You are on page 1of 160

FILE NO.

E06-111

R410A

WARNINGS ON REFRIGERANT LEAKAGE


Refrigerant density limit
Important The room in which the air conditioner is to be installed should be designed or chosen such that in the event of a refrigerant gas leak the density of gas should not exceed a set limit.

The refrigerant R-410A, which is used in the air conditioner product, is intrinsically safe without the toxicity or combustibility of ammonia. R-410A is environmentally friendly and is not restricted by current or pending laws intended to protect the ozone layer.

Risk of suffocation through leakage of R-410A is minimal. However, with the recent increase in the number of high density buildings and use of multi air conditioner systems to ensure effective use of floor space, energy conservation and individual control, installers should ensure it is not possible to exceed density limits in the event of a refrigerant leak. In particular, where a single unit of the multi conditioner system is to be installed into a small room, select a suitable model and installation procedure so that if refrigerant leaks out, density limits are not exceeded. In a room where there is a risk of the density limit being exceeded, create an opening with adjacent rooms, or install mechanical ventilation combined with a gas leak detection device.

The density can be calculated as shown below; Total amount of refrigerant (kg) Min. volume of the indoor unit installed room (m3) density limit (kg/m3)

The density calculation must be carried out in accordance with local regulation or guideline like BS EN 378 The above procedure must be completed in accordance with local, national and international standards, code of practice and statutory requirements.

Note 1: If there are 2 or more refrigerating systems in a single area, the amount of refrigerant should be charged as required for each individual unit. For the amount of charge in this example: The possible amount of leaked refrigerant gas in rooms A, B and C is 10 kg. The possible amount of leaked refrigerant gas in rooms D, E and F is 15 kg.

Outdoor unit e.g. charged amount (10 kg) e.g. charged amount (15 kg)

Room A

Room B

Room C

Room D

Room E Indoor unit

Room F

Note 2: The standards for minimum room volume are as follows: (1) No partition (shaded portion)

Outdoor unit

(2) When there is an effective opening with the adjacent room for ventilation of leaking refrigerant gas (opening without a door, or an opening 0.15% or larger than the respective floor spaces at the top or bottom of the door).

Refrigerant piping Indoor unit

(3) If an indoor unit is installed in each partitioned room and the refrigerant tubing is interconnected, attention must be paid to ensure safeguards are in place to avoid density limits being exceeded in each partitioned area. When leak detection is interlocked with mechanical ventilation equipment is installed in the smallest room where the density limit is exceeded, the volume of the next smallest room becomes the object.

Refrigerant piping

Outdoor unit Very small room Small room Medium room Large room Indoor unit

Mechanical ventilation device - gas leak detector

Note 3: The minimum indoor floor area compared with the amount of refrigerant is roughly as follows (when the ceiling is 2.7 m high):

m2

Range below the density limit of 0.3 kg/m 3 (countermeasures not needed)

Min. indoor floor area

Range above the density limit of 0.3 kg/m 3 (countermeasures needed

kg Total refrigerant amount

Outline (Tentative)
World-class energy savings _COP of 4.61* achieved by Toshiba's unrivalled S-MMS technologies and newly developed components *4HP CDU system Quiet operation can be further enhanced with an optional PMV (flow regulating valve) Kit.

*Pulse Motor Valve

Versatile application _13 types of indoor units for use in up to 9 rooms (6 HP)
Sales launch scheduled for early 2006. Specifications differ by region. For questions regarding availability, please contact your local distributor.

PMV Kit

New compact 4-way cassette

Use of quieter place


Necessity of PMV Kit (RBM-PMV0361E / RBM-PMV0901E) for quieter place application as an optional.

Outdoor unit line-up


Appearance Model name 50Hz Model name 60Hz

MCY-MAP0401HT

MCY-MAP0401HT2D

MCY-MAP0501HT

MCY-MAP0501HT2D

MCY-MAP0601HT

MCY-MAP0601HT2D

Indoor unit line-up


Cooling capacity (kW) (HP equivalent)
4-way Air Discharge Cassette Compact 4-way Cassette (600 x 600) 2-way Air Discharge Cassette 1-way Air Discharge Cassette Concealed Duct Standard

2.2 0.8

2.8 1.0

3.6 1.25

4.5 1.7

5.6 2.0

7.1 2.5

8.0 3.0

9.0 3.2

11.2 14.0 4.0 5.0

MMU-AP***1H MMU-AP***1MH MMU-AP***1WH MMU-AP***1YH / -AP***2SH MMD-AP***1BH MMD-AP***1SPH MMD-AP***1H MMC-AP***1H MMK-AP***1H MMK-AP***2H MML-AP***1H MML-AP***1BH MMF-AP***1H

Slim Duct

Concealed Duct High Static Pressure

Under Ceiling

High Wall 1series

High Wall 2series

Floor Standing Cabinet

Floor Standing Concealed

Floor Standing

Mini-SMMS Design Manual


0 0

Contents
- Warning on refrigerant leakage - Outline - Line-up

1.Design methods ............................................................................11-1


1-1. 1-2. 1-3. 1-4. 1-5.

1-2 System overview ...............................................................................1Basic system configuration ..............................................................1-10 1-16 Equipment selection procedure .......................................................1-26 ......................................................................... Piping requirements 1-26 ............................................................................... Wiring guideline 1-40

2-1 2.Indoor units ......................................................................................2-1

2-2 2-1. 4-way Air Discharge Cassette type ...................................................2-2 ........................................ 2-7 2-2. Compact 4-way Cassette(600 x 600) type 2-5 ................................................. 2-11 2-3. 2-way Air Discharge Cassette type 2-8 ................................................. 2-17 2-4. 1-way Air Discharge Cassette type 2-13 ....................................................... 2-23 2-5. Concealed Duct Standard type 2-17 2-30 2-6. Slim Duct type .................................................................................2-22 ..................................... 2-38 2-7. Concealed Duct High Static Pressure type 2-29 ........................................................................... 2-43 2-8. Under Ceiling type 2-33 .................................................................... 2-47 2-9. High Wall 1 series type 2-36 .................................................................... 2-53 2-10. High Wall 2 series type 2-4 ............................................................ 2-57 2-11. Floor Standing Cabinet type 2-44 ....................................................... 2-61 2-12. Floor Standing Concealed type 2-4 ......................................................................... 2-65 2-13. Floor Standing type 2-5 ................................................... 2-70 2-14. Application controls of indoor unit 2-54

3-1 3.PMV Kit................................................................................................3-1 3-2 3-1. Selection of PMV Kit .........................................................................3-2 ............................................................................ 3-2 3-2. Wiring connections 3-2 ....................................................................................... 3-3 3-3. Dimensions 3-3

4-1 4.Outdoor units ..................................................................................4-1 4-2 4-1. Outdoor units ....................................................................................4-2 ........................................................... 4-5 4-2. Branching joints and headers 4-5 ................................................... 4-7 4-3. Application controls of outdoor unit 4-7

5-1 5.Controls ..............................................................................................5-1

5-3 5-1. Control devices .................................................................................5-3 ...................................................................................... 5-11 5-2. Dimensions 5-11

MEMO

1. Design methods

1-1. System overview ......................................................................11-2


1-1-1. Outdoor units......................................................................11-2 ........................................................................ 1-1-2. Indoor units 11-3 ............................................. 1-1-3. Branching joints and headers 1-5 .............................................................................. 1-1-4. PMV Kit 11-5 ............................................................... 1-1-5. Remote controller 1-6 11-2. Basic system configuration.................................................1-10 10 1-1 1-3. Equipment selection procedure..........................................1-16 1-3-1. Selection flow chart ..........................................................1-16 11-3-2. Combination conditions for indoor unit and outdoor unit ...............................................................1-17 1-1 ............................ 1-17 1-3-3. Cooling/heating capacity characteristic 1-1 ....................................... 1-3-4. Example of equipment selection 1-3 1-23 1-2 1-4. Piping requirements ..............................................................1-26 1-4-1. Free branching system .....................................................1-26 1-2 ......................... 1-4-2. Refrigerant piping length and piping size 1-2 1-27 1-4-3. Refrigerant piping length and piping size with PMV Kit .....................................................................1-31 1-3 ............................................... 1-4-4. Refrigerant piping example 1-3 1-35 ............. 1-4-5. Charging requirement with additional refrigerant 1-3 1-39 1-4 1-5. Wiring guideline ......................................................................1-40 1-5-1. General.............................................................................1-40 1-4 ............................................. 1-5-2. Connection of power supply 1-4 1-40 ..................................................... 1-5-3. Electrical wiring design 1-1 1-41 .................................................... 1-5-4. Design of control wiring 1-4 1-42 ..................................... 1-5-5. Example of system wiring design 1-4 1-43 ................................................... 1-5-6. Electrical characteristics 11-45 45

1-1

1-1. System Overview


1-1-1. Outdoor units
Corresponding HP Model name Heat pump(50Hz) MCYHeat pump(60Hz) MCYInverter unit 4HP MAP0401HT MAP0401HT2D 12.1 12.5 6
o o

5HP MAP0501HT MAP0501HT2D 14.0 16.0 8


o

6HP MAP0601HT MAP0601HT2D 15.5 18.0 9

Cooling capacity(kW)*1 Heating capacity(kW)*1 No.of connectable indoor units

*1 Rated conditions
Cooling:Indoor air temperature 27 C DB/19 CWB,Outdoor air temperature 35 CDB o o o Heating:Indoor air temperature 20 C DB,Outdoor air temperature 7 CDB/6 CWB

Allocation standard of model name


MCY- M AP H T 2D
No mark:Power supply specification, 1O / 220/230/240V, (50Hz) 2D :Power supply specification, 1O / 220V, 60Hz T : Inverter Unit H : Heat pump Development Number Capacity rank HP x 10 R410A M : Individual Unit Multi Compact Type

1-2

1-1-2. Indoor units


Type Appearance Model name
MMU-AP0091H MMU-AP0121H MMU-AP0151H MMU-AP0181H 4-way Air Discharge Cassette Type MMU-AP0241H MMU-AP0271H MMU-AP0301H MMU-AP0361H MMU-AP0481H MMU-AP0071MH Compact 4-way Air Discharge (600x600) Type MMU-AP0091MH MMU-AP0121MH MMU-AP0151MH MMU-AP0181MH MMU-AP0071WH MMU-AP0091WH MMU-AP0121WH 2-way Air Discharge Cassette Type MMU-AP0151WH MMU-AP0181WH MMU-AP0241WH MMU-AP0271WH MMU-AP0301WH MMU-AP0071YH MMU-AP0091YH 1-way Air Discharge Cassette Type MMU-AP0121YH MMU-AP0152SH MMU-AP0182SH MMU-AP0242SH MMD-AP0071BH MMD-AP0091BH MMD-AP0121BH MMD-AP0151BH Concealed Duct Standard Type MMD-AP0181BH MMD-AP0241BH MMD-AP0271BH MMD-AP0301BH MMD-AP0361BH MMD-AP0481BH MMD-AP0071SPH MMD-AP0091SPH Slim Duct Type MMD-AP0121SPH MMD-AP0151SPH MMD-AP0181SPH MMD-AP0181H Concealed Duct High Static Pressure Type MMD-AP0241H MMD-AP0271H MMD-AP0361H MMD-AP0481H MMC-AP0151H MMC-AP0181H Under Ceilling Type MMC-AP0241H MMC-AP0271H MMC-AP0361H MMC-AP0481H

Capacity rank
009 type 012 type 015 type 018 type 024 type 027 type 030 type 036 type 048 type 007 type 009 type 012 type 015 type 018 type 007 type 009 type 012 type 015 type 018 type 024 type 027 type 030 type 007 type 009 type 012 type 015 type 018 type 024 type 007 type 009 type 012 type 015 type 018 type 024 type 027 type 030 type 036 type 048 type 007 type 009 type 012 type 015 type 018 type 018 type 024 type 027 type 036 type 048 type 015 type 018 type 024 type 027 type 036 type 048 type

