pitch Pitch Standard Part Numbers 40mxl 44mxl 48mxl 64mxl 72mxl
0.62" 0.200" 0.375" Pitch
For business machines, instruments, For fraction power-rated motor applisound equipment, etc. 0.44" cations such as in-home appliances, 0.44" small tools, pumps, blowers, etc. 1/5" Pitch Pitch Standard Part Numbers 60xl 0.62" 70xl 80xl 90xl 100xl 110xl 120xl 130xl 140xl 0.045" 150xl 160xl 170xl 0.080" 180xl Pitch 190xl 200xl 210xl 220xl 230xl 240xl 250xl 260xl 280xl 290xl 300xl 310xl 330xl
0.875" 0.875" Pitch
0.375" Pitch
0.375" Pitch
80mxl 0.44"
140mxl 168mxl
0.875" Pitch
Stock Widths* 1/8 inch = 012 3/16 inch = 019 1.250" 1/4 inch = 025 Pitch
370xl0.62" 380xl 1.250" 390xl Pitch 400xl 450xl 460xl 630xl 770xl
0.16" 0.500" Pitch
124l
187l Pitch 210l 0.080" 225l Pitch 240l 255l 0.09" 270l 285l
0.200"
300l 322l 0.16" 345l 367l0.500" 390lPitch 420l 450l 0.14" 480l 510l
0.375"
Stock Pitch Widths* 1/2 inch = 050 Pitch 3/4 inch = 075 1 inch = 100 0.44"
0.875" Pitch
0.14" Stock 0.09" Widths* 1/4 inch = 025 3/8 inch = 037
H
0.045" 0.080" Pitch 0.09" 0.200" Pitch 0.44"
(HEAVY)
0.200" 0.375" XHPitch (EXTRA HEAVY) Pitch 0.44" 0.875" Pitch 0.62"
For machine tools, pumps, fans, presses, motor generator sets, etc. 0.14" 1/2" Pitch Standard Part Numbers 210h 230h 240h 270h 0.875" 300h Pitch 330h 360h 390h 420h 450h 1.250"
0.375" Pitch 480h
For medium torque applications on heavy industrial equipment. 7/8" 1.250" Pitch Pitch Standard Part Numbers 507xh 560xh 630xh 700xh 770xh 840xh 980xh 1120xh 1260xh 1400xh 1540xh 1750xh
For high torque applications on heavy industrial equipment. 1-1/4" Pitch Standard Part Numbers 700xxh 800xxh 900xxh 1000xxh 1200xxh 1400xxh 1600xxh 1800xxh
0.62"
Pitch Stock Widths* 3/4 inch = 075 1 inch = 100 1-1/2 inch = 150 2 inches = 200 3 inches = 300
Stock Widths* 2 inches = 200 3 inches = 300 4 inches = 400 5 inches = 500
* Stock Widths: Use the three-digit size number as a suffix to the belt number when ordering. Note: For nonstock sizes, contact your local Goodyear Industrial Products Distributor.
27
SYNCHRONOUS
POSITIVE DRIVE PD
TIMING SPROCKET DIMENSIONS
The timing sprockets for XL Positive Drive Pd belts are all carried in stock with a minimum plain bore only but can be re-bored to any size within the bore range. Constructions are available with solid (no web) or with web. Sprockets are also available with or without flanges. SYNCHRONOUS
SPROCKET TYPES The following types of sprockets are available for Positive Drive Pd belts. Sketches are shown with the Sure-Grip1 bushing in place. Sprockets are available either solid, with webs, or with arms. They are also available with or without flanges.
TYPE C TYPE D TYPE E TYPE MPB
TYPE CF
TYPE DF
TYPE EF
Note: Above sprockets are available for L, H, XH, and XXH belts.
FOR FULL PRODUCT AVAILABILITY AND SPECIFICATIONS, PLEASE VISIT WWW.GOODYEARPTP.COM OR CONTACT A GOODYEAR REPRESENTATIVE.
1
28
SUPER TORQUE PD
SYNCHRONOUS APPLICATIONS Nearly every conceivable industrial drive application where precise shaft synchronization is required. Super Torque Pd belts can also be used as an alternative to problem V-belt and chain drives.
Part No: 100S4.5M175 100 10 mm Width S Super Torque Positive Drive Belt 4.5M 4.5 mm Pitch Modified Round Tooth Profile 175 175 mm Pitch Length
Milling Machines Engine Accessory Drives Internal Combustion Engines Timers or Controllers Compressors Wood Chippers Conveyors Debarkers Lathes Shapers Textile Machinery Mixers
KEY FEATURES & BENEFITS Unique tooth profile for quiet tooth engagement. Improved horsepower capacity over standard HTD profiles. High-grade Wingprene compound. Fiberglass tension cords for excellent resistance to shrinkage/elongation. Oil, heat, ozone, and abrasion resistant. Mating sprockets required. Low-maintenance/high-efficiency rating.
29
SUPER TORQUE PD
S3M
SYNCHRONOUS
3mm Pitch 3mm
Pitch 8mm Pitch Pitch
1.9mm
3mm Pitch
Part No. Number of Teeth S3M120 40 S3M150 50 S3M177 59 S3M201 2.8mm 4.5mm 67 Pitch 75 S3M225 Part No. Number of Teeth S4.5M175 39 S4.5M180 40 S4.5M225 50 Part Number
5mm Pitch
Part Number S3M252 S3M264 S3M276 S3M300 S3M339 Part Number S4.5M247 S4.5M297 Part Number S5M475 S5M500 S5M525 S5M560 S5M575 S5M600 S5M625 S5M650 S5M675 Part Number S8M824 S8M840 S8M848 S8M880 S8M896 S8M920 S8M928 S8M936 S8M944 S8M960 S8M976 S8M984 S8M992 S8M1000 S8M1024 S8M1032 S8M1040 S8M1056 S8M1072 S8M1096
No. of Teeth 84 88 92 100 113 No. of Teeth 55 66 No. of Teeth 95 100 105 112 115 120 125 130 135 No. of Teeth 103 105 106 110 112 115 116 117 118 120 122 123 124 125 128 129 130 132 134 137
S4.5M
5.3mm 2.8mm
2.8mm
mm
mm
Part No. Number of Teeth S4.5M306 68 S4.5M342 76 Part Number S5M700 S5M750 S5M800 S5M850 S5M900 S5M950 S5M1000 S5M1050 S5M1125 Part Number S8M1120 S8M1136 S8M1160 S8M1176 S8M1184 S8M1200 S8M1208 S8M1224 S8M1248 S8M1256 S8M1264 S8M1280 S8M1304 S8M1312 S8M1360 S8M1384 S8M1400 S8M1432 S8M1440 S8M1480 No. of Teeth 140 150 160 170 180 190 200 210 225 No. of Teeth 140 142 145 147 148 150 151 153 156 157 158 160 163 164 170 173 175 179 180 185
Part No. Number of Teeth S4.5M504 112 S4.5M621 138 Part Number S5M1270 S5M1350 S5M1420 S5M1800 S5M2000 S5M2770 No. of Teeth 254 270 284 360 400 554
3.4mm
S5M
3.4mm
3.4mm
No. of Teeth 51 59 65 70 75 80 85 87 90
S5M255 S5M295 S5M325 14mm S5M350 Pitch S5M375 S5M400 S5M425 S5M435 S5M450
4.5mm
1.9mm
10.2mm
S8M
2.8mm
Part Number S8M1488 S8M1544 S8M1552 S8M1600 S8M1680 S8M1696 S8M1760 S8M1800 S8M2000 S8M2032 S8M2240 S8M2272 S8M2392 S8M2400 S8M2496 S8M2600 S8M2800 S8M3200
No. of Teeth 186 193 194 200 210 212 220 225 250 254 280 284 299 300 312 325 350 400
1.9mm
5.3mm
S8M440 S8M448 S8M480 S8M496 8mm 5.3mm S8M512 Pitch 3.4mm 5mm S8M528 Pitch S8M560 S8M576 S8M592 S8M600 S8M632 S8M648 14mm 10.2mm S8M656 Pitch S8M680 3mm S8M688 2.8mm 4.5mm Pitch Pitch S8M712 S8M720 S8M752 S8M760 S8M800 8mm
Pitch
S14M
10.2mm
3.4mm
5mm Pitch
14mm Pitch
Part No. Number of Teeth S14M1120 80 S14M1190 85 S14M1400 100 S14M1540 110 S14M1610 115
Part No. Number of Teeth S14M1778 127 S14M1890 135 S14M2002 143 S14M2100 150 S14M2240 160
Part No. Number of Teeth S14M2310 165 S14M2450 175 S14M2590 185 S14M2800 200 S14M3150 225
Part No. Number of Teeth S14M3500 250 S14M3850 275 S14M4004 286 S14M4508 322 S14M5012 358
Note: All Super Torque belts are nonstock. Standard factory lead times will apply. Mandrel quantity minimums apply. Other sizes available upon request.
30
DUAL HI-PERFORMANCE PD
Part No: D10408M20 D Dual Sided 1040 1040 mm Pitch Length 8M 8 mm Pitch Round Tooth Profile 20 20 mm Wide
KEY FEATURES & BENEFITS Dual-sided teeth versatility in 8M, 14M, XL, L and H profiles. Universal tooth profiles drop into existing sprockets. High-grade Wingprene compound. Fiberglass tension cords for excellent resistance to shrinkage/elongation. More compact drive designs. Oil, heat, ozone, and abrasion resistant.
31
XL 8M
Part Number No. of Teeth
8mm
Part Number
8mm Pitch
No. of Teeth
(EXTRA LIGHT)
1/5-inch pitch For business machines, instruments, sound equipment, etc.
0.120"
0.200" Pitch
D720 8M D800 8M D880 8M D960 8M D1040 8M D1120 8M D1200 8M D1280 8M D1440 8M D1600 8M D1760 8M
90 D1800 8M 225 100 D2000 8M 250 14mm 110 14.6mm D2400 8M 300 Pitch 120 D2600 8M 325 130 D2800 8M 350 140 D3048 8M 381 150 D3280 8M 410 160 D3600 8M 450 180 D4400 8M 550 200 Available in 20, 30, 50 & 220 85 mm widths.
XL Part Numbers D290XL D170XL D60XL D300XL D180XL D70XL 0.375" 0.180" D310XL D190XL D80XL Pitch D330XL D200XL D90XL D362XL D210XL D100XL D392XL D220XL D110XL D450XL D230XL D120XL D492XL D240XL D130XL 0.500" 0.234" D690XL D250XL D140XL Pitch D900XL D260XL D150XL D280XL D160XL
Stock0.120" 1/4 inch=025, 3/8 inch=037 Widths*
0.200" Pitch
L
(LIGHT)
3/8-inch pitch For fraction power-rated motor applications such as in-home appliances, small tools, pumps, etc.
8mm
8mm Pitch
D124L 0.234"
14M
Part Number
14.6mm
No. of Teeth Part Number
14mm Pitch
No. of Teeth
L Part Numbers D480L D300L D510L D322L D150L 0.500" D540L D345L D187L Pitch D600L D367L D210L 0.120" D660L D390L D225L D420L Pitch D270L 0.200" D450L D285L
0.375" Pitch
D1400 14M D1610 14M D1778 14M D1890 14M D2100 14M D2450 14M D3150 14M
D3500 14M D3850 14M D4326 14M D4578 14M D6160 14M
H
(HEAVY)
1/2-inch pitch For machine tools, pumps, fans, presses, motor generator sets, etc.
H Part Numbers D750H D480H D800H D510H D850H D540H D900H D570H D1000H D600H D1250H D630H D1400H D660H D1700H D700H
*Stock Widths: Use the three-digit size number as a suffix to the belt number when ordering. For nonstock sizes, contact your local Goodyear Industrial Products Distributor. Note: Other sizes available upon request.
32
OPEN END PD
APPLICATIONS For synchronized applications.
Elevation Mechanisms Linear Motion Drives Open/Close Mechanisms Reciprocating Drives Replaces Chain Applications Synchronized Tracking
Positioning Drives Metering Drives Conveying Drives Reversing Drives Fixed Center Drives
KEY FEATURES & BENEFITS Wide load range available from various cross sections. High power-to-weight ratio allows for lighter metallic or nonmetallic pulleys for greater weight savings. Provides space-saving design opportunities using small pulleys, short centers, and narrow belts. Smooth engagement of belt and pulley eliminates chatter and vibration. Low noise improves aesthetic acceptance of equipment. Requires no lubrication or retensioning. Minimal backlash for system security.
33
SYNCHRONOUS
0.045"
0.045" 0.045"
POSITIVE DRIVE
MXL
0.045" 0.16"
0.500" 0.500" 0.080" 0.080" Pitch Pitch (TRAPEZOIDAL TOOTH) Pitch Pitch
OPEN END PD
L 0.14" 0.14"
0.045" 0.375" 0.080" 0.375" Pitch Pitch Pitch 0.16" 0.500" Pitch
0.16" 0.16"
XL 0.09" 0.09"
0.200" 0.500" 0.200" PitchPitch Pitch
XHPitch
0.375"
10.7mm
34
SYNCHRONOUS
Part No.
