You are on page 1of 43

GEAS COMPILATION

1. Date of approv al of RA 9292 a. April 14, 2004 c. April 17, 2004 b. April 14, 2007 d. None of these

2. There are ______ Articles and _____ sections in the RA 9292. a. 8,42 c. 7, 43 b. 8, 43 d. 7,42

3. Any person who shall v iolate any prov ision of RA 9292 or any rules, regulations, the Code of Ethics and the Code of Technical Standards of Practice is stated in section _________. a. 35 c. 37 b. 36 d. 38

4. This act is was consolidation of House Bill No. 5224 and Senate Bill No. 2683. a. RA 9292 c. RA 6541 b. RA 5734 d. None of these

5. The chairperson of the PRC shall include in the Commissions program the implementation of RA 9292, the funding of w/c shall be included in the Annual General Appropriation Act. a. Sec 39 c. Sec 41 b. Sec 40 d. Sec 42

6. According to section 43, RA 9292 shall take effect __________ following its full publication in the __________ or any newspaper of general circulation. a. 15 days, Law Gazette c. 15 days, internet b. 15 days, Official Gazette d. 30 days, internet

7. Who among the following persons was not a signatory of the 9292? a. FRANKLIN DRILON c. OSCAR G. YABES b. JOSE DE VENECIA JR d. JESUS P. NAZARENO

8. Section 40 of RA 9292. a. Appropriations c. Effectiv ity b. Repealing clause d. Separability clause

9. Which of the following is not true for the qualifications of Board Members of Electronics Engineering? a. Be a citizen and a resident of the Philippines for 5 consecutive yrs prior to his appointment b. Member of good standing of the APO c. Must not hav e been conv icted of an offense inv olv ing moral turpitude d. Be of good moral character and integrity

10. All records of the Board, including applications for the examination, administrativ e cases inv olv ing PECE, ECE and ECTs shall be kept by a. BECE c. PRC b. IECEP d. APO

11. The members of the Board shall hold office for a term of __________ from date of appointment or until their successors shall hav e been appointed and qualified and may be re-appointed once for another term. a. two years c. 3 years b. at least 3 years d. 5 years

12. Section 7 states that the Board is v ested with the authority to: Adopt an official __________ of the Board. a. logo c. Av atar b. icon d. Seal

13. The compensation and allowances of the Board is comparable to that being receiv ed by the Chairman and members of existing regulatory boards under the Commission as prov ided for in the __________. a. Civ il Serv ice c. RA 1992 b. DBM d. Gen Appropriations Act

14. Each member of the Board shall take the/a __________ prior to the assumption of office. a. panel interv iew from the Appointment committee b. board exam c. proper oath d. none of these

15. How much or what fine is required for any person who shall v iolate any prov ision or any rules, regulations, the Code of Ethics and the Code of Technical Standards of Practice promulgated under RA 9292? a. Not less than Php100,000.00 nor more than Php 1M or by imprisonment of not less than 6 months nor more than 6 year b. Php100,000.00 to Php 1M or 6 yrs imprisonment or both, in the discretion of the court c. Not less than Php100,000.00 nor more than Php 1M or by imprisonment of not less than 6 months nor more than 6 years, or both, in the discretion of the court d. none of these

16. The Board and the __________ shall correct and rate the licensure examination papers a. Commission c. IECEP b. APO d. none of these

17. According to section 2-Statement of Policy, the state shall therefore dev elop and nurture competent, v irtuous, productiv e, and __________ PECE, ECE, and ECTs a. God-fearing c. v ersatile b. religious d. well-rounded

18. Within __________ years after the effectiv ity of RA 9292, the Board shall issue Certificate of Registration and Professional Identification Cards without examination to all applicants for registration as Electronics Technicians who comply to all the requirements stated in section 20.

a. 3 (three) c. 7 (sev en) b. 5 (five) d. none of these 19. With reference to prob 22, all submittals/documents shall be accompanied by a certification from __________ registered PECEs v ouching for the integrity, technical capability and good moral character of the applicant. a. at least 3 c. 5 b. 3 d. none of these

GEAS (DLSU ECE LAWS AND ETHICS/physics)

2 2 3 3 4 4 20. The position x of an experimental rocket mov ing along a long rail is measured to be x(t) = (4m/s)t + (7m/s )t + (5m/s )t (0.35m/s )t ov er the first 10s of its motion, where t is in seconds and x is in meters. Find the v elocity of the rocket for the first 10 seconds. a. 43 m/s c. 244m/s b. 224 m/s d. 2240 m/s

SOLUTION: 2 3 2 4 3 v = dx/dt = (4m/s) + (14m/s )t + (15m/s )t (1.4m/s )t Substituting t = 10 s, giv es v = 244 m/s

21. Early in the nineteenth century, James Watt inv ented the steam engine. In order to conv ince people, who relied heav ily on horses for mechanical work, he demonstrated how useful his steam engine was by utilizing a horse that lifted water from a well ov er a certain period of time and called the corresponding power expended one horsepower. Assume that water has a mass density of 1.0 3 3 2 x 10 kg/m , that the well was 20m deep, and that the horse worked for 8 hours. How many liters of water did the horse raise from the well? Use the following constants: 1 hp = 746 Watts, g = 9.8 m/s . a. 1.1 x 10 2 3 L c. 1.1 x 10 L

5 b. 110 L d. 1.1 x 10 L

SOLUTION: The work done of the tension in lifting a mass of water is giv en by: W = m g Dy Where: W = work, m = mass = pV, Dy = distance, V = v olume, p= mass density,

P = work /time, Substituting all v alues, we get for V

V= 3 3 5 Since 1 m = 10 L, then V = 1.1 x 10 L.