Heating Cooling Capacity capacity (kW) capacity (kW) code


1.00 1.25 1.70 2.00 2.50 3.00 3.20 4.00 5.00 0.80 1.00 1.25 1.70 2.00 0.80 1.00 1.25 1.70 2.00 2.50 3.00 3.20 0.80 1.00 1.25 1.70 2.00 2.50 0.80 1.00 1.25 1.70 2.00 2.50 3.00 3.20 4.00 5.00 0.80 1.00 1.25 1.70 2.00 2.00 2.50 3.00 4.00 5.00 1.70 2.00 2.50 3.00 4.00 5.00 2.8 3.6 4.5 5.6 7.1 8.0 9.0 11.2 14.0 2.2 2.8 3.6 4.5 5.6 2.2 2.8 3.6 4.5 5.6 7.1 8.0 9.0 2.2 2.8 3.6 4.5 5.6 7.1 2.2 2.8 3.6 4.5 5.6 7.1 8.0 9.0 11.2 14.0 2.2 2.8 3.6 4.5 5.6 5.6 7.1 8.0 11.2 14.0 4.5 5.6 7.1 8.0 11.2 14.0 3.2 4.0 5.0 6.3 8.0 9.0 10.0 12.5 16.0 2.5 3.2 4.0 5.0 6.3 2.5 3.2 4.0 5.0 6.3 8.0 9.0 10.0 2.5 3.2 4.0 5.0 6.3 8.0 2.5 3.2 4.0 5.0 6.3 8.0 9.0 10.0 12.5 16.0 2.5 3.2 4.0 5.0 6.3 6.3 8.0 9.0 10.0 16.0 5.0 6.3 8.0 9.0 12.5 16.0

PMV Kit

Available Available Available Available Available

Available Available Available Available Available Available

Available Available Available Available Available

1-3

Type

Appearance

Model name
MMK-AP0071H MMK-AP0091H MMK-AP0121H MMK-AP0151H MMK-AP0181H MMK-AP0241H MMK-AP0072H

Capacity rank
007 type 009 type 012 type 015 type 018 type 024 type 007 type 009 type 012 type 007 type 009 type 012 type 015 type 018 type 024 type 007 type 009 type 012 type 015 type 018 type 024 type 015 type 018 type 024 type 027 type 036 type 048 type

Capacity code
0.80 1.00 1.25 1.70 2.00 2.50 0.80 1.00 1.25 0.80 1.00 1.25 1.70 2.00 2.50 0.80 1.00 1.25 1.70 2.00 2.50 1.70 2.00 2.50 3.00 4.00 5.00

Heating Cooling capacity (kW) capacity (kW)


2.2 2.8 3.6 4.5 5.6 7.1 2.2 2.8 3.6 2.2 2.8 3.6 4.5 5.6 7.1 2.2 2.8 3.6 4.5 5.6 7.1 4.5 5.6 7.1 8.0 11.2 14.0 2.5 3.2 4.0 5.0 6.3 8.0 2.5 3.2 4.0 2.5 3.2 4.0 5.0 6.3 8.0 2.5 3.2 4.0 5.0 6.3 8.0 5.0 6.3 8.0 9.0 10.0 16.0

PMV Kit
Available Available Available Available Available Available Available Available Available Available Available Available Available Available Available

High Wall Type (1 series)

High Wall Type (2 series)

MMK-AP0092H MMK-AP0122H MML-AP0071H MML-AP0091H

Floor Standing Cabinet Type

MML-AP0121H MML-AP0151H MML-AP0181H MML-AP0241H MML-AP0071BH MML-AP0091BH

Floor Standing Concealed Type

MML-AP0121BH MML-AP0151BH MML-AP0181BH MML-AP0241BH MMF-AP0151H MMF-AP0181H MMF-AP0241H MMF-AP0271H MMF-AP0361H MMF-AP0481H

Floor Standing Type

Allocation standard of model name


MM AP H -

C : China model M : Compact 4-way Cassete Type W: 2way Cassette Type S : 1way Cassette Type Y : Small sized 1way Cassette Type B : Built-in Type (Built-in Duct Type) (Floor concealed type) SP(S):Slim Duct Type Development series No. Based on the cooling capacity (Btu/h) /1,000 R410A U : Cassette Type C : Under Ceiling Type D : Duct Type K : High Wall Type L : Floor Type (Cabinet type) (Concealed type) F : Floor Standing Type MM : Modular Multi Type

1-4

1-1-3. Branching joints and headers *1


Model name Usage Appearance

RBM-BY53E Y-shape branching joint RBM-BY103E

Indoor unit capacity code (*2) :Total below 6.4

Indoor unit capacity code (*2) :Total 6.4 or more and below 7.8

4-branching header

RBM-HY1043E Indoor unit capacity code (*2) :Total below 7.8

8-branching header

RBM-HY1083E Indoor unit capacity code (*2) :Total below 7.8

*1 If total capacity code value of indoor unit exceeds that of outdoor unit, apply code of outdoor unit. *2 "capacity code" can be obtained from page 1-17. (capacity code is not actual capacity) *3 When using Y-shape branching joint for 1st branching, select according to the capacity code of outdoor unit.

1-1-4. PMV Kit


Model name Indoor unit capacity type Appearance

RBM-PMV0361E

007, 009, 012 type

RBM-PMV0901E

015, 018, 024 type

For more information see section 3.

1-5

1-1-5. Remote controller


Name Model name Appearance Application Function

Connected to indoor unit

Start / Stop Mode Change Temperature setting Fan speed Timer function
1

On or off elapsed timer with 30 minutes increments. Automatic off function.

Weekly when combined with RBC-EXW21E2 weekly schedule operation can be operated.

Wired remote controller

RBC-AMT31E

Filter dirty indicator Displays automatically maintenance time of indoor filter by flashes. Self-diagnosis function
Wired remote controller Wired remote controller (In case of control by 2 remote controllers)

Pressing "CHECK" button displays status code. Control by 2 remote controllers is available. Two remote controllers can be connected to one indoor unit. The indoor unit can be separately operated from a different location.

Connected to indoor unit

Start / Stop Temperature setting Change of air flow

Simple wired remote controller

Check code display

RBC-AS21E2

TEST
SETTING

C F

Simple remote controller

1-6

Name Model name

Appearance

Function

Start / Stop

TCB-AX21U(W)-E2

Mode change Temperature setting Change of air flow Timer function On or off timer operation, setting in 30 minutes increments. Automatic Off function. Control by 2 remote controllers is available. Two wireless remote controllers can operate one indoor unit. The indoor

Wireless remote controller kit

RBC-AX22CE2

unit can be separately operated from a different location. Check code display TCB-AX21U(W)-E2 (for 4-way airdischarge cassette) RBC-AX22CE2 (for under ceiling) TCB-AX21-E2 (for other units except for the concealed duct high static pressure)

TCB-AX21E2

1-7

Name

Model name

Appearance

Application

Performance

Connected to outdoor unit, or indoor unit


Outdoor unit

Individual control up to 64 indoor units. Individual control for max. 64 indoor units divided into 4 zones. Up to 16 indoor units for each zone Up to 16 outdoor units are connectable.

Central remote controller

ZONE ALL ZONE GROUP

TCB-SC642TLE2

CODE No. 1234


SET DATA SETTING

Four selectable central control settings to restrict individual remote controller operations. Setting for one of 1 to 4 zones is available.

UNIT No. No.

TEST

R.C.

GROUP SELECT ZONE

Central remote controller


CL SET

Can be used with other central control devices (Up to 10 central control devices with in one control circuit) Two selectable control modes Central controller mode Remote controller mode Setting of simultaneous ON/OFF 3 times for each day of the week combined with a weekly timer.

Central remote controller

Indoor remote controller

Connected to outdoor unit, or indoor unit

Individual control up to 16 indoor units. Setting of simultaneous ON-OFF 3 times for each day of the week when combined with a weekly timer. Connected to 2 remote controllers is possible.

Outdoor unit

ON-OFF controller

TCB-CC163TLE2

ON-OFF controller

Indoor unit

ON-OFF controller Indoor remote controller

1-8

Name

Model name

Appearance

Application

Performance

Weekly schedule operation Connected to central remote controller or wired remote controller
1 Setting different start / stop time for

each day of the week


2 ON / OFF can be set 3 times

a day.
ON OFF ON OFF ON OFF

8:00

12:00 13:00 18:00 19:00 21:00

3 "CHECK" "PROGRAM" "DAY"


Wired remote controller Weekly timer

button copying of settings easy.


4 Two different schedules for a

RBC-EXW21E2

Weekly timer

SuMoTuWeTh Fr Sa
PROGRAM1 PROGRAM2 PROGRAM3
ERROR

week can be specified. (Summer schedule and winter schedule, etc.)


5 "CANCEL" "DAY" button enables

WEEKLY TIMER

holiday setting.
6 If power supply fails, the setting
Outdoor unit

contents are stored in the memory for 100 hours.

Central remote controller

Weekly timer

1-9

1-2. Basic system configuration


The following shows an example of Basic system configuration
1

In case of without "PMV Kit"

Reference example 1

4HP system
MAX.indoor unit : 6 units Capacity code of indoor unit Min. : 3.2 Max.: 5.2
Capacity code Total : 4.8 No.of total units 6

Outdoor unit 4HP

MCY-MAP0401HT MCY-MAP0401HT2D
Capacity code over the branch 0.8+0.8=1.6

Cooling capacity 12.1 kW Heating capacity 12.5 kW

4.8

2.4

1.6

0.8

Indoor unit designation

007 (0.8)

007 (0.8)

007 (0.8)

Capacity code

2.4

1.6

0.8

Indoor unit Remote controller

007 (0.8)

007 (0.8)

007 (0.8)

1-10

In case of without "PMV Kit"

Reference example 2

5HP system
MAX.indoor unit : 8 units Capacity code of indoor unit Min. : 4.0 Max.: 6.5
Capacity code Total : 6.4 No.of total units 8

Outdoor unit 5HP

MCY-MAP0501HT MCY-MAP0501HT2D

Cooling capacity 14.0 kW Heating capacity 16.0 kW

6.4

3.2

2.4

1.6

0.8

Indoor unit designation

007 (0.8)

007 (0.8)

007 (0.8)

007

Capacity code

(0.8)

3.2

2.4

1.6

0.8

Indoor unit Remote controller

007 (0.8)

007 (0.8)

007 (0.8)

007 (0.8)

1-11

In case of without "PMV Kit"

Reference example 3

6HP system
MAX.indoor unit : 9 units Capacity code of indoor unit Min. : 4.8 Max.: 7.8
Capacity code Total : 7.6 No.of total units 9

Outdoor unit 6HP

MCY-MAP0601HT MCY-MAP0601HT2D

Cooling capacity 15.5 kW Heating capacity 18.0 kW

7.6

2.6

1.8

1.0

Indoor unit designation

007 (0.8)

007 (0.8)

009 (1.0)

Capacity code

5.0

2.6

1.6

0.8

009 (1.0)

007 (0.8)

007 (0.8)

2.4

1.6

0.8

Indoor unit Remote controller

007 (0.8)

007 (0.8)

007 (0.8)

1-12

In case of "PMV Kit"

Reference example 4

4HP system
MAX.indoor unit : 6 units Capacity code of indoor unit Min. : 3.2 Max.: 5.2
Capacity code Total : 4.8 No.of total units 6

Outdoor unit 4HP

MCY-MAP0401HT MCY-MAP0401HT2D
Capacity code over the branch 0.8+0.8=1.6

Cooling capacity 12.1 kW Heating capacity 12.5 kW

4.8

2.4

1.6

0.8

Indoor unit designation

007 (0.8)

007 (0.8)

007 (0.8)

Capacity code

2.4 PMV Kit Indoor unit Remote controller 007 (0.8)

1.6

0.8

007 (0.8)

007 (0.8)