Roll Length 0.14" Length Roll 0.44" 0.44" (ft) (mm) 753 230 0.375" 501 Pitch 153 375 114 249 76 0.62" 1072 0.62" 327 0.875" 854 260 Pitch 711 217 531 162 351 107
(ft)
0.200" 516 Pitch
MXL012 0.200" MXL019 Pitch MXL025 MXL037 0.44" XL025 XL031 XL037 XL050 XL075 0.62"
L075 L100 H037 0.44" H050 1.250" H062 1.250" Pitch H075 Pitch H100
0.62"
H150 212 0.375" H200 157 Pitch H250 103 H300 76 XH075 226 XH100 168 0.875" 133 XH200 Pitch 110 3.6mm 5mm Pitch 81
1.250" Pitch
3.6mm 5m
2.3mm
5M
3.6mm 5mm Pitch
3.6mm 5mm Pitch
1.250" Pitch
8M
10.7mm
14M
14mm Pitch
Part No.
10.7mm 8M10 285 87 14mm Pitch 633 5.7mm 8mm Pitch 8M15 420 190 58 8M20 312 935 285 246 8mm Pitch8M25 620 189 5.7mm 8M30 203 367 112 1.9mm66 3mm 13.8mm 8M40 2.8mm 4.5mm151 217 Pitch 8M50 Pitch 92
Roll Length Roll Length 2.8mm (ft) (mm) 4.5mm 56 308 184 128 75 49
Pitch
17 94 56 39 23 15
13.8mm
20mm Pitch
14mm Pitch
Pitch
(ROUND TOOTH)
5mm Pitch
S4.5M 20mm
Pitch
S5M
3.4mm 5mm Pitch
5.3mm
S8M
8mm Pitch
S14M
10.2mm 3.4mm 5mm Roll Length Pitch
14mm Pitch
13.8mm 5.3mm
Part No.
Part No.
Roll Length (ft) 627 413 246 633 420 358 312
Part No.
(ft)
50S3M 289 88 60S3M 240 73 90S3M 8mm 157 48 5.3mm 8mm 5.3mm 100S3M 44 10.2mm Pitch 144 Pitch 3.4mm 5mm 3.4mm 5mm 60S45M 236 72 Pitch Pitch 100S45M 141 43 60S5M 1050 320
250S8M 246 300S8M 203 350S8M 174 400S8M 151 14mm 400S14M Pitch 135 10.2mm 400S14M 95 400S14M 85
66 57 40
BUSHINGS
Sure-Grip1 Quick Detachable bushings are easy to install and remove. They are split through flange and taper to provide a true clamp on the shaft that is the equivalent of a shrink fit. All sizes except JA and QT have a setscrew over the key to help maintain the bushings position on the shaft until the cap screws are securely tightened. Sure-Grip bushings have a very gradual taper (3/4-inch taper per ft. on the diameter) which is about half the inclined angle of many other bushings. The result is that the Sure-Grip securely clamps the shaft, with twice the force of those competitive bushings, to provide extreme holding power. Versatile Sure-Grip bushings permit the mounting of the same mating part on shafts of different diameters, and the mounting of different sheaves on the same shaft using the same bushing. Their interchange ability extends through sheaves, pulleys, timing pulleys, sprockets, flexible and rigid couplings, madeto-order items by Goodyear, and to product lines of several other mechanical power transmission manufacturers. Sure-Grip bushings are manufactured with the drilled and tapped holes located at a precise distance from the keyseat; thus, a wide mating part having a bushing in each end can be mounted on a common shaft with the two keyways in line. This feature not only facilitates installation but also permits both bushings to carry an equal share of the load.
Saw cut through flange and taper (and sometimes cut down into keyway also) to provide a true clamp fit. Cap screws used to secure bushings to sheave and to remove bushing from sheave.
QT JA SH SDS SD SK SF E
F J M N P SKL SFL EL
SURE-GRIP IDLER BUSHINGS AND REPLACEMENT BEARINGS SH-BB SF-BB SD-BB E-BB SK-BB
METRIC SURE-GRIP BUSHINGS QTMX SKMX JAMX SFMX SHMX EMX SDSMX FMX SDMX
35
SYNCHRONOUS
6-hole drilling (most sizes) makes installation and removal quick and easy.
Precise taper (3/4 in. per ft. on diameter) provides proper wedging action.
36
POLY-V (V-RIBBED)
Poly-V belts are flat belts with a series of longitudinal ribs on the driving face that mate with grooves in the sheave rim. Relatively thin, with a well-supported tensile member, these belts perform better than V-belts on drives with small sheave, high speeds, reverse bends, and high-speed ratios. Poly-V belts generally run smoother than V-belts and their low weight makes them suitable for high-speed drives. Three cross sections, designated J, L and M, handle the same range of industrial applications as narrow or classical belts. A smaller section, H, is used for small sheave and miniature drives.
37
TORQUE TEAM
(LAMINATED)
APPLICATIONS Goodyear Torque Team Laminated V-belts are particularly effective when installed on drives that experience frequent slippage caused by logs and heavy lumber that jam or impact the equipment. Some of the most common drives recommended for consideration include:
Part No: 3/5VL800 3/ 3 Rib Joined Construction 5V .62" Top Width Narrow Profile Rib L Laminated Construction 800 80.0" Nominal Outside Length
KEY FEATURES & BENEFITS Narrow profile ribs provide savings through efficiency. Joined construction for problem drives. High horsepower capacity. High-strength Vytacord tensile members. Laminated Wingprene cushion engineered to slip. Tough fabric backing. Oil, heat, ozone, and abrasion resistant. Static conductive.
38
BANDED
Wrap it all up in Wingprene, Goodyears superior oil and heat resistant compound, and you have a power transmission belt made to withstand the most severe operating conditions.
*Stock items. For longer 5V, as well as 3V and 8V laminated profiles not listed here, contact Goodyears Customer Service Department-Lincoln.
strength to withstand the dynamic forces acting within a joined belt. The backing also has special adhesion characteristics that enable it to bond inseparably to the V-sections to maintain the unitary integrity of the belt. The cushion is made of a fiber-reinforced Wingprene compound, providing oil, heat, ozone and abrasion resistance.
39
BANDED
Part No: 3/8V1900 3/ 3 Rib Joined Construction 8V 1.00" Top Width Narrow Profile Rib 1900 190.0" Nominal Outside Length Single Envelope Ply on 5Vs 2 Envelope Plies on 8Vs Envelope Uncogged Construction Shown
CUT EDGE SIDE VIEW Part Number 3VX250 3VX265 3VX280 3VX300 3VX315 3VX335 3VX355 3VX375 Part Number 5VX500 5VX530 5VX560 5VX600 5VX630 5VX670 5VX710 5VX750 5VX800 Part Number 8V1000 8V1060 8V1120 8V1180 8V1250 8V1320 8V1400 8V1500 Max No. Ribs per Slab 90 90 90 90 90 90 90 90 Max No. Ribs per Slab 53 53 53 53 53 53 53 53 53 Max No. Ribs per Slab 14 14 14 14 24 24 24 24 Part Number 3VX400 3VX425 3VX450 3VX475 3VX500 3VX530 3VX560 3VX600 Part Number 5VX850 5VX900 5VX950 5VX1000 5VX1060 5VX1120 5VX1180 5V1250 Max No. Ribs per Slab 90 90 90 90 90 90 90 90 Max No. Ribs per Slab 53 53 53 53 53 53 53 42 Part Number 3VX630 3VX670 3VX710 3VX750 3VX800 3VX850 3VX900 3VX950 Part Number 5V1320 5V1400 5V1500 5V1600 5V1700 5V1800 5V1900 5V2000 5V2120 Part Number 8V2500 8V2650 8V2800 8V3000 8V3150 8V3350 8V3550 8V3750 Max No. Ribs per Slab 90 90 90 90 90 90 90 90 Max No. Ribs per Slab 42 42 42 42 42 42 42 42 42 Max No. Ribs per Slab 24 24 24 24 24 24 24 24 Part Number 3VX1000 3VX1060 3VX1120 3VX1180 3V1250 3V1320 3V1400 Max No. Ribs per Slab 90 90 90 90 74 74 74
Part Number 5V2240 5V2360 5V2500 5V2650 5V2800 5V3000 5V3150 5V3350 5V3550 Part Number 8V4000 8V4250 8V4500 8V4750 8V5000 8V5600 8V6000
Max No. Ribs per Slab 42 42 42 42 42 42 42 42 42 Max No. Ribs per Slab 24 24 24 24 24 24 24
Part Number 8V1600 8V1700 8V1800 8V1900 8V2000 8V2120 8V2240 8V2360
40
some very clear advantages, especially when you consider that you get these savings along with a dramatic performance advantage. There is also less weight because the smaller sheaves used for drives using Torque Team Plus belts are a dramatic 50% lighter than a sheave required to drive an equal horsepower multiple V-belt drive. When compared to an equal horsepower chain drive, the sheave weighs an incredible 65% less than the sprocket required for the chain drive. Torque Team Plus is more compact. In fact, a typical Torque Team Plus belt is only one-third the width of an equivalent multiple V-belt team. It needs 17% less space than an equivalent chain drive. And since Torque Team Plus belts give you all the advantages of the joined principal (smooth tracking, no belt turnover, no matching problems, less belt threatening vibration, even and consistent tensioning), there is less maintenance required.
41
BANDED
Part No: 3/5VF2000 3/ 3 Rib Joined Construction 5V 0.62" Top Width Narrow Profile Rib F Torque Team Plus With Flexten Tensile Member 2000 200.0" Nominal Outside Length Single Envelope Ply on 5Vs, 2 Envelope Plies on 8Vs
KEY FEATURES & BENEFITS Narrow profile ribs provide savings through efficiency. Joined construction for problem drives. Up to 50% more horsepower capacity. High-strength Flexten tensile members. Heavy fiber-loaded Wingprene cushion. Tough Wingprene impregnated backing. Oil, heat, ozone, and abrasion resistant. Unique Wingflex Envelope construction. Static conductive.
42
BANDED
Part Number
Max No. Ribs per Slab
Part Number
Part Number
42 42 42 42 42 42 42
42 42 42 42 42 42 42
42 42 42 42 42 42 42
42 42 42 42
Part Number
Part Number
Part Number
Part Number
24 24 24 24 24 24 24 24
24 24 24 24 24 24 24 24
24 24 24 24 24 24 24 24
24 24 24
Torque Team Plus was designed to belt a drive with one band. They are not to be used in matching sets.
3V
Available Sizes DIAMETER (in) 2.20 2.35 2.50 2.65 2.80 3.00 3.15 3.35 JA JA JA JA JA JA, SH JA, SH JA, SH 3.65 4.12 4.50 4.75 5.00 5.30 5.60 6.00 SH SH SH, SDS SH, SDS, SK SH, SDS, SK SH, SDS, SK SH, SDS, SK SH, SDS, SK 6.50 6.90 8.00 10.60 14.00 19.00 25.00 33.50 SH, SDS, SK SH, SDS, SK SDS, SK, SF SDS, SK, SF, E SK, SF, E SK, SF, E SF, E, F SF, E, F
5V
Available Sizes DIAMETER (in) 4.40 4.65 4.90 5.20 5.50 5.90 6.30 6.70 7.10 7.50 8.00 SH, SDS, SD SDS, SD SDS, SD SDS, SD SDS, SD SDS, SD, SK SK SK, SF SK, SF SK, SF SK, SF, E 8.50 9.00 9.25 9.75 10.30 10.90 11.30 11.80 12.50 13.20 14.20 SK, SF, E SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SF, E, F, J SF, E, F, J SF, E, F, J 15.00 16.00 18.70 21.20 23.60 28.00 31.50 37.50 50.00 SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J E, F, J, M E, F, J, M F, J, M F, J, M F, J, M
8V
Available Sizes DIAMETER (in) 12.50 13.20 14.00 15.00 16.00 17.00 18.00 F, J, M F, J, M F, J, M F, J, M F, J, M F, J, M F, J, M 19.00 20.00 21.20 22.40 24.80 30.00 35.50 F, J, M, N J, M, N J, M, N J, M, N M, N M, N, P M, N, P 40.00 44.50 53.00 63.00 71.00 M, N, P M, N, P M, N, P, W P, W P, W
43
BANDED
(CLASSICAL)
APPLICATIONS For shock load applications. Ideal for pulsating loads, high-capacity drives, and short center heavy-duty drives. KEY FEATURES & BENEFITS Classical profile ribs. Joined construction for problem drives. High-strength Vytacord tensile members. Available in cut-edge construction with Wingprene insulation or envelope construction with Plioflex cushion. Tough fabric backing. Oil, heat, ozone, and abrasion resistant. Matchmaker to eliminate mismatch. Static conductive.
Part No: 3/BX112 3/ 3 Rib Joined Construction B .66" Top Width Classical Profile Rib X Premium Cogged Construction 112 Approximate 112" Inside Length Cut-Edge, Molded Cog Construction Shown
44
BANDED
MATCHMAKER PERFORMANCE
Goodyears Matchmaker technology results in belt consistency run to run. That means each Hy-T Torque Team Classical belt is identical in size and performance to every other Hy-T Torque Team Classical belt in that size, no matter when or where it was produced. By eliminating mismatch problems, there is no costly and complicated belt matching to get a drive back on line; no problems with belts that are too tight or too loose.