22. As prov ided in ACT 3846, the construction of a radio station shall begin only when a. A personnel of NTC has conv eyed through telephone that the application has already been approv ed. b. the firm applying for the construction permit has

submitted to the NTC its application for the same. c. the technical documents has already been signed and sealed by the PECE. d. The NTC has already issued a Permit to construct.

23. As prov ided in RA7925, a VAS prov ider needs to secure a franchise if a. it is offered by a telecommunications entity whose proceeds of utility operations are not crosssubsidized. b. it does not discriminate other serv ice prov iders against rates. c. it is offered by a telecommunications entity that uses a separate book of accounts for VAS. d. it puts up its own network.

24. According to the code of ethics, if you are employed in a company and you wish to engage in a business which may compete with your company, the most ethical thing to do is to a. inform your employer about it b. hav e somebody run the business instead of you c. try to find new clients d. keep your prices lower than your companys

FEU(ENGG ECONOMY)

25. An inv estor has an option to purchase a tract of land that will be worth P20,000 in sev en years. If the v alue of the land increases at 9% each year, how much should the inv estor be willing to pay now for this property? a. P9,341 c. P11,521 b. P10,941 d. P12,015

SOLUTION

26. Suppose that you make 12 equal annual deposits of P2,000 each into a bank account paying 8% interest per year. The first deposit will be made one year from today. How much money can be withdrawn from this bank account th immediately after the 12 deposit? a. P35,492 c. 37,954 b. P36,21 d. P38,755

SOLUTION

27. What is the effectiv e rate of interest if P1000 is inv ested at a nominal rate of 15% compounded quarterly? a. 15.86% c. 17.86% b. 16.86% d. 18.86%

SOLUTION

28. A man purchased a house for P425,000. In the first month that he owned the house, he spent P75,000 on repairs and remodeling. Immediately after the house was remodeled, he was offered P545,000 to sell the house. After some consideration, he decided to keep the house and hav e it rented for P4,500 per month starting two months after the purchase. He collected rent for 15 months and then sold the house for P600,000. if the interest rate was 1.5% per month, how much extra money did he make or lose by not selling the house immediately after it was remodeled? a. P3,000 c. P5,000 b.P4,000 d. P6,000

SOLUTION

29. On the day his grandson was born, a man deposited to a trust company a sufficient amount of money so that the boy could receiv e fiv e annual payments of P20,000 each th for his college tuition fees, starting with his 18 birthday. Interest at the rate of 12$ per annum was to be paid on all amounts on deposit. There was also a prov ision that the grandson could elect to withdraw no annual payments th and receiv e a single lump amount on his 25 birthday. The grandson chose this option. How much did the grandfather deposit? a. P9,500 c. P11,500 b. P10,500 d. P12,500

SOLUTION

30. A man bought an equipment costing P30,000 payable in 12 quarterly payments, each installment payable at the beginning of each period. The rate of interest is 24% compounded quarterly. What is the amount of each payment a. P1,700 c. P3,700 b. P2,700 d. P4,700

SOLUTION

31. A telecommunication company purchased an equipment for P53,000 and paid P1,500 for freight and deliv ery charges to the job site. The equipment has a normal life of 10 years with a trade-in v alue of P5,000 against the purchase of a new equipment at the end of the life. Determine the annual depreciation cost by the sinking fund method. Assume interest at 6.5% compounded annually.

a. P2,543 c. P4,215 b. P3,668 d. P5,956

SOLUTION

32. A plant bought a machine for P200,000 and used it for 10 years, the life span of the equipment. What is the book v alue of the machine after 5 years of use? Assume a scrap v alue of P20,000. Use double declining balance method. a. P43,648 c. P65,536 b. P59,425 d. P70,923 SOLUTION

GEAS(ADU ENGG MANAGEMENT)

33. It is a method of managing all the activ ities that affect the quality of goods or serv ices in order to prev ent faults a. Quality Assurance b. Quality Circle c. Quality Control d. Quality Standard

34. This type of business organization can be set up without any formality. It exist when there are a number of people inv olv ed who are part owners of the business. a. Association b. Corporation c. Partnership d. Sole Proprietorship 35. Items purchased from a v endor cost Php 20 each, and the forecast for next years demand is 1,000 units. If it costs Php 5 ev ery time an order is placed for more units and the storage cost is Php 4 per unit per year, what quantity should be order each time? a. 20 b. 30 c. 40 d. 50

SOLUTION Q = (2DS/H) = ((2(1000)(5))/4) = 50 units

36. Two products, X and Y, both require processing time on machines I and II. Machine I has 200 hours av ailable, and machine II has 400 hours av ailable. Product X requires one hour on machine I and four hours on machine II. Product Y requires one hour on machine I and one hour on machine II. Each unit of product X yields PhP 10 profit and each units of Y yields PhP 5 profit. What is the Linear Programming Model for this problem.

