You are on page 1of 7

P.M.Gedkar et al.

/ International Journal of Engineering Science and Technology (IJEST)

Finite Element Analysis of Pipe T-Joint


P.M.Gedkar#1,
#

Pg Student of Dept of Mechanical Engineering R.C.E.R.T, Chandrapur, India 1 priti_gedkar@rediffmail.com

Dr. D.V. Bhope *2


*

Professor, Dept of Mechanical Engineering R.C.E.R.T, Chandrapur, India 2 dvbhope@rediffmail.com

Abstract- This paper reports stress analysis of two pressurized cylindrical intersection using finite element method. The different combinations of dimensions of run pipe and the branch pipe are used to investigate the stresses in pipe at the intersection. In this study the stress analysis is accomplished by finite element package ANSYS. Keywords Stress analysis, Finite element method, Pipe T-joint. 1. Introduction A pipe is a general term used for hollow product having circular, elliptical or square cross section or for that matter cross section of any closed perimeter. A pipe is tubular product of cross section that has specific sizes and thicknesses governed by particular dimensional standards. Thus while tubes can be ordered for any outer diameter (DO), inner diameter (DI) or thickness, pipes have specific sizes and thickness and have to be ordered based on these size or thickness. A piping component experiences two main categories of stresses. The first category of stress comes from the pressure, either internal or external. The second category of stress comes from the forces and moments generated by weight, thermal expansion, wind, earthquake, and so forth. As the present work deals with the stresses due to internal pressure only, the discussion of stresses due to internal pressure is carried out in this work. Failure is a result of a stress condition which is more severe than the material can withstand. The actual condition may depart from those assumed at the design stage. Under a steady application of load (e.g. pressure), it ensures against failure of the system as perceived by one of the failure theories. If a pipe designed for a certain pressure experiences a much higher pressure, the pipe would rupture even if such load (pressure) is applied only once. The failure or rupture is sudden and complete. Such a failure is called catastrophic failure. The causes of failures may be due to following The actual loading may exceed the expected value. Stress concentration at the intersection. The main cause of pipe T-joint failure is the maximum Von-mises stress induced at the intersection of pipe Tjoint. Hence it is necessary to evaluate the stress at the intersection of pipe T-joint.

2. Literature Review Many researchers carried out in pipe T-joint stress analysis. Farid Vakili - Tahami, Mohammad Zehsaz[1] investigated the thermo-mechanical stresses as well as the temperature distribution along the pipe wall thickness. The results highlight the fact that to evaluate the risk of burn-through, not only the inner wall temperature of the main pipe should be checked against the critical level of 980oC, but also the level of the effective stresses must be compared against the temperature dependent yield stress of the material. Shiji Guo, Ryoko Morishima[2] investigated stress and buckling analysis and experiment of a composite sandwich T-joint under shear load were conducted. The result shows that, the traditional T-joint configuration has advantages in both strength and stiffness at the cost of manufacture complexity. Improved design options for lower cost and simpler manufacture process were also proposed and analyzed the result. T. Ahmad, M. A. Khan and D. Redekop [3] investigated the quantitative information for the stress concentration and collapse load of

ISSN : 0975-5462

Vol. 4 No.01 January 2012

163

P.M.Gedkar et al. / International Journal of Engineering Science and Technology (IJEST)

pressurized shell intersections without and with local area wall thinning. Experimental results are not available for comparison. In future work it is intended to determine the effect of further mesh modification on the numerical results, to find results for other types of local area wall thinning, and to determine the fatigue characteristics of intersections under cyclical loading.

3. Scope and Methodology It is evident from the geometry of pipe T-joint that, there is change in geometry at the intersecting junction which leads to stress concentration effect at the intersecting junction. Due to this, probability of failure increases at this location. It is seen from literatures that, no appropriate finding are available for stresses at intersecting junction with respect to variation of geometry of run pipe and branch pipe. In this work an effort is made to study the stresses at intersecting junction by varying the geometrical parameters of run and branch pipe. T pipe joint is considered for stress analysis. The finite element analysis is carried out by using ANSYS. The loading under only internal pressure is considered. The results of the finite element analysis for certain locations are verified with the help of standard analytical relations of pipe. Nomenclature of pipe T-joint is shown in Fig.1. The finite element analysis of pipe T-joint is performed by considering the following parameter. Variation in the outer diameter ratio of run pipe and branch pipe.[(DO)b/(DO)r] from 1 to 0.4. Variation in thickness of run pipe and branch pipe.[(DI)b/(DO)b] &[(DI)r/(DO)r] from 1 to 0.4. Variation in the included angle between run pipe & branch pipe () from 300 to 900.

Fig. 1 Nomenclature of Pipe T-Joint

Where, (DI)b (DO)b (DI)r (DO)r

= Inner diameter of branch pipe. = Outer diameter of branch pipe. = Inner diameter of run pipe. = Outer diameter of run pipe. = Included angle.

