You are on page 1of 79

Log Periodic Dipole Antennas 806-960 MHz

LPA-800 Series
Our LPA (Log Periodic Antenna) 800 series is a group of log periodic dipole antennas operating within the 806-960 MHz frequency spectrum. These vertically polarized antennas feature the same true log periodic design as our classic LPD series, but are designed for more stringent zoning requirements with lighter weights and low profiles. The LPA design features more active elements than industry standard log periodic antennas. This dynamic, multiple array allows quick roll-off in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which contributes to the control of soft hand-off and pilot pollution. Design and Construction of the LPA-800 Log Periodic: LPA antennas are manufactured with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent frontto-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints in the signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipation to minimize plate warping and bending. Model Number Guide: LPA- 800 63 / 6 CF E-DIN 5 Electrical Downtilt Connector Type NE is an elongated N connector E-DIN is an elongated DIN connector CF refers to a Center-Fed connector Number of element sets Also refers to the approx. length in feet Horizontal Beamwidth Operating Frequency Range 800 = Operates within 806-960 MHz
The LPA-4016 and LPA-4019 are exceptions to above example. Check specification sheet for more information.

Models Currently Available: Model Number LPA-4016 _ LPA-4019 _ LPA-80063/4CF _ LPA-80063/6CF _ LPA-80063/8CF _ LPA-80080/4CF _ LPA-80080/6CF _ LPA-80080/8CF _ LPA-80090/4CF _ LPA-80090/8CF _ Frequency Range (MHz) 806-941 MHz 806-941 MHz 806-960 MHz 806-960 MHz 806-960 MHz 806-960 MHz 806-960 MHz 806-960 MHz 806-960 MHz 806-960 MHz H-Plane 40 40 63 63 63 80 80 80 90 90 E-Plane 14 7 15 10 7 15 10 7 15 7 Gain (dBd) 16 dBd 19 dBd 13 dBd 14.5 dBd 16 dBd 12.5 dBd 14 dBd 15 dBd 11.5 dBd 14.5 dBd Fixed Electrical Downtilt Options* 1.25, 5 1.25, 3, 5 0, 5 0, 2, 5 0, 2, 5 0, 5 0, 2, 5 0, 2, 3, 5 0, 5 0, 3, 5 Length x Width x Depth (in inches) 47.2 x 21.3 x 13.7 94.5 x 21.3 x 13.7 47.4 x 15.2 x 13.2 70.9 x 15.0 x 13.1 94.5 x 15.2 x 13.2 47.2 x 5.5 x 13.2 70.9 x 5.5 x 13.2 94.5 x 5.5 x 13.2 47.2 x 5.5 x 9.4 94.5 x 5.5 x 9.4

*Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range. When ordering replace __ with the connector type (NE or E-DIN).

Amphenol Antel, Inc.

Vertically Polarized, Log Periodic 40 / 16 dBd

Mechanical specifications
Length Width 1200 mm 545 mm 47.2 in 21.3 in 13.7 in 15.4 in 23 lbs
-140 -150 -120 -130

LPA-4016 __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 350 mm Depth with z-bracket 390 mm


4)

Weight Wind Area Fore/Aft Side

10.4 kg 0.39 m2 0.47 m2

4.20 ft2 5.03 ft2

-160 -170 180

5)

Rated Wind Velocity (Safety factor 2.0) >277 km/hr >172 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 600 N 135 lbs Side 609 N 137 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 40 130 120 60 110 100 90 80 70 50

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 16 dBd 500 W 40 14 1.25 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. 5) Worst case at 15 mechanical downtilt. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 16 dBd

Mechanical specifications
Length Width 1200 mm 545 mm 47.2 in 21.3 in 13.7 in 15.4 in 23 lbs
-140 -150 -120 -130

LPA-4016 __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 350 mm Depth with z-bracket 390 mm


4)

Weight Wind Area Fore/Aft Side

10.4 kg 0.39 m2 0.47 m2

4.20 ft2 5.03 ft2

-160 -170 180

5)

Rated Wind Velocity (Safety factor 2.0) >277 km/hr >172 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 600 N 135 lbs Side 609 N 137 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 40 130 120 60 110 100 90 80 70 50

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 16 dBd 500 W 40 14 5 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. 5) Worst case at 15 mechanical downtilt. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 19 dBd

Mechanical specifications
Length Width 2400 mm 545 mm 94.5 in 21.3 in 13.7 in 15.4 in 41 lbs
-140 -150 -120 -130

LPA-4019 __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 350 mm Depth with z-bracket 390 mm


4)

Weight Wind Area Fore/Aft Side

18.6 kg 0.78 m2 0.96 m2

8.35 ft2 10.37 ft2

-160 -170 180

5)

Rated Wind Velocity (Safety factor 2.0) >192 km/hr >119 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1245 N 280 lbs Side 1483 N 279 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 40 130 120 60 110 100 90 80 70 50

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 19 dBd 500 W 40 7 1.25 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. 5) Worst case at 15 mechanical downtilt. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 19 dBd

Mechanical specifications
Length Width 2400 mm 545 mm 94.5 in 21.3 in 13.7 in 15.4 in 41 lbs
-140 -150 -120 -130

LPA-4019 __ 3
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 350 mm Depth with z-bracket 390 mm


4)

Weight Wind Area Fore/Aft Side

18.6 kg 0.78 m2 0.96 m2

8.35 ft2 10.37 ft2

-160 -170 180

5)

Rated Wind Velocity (Safety factor 2.0) >192 km/hr >119 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1245 N 280 lbs Side 1483 N 279 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 40 130 120 60 110 100 90 80 70 50

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 19 dBd 500 W 40 7 3 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. 5) Worst case at 15 mechanical downtilt. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 19 dBd