a. Max Profit = PhP 5X + PhP 5Y Subject to: X + Y 200 X + Y 400 X,Y0 b. Max Profit = PhP 10X +PhP 5Y Subject to: X + Y 200 4X + Y 400 X,Y0

37. This process can be used to measure achiev ement in Total Quality Management (TQM) system. Also it prov ides the essential control and measure feedback loop necessary for quality improv ement a. Benchmarking c. Quality chain b. Continuous Improv ement d. Quality circle

38. It is the process of attracting potential employees to the company so that the selection process can be carried out. a. Adv ertising b. Benchmarking

c. Selection d. Recruitement

39. It is the name giv en to any activ ity undertaken by the organization with the express purpose of gaining information about potential customer a. Market Analysis b. Market Intelligence c. Market Research d. Market System

40. It is used when product are made singly or in small batches. It happens when a small number of products are processed at each storage before going on to the next stage. a. Batch Production b. Flow Production c. Job Production d. Production Design

41. It inv olv es a v oluntary association of people, called members, who operate an enterprise collectiv ely. The aim of this organization is not to make profit but to giv e support to their members. a. Association b. Cooperatives c. Priv ate Companies d. Public Companies

42. It is the rational way to ensure that our limited time is always used effectiv ely. a. Management Commitment b. Management Responsibility c. Time Management d. Time Conflict

GEAS (UST ENGG MATERIALS)

43. These materials are hard and brittle, insulativ e to electricity and heat, and v ery resistant to high temperatures and harsh env ironments. a. polymers b. metals c. ceramics d. semiconductors

44. These materials hav e a large number of non-localized electrons, as an effect are v ery good conductors of electricity and heat. They are strong yet deformable, and extensiv ely used in structural applications a. ceramics b. composities c. semiconductors d. metals

45. Materials composed of more than one material type and are designed to display a combination of the best characteristics of each component material. a. polymers b. ceramics c. metals d. composites

46. A material whose atomic arrangement occurs as periodic, repeating structures ov er large distances. a. crystalline b. polycrystalline c. solid d. amorphous

47. An elemental solid hav ing a different crystal structure, usually due to the prev ailing temperature and pressure. a. amorphous b. polymorph c. crysallite d. allotrope

48. This metal is alloyed with steel to giv e it corrosion resistance properties, resulting in stainless steel. a. v anadium b. molybdenum c. chromium d. magnesium

49. This element is used in modern, super strong permanent magnets because of their high coerciv ities. a. beryllium b. Neodymium c. yttrium d. alnico

50. The deterioration of an engineered material due to interaction with div erse env ironments which lead to the degradation of its material properties a. corrosion b. disintegration c. oxidation d. dissolution

GEAS (UDM THERMODYNAMICS)

51. The property of a substance which remains constant if no heat enters or leav es the system, while it does work or alters its v olume, but which increases or diminishes should a small amount of heat enter or leav e. a.Internal energy b. system c. entropy d. Enthalpy

52. The quantity of heat required to change the temperature of unit mass through one degree. a. Temperature b. Specific Heat c. Thermal Equilibrium d. Calorie

53. If the temperature of a giv en quantity of gas is held constant, the v olume of the gas v aries inv ersely with the absolute pressure during a change of state a.General Gas Laws b. Joules Law c. Charles Law d. Boyles Law

54. An internally rev ersible process of a substance during which the pressure remains constant. a.isometric b.isothermal c.adiabatic d.isobaric

55. The energy stored in a substance by v irtue of the activ ity and configuration of its molecules and of the v ibration of the atoms within the molecules. a.Internal Energy b .Heat c. Enthalpy d.Entropy

56. When two bodies, isolated from other env ironment, are in thermal equilibrium with a third body, the two are in thermal equilibrium with each other is a statement of.. st nd a.1 Law of Thermodynamics c.2 Law of Thermodynamic b. Zeroth Law d. Maxwells Theory of Thermal Equilbrium

57. Not all energy receiv ed as heat by a heat-engine cycle can be conv erted into mechanical work, some are also rejected is a statement of. st a.1 Law of Thermodynamic s b.Zeroth Law nd c. 2 Law of Thermodynamics d.Law of Conserv ation of Energy

58. The combined mass of car and passengers trav elling at 72 km/hr is 1500kg. Find the kinetic energy of this combined mass. a.300kJ b.330kJ c.305kJ d. 310kJ

SOLUTION

2 2 2 K=mv = (1500kg)(72km/hr) (1000m/km) 2 2 2k (2)(1kg-m/N-sec )(3000 sec/hr) = 300,000 J or 300 kJ

2 59. A mass of 5kg is 100m abov e a giv en datum where local g=9.75 m/sec . Find the grav itational force in newtons and the potential energy of the mass w/ respect to the datum. a.49.25 N,4925 J b.52.05 N,5205 J c.48.75 N,4875 J d.47.85 N,4785 J

SOLUTION 2 P = mg z = (5kg)(9.75m/sec )(100m = 4875 J 2 k (1kg-m/N-sec )

Fg = mg = 5(9.75) = 48.75 N k1

60. A pressure gage register 50 psig in a region where the barometer is 14.25 psia. Find the absolute pressure in Pa. a.453 kPa b.434 kPa c.435 kPa d.443 kPa

SOLUTION

P = P atm + P g = 14.25 + 50 = 64.25 psia P = (64.25psia)(6894.8Pa/psi) = 443 kPa