Results obtained by finite element analysis are compared with analytical analysis for location away from intersecting junction. 4. Model of Pipe T-Joint In this work simple pipe T-joint is used for analysis. The branch pipe is attached with run pipe with an angle of 900. The model is shown in Fig.2, in which ANSYS is used for modeling the pipe T-joint. The model has main pipe length of 300mm and branch pipe of 150mm. The advantage of symmetry is taken while analysis by imposing symmetric boundary conditions and the quarter model of pipe T-joint is shown in Fig.3.

ISSN : 0975-5462

Vol. 4 No.01 January 2012

164

P.M.Gedkar et al. / International Journal of Engineering Science and Technology (IJEST)

Fig. 2 Pipe T-joint

Fig. 3 One Fourth Model of Pipe T-Joint

5. Results The analysis reveals the stress distribution over the pipe T-joint. The location of maximum stress is present at the intersection of pipe. The results are presented in forthcoming sections. 5.1 Stresses in pipe T-Joint with respect to variation in (DO)b/(DO)r and (DI)r/(DO)r The stress analysis of pipe T-joint with (DO)b/(DO)r =1 revealed the stresses at pipe intersection. Vonmises stresses at the intersection are shown in Table 1. These stress values are evaluated for (DI)b/(DO)b varying from 0.8 to 0.96 and (DI)r/(DO)r varying from 0.8 to 0.96.
Table 1 Maximum Von-Mises Stresses (Mpa) at the Intersection of Pipe

(DI)b/(DO)b 0.96 0.8 0.84 0.88 0.92 0.96 174.87 101.24 76.008 61.207 51.714

(DI)r/(DO)r 0.92 0.88 0.84 Maximum Von-Mises Stresses (Mpa) 94.939 86.135 73.978 78.033 60.942 50.564 60.933 50.49 42.815 50.578 43.655 38.072 43.676 37.566 33.666

0.8 56.158 43.158 37.335 34.001 31.347

The values of the Maximum Von-Mises Stresses at the intersection of the pipe T-joint are plotted in Fig.4.

Fig. 4-Variation of Max. Von Mises Stresses at the Intersection of Pipe

The following Fig. 5 and Fig. 6 shows the variation of Max. Von-mises stress in the branch pipe and run pipe away from the intersection.

ISSN : 0975-5462

Vol. 4 No.01 January 2012

165

P.M.Gedkar et al. / International Journal of Engineering Science and Technology (IJEST)

Fig. 5 - Variation of Max. Von-Mises Stresses away from Intersection in Branch Pipe

Fig. 6 - Variation of Max. Von-Mises Stresses away from Intersection in Run Pipe

Figure 7 & 8 shows the comparison between hoop stresses calculated analytically and by FEM away from intersection.

Fig. 7 Comparison between hoop stresses calculated analytically and by FEM away from intersection in Branch Pipe

Fig. 8 - Comparison between Hoop stresses calculated analytically and by FEM away from intersection in Run Pipe

It is seen from the Fig.7, 8 that the hoop stresses away from intersection evaluated analytically and by FEM are quite closer. This verifies the exactness of FE solution. The stress analysis of pipe T-joint with (DO)b/(DO)r =0.8 revealed the stresses at pipe intersection. These stress values are evaluated for (DI)b/(DO)b varying from 0.75 to 0.95 and (DI)r/(DO)r varying from 0.8 to 0.96. The values of the Max. Von-mises stresses at the intersection of the pipe T-joint are plotted in Fig. 9.

Fig. 9 - Variation of Max. Von-Mises Stresses at the Intersection of Pipe

ISSN : 0975-5462

Vol. 4 No.01 January 2012

166

P.M.Gedkar et al. / International Journal of Engineering Science and Technology (IJEST)

The stress analysis of pipe T-joint with (DO)b/(DO)r =0.6 revealed the stresses at pipe intersection. These stress values are evaluated for (DI)b/(DO)b varying from 0.667 to 0.93 and (DI)r/(DO)r varying from 0.8 to 0.96. The values of the Von-mises stresses at the intersection of the pipe T-joint are plotted in the Fig. 10.

Fig. 10 - Variation of Max. Von-Mises Stresses at the Intersection of Pipe

The stress analysis of pipe T-joint with (DO)b/(DO)r =0.4 revealed the stresses at pipe intersection. These stress values are evaluated for (DI)b/(DO)b varying from 0.5 to 0.9 and (DI)r/(DO)r varying from 0.8 to 0.96. The values of the Max. Von-mises stresses at the intersection of the pipe T-joint are plotted in the Fig. 11.