(CLASSICAL)
B PROFILE Part Number BX35 BX38 BX42 BX43 BX46 BX48 BX50 BX51 BX52 BX53 BX54 BX55 BX56 BX57 BX58 BX59 BX60 BX61 Max No. Ribs per Slab 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 Part Number BX62 BX63 BX64 BX65 BX66 BX67 BX68 BX70 BX71 BX72 BX73 BX74 BX75 BX77 BX78 BX79 BX80 BX81 Max No. Ribs per Slab 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 Part Number BX82 BX83 BX84 BX85 BX87 BX88 BX90 BX93 BX95 BX96 BX97 BX99 BX100 BX103 BX105 BX108 BX112 B120 Max No. Ribs per Slab 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 49 38 Part Number B124 B128 B133 B136 B144 B148 B158 B162 B173 B180 B195 B210 B225 B240 B255 B270 B300 B315 Max No. Ribs per Slab 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 BANDED
Part Number CX60 CX68 CX75 CX81 CX85 CX90 CX96 CX99 CX100
Part Number CX105 CX108 CX109 CX112 C120 C124 C128 C136 C144
C PROFILE Max No. Part Ribs per Slab Number 36 36 36 36 14 26 26 26 26 C158 C162 C173 C180 C195 C210 C225 C240 C255
Part Number C270 C285 C300 C315 C330 C345 C360 C390 C420
D PROFILE Max No. Part Ribs per Slab Number 18 18 18 18 18 18 18 D315 D330 D345 D360 D390 D420 D450
45
A/B
Available Sizes DIAMETER (in) 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 SH, SD SH, SD SH, SD SH, SD SH, SD SH, SD SDS, SD SDS, SD SDS, SD SDS, SD SDS, SD, SK 5.6 5.8 6.0 6.2 6.4 6.6 6.8 7.0 7.4 8.0 8.6 SDS, SD, SK SDS, SD, SK SDS, SD, SK, SF SDS, SD, SK, SF SDS, SD, SK, SF SDS, SD, SK, SF SDS, SD, SK, SF SDS, SK, SF SDS, SK, SF SDS, SK, SF SDS, SK, SF, E 9.4 11.0 12.4 13.6 15.4 16.0 18.4 20.0 25.0 30.0 38.0 SDS, SK, SF, E SDS, SK, SF, E SDS, SK, SF, E SDS, SK, SF, E SK, SF, E, F SK, SF, E, F SK, SF, F SK, SF, E, F SF, E, F SF, E, F SF, E, F, J
46
BANDED
A/B
Available Sizes 5.6 6.0 6.8
(LARGE BORE)
C
Available Sizes DIAMETER (in) 5.0 5.6 6.0 7.0 7.5 8.0 8.5 9.0 SD SD SF SF SF SF, E SF, E SF, E, F, J 9.5 10.0 10.5 11.0 12.0 13.0 14.0 16.0 SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J 18.0 20.0 24.0 27.0 30.0 36.0 44.0 50.0 SF, E, F, J SF, E, J, M SF, E, F, J, M F, J F, J, M F, J, M F, J, M F, J, M
D
Available Sizes DIAMETER (in) 12.0 13.0 13.5 14.0 14.5 15.0 F, J, M F, J, M F, J, M F, J, M F, J, M F, J, M 15.5 16.0 17.0 18.0 20.0 22.0 F, J, M F, J, M J, M J, M J, M J, M 24.0 27.0 33.0 40.0 48.0 58.0 J, M J, M J, M, N J, M, N J, M, N, P M, N, P
POLY-V
APPLICATIONS For small sheave compact designs requiring limited vibration. Ideal for high-speed ratio drives with short center distances.
47
BANDED
Part No: 180J6 18.0" Nominal Outside Length J J Section Poly-V 6 6 Ribs
KEY FEATURES & BENEFITS Multiple V-ribbed profile provides friction and wedge advantages. High-grade Wingprene compounding. Strong Vytacord tensile member. Milled J & L cross sections, molded M cross section. Oil, heat, ozone, and abrasion resistant. Static conductive.
POLY-V
Stock Construction: No minimum quantity required. Can order any number of ribs up to maximum number of ribs per belt (Max Ribs/Belt) shown below.
H SECTION
.14" .14"
BANDED
0.092" 0.092"
"
200J 220J 240J .140" .140" 260J 280J 300J 320J 340J 360J 380J 400J .51" 430J .51" 460J 490J 520J 550J 0.370" 580J
K SECTION
.063"
0.370"
.140"
Part Number Max Ribs/Belt Part Number Max Ribs/Belt
500L 540L 560L 615L .51" 635L 655L 675L 695L 725L 0.370" 765L 780L 795L 815L 96 96 96 96 72 96 69 72 72 72 96 96 96 840L 865L 915L 975L 990L 1065L 1120L 1150L 1215L 1230L 1295L 1310L 1455L 96 72 72 96 72 96 96 96 72 72 72 72 72
092"
.12"
.38"
.063" .51" .165"
"
0.185" 0.370"
0.092" .140"
M SECTION
.51"
0.370"
Special Note: Special Manufacture Belts are available. *Please check factory for availability.
48
V-BELTS
V-belts include not only traditional classical and narrow profiled belts, but also Double-V and FHP belts. When synchronization or timing is not required, V-belts make an excellent low-cost, quiet and efficient means of transmitting power. However, not all V-belts perform the same. Depending on your application and your objectives, some V-belts will be better at getting you closer to your end goal.
CLASSICAL V-BELTS
The most widely used V-belts are A, B, C, and D classical belts. Used more out of habit and convenience than design, these belts can handle fractional to 500-hp drives, usually at the lowest cost. However, they occupy more space, and the drives weigh more than narrow-belt drives. Also, classical belts are usually less efficient than narrow belts. But their versatility and wide range of sizes and types make them an attractive alternative to wedge belts. Many classical belts are used for replacement because it is considered too costly to replace sheaves when upgrading from classical to narrow or other belt types. Therefore, when replacing classical sheaves, it is an opportune time to upgrade to narrow or other belt types. V-BELT belts is more complicated and Goodyears V-belt engineering manual should be consulted when replacing or troubleshooting these drives. singly on drives of 1 hp or less. under-designed or problem drives can be upgraded to satisfactory by substituting classical cogged belts for classical envelope belts without replacing sheaves. Because of their higher coefficient of friction, cogged belts tend to be more sensitive to alignment. While envelope belts can tolerate some misalignment, cogged belts are more likely to turn over under the same conditions. Cogged belts should not be used in clutching drives, drives with severe shock loads, and drives that have changing center distances, such as shaker screens. In these applications, the aggressive nature and flexibility of cogged belts can cause vibration, belt turnover, and belt breakage. Cogged belts should also be avoided in drives that require slippage during frequent stops and starts.
49
Part No: B-Open End B 0.66" Top Width Classical Profile Available Roll Lengths
HORSEPOWER RATINGS
The horsepower ratings for fastened Open End V-belts are approximately 30% of published horsepower ratings for Goodyears standard multiple V-belts as shown in Goodyears Multiple V-belt Engineering Manual (20044896). NOTE: Because of differences in the stretch characteristics and variations in cross section dimensions, Open End V-belts and Endless V-belts should not be used together on multiple drives.
Roll Lot: Either 250' (max. 2 pcs.) or 500' (max. 3 pcs.) approx. rolls. D section available only in 250' (max. 2 pcs.) approx. rolls.
50
HY-T WEDGE
APPLICATIONS Narrow profile belts for compact, high horsepower drives and high shock loading on short centers and small diameters. For designing compact, heavy-duty drives where space limitation is a factor. KEY FEATURES & BENEFITS Narrow profile provides savings through efficiency. Greater horsepower than the classical belt. Strong Vytacord (polyester) tensile members. Highgrade Wingprene compound. Oil, heat, ozone, and abrasion resistant. Available in raw-edge construction with cogs or envelope construction. Matchmaker to eliminate mismatch. Static conductive.
Part No: 5V1400 5V .62" Top Width Narrow Profile 1400 140.0" Nominal Outside Length Envelope Uncogged Construction Shown
The savings start in the basic wedge design of the Hy-T Wedge belt. It has a narrower cross section than standard V-belts so it distributes stresses more uniformly to deliver more consistent, more reliable power transmission. A narrower cross section means the belts are smaller and weigh less. Smaller belts allow for the use of smaller and lighter sheaves resulting in a more efficient drive. The savings continue through the higher horsepower capacity provided by Goodyear Hy-T V-belt construction. Vytacord tension members, treated with Goodyears 3-T process, provide strength and dimensional stability. Higher horsepower capacity is also provided through a tough Wingprene, fiberreinforced cushion, adding to belt strength. Hy-T Wedge is so strong that small sheave diameters arent a problem. Its often possible to achieve a required horsepower with fewer Hy-T Wedge belts than with standard V-belts reducing sheave size, sheave costs, and belt costs even more. Since less power is required to run the smaller, lighter drives, more power gets to the load. Therefore, you may be able to downsize drive motors and/or increase drive efficiency for even more savings.
Hy-T Wedge belts are available in a raw-edge construction with cogs for increased flexibility and heat dissipation or envelope construction for drives where pulsation, shock loads, high tension, and long centers are involved. Hy-T Wedge Cogged belts are high horsepower belt constructions that are identified with a 3VX and 5VX prefix and are available in lengths up to 200". The cogged construction provides the high flexibility required for short center distances. The cogs also provide a larger surface area to dissipate heat and prolong belt life. Improved material properties and advanced construction technology results in an average horsepower increase of 30% over standard Classical V-belt and wedge belts. Hy-T Wedge Envelope belts are identified with a 3V, 5V, or 8V prefix and are recommended for drives where pulsation, shock loads, high tension, and long centers are involved. It features a continuous V-section that is protected by a wide angle, synthetic fabric impregnated with high-quality Goodyear Wingprene rubber. This unique envelope achieves the high strength Hy-T Wedge belts need to withstand high loading forces. It also provides the torsional rigidity required in long center drives delivering the traction needed for accurate tracking and precision performance.
MATCHMAKER PERFORMANCE
Hy-T Wedge belts eliminate mismatch problems as each Matchmaker belt in a single length code is identical in size and performance to every other Hy-T Wedge belt in that size, no matter when or where it was produced.