61. During an isentropic process of 1.36 kg/sec of air, the temperature increases from 4.44 C to 115.6C. if Cp =1.0062kNm for a non-flow process, what is H? kgK a.152.2 kg/s b.152.2 J/s c.152.2 kJ/s d.152.2 Btu/s

SOLUTION

H = mCp T = 1.36kg/s(1.0062kNm/kgK)(388.75-277.59K) = 152. kJ/s

62. This Law States that The quantity of the substance entering the system is equal to the substance leav ing the system st a.1 Law of Thermodynamics b.Law of Conservation of Mass nd c.Newtons 2 Law of Motion d.Law of Conserv ation of Energy

63. if the pressure of a giv en quantity of gas is held constant, the v olume of the gas v aries directly with the absolute temperature a. General Gas Law b. Boyles Law c. Charles Law d. Joules Law

64. The Acceleration of a particular body is directly proportional to the resultant force acting on it and inv ersely proportional to its mass is a statement of st a. Joules Law b. 1 Law of Thermodynamics nd c. Newtons 2 Law of Motion d. Boyles Law

65. Energy is neither created nor destroyed, but is conv erted from one form to another st a. 1 Law of Thermodynamics nd b. Newtons 2 Law of Motion nd c. 2 Law of Thermodynamics d. Law of Conserv ation of Mass

FEU( GEAS STRENGTH)

66. It occurs when a cutting action is applied as you would see with scissors, tin snips, or punches. a. Direct shear c. Torsional shear b. Bending stress d. Torsional stress

67. It occurs when a member carries a load perpendicular to its long axis while being supported in a stable manner.

a.

Direct shear c. Torsional shear b. Bending stress d. Torsional stress.

68. It is the internal resistance offered by a unit area of the material from which a member from which a member is made to an externally applied load.

a. stress b. strain c. moment d. Torque

69. A certain support stand design to carry downward loads. Compute the stress in the square shaft at the upper part of the stand for a load of 27,000 lb. The line of action of the applied of the applied load is centered on the axis on the shaft, and the load is applied through a thick plate that distributes the force to the entire cross section of the stand. a. 10,000psI b. 11,000psi c. 12,000psi d. 13,000psi

70. The proportional limit is the v alue of stress on the stress-strain diagram curv e at which the curv e first dev iates from a straight line.

a. b. c. d.

Proportional limit Elastic limit Yield point Tensile point

71. It is the v alue of stress on the stress-strain curv e at which the material has deformed plastically; that is, it will no longer return to its original size and shape after remov ing the load.

a. b. c. d.

Proportional limit Elastic limit Yield point Tensile point

72. It is the v alue of stress on the stress-strain curv e at which there is a significant increase in strain with little or no increase in stress.

a. b. c. d.

Proportional limit Elastic limit Yield point Tensile point

73. It is the highest v alue of apparent stress on the stress-strain curv e.

a. b. c. d.

Proportional limit Elastic limit Yield point Tensile point

74. It is a measure of the stiffness of a material determined by the slope of the straight-line portion of the stress-strain curv e

a. b. c. d.

Modulus of elasticity Modulus of rigidity Strain Stress

75. A ductile material is one that can be stretched, formed, or drawn to a significant degree before fracture. A metal that exhibits a percent elongation greater than ____ % is considered to be ductile. a. 2 b. 3 c. 4 d. 5

76. A brittle material is one that fails suddenly under load with little or no plastic deformation. A metal that exhibits a percent elongation ____ 5.0% is considered to be brittle. a. equal b. Greater than c. Less than d. It depends on the room temperature

77. The ratio of shearing stress to shearing strain is called:

a. b. c. d.

Modulus of elasticity Modulus of rigidity Modulus of elongation Modulus of stressibility

78. It is the ability of a material to absorbed applied energy without failure a. Ductility b. Brittleness c. Hardness d. Toughness

79. It is the indication of the resistance of a material to indentation by a penetrator. a. Ductility b. Brittleness c. Hardness d. Toughness

80. It is a measure of pulling and pushing force

a. b. c. d.

Axial force Shear force Torque Bending moments

81. It is the measure of the total resistance to sliding.

a. b. c. d.

Axial force Shear force Torque Bending moments

82. It is the measure of the resistance to twisting.

a. b. c. d.

Axial force Shear force Torque Bending moments

2 83. A common bar suspended from certain support has axial load of 10kN. If the bar has a cross section of 20mm , find the stress experience by the bar. a. 350MPa b. 420MPa c. 485MPa d. 500MPa

84. Assume that a 25-mm diameter riv et joins the plates that are each 125 mm wide. The allowable stresses are 130 MPa for bearing in the plate material and 65 MPa for shearing of the riv et. Determine the minimum thickness of each plate. a. 10MPa b. 20MPa c. 30MPa d. 40Mpa

85. A cylinder pressure v essel is fabricated from plates which hav e a thickness of 20mm. The diameter of the pressure v essel is 450 mm and its length is 3.5m. Determine the maximum internal pressure which can be applied if the stress in the steel is limited to 150MPa.

a. 15.33MPa b. 16.67MPa c. 17.53MPa d. 18.83MPa

86. The wall thickness of a 3ft-diameter spherical tank is 4/17 in. Calculate the allowable internal pressure if the stress is limited to 9000 psi. a. 155.47psi b. 169.25psi c. 176.47psi d. 188.73psi