Fig. 11 - Variation of Von-Mises Stresses at the Intersection of Pipe

5.2 Stresses in pipe T-Joint with respect to variation in (DO)b/(DO)r , (DI)r/(DO)r and included angle The stress analysis of pipe T-joint with (DO)b/(DO)r = 1 for included angle = 600 revealed the stresses at pipe intersection. These stress values are evaluated for (DI)b/(DO)b varying from 0.8 to 0.96 and (DI)r/(DO)r varying from 0.8 to 0.96. The values of the Max. Von-mises stresses at the intersection of the pipe T-joint are plotted in the Fig. 12.

ISSN : 0975-5462

Vol. 4 No.01 January 2012

167

P.M.Gedkar et al. / International Journal of Engineering Science and Technology (IJEST)

Fig. 12 - Variation of Max. Von-Mises Stress with Included Angle 600 at Intersection

The stress analysis of pipe T-joint with (DO)b/(DO)r = 1 for included angle = 450 revealed the stresses at pipe intersection. These stress values are evaluated for (DI)b/(DO)b varying from 0.8 to 0.96 and (DI)r/(DO)r varying from 0.8 to 0.96. The values of the Max. Von-mises stresses at the intersection of the pipe T-joint are plotted in Fig. 13

Fig. 13 - Variation of Max. Von-Mises Stress with Included Angle 450 at Intersection

The stress analysis of pipe T-joint with (DO)b/(DO)r = 1 for included angle = 300 revealed the stresses at pipe intersection. These stress values are evaluated for (DI)b/(DO)b varying from 0.8 to 0.96 and (DI)r/(DO)r varying from 0.8 to 0.96. The values of the Max. Von-mises stresses at the intersection of the pipe T-joint are plotted in the Fig. 14.

Fig. 14 - Variation of Max. Von-Mises Stress with Included Angle 300 at Intersection

ISSN : 0975-5462

Vol. 4 No.01 January 2012

168

P.M.Gedkar et al. / International Journal of Engineering Science and Technology (IJEST)

6. Discussion Conclusion 1. It is observed from the Figs. 4, 9, 10, 11 that as the thickness of branch pipe goes on reducing the stress at the intersecting junction are also reducing, and as thickness of run pipe increases the stresses are also reducing at the intersecting junction. It means the behaviour of stress at intersection is exactly reversed for branch pipe thickness and run pipe thickness. It means that the lower value of branch pipe thickness are preferable for lower stress values at intersecting junction provided the stresses in branch pipe are within the safe limits. This reduction of stresses at the intersection with lesser branch pipe thickness may be due to the less constraining effect of branch pipe on the run pipe. From Figs. 4, 9, 10, 11 it is observed that as the thickness of run pipe increases, there is no appropriable change in Von-mises stress at intersecting junction with respect to change in branch pipe thickness. Thus for thicker run pipe the variation in the thicknesses in branch pipe do not play important role in reduction of Von-mises stresses at intersection. From Table no. 1 and also from the Figs. 4, 9 it is observed that, as the thickness of run pipe & the branch pipe reduces the stresses in the branch & run pipe away from the intersection point increases. Though it is desirable to have the lesser value of branch pipe thickness for lesser von-mises stress at intersection point but lesser thickness of branch pipe will lead to increase in the stresses in the branch pipe. Thus the thickness of branch pipe plays a dominating role in the stress distribution at intersection point. Thus, judicial choice is necessary to decide the branch pipe thickness. It is seen from the Fig. 4, 9, 10, 11, 12, 13 & 14 that as included angle between the branch pipe and run pipe varies from 900 to 300 , the stress levels goes on increasing. The trend of variation in nature of stresses is almost identical for all the cases. Thus the 900 included angle give the least stress values than that of 300 included angle. This rise in stress with respect to decreasing the angle between run pipe and branch pipe may be due to increase in stress concentration effect due to oblong opening at the run pipe.

2.

3.

4.

References
[1] [2] [3] [4] [5] [6] Farid Vakili - Tahami, Mohammad Zehsaz. Finite Element Analysis of in welding of T-joint pipe European Journal of Scientific Research ISSN 1450-216X Vol.40 No.4 (2010), pp.557-568 EuroJournals Publishing, Inc. 2010 Shiji Guo, Ryoko Morishima. Sandwich T-joint structure with & without cutout under shear load. Paper presentation The Ohio State University. T. Ahmad, M. A. Khan and D. Redekop Pressurised Shell Intersections with Local Area Wall Thinning paper presentation SMIRT 19, Toronto, Transactions, August 2007. H. Salem, E. A. Soliman, S. A. Ibrahim and K. F. FakhrY Strength of hollow section t-joints under bending moments paper presentation of Ain Shams University Faculty of Engineering Department of Structural Engineering 2007. Lip.H.Teh, Kim J.R. Rasmussen Strength of welded T joint truss connection between equal width cold formed RHS.

ISSN : 0975-5462

Vol. 4 No.01 January 2012

169

You might also like