51
V-BELT
0.38" 0.31"
0.62"
HY-T WEDGE
0.38" 0.31" 0.31" 0.53" 0.38" 0.62" 0.62" 0.53"
0.53"
1.00"
0.91"
5VX
Part Number 3VX560 3VX600 3VX630 3VX670 3VX710 3VX750 3VX800 Part Number 5VX740 5VX750 5VX780 5VX800 5VX810 5VX830 5VX840 5VX850 5VX860 5VX880 5VX900 Effective Length (in) 56.0 60.0 63.0 67.0 71.0 75.0 80.0 Effective Length (in) 74.0 75.0 78.0 80.0 81.0 83.0 84.0 85.0 86.0 88.0 90.0 Part Number 3VX850 3VX900 3VX950 3VX1000 3VX1060 3VX1120 3VX1180 Part Number 5VX930 5VX950 5VX960 5VX1000 5VX1030 5VX1060 5VX1080 5VX1120 5VX1150 5VX1180 5VX1230 Effective Length (in) 85.0 90.0 95.0 100.0 106.0 112.0 118.0 Effective Length (in) 93.0 95.0 96.0 100.0 103.0 106.0 109.0 112.0 115.0 119.0 123.0
8V
Effective Part Number Length (in) 3VX1250 125.0 3VX1320 132.0 3VX1400 140.0 3VX1500 150.0
Effective Length (in) 45.0 47.0 49.0 50.0 51.0 53.0 54.0 55.0 56.0 57.0 58.0
Part Number 5VX590 5VX600 5VX610 5VX630 5VX650 5VX660 5VX670 5VX680 5VX690 5VX710 5VX730
Effective Length (in) 59.0 60.0 61.0 63.0 65.0 66.0 67.0 68.0 69.0 71.0 73.0
Part Number 5VX1250 5VX1320 5VX1400 5VX1500 5VX1600 5VX1700 5VX1800 5VX1900 5VX2000
Effective Length (in) 125.0 132.0 140.0 150.0 160.0 170.0 180.0 190.0 200.0
52
V-BELT
NONCOGGED SIZES
Part Number 3V250 3V265 3V280 3V300 3V315 3V335 3V355 Part Number 5V500 5V560 5V630 5V670 5V710 5V750 5V800 Part Number 8V1000 8V1060 8V1120 8V1180 8V1250 8V1320 Effective Length (in) 25.0 26.5 28.0 30.0 31.5 33.5 35.5 Effective Length (in) 50.0 56.0 63.0 67.0 71.0 75.0 80.0 Effective Length (in) 100.0 106.0 112.0 118.0 125.0 132.0 Part Number 3V375 3V400 3V425 3V450 3V475 3V500 3V530 Part Number 5V850 5V900 5V950 5V1000 5V1060 5V1120 5V1180 Part Number 8V1400 8V1500 8V1600 8V1700 8V1800 8V1900 Effective Length (in) 37.5 40.0 42.5 45.0 47.5 50.0 53.0 Effective Length (in) 85.0 90.0 95.0 100.0 106.0 112.0 118.0 Effective Length (in) 140.0 150.0 160.0 170.0 180.0 190.0 Part Number 3V560 3V600 3V630 3V670 3V710 3V750 3V800 Part Number 5V1250 5V1320 5V1400 5V1500 5V1600 5V1700 5V1800 Part Number 8V2000 8V2120 8V2240 8V2360 8V2500 8V2650 Effective Length (in) 56.0 60.0 63.0 67.0 71.0 75.0 80.0 Effective Length (in) 125.0 132.0 140.0 150.0 160.0 170.0 180.0 Effective Length (in) 200.0 212.0 224.0 236.0 250.0 265.0 Part Number 3V850 3V900 3V950 3V1000 3V1060 3V1120 3V1180 Part Number 5V1900 5V2000 5V2120 5V2240 5V2360 5V2500 5V2650 Part Number 8V2800 8V3000 8V3150 8V3350 8V3550 8V3750 Effective Length (in) 85.0 90.0 95.0 100.0 106.0 112.0 118.0 Effective Length (in) 190.0 200.0 212.0 224.0 236.0 250.0 265.0 Effective Length (in) 280.0 300.0 315.0 335.0 355.0 375.0 Part Number 3V1250 3V1320 3V1400 Effective Length (in) 125.0 132.0 140.0
3V
Available Sizes DIAMETER (in) 2.20 2.35 2.50 2.65 2.80 3.00 3.15 3.35 JA JA JA JA JA JA, SH JA, SH JA, SH 3.65 4.12 4.50 4.75 5.00 5.30 5.60 6.00 SH SH SH, SDS SH, SDS, SK SH, SDS, SK SH, SDS, SK SH, SDS, SK SH, SDS, SK 6.50 6.90 8.00 10.60 14.00 19.00 25.00 33.50 SH, SDS, SK SH, SDS, SK SDS, SK, SF SDS, SK, SF, E SK, SF, E SK, SF, E SF, E, F SF, E, F
5V
Available Sizes 4.40 4.65 4.90 5.20 5.50 5.90 6.30 6.70 7.10 7.50 8.00 SH, SDS, SD SDS, SD SDS, SD SDS, SD SDS, SD SDS, SD, SK SK SK, SF SK, SF SK, SF SK, SF, E 8.50 9.00 9.25 9.75 10.30 10.90 11.30 11.80 12.50 13.20 14.20 SK, SF, E SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SK, SF, E, F SF, E, F, J SF, E, F, J SF, E, F, J 15.00 16.00 18.70 21.20 23.60 28.00 31.50 37.50 50.00 SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J E, F, J, M E, F, J, M F, J, M F, J, M F, J, M V-BELT DIAMETER (in)
8V
Available Sizes DIAMETER (in) 12.50 13.20 14.00 15.00 16.00 17.00 18.00 F, J, M F, J, M F, J, M F, J, M F, J, M F, J, M F, J, M 19.00 20.00 21.20 22.40 24.80 30.00 35.50 F, J, M, N J, M, N J, M, N J, M, N M, N M, N, P M, N, P 40.00 44.50 53.00 63.00 71.00 M, N, P M, N, P M, N, P, W P, W P, W
53
HY-T PLUS
(CLASSICAL)
APPLICATIONS Designed for operating at high speeds over small diameter pulleys and short center distances. Also for use in multiple V-belt drives where high shock load and heavy-duty loads are encountered. KEY FEATURES & BENEFITS Universal classical profile. High-strength Vytacord tensile members. Wingprene-impregnated Wingflex envelope. Goodyears Plioflex cushion and insulation. Dual branded (Classical and FHP part numbers). Oil, heat, ozone, and abrasion resistant. Matchmaker to eliminate mismatch. Static conductive.
Part No: B75 B .66" Top Width Classical Profile 75 Approximate 75" Inside Length
54
V-BELT
IMPROVED MATERIALS ARE THE KEY TO THE DURABILITY AND VERSATILITY OF HY-T PLUS
The vast improvements in all components of Hy-T Plus 0.66" 0.88" construction complement the quality of the Vytacord tensile member.
0.41" 0.53" Plioflex, Goodyears premium heat- and oil-resistant rubber compound, is used in both the cushion and insulation sections
1.25"
0.66"
0.75"
0.53"
0.41"
A SECTION
B SECTION
1.25"
C SECTION
1.25" 0.50"
D SECTION
0.50"
HY-T PLUS
Part Number Approx. Outside Length (in) Part Number Approx. Outside Length (in) Part Number
(CLASSICAL)
Part Number Approx. Outside Length (in) Part Number Approx. Outside Length (in)
A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38
(4L220) (4L230) (4L240) (4L250) (4L260) (4L270) (4L280) (4L290) (4L300) (4L310) (4L320) (4L330) (4L340) (4L350) (4L360) (4L370) (4L380) (4L390) (4L400)
22.0 23.0 24.0 25.0 26.0 27.0 28.0 29.0 30.0 31.0 32.0 33.0 34.0 35.0 36.0 37.0 38.0 39.0 40.0
Approx. Outside Length (in)
A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57
(4L410) (4L420) (4L430) (4L440) (4L450) (4L460) (4L470) (4L480) (4L490) (4L500) (4L510) (4L520) (4L530) (4L540) (4L550) (4L560) (4L570) (4L580) (4L590)
41.0 42.0 43.0 44.0 45.0 45.0 47.0 48.0 49.0 50.0 51.0 52.0 53.0 54.0 55.0 56.0 57.0 58.0 59.0
Approx. Outside Length (in)
A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76
(4L600) (4L610) (4L620) (4L630) (4L640) (4L650) (4L660) (4L670) (4L680) (4L690) (4L700) (4L710) (4L720) (4L730) (4L740) (4L750) (4L760) (4L770) (4L780)
60.0 61.0 62.0 63.0 64.0 65.0 66.0 67.0 68.0 69.0 70.0 71.0 72.0 73.0 74.0 75.0 76.0 77.0 78.0
Approx. Outside Length (in)
A77 A78 A79 A80 A81 A82 A83 A84 A85 A86 A87 A88 A89 A90 A91 A92 A93 A94 A95
(4L790) (4L800) (4L810) (4L820) (4L830) (4L840) (4L850) (4L860) (4L870) (4L880) (4L890) (4L900) (4L910) (4L920) (4L930) (4L940) (4L950) (4L960) (4L970)
79.0 80.0 81.0 82.0 83.0 84.0 85.0 86.0 87.0 88.0 89.0 90.0 91.0 92.0 93.0 94.0 95.0 96.0 97.0
Approx. Outside Length (in)
A96 A97 A98 A100 A103 A105 A110 A112 A120 A128 A133 A136 A144 A158 A173 A180
98.0 99.0 100.0 102.0 105.0 107.0 112.0 114.0 122.0 130.0 135.0 138.0 146.0 160.0 175.0 182.0
Part Number
Part Number
Part Number
Part Number
Part Number
B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44
(5L250) (5L260) (5L270) (5L280) (5L290) (5L300) (5L310) (5L320) (5L330) (5L340) (5L350) (5L360) (5L370) (5L380) (5L390) (5L400) (5L410) (5L420) (5L430) (5L440) (5L450) (5L460) (5L470)
25.0 26.0 27.0 28.0 29.0 30.0 31.0 32.0 33.0 34.0 35.0 36.0 37.0 38.0 39.0 40.0 41.0 42.0 43.0 44.0 45.0 46.0 47.0
B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67
(5L480) (5L490) (5L500) (5L510) (5L520) (5L530) (5L540) (5L550) (5L560) (5L570) (5L580) (5L590) (5L600) (5L610) (5L620) (5L630) (5L640) (5L650) (5L660) (5L670) (5L680) (5L690) (5L700)
48.0 49.0 50.0 51.0 52.0 53.0 54.0 55.0 56.0 57.0 58.0 59.0 60.0 61.0 62.0 63.0 64.0 65.0 66.0 67.0 68.0 69.0 70.0
B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 B83 B84 B85 B86 B87 B88 B89 B90
(5L710) (5L720) (5L730) (5L740) (5L750) (5L760) (5L770) (5L780) (5L790) (5L800) (5L810) (5L820) (5L830) (5L840) (5L850) (5L860) (5L870) (5L880) (5L890) (5L900) (5L910) (5L920) (5L930)
71.0 72.0 73.0 74.0 75.0 76.0 77.0 78.0 79.0 80.0 81.0 82.0 83.0 84.0 85.0 86.0 87.0 88.0 89.0 90.0 91.0 92.0 93.0
B91 B92 B93 B94 B95 B96 B97 B98 B99 B100 B101 B103 B105 B108 B111 B112 B116 B120 B124 B128 B133 B136 B140
(5L940) 94.0 (5L950) 95.0 (5L960) 96.0 (5L970) 97.0 (5L980) 98.0 (5L990) 99.0 (5L1000) 100.0 (5L1010) 101.0 (5L1020) 102.0 103.0 104.0 106.0 108.0 111.0 114.0 115.0 119.0 123.0 127.0 131.0 136.0 139.0 143.0
Approx. Outside Length (in)
B144 B148 B150 B154 B158 B162 B173 B180 B190 B195 B205 B210 B225 B240 B255 B270 B285 B300 B315
147.0 151.0 153.0 157.0 161.0 165.0 176.0 183.0 193.0 198.0 208.0 213.0 227.0 242.0 257.0 272.0 287.0 302.0 317.0
Part Number
Part Number
Part Number
Part Number
Part Number
55
V-BELT
TORQUE-FLEX
APPLICATIONS Designed for the tough, small sheave, high-tension drives. KEY FEATURES & BENEFITS Premium classical profile construction. 2530% higher power ratings than standard V-belts. Strong Vytacord (polyester) tensile members. Fiber-loaded Wingprene cushion compound. Cut-edge cogged construction on most sizes. Oil, heat, ozone, and abrasion resistant. Matchmaker to eliminate mismatch. Static conductive.
Part No: BX75 B .66" Top Width Classical Profile X Premium Cogged Construction 75 Approximate 75" Inside Length Cut-Edge, Molded Cog Construction Shown
ENERGY-SAVING EFFICIENCY
The same design and construction features which lead to high horsepower ratings for Goodyear Torque-Flex V-Belts also lead to improvements in energy efficiency of up to 4%, depending on sheave diameter.
94 NONCOGGED 92
90
88
56
TORQUE-FLEX
0.50" 0.31" 0.50" 0.50" 0.88" 0.88" 0.66" 0.66" 0.88" 0.66" 0.31" 0.31" 0.41" 0.41" 0.53" 0.53" 0.41" 0.53"
SIDE VIEW
Approx. Part 0.50" Outside Number Length (in) Outside 0.88" 0.66" Number Length (in) 23 AX39 41 24 0.41" AX40 0.53" 42 25 AX41 43 26 AX42 44 28 AX43 45 29 AX44 46 30 AX45 47 31 AX46 48 AX47 49 32 AX48 50 33 AX49 51 34 AX50 52 35 AX51 53 36 AX52 54 37 AX53 55 38 AX54 56 39 AX55 57 40 Approx. Part Outside Number Length (in) Part Approx.
AX
Approx. Part Outside Number Length (in)
BX
Approx. Part Outside Number Length (in)
CX
Approx. Part Outside Number Length (in)
BX28 BX32 BX34 BX35 BX36 BX38 BX40 BX41 BX42 BX43 BX44 BX45 BX46 BX47 BX48 BX49 BX50 BX51 BX52 BX53
31 35 37 38 39 41 43 44 45 46 47 48 49 50 51 52 53 54 55 56
BX54 BX55 BX56 BX57 BX58 BX59 BX60 BX61 BX62 BX63 BX64 BX65 BX66 BX67 BX68 BX69 BX70 BX71 BX72 BX73
57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76
BX74 BX75 BX76 BX77 BX78 BX79 BX80 BX81 BX82 BX83 BX84 BX85 BX86 BX87 BX88 BX89 BX90 BX91 BX92 BX93
77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
BX94 BX95 BX96 BX97 BX98 BX99 BX100 BX103 BX105 BX106 BX108 BX112 BX113 BX115 BX116 BX120 BX123 BX124 BX126 BX128
97 98 99 100 101 102 103 106 108 109 111 115 116 118 119 123 126 127 129 131
BX133 BX136 BX140 BX144 BX148 BX150 BX154 BX158 BX162 BX173 BX180 BX191 BX195 BX210 BX225 BX240 BX255 BX270 BX300
136 139 143 147 151 153 157 161 165 176 183 194 198 213 228 243 258 273 303
55 59 64 72 76 79 82
57
V-BELT
AX21 0.31" AX22 AX23 AX24 AX26 AX27 AX28 AX29 AX30 AX31 AX32 AX33 AX34 AX35 AX36 AX37 AX38
AX56 AX57 AX58 AX59 AX60 AX61 AX62 AX63 AX64 AX65 AX66 AX67 AX68 AX69 AX70 AX71 AX72
58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74
AX73 AX74 AX75 AX76 AX77 AX78 AX79 AX80 AX81 AX82 AX83 AX84 AX85 AX86 AX87 AX88 AX89
75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91
AX90 AX91 AX93 AX94 AX95 AX96 AX97 AX98 AX100 AX103 AX105 AX110 AX112
A/B
Available Sizes DIAMETER (in) 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 SH, SD SH, SD SH, SD SH, SD SH, SD SH, SD SDS, SD SDS, SD SDS, SD SDS, SD SDS, SD, SK 5.6 5.8 6.0 6.2 6.4 6.6 6.8 7.0 7.4 8.0 8.6 SDS, SD, SK SDS, SD, SK SDS, SD, SK, SF SDS, SD, SK, SF SDS, SD, SK, SF SDS, SD, SK, SF SDS, SD, SK, SF SDS, SK, SF SDS, SK, SF SDS, SK, SF SDS, SK, SF, E 9.4 11.0 12.4 13.6 15.4 16.0 18.4 20.0 25.0 30.0 38.0 SDS, SK, SF, E SDS, SK, SF, E SDS, SK, SF, E SDS, SK, SF, E SK, SF, E, F SK, SF, E, F SK, SF, F SK, SF, E, F SF, E, F SF, E, F SF, E, F, J
A/B
Available Sizes V-BELT 5.6 6.0 6.8
(LARGE BORE)
C
Available Sizes DIAMETER (in) 5.0 5.6 6.0 7.0 7.5 8.0 8.5 9.0 SD SD SF SF SF SF, E SF, E SF, E, F, J 9.5 10.0 10.5 11.0 12.0 13.0 14.0 16.0 SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J SF, E, F, J 18.0 20.0 24.0 27.0 30.0 36.0 44.0 50.0 SF, E, F, J SF, E, J, M SF, E, F, J, M F, J F, J, M F, J, M F, J, M F, J, M
D
Available Sizes DIAMETER (in) 12.0 13.0 13.5 14.0 14.5 15.0 F, J, M F, J, M F, J, M F, J, M F, J, M F, J, M 15.5 16.0 17.0 18.0 20.0 22.0 F, J, M F, J, M J, M J, M J, M J, M 24.0 27.0 33.0 40.0 48.0 58.0 J, M J, M J, M, N J, M, N J, M, N, P M, N, P
58
HEX
APPLICATIONS Used on drives having one or more reverse bends and usually where power must be transmitted to or from the belt in both the usual and reverse positions.
