Professional Documents
Culture Documents
Power Requirements
Telecommunication satellites require several kilowatts of electric power, while most other satellites require several hundred watts. The long-duration human missions, Skylab, launched in 1973, and the Russian * space station Mir, launched in 1986, each used 25 kilowatts from solar cells. The International Space Station has solar PV modules with a total rated generation capacity of 240 kilowatts at the beginning of life and 168 kilowatts at the end of life, with the life duration expected to be fifteen years. The space station's solar array has eight wings and operates at 160 volts DC. Each half-wing is 11.6 meters (38 feet) by 32.9 meters (108 feet). In each wing, there are 32,800 square silicon cells that are 8 centimeters (3.15 inches) by 8 centimeters by 0.2 centimeters (0.08 inches) thick with an average conversion efficiency of 14.2 percent. The total power of the solar array of the International Space Station is more than 2 million times larger than the first solar panels on Vanguard I. While the demand for power by commercial communication satellites is increasing, National Aeronautics and Space Administration (NASA) missions to near-Earth targets, such as Mars or the Moon, and scientific missions to the Sun and outer planets, have been requiring decreasing amounts of power. The piloted missionswhether Earth orbiting, lunar, or plane-taryrequire power systems that are an order of magnitude larger than that of the largest telecommunication power systems.
In the 1980s and 1990s gallium arsenide-based solar cells were developed. Gallium arsenide on germanium solar cells were developed to increase the size and to reduce the thickness of cells by increasing the mechanical strength. Multijunction cells using gallium arsenide, gallium-aluminum arsenide, and gallium-aluminum phosphide on germanium were developed to effectively use a larger portion of the solar spectrum. Typical efficiencies for gallium arsenide-based cells range from 18.5 percent for single junction diodes to 24 percent for triple junction diodes. Gallium arsenide cells are used for critical space missions that require high power. The manufacturing costs of gallium arsenide on germanium cells are six to nine times that of silicon cells. The overall cost is reduced, however, because of the higher efficiency of the cells. More satellites can be launched on a single rocket because of the smaller array area. Limiting the total area of the solar array is an important factor in the viability of space power arrays because of the estimated altitude control costs, which for a ten-year geosynchronous Earth orbit (GEO) mission amount to $48,000 per square meter. In this regard, high-efficiency multi junction arrays are more attractive for missions requiring higher power. Megawatts of power required by larger satellite constellations will be satisfied with multijunction solar cells having still higher efficiencies of greater than 30 percent. Iridium, a constellation of sixty-six communication satellites, required a total power of 125 kilowatts and used gallium arsenide on germanium solar cells. The spectacular performance of the Pathfinder mission to Mars was made possible by the mission's gallium arsenide on germanium cells. The cells provided all the necessary power, including 280 watts for the cruise module, 177 watts for the lander, and 45 watts for the Sojourner rover. An important consideration for satellite programs is the weight of the spacecraft. Currently, the power system typically takes up about a quarter of the total spacecraft mass budget while the solar array and support structure comprise about a third of the power system mass. Launch costs are estimated to be $11,000 per kilogram in low Earth orbit and $66,000 per kilogram in GEO. Hence, reducing spacecraft mass has a potential added benefit of lowering launch costs. Crystalline silicon and gallium-arsenide-based solar cells, currently employed in space solar PV power arrays, are rigid and fragile. Therefore, the PV arrays employ a honeycomb core with face sheets of aluminum or alternatively very lightweight Kevlar or graphite fibers. The PV array blanket is folded in an accordion style before placement in a canister. Deploying the array can pose problems. This happened in November 2000 with the large solar array on the International Space Station. Manufacturing costs for solar arrays are an important consideration for the total spacecraft budget. The array manufacturing costs for a mediumsized 5-kilowatt satellite can exceed $2 million. Current singlecrystal technology can cost more than $300 per watt at the array level and weigh more than 1 kilogram per square meter equivalent to a specific power of about 65 watts per kilogram.
Future Technologies
Future missions would include very large solar power satellites as well as very small satellites. Some long-term plans envision swarms of very small, distributed, autonomous satellites called microsats or even nanosats to perform specific tasks. In all these missions, reducing the total system cost would become increasingly more important. Highly efficient gallium arsenide-based multijunction cells, concentrator systems, and thin-film cells are being developed for the future space missions. Copperindium-gallium selenide-sulfide or amorphous hydrogenated silicon thin-film solar cells may be able to reduce both the manufacturing cost and the mass per unit power by an order of magnitude from the current levels. Moving to a thin-film technology could conservatively reduce array-manufacturing costs to less than $500,000 from the current cost of $2 million for a medium-sized 5-kilowatt satellite. For small satellites, increasing the solar array specific power from a current typical value of 65 watts per kilogram will allow for either an increase in payload power or payload mass, or both.
Weight benefits of higher efficiency cells are decreased and high costs become less affordable in the case of flexible thin-film blanket arrays that can be easily rolled out. Non rigid cells also have an advantage in stability. For example, flexible amorphous hydrogenated silicon solar arrays have continued to function after being pierced by tiny meteorites .