1-13

In case of "PMV Kit"

Reference example 5

5HP system
MAX.indoor unit : 8 units Capacity code of indoor unit Min. : 4.0 Max.: 6.5
Capacity code Total : 6.4 No.of total units 8

Outdoor unit 5HP

MCY-MAP0501HT MCY-MAP0501HT2D

Cooling capacity 14.0 kW Heating capacity 16.0 kW

6.4

3.2

2.4

1.6

0.8

Indoor unit designation

007 (0.8)

007 (0.8)

007 (0.8)

007

Capacity code

(0.8)

3.2 PMV Kit Indoor unit Remote controller 007 (0.8)

2.4

1.6

0.8

007 (0.8)

007 (0.8)

007 (0.8)

1-14

In case of "PMV Kit"

Reference example 6

6HP system
MAX.indoor unit : 9 units Capacity code of indoor unit Min. : 4.8 Max.: 7.8
Capacity code Total : 7.6 No.of total units 9

Outdoor unit 6HP

MCY-MAP0601HT MCY-MAP0601HT2D

Cooling capacity 15.5 kW Heating capacity 18.0 kW

7.6

2.6

1.8

1.0

Indoor unit designation

007 (0.8)

007 (0.8)

009 (1.0)

Capacity code

5.0

2.6

1.6

0.8

009 (1.0)

007 (0.8)

007 (0.8)

2.4 PMV Kit Indoor unit Remote controller 007 (0.8)

1.6

0.8

007 (0.8)

007 (0.8)

1-15

1-3. Equipment selection procedure


1-3-1. Selection flow chart

Start STEP 1
Determination of indoor air conditioning load

STEP 2
Preliminary selection of indoor units

STEP 3
Preliminary selection of outdoor unit with indoor units

STEP 4
Capacity correction for piping length/height between indoor and outdoor units

STEP 5
Capacity correction based on indoor and outdoor temperature

STEP 6
Validate preliminary selection of indoor units

NO

STEP 7
Confirmation of selection for indoor unit and outdoor units

End

1-16

1-3-2. Combination conditions for indoor unit and outdoor unit


1 For indoor unit, the capacity code is decided for each capacity rank.
Capacity rank type Capacity code 007 0.8 009 1 012 1.25 015 1.7 018 2 024 2.5 027 3 030 3.2 036 4 048 5

NOTE :
Capacity rank : Correspondence to Btu/h. Capacity code : Correspondence to Horsepower.

2 For outdoor unit, maximum No. of connectable indoor units and total capacity code of indoor units are decided. Outdoor unit MCY-MAP0401HT MCY-MAP0401HT2D MCY-MAP0501HT MCY-MAP0501HT2D MCY-MAP0601HT MCY-MAP0601HT2D Capacity code of outdoor unit 4 5 6 Max. No. of indoor units 6 8 9 Total capacity code of indoor units 3.2 to 5.2 4.0 to 6.5 4.8 to 7.8

1-3-3. Cooling/heating capacity characteristics


1 Cooling capacity calculation method :

Required cooling capacity = Cooling capacity x Factor (


Indoor air wet bulb temperature vs. capacity correction value

*1) kW

Capacity correction value

1.2

(Example) Design Indoor conditions : 22oC WB Capacity correction value : 1.09

Capacity correction value

1.1 1.0 0.9 0.8 15 20 24


o

1.2 1.1 1.0 0.9 0.8 15 20 24

Indoor air wet bulb temp. ( C)


Outdoor air dry bulb temperature vs.capacity correction value

Indoor air wet bulb temp. (oC)

Capacity correction value

1.2 1.1 1 0.9 -5


Capacity correction value

(Example) Design Outdoor conditions : 17oC DB Capacity correction value : 1.14


1.2 1.1 1 0.9 -5

10

15

20

25

30

35

40 43

10

15

20

25

30

35

40 43

Outdoor air dry bulb temp. (oC)

Outdoor air dry bulb temp. (oC)

*1 : Coefficient to use for correction of outdoor unit capacity when total capacity of the indoor units are not equal to the outdoor unit capacity.
1-17

Air flow variation ratio of indoor unit vs. capacity correction (For concealed duct type only)

Capacity correction value

1.1

1.0

0.9 80 90 100 110 120

Air flow variation ratio (%)

Connecting pipe length and lift difference between indoor and outdoor units vs. capacity correction value

94

92

90

88

86

84

Hight of outdoor unit H (m)

20
100%

10

-10

-20 0 10 20 30 40 50 60 70 80 90 100

98

96

30

Pipe length (Equivalent length) L(m)


(Example) Design Pipelength : 55m Height of outdoor unit : 15m Capacity correction value : 89%
94 92 90 88 86 84

Outdoor unit L is the longest one of (Ll + a, Ll + b, Ll + c) H = ho + (Largest one of ha, hb, and hc) ha

82

20
100%

10

hc

hb

a b c

A B Indoor unit C

-10

-20 0 10 20 30 40 50 60 70 80 90 100

98

ho

Ll

Hight of outdoor unit H (m)

96

30

Pipe length (Equivalent length) L(m)

1-18

82

Correction of outdoor unit diversity


(Example) Design Outdoor unit Indoor units total capacity (Capacity ratio Capacity correction value
Capacity correction value
1.1 1 0.9 0.8 0.7 80 80 100 110 120 130

Capacity correction value

1.1 1 0.9 0.8 0.7 80 80 100 110 120 130

: 5.0HP : 5.5HP : 110%) : 1.03%

Standard capacity ratio Indoor units total capacity ratio (%)

Standard capacity ratio Indoor units total capacity ratio (%)

2 Heating capacity calculation method :

Required heating capacity = Heating capacity x Factor (


Indoor air dry bulb temperature vs. capacity correction value

*1,

*2) kW

Capacity correction value

1.2 1.1 1.0 0.9 0.8 15

Capacity correction value

(Example) Design Indoor conditions : 21.5oC DB Capacity correction value : 0.98


1.2 1.1 1.0 0.9 0.8 15

20

24

Indoor air dry bulb temp. (oC)

20

24

Indoor air dry bulb temp. (oC)

Outdoor air wet bulb temperature vs. capacity correction value


Capacity correction value
1.2 1.1
1
Capacity correction value

(Example) Design Outdoor conditions : -5oC WB Capacity correction value : 0.8


1.2 1.1
1

0.9 0.8 0.7 0.6 0.5 -15 -10 -5 0 5


o

0.9 0.8 0.7 0.6 0.5 -15 -10 -5 0 5 10 15

10

15

Outdoor air wet bulb temp. ( C)

Outdoor air wet bulb temp. (oC)

*1 : Coefficient to use for correction of outdoor unit capacity when total capacity of the indoor units are not equal to the outdoor unit capacity. *2 : Refer to item 3.

1-19

Air flow variation ratio of indoor unit vs. capacity correction (For concealed duct type only)

Capacity correction value

1.1

1.0

0.9 80

90

100

110

120

Air flow variation ratio (%)

Connecting pipe length and lift difference between indoor and outdoor units vs. capacity correction value

Height of outdoor unit H (m)

97

96

95

30 20 10 0 -10 -20 0 10 20 30
100% 98

99

40

50

60

70

80

94

90

100

Pipe length (Equivalent length) L (m)

Outdoor unit
Height of outdoor unit H (m)

ho

Ll

L is the longest one of (Ll + a, Ll + b, Ll + c) H = ho + (Largest one of ha, hb, and hc)

(Example) Design Pipe length : 75m Heigh of outdoor unit : 15m Capacity correction value : 95.1%
97 96 95

30
99

20 10 0 -10 -20 0
100%

hc

hb

ha

a b c

A B Indoor unit C

10

20

98

30

40

50

60

70

80

94

90

100

Pipe length (Equivalent length) L (m)

1-20

Correction of outdoor unit diversity


(Example)
Capacity correction value
1.1 1 0.9 0.8 0.7 80 90 100 110 120 130

Design Outdoor unit Indoor units total capacity (Capacity ratio Capacity correction value
Capacity correction value
1.1 1 0.9 0.8 0.7 80 90 100 110

: 5HP : 4.5HP : 90%) : 0.9%

Standard capacity ratio Indoor units total capacity ratio (%)

120

130

Standard capacity ratio Indoor units total capacity ratio (%)

*1 : Coefficient to use for correction of outdoor unit capacity when total capacity of the indoor units are not equal to the outdoor unit capacity.

3 Capacity correction in case of frost on the outdoor heat exchanger in heating


Correct the heating capacity when frost was found on the outdoor heat exchanger. Heating capacity = Capacity after correction of outdoor unit Correction value of capacity resulted from frost (Capacity after correction of outdoor unit : Heating capacity calculated in the above item 2.)

Capacity correction in case of frost on the outdoor heat exchanger


Capacity correction value
1.0

0.9

0.8 -15

-10

-5

10

Outdoor air wet bulb temp. (oC)

4 Capacity calculation for each indoor unit


Capacity for each indoor unit = Capacity after correction of outdoor unit x Required standard capacity of indoor unit Total value of standard indoor unit capacity

1-21

5 Operating temperature range

In cooling time
45 40

In heating time
20 15 10 5 0 -5 -10 -15 -20

Outdoor air dry bulb temp. (oC)

35 30 25
Usable range (in pull down)

Outdoor air wet bulb temp. (oC)

20 15 10 5 0 -5 -10 10 15

Continuously operable range

Usable range (in warming-up)


5 10 15

Continuously operable range

20

25
o

28

30

20

25

30

Indoor air wet bulb temp. ( C)

Indoor air dry bulb temp. (oC)

6 Rated conditions
Cooling : Indoor air temperature 27oC DB/19.0oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

1-22

1-3-4. Example of equipment Selection

The following shows an example of equipment selection based upon a building model Fig. 1 Overview of building model <Outside view> <Floor plan>

Quiet places
8m

2F 2 - 1 2 - 2 2 - 3

2-4

2-5

2F
1-1 1-4 1-3

7. 2m

1F
10.4m

1F
1-2

Stores

Non-air conditioning zone

Steel frame, reinforced concrete building, two stories above ground. Total floor area : 150m2 Outdoor unit is installed on the roof. Design indoor conditions Cooling : 27.0/19.0OC DB/WB, Heating : 20OC DB Design outdoor conditions Cooling : 35OC DB (Standard condition), Heating : 3OC WB (Standard condition : 6OC WB)

Selection Criteria for Each Floor

2F : Outdoor capacity exactly matches the total indoor capacity.


Total indoor HP = Outdoor unit HP Indoor : 1.5 HP x 2 units + 1.25 HP + 1.0 HP+ 0.8HP = 6.05 HP Outdoor : 6 HP Same capacity

1F : Consider the increasing heat load in the specific room.


Total indoor units HP > Outdoor unit HP Select each indoor unit based on individual peak room load. Indoor : 1.0HP + 1.5HP + 2.0HP + 2.0HP = 6.5HP Outdoor : 6HP The outdoor unit should have sufficient capacity to cover the peak demand of the indoor unit

1-23

Procedure and result of equipment selection


1 Procedure of equipment selection
a. Calculate cooling for every rooms. b. Select an indoor unit to match the cooling load for every room from the table in pages. c. Choose a tentative outdoor unit that will match with the indoor units. Perform capacity correction based on the pipe length, system lift, indoor set temperature, outdoor temperature. Then, make sure the corrected system cooling capacity satisfies the cooling load.