Part No: BB75 BB B Section Double Classical Profile 0.66" Center Width 75 Approximate 75" Inside Length
KEY FEATURES & BENEFITS Dual-sided classical profile. High-strength Vytacord tensile members. Wingprene-impregnated Wingflex envelope. Goodyears Plioflex cushion and insulation. Oil, heat, ozone and abrasion resistant. Static conductive.
59
HEX
AA
0.50" 0.41"
Part Number
Part Number
Part Number
AA51 0.66" 54.4 AA55 58.4 AA60 63.4 0.53" AA66 69.4 AA68 71.4
Approx. Part Outside Number 0.86" Length (in)
AA120 AA128
123.4 131.4
BB
0.96" 0.66" 0.53" 0.66"
Part Number
0.50"
.96"
0.86"
0.86"
0.50" 0.41"
BB45 BB51 0.86" BB54 BB55 BB60 BB68 BB71 BB72 BB73 BB74 BB75 BB81 BB83 BB85 BB90 0.66" BB92
0.53"
49.6 55.6 58.6 59.6 64.6 72.6 75.6 76.6 77.6 78.6 79.6 85.6 87.6 89.6 94.6 96.6
BB93 BB94 BB96 BB97 BB103 BB105 BB107 BB108 BB111 BB112 BB116 BB117 BB118 BB120 BB122 BB123
97.6 98.6 100.6 101.6 107.6 109.6 111.6 112.6 115.6 116.6 120.6 121.6 122.6 124.6 126.6 127.6
BB124 BB128 BB129 BB130 BB136 BB140 BB144 BB155 BB158 BB162 BB168 BB169 BB173 BB180 BB182 BB190
128.6 132.6 133.6 134.6 140.6 144.6 148.6 159.6 162.6 166.6 172.6 173.6 177.6 184.6 186.6 194.6
BB195 BB210 BB225 BB226 BB228 BB230 BB240 BB255 BB267 BB270 BB273 BB277 BB278 BB285 BB300
199.6 214.6 228.1 229.1 231.1 233.1 243.1 258.1 270.1 273.1 276.1 280.1 281.1 288.1 308.1
V-BELT
CC
0.96" 0.66"
Part Number
Part Number
Part Number
.50" 0.53"
0.66"
CC75 0.86" 81.4 CC81 87.4 CC85 91.4 CC90 96.4 0.86" CC96 102.4 CC105 111.4 CC112 118.4
CCP
0.86" 0.86"
.96"
60
INSTAPOWER
(FLEXTEN CLASSICAL)
APPLICATIONS Delivers high performance consistently in lawn and garden drives up to 20 horsepower. Also ideal for other power equipment where reverse bend idlers, misalignment, and quarter-turn drives cause ordinary belts to fail. KEY FEATURES & BENEFITS Flexten classical profile construction. High-strength Flexten tensile members. Fiber-loaded Wingprene cushion compound. Wingflex envelope construction. Triple part number branding (Instapower, Classical, and Fraction horsepower). Oil, heat, ozone and abrasion resistant. Static conductive.
Part No: 84310 84 Top Width in Eighths of an Inch 31 Length in Inches 0 Tenths of an Inch A29F - Equivalent Classical Size
0.50"
The fabric cover on Instapower belts is impregnated with 0.66" Goodyears exclusive Wingprene synthetic rubber compound
0.
"
0.31"
0.41"
0.41"
0.88" 0.22"
0.38"
0.88" 0.22"
0.3
83
3L SECTION
84
A SECTION 0.88" OR 0.88" 4L SECTION
85
0.22" 0.22"
B SECTION 0.38" OR 0.38" 5L SECTION
87
C SECTION
0.53" 0.53"
61
INSTAPOWER
Instapower 83160 83170 83180 83190 83200 83210
Instapower
(FLEXTEN CLASSICAL)
Instapower 83400 83410 83415 83420 83430 83440 Instapower 83450 83460 83470 83480 83490 83500
Flexten Classical Instapower
Instapower 83510
Instapower
Flexten Classical
Flexten Classical
84170 84180 84190 84200 84210 84220 84230 84240 84250 84255 84260 84270 84275 84280 84285 84290 84295
Instapower
A16F A17F A18F A19F A20F A21F A22F A23F A24F A25F A26F A27F
Flexten Classical
84300 84305 84310 84315 84320 84325 84330 84335 84340 84345 84350 84355 84360 84365 84370 84375 84380
Instapower
84385 84390 84400 84405 84410 84415 84420 84425 84430 84440 84450 84460 84470 84475 84480 84485 84490
Instapower
A37F A38F A39F A40F A41F A42F A43F A44F A45F A46F A47F
Flexten Classical
84500 84510 84520 84530 84540 84550 84560 84570 84580 84590 84600 84610 84620 84630 84640 84650 84660
A48F A49F A50F A51F A52F A53F A54F A55F A56F A57F A58F A59F A60F A61F A62F A63F A64F
84670 84680 84690 84700 84710 84720 84730 84740 84750 84760 84770 84780 84790 84800 84810 84820 84830
A65F A66F A67F A68F A69F A70F A71F A72F A73F A74F A75F A76F A77F A78F A79F A80F A81F
Flexten Classical
84840 84850 84860 84870 84880 84890 84900 84910 84920 84930 84940 84950 84960 84970 84980 84990 84999
Instapower
A82F A83F A84F A85F A86F A87F A88F A89F A90F A91F A92F A93F A94F A95F A96F A97F A98F
Flexten Classical
62
V-BELT
85240 85250 85260 85270 85280 85290 85300 85310 85320 85330 85335 85340 85350
Instapower
B21F B22F B23F B24F B25F B26F B27F B28F B29F B30F B31F B32F
Flexten Classical
85360 85370 85380 85390 85400 85410 85420 85430 85440 85450 85460 85470 85480
Instapower
B33F B34F B35F B36F B37F B38F B39F B40F B41F B42F B43F B44F B45F
Flexten Classical
85490 85500 85510 85520 85530 85540 85550 85560 85570 85580 85590 85600 85610
Instapower
B46F B47F B48F B49F B50F B51F B52F B53F B54F B55F B56F B57F B58F
Flexten Classical
85620 85630 85640 85650 85660 85670 85680 85690 85700 85710 85720 85730 85740
B59F B60F B61F B62F B63F B64F B65F B66F B67F B68F B69F B70F B71F
85750 85760 85770 85780 85790 58800 85810 85820 85830 85540 85850 85860 85870
B72F B73F B74F B75F B76F B77F B78F B79F B80F B81F B82F B83F B84F
Flexten Classical
85880 85890 85900 85910 85920 85930 85940 85950 85960 85970 85980 85990 85999
Instapower
B85F B86F B87F B88F B89F B90F B91F B92F B93F B94F B95F B96F B97F
Flexten Classical
C68F C75F
87850 87890
C81F C85F
87940 871000
C90F C96F
871040 871090
C100F C105F
871160 871240
C112F C120F
871320
C128F
FHP
APPLICATIONS For light-duty fractional horsepower motors. Molded cogs allow for use in applications where the belt is expected to perform around smaller sheave diameters.
Part No: 4L560 4L 0.50" Top Width 560 56.0" Nominal Outside Length Cut-Edge, Molded Cog Construction Shown
KEY FEATURES & BENEFITS Universal classical profile. Goodyears Plioflex cushion and insulation. Cut-edge, molded cogged construction. Oil, heat, ozone, and abrasion resistant. Static conductive.
Goodyear FHP V-belts efficiency begins at 93% when used with smaller sheaves and increases dramatically as the sheave diameter increases (Figure 1). Since more of the rated power of the drive is delivered, actual performance nearly matches design performance. In addition, the efficiency of Goodyear FHP V-belts offers you the opportunity to achieve full operating power requirements with a lower horsepower drive, reduced energy requirements, or both. These considerations can provide highly desirable economic advantages whether youre a drive manufacturer or a drive user. 98 COGGED 96 EFFICIENCY, % V-BELT
94 NONCOGGED 92
90
88
112
Figure 1 Efficiency comparison of cogged vs. noncogged FHP V-belts (4L section).
63
FHP
2L
0.25" 0.16"
Part Number Approx. Outside Length (in) Part Number Approx. Outside Length (in) Part Number Approx. Outside Length (in) Approx. Part Outside Number Length (in)
0.38"
12 14 15
16 18 19
Approx. Outside Length (in)
20 22 24
Approx. Outside Length (in)
30 31 32
3L
0.22" 0.31" 0.38" 0.50"
Part Number
Part Number
Part Number
5"
0"
V-BELT
3L120 3L130 3L140 3L150 3L160 0.38" 3L170 3L180 3L190 3L200 3L210 3L220 3L230 0.22" 3L240 3L250 3L260
12 13 0.66" 14 15 16 17 18 19 20 21 22 0.38" 23 24 25 26
Approx. Outside Length (in)
3L270 3L280 3L290 3L300 3L310 3L320 3L330 3L340 3L350 3L360 3L370 3L380 3L390 3L400 3L410
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Approx. Outside Length (in)
3L420 3L430 3L440 3L450 3L460 3L470 3L480 3L490 3L500 3L510 3L520 3L530 3L540 3L550 3L560
42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
Approx. Outside Length (in)
3L570 3L580 3L590 3L600 3L610 3L620 3L630 3L640 3L650 3L660 3L670 3L730 3L740 3L760
57 58 59 60 61 62 63 64 65 66 67 73 74 76
4L
0.50" 0.31"
Part Number
Part Number
Part Number
0.25" 0.22"
0.38"
4L150 4L160 4L170 0.38" 4L180 4L190 4L200 4L210 4L220 4L230 4L240 4L250 4L260
15 0.66" 16 17 18 19 20 21 22 23 24 25 26
4L270 4L280 4L290 4L300 4L310 4L320 4L330 4L340 4L350 4L360 4L370 4L380
27 28 29 30 31 32 33 34 35 36 37 38
Approx. Outside Length (in)
4L390 4L400 4L410 4L420 4L430 4L440 4L450 4L460 4L470 4L480 4L490 4L500
39 40 41 42 43 44 45 46 47 48 49 50
Approx. Outside Length (in)
4L510 4L520 4L530 4L540 4L550 4L560 4L570 4L580 4L590 4L600
51 52 53 54 55 56 57 58 59 60
5L
0.66" 0.38"
Part Number
Part Number
Part Number
0.50"
23 24 25 26 27 28 29 30 31
32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56
64
QT/FHP SHEAVES
QT/FHP SHEAVES
Available Sizes DESCRIPTION Single A Groove Two A Groove Single B Groove Two B Groove Single ABTS Single BBTS Two A GrooveBTS Two B GrooveBTS NOMENCLATURE AK 2AK BK 2BK AK BK 2AK 2BK SIZE RANGE (IN) 30-184 30-184 30-190 32-190 15-184 19-190 20-184 20-190 SIZE QT QT QT QT Various Various Various Various
VARIABLE SPEED
LIGHT -DUTY (FHP) ADJUSTABLE VP SHEAVES
Available Sizes DIAMETER IN INCHES 1VP25 1VP30 1VP34 1VP40 1VP44 1VP50 1VP56 1VP60 1VP62 1VP65 1VP68 1VP71 1VP75 2VP36 2VP42 2VP50 2VP56 2VP60 2VP62 2VP65 2VP68 2VP71 2VP75
65
V-BELT
NEOTHANE
APPLICATIONS Specialty belt for specific types of machines and equipment.