87. A steel bar 40mm in diameter and 3m long is surrounded by a shell of cast iron 6mm thick. Compute the load that will compress the combined bar a total of 0.95 mm in the length of 2m. For steel E=300GPa, and for cast iron, E=150GPa. a. 151kN b. 161kN c. 171kN d. 181kN

2 88. A steel rod 3.5m long is secured between two walls. If the load on the rod is zero at 30C, compute the stress when the temperature drops to -30C. The cross sectional area of the rod is 1200mm , =11.7um/(mC), and E=200Gpa a. 110MPa b. 120MPa c. 130MPa d. 140Mpa

6 89. A steel shaft 3ft long that has a diameter of 5in is subjected to a torque of 14kip-ft. Determine the maximum shearing stress. G=12x10 psi. a. 0.47 b. 0.53 c. 0.68 d. 0.71

90. What is the minimum diameter of a solid steel shaft that will not twist through more than 4 in a 6m length when subjected to a torque of 13kN-m? What max shearing stress is dev eloped? G=85 Gpa a. 107.6mm b. 113.3mm c. 121.9mm d. 126.4mm

91. Determine the elongation in a helical steel spring composed of 20 turns of 20-mm diameter wire on a mean radius of 90 mm when the spring is supporting a load of 2.5kN. Use G=83 Gpa a. 160mm b. 165mm c. 170mm d. 175mm

FEU(GEAS THERMODYNAMICS)

92. It is the transfer of energy from the more energetic particles of substance to the adjacent less energetic ones as a result of interactions between the particles.

a. b.

Conduction c. Conv ection Radiation d. Absorption

93. It indicates that the rate of heat conduction in a direction is proportional to the temperature gradient in that direction.

a. b. c. d.

Fouriers Law of Heat Conduction Fouriers Law of Heat Conv ection Fouriers Law of Heat Radiation Fouriers Law of Heat Absorption

94. Which of the following is considered the best conductor of heat? a. Gold b. Copper c. Silv er d. Diamond

95. It is the mode of energy transfer between a solid surface and the adjacent liquid or gas that is in motion, and it inv olv es the combined effect conduction and fluid motion. a. Conduction c. Convection b. Radiation d. Absorption

96. It is the energy emitted by the matter in the form of electromagnetic wav es as a result of the changes in the electronic configurations of the atom or molecules.

a.

Conduction c. Conv ection

b.Radiation d. Absorption

97. It states that energy can neither be destroyed nor created; it can only change forms.

a. b. c. d.

First law of thermodynamics Second law of thermodynamics Third law of thermodynamics Zeroth law of thermodynamics

98. In second law of thermodynamic, which of the following state that no heat engine can hav e a thermal efficiency of 100% or as far as power plant to operate, the working fluid must exchange heat with the env ironment as well as the furnace.

a. b. c. d.

Kelvin Plank Statement Clausius-Plank Statement Clausius Statement Kelv in Statement

99. In second law of thermodynamic, which of the following state that no dev ice can transfer heat from cooler body to a warmer one without leav ing an effect on the surroundings.

a. b. c. d.

Kelv in Plank Statement Clausius-Plank Statement Clausius Statement Kelv in Statement

100. It is defined as the amount of light output in lumens per W of electricity consumed.

a. b.

Light intensity c. Light efficacy Light efficiency d. Light luminosity

101. Carnot cycle is composed of how many rev ersible processes? a. 1 b. 2 c. 3 d. 4

102. Which of the following processes are inv olv ed in carnot cycle?

a. b. c. d.

Two isothermal ; two isobaric One isothermal; three adiabatic Three isobaric; one adiabatic Two adiabatic ; two isothermal

103. State that the thermal efficiencies of all rev ersible heat engines operating between the same two reserv oirs are the same, and that no heat engine is more efficient than a rev ersible one operating between the same two reserv oirs.

a. b. c. d.

Throttle principle Otto principle Carnot principle Kelv in principle

104. A carnot heat engine receiv es 500KJ of heat per cycle from a high-temperature source at 600 C and rejects heat a low temperature sink at 40C. Determine the thermal efficiency of this Carnot engine. a. 93.33% b. 6.67% c. 35.85% d. 64.15%

105. A piston cylinder dev ice contains a liquid-v apor mixture of water at 400K. During a constant pressure process, 700 KJ of heat is transferred to the water. As a result, part of the liquid in the cylinder v aporizes. Determine the entropy change of the water during this process. a. 1.75kJ/K b. 280kJ-K c. 7000kJ d. 0.57K/kJ

106. Which of the following equation of state has two constants?

a. b. c. d.

Vander Waals Equation Beattie-Bridgeman Equation Benedict-Webb-Rubin Equation Strobridge Equation

107. How many constant are there in Strobridge Equation of State? a.13 b. 14 c. 15 d. 16

108. Which of the following equation of state has eight constant?

a. b. c. d.

Vander Waals Equation Beattie-Bridgeman Equation Benedict-Webb-Rubin Equation Strobridge Equation

109. Consider a person standing in a breezy room at 22C. Determine the total rate of heat transfer from this person if the exposed surface area and the av erage outer surface temperature of the person 2 2 -8 4 4 are 1.2 m and 33C, respectiv ely, and the conv ection heat transfer coefficient is 6 W/m .=0.95 and =5.67x10 W/m -K a.120.5J/s b. 135.7J/s c. 143.2J/s d. 151.9J/s

3 3 110. A piston cylinder dev ice initially contains 0.8 m of air at 110kPa and 80C. The air is now compressed to 0.2 m in such a way that the temperature inside the cylinder remains constant. Determine the work done during this process. a.-122kJ b. -123kJ c. -124kJ d. -125kJ

111. It is the energy possesses by the system as a result of its elev ation with respect to the grav itational acceleration of the earth. a. Potential b.Kinetic c. Momentum d.Impulse

112. It states that if two bodies are in thermal equilibrium with a third body, they are also in thermal equilibrium with each other

a. b. c. d.

First law of thermodynamics Second law of thermodynamics Third law of thermodynamics Zeroth law of thermodynamics

113. Determine the mass of the air in a room whose dimensions are (5x6x7) cm at 105 kPa and 27C.

114. Heat is transferred to a heat engine from a furnace at a rate of 92MW. If the rate of waste heat rejection to a nearby riv er is 45MW, determine the net power output and the thermal efficiency for this heat engine. a.48.91% b. 51.09% c. 32.84% d. 67.15%

115. The food compartment of a refrigerator is maintained at 4C by remov ing heat from it at a rate of 300 KJ/min. If the required power input to the refrigerator is 3KW, determine the coefficient of performance of the refrigerator. a.1.67 b. 2.33 c. 3.67 d. 4. 12

3 116. A 50 kg iron block at 80C is dropped into an insulated tank that contains 0.5 m of liquid water at 25C. Determine the temperature when thermal equilibrium reached. The specific heat of iron is 0.45kJ/kg-C and for water is 4.18kJ/kg-C. a.20. 7C b. 25.6C c. 30.1C d. 35.6C

117. A rigid tank contains a hot fluid that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 850kJ. During the cooling process, the fluid loses 550kJ of heat, and the paddle wheel does 200kJ of work on the fluid. Determine the final energy of the fluid. Neglect the energy stored in the paddle wheel. a.500kJ b. 550 kJ c. 600kJ d. 650 kJ

3 118. Three moles of an ideal gas are compressed slowly and isothermally from a v olume of 5 to 1.5 ft , at a temperature of 320K. How much work is done? a.-8.12kJ b. -9.61kJ c. -10.44kJ d. -11.59kJ

2 2 119. A 4-in wall of fire brick, k=9 Btu/(ft -hr-F/in), has one surface at 300F, the other at 90F. Find the heat conducted through the area of 2ft in 1 day. a.22, 680Btu b. 19, 650Btu c. 15,510Btu d. 10,730Btu

120. If 80 g of iron shot at 100C is dropped into 200 g of water at 20C contained in an iron v essel of mass 50 g, find the resulting temperature. a.20.1C b. 21.8C c. 22. 3C d. 24.6C

121. When a 2lb of brass at 212F is dropped into 5lb of water at 35F, the resulting temperature is 41.2F. Find the specific heat of brass in Btu/lb-F. a.1.120 b. 0.091 c. 0.321 d. 1.233

122. How much heat is necessary to raise the temperature of 0.80 kg of ethyl alcohol from 15C of its boiling point 78.3C? a.10kcal b. 20kcal c. 30kcal d. 40kcal

3 3 123. The weight-density of air at 32F and 29.92 in Hg pressure is 0.081 lb/ft . What is its weight-density, in lb/ft , at an altitude where the pressure is 13.73 in Hg and the temperature is -40F? a.0.044 b. 0.055 c. 0.066 d. 0.77

TUP(GEAS PHYSICS)

124. Suppose that energy Q is required to accelerate a car from rest to v, neglecting friction. How much added energy would be required to increase the speed from v to 2v? a.Q b.2Q c. 3Q d.4Q

Using the energy equation W=KE2 KE1 2 Q = 0.5mv 0 - condition 1 2 2 W = 0.5m(2v ) 0.5mv - condition 2 2 2 2 W=2mv 0.5mv = 3(0.5mv ) = 3Q

3 125. Suppose you want to store 1.00 J of electric potential energy in a v olume of 1.00 m in v acuum. What is the magnitude of the required electric field? a. 0.475 MV/m b. 0.336MV/m c. 0.225TV/m d. 0.113TV/m

3 3 u=1.00J/1.00m = 1.00J/m E=2uo=2(1.00)o E=0.475 MV/m (a)

o 126. Material a is a water and material b is a glass with index of refraction 1.52. If the incident ray makes an angle of 60 with the normal, find the direction of the reflected ray. o o o o a.49.3 b. 91.3 c. 60 d. 34.7

According to law of reflection, r=a, hence if a=60o then r=60o (c) 127. The wav elength of the red light from a helium-neon sensor is 633 nm in air but 474 nm in the aqueous humor inside our eyeballs. Calculate the speed of light in this substance. 8 8 a. 2.25 x 10 m/s b. 3.25 x 10 m/s 8 8 c. 3.00 x 10 m/s d. 1.25 x 10 m/s Calculating the index of refraction, we hav e: n=o=633474=1.335 For the v elocity of light in this index we hav e:

v =c n=3.00x108m/s 1.335=2.247x108ms 2.25x108m/s (a)