2 Equipment selection and capacity check


Air conditioning load Indoor air conditioning load Room No. (kW) Cooling 2-1 2-2 2F 2-3 2-4 2-5 1-1 1-2 1F 1-3 1-4 5.1 5.1 4.9 3.7 MMU-AP0181H MMU-AP0181H 5.6 5.6 6.3 6.3 MAP0601H2D 4.2 3.3 2.6 2.3 4.1 2.6 4.1 Heating 3.4 2.2 2.5 2.3 4.0 2.3 3.8 Model MMU-AP0151H MMU-AP0121H MMU-AP0091H MMU-AP0071MH MMU-AP0151H MMU-AP0091H MMU-AP0151H Equipment selection Indoor unit Capacity (kW) Cooling 4.5 3.6 2.8 2.2 4.5 2.8 4.5 Heating 5.0 4.0 MAP0601H 3.2 MAP0601H2D 2.5 5.0 3.2 5.0 MAP0601H 15.5 18.0 15.5 18.0 Model MCYOutdoor unit Capacity (kW) Cooling Heating

Floor

Piping distance Floor Room No. Equivalent length (m) Height difference (m)

Capacity correction Pipe correction x temp. correction Cooling Heating

Capacity check after correction Capacity Capacity (kW) Cooling 4.3 Heating 4.4 3.5 2.8 2.4 4.4 2.9 4.5 5.6 5.6 good Judgment

2-1 2-2 2F 2-3 2-4 2-5 1-1 1-2 1F 1-3 1-4 42 5 1.0 x 1.0 x 1.03 x 0.92 =0.94= 1.0 x 0.95 x 0.975 x 1.03 x 0.95 =0.90= 23 1.0 x 1.0 x 0.96 =0.96= 1.0 x 0.95 x 0.99 x 0.95 =0.89=

3.4 2.6 2.4 4.3 2.6 4.2 5.2 5.2

1-24

3 Schematic diagram

MCY-MAP0601HT MCY-MAP0601HT2D

MCY-MAP0601HT MCY-MAP0601HT2D

Outdoor unit

1st branching 2nd branching joint joint

3rd branching joint

4th branching joint

PMV Kit RBM-PMV0901E MMU-AP0151H

PMV Kit RBM-PMV0361E MMU-AP0121H

PMV Kit RBM-PMV0361E MMU-AP0091H

PMV Kit RBM-PMV0361E MMU-AP0071MH

PMV Kit RBM-PMV0901E MMU-AP0151H

2-1

2-2

2- 3

2-4

2-5

MMU-AP0091H

MMU-AP0151H

MMU-AP0181H

MMU-AP0181H

1-1

1-2

1- 3

1-4

1-25

1-4. Piping requirement


1-4-1. Free branching system
Line branching system Header branching system 3 Header branching system after line branching 4 Line branching system after header branching 5 Header branching system after header branching The above five branching systems are available to dramatically increase the flexibility of refrigerant piping design.
2 1

Outdoor unit Branching joint

Line branching system


Indoor unit Remote controller

Outdoor unit

Header branching system


Indoor unit Remote controller

Branching header

* In case of "PMV Kit"

Outdoor unit

Header branching system after line branching

Branching joint

Branching header

PMV Kit Indoor unit Remote controller

* In case of "PMV Kit" Line branching system after header branching

Outdoor unit

Branching header

Header branching system after header branching

PMV Kit Indoor unit Remote controller

Branching joint

1-26

1-4-2. Refrigerant piping length and piping size


1

Allowable length and height difference of refrigerant piping

Outdoor unit

Main pipe

L1
Branching pipe

L2
Branching header

1st branching section

Branching pipe

L3
Height difference between Indoor and outdoor unit Indoor unit Height difference between indoor units

H1
Equivalent length corresponded to farthest piping

H2 L

Equivalent length corresponded to farthest piping after 1st branching Li

L4 e
Y-shape branching joint

1-27

Allowable length and height difference of refrigerant piping


Allowable value Piping section

Total extension of pipe (Liquid pipe, real length)

180m

L1+L2+L3+L4+ a+b+c+d+e+f+g

Real length Furthest piping length L (*1) Equivalent length Piping Length Max.equivalent length of main pipe Equivalent length of furthest piping from 1st branching Li (*1) Max.real length of indoor unit connecting pipe

100m L1+L3+L4+g 125m

65m

L1

35m

L3+L4+g

15m

a, b, c, d, e, f, g

Upper outdoor unit Height between indoor and outdoor units H1 Height Difference Lower outdoor unit

30m

20m

Height between indoor units H2

15m

*1 Furthest indoor unit from 1st branch to be named "A"

1-28

1-4-2. Refrigerant piping length and piping size


2

Selection of refrigerant piping

Outdoor unit

Gas pipe Main pipe

Liquid pipe 1st branching Branching section 1 4 2 pipe

Branching header 4

Indoor unit Branching Y-shape pipe Branching joint 4 2

Indoor unit

1-29

Selection of refrigerant piping


Name
Size of main pipe

No. Piping parts


Outdoor unit
1

Selection of pipe size

Outdoor unit capacity type

Gas pipe (mm) Liquid pipe (mm) 15.9 15.9 19.1 9.5 9.5 9.5

Main pipe 1st branching section

0401 type 0501 type 0601 type

Pipe size between branching sections

Branching section
2

Total capacity codes of indoor units at down stream side Equivalent to HP

Gas pipe (mm) 12.7 15.9 19.1

Liquid pipe (mm) 9.5 9.5 9.5

Branching pipe Branching section

Below 2.8 2.8 to below 6.4 6.4 to below 7.2

Note) If the total capacity code value of indoor units exceeds that of the outdoor units, apply the capacity code of outdoor units. Connecting pipe size of indoor unit

Branching section
3

Indoor unit connecting pipe

Indoor unit capacity type 007, 009, 012 type 015, 018 type 024, 030, 036, 048 type

Gas pipe (mm) Liquid pipe (mm) 9.5 12.7 15.9 6.4 6.4 9.5

Indoor unit

Selection of branching section Total capacity codes of indoor units at down stream side Equivalent to HP Model name RBM-BY53E RBM-BY103E RBM-HY1043E RBM-HY1083E

Y-shape branching joint


4

Y-shape branching joint Branching For 4 branches header For 8 branches

Below 6.4 6.4 to below 7.8 Below 7.8 Below 7.8

Branching section Branching header

Note) *1 : When using a Y-shape branching joint for the 1st branch, select according to capacity code of the outdoor unit. *2 : For 1 line after branching header indoor units with a maximum capacity code of 6.0 in total can be connected.

Minimum wall thickness for R410A application


Soft OK OK OK OK NG* Harf Hard or Hard OK OK OK OK OK OD (inch) 1/4" 3/8" 1/2" 5/8" 3/4" OD (mm) 6.35 9.52 12.70 15.88 19.05 Minimum wall thickness (mm) 0.80 0.80 0.80 1.00 1.00 *If the pipe size is O / 19.0 or more, use a suitable material.

1-30

1-4-3. Refrigerant piping length and piping size with PMV Kit
1

Allowable length and height difference of refrigerant piping

Outdoor unit

Main pipe

L1
Branching pipe

L2
Branching header

1st branching section

d
PMV Kit

Branching pipe

L3
Height difference between Indoor and outdoor unit

j
Indoor unit

H1

Height difference between indoor units (PMV Kit) H2 Equivalent length corresponded to farthest piping

L Li

Equivalent length corresponded to farthest piping after 1st branching

L4 e
Y-shape Branching joint

f m

g n

1-31

Allowable length and height difference of refrigerant piping


Allowable value Total extension of pipe (Liquid pipe, real length) Piping section L1+L2+L3+L4+ a+b+c+d+e+f+g+ h+i+j+k+l+m+n

150m

Real length Furthest piping length L (*1) Equivalent length Piping Length Max.equivalent length of main pipe Equivalent length of furthest piping from 1st branching Li (*1)

65m L1+L3+L4+g+n 80m

50m

L1

15m

L3+L4+g+n

Max.real length of indoor unit connecting pipe

15m

a+h, b+i, c+j, d+k, e+l, f+m, g+n

Real length between PMV Kit and indoor unit

2m or more and up to 10m

h, i, j, k, l, m, n

Upper outdoor unit Height between indoor and outdoor unit H1 Height Difference Lower outdoor unit Height between indoor units (PMV Kit) H2 Height difference between highest indoor unit or PMV Kit and lowest indoor unit or PMV Kit shall be 15m or less
*1 Furthest indoor unit from 1st branch to be named "A"

30m

20m

15m

Not Available
PMV Kit

Available
PMV Kit
Indoor unit Indoor unit

NOTE , Don t connect two or more indoor units to one PMV Kit. Arrange one indoor unit and one PMV Kit set to 1 by 1.

1-32

1-4-3. Refrigeran piping length and piping size with PMV Kit
2

Selection of refrigerant piping

Outdoor unit

Gas pipe Main pipe

Liquid pipe 1st branching Branching section 1 4 2 pipe

Branching header 4

5 3

5 3

5 3 3

Indoor unit

Y-shape Branching Branching joint pipe 4 2 2

PMV Kit

5 3

5 3

Indoor unit

1-33

Selection of refrigerant piping


Name
Size of main pipe

No. Piping parts


Outdoor unit
1

Selection of pipe size

Outdoor unit capacity type

Gas pipe (mm) Liquid pipe (mm) 15.9 15.9 19.1 9.5 9.5 9.5

Main pipe 1st branching section

0401 type 0501 type 0601 type

Pipe size between branching sections

Branching section
2

Total capacity codes of indoor units at down stream side Equivalent to HP

Gas pipe (mm) 12.7 15.9 19.1

Liquid pipe (mm) 9.5 9.5 9.5

Branching pipe Branching section

Below 2.8 2.8 to below 6.4 6.4 to below 7.2

Note) If the total capacity code value of indoor units exceeds that of the outdoor units, apply the capacity code of outdoor units. Connecting pipe size of indoor unit

Branching section
3

Indoor unit connecting pipe

Indoor unit capacity type 007, 009, 012 type 015, 018 type 024 type

Gas pipe (mm) Liquid pipe (mm) 9.5 12.7 15.9 6.4 6.4 9.5

Indoor unit

Selection of branching section Total capacity codes of indoor units at down stream side Equivalent to HP Model name RBM-BY53E RBM-BY103E RBM-HY1043E RBM-HY1083E

Y-shape branching joint


4

Branching section Branching header

Y-shape branching joint *1 Branching For 4 branches header For 8 branches *2

Below 6.4 6.4 to below 7.8 Below 7.8 Below 7.8

Note) *1 : When using a Y-shape branching joint for the 1st branch, select according to capacity code of the outdoor unit. *2 : For 1 line after branching header indoor units with a maximum capacity code of 6.0 in total can be connected.

Selection of PMV Kit Indoor unit capacity type Model name RBM-PMV0361E PBM-PMV0901E

PMV Kit

PMV Kit

007, 009, 012 type 015, 018, 024 type

Minimum wall thickness for R410A application


Soft OK OK OK OK NG* Harf Hard or Hard OK OK OK OK OK OD (inch) 1/4" 3/8" 1/2" 5/8" 3/4" OD (mm) 6.35 9.52 12.70 15.88 19.05 Minimum wall thickness (mm) 0.80 0.80 0.80 1.00 1.00 *If the pipe size is O / 19.0 or more, use a suitable material as detailed in the installation manual.