Part No: 5M 710 5M 3/6" Top Width 710 71.0" Nominal Outside Length
KEY FEATURES & BENEFITS Ribbed top for transverse rigidity, flexibility, and cool running conditions. Narrow top width for use on narrow, small diameter sheaves and exceptional flexibility on short centers. Cords are resistant to stretch or shrinkage, provide great strength and long flex life. Polyurethane compounding for firmer grip, greater strength, and high resistance to oil, heat, abrasion, ozone, and fatigue. Smooth machine sides for quiet running, vibration-free operation and uniform grip. Sixty-degree angle cross section for uniform support that keeps the load carrying cord in the same plane pulling together.
66
V-BELT
SMOOTH OPERATOR
Smaller sheave diameters, higher speed ratios, shorter center distances, and higher speeds in belt power transmission applications are possible. Elimination of double reduction drives, made possible by the higher speed ratios permitted, result in decreased space requirements for many applications. The precision characteristics of this belt give a smoothness of operation that reduces noise to a minimum in the appurtenances of a drive.
3M 0.125"
5M 0.188"
5M 0.188"
NEOTHANE
3M 3M
0.094" 0.094" 3M 0.125" 0.125" 5M 5M 0.188" 0.188"
0.125"
0.125"
5M
7M 7M
0.313" 0.219" 0.219"
7M 0.313"
11M 0.438"
11M 11M
0.438"
0.281"
0.281"
Part Number 0.313" 0.313" Part Number 0.438" 0.438" Eff. Length (in) Eff. Length (in) *3M243 9.57 *3M180 7.09 *3M250 9.84 *3M185 7.28 *3M258 10.16 *3M190 7.48 *3M265 10.43 *3M195 0.219" 0.219" 7.68 0.281" 0.281" *3M272 10.71 *3M200 7.87 *3M280 11.02 *3M206 8.11 *3M290 11.42 *3M212 8.35 *3M300 11.81 *3M218 8.58 *3M307 12.09 *3M224 8.82 *3M315 12.40 *3M230 9.06 *3M325 12.80 *3M236 9.29
11M
Part Number Eff. Length (in) *3M335 13.19 *3M345 13.58 *3M355 13.98 *3M365 14.37 *3M375 14.76 *3M387 15.24 *3M400 15.75 *3M412 16.22 *3M425 16.73 *3M437 17.20 *3M450 17.72
Part Number Eff. Length (in) *3M462 18.19 *3M475 18.70 *3M487 19.17 *3M500 19.69 *3M515 20.28 *3M530 20.87 *3M545 21.46 *3M560 22.05 *3M580 22.83 *3M600 23.62 *3M615 24.21
Part Number Eff. Length (in) *3M630 24.80 *3M650 25.59 *3M670 26.38 *3M690 27.17 *3M710 27.95 *3M730 28.74 *3M750 29.53
*Nonstock: Please check factory for availability. Note: Rubber equivalents for 5M, 7M, and 11M sizes are available in mandrel minimums.
67
V-BELT
VARIABLE SPEED
APPLICATIONS For use on variable speed sheave drives requiring exact speed control and maximum range of speed changes. Ideal for recreational equipment, agricultural applications, and machine tools.
Part No: 3226V585 32 32/16" Top Width 26 Angle of Sheave Groove V Variable Speed Profile - With Flexten Tensile Member 585 58.5" Pitch Length Molded-Edge, Molded Cog Construction Shown
KEY FEATURES & BENEFITS Durable variable speed profile. Super strong Flexten tensile members. Fiber-reinforced Wingprene compression section. Precision molded construction. High horsepower capacity. Three construction types available. Oil, heat, ozone, and abrasion resistant. Static conductive.
68
SPECIALTY
TRUE DIMENSIONAL STABILITY AND HIGHER HORSEPOWER CAPABILITY FOR LONG BELT LIFE
Goodyear Flexten tension carrying cords get their muscle from our 3-T process. Each tension member is tempered under Temperature, Tension, and Time to its maximum strength and resilience. This gives Goodyear Variable Speed belts the dimensional stability they need to carry more horsepower and to experience less stretch over the life of the belt. In short, Goodyear Variable Speed belts provide you with longer life on the toughest drives.
VARIABLE SPEED
Metric and asymmetric sizes available in minimum quantities. Note: Envelope construction available in certain sizes. Minimum quantity required.
69
SPECIALTY
FLAT BELTING
(TRULY ENDLESS)
APPLICATIONS Handles a wide range of horsepower and speeds in both industrial and agricultural drives.
Harvesting Equipment Textiles and Forestry Hay Equipment Industrial Equipment Direct Gear Drive Replacement
Soil Handling Food Processing Chain Replacement Health and Fitness Material Handling
KEY FEATURES & BENEFITS Smooth, quiet operation and long belt life. Uniform belt surface with no splicing. High-tensile strength. High coefficient of friction. Lightweight. No lubrication necessary. Transverse rigidity. Goodyear manufactures a complete line of flat belting from Truly Endless Compass and Multiple Ply belts to Regulator Power Strap flat belts for the health and fitness industry.
70
FLAT BELTING
COMPASS CORD BELT
Compass Number L M C H Type of Service Light Medium Heavy Extra Heavy Construction Endless Endless Endless Endless
(TRULY ENDLESS)
Width Limits 1"36" 2"36" 4"36" 4"36" Length Limits 20.5"120" 20.5"135" 49"135" 49"135"
*Special sizes available on request. Contact your local GTM or Goodyear Distributor.
*Special sizes available on request. Contact your local GTM or Goodyear Distributor.
.10"
1% Stretch at 500#
.10"
1% Stretch at 625#
.10"
1% Stretch at 850#
*Special sizes available on request. Contact your local GTM or Goodyear Distributor.
71
BOWLING MACHINE
AMF Part Number 000-022-099 000-025-731 000-026-753 000-027-710 000-028-864 000-028-865 000-029-600 030-003-912 030-005-197 Brunswick Part Number 10-635112 10-635126 10-635303 10-635304 10-635308 10-635309 10-635314 12-150113 Goodyear Part Number a112 8350 CARPET 2L360 8690 8695 8640 A133 B128 Goodyear Part Number 8555 8505 A90 A64 4L335 A80 4L350 8620 AMF Part Number 030-005-453 030-008-671 030-008-792 070-001-424 070-002-005 82-70-2013 000-029-433 057-001-003 146-004-772 Brunswick Part Number 12-300082-3 12-400034-2 12-400034-3 12-400034-4 12-400034-5 12-400223 12-400227 12-400314 Goodyear Part Number 8520 A133 A133 2L360 B190 8685 3L360 4L410 5M1850 Goodyear Part Number 8625 A75 A105 A120 B195 8615 B205 AX112 AMF Part Number 146-004-775 208-111-174 070-011-064 070-011-147 070-011-148 234-001-147 702-504-012 702-504-013 Goodyear Part Number 5M925 3L450 3L450 3L380 3L400 8595 A68 A34
COTTON CLEANER
SPECIALTY
Part No: 64 CCB 64 64" Pitch Length CCB 1" Pitch
APPLICATIONS Synchronous belts specially designed for driving the cylinders on Cotton Gin Incline cleaner machines. KEY FEATURES & BENEFITS Steel tensile cords. Long service life in harsh environments.
No. of Teeth 61 63 64 65
72
FIN FAN
APPLICATIONS Specific application power transmission synchronous belts used primarily in the chemical, petroleum, and refining industries. KEY FEATURES & BENEFITS Special Fin Fan construction. Universal tooth profile drops into existing HTD sprockets. Quiet tooth engagement. High-grade Wingprene compound. Higher horsepower Plus construction. Fiberglass tension cords for excellent resistance to shrinkage/elongation. Oil, heat, ozone, and abrasion resistance. Low-maintenance/high-efficiency rating.
Part No: 3150 14M 55\FFAN 3150 3150mm Pitch Length 14 14mm Pitch 55 55mm Wide \FFAN Special Fin Fan Construction
Part Number 3150 14M 55\FFAN 3150 14M 85\FFAN 3360 14M 55\FFAN 3360 14M 85\FFAN
Part Number 3500 14M 55\FFAN 3500 14M 85\FFAN 3850 14M 55\FFAN 3850 14M 85\FFAN
APPLICATIONS For snowmobiles, golf carts, ATV vehicles, and various other recreational vehicles requiring variable speed belts. KEY FEATURES & BENEFITS Built for speed at high horsepower. Heavy gauge Flexten cord thats pound-for-pound five times stronger than steel. Special tire cord supports the Flexten cord for extra load capacity. Flexten fiber cushion increases heat resistance. Fabric cover cogs allow for dissipation of heat buildup and long belt life.
* For an application guide and the full range of sizes available, ask your distributor for the Goodyear SV catalog. Catalog Description Sports Vehicle Application Guide Part Number 20035750
73
SPECIALTY
Part No: 4061025 4 K Section Poly-V 06 6 Ribs 1025 102 5/10" Length
GATORBACK V-BELT
APPLICATIONS For passenger cars and light- and heavy-duty trucks. KEY FEATURES & BENEFITS High-strength Vytacord tension members resist shockload failure. Low-stretch properties assure uniform performance over the long life of the belt. Fiber-reinforced Wingprene helical cogs offer greater flexibility which reduces cracking and fatigue in the cushion member. Tension fabric impregnated with Wingprene oilresistant rubber reduces surface fatigue and resists cracking. Rubber edges maintain positive, no-slip contact with pulley grooves for reliable energy transfer.
74
AUTOMOTIVE
Part No: 42001
TIMING BELT
APPLICATIONS Goodyear Timing belts are engineered to deliver precise timing over a long service life in demanding automotive cam applications. KEY FEATURES & BENEFITS Precision-molded teeth made of Wingprene provide high strength, shear resistance, and environmental resistance to assure long, dependable life. Specially woven and chemically treated fabric is impregnated with Wingprene to reduce pulley friction and provide outstanding resistance to abrasion, oil, and ozone. Special fiberglass tension members are dimensionally stable and high in strength starting out precise and dependable and staying that way. Durable Wingprene backing protects the loadcarrying cords from oil, abrasion, and ozone. It also keeps the cords in place so they pull together smoothly and evenly. Goodyear Timing belts are molded, not cut, to achieve precision tolerances for pitch, width, and length for a perfect mesh with pulley grooves.
Part No: 40138 40 Automotive Timing Belt 138 Industry Standard Description
Note: For an application guide and available sizes of Goodyear Gatorback V-belts, Poly-V belts, Truck Refrigeration belts, Special Truck belts, and Timing belts, ask your distributor for the following catalogs: Catalog Description Car & Light Truck Application Guide (Current to 1994) Car & Light Truck Application Guide (1993 & Prior) Part Number 20035740 20049146 Catalog Description Medium to Heavy Duty Truck Application Guide (Current to 1990) Medium to Heavy Duty Truck Application Guide (1989 & Prior) Part Number 20049138 20108695
75
UP TO 210"
Add 2.1" to Part Number Ex: A20 = 22.1" Add 2.9" to Part Number Ex: B100 = 102.9" Add 4.2" to Part Number Ex: C100 = 104.2" Add 5.2" to Part Number Ex: D180 = 105.2" Add 7.0" to Part Number Ex: E180 = 187.0"
LENGTHS
Belt Number indicates nominal Outside Length Example: 3V x 475 = 47.5"
FHP SECTION
2L 3L 4L 5L
LENGTHS
Belt Number indicates nominal Outside Length
POSITIVE DRIVE
PITCH WIDTH LENGTH Distance from center of one tooth to center of next MXL = .080" XL = .200" L = .375" H = .500" XH = .875" XXH = 1.250"
Last digits of belt number are the width in inches and tenths Example: 240XL025 = 1/4" width
First digits of belt number are the pitch length in inches and tenths Example: 240XL025 = 24.0" Pitch length
POLY-V SECTION
J L M
THICKNESS
.16 .38 .66
LENGTH
First digits are pitch length in inches and tenths Example: 180J4 = 18.0" J = Poly-V cross section 4 = number of ribs
VARIABLE SPEED
TOP WIDTH ANGLE LENGTH First two digits of belt number indicate belt top width in sixteenths of an inch Example: 3226V585 = 32/16" or 2" top width Second two digits of belt number indicate the pulley angle Example: 3226V585 fits a 26-angle pulley
GENERAL INFORMATION
Last digits of belt number are the pitch length Example: 3226V585 = 58.5" pitch length
76
BUSHINGS
Sure-Grip Quick Detachable bushings are easy to install and remove. They are split through flange and taper to provide a true clamp on the shaft that is the equivalent of a shrink fit. All sizes except JA and QT have a setscrew over the key to help maintain the bushings position on the shaft until the cap screws are securely tightened. Sure-Grip bushings have a very gradual taper (3/4-inch taper per ft. on the diameter) which is about half the inclined angle of many other bushings. The result is the Sure-Grip securely clamps the shaft, with twice the force of those competitive bushings, to provide extreme holding power. Versatile Sure-Grip bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing. Their interchange ability extends through sheaves, pulleys, timing pulleys, sprockets, flexible and rigid couplings, madeto-order items by Goodyear, and to product lines of several other mechanical power transmission manufacturers. Sure-Grip bushings are manufactured with the drilled and tapped holes located at a precise distance from the keyseat; thus, a wide mating part having a bushing in each end can be mounted on a common shaft with the two keyways in line. This feature not only facilitates installation but also permits both bushings to carry an equal share of the load.
