Professional Documents
Culture Documents
Back
Features
Wide range of sizes and congurations allows selection of optimal housing. Low weight to strength ratio.
For straight shaft, the bearings with tapered bore and adapter can be mounted at any selected shaft position. For stepped-shaft, the bearings with cylindrical bore are xed by shaft nut.
Remark: Housings not listed in the dimensions tables are also manufactured, consult NACHI for more information.
Table of contents
Type Symbol SN5 SN6 SN30 SN31 SN5F SN6F SN2 SN3 SN2C SN3C SN2F SN3F SN2FC SN3FC SD5 SD6 SD30 SD31 V Bore diameter on both sides Same Applicable Bearing Shaft Dia. (mm) 20140 20140 10170 00170 20140 20140 25160 25 85 25160 25 85 25160 25 85 25160 25 85 150300 150260 150300 150300 30200 35220 Page
SN Standard type
Tapered bore with adapter Tapered bore with adapter Cylindrical bore Cylindrical bore Cylindrical bore Cylindrical bore Tapered bore with adapter Tapered bore with adapter Cylindrical bore
page 545
page 553
Split type
page 559
page 565
SD Standard type
Same
page 571
Onepiece type
V Standard type
Same Difference
Remark: Please contact NACHI for housings not listed in table, special dimension, and with special accessories.
One-piece housings
V 215 D C 135 110
Type symbol: V Housing seating diameter
(Same as outside diameter of bearing)
Shaft diameter of small diameter side Numerical: Shaft diameter (mm) 0: End cover
Material symbol (None): Gray cast iron FC200 D : Spheroidal graphite iron castings FCD450 S : Carbon steel castings SC450 Cover symbol Shaft diameter of large diameter side Numerical: Shaft diameter (mm)
Remarks 1. When symbol are omitted, shift to left side. 2. Supplementary symbols accord with split housing. 3. Threads and number of oil inlet/outlet are shown in tables. 4.Grease nipple of button-head type is attached at grease inlet.
2. Designations
Split-housings
Type symbol SN: Standard type SD: Large type for heavy load Dimension series number
SN 2 20 D F2 C Supplementary symbol E NA P3 S0
Oil seal (None): GS seal(Standard) ZS : ZF seal SO : Without oil seal Drainage cap (None): Standard (one side except SD type) PD : Both sides P3 : PT3/8 threads for cap P4 : PT1/2 threads for cap Grease nipple (None): A type nipple (Standard) NB : B type nipple End cover (None): Without end cover E : Insert type EH : Bolt attach type EM : one-piece type
Remarks 1. When symbol are omitted, shift to left side. 2. Threads and number of grease inlet/outlet are shown in tables. 3. Grease nipple A type is attached at grease inlet.
SR 180 12.1 2
Locating ring symbol: SR Outside diameter (mm)
(Same as outside diameter of bearing)
Required number
5,6,30,31: Applied to Tapered bore bearing 2,3 : Applied to Cylindrical bore bearing Bore diameter number (Same as bore diameter number of applied bearing) Material symbol (None): Gray cast iron FC200 D : Spheroidal graphite iron castings FCD450 S : Carbon steel castings SC450 Bottom face symbol (None): Hollow bottom (Standard) F : Flat bottom (without bolt hole) F2 : Flat bottom (with 2 bolt holes) F4 : Flat bottom (with 4 bolt holes) Bore dia. on both sides (None): Same C : Difference
Width (mm)
Remark: The necessary number of locating rings is shown as X number or required locating rings immediately after the part number.
(3) Combination of Plummer Block Housing, Bearing, Adapter and Locating Ring
The designations of combination are obtained by adding each with + as following order.
S N 5 2 0 + 2 2 2 2 0 E X + H 3 2 0 X + S R 2 0 0 1 3 . 5
Plummer block housing
2
Number of locating ring
Bearing
Adapter
Reference
Unit: mm
Bearing type Housing type SN5 SN5F SN6 SN6F SN30 SN31 SN2 SN2F SN3 SN3F SD5 SD6 SD30 SD31 V 12
Self-aligning Ball Bearings 22 05K 22K 05 22 08(K) 22(K) 13 05K 22K 05 17 07(K) 22(K) 23 05K 22K 05 17 07(K) 22(K) 230 24K 38K 34K 64K 22(K) 44(K) 231 22K 38K 34K 64K
Spherical Roller Bearings 222 05K 32K 05 32 34K 64K 08(K) 38(K) 232 18K 32K 18 32 22(K) 38(K) 213 05K 22K 05 17 07(K) 22(K) 223 08K 32K 08 17 34K 56K 08(K) 32(K)
f2 d3 d2 d1
20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 190 200 210 220 230 240 250 260 270 280 300 320 340 360 380 400 410 430 450
+0.300 0
+0.300 0
+0.180 0
+0.350 0
+0.350 0
+0.400 0
+0.220 0
+0.400 0
+0.460 0
+0.460 0
+0.520 0
+0.520 0
+0.570 0
+0.270 0
+0.570 0
+0.630 0 +0.700 0
+0.630 0
4.2 5.4 5.4 5.4 5.4 5.4 6.9 6.9 6.9 6.8 8.1 8.1 8.1 8.1 9.3 9.3 10.8 10.8 10.7 10.7 10.7 12.2 12.2 12.2 13.7 13.7 13.7 13.7 13.7 13.7 13.7 13.7 13.7 13.7 15.5 15.5 15.5 15.5 17.3 17.3 17.3 19 19 19 19.8 19.8 19 19 20 19.8 19.8 20.3
22(K) 40(K)