1-34

1-4-4. Refrigerant piping example


1

In case of without "PMV Kit"

Outdoor unit

MCY-MAP0601HT

L1 =60m pipe (7.6)

Main

Branching pipe

(3.4) L2 =7m

Branching header Capacity code

1st branching section 1

10m

Branching pipe

=1m

=6m

=8m

=15m

L3

=20m

(0.8)

(1.0)

(0.8)

(0.8)

MMU-AP0071MH MMU-AP0091H MMU-AP0701MH MMU-AP0701MH

Indoor unit

(4.2) e =4m (1.7)


Y-shape Branching joint
3

=10m

12m (2.5)

MMU-AP0151H MMU-AP0241H

1-35

Piping size Mark Equivalent length (m) Seclection method (capacity code) Gas pipe (mm) Liquid pipe (mm)

L1

60

O / 19.1

O / 9.5

L2

0.8 + 1.0 + 0.8 + 0.8 = 3.4

O / 15.9

O / 9.5

L3

20

1.7 + 2.5 = 4.2

O / 15.9

O / 9.5

0.8

O / 9.5

O / 6.4

1.0

O / 9.5

O / 6.4

0.8

O / 9.5

O / 6.4

15

0.8

O / 9.5

O / 6.4

1.7

O / 12.7

O / 6.4

10

2.5

O / 15.9

O / 9.5

Y-shape branching joint and Header Y-joint or Header select (capacity code) 6 (capacity code of outdoor unit) 0.8 +1.0 +0.8 +0.8 = 3.4 (a+b+c+d=L2) 1.7 + 2.5 = 4.2 (e+f=L3)

Mark

Model name

1st branching

RBM-BY53E

Branch header

RBM-HY1043E

Y-shape branch joint

RBM-BY53E

1-36

1-4-4. Refrigerant piping example


2

In cace of PMV Kit

Outdoor unit

MCY-MAP0601HT

L1 =20m pipe (7.6)

Main

Branching pipe

(3.4) L2 =3m

Branching header Capacity code

1st branching section 1

10m

Branching pipe

=4m

=3m

=6m

=7m

L3

=6m

(0.8)

(1.0)

(0.8)

(0.8)

MMU-AP0071MH MMU-AP0091H MMU-AP0701MH MMU-AP0701MH

Indoor unit

(4.2) e =4m (1.7)


Y-shape Branching joint
3

=6m

12m (2.5)

MMU-AP0151H

PMV Kit
MMU-AP0241H

1-37

Piping size Mark L1 L2 L3 a b c d e f Equivalent length (m) 20 3 6 4 3 6 7 4 6 0.8 + 1.0 + 0.8 + 0.8 = 3.4 1.7 + 2.5 = 4.2 0.8 1.0 0.8 0.8 1.7 2.5 Seclection method (capacity code) Gas pipe (mm)
O / 19.1 O / 15.9 O / 15.9 O / 9.5 O / 9.5 O / 9.5 O / 9.5 O / 12.7 O / 15.9

Liquid pipe (mm)


O / 9.5 O / 9.5 O / 9.5 O / 6.4 O / 6.4 O / 6.4 O / 6.4 O / 6.4 O / 9.5

Y-shape branching joint and Header Mark


1 2 3

Y-joint or Header select (capacity code) 6 (capacity code of outdoor unit) 0.8 +1.0 +0.8 +0.8 = 3.4 (a+b+c+d=L2) 1.7 + 2.5 = 4.2 (e+f=L3)

Model name RBM-BY53E RBM-HY1043E RBM-BY53E

1st branching Branch header Y-shape branch joint

PMV Kit Mark PMV Kit select (capacity code) 0.8 1.0 0.8 0.8 1.7 2.5 Model name RBM-PMV0361E RBM-PMV0361E RBM-PMV0361E RBM-PMV0361E RBM-PMV0901E RBM-PMV0901E

1-38

1-4-5. Charging requirement with additional refrigerant


After the system has been vacuumed,replace the vacuum pump with a refrigerant cylinder and charge the system with additional refrigerant.

R410A

Calculating the amount of additional refrigerant required


(Calculation) Additional refrigerant charge amount is calculated from size of liquid pipe at site and its real length.
Additional refrigerant charge + X amount per liquid pipe 1m (Table 1) Compensation by outdoor HP (Table 2)

Additional refrigerant Real length of R (kg) = charge amount at site liquid pipe

Table 1 Pipe dia. at liquid side Additional refrigerant amount/1m (kg) Table 2 Outdoor unit capacity type Compensation by outdoor HP (kg) Example : (0501 type)
L1 a L2 b L3 c d

O / 6.4

O / 9.5

0.025

0.055

0401 type -0.8

0501 type -0.4

0601 type 0

L1 b

O / 9.5 : 10m O / 6.4 : 3m

L2 c

O / 9.5 : 10m O / 6.4 : 4m

L3 d

O / 9.5 : 5m O / 6.4 : 5m

O / 9.5 : 3m

Additional charge amount R (kg) = (Lx X 0.025kg/m) + (Ly X 0.055kg/m) + (-0.4kg) = (12 X 0.025kg) + (28 X 0.055kg) + (-0.4kg) =1.44kg Lx : Real total length of liquid pipe O / 6.4 (m) Ly : Real total length of liquid pipe O / 9.5 (m) Note) If the additional refrigerant amount indicates a negative result from the calculation, use air conditioner without the adding of any additional refrigerant.

1-39

1-5. Wiring guideline


CAUTIONS
(1) Keep the refrigerant piping system and the indoor-indoor/indoor-outdoor control wiring systems together. (2) When running power supplies and control wires parallel to each other, run them through separate conduits or maintain a suitable distance between them. (Current capacity of power supplies: 10A or less for 300m, 50A or less for 500m)

1-5-1. General
Perform wiring of the power supplies in conformance with the regulation of the local electrical company. Use a 2 core shield wire for control wiring on connecting indoor units, and connecting of indoor units to outdoor units. This is recommended to prevent possible noise issues. Be sure to connect an earth leakage breaker to the power supply of the indoor units. Never connect 220-240V power to the control wiring terminal block (U1,U2,U3,U4). Fault will be caused. Locate wiring system for the control and refrigerant piping system in the same line. Arrange the cables so that the electrical wires do not come in to contact with high-temperature parts of the pipework ; otherwise insulation will melt and an accident may be caused. Do not turn on the power supply of the indoor units until vacuuming of the refrigerant pipe has finished.

1-5-2. Connection of power supply


The details are as follows. (Terminal block) (Stripping length power cable) 90 50

(Power cable clamp)

Power supply specifications

(Protective bush : Accessory)

Select the power supply cabling and fuse of each outdoor unit from the following specifications: 3 core cable in conformance with Design 60245 IEC 66 Do not connect the units looping via the terminal blocks (L,N)

1-40

1-5-3. Electrical wiring desin


Power supply MCY-MAP###1HT series MCY-MAP###1HT2D series 1N~ 50Hz 220V-240V 1N~ 60Hz 220V

Earth L N

Outdoor power source Earth leakage Breaker hand switch

Over current breaker breaker (fuse) switch Earth leakage breaker

Outdoor unit power supply

Pull box

Indoor power source


Single phase 50Hz 220-240V or 60Hz 220V Earth leakage breaker power switch Indoor unit Indoor unit Indoor unit

Indoor unit

Indoor unit

Indoor unit

Determine the wire size for the indoor unit according to the number of conncted indoor units downstream. Outdoor Unit capacities and power supply wire sizes (Reference) Observe local regulations in reference to the wire size selection and installtion.
Outdoor unit capacity type Wire size * Maxim running current Installation fuse

0401 type 0501 type 0601 type


* Desi gn 60245 IEC66

6 mm2 Max. 28 m 6 mm2 Max. 25 m 6 mm2 Max. 22 m

25A 28A 31A

32A 32A 40A

For Indoor Unit power supply (Must be independent from the outdoor unit power supply )
Item Model Power supply wiring Wire size Field fuse
2 2

All models of indoor units


NOTE:

2.0mm MAX.20m

3.5mm MAX.50m

15A

The above connecting lengths stated in the table indicate the length from the isolator to the outdoor unit. When the power supply of the indoor units are connected in parallel, it is assumed that no more than a 2% voltage drop will occur. If the connecting length is to exceed the stated lengths, select a suitable wire in accordance with the local wiring standards.

1-41

1-5-4. Design of control wiring

Power supply Single phase 220-240V 50Hz

(Open) Earth

220V

60Hz
Communication wire for control between outdoor unit and indoor unit Connection of shield wire must be connected (Connected to all connecting sections in each indoor unit) Communication wire for control between indoor and PMV Kit

Central remote controller (Option) TCB-SC642TLE2 (For line 64)

(Header) Remote controller

(Follower)

PMV Kit (option)

Communication wire for control between indoor and PMV Kit (option)

Control device
U1 U2 U3 U4

Mini-SMMS system A
Outdoor unit
U3 U4

Outdoor unit
U3 U4 U1 U2 U1 U2

Outdoor unit
U3 U4

Outdoor unit
U1 U2

B
U1 U2 U1 U2 A B U1 U2 A B

B
U1 U2 A B U1 U2 A B U1 U2 A B

B
U1 U2 A B U1 U2 A B

Indoor unit

A B

Remote controller

Remote controller

Remote controller

Wire specification, quantity, size of crossover wiring and remote controller wiring
Name Crossover wiring (A + B) (indoor-indoor / indoor-outdoor / control wiring, central control wiring) *Total Control wiring length Remote controller wiring Control wiring between indoor and PMV Kit Qty 2 cores 2 cores Up to 500m Size Up to 1000m 1000 to 2000m 2.0mm2 Specification Shield wire -

1.25mm2 0.5 to 2.0mm2

Be sure to use the attached cable. MIN 2m - MAX 10m

(1) The crossover wiring and central control wiring uses a 2-core non-polarity communication wire. Use 2-core shielded wire to prevent possible noise issues. Connect the end of the shielded wires and earth(ground) at both the outdoor and indoor unit. Where the shielded wire is connected between a central controller and a outdoor unit, only earth(ground) at one end of the central control line. (2) Use 2-core non-polarity wire for remote controller. (A, B terminals) Use 2-core non-polarity wire for wiring of group control. (A, B terminals)

1-42

1-5-5. Example of system wiring Design


1

In cace of without "PMV Kit"


Outdoor power supply MCY-MAP###1HT series : 1N~ 50Hz 220V-240V MCY-MAP###1HT2D series : 1N~ 60Hz 220V Central remote controller power supply 1N~ 50Hz 220-240V 1N~ 60Hz 220V Outdoor unit Indoor unit Remote controller Central remote controller (option) Over current breaker (fuse) switch Earth leakage breaker Main switch Pull box PMV Kit (option)

(Option) L N Earth U1 U2 U3 U4 (Open) (Open)


To other refrigerant system

Outdoor unit L N Earth Relay connector (At shipment from factory : No connection) U1 U2 U3 U4

Connection of shield wire must be connected (Connected to all connecting sections in each Indoor units) Control wiring between indoor units

Indoor unit U1 U2 A B control ad Eart h L N Eart h L N U1 U2 A B Eart h L N U1 U2 A B Earth L N U1 U2 A B

A B

A B

A B Remote controller [Group control]

Indoor unit power supply 1N~ 50Hz 220-240V 1N~ 60Hz 220V

1-43

1-5-5. Example of system wiring Design


2

In cace of "PMV Kit"


Outdoor power supply MCY-MAP###1HT series : 1N~ 50Hz 220V-240V MCY-MAP###1HT2D series : 1N~ 60Hz 220V Central remote controller power supply 1N~ 50Hz 220-240V 1N~ 60Hz 220V Outdoor unit Indoor unit Remote controller Central remote controller (option) Over current breaker (fuse) switch Earth leakage breaker Main switch Pull box PMV Kit (option)

(Option) L N Earth U1 U2 U3 U4 (Open) (Open)


To other refrigerant system

Outdoor unit L N Earth Relay connector (At shipment from factory : No connection) U1 U2 U3 U4

Connection of shield wire must be connected (Connected to all connecting sections in each Indoor units) Control wiring between indoor units

Indoor unit U1 U2 A B PMV Kit (option) Indoor control Indoor control PC board PC boad CN82 Eart h L N Eart h L N U1 U2 A B Eart h L N U1 U2 A B Earth L N U1 U2 A B

A B

A B

A B Remote controller [Group control]

Indoor unit power supply 1N~ 50Hz 220-240V 1N~ 60Hz 220V

1-44

1-5-6. Electrical characteristics Outdoor units


Model name MCY-MAP0401HT MCY-MAP0501HT MCY-MAP0601HT Nominal (V-Ph-Hz) 230-1-50 230-1-50 230-1-50 Voltage Range Min Max 198 264 198 264 198 264 Compressor Fan Motor RLA kW FLA 0.063 x 2 22.4 1.2 0.063 x 2 25.3 1.3 0.063 x 2 27.8 1.3