128. A spaceship mov ing away from Earth with speed of 0.900c fires a robot space probe in the same direction as its motion, with speed of 0.700c relativ e to the spaceship. What is the probes v elocity relativ e to the Earth? a.0.900c b. 0.345c c. 0.700c d. 0.982c

vr=va+vb1+vavbc2 vr=0.900c+0.700c1+0.90.7c2c2=0.982c (d)

129. In optics, this effect refers to the blurring of the image produced on a concav e mirror due to the conv ergence of rays far from the mirror to other points on the principal axis. What do you call this effect? a.spherical aberration b. focal div ergence c. parallax error d. Snells effect

130. In fluid mechanics, this shows that the pressure of a fluid decreases as the speed of the fluid increases. In addition, the pressure of a fluid decreases as the elev ation increases. a.Clairuts equation b. Bernoullis equation c. Maxwells equation d. Hyrdofluid equation

131. In electrodynamics, what term refers to the av erage speed of the charge carriers? a. drag v elocity b. molecular-kinetic speed c. drift speed d. charge v elocity

-4 132. In electromagnetics and wav e theory, what refers to wav es, commonly generated by electronic dev ices, whose wav elengths ranges from approximately 0.3m to 10 m. Due to their short wav elengths these are often used in radar systems and for studying the atomic and molecular properties of matter. a.Radio wav es b. Microwaves c. AM wav es d. Radar wav es

ADU(GEAS STRENGTH OF MATERIALS)

133. A hole is to be punched out of plate hav ing a shearing strength of 40 ksi. The compressiv e stress in the punch is limited to 50 ksi. Compute the maximum thickness of plate from which a hole 2.5 inches in diameter can be punched. a. 0.500 in b. 0.781 in c. 0.102 in d. 0.204 in

t = 2.5(50) / 4(40) = 0.781 inches

134. A hole is to be punched out of plate hav ing a shearing strength of 40 ksi. The compressiv e stress in the punch is limited to 50 ksi. If the plate is 0.25 inches thick, determine the diameter of the smallest hole that can be punched a. 0.800 in b. 0.871 in c. 0.435 in d. 0.600 in

D = 4(0.25)(40) / 50 = 0.800 inches

135. A large pipe, called a penstock in hydraulic work, is 1.5 m in diameter. It is composed of wooden stav es bound together by steel hoops, each 300 sq. Millimetre in cross-sectional area, and is used to conduct water from a reserv oir to power a house. If the maximum tensile stress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30 m? a. 17.7mm b. 77.1 mm c. 177 mm d. 71.7 mm (1000)(9.81)(30)(1.5)L = 2(300x10^-6)(130x10^6)

L = 177 mm

136. At what angular v elocity will the stress in a rotating steel ring equal to 150 MPa if its mean radius is 220 mm? The density of the steel is 7.85 Mg/m^3. a. 19.87 rad/s b. 159 rad/s c. 138.2 rad/s d. 628 rad/s

= (1/0.22)(150x10^6 / 7850)^(1/2) = 628 rad/s

137. A pipe carry steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate use to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 80 MPa, of which 55 MPa is the initial stress? a. 14 b. 15 c. 16 d. 17

N = (3.5x10^6)(0.45 2x0.01)^2 / [(0.04^2)(8855)x10^6] = 16.18 round up N = 17

138. A pipe carry steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate use to cap the end. What circumferential stress is dev eloped in the pipe? a. 75.3 MPa b. 37.65 MPa c. 78.75 MPa d. 39.38 MPa

= (3.5)(450 2x10) / [2(10)] = 75.3 MPa

139. It is the maximum safe stress that a material can carry a. working stress b. Ultimate stress c. rupture strength d. Yield strength

140. It is the point at which there is an appreciable elongation of the material without any corresponding increase of load a. Elastic limit b. Yield point c. Ultimate stress d. Point of rupture

141. This component measures the pulling (or pushing) action perpendicular to the section a. Torque b. Bending moment c. Axial forces d. Shearing force

142. A steel rod hav ing a cross-sectional area of 300 sq. Meters and a length of 150 m is suspended v ertically from one end. It supports a tensile load of 20 kN at the lower end. If the unit mass of steel is 7850 kg/m^3 and E = 200x10^3 MN/m^2, find the total elongation of the rod. a. 54.3 mm b. 40 mm c. 43.3 mm d. 35 mm

= [(7850)(9.8)(150^2) / 2(200X10^9)] + [(20000)(150)(1000^2) / 300(200X10^9)] = 54.3 mm

143. What is the theoretical maximum v alue of Poissons ratio of any giv en material subjected to a uniform triaxial stress a. 0 b. 1 c. 1/3 d.

144. A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of cast iron 5 mm thick. Compute the load that will compress the combined bar a total of 0.8 mm in the length of 2m. For steel E = 200 GPa, and for cast iron E = 100 Gpa a. 291 kN b. 240 kN c. 192 kN d. 420 kN

P = [(/4)(0.05^2)(200x10^9)(0.0008)/2] + [(/4)(0.06^2 -0.05^2)(100x10^9)(0.0008)/2]

P = 192 kN 145. A solid steel shaft 5 m long is stressed to 80 MPa when twisted through 4 degrees. Using G = 83 GPa, compute the shaft diameter. a. 104 mm b. 138 mm c. 148 mm d. 160 mm

r = (80)(5) / [(4)(/180)(83000)] = 69 mm d = 2(69) = 138 mm

146. A solid steel shaft is not to twist through more than 3 degrees in a 6 m length when subjected to a torque of 12 kN.m. What maximum shearing stress is dev eloped? Use G=83GPa. a. 41.3 MPa b. 43.4 MPa c. 34.3 MPa d. 17.6 MPa

(/4)d^4 = (12000)(6) / [(3)(/180)(83x10^9)] d = 114 mm

= 16(12000) / [(.114)^3] = 41.3 Mpa

147. What is the minimum diameter of a solid steel shaft that will not twist through more than 3 degrees in a 6 m length when subjected to a torque of 12 kN.m? Use G=83GPa. a. 114 mm b. 116 mm c. 118 mm d. 120 mm

(/4)d^4 = (12000)(6) / [(3)(/180)(83x10^9)] d = 114 mm

148. A steel rod 2.5 m long is secured between two walls. If the load on the rod is zero at 20 degree Celsius, compute the stress when the temperature drops to -20 degrees Celsius. The cross-sectional are if the rod is 1200 sq. mm, coefficient of linear expansion = 11.7 um/(m-deg.C), and E = 200 GPa. Assume that the walls are rigid. a. 69.3 MPa b. 96.3 MPa c. 93.6 MPa d. 69.3 MPa

= (200x10^9)(11.7x10^-6)(20 - -20) = 93.6x10^6 Pa = 93.6 MPa

149. Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20 mm-diamter wire on a mean radius of 80 mm when tha spring is supporting a load of 2 kN. Use G = 83 GPa. a. 110.6 MPa b. 112.3 MPa c. 120.6 MPa d. 134.6 MPa

m = 80/10 = 8

= [16(2000)(0.08) / (0.02)^3] x{[4(8)-1] /[4(8)-4] + (0.615/8)} = 120.6 Mpa

150. Determine the elongation in a helical steel spring composed of 20 turns of 20 mm-diamter wire on a mean radius of 80 mm when tha spring is supporting a load of 2 kN. Use G = 83 GPa. a. 87.9 mm b. 78.9 mm c. 98.7 mm d. 89.7 mm

= 64(2000)(0.08^3)(20) / [(83x10^9)(0.02^4)] = 98.7 mm

151. These are components of the total resistance to sliding the portion to one side of the exploratory section past the other. a. Torque b. Bending moment

c. Axial forces d. Shear forces

152. Who first postulated that stress is proportional to strain in 1678? a. Thomas Young b. Robert Hooke c. Andrew Pytel d. Charles Augustus

MIT(GEAS CHEMISTRY)

153. How many zeroes in the measurement 0.00020040 are significant? a. three b. four c. six d. sev en

154. Which of the following describes a chemical change?

a. b. c. d.

Water boiling to form steam Sugar dissolv ing in a cup of coffee Hamburger grease solidifying on a plate Tarnishing silver

155. A homogenous mixture can be separated by all of the following methods except

a. b. c. d.

Filtration Chromatography Crystallization Distillation

156. Which of the following is not a pure substance?

a. b. c. d.

Hydrogen Oxygen Water Milk

157. A laboratory experiment was performed to determine the percent by mass of water in a hydrate. The accepted v alue is 36.0% water whose observ ed v alue has an error of 5.00%. Find the percent by mass of water. a. 31.0% water b. 36.0% water c. 37.8% water d. 41.0% water

36% * 1.05 =37.8%

158. Which of the following phase changes represent sublimation?

a. b. c. d.

Solid gas Gas solid Solid liquid Gas liquid

159. The amount of energy needed to change a giv en mass of ice to water at constant temperature is called the heat of

a. b. c. d.

Fusion Formation Condensation Crystallization

160. Which of the following is a binary compound?

a. b. c. d.

Hydrochloric acid Oxygen Citric acid Sodium chlorate

161. An example of a ternary compound is

a. b. c. d.

Potassium chlorate Ammonia Silv er chloride Sodium bromide

162. What is the charge of a hydrogen atom? a. 1+ b. 1- c. 2+ d.

163. The impossibility of knowing both the precise location and v elocity of subatomic particle at the same time is known as the a. Diffraction principle b. Probability principle c. Limiting principle d. Uncertainty principle

164. An atom which has the greatest ability to attract electron

a. b. c. d.

Oxygen Nitrogen Sulfur Bromine

165. If the v olume of the mole of gas molecules remains constant, lowering the temperature will make the pressure

a. b. c. d.

Increase Decrease Increase then decrease Decrease then increase

166. Whenev er you hav e equal v olumes of gases at the same temperature and pressure, the v olume must

a. b. c. d.

Contain equal number of particles Contain 2.4 milliliters of STP Contain one mole of any gas at STP Contain the Av ogadros number

167. What pressure must be applied to 225mL of gas at 1atm to reduce its v olume to 100mL? a. 0.44atm b. 2.25atm c. 22500atm d. 1710atm

P 1V1=P 2V2

168. How many moles of O2are present in 44.8L of O2 at STP? a. 1.2moles b. 1.4moles c. 2.0moles d. 2.8moles

169. At STP, 1 mole will occupy 22.4L

170. The properties of solution include all of the following except that a. It is homogeneous mixture if it has been well stirred b. Dissolved particles will settle out upon stirring c. It is clear and transparent with particles too small to be seen d. Dissolv ed particles will pass through a piece of filter paper

You might also like