Mechanical specifications
Length Width 2400 mm 545 mm 94.5 in 21.3 in 13.7 in 15.4 in 41 lbs
-140 -150 -120 -130

LPA-4019 __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 350 mm Depth with z-bracket 390 mm


4)

Weight Wind Area Fore/Aft Side

18.6 kg 0.78 m2 0.96 m2

8.35 ft2 10.37 ft2

-160 -170 180

5)

Rated Wind Velocity (Safety factor 2.0) >192 km/hr >119 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1245 N 280 lbs Side 1483 N 279 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 40 130 120 60 110 100 90 80 70 50

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-900 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 19 dBd 500 W 40 7 5 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. 5) Worst case at 15 mechanical downtilt. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 13 dBd

Mechanical specifications
Length Width 1205 mm 386 mm 47.4 in 15.2 in 13.2 in 14.8 in 20.0 lbs
-14 0 -150 -120 -130

LPA-80063/4CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

9.1 kg 0.47 m2 0.40 m2

5.0 ft2 4.4 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >351 km/hr >218 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 665 N 149.5 lbs Side 577 N 129.6 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 180 170 160 150 140 130 120 6 0 110 100 90 80 70 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 2 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket and Downtilt Bracket Kit #21699999

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 13 dBd 500 W 63 15 0 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 13 dBd

Mechanical specifications
Length Width 1205 mm 386 mm 47.4 in 15.2 in 13.2 in 14.8 in 20.0 lbs
-14 0 -150 -120 -130

LPA-80063/4CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

9.1 kg 0.47 m2 0.40 m2

5.0 ft2 4.4 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >351 km/hr >218 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 665 N 149.5 lbs Side 577 N 129.6 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 180 170 160 150 140 130 120 6 0 110 100 90 80 70 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 2 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket and Downtilt Bracket Kit #21699999

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 13 dBd 500 W 63 15 5 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 14.5 dBd

Mechanical specifications
Length Width 1800 mm 380 mm 70.9 in 15.0 in 13.1 in 14.6 in 27.0 lbs
-14 0 -150 -120 -130

LPA-80063/6CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 332 mm Depth with z-bracket 372 mm


4)

Weight Wind Area Fore/Aft Side

12.3 kg 0.68 m2 0.60 m2

7.4 ft2 6.5 ft2

-16 0 -170 180 170 160 150

Rated Wind Velocity (Safety factor 2.0) >235 km/hr >146 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 993 N 223.3 lbs Side 872 N 196.1 lbs

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14.5 dBd 500 W 63 10 0 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 14.5 dBd

Mechanical specifications
Length Width 1800 mm 380 mm 70.9 in 15.0 in 13.1 in 14.6 in 27.0 lbs
-14 0 -150 -120 -130

LPA-80063/6CF __ 2
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 332 mm Depth with z-bracket 372 mm


4)

Weight Wind Area Fore/Aft Side

12.3 kg 0.68 m2 0.60 m2

7.4 ft2 6.5 ft2

-16 0 -170 180 170 160 150

Rated Wind Velocity (Safety factor 2.0) >235 km/hr >146 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 993 N 223.3 lbs Side 872 N 196.1 lbs

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14.5 dBd 500 W 63 10 2 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 14.5 dBd

Mechanical specifications
Length Width 1800 mm 380 mm 70.9 in 15.0 in 13.1 in 14.6 in 27.0 lbs
-14 0 -150 -120 -130

LPA-80063/6CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 332 mm Depth with z-bracket 372 mm


4)

Weight Wind Area Fore/Aft Side

12.3 kg 0.68 m2 0.60 m2

7.4 ft2 6.5 ft2

-16 0 -170 180 170 160 150

Rated Wind Velocity (Safety factor 2.0) >235 km/hr >146 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 993 N 223.3 lbs Side 872 N 196.1 lbs

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14.5 dBd 500 W 63 10 5 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 16 dBd

Mechanical specifications
Length Width 2400 mm 386 mm 94.5 in 15.2 in 13.2 in 14.8 in 38.0 lbs
-140 -150 -120 -130

LPA-80063/8CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

17.2 kg 0.93 m2 0.80 m2

10.0 ft2 8.7 ft2

-160 -170 180

Rated Wind Velocity (Safety factor 2.0) >276 km/hr >172 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1357 N 305 lbs Side 1197 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 16 dBd 500 W 63 7 0 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 16 dBd

Mechanical specifications
Length Width 2400 mm 386 mm 94.5 in 15.2 in 13.2 in 14.8 in 38.0 lbs
-140 -150 -120 -130

LPA-80063/8CF __ 2
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

17.2 kg 0.93 m2 0.80 m2

10.0 ft2 8.7 ft2

-160 -170 180

Rated Wind Velocity (Safety factor 2.0) >276 km/hr >172 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1357 N 305 lbs Side 1197 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 16 dBd 500 W 63 7 2 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 63 / 16 dBd

Mechanical specifications
Length Width 2400 mm 386 mm 94.5 in 15.2 in 13.2 in 14.8 in 38.0 lbs
-140 -150 -120 -130

LPA-80063/8CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

17.2 kg 0.93 m2 0.80 m2

10.0 ft2 8.7 ft2

-160 -170 180

Rated Wind Velocity (Safety factor 2.0) >276 km/hr >172 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1357 N 305 lbs Side 1197 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 16 dBd 500 W 63 7 5 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 12.5 dBd

Mechanical specifications
Length Width 1200 mm 140 mm 47.2 in 5.5 in 13.2 in 14.8 in 12.0 lbs
-140 -150 -120 -130

LPA-80080/4CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

5.4 kg 0.17 m2 0.40 m2

1.8 ft2 4.3 ft2

-160 -170 180 170 160 150

Rated Wind Velocity (Safety factor 2.0) >369 km/hr >229 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 254 N 57.1 lbs Side 574 N 129.0 lbs
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 60 110 100 90 80 70 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 12.5 dBd 500 W 80 15 0 15% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 12.5 dBd

Mechanical specifications
Length Width 1200 mm 140 mm 47.2 in 5.5 in 13.2 in 14.8 in 12.0 lbs
-140 -150 -120 -130

LPA-80080/4CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

5.4 kg 0.17 m2 0.40 m2

1.8 ft2 4.3 ft2

-160 -170 180 170 160 150

Rated Wind Velocity (Safety factor 2.0) >369 km/hr >229 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 254 N 57.1 lbs Side 574 N 129.0 lbs
Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 180 170 160 150 140 130 120 60 110 100 90 80 70 50 40 30 35 30 25 20 15 10 5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 12.5 dBd 500 W 80 15 5 15% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 14 dBd

Mechanical specifications
Length Width 1800 mm 140 mm 70.9 in 5.5 in 13.2 in 14.8 in 21.0 lbs
-140 -150 -120 -130

LPA-80080/6CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

9.5 kg 0.25 m2 0.60 m2

2.7 ft2 6.5 ft2

-160 -170 180

Rated Wind Velocity (Safety factor 2.0) >295 km/hr >183 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 415 N 93.3 lbs Side 870 N 195.6 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14 dBd 500 W 80 10 0 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 14 dBd

Mechanical specifications
Length Width 1800 mm 140 mm 70.9 in 5.5 in 13.2 in 14.8 in 21.0 lbs
-140 -150 -120 -130

LPA-80080/6CF __ 2
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

9.5 kg 0.25 m2 0.60 m2

2.7 ft2 6.5 ft2

-160 -170 180

Rated Wind Velocity (Safety factor 2.0) >295 km/hr >183 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 415 N 93.3 lbs Side 870 N 195.6 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14 dBd 500 W 80 10 2 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 14 dBd

Mechanical specifications
Length Width 1800 mm 140 mm 70.9 in 5.5 in 13.2 in 14.8 in 21.0 lbs
-140 -150 -120 -130

LPA-80080/6CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

9.5 kg 0.25 m2 0.60 m2

2.7 ft2 6.5 ft2

-160 -170 180

Rated Wind Velocity (Safety factor 2.0) >295 km/hr >183 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 415 N 93.3 lbs Side 870 N 195.6 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in) Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14 dBd 500 W 80 10 5 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 15 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 13.2 in 14.8 in 24.0 lbs
-14 0 -150 -120 -130

LPA-80080/8CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

10.9 kg 0.34 m2 0.81 m2

3.6 ft2 8.7 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 580 N 130 lbs Side 1198 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 15 dBd 500 W 80 7 0 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 15 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 13.2 in 14.8 in 24.0 lbs
-14 0 -150 -120 -130

LPA-80080/8CF __ 2
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

10.9 kg 0.34 m2 0.81 m2

3.6 ft2 8.7 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 580 N 130 lbs Side 1198 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 15 dBd 500 W 80 7 2 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 15 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 13.2 in 14.8 in 24.0 lbs
-14 0 -150 -120 -130

LPA-80080/8CF __ 3
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

10.9 kg 0.34 m2 0.81 m2

3.6 ft2 8.7 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 580 N 130 lbs Side 1198 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 15 dBd 500 W 80 7 3 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 15 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 13.2 in 14.8 in 24.0 lbs
-14 0 -150 -120 -130

LPA-80080/8CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 335 mm Depth with z-bracket 375 mm


4)

Weight Wind Area Fore/Aft Side

10.9 kg 0.34 m2 0.81 m2

3.6 ft2 8.7 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 580 N 130 lbs Side 1198 N 269 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 15 dBd 500 W 80 7 5 10% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 90 / 11.5 dBd

Mechanical specifications
Length Width 1200 mm 140 mm 47.2 in 5.5 in 9.4 in 11.0 in 11.0 lbs
-14 0 -150 -120 -130

LPA-80090/4CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 240 mm Depth with z-bracket 280 mm


4)

Weight Wind Area Fore/Aft Side

5 kg 0.17 m2 0.29 m2

1.8 ft2 3.1 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >444 km/hr >276 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 254 N 57.1 lbs Side 415 N 93.3 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 11.5 dBd 500 W 90 15 0 10-15% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 90 / 11.5 dBd

Mechanical specifications
Length Width 1200 mm 140 mm 47.2 in 5.5 in 9.4 in 11.0 in 11.0 lbs
-14 0 -150 -120 -130

LPA-80090/4CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 240 mm Depth with z-bracket 280 mm


4)

Weight Wind Area Fore/Aft Side

5 kg 0.17 m2 0.29 m2

1.8 ft2 3.1 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >444 km/hr >276 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 254 N 57.1 lbs Side 415 N 93.3 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 11.5 dBd 500 W 90 15 5 10-15% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 90 / 14.5 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 9.4 in 11.0 in 22.0 lbs
-14 0 -150 -120 -130

LPA-80090/8CF __
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 240 mm Depth with z-bracket 280 mm


4)

Weight Wind Area Fore/Aft Side

10 kg 0.34 m2 0.58 m2

3.6 ft2 6.2 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 582 N 131.0 lbs Side 896 N 201.5 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14.5 dBd 500 W 90 7 0 15% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 90 / 14.5 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 9.4 in 11.0 in 22.0 lbs
-14 0 -150 -120 -130

LPA-80090/8CF __ 3
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 240 mm Depth with z-bracket 280 mm


4)

Weight Wind Area Fore/Aft Side

10 kg 0.34 m2 0.58 m2

3.6 ft2 6.2 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 582 N 131.0 lbs Side 896 N 201.5 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14.5 dBd 500 W 90 7 3 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 90 / 14.5 dBd

Mechanical specifications
Length Width 2400 mm 140 mm 94.5 in 5.5 in 9.4 in 11.0 in 22.0 lbs
-14 0 -150 -120 -130

LPA-80090/8CF __ 5
When ordering replace ___ with connector type.

Radiation pattern1)
-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Depth 240 mm Depth with z-bracket 280 mm


4)

Weight Wind Area Fore/Aft Side

10 kg 0.34 m2 0.58 m2

3.6 ft2 6.2 ft2

-16 0 -170 180

Rated Wind Velocity (Safety factor 2.0) >340 km/hr >211 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 582 N 131.0 lbs Side 896 N 201.5 lbs

170 160 150

Antenna consisting of aluminum alloy with brass feedlines covered by a UV safe fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -16 0 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-102 mm (2.0-4.0 in). If the lock-down brace is used, the maximum diameter is 88.9 mm (3.5 in). Mounting Bracket & Downtilt Bracket Kit #21699999

180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-960 MHz 50 NE or E-DIN 1 port / center 1.4:1 Vertical 14.5 dBd 500 W 90 7 5 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Unique feedline design eliminates the need for conventional solder joints in the signal path. A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Featuring upper side lobe suppression.


Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

CF Denotes a Center-Fed Connector.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Mounting & Downtilt Bracket Kits

LPA Bracket Kits


Part Number
21699999

Bracket Type
Standard LPA Mounting & Downtilt Bracket Kit* for: LPA-4016 LPA-4019 LPA-80063/4CF LPA-80063/6CF LPA-80063/8CF LPA-80080/4CF LPA-80080/6CF LPA-80080/8CF LPA-80090/4CF LPA-80090/8CF

21699999

Top View

Side View

*The LPA downtilt bracket kit includes the standard mounting kit.

Mounting Bracket Kits are sold separately and not included in the price of antennas.

1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Vertically Polarized Log Periodic Dipole Antennas 806-900 MHz, 806-941 MHz, 806-960 MHz
LPD Series
The LPD (Log Periodic Dipole) series is a group of log periodic antennas operating within the 806-900 MHz, 806-941 MHz, and 806960 MHz frequency range. These antennas are an ideal choice for sectorized sites in which performance is the priority. LPDs offer a true log periodic design with more active elements than industry standard antennas. This dynamic, multiple array allows quick rolloff in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which contributes to the control of soft hand-off and pilot pollution. Design and Construction of the LPD Log Periodic: LPD antennas are manufactured. with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent frontto-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints in the signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipation to minimize plate warping and bending. Model Number Guide: LPD 790 8 / 4 E-DIN

3 Electrical Downtilt Connector Type NE is an elongated N connector E-DIN is an elongated DIN connector References Antenna Length in Feet Horizontal Beamwidth: 8 = 60, 7 = 80, 5 = 92 Operating Frequency Range 790 = Operates within 806-960 MHz

This rule does not apply to the LPD-7905/4/102 and LPD-7905/8/102.

Exceptions: The following antenna models are exceptions to the examples shown above: LPD-4016, LPD-4019, LPD-6513, and LPD-6516

LPD

65

13 E-DIN 5 Electrical Downtilt Connector Type NE is an elongated N connector E-DIN is an elongated DIN connector Gain in dBd Horizontal Beamwidth

Models Currently Available: Model Number LPD-4013 _ LPD-4016 _ LPD-4019 _ LPD-7908 _ LPD-7908/2 _ LPD-7908/4 _ LPD-6513 _ Frequency Range (MHz) 806-900 MHz* 806-941 MHz* 806-960 MHz 806-900 MHz* 806-900 MHz* 806-900 MHz* 806-941 MHz* H-Plane 40 40 40 60 60 60 65 E-Plane 30 14 7 53 26 13 15 Gain (dBd) 13 dBd 16 dBd 19 dBd 8 dBd 11 dBd 14 dBd 13 dBd Fixed Electrical Length x Width x Depth Downtilt Options** (in inches) 1.25 1.25, 3, 5, 9 1.25, 3, 5 0 0 1.25, 3, 5, 9 1.25, 3, 5, 9 23.6 x 21.3 x 13.7 47.2 x 21.3 x 13.7 94.5 x 21.3 x 13.7 11.8 x 5.1 x 25.2 23.6 x 5.1 x 25.2 47.3 x 5.1 x 25.2 47.2 x 13.9 x 11.2

Continued on next page ...


*This model is also available up to 960 MHz. Contact your sales representative for details. **Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range. When ordering replace __ with the connector type (NE or E-DIN).

Amphenol Antel, Inc.

LPD Series Continued


Models Currently Available: Model Number LPD-6516 _ LPD-7907 _ LPD-7907/2 _ LPD-7907/4 _ LPD-7907/8 _ LPD-7905 _ LPD-7905/2 _ LPD-7905/4 _ LPD-7905/8 _ LPD-7905/4/102 _ LPD-7905/8/102 _ Frequency Range (MHz) 806-960 MHz* 806-900 MHz* 806-900 MHz* 806-960 MHz 806-900 MHz* 806-941 MHz* 806-900 MHz* 806-941 MHz* 806-960 MHz 806-941 MHz* 806-941 MHz* H-Plane 65 80 80 80 80 92 92 92 92 102 102 E-Plane 7 56 28 14 7 60 30 15 7 15 7 Gain (dBd) 16 dBd 7 dBd 10 dBd 13 dBd 16 dBd 5 dBd 8 dBd 11.5 dBd 14.5 dBd 10.5 dBd 13.5 dBd Fixed Electrical Length x Width x Depth Downtilt Options** (in inches) 1.25, 3, 5 0 0 1.25, 3, 5, 9 1.25, 3, 5 0 0 1.25, 3, 5, 9 1.25, 3, 5 1.25, 3, 5, 9 1.25, 3, 5 94.5 x 13.9 x 11.2 11.8 x 5.1 x 14.8 23.6 x 5.1 x 14.8 47.2 x 5.1 x 14.8 94.5 x 5.1 x 14.8 11.8 x 5.1 x 9.6 23.6 x 5.1 x 9.6 47.2 x 5.1 x 9.6 94.5 x 5.1 x 9.6 47.2 x 5.1 x 9.6 94.5 x 5.1 x 9.6

*This model is also available up to 960 MHz. Contact your sales representative for details. **Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range. When ordering replace __ with the connector type (NE or E-DIN).

Amphenol Antel, Inc.

Vertically Polarized, Log Periodic 40 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4013 __
When ordering replace ___ with connector type.

600 mm 545 mm 350 mm 7.7 kg 0.19 m2 0.22 m2

23.6 in 21.3 in 13.7 in 17.0 lbs


-130 -110 -120 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 40 130 120 110 6 0 100 90 80 70 50

Radiation pattern1)

Weight Wind Area Fore/Aft Side

2.0 ft2 2.4 ft2

e in th -14 0 ulls ane -150 No N -Pl -16 0 H


-170 180 170 160 150

Rated Wind Velocity (Safety factor 2.0) >531 km/hr >330 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 282 N 63 lbs Side 326 N 73 lbs

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001
-16 0 -170 180

Electrical specifications
Frequency Range Impedance
3)

170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13 dBd 500 W 40 30 1.25 5% Direct Ground

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Vertical

1)

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.
1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4016 __
When ordering replace ___ with connector type.

1200 mm 545 mm 350 mm 15.4 kg 0.38 m2 0.47 m2

47.2 in 21.3 in 13.7 in 34.0 lbs

Radiation pattern1)
-110 -120 -130 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

4.05 ft2 5.05 ft2

e n th -14 0 lls ine u -150 No N -Pla -16 0 H


-170 180 170 160 150

This model has been replaced with the LPA-4016 _

5)

Rated Wind Velocity (Safety factor 2.0) >443 km/hr >275 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 578 N 130 lbs Side 694 N 156 lbs

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 40 14 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4016 __ 3
When ordering replace ___ with connector type.

1200 mm 545 mm 350 mm 15.4 kg 0.38 m2 0.47 m2

47.2 in 21.3 in 13.7 in 34.0 lbs

Radiation pattern1)
-110 -120 -130 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

4.05 ft2 5.05 ft2

e n th -14 0 lls ine u -150 No N -Pla -16 0 H


-170 180 170 160 150

5)

Rated Wind Velocity (Safety factor 2.0) >443 km/hr >275 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 578 N 130 lbs Side 694 N 156 lbs

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 40 14 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4016 __ 5
When ordering replace ___ with connector type.

1200 mm 545 mm 350 mm 15.4 kg 0.38 m2 0.47 m2

47.2 in 21.3 in 13.7 in 34.0 lbs

Radiation pattern1)
-110 -120 -130 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

4.05 ft2 5.05 ft2

e n th -14 0 lls ine u -150 No N -Pla -16 0 H


-170 180 170 160 150

This model has been replaced with the LPA-4016 _ 5

5)

Rated Wind Velocity (Safety factor 2.0) >443 km/hr >275 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 578 N 130 lbs Side 694 N 156 lbs

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 40 14 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4016 __ 9
When ordering replace ___ with connector type.

1200 mm 545 mm 350 mm 15.4 kg 0.38 m2 0.47 m2

47.2 in 21.3 in 13.7 in 34.0 lbs

Radiation pattern1)
-110 -120 -130 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

4.05 ft2 5.05 ft2

e n th -14 0 lls ine u -150 No N -Pla -16 0 H


-170 180 170 160 150

5)

Rated Wind Velocity (Safety factor 2.0) >443 km/hr >275 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 578 N 130 lbs Side 694 N 156 lbs

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 40 14 9 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 19 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4019 __
When ordering replace ___ with connector type.

2400 mm 545 mm 350 mm 30.9 kg 0.75 m2 0.95 m2

94.5 in 21.3 in 13.7 in 68.0 lbs

Radiation pattern1)
-110 -120 -130 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

8.1 ft2 10.2 ft2

e -14 0 n th lls ine u -150 No N -Pla -16 0 H


-170 180 170 160 150

This model has been replaced with the LPA-4019 _.

5)

Rated Wind Velocity (Safety factor 2.0) >311 km/hr >193 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1206 N 271 lbs Side 1450 N 326 lbs

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.25:1 Vertical 19 dBd 500 W 40 7 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 19 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4019 __ 3
When ordering replace ___ with connector type.

2400 mm 545 mm 350 mm 30.9 kg 0.75 m2 0.95 m2

94.5 in 21.3 in 13.7 in 68.0 lbs

Radiation pattern1)
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

This model has been replaced with the LPA-4019 _ 3.

8.1 ft2 10.2 ft2


-170

-150 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >311 km/hr >193 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1206 N 271 lbs Side 1450 N 326 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.25:1 Vertical 19 dBd 500 W 40 7 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 40 / 19 dBd

Mechanical specifications
Length Width Depth
4)

LPD-4019 __ 5
When ordering replace ___ with connector type.

2400 mm 545 mm 350 mm 30.9 kg 0.75 m2 0.95 m2

94.5 in 21.3 in 13.7 in 68.0 lbs

Radiation pattern1)
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 6 0 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

This model has been replaced with the LPA-4019 _ 5.

8.1 ft2 10.2 ft2


-170

-150 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >311 km/hr >193 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 1206 N 271 lbs Side 1450 N 326 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 19 dBd 500 W 40 7 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 60 / 8 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7908 __
When ordering replace ___ with connector type.

300 mm 130 mm 640 mm 3.5 kg 0.04 m2 0.09 m2

11.8 in 5.1 in 25.2 in 7.7 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

0.42 ft2 0.97 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >512 km/hr >381 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 56 N 12.5 lbs Side 129 N 29.0 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 8 dBd 500 W 60 53 Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane Lightning Protection

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.

*Also available up to 960 MHz. Consult your sales director for more information.

Antenna available with center-fed connector only.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 60 / 11 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7908/2 __
When ordering replace ___ with connector type.

600 mm 130 mm 640 mm 7.3 kg 0.08 m2 0.28 m2

23.6 in 5.1 in 25.2 in 16.2 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 60 110 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

0.84 ft2 3.04 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >338 km/hr >210 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 112 N 25 lbs Side 400 N 90 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 11 dBd 500 W 60 26 Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane Lightning Protection

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.

*Also available up to 960 MHz. Consult your sales director for more information.

Antenna available with center-fed connector only.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 60 / 14 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7908/4 __
When ordering replace ___ with connector type.

1200 mm 130 mm 640 mm 16 kg 0.16 m2 0.66 m2

47.3 in 5.1 in 25.2 in 35.3 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 7.06 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >269 km/hr >168 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 930 N 209 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14 dBd 500 W 60 13 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 60 / 14 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7908/4 __ 3
When ordering replace ___ with connector type.

1200 mm 130 mm 640 mm 16 kg 0.16 m2 0.66 m2

47.3 in 5.1 in 25.2 in 35.3 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 7.06 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >269 km/hr >168 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 930 N 209 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14 dBd 500 W 60 13 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 60 / 14 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7908/4 __ 5
When ordering replace ___ with connector type.

1200 mm 130 mm 640 mm 16 kg 0.16 m2 0.66 m2

47.3 in 5.1 in 25.2 in 35.3 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 7.06 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >269 km/hr >168 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 930 N 209 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14 dBd 500 W 60 13 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 60 / 14 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7908/4 __ 9
When ordering replace ___ with connector type.

1200 mm 130 mm 640 mm 16 kg 0.16 m2 0.66 m2

47.3 in 5.1 in 25.2 in 35.3 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 7.06 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >269 km/hr >168 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 930 N 209 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14 dBd 500 W 60 13 9 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6513 __
When ordering replace ___ with connector type.

1200 mm 355 mm 285 mm 10 kg 0.31 m2 0.40 m2

47.2 in 14.0 in 11.2 in 28.0 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.28 ft2 4.29 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >499 km/hr >310 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 475 N 107 lbs Side 593 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.35:1 Vertical 13 dBd 500 W 65 15 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6513 __ 3
When ordering replace ___ with connector type.

1200 mm 355 mm 285 mm 10 kg 0.31 m2 0.40 m2

47.2 in 14.0 in 11.2 in 28.0 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.28 ft2 4.29 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >499 km/hr >310 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 475 N 107 lbs Side 593 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.35:1 Vertical 13 dBd 500 W 65 15 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6513 __ 5
When ordering replace ___ with connector type.

1200 mm 355 mm 285 mm 10 kg 0.31 m2 0.40 m2

47.2 in 14.0 in 11.2 in 28.0 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.28 ft2 4.29 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >499 km/hr >310 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 475 N 107 lbs Side 593 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.35:1 Vertical 13 dBd 500 W 65 15 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6513 __ 9
When ordering replace ___ with connector type.

1200 mm 355 mm 285 mm 10 kg 0.31 m2 0.40 m2

47.2 in 14.0 in 11.2 in 28.0 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.28 ft2 4.29 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >499 km/hr >310 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 475 N 107 lbs Side 593 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.35:1 Vertical 13 dBd 500 W 65 15 9 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6516 __
When ordering replace ___ with connector type.

2400 mm 355 mm 285 mm 27.4 kg 0.61 m2 0.81 m2

94.5 in 14.0 in 11.2 in 60.5 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

6.51 ft2 8.69 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >344 km/hr >214 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 966 N 224 lbs Side 1244 N 280 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 16 dBd 500 W 65 7 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6516 __ 3
When ordering replace ___ with connector type.

2400 mm 355 mm 285 mm 27.4 kg 0.61 m2 0.81 m2

94.5 in 14.0 in 11.2 in 60.5 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

6.51 ft2 8.69 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >344 km/hr >214 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 966 N 224 lbs Side 1244 N 280 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.35:1 Vertical 16 dBd 500 W 65 7 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 65 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-6516 __ 5
When ordering replace ___ with connector type.

2400 mm 355 mm 285 mm 27.4 kg 0.61 m2 0.81 m2

94.5 in 14.0 in 11.2 in 60.5 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

6.51 ft2 8.69 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >344 km/hr >214 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 966 N 224 lbs Side 1244 N 280 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome. Aluminum reflector.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.35:1 Vertical 16 dBd 500 W 65 7 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 7 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907 __
When ordering replace ___ with connector type.

300 mm 130 mm 375 mm 2.5 kg 0.04 m2 0.08 m2

11.8 in 5.1 in 14.8 in 5.5 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

0.42 ft2 0.83 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >945 km/hr >587 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 56 N 13 lbs Side 109 N 25 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 7 dBd 500 W 80 56 0 Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane Electrical Downtilt Lightning Protection

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.

*Also available up to 960 MHz. Consult your sales director for more information.

Antenna available with center-fed connector only.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 10 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/2 __
When ordering replace ___ with connector type.

600 mm 130 mm 375 mm 5.5 kg 0.08 m2 0.19 m2

23.6 in 5.1 in 14.8 in 12.2 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

0.84 ft2 2.03 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >517 km/hr >321 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 112 N 25 lbs Side 267 N 60 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 10 dBd 500 W 80 28 0 Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane Electrical Downtilt Lightning Protection

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.

*Also available up to 960 MHz. Consult your sales director for more information.

Antenna available with center-fed connector only.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/4 __
When ordering replace ___ with connector type.

1200 mm 130 mm 375 mm 12 kg 0.16 m2 0.41 m2

47.2 in 5.1 in 14.8 in 26.5 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 4.46 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >420 km/hr >261 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 590 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13 dBd 500 W 80 14 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/4 __ 3
When ordering replace ___ with connector type.

1200 mm 130 mm 375 mm 12 kg 0.16 m2 0.41 m2

47.2 in 5.1 in 14.8 in 26.5 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 4.46 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >420 km/hr >261 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 590 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13 dBd 500 W 80 14 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/4 __ 5
When ordering replace ___ with connector type.

1200 mm 130 mm 375 mm 12 kg 0.16 m2 0.41 m2

47.2 in 5.1 in 14.8 in 26.5 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 4.46 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >420 km/hr >261 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 590 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13 dBd 500 W 80 14 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 13 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/4 __ 9
When ordering replace ___ with connector type.

1200 mm 130 mm 375 mm 12 kg 0.16 m2 0.41 m2

47.2 in 5.1 in 14.8 in 26.5 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 4.46 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >420 km/hr >261 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 590 N 133 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -150 -160 -170 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13 dBd 500 W 80 14 9 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/8 __
When ordering replace ___ with connector type.

2400 mm 130 mm 375 mm 25 kg 0.31 m2 0.83 m2

94.5 in 5.1 in 14.8 in 55.0 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

3.36 ft2 8.90 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >291 km/hr >181 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 1217 N 274 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 80 7 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/8 __ 3
When ordering replace ___ with connector type.

2400 mm 130 mm 375 mm 25 kg 0.31 m2 0.83 m2

94.5 in 5.1 in 14.8 in 55.0 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

3.36 ft2 8.90 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >291 km/hr >181 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 1217 N 274 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 80 7 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 80 / 16 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7907/8 __ 5
When ordering replace ___ with connector type.

2400 mm 130 mm 375 mm 25 kg 0.31 m2 0.83 m2

94.5 in 5.1 in 14.8 in 55.0 lbs

Radiation pattern1)
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 60 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

3.36 ft2 8.90 ft2


-170

-150 -160

5)

Rated Wind Velocity (Safety factor 2.0) >291 km/hr >181 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 1217 N 274 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -140 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 20 30 140 130 120 110 100 90 80 70 60 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-150 -160 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 16 dBd 500 W 80 7 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905 __
When ordering replace ___ with connector type.

300 mm 130 mm 245 mm 2.2 kg 0.04 m2 0.05 m2

11.8 in 5.1 in 9.6 in 4.9 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

0.42 ft2 0.58 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >1098 km/hr >682 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 56 N 13 lbs Side 76 N 17 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001
-15 0 -16 0 -17 0

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 5 dBd 500 W 92 60 0 Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane Electrical Downtilt Lightning Protection

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.

*Also available up to 960 MHz. Consult your sales director for more information.

Antenna available with center-fed connector only.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 8 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/2 __
When ordering replace ___ with connector type.

600 mm 130 mm 245 mm 4.5 kg 0.08 m2 0.13 m2

23.6 in 5.1 in 9.6 in 10.0 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 6 0 110 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

0.84 ft2 1.34 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >731 km/hr >454 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 112 N 25 lbs Side 177 N 40 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110002 Downtilt bracket kit #36114001

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 8 dBd 500 W 92 30 0 Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane Electrical Downtilt Lightning Protection

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.

*Also available up to 960 MHz. Consult your sales director for more information.

Antenna available with center-fed connector only.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 11.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4 __
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 11.5 dBd 500 W 92 15 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 11.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4 __ 3
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 11.5 dBd 500 W 92 15 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 11.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4 __ 5
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 11.5 dBd 500 W 92 15 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 11.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4 __ 9
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 11.5 dBd 500 W 92 15 9 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 14.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/8 __
When ordering replace ___ with connector type.

2400 mm 130 mm 245 mm 22 kg 0.31 m2 0.56 m2

94.5 in 5.1 in 9.6 in 48.7 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.36 ft2 6.07 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >403 km/hr >250 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 872 N 196 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14.5 dBd 500 W 92 7 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 14.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/8 __ 3
When ordering replace ___ with connector type.

2400 mm 130 mm 245 mm 22 kg 0.31 m2 0.56 m2

94.5 in 5.1 in 9.6 in 48.7 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.36 ft2 6.07 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >403 km/hr >250 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 872 N 196 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-960 MHz 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14.5 dBd 500 W 92 7 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-960 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 92 / 14.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/8 __ 5
When ordering replace ___ with connector type.

2400 mm 130 mm 245 mm 22 kg 0.31 m2 0.56 m2

94.5 in 5.1 in 9.6 in 48.7 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.36 ft2 6.07 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >403 km/hr >250 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 872 N 196 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -16 0 -17 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 14.5 dBd 500 W 92 7 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 10.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4/102 __
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 10.5 dBd 500 W 102 15 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 10.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4/102 __ 3
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-110 -120 -130 -14 0 -150 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 100 90 80 70 6 0 50 40

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -170

Electrical specifications
Frequency Range Impedance
3)

180 170 160 150

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 10.5 dBd 500 W 102 15 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 10.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4/102 __ 5
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 6 0 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-170

-150 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 10.5 dBd 500 W 102 15 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 10.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/4/102 __ 9
When ordering replace ___ with connector type.

1200 mm 130 mm 245 mm 10 kg 0.16 m2 0.27 m2

47.2 in 5.1 in 9.6 in 22.1 lbs

Radiation pattern1)
-110 -120 -130 -14 0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 10 2 0 30 140 130 120 110 6 0 100 90 80 70 50 40

Weight Wind Area Fore/Aft Side

1.68 ft2 2.95 ft2


-170

-150 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >599 km/hr >372 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 240 N 54 lbs Side 394 N 89 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 10.5 dBd 500 W 102 15 9 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 13.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/8/102 __
When ordering replace ___ with connector type.

2400 mm 130 mm 245 mm 22 kg 0.31 m2 0.56 m2

94.5 in 5.1 in 9.6 in 48.7 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.36 ft2 6.07 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >403 km/hr >250 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 872 N 196 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-941 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13.5 dBd 500 W 102 7 1.25 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-941 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 13.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/8/102 __ 3
When ordering replace ___ with connector type.

2400 mm 130 mm 245 mm 22 kg 0.31 m2 0.56 m2

94.5 in 5.1 in 9.6 in 48.7 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.36 ft2 6.07 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >403 km/hr >250 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 872 N 196 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13.5 dBd 500 W 102 7 3 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Vertically Polarized, Log Periodic 102 / 13.5 dBd

Mechanical specifications
Length Width Depth
4)

LPD-7905/8/102 __ 5
When ordering replace ___ with connector type.

2400 mm 130 mm 245 mm 22 kg 0.31 m2 0.56 m2

94.5 in 5.1 in 9.6 in 48.7 lbs

Radiation pattern1)
-11 0 -12 0 -130 -140 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 6 0 100 9 0 8 0 70 50 4 0

Weight Wind Area Fore/Aft Side

3.36 ft2 6.07 ft2


-17 0

-15 0 -16 0

5)

Rated Wind Velocity (Safety factor 2.0) >403 km/hr >250 mph Wind Load @ 100 mph (161 km/hr) Fore/Aft 552 N 124 lbs Side 872 N 196 lbs

180 170 160 150

Antenna consisting of brass and covered by a fiberglass radome.

Horizontal
-11 0 -12 0 -130 -140 -15 0 -10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 35 30 25 20 15 10 5 0 1 0 20 30 140 130 120 110 100 9 0 8 0 70 6 0 50 4 0

Mounting and Downtilting


Mounting brackets attach to a pipe diameter of 50-160 mm (2.0-6.3 in). Mounting bracket kit #36110003 Downtilt bracket kit #36114002
-16 0 -17 0 180 170 160 150

Electrical specifications
Frequency Range Impedance
3)

806-900 MHz* 50 NE or E-DIN 1 port / center 1.25:1 Vertical 13.5 dBd 500 W 102 7 5 5% Direct Ground

Connector(s) VSWR Polarization Gain Power Rating Half Power Angle H-Plane E-Plane

Amphenol Antels Exclusive 3T (True Transmission Line Technology) Antenna Design:


True log-periodic design allows for superior front-to-side characteristics to minimize sector overlap. Durable brass feedline design eliminates the need for conventional solder joints in the signal path.

1)

Vertical

1) 2) 1)

Radiation patterns for all antennas are measured with the antenna mounted on a fiberglass pole. Mounting on a metal pole will typically improve the Front-to-Back ratio.

A non-collinear system with access to every radiating element for broad bandwidth and superior performance. Air as insulation for virtually no internal signal loss. This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement. Antenna available with center-fed connector only.

1) 1)

Electrical Downtilt Null Fill Lightning Protection

*Also available up to 960 MHz. Consult your sales director for more information.

1) Typical values. 2) Power rating limited by connector only. 3) NE indicates an elongated N connector. E-DIN indicates an elongated DIN connector. 4) The antenna weight listed above does not include the bracket weight. Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

806-900 MHz
Tel. (815) 399-0001 www.antelinc.com Revision Date: 7/5/07

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com

Mounting & Downtilt Bracket Kits

LPD Bracket Kits


Part Number
36110002*

Bracket Type
Standard LPD Mounting Bracket Kit for: LPD-4013 LPD-7905 LPD-7905/2 LPD-7907 LPD-7907/2 LPD-7908 LPD-7908/2

36110002* & 36110003**

Top View

36110003**

Standard LPD Mounting Bracket Kit for: LPD-4016 LPD-4019 LPD-6513 LPD-6516 LPD-7905/4 LPD-7905/4/102 LPD-7905/8 LPD-7905/8/102 LPD-7907/4 LPD-7907/8 LPD-7908/4

*Braket Kit: 36110002 contains two of pictured bracket. **Bracket Kit: 36110003 contains three of pictured bracket.

Both the downtilt bracket kit and the standard mounting bracket kit must be ordered for mechanical downtilt applications.

Mounting Bracket Kits are sold separately and not included in the price of antennas.

1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Mounting & Downtilt Bracket Kits

LPD Bracket Kits


Part Number
36114001

Bracket Type
Standard LPD *Downtilt Bracket Kit for: LPD-4013 LPD-7905 LPD-7905/2 LPD-7907 LPD-7907/2 LPD-7908 LPD-7908/2

36114001

Top View

Side View

36114002

Standard LPD *Downtilt Bracket Kit for: LPD-4016 LPD-4019 LPD-6513 LPD-6516 LPD-7905/4 LPD-7905/4/102 LPD-7905/8 LPD-7905/8/102 LPD-7907/4 LPD-7907/8 LPD-7908/4

36114002

Top View

Side View

*Both the downtilt bracket kit and the standard mounting bracket kit must be ordered for mechanical downtilt applications.

Mounting Bracket Kits are sold separately and not included in the price of antennas.

1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

You might also like