50Hz
Power Supply MCA ICF 25 32 28 32 31 40

Legend RLA : Rated Load Amps FLA : Full Load Amps kW : Fan Motor Rated Output (kW) NOTE : RLA is based on the following conditions. Indoor temperature : 27oCDB / 19oCWB Outdoor temperature : 35oCDB

MCA : Minimum Circuit Amps MOCP : Maximum Overcurrent Protection (Amps) ICF : Maximum Instantaneous Current Flow Start

Indoor units
Type 4-Way Air Discharge Cassette Type Model MMU-AP 0091 H MMU-AP 0121 H MMU-AP 0151 H MMU-AP 0181 H MMU-AP 0241 H MMU-AP 0271 H MMU-AP 0301 H MMU-AP 0361 H MMU-AP 0481 H MMU-AP 0071 MH MMU-AP 0091 MH MMU-AP 0121 MH MMU-AP 0151 MH MMU-AP 0181 MH MMU-AP 0071 WH MMU-AP 0091 WH MMU-AP 0121 WH MMU-AP 0151 WH MMU-AP 0181 WH MMU-AP 0241 WH MMU-AP 0271 WH MMU-AP 0301 WH MMU-AP 0481 WH*1 MMU-AP 0071 YH MMU-AP 0091 YH MMU-AP 0121 YH MMU-AP 0152 SH MMU-AP 0182 SH MMU-AP 0242 SH Nominal Voltage (V-Ph-Hz) 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 220-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 Voltage Range Min Max 264 198 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 Fan Motor kW FLA 0.20 0.060 0.20 0.060 0.22 0.060 0.24 0.060 0.28 0.060 0.28 0.060 0.40 0.060 0.68 0.090 0.93 0.090 0.060 0.060 0.060 0.060 0.060 0.36 0.053 0.36 0.053 0.36 0.053 0.37 0.039 0.37 0.039 0.53 0.053 0.53 0.053 0.053 0.54 0.092 1.33 0.022 0.28 0.022 0.28 0.022 0.28 0.030 0.40 0.030 0.42 0.030 0.71

50Hz
Power Supply MCA MOCP 0.25 15 15 0.25 15 0.28 15 0.30 15 0.35 15 0.35 15 0.50 15 0.85 15 1.16

Compact 4-Way Cassette (600 x 600) Type

2-Way Air Discharge Cassette Type

1-Way Air Discharge Cassette Type

0.45 0.45 0.45 0.46 0.46 0.66 0.66 0.68 1.67 0.35 0.35 0.35 0.49 0.53 0.88

15 15 15 15 15 15 15 15 15 15 15 15 15 15 15

*1 China market only

1-45

Indoor units
Type Concealed Duct Type Model MMD-AP 0071 BH MMD-AP 0091 BH MMD-AP 0121 BH MMD-AP 0151 BH MMD-AP 0181 BH MMD-AP 0241 BH MMD-AP 0271 BH MMD-AP 0301 BH MMD-AP 0361 BH MMD-AP 0481 BH MMD-AP 0071 SPH MMD-AP 0091 SPH MMD-AP 0121 SPH MMD-AP 0151 SPH MMD-AP 0181 SPH MMD-AP 0181 H MMD-AP 0241 H MMD-AP 0271 H MMD-AP 0361 H MMD-AP 0481 H MMC-AP 0151 H MMC-AP 0181 H MMC-AP 0241 H MMC-AP 0271 H MMC-AP 0361 H MMC-AP 0481 H MMK-AP 0071 H MMK-AP 0091 H MMK-AP 0121 H MMK-AP 0151 H MMK-AP 0181 H MMK-AP 0241 H MMK-AP 0072 H MMK-AP 0092 H MMK-AP 0122 H MML-AP 0071 H MML-AP 0091 H MML-AP 0121 H MML-AP 0151 H MML-AP 0181 H MML-AP 0241 H MML-AP 0071 BH MML-AP 0091 BH MML-AP 0121 BH MML-AP 0151 BH MML-AP 0181 BH MML-AP 0241 BH MMF-AP 0151 H MMF-AP 0181 H MMF-AP 0241 H MMF-AP 0271 H MMF-AP 0361 H MMF-AP 0481 H Nominal Voltage (V-Ph-Hz) 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 220-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50 Voltage Range Min Max 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 264 198 Fan Motor kW FLA 0.33 0.120 0.33 0.120 0.39 0.120 0.39 0.120 0.50 0.120 0.60 0.120 0.60 0.120 0.70 0.120 0.96 0.120 1.13 0.120 0.35 0.060 0.35 0.060 0.37 0.060 0.38 0.060 0.47 0.060 0.93 0.160 1.55 0.160 1.55 0.160 1.87 0.260 2.12 0.260 0.33 0.030 0.37 0.030 0.48 0.040 0.48 0.040 0.90 0.080 0.96 0.080 0.35 0.030 0.35 0.030 0.35 0.030 0.37 0.030 0.37 0.030 0.40 0.030 0.20 0.030 0.21 0.030 0.22 0.030 0.30 0.045 0.30 0.045 0.49 0.045 0.49 0.045 0.54 0.070 0.54 0.070 0.29 0.019 0.29 0.019 0.29 0.019 0.52 0.070 0.52 0.070 0.53 0.070 0.77 0.037 0.77 0.037 1.01 0.063 1.01 0.063 1.48 0.110 1.84 0.160

50Hz
Power Supply MCA MOCP 15 0.41 15 0.41 15 0.49 15 0.49 15 0.62 15 0.75 15 0.75 15 0.88 15 1.20 15 1.41 15 0.44 15 0.44 15 0.47 15 0.48 15 0.59 15 1.16 15 1.94 15 1.94 15 2.34 15 2.65 15 0.41 15 0.46 15 0.60 15 0.60 15 1.13 15 1.20 15 0.44 15 0.44 15 0.44 15 0.46 15 0.46 15 0.50 15 0.24 15 0.26 15 0.27 15 0.37 15 0.37 15 0.62 15 0.62 15 0.68 15 0.68 15 0.36 15 0.36 15 0.36 15 0.65 15 0.65 15 0.66 15 0.96 15 0.96 15 1.27 15 1.27 15 1.85 15 2.30

Slim Duct Type

Concealed Duct High Static Pressure Type

Under Ceiling Type

High Wall 1series Type

High Wall 2series Type Floor Standing Cabinet Type

Floor Standing Concealed Type

Floor Standing Type

1-46

1-5-6. Electrical characteristics Outdoor units


Model name MCY-MAP0401HT2D MCY-MAP0501HT2D MCY-MAP0601HT2D Nominal (V-Ph-Hz) 220-1-60 220-1-60 220-1-60 Voltage Range Min Max 198 242 198 242 198 242 Compressor Fan Motor RLA kW FLA 0.063 x 2 22.4 1.2 0.063 x 2 25.3 1.3 0.063 x 2 27.8 1.3

60Hz
Power Supply MCA MOCP ICF 25 32 28 32 31 40

Legend RLA : Rated Load Amps FLA : Full Load Amps kW : Fan Motor Rated Output (kW) NOTE : RLA is based on the following conditions. Indoor temperature : 27oCDB / 19oCWB Outdoor temperature : 35oCDB

MCA : Minimum Circuit Amps MOCP : Maximum Overcurrent Protection (Amps) ICF : Maximum Instantaneous Current Flow Start

Indoor units
Type 4-Way Air Discharge Cassette Type Model MMU-AP 0091 H MMU-AP 0121 H MMU-AP 0151 H MMU-AP 0181 H MMU-AP 0241 H MMU-AP 0271 H MMU-AP 0301 H MMU-AP 0361 H MMU-AP 0481 H MMU-AP 0071 MH MMU-AP 0091 MH MMU-AP 0121 MH MMU-AP 0151 MH MMU-AP 0181 MH MMU-AP 0071 WH MMU-AP 0091 WH MMU-AP 0121 WH MMU-AP 0151 WH MMU-AP 0181 WH MMU-AP 0241 WH MMU-AP 0271 WH MMU-AP 0301 WH MMU-AP 0071 YH MMU-AP 0091 YH MMU-AP 0121 YH MMU-AP 0152 SH MMU-AP 0182 SH MMU-AP 0242 SH Nominal Voltage (V-Ph-Hz) 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 Voltage Range Min Max 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 Fan Motor kW FLA 0.21 0.060 0.21 0.060 0.23 0.060 0.25 0.060 0.29 0.060 0.29 0.060 0.42 0.060 0.70 0.090 0.98 0.090 0.060 0.060 0.060 0.060 0.060 0.38 0.053 0.38 0.053 0.38 0.053 0.44 0.039 0.44 0.039 0.61 0.053 0.61 0.053 0.67 0.053 0.30 0.022 0.30 0.022 0.30 0.022 0.40 0.030 0.45 0.030 0.75 0.030

60Hz
Power Supply MCA MOCP 15 0.26 15 0.26 15 0.29 15 0.31 15 0.37 15 0.37 15 0.52 15 0.88 15 1.22

Compact 4-Way Cassette (600 x 600) Type

2-Way Air Discharge Cassette Type

1-Way Air Discharge Cassette Type

0.47 0.47 0.47 0.55 0.55 0.76 0.76 0.84 0.37 0.37 0.37 0.50 0.57 0.94

15 15 15 15 15 15 15 15 15 15 15 15 15 15

1-47

Indoor units
Type Concealed Duct Type Model MMD-AP 0071 BH MMD-AP 0091 BH MMD-AP 0121 BH MMD-AP 0151 BH MMD-AP 0181 BH MMD-AP 0241 BH MMD-AP 0271 BH MMD-AP 0301 BH MMD-AP 0361 BH MMD-AP 0481 BH MMD-AP 0071 SPH MMD-AP 0091 SPH MMD-AP 0121 SPH MMD-AP 0151 SPH MMD-AP 0181 SPH MMD-AP 0181 H MMD-AP 0241 H MMD-AP 0271 H MMD-AP 0361 H MMD-AP 0481 H MMC-AP 0151 H MMC-AP 0181 H MMC-AP 0241 H MMC-AP 0271 H MMC-AP 0361 H MMC-AP 0481 H MMK-AP 0071 H MMK-AP 0091 H MMK-AP 0121 H MMK-AP 0151 H MMK-AP 0181 H MMK-AP 0241 H MMK-AP 0072 H MMK-AP 0092 H MMK-AP 0122 H MML-AP 0071 H MML-AP 0091 H MML-AP 0121 H MML-AP 0151 H MML-AP 0181 H MML-AP 0241 H MML-AP 0071 BH MML-AP 0091 BH MML-AP 0121 BH MML-AP 0151 BH MML-AP 0181 BH MML-AP 0241 BH MMF-AP 0151 H MMF-AP 0181 H MMF-AP 0241 H MMF-AP 0271 H MMF-AP 0361 H MMF-AP 0481 H Nominal Voltage (V-Ph-Hz) 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 220-1-60 Voltage Range Min Max 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 242 198 Fan Motor kW FLA 0.35 0.120 0.35 0.120 0.41 0.120 0.41 0.120 0.52 0.120 0.63 0.120 0.63 0.120 0.73 0.120 1.00 0.120 1.18 0.120 0.32 0.060 0.32 0.060 0.36 0.060 0.37 0.060 0.44 0.060 1.06 0.160 2.07 0.160 2.07 0.160 2.38 0.260 2.60 0.260 0.35 0.030 0.39 0.030 0.50 0.040 0.50 0.040 0.94 0.080 1.00 0.080 0.37 0.030 0.37 0.030 0.37 0.030 0.39 0.030 0.39 0.030 0.030 0.40 0.030 0.21 0.030 0.22 0.030 0.23 0.045 0.29 0.045 0.29 0.045 0.51 0.045 0.51 0.070 0.61 0.070 0.61 0.019 0.31 0.019 0.31 0.019 0.31 0.070 0.53 0.070 0.53 0.070 0.59 0.037 0.77 0.037 0.77 0.063 1.04 0.063 1.04 0.110 1.58 0.160 2.01

60Hz
Power Supply MCA MOCP 15 0.43 15 0.43 15 0.51 15 0.51 15 0.65 15 0.78 15 0.78 15 0.91 15 1.25 15 1.48 15 0.41 15 0.41 15 0.45 15 0.47 15 0.56 15 1.32 15 2.59 15 2.59 15 2.98 15 3.25 15 0.43 15 0.48 15 0.63 15 0.63 15 1.18 15 1.25 15 0.46 15 0.46 15 0.46 15 0.48 15 0.48 15 0.50 15 0.26 15 0.27 15 0.29 15 0.36 15 0.36 15 0.63 15 0.63 15 0.76 15 0.76 15 0.39 15 0.39 15 0.39 15 0.66 15 0.66 15 0.73 15 0.96 15 0.96 15 1.29 15 1.29 15 1.97 15 2.52

Slim Duct Type

Concealed Duct High Static Pressure Type

Under Ceiling Type

High Wall 1series Type

High Wall 2series Type Floor Standing Cabinet Type

Floor Standing Concealed Type

Floor Standing Type

1-48

2. Indoor Units

2-1. 4-way Air Discharge Cassette type....................................2-2


2-5 2-2. Compact 4-way Cassette (600 x 600) type.......................2-7 2-11 2-3. 2-way Air Discharge Cassette type..................................2-8 2-13 2-4. 1-way Air Discharge Cassette type..................................2-17 2-17 2-5. Concealed Duct Standard type...........................................2-23 2-22 2-6. Slim Duct type........................................................................2-30 2-29 2-7. Concealed Duct High Static Pressure type.....................2-38 2-33 2-8. Under Ceiling type.................................................................2-43 2-36 2-9. High Wall 1series type..........................................................2-47 2-41 2-10. High Wall 2series type..........................................................2-53 2-57 2-11. Floor Standing Cabinet type............................................2-44 2-47 2-12. Floor Standing Concealed type.........................................2-61 2-65 2-13. Floor Standing type............................................................2-50 2-70 2-14. Application controls of indoor unit.................................2-54

2-1

2-1. 4-way Air Discharge Cassette Type


Apperarance

Standard accessories
Part name
Installation Manual

Q'ty
2

Shape
_

Use
(Be sure to hand over to customer)

Part name
Heat insulator

Q'ty
1

Shape

Use
For heat insulating of drain connecting section

Heat insulating pipe Installation pattern

For heat insulating of pipe connecting section

Washer

For hanging down unit

For confirmation of ceiling opening and main unit position

Hose band

For connecting drain pipe

Installation gauge

For positioning of ceiling position (united with installation pattern)

Flexible hose

For centering the drain pipe

Pattern fixing screw

M5 x 16

For attaching pattern

Heat insulator

For sealing the wire connection opening

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21U(W)-E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-2

2-1. 4-way Air Discharge Cassette Type


Optional accessories
Air discharge direction kit Auxiliary fresh air Flange TCB-FF101URE2 Super Long Life Filter TCB-LF1601UE2 TCB-BC1601UE High Efficiency Filter 65 TCB-UFM1601UE High Efficiency Filter 90 TCB-UFH1601UE Fresh air inlet Box TCB-GB1601UE2 Fresh air and Filter Chamber TCB-GFC1601UE2 Spacer for height adjustment TCB-SP1601UE

Ceiling panel RBC-U21PG(W)-E2

Parts Name Ceiling panel

Model name RBC-U21PG(W)-E2

Applied Model

Notes Required accessory Dust collecting effect : 50% (Weight method) *Not valid in combination with TCB-FM1601UE, TCB-UFH1601UE and TCB-BC1601UE Dust collecting effect : 65% (NBS Colorimentric method) *Not valid in combination with TCB-LF1601UE2, TCB-UFH1601UE, TCB-FF101URE2 and TCB-BC1601UE Dust collecting effect : 90% (NBS Colorimentric method) *Not valid in combination with TCB-LF1601UE2, TCB-UFM1601UE, TCB-FF101URE2 and TCB-BC1601UE For fresh air intake by using the knockout hole of Fresh air and filter chamber. (dia=100mm) *Not valid in combination with TCB-FF101URE2 and TCB-SP1601UE For fresh air intake and installing high efficiency filter or super long filter *Not valid in combination with TCB-SP1601UE For easy fresh air intake by using the knockout hole of indoor unit.(dia=100mm) *Not valid in combination with TCB-GB1601UE2 Height = 500mm *Not valid in combination with TCB-GB1601UE2 and TCB-GFC1601UE2 Air direction charge by cutting off air discharge port (3pcs) *Not valid in combination with TCB-LF1601UE2, TCB-UFM1601UE, TCB-UFH1601UE

Remarks

Super Long Life Filter

TCB-LF1601UE2

Use with TCB-GFC1601UE2

High Efficiency Filter 65

TCB-UFM1601UE

Use with TCB-GFC1601UE2

High Efficiency Filter 90

TCB-UFH1601UE

Use with TCB-GFC1601UE2

Fresh air inlet Box

TCB-GB1601UE2

MMU-AP***1H

Use with TCB-GFC1601UE2

Frech air and Filter Chamber

TCB-GFC1601UE2

Auxiliary fresh air Flange

TCB-FF101URE2

Spacer for height adjustment

TCB-SP1601UE

Air discharge direction kit

TCB-BC1601UE

2-3

50Hz

2-1. 4-way Air Discharge Cassete Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Starting current Main unit Appearance Ceiling Panel Model Panel color Height (mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg) 20 22 4.5 Finned tube (A) (kW) (A) MMU(kW) AP0091H 2.8/3.2 AP0121H 3.6/4.0 AP0151H 4.5/5.0 AP0181H 5.6/6.3 AP0241H 7.1/8.0 AP0271H 8.0/9.0 AP0301H 9.0/10.0 AP0361H 11.2/12.5 AP0481H 14.0/16.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) 0.17 0.020 0.30 0.19 0.022 0.33 0.21 0.026 0.36 0.24 0.032 0.42 0.35 0.048 0.59 0.59 0.070 0.87 0.81 0.110 1.23

Heat-insulating material attached Zinc hot dipping steel plate RBC-U21PG (W)-E2 Moon white (Munsell/2.5GY 9.0/0.5) 256 840 840 35 950 950 23 28 319

Main unit

Width Depth

Outer dimension Ceiling panel

Height Width Depth Main unit

Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid/Low) Motor Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4 O / 12.7

Non-flammable insulation

Turbo fan
(m3/h) (W) 800 (730/680) 930 (830/790) 1,050 (920/800) 60 Standard filter attached (Long life filter) Remote controller
O / 15.9 O / 9.5

1,200 (920/820)

1,320 (1,110/850)

1,680 (1,300/1,070) 90

2,040 (1,430/1,130)

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 30/29/27 31/29/27

25 (Polyvinyl chloride tube) 32/29/28 34/31/28 37/33/30 40/36/33 44/38/34

Not available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-4

2-1. 4-way Air Discharge Cassete Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply (A) Running current Electrical characteristics Power consumption (kW) Starting current Main unit Appearance Ceiling Panel Model Panel color Height Main unit Width Depth Outer dimension Ceiling panel Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid./Low) Motor Air filter Controller Gas side Connecting Liquid side pipe (mm) (mm)
O / 9.5 O / 6.4 O / 12.7

60Hz

MMU(kW)

AP0091H 2.8/3.2

AP0121H 3.6/4.0

AP0151H 4.5/5.0

AP0181H 5.6/6.3

AP0241H 7.1/8.0

AP0271H 8.0/9.0

AP0301H 9.0/10.0

AP0361H 11.2/12.5

AP0481H 14.0/16.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) 0.18 0.020 0.30 0.20 0.022 0.33 0.22 0.026 0.36 0.26 0.032 0.42 0.37 0.048 0.59 0.61 0.070 0.87 0.85 0.110 1.23

(A)

Heat-insulating material attached

Zinc hot dipping steel plate

RBC-U21PG (W) -E2 Moon white (Munsell/2.5GY 9.0/0.5) 256 840 840 35 950 950 20 22 4.5 Finned tube Non-flammable insulation Turbo fan (m3/h) (W) 800 (730/680) 930 (830/790) 1,050 (920/800) 60 Standard filter (Long life filter) Remote controller
O / 15.9 O / 9.5

(mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg)

319

23

28

1,200 (920/820)

1,320 (1,110/850)

1,680 (1,300/1,070) 90

2,040 (1,430/1,130)

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid./Low) PMV Kit (dB(A)) 30/29/27 31/29/27

25 (Polyvinyl chloride tube) 32/29/28 34/31/28 Not available 37/33/30 40/36/33 44/38/34

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-5

2-1. 4-Way Air Discharge Cassete Type


Dimension
MMU-AP0091H to P0481H
415 Suction grille (Air suction port) Electric parts box Air discharge port (4-way)

346.5 790 hanging bolt pitch 950 panel external dimension

35

381.6 723 hanging bolt pitch

860 to 910 ceiling open dimension

950 panel external dimension

97 B

210

35

105

For branch duct knockout square hole O / 150 (2 positions at right side) Hanging bolt Refrigerant pipe M10 or W3/8 local arrange connecting port 840 840 (Gas) 480 250 70 Refrigerant pipe Drain discharge port 270 227 connecting port 105 (Liquid)

130

88

30

45 113 174

860 to 910 ceiling open dimension

254.5

Bottom face of ceiling

Bottom face of ceiling


360

Model AP0091H to AP0301H AP0361H to AP0481H

A 256 319

mm B 120 183

Stand-up 640 or less

Stand-up 850 or less

15 or more

18

1000 or more

15 or more 200

Bottom face of ceiling

64

Knockout for flesh air intake For O / 100

(NOTE) As ABS is used for the drain discharge port of the main unit, the vinyl chloride paste cannot be used. Use the flexible hose (Band fix) included in the package.

Z view Wired remote controller 4 RBC-AMT31E


2.7

Drain-up standing-up size

Space required for installation and servicing

200

Simple wired remote controller RBC-AS21E2


120

Wireless remote controller kit TCB-AX21U(W)-E2


16 Weekly timer application 120 RBC-AMT31E and RBC-EXW21E2

Check port ( 450) Check port ( 450)

1000 or more

.5 57 5 2

57
Indoor unit

1000 or more

Bottom face of ceiling

Note: All dimensions are in mm.

2-6

2-2. Compact 4-way cassette (600 x 600) type


Appearance

Standard accessories
Part name
Installation Manual Heat insulating pipe Installation pattern Installation gauge Pattern fixing screw Heat insulator Washer Hose band Flexible hose Heat insulator

Q'ty
1 2 1 2 4 1 8 1 1 1

Shape
This manual (Ensure handover to customer)

Usage
For heat insulation of the pipe connecting section

For checking of ceiling opening and the main unit position For positioning of the ceiling position (To be used with the installation pattern)

M5 x 16

For attach the installation pattern For heat insulation of drain connecting section For hanging unit For connecting drain pipe For adjusting core-out of drain pipe For sealing of wire connecting port

Optional accessories
Air discharge direction kit

Auxiliary fresh air Flange TCB-FF101URE2 Fresh air inlet Box ********* Fresh air Chamber ********* Spacer for height adjustment ********* Ceiling panel RBC-UM11PG(W)E

Parts Name Ceiling panel Auxiliary fresh air Flange Frech air and Filter Chamber Fresh air inlet Box Spacer for height adjustment Air discharge direction kit

Model name RBC-UM11PG(W)E TCB-FF101URE2 TBD TBD TBD TBD

Applied Model

Notes Required accessory For easy fresh air intake by using the knockout hole of indoor unit.(dia=100mm)

Remarks

MMU-AP***1MH This product is scheduled to go on sale

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-7

2-2. Compact 4-way Cassette (600x 600) Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Main unit Appearance Ceiling Panel Model Panel color Height Main unit Width Depth Outer dimension Ceiling panel Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid/Low) Motor Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4

50Hz

MMU(kW)

AP0071MH 2.2/2.5

AP0091MH 2.8/3.2

AP0121MH 3.6/4.0

AP0151MH 4.5/5.0

AP0181MH 5.6/6.3

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (A) 0.28 0.034 0.49 0.30 0.036 0.52 0.31 0.038 0.54 0.34 0.041 0.59 0.42 0.052 0.73

Electrical characteristics

Zinc hot dipping steel plate *Heat-insulating material attached to only upper plate RBC-UM11PG(W)E Moon white (Munsell/2.5GY 9.0/0.5) 268 575 575 27 700 700 17 3 Finned tube

(mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg)

Non-flammble insulation Turbo fan (m3/h)

552/462/378

570/468/378

594/504/402 60 Long life filter Remote controller

660/552/468

762/642/522

(W)

O / 12.7

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 36/32/28 37/33/28

25 (Polyvinyl choride tube) 37/33/29 Available 40/35/30 44/39/34

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-8

2-2. Compact 4-way Cassette (600x 600) Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Main unit Appearance Ceiling Panel Model Panel color Height Main unit Width Depth Outer dimension Ceiling panel Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid/Low) Motor Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4

60Hz

MMU(kW)

AP0071MH 2.2/2.5

AP0091MH 2.8/3.2

AP0121MH 3.6/4.0

AP0151MH 4.5/5.0

AP0181MH 5.6/6.3

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (A) 0.27 0.034 0.49 0.29 0.036 0.52 0.30 0.038 0.54 0.33 0.041 0.59 0.41 0.052 0.73

Electrical characteristics

Zinc hot dipping steel plate *Heat-insulating material attached to only upper plate RBC-UM11PG(W)E Moon white (Munsell/2.5GY 9.0/0.5) 268 575 575 27 700 700 17 3 Finned tube

(mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg)

Non-flammble insulation Turbo fan (m3/h)

552/462/378

570/468/378

594/504/402 60 Long life filter Remote controller

660/552/468

762/642/522

(W)

O / 12.7

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 36/32/28 37/33/28

23 (Polyvinyl choride tube) 37/33/29 40/35/30 44/39/34

Available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-9

2-2. Compact 4-way Cassette (600 x 600) Type


Dimension
MMU-AP0071MH, AP0091MH, AP0121MH, AP0151MH, AP0181MH

Bottom face of ceiling


105 93 145.5

For bracch duct knockout square hole O / 150 Bottom face of ceiling O / 162 Electric parts box

70.5

207 175 Knockout for flesh air intake O / 100 149 29 64

235

105

235

575 unit external dimension

595 to 660 ceiling open dimension

575 unit external dimension

700 Panel external dimension

525 hanging bolt pitch

320.5

Model name

MMU-AP0071MH MMU-AP0091MH MMU-AP0121MH MMU-AP0151MH MMU-AP0181MH

Refrigerant pipe (Gas) 0151, 0181MH................. O / 12.7 0071, 0091, 0121MH....... O / 9.5 Refrigerant pipe (Liquid) O / 6.4
105 70.5

177 525 hanging bolt pitch 595 to 660 ceiling open dimension 700 Panel external dimension 97.5 214 105 42 148 256 O / 162

331.5

4-way air Discharge Cassete Type

Arialb1i0c0p34;TOSHIBA CARRIER CORPORATION

Hanging bolt M10 or W3/8 local arrange Drain discharge port

190.5

193.5

93

55

145.5

134

63

220.5

268

For branch duct knockout square hole O / 150

142

Ceiling panel

27

Wiring connection port

21 158

120

Bottom face of ceiling

300
Stand-up 827.5 or less Stand-up 850 or less

(NOTE) As ABS is used for the drain discharge port of the main unit, the vinyl chloride paste cannot be used. Use the flexible hose (Band fix) included in the package.

Indoor unit

595 to 660 ceiling open dimension

Bottom face Drain-up standing-up size of ceiling

368.5

64

142

Check port ( 450)

1000 or more

15 or more

595 to 660 ceiling open dimension

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2

Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

Obustacle
Space required for installation and servicing

Note: All dimensions are in mm.

2-10

15 or more

1000 or more

1000 or more

200

2-3. 2-way Air Discharge Cassette Type


Apperarance

Standard accessories
Part name
Installation Manual

Q'ty
1

Shape
This manual

Use
(Be sure to hand this over to customer) For heat insulating pipe connecting section For checking the position of the ceiling openings and the unit

Part name
Installation gauge

Q'ty
1

Shape

Use
For positioning of ceiling position (United with installation pattern)

Heat insulating pipe MMU-AP0301WH type or lower MMU-AP0481WH type

Pattern fixing screw

M5 x 16

For attaching the installation pattern For changing fan motor r.p.m. to apply higher ceiling For seal for wire connecting port

Installation pattern

1 _ 2

Fan motor connector

Heat insulator

Ceiling panel components


Name Ceiling panel Center panel Air filter Screw installing panel Screw installing panel

Shape (Q'ty)
(1 set) (1 pc) _ RBC-UW466PG : Attached to indoor unit

20mm
M5 x 20 (4 pcs)

30mm
M5 x 30 (2 pcs) For tentative hanging and fixing ceiling panel (Center part)

Usage

Attached to ceiling panel, For fixing ceiling panel and removes dust. (4 corners)

Optional accessories

Ceiling panel RBC-UW136PG RBC-UW266PG RBC-UW466PG

Parts Name Ceiling panel

Model name RBC-UW136PG RBC-UW266PG

Applied Model MMU-AP0071WH/0091/0121WH

Notes Required accessory

Remarks

MMU-AP0151/0181/0241/0301WH

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-11

2-3. 2-way Air Discharge Cassette Type


Specifications (50Hz)
Model name Cooling/Heating capacity Power supply Running current Electrical characteristics Power consumption Power factor Starting current Main unit Appearance Ceiling Panel Model Panel color Height Main unit Width Depth Outer dimension Ceiling panel Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid/Low) Motor Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4

50Hz

MMU- AP0071WH AP0091WH AP0121WH AP0151WH AP0181WH AP0241WH AP0271WH AP0301WH (kW) 2.2/2.5 2.8/3.2 3.6/4.0 4.5/5.0 5.6/6.3 7.1/8.0 8.0/9.0 9.0/10.0

AP0481WH China only 14.0/16.0 1 Phase 50Hz 220V

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.31 0.070 0.32 0.072 0.46 0.105 0.47 0.106

1.16 0.250 98

97 0.47 0.60

99 0.89
0.98

1.33

Heat-insulating material attached Zinc hot dipping steel plate RBC-UW136PG RBC-UW266PG Light ivory (Munsell 10Y 9/0.5) 398 830 550 8 1,000 650 33 8 Finned tube Non-flammable insulation Centrifugal fan (m3/h) (W) 1260/1140/960 1920/1500/1050 92 44 11 48 1,520 1,898 680 52 18 1,350 406 1,650 620 RBCUW466PG

(mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg)

570/510/450 53

780/700/600 39

1140/960/720 53

Standard filter attached (Long life filter) Remote controller


O / 12.7 O / 15.9 O / 9.5

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 34/32/30

25 (Polyvinyl chloride tube) 35/33/30 Not available 38/35/33 40/37/34 45/42/39

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-12

2-3. 2-way Air Discharge Cassette Type


Specifications (60Hz)
Model name Cooling/Heating capacity Power supply Running current Power Electrical characteristics consumption Power factor Starting current Main unit Appearance Model Panel color Height (mm) Main unit Outer dimension Ceiling panel Width (mm) 830 550 8 1,000 650 33 8 Finned tube Non-flammable insulation Centrifugal fan (m3/h) (W) 570/510/450 53 780/700/600 39 Standard filter (Long life filter) Remote controller Gas side Connecting Liquid side pipe (mm) (mm)
O / 9.5 O / 6.4 O / 12.7 O / 15.9 O / 9.5

60Hz

MMU(kW)

AP0071WH 2.2/2.5

AP0091WH 2.8/3.2

AP0121WH 3.6/4.0

AP0151WH 4.5/5.0

AP0181WH 5.6/6.3

AP0241WH 7.1/8.0

AP0271WH 8.0/9.0

AP0301WH 9.0/10.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.33 0.070 97 0.46 0.38 0.076 90 0.59 Heat-insulating material attached RBC-UW136PG 0.53 0.115 99 0.87 Zinc hot dipping steel plate RBC-UW266PG Light ivory (Munsell 10Y 9/0.5) 398 1.350 0.58 0.123 96 0.96

Ceiling panel

Depth (mm) Height (mm) Width (mm)

1,520

Depth (mm) Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid./Low) Motor Air filter Controller (kg) (kg)

44 11

48

1,140/960/720 53

1,260/1,140/960

Drain port (Nominal dia.mm) Sound pressure level(Note 2) (dB(A)) (High/Mid./Low) PMV Kit 34/32/30

25 (Polyvinyl chloride tube) 35/33/30 Not available 38/35/33 40/37/34

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-13

2-3. 2-way Air Discharge Cassette Type


Dimension
MMU-AP0071WH, AP0091WH, AP0121WH
Z view
Center of main unit 35 Center of panel Electric parts box 95 Air discharge port (2-way) 1000 Air suction port (2-way)

Hanging bolt pitch 480 Unit external dimension 550 Ceiling open dimension 620 Panel external dimension 650

30 Unit external dimension 830 Hanging bolt pitch 880 Ceiling open dimension 960 Panel external dimension 1000

5mm or more Ceiling 1000 or more Obstruction 1000 or more 1000 or more
0 20

265

Hanging bolt 4-M10 procured locally

398

222

Space required for installation and servicing


160mm or less

Ceiling panel (Procured locally)

156

Bottom face of ceiling

Branch duct knockout hole (also on opposite side)

100mm or less Indoor unit

508mm or less

Bottom face of ceiling

Refrigerant pipe connecting port (Gas side O / 9.5) 100 Refrigerant pipe connecting port (Liquid side O / 6.4)

Drain pipe connecting port Inner O / 32, Nominal O / 25 for vinyl chloride pipe 56 75 55 Pour water port

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

35 210 Power supply connecting port

35

78

Knockout hole for taking-in air (Only at reverse side)

Note: All dimensions are in mm.

2-14

178 242 282 348

150

53

60

650

MMU-AP0151WH, AP0181WH, AP0241WH, AP0271WH. AP0301WH

Z view
Center of main unit 35 Center of panel Electric parts box 95
Unit external dimension 550 Ceiling open dimension 620 Panel external dimension 650 Hanging bolt pitch 480

Air discharge port (2-way)

Air suction port (2-way)

30 Unit external dimension 1350 Hanging bolt pitch 1400 Ceiling open dimension 1480 Panel external dimension 1520

5mm or more

295
0 20

Hanging bolt 4-M10 procured locally

398

Ceiling

Obstruction

1000 or more

1000 or more

Space required for installation and servicing

Ceiling panel (Procured locally)

156

1000 or more

222

Bottom face of ceiling

Branch duct knockout hole (Also on opposite side)


160mm or less 508mm or less

100mm or less

Bottom face of ceiling

Refrigerant pipe connecting port (Gas side O / B) 56 Refrigerant pipe connecting port 100 (Liquid side O A)

Drain pipe connecting port Inner O / 32, Nominal O / 25 for vinyl chloride pipe 75 55 Pour water port

35

35

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

210 Power supply connecting port

78

Knockout hole for air intake (Only at reverse side) A


O / 6.4 O / 9.5

Model MMU-AP0151WH to AP0181WH MMU-AP0241WH to AP0301WH

Note: All dimensions are in mm.

2-15

178 242 282 348

150

53

60

B
O / 12.7 O / 15.9

650

MMU-AP0481WH*CHINA market only


Z view
Center of main unit 95 5 Center of panel Electric parts box 105
Unit external dimension 620 Ceