Professional Documents
Culture Documents
at the ends
at 1/4 from both ends Click here for answer 2. If the depth is kept constant for beam of uniform strength then its width will vary proportional to
Sqrt(M)
M^2
M^3 Click here for answer 3. When a beam deflects into a uniform strength then its width will vary proportional to
I/2R
I/8R
I^2 /8R
I^2 /2d Click here for answer 4. The longitudinal stress in a thin cylindrical shell is
Pd/4t
Pd/2t
Pt/4d
Pt/2d Click here for answer 5. The ratio of maximum shear stress and average shear stress for a rectangular section is
1.5
2.5
3 Click here for answer 6. A fixed beam of span L carries a central point load W. The maximum sagging bending moment in the beam is
WL/2
WL/4
WL/8
WL/16 Click here for answer 7. Air entrainment in the concrete increases
workability
strength
the unit weight Click here for answer 8. The relation between modulus of rupture Fcr and characteristic strength of concrete Fck is given by
Fcr = 1.2 S Fck Click here for answer 9. The compressive strength of 100 mm cube as compared to 150 mm cube is always
less
more
equal
may be any of the above Click here for answer 10. For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory
11. For bars in tension a standard hook has an anchorage value equivalent to a strength length of
12
16
24 Click here for answer 12. Cube strength of controlled concrete to be used for pre-tensioned and post-tensioned work respectively should not be less than
530 Kg/cm^2 and 420 Kg/cm^2 Click here for answer 13. The creep strains are
independent of loads Click here for answer 14. Ratio of compressive strength to tensile strength of concrete
remains constant
none of the above Click here for answer 15. In limit state design of concrete for flexure, the area of stress block is taken as
0.36 Fck Xu
0.42 Fck Xu
0.446 Fck Xu
0.53 Fck Xu Click here for answer 16. The fitness modulus of the fine aggregate is in the range of
2.0 to 3.5
3.5 to 5.0
5.0 to 7.0
6.0 to 8.5 Click here for answer 17. According to IS:456-1978, the maximum reinforcement in a column is
2%
4%
6%
8% Click here for answer 18. The minimum cover in a slab should neither be less than the diameter of bar nor less than
10 mm
15 mm
20 mm
13 mm Click here for answer 19. If the permissible stress in steel in tension is 140 N/mm^2, Permissible stress in concrete in bending compression is 5N / mm^2. Then the depth of neutral axis for a singly reinforced rectangular balanced section will be
0.35 d
0.40 d
0.45 d
dependent on grade of concrete also Click here for answer 20. The slab is designed as one way if the ratio of long span to short span is
less than 1
21. In any beam when the moment of inertia about the neutral axis is doubled, its deflection is
doubled
tripled
halved
minimum Click here for answer 22. The limits of percentage of the longitudinal reinforcement in a column is given by
0.15% to 2%
0.8% to 4%
0.8% to 6%
0.8% to 8% Click here for answer 23. A rigid prop provided for a beam
brings the shear force at the section to zero Click here for answer 24. In a simply supported beam AB with a concentrated load W at a distance 'a' from support A and 'b' from support B, the deflection under the load is
wa^2 / 3EI
wa^2 b + 2/EIL Click here for answer 25. For the design of retaining walls the minimum factor of safety against over-turning is taken as
1.5
2.0
2.5
3.0 Click here for answer 26. A cantilever beam is loaded by a point load at the free end. It is likely to fail by B.M.
at mid span
at support
none Click here for answer 27. The distance between centre lines of a broad gauge is 1.686m. The most economic length of sleeper for efficient distribution of B.M. is
1.866 m
2.866 m
3.866 m
0.866 m Click here for answer 28. In a simply supported beam of span L carrying an eccentric couple M acting at a distance A from the left support, the reaction included at the support is
M/L
L/M
ML
1/ML Click here for answer 29. Area of shear force diagram between two sections is
70 KNm
140 KNm
280 KNm
can not be found Click here for answer 30. The section modulus of square section of side A is
a^2 /6
a^3 /6
a^4 /12
31. The minimum percentage of mild steel reinforcement in walls of RCC water tanks of 450 mm thick is about
0.20
0.30
0.24