6-hole drilling (most sizes) makes installation and removal quick and easy. Precise taper (3/4 in. per ft. on diameter) provides proper wedging action. Saw cut through flange and taper (and sometimes cut down into keyway also) to provide a true clamp fit. Cap screws used to secure bushings to sheave and to remove bushing from sheave.
QT JA SH SDS SD SK SF E
F J M N P SKL SFL EL
SURE-GRIP IDLER BUSHINGS AND REPLACEMENT BEARINGS SH-BB SF-BB SD-BB E-BB SK-BB
METRIC SURE-GRIP BUSHINGS QTMX SKMX JAMX SFMX SHMX EMX SDSMX FMX SDMX
GENERAL
77
GENERAL INFORMATION
78
TECHNICAL INFORMATION
SAFETY REMINDER SPROCKET INSTALLATION
Follow all safety policies and requirements of federal, state and local authorities, as well as the regulation of the employer, when working on power equipment. Always lock out the power source to the machinery before performing any work.
PREPARATION
OBJECTIVE: Verify that all necessary tools and parts are available and ready for installation. 1. Eagle Pd belts and sprockets from Goodyear are identied with a unique Color Spectrum System. The seven colors used for identication are: Yellow, White, Purple, Blue, Green, Orange, and Red. Each color represents a different size so that Blue belts are made to operate with Blue sprockets. Make sure the same color belt and sprockets have been obtained. When installing Whitehawk Pd and Blackhawk Pd, it is also important that the correct sprocket width is used. 2. The following tools are recommended for proper belt and sprocket installation. A straight edge A tape measure Socket and open-end wrenches A le and sandpaper A torque wrench A clean cloth A belt tension gauge Deection force values for tensioning the belt 3. Make sure the components are ready for installation. Clean all shafts, removing any nicks or burrs. Clean all mating surfaces of the sprocket, bushing, and shaft. No lubrication or anti-sieze solution should be used on any of these surfaces, including threaded holes. Use of lubrication can create higher torque, which will cause premature failure. 4. Make sure the shafts are true and parallel by accurately measuring the distance between the shafts at three points along the shaft. The distance between the shafts should be the same at all three points as shown. Also make sure the shafts are rigidly mounted. Shafts should not deect when the belt is tensioned.
GENERAL
79
TECHNICAL INFORMATION
5. With capscrews to the outside, place the sprocket and bushing assembly on the shaft, positioning the assembly as close as possible to the motor bearing. 6. Repeat Steps 25 for the other sprocket. 7. Check that the teeth of both sprockets are pointing in the same direction. 8. Snug the capscrews so that the sprocket/bushing assembly can still move on the shaft. 9. Align the sprockets using a straightedge. Check for contact in four places as shown. Do not use bearings or drive shafts as reference points for sprocket alignment. 10. Using a torque wrench, tighten the capscrews to the torque values listed below. If there is not a gap of 1/8" to 1/4" between the bushing ange and the sprocket hub then disassemble the parts and determine the reason for the faulty assembly. 11. The sprocket will draw onto the bushing during tightening. Always recheck alignment after tightening the capscrews. If alignment has changed, return to Step 8. 12. Tighten the setscrews over the keyway to the torque values listed in the table to the right. 13. If the sprockets are straight bore, use the above alignment procedure and then tighten the setscrews to the correct torque for the setscrew size listed in the Torque Specications table. QD bushings can be installed with the capscrews on either side, excluding H, M, and N sizes. Drives with opposing shafts require one of the sprockets be mounted with the capscrews on the ange side and one with the capscrews on the hub side.
BUSHING
TORQUE SPECIFICATIONS
CAPSCREW TORQUE SETSCREW SETSCREW TORQUE SIZE
(in-lb) 95 108 108 180 360 720 900 1620 2700 3600
(in) 1/4 1/4 1/4 5/16 3/8 3/8 3/8 3/8 1/2
H SH SDS SK SF E F J M N
GENERAL INFORMATION
80
TECHNICAL INFORMATION
BELT INSTALLATION AND TENSIONING
OBJECTIVE: Goodyear Pd timing belts must be installed and tensioned properly to ensure optimum performance. Sprocket alignment must be preserved while tensioning the drive. Before beginning, inspect the belt for damage and verify that the sprockets are properly mounted. Refer to sprocket and bushing manufacturer installation procedure. Belts should never be crimped or bent to a diameter less than the minimum sprocket diameter, approximately 2 inches for 8mm belts and 5 inches for 14mm belts. 1. Shorten the center distance or release the tensioning idler to install the belt. Do not pry the belt onto the sprocket. 2. Place the belt on each sprocket and ensure proper engagement between the sprocket and belt teeth. 3. Lengthen the center distance or adjust the tensioning idler to remove any belt slack. 4. Using a tape measure, measure the span length of the drive. Refer to dimension P in the diagram below. The span length can be calculated using the below formula. 5. Place a straightedge or reference line across the top of the belt. 6. First determine the proper deection force to tension the belt. Deection forces are given in the following tables. Deection forces are also given on the output of the Maximizer computer drive analysis. a) If using a tension gauge, the deection scale is calibrated in inches of span length. Check the force required to deect the belt the proper amount. There is an O-ring to help record the force. If the measured force is less than the required deection force, lengthen the center distance. If the measured force is greater than the required deection force, shorten the center distance. See chart on page 82 for deection values and tension gauges available. b) If using other means to apply force to the belt, adjust the center distance so that the belt is deected 164 per inch of span length when the proper force is applied. See chart on page 82 regarding RSM2000 Belt Tension Meter which calculates belt tension by measuring span vibrations. 7. After the belt is properly tensioned, lock down the center distance adjustments and recheck the sprocket alignment. Recheck the belt tension, alignment, and capscrew torque after eight hours of operation to ensure the drive has not shifted.
P. SPAN LENGTH
Q. DEFLECTION (IN)
F = Deection Force q = Deection, 164" per inch of span length C = Center Distance D = Large Sprocket Pitch Diameter d = Small Sprocket Pitch Diameter P = Span Length
GENERAL
81
TECHNICAL INFORMATION
DEFLECTION FORCES FOR BELT TENSIONING (LBS)
Use with Deection Gauges
Belt Type Yellow White Purple Blue Green Orange Red 8MBH 12 8MBH 22 8MBH 35 8MBH 60 14MBH 20 14MBH 42 14MBH 65 14MBH 90 14MBH 120 8MWH 20 8MWH 30 8MWH 50 8MWH 85 14MWH 40 14MWH 55 14MWH 85 14MWH115 14MWH170 0-100 RPM New Belt Used Belt 15 11 30 21 60 43 54 38 80 57 107 76 161 115 12 23 36 62 36 76 117 162 217 15 23 39 69 47 70 116 162 249 9 17 26 45 26 55 85 118 157 11 17 29 50 34 51 84 118 181 101-1000 RPM New Belt Used Belt 12 8 24 17 47 34 44 31 66 47 88 63 131 94 9 16 26 45 27 57 89 123 164 13 20 35 61 38 56 93 130 201 7 12 19 33 20 42 65 90 119 10 15 26 45 28 41 68 95 146 1000-up RPM New Belt Used Belt 9 7 19 13 38 27 38 27 57 41 76 55 115 82 7 13 21 36 23 49 76 105 139 12 19 32 56 32 48 79 110 171 5 10 16 27 17 36 55 77 102 9 14 24 51 24 35 58 80 125
PART NUMBER
Eagle Pd Tension Tester (PN 20039446) or Small Tension Tester (PN 20044882)
APPLICATION
Eagle Pd Yellow and White 8mm WhiteHawk Pd 20 & 30mm wide 8mm BlackHawk Pd 12 & 22mm wide
EAGLE PD
PART NUMBER
Eagle Pd Tension Tester (PN 20039447) or Small Tension Tester (PN 20083773)
BLACKHAWK
APPLICATION
Eagle Pd Purple, Blue, Green, Orange & Red 8mm WhiteHawk Pd 50 & 85mm wide 14mm WhiteHawk Pd 40, 55, 85, 115 & 170mm wide 8mm BlackHawk Pd 35 & 60mm wide 14mm WhiteHawk Pd 20, 42, 65, 90 & 120mm wide
WHITEHAWK
PART NUMBER
RSM2000 Tension Meter The RSM2000 belt tensioning device can be used to tension Goodyear WhiteHawk Pd and BlackHawk Pd timing belts. For the meter to read belt strand tension in Newtons, the only inputs required are specic belt mass (in g/meter) and span length (in mm). The best strand tension in Newtons is provided in the adjacent table along with the specic mass of the belt (in g/meter). The microcontroller-based RSM2000 measures belt vibrating frequency with a highly sensitive sensor and provides an easy and accurate means of tensioning the belt to the correct installation tension. 1) The table values are typically larger than necessary to cover the broad RPM range. 2) For drives where hub loads are critical and high speed drives or other drives with special circumstances, the table values (deection force, installation tension) should be calculated. 3) Consult the Web site, accubelt.com, for detailed information on using the frequency-based tension gauges. 4) Goodyear offers three different tension gauges for properly tensioning Eagle Pd, WhiteHawk Pd or BlackHawk Pd belts. See your Goodyear sales representative or your local Goodyear Power Transmission distributor for more information on the tension gauges listed on this page.
82
WHITEHAWK
BLACKHAWK
EAGLE PD
GENERAL INFORMATION
TECHNICAL INFORMATION
DRIVE ALIGNMENT
Synchronous belts are very sensitive to misalignment. Tension carrying members are generally twisted, multiple strands of berglass cord. Fiberglass has a high tensile strength and resistance to elongation, resulting in a very stable belt product. Any misalignment will lead to inconsistent belt wear, uneven load distribution, and premature tensile failure. In general, synchronous drives should not be used where misalignment is a problem. Misalignment should be limited to 13 degree or 116 inch per foot of center distance. Misalignment can be dened in one of two ways. First, if two sprockets are not located equally on shafts, sprockets are then misaligned, as in Figure A. Second, shafts may not be parallel, resulting in misalignment, as in Figure B.
FIGURE A
FIGURE B
MISALIGNED
Any degree of misalignment will reduce belt life and cause edge wear. Therefore, a straightedge should be used to check proper alignment verifying that sprockets and shafts are parallel, as in Figure C.
FIGURE C
Correct Alignment A straightedge should touch the sprocket at the four points indicated. Both front and back alignments should be checked.
ALIGNED
Misalignment, at times, may cause tracking problems. Although some tracking is normal and will not affect belt performance, it may be caused by poorly aligned sprockets. Flanges may control a tracking problem. Considering a twosprocket drive, belt contact on a single ange is acceptable. Belt contact with the opposite anges of two sprockets should be avoided.
GENERAL
Misalignment can also be attributed to the improper installation of a bushing or loose drive framework. Refer to sprocket manufacture guidelines for proper bushing installation. Secure motor and framework to eliminate vibration on center-to-center uctuations.
83
TECHNICAL INFORMATION
MANUFACTURING TOLERANCES
FOR WHITEHAWK PD, BLACKHAWK PD, HI-PERFORMANCE PD PLUS WIDTH TOLERANCES Belt Width (mm) Up to 38 Over 38 to 51 Over 51 to 76 Over 76 to 102 Over 102 Width Tolerances on Belt Lengths 0 to 838mm +0.8 0.8 +0.8 1.2 +1.2 1.6 +1.6 1.6 +2.4 2.4 Width Tolerances on Belt Lengths Over 838 to 1676mm +0.8 1.2 +1.2 1.2 +1.6 1.6 +1.6 2.0 +2.4 2.8 Width Tolerances on Belt Lengths Over 1676mm +0.8 1.2 +1.2 1.6 +1.6 2.0 +2.0 2.0 +2.4 3.2
BELT THICKNESS AND OVERALL GUAGE TOLERANCES (MM) Belt Pitch 8mm 14mm Nominal Web Thickness 2.0 3.4 Nominal Overall Gauge 5.5 10.0 Overall Gauge Tolerance 0.40 0.50 Overall Gauge Variation Single Belt 0.40 0.50
LENGTH TOLERANCES Belt Length (mm) Over 254 to 381 Over 381 to 508 Over 508 to 762 Over 762 to 1016 Over 1016 to 1270 Over 1270 to 1524 Over 1524 to 1778 Over 1778 to 2032 Over 2032 to 2286 Over 2286 to 2540 Over 2540 to 2794 Over 2794 to 3048 Over 3048 to 3302 *Std. Length Tolerances (Center-to-Center) 0.23 0.25 0.30 0.33 0.38 0.41 0.43 0.46 0.48 0.51 0.53 0.56 0.58 Belt Length (mm) Over 3302 to 3556 Over 3556 to 3810 Over 3810 to 4064 Over 4064 to 4318 Over 4318 to 4572 Over 4572 to 4826 Over 4826 to 5080 Over 5080 to 5334 Over 5534 to 5588 Over 5588 to 5842 Over 5842 to 6096 Over 6096 to 6350 Over 6350 to 6604 Over 6604 to 6860 *Std. Length Tolerances (Center-to-Center) 0.61 0.64 0.66 0.69 0.71 0.74 0.76 0.79 0.81 0.84 0.86 0.89 0.91 0.94
GENERAL INFORMATION
*NOTE: The length tolerances given for Positive Drive belts refer to the center-to-center tolerance between belts when checked on a standard measuring xture. The actual pitch length tolerance is twice the value shown. If a special tension member is used, consult the factory for proper length tolerances.
84
TECHNICAL INFORMATION
CORRECTIVE ACTION
Check Belt/Sprocket Compatibility Follow Proper Handling Procedure Reinstall, Replace, Repair Flange Eliminate or Control Condition Check Horsepower Rating Change Sprocket Material
Check Alignment
Replace Sprocket
GENERAL
TYPE OF FAILURE CAUSE OF FAILURE Excessive Edge Wear Misalignment or Improper Tracking Bent or Rough Flange Damage Due to Handling Belt Too Wide Low Belt Tension Belt Hitting Obstruction Excessive Tooth Wear Excessive Load Belt Overtensioned/Undertensioned Rough or Damaged Sprocket Partial Belt Engagement Bushing/Sprocket Assembly Misalignment Incorrect Match of Belt and Sprocket Worn Sprocket Sprocket Out of Tolerance Soft Sprocket Material Debris in Sprocket Apparent Belt Stretch Change in Center Distance Center Distance Fluctuates Weak Drive Structure or Mounts Worn Sprocket Debris in Sprocket Excessive Load Sprocket Diameter below Minimum Recommendation Excessive Low or High Temperature (30F to +170F) Exposure to Oil, Solvents, Harsh Chemicals Cracks in Backing Excessive Low or High Temperature Sprocket Diameter below Minimum Recommendation Backside Idler Exposure to Oil, Solvents, Harsh Chemicals
Redesign Drive
Adjust Tension
85
TECHNICAL INFORMATION
CORRECTIVE ACTION
Check Belt/Sprocket Compatibility Follow Proper Handling Procedure Reinstall, Replace, Repair Flange Eliminate or Control Condition Check Horsepower Rating Change Sprocket Material
Check Alignment
Replace Sprocket
TYPE OF FAILURE CAUSE OF FAILURE Tooth Shear Excessive Load/Shock Load Sprocket Diameter Below Minimum Recommendation Less Than 6 Teeth in Mesh Excessive Sprocket Runout Worn Sprocket Backside Idler Incorrect Match of Belt and Sprocket Tensile Failure Misalignment Belt Overtensioned/Undertensioned Excessive Load/Shock Load Sprocket Diameter Below Minimum Recommendation Damage Due to Handling Debris in Sprocket or Drive Excessive Sprocket Runout Excessive Drive Noise Misalignment Belt Overtensioned/Undertensioned Excessive Load Sprocket Diameter Below Minimum Recommendation Backside Idler Worn Sprocket Damaged Flange Excessive Belt Speed Incorrect Match of Belt and Sprocket Unmounting of Flange Misalignment Flange Incorrectly Mounted Belt Tracking Misalignment Center Distance Exceeds 8X Small Sprocket Diameter Excessive Pulley Wear Soft Sprocket Material Excessive Load Misalignment Debris in Sprocket Belt Overtensioned/Undertensioned Incorrect Match of Belt and Sprocket Excessive Drive Bushing/Sprocket Assembly Vibration Incorrect Match of Belt and Sprocket Belt Overtensioned/Undertensioned
86
Redesign Drive
Adjust Tension
GENERAL INFORMATION
HY-T Wedge Belts Envelope 3V 5V 8V Up to HY-T Wedge Belts Cut-Edge 120" 3VX 5VX Torque Team Belting 3VX 5VX 8V AX BX CX DX Cut-Edge 25" 118" 90 54 --66 50 36 29 3V 5V 8V A B C D 98 63
116" 123" 90 50 30 69 50 35 22
Envelope 124" 301" 300" & Up 175 100 64 135 95 64 36 --50 32 --50 32 24 Variable Speed Belts Hex Belts AA BB CC DD Cut-Edge Automotive Belts
Any Length 38" Wide Mandrel** 0 123" 67 49 33 --124" 300" 108 94 60 50 Over 300" --47 30 24
Top 12"116" Width Length 13/32 15/32 17/31 22/32 32/32 28/32 32/32 98 87 73 60 54 45 39
3L 106 5L *2Ls unavailable in Envelope Construction. 12"116" Length 2L 3L 4L 5L 152 98 79 63 Under 116" 73 57 42 ---
62
FHP Cut-Edge
240"300" 300" & Over 60 30 12"118" Length 5MR 7MR 11MR 194 121 83
Neothane Belts
Torque-Flex Belts AX BX CX DX
116" 123" 73 51 37 24
Poly-V belt (cut-edge only) J Section L Section M Section K Section 10"-120"= 400 ribs 25"-120" = 200 ribs 50"-118" = 100 ribs 12"-118" = 265 ribs
* Nonstock Belts: Orders for nonstock or made-to-order belts are available in multiple mandrel quantities. Please check factory for availability of equipment and/or availability for the desired construction. ** Inches indicate the total top width mandrel yield (e.g., divide belt top width into yield for total number of belts per mandrel).
GENERAL
87
BELT STORAGE
GENERAL GUIDELINES
The storage of power transmission belts is of interest to users and distributors as well as manufacturers. Under favorable storage conditions, good quality belts retain their initial serviceability and dimensions. Conversely, unfavorable conditions can adversely affect performance and cause dimensional change. Good storage facilities and practices will allow the user to achieve the most value from belt products. Power transmission belts should be stored in a cool and dry environment with no direct sunlight. When stacked on shelves, the stacks should be small enough to avoid excess weight on the bottom belts which may cause distortion. When stored in containers, the container size and contents should be sufficiently limited to avoid distortion, particularly to those belts at the bottom of the container.
METHODS OF STORAGE
1. V-BELTS A common method of storing belts is to hang them on pegs or pin racks. Very long belts stored this way should use sufficiently large pins or crescent-shaped saddles to prevent their weight from causing distortion. Long V-belts may be coiled in loops for easy distortion-free storage. The following is a guide to the maximum number of coils for extended storage time.
Belt Cross Section 3L, 4L, A, AX, AA 5L, B, BX, 3V 9R, 13R, 13C, 13CX, 13D 16R, 16C, 16CX, 9N BB, C, CX 5V 16D, 22C, 22CX 15N
Belt Length (in) Under 60 60 up to 120 120 up to 180 180 and over Under 75 75 up to 144 144 up to 240 240 and over Under 120 120 up to 240 240 up to 330 330 up to 420 420 and over Under 180 80 up to 270 270 up to 390 390 up to 480 480 and over
Belt Length (mm) Under 1,500 1,500 up to 3,000 3,000 up to 4,600 4,600 and over Under 1,900 1,900 up to 3,700 3,700 up to 6,000 6,000 and over Under 3,000 3,000 up to 6,100 6,100 up to 8,400 8,400 up to 10,600 10,600 and over Under 4,600 4,600 up to 6,900 6,900 up to 9,900 9,900 up to 12,200 12,200 and over
No. of *Coils 0 1 2 3 0 1 2 3 0 1 2 3 4 0 1 2 3 4
No. of Loops 1 3 5 7 1 3 5 7 1 3 5 7 9 1 3 5 7 9
8V (25N)
*One coil results in three loops, two coils result in five loops, etc.
88
BELT STORAGE
METHODS OF STORAGE
CONT.
2. JOINED V-BELTS, SYNCHRONOUS BELTS, V-RIBBED BELTS Like V-belts, these belts may be stored on pins or saddles with precautions taken to avoid distortion. However, belts of these types, up to approximately 120 inches (3000 mm), are normally shipped in nested configuration and it is recommended that the belts be stored in this manner as well. Nests are formed by laying a belt on its side on a flat surface and placing as many belts inside the first belt as possible without undue force. When the nests are tight and are stacked with each rotated 180 from the one below, they may be stacked without damage. Belts of these types over approximately 120 inches (3000mm), may be rolled up and tied for shipment. These rolls may be stacked for easy storage. Care should be taken to avoid small radii, which could damage the belts.
3. VARIABLE SPEED BELTS Variable speed belts are more sensitive to distortion than most other belts and it is not recommended that these belts be hung from pins or racks. They should be stored on shelves. A common method for packaging for shipment is the use of a sleeve slipped over the belt. Variable speed belts should be stored in these sleeves and may conveniently be stacked on shelves with the aid of the sleeves.
EFFECTS OF STORAGE
The quality of belts has not been found to change significantly within eight years of proper storage at temperatures less than 85F (30C) and relative humidity below 70 percent. Also there must be no exposure to direct sunlight. If the storage temperature is increased beyond 85F (30C), then the storage limit for normal service expectancy should be reduced. From a base of eight years at 85F (30C), the storage limit should be reduced by one-half for each 15F (8C) increase in temperature. Under no circumstances should belts be exposed to storage temperatures above 115F (46C). With a significant increase in humidity, it is possible for fungus or mildew to form on stored belts. This does not appear to cause serious belt damage, but should be avoided if possible. Equipment using belts is sometimes stored for prolonged periods (six months or more) before it is put in service or during other periods when it is idle. It is recommended that the tension of the belts be relaxed during such period and that equipment storage conditions should be consistent with the guidelines for belt storage. If this is not possible, the belts should be removed and stored separately.
GENERAL
89
Range 15mm (.5905") 20mm (.7874") 25mm (.9842") 30mm (1.181") 40mm (1.575") 50mm (1.968") 61mm (2.400")
Range 4mm (.158") 6mm (.236") 10mm (.392") 16mm (.630") 24mm (.944")
GENERAL INFORMATION
90
In addition, there are a great number of chemicals, such as gasoline, which swell rubber or extract ingredients from the belts rubber compounds. These may cause embrittlement, cracking, or swelling of the belt, which results in deterioration of performance. If the drive is subjected to the accumulation of a considerable amount of oil and grease on the belt, it may preclude the use of a V-belt or a V-ribbed belt. Synchronous belts are not substantially affected by the loss of friction coefficient and may be capable of limited operation under these conditions. As can be seen from the above, there are many variables. However, the following general guidelines might be of use in selecting a belt drive system subjected to a chemical environment. 1. Prevent the accumulation of contaminants. 2. If the belts are to be subjected to only an occasional contamination contact, a standard construction V- or synchronous belt can be used. 3. If the belts are expected to give long, trouble-free operation on an industrial drive, and they are in contact with oil or exposed to an atmosphere laden with chemicals or solvents, consult a manufacturer for recommendations.
GENERAL
91
92
MARKET BROCHURES ________ ________ ________ ________ Wood Industry PT Belts Cotton Ginning Industry PT Belts Crushed Rock & Aggregate PT Belts Truly Endless Flat Belts 20044926 20113529 20044946 20044954
ENGINEERING MANUALS ________ ________ ________ ________ ________ ________ Installation, Maintenance and Trouble Shooting Guide Industrial V-Belts Poly-V Belts (English version) Positive Drive Belts Hi-Performance Positive Drive Plus (HPPD Plus) Super Torque Positive Drive Belts
APPLICATION/CROSS REFERENCE GUIDES ________ ________ ________ ________ ________ ________ VIDEOS ________ ________ ________ ________ Maintenance & Installation V-Belt Basics Eagle Pd Sales Video Eagle Pd Installation & Maintenance Video 20044937 20044938 20113450 20039443 Variable Speed Application Guide Car & Light Truck Application Guide (current to 1994) Car & Light Truck Application Guide (1993 & prior) Medium to Heavy Duty Truck Application Guide (current to 1990) Medium to Heavy Duty Truck Application Guide (1989 & prior) Sports Vehicle (Snowmobile) Application Guide 20044912 20035740 20049146 20049138 20108695 20035750
COMPUTER PROGRAMS ________ ________ ________ MAXIMIZER Drive Analysis Software Program (USA version) MAXIMIZER Drive Analysis Software Program (Canada version) MAXIMIZER Data Gathering Form
MISCELLANEOUS ________ ________ ________ Wall Chart Product Reference Materials Make the Difference Flyer Drive Identification Stickers 20044883 20044935 20044943
GENERAL
93
________ ________
20077266 20147843
PRICE PAGES ________ ________ USA Distributor List Price Catalog Canada Distributor List Price Catalog 20113473 20044925
SALES TRAINING ________ ________ ________ Power Transmission Products Home Study Course Rubber Compounds & Materials Home Study Course Eagle Pd Training Manual 20113651 20113409 20039442
EQUIPMENT ________ ________ ________ ________ ________ ________ ________ Synchronous Belt Profile Gauge Straightedge Alignment Tool Eagle Pd Tension Tester (large 200 capacity with instructions) Eagle Pd Tension Tester (small pencil-type with instructions) Calipers Decibel Meter Tachometer 20039445 20039449 20039447 20039446 Contact Goodyear Contact Goodyear Contact Goodyear
GENERAL INFORMATION
MISCELLANEOUS ________ ________ Eagle Pd Counter Mat Eagle Pd Sales Demo Sprocket Kit 20039452 20039454
94
NOTES
95
NOTES
96