Professional Documents
Culture Documents
onitoring the moisture in the raw materials, controlling the water addition during the mixing/blending process and finally checking the moisture of the materials in pelletised form, not only ensure an end product with
consistent quality, but will enable substantial savings to be achieved in the production process.
Hydronix, who originally pioneered the use of the microwave measurement technique for the concrete industry, have developed a range of digital microwave sensors that are particularly well suited to measuring in animal feed materials. In selecting a moisture sensor or system then there are five important criteria to be considered: The physical aspects of the measurement technique are inherently accurate and suitable for process and materials concerned The design of the sensors should enable them to be installed at the appropriate positions where it is necessary to measure the moisture. The ease of installation is clearly another factor to be taken into account The sensors need to interface easily with the control system The sensors or the moisture control system must be easy to operate and in particular must have an easy yet accurate calibration procedure As may be anticipated the sensor should be rugged, reliable and cost effective
Compared with other measurement techniques, microwave offers the best solution. The resistive techniques that attempt to relate the moisture to the electrical resistance or conductance of
may-June 2005 | 16
GFMT_MayJune05.indd 16
14/6/05 11:25:12
Feature
Figure 4: The Hydro-Mix V so also is the penetration of measurement. Hydronix has selected a frequency that will generally (depending on the properties of the material) penetrate by approximately 100mm. Hydronix are the only manufacturers to have adopted digital techniques that not only provide a greater accuracy and range of measurement compared to analogue techniques, but also greatly assist remote communication with the sensors. The sensors radiate an extremely low-powered electromagnetic microwave field into the material (significantly less than a mobile phone) which detects the resonant frequency of the system. Due to the dipolar effect of the water molecule, the resonant frequency changes with the changing water content. These changes are measured in unscaled units that are then scaled by a process of calibration to provide a precise readout of the moisture present. For standard
GreCon Qtr Pg Ad Grain&Feed 10.5.05 09:04 Page 1
the material are cheap and cheerful but fail to provide a reliable measurement as, for instance, rain water/distilled water does not conduct electricity whereas sea water certainly does. So this technique is severely affected by pollutants in the water. Capacitive techniques, which are more widely used, are a definite improvement, but nevertheless are still similarly affected by contaminants in the water. Infrared systems again are quite widely used but being a reflective technique only provide a surface measurement which will not be representative of the total moisture in the product. Nuclear techniques offer an accurate measurement technique, but are generally not practical as they need a relatively large volume of material in which to measure, they are not very user friendly and are relatively expensive. The microwave technique, as pioneered by Hydronix, provides a sound basis for measurement. The principal depends on the dipolar structure of the water molecule (Figure 1) that will try to align itself with the magnetic field to which it is subjected, in a similar way to a compass needle. When subjected to a rapidly changing electromagnetic field, such as in a microwave oven, the rapidly oscillating water molecule will expend energy which then heats the food. Thus, the interaction of the water molecule with a rapidly varying electromagnetic field provides a reliable basis for the measurement of water present in a material. Selecting a suitable frequency is important compromise. The higher the frequency of the EM field the less the measurement is affected by extraneous impurities, but
17 | may-June 2005
Extinguish sparks and embers without interrupting production Improve plant safety and reduce insurance risk Prevent plant downtime and protect production volumes
GreCon Limited, 4 Bridge View, Stepney Lane Newcastle upon Tyne NE1 6PN Tel: 0191 230 0660 Fax: 0191 230 3669 Web: www.grecon.de
Grain
GFMT_MayJune05.indd 17
14/6/05 11:25:15
Feature
applications default calibrations are written into the sensor. The sensors are internally compensated for changes in temperature, and also have a fast response external temperature sensor to provide a readout of the temperature of the material if required. Ensuring a sensor is correctly calibrated is Cost effective sensors & system probably the most import aspect for ensurThe total investment clearly needs to be ing consistent performance from the system. justified in relation to the benefits that accrue Hydro-Cal is a utility within the Hydro-Com as a result of installing a moisture control syssoftware package that greatly facilitates the tem. These are not always easy to quantify. calibration process, that is particularly approThe increased consistency of product will priate to the Hydro-Probe II sensors. This enables an accumulation of calibration data allow the producer to work more closely to be entered over a period of time, or all at to the permitted tolerances for the final once, that will provide the best fit calibration moisture content of the product, as well as a saving in energy by controlling line for the production processes more these caliFigure 5: Calibration curve closely, particularly with regard to drying processes. Feedback from customers indicate a payback period of months. Another factor is the life and cost of maintenance of the equipment. The sensors are extremely rugged and robust, constructed from stainless steel with extremely high wearing ceramic windows or face plates through which the electromagnetic field is radiated into the material. The sensors would normally be expected to last 10 years in the type of environment associated with animal feedmills. The cost of maintenance under normal circumstances is nil, and the power requirements absolutely minimal. With approaching 40,000 sensors operating in over 50 countries in a variety of industries, Hydronix has an established reputation for reliability of product and after sales service second to none. For
more inFormation:
bration points. Also the system is designed to assist calibration with only limited test results (Figure 5).
Differing materials will generally have different calibration parameters. The sensors, using If these are a flash eprom, may already known be remotely interrothen they may gated from a laptop be remoteor the host comly changed puter. The internal in the senparameter settings sor from the may be changed and computer or software upgraded the control using the Hydro-Com system. communication and For certain diagnostic software Figure 3: The Hydro-Probe II in process applipelletised material package available for cations, were free download from: absolute measwww.hydronix.com. urement is not so important as in relation to just maintaining a consistent moisture Ease of operation and calibration content, then it may not be necessary Once integrated with the control system to change the calibration settings when there should be no further requirement for changing materials. Instead it may be simattention, apart from periodically checking pler to just change the target value for the moisture content to be achieved. the calibration is satisfactory.
Grain
Hydronix Limited 7 Riverside Business Centre Walnut Tree Close Guildford Surrey GU1 4UG United Kingdom
Tel: +44 1483 468900 Fax: +44 1483 468919 Website: www.hydronix.com Email: info@hydronix.com
may-June 2005 | 18
GFMT_MayJune05.indd 18
14/6/05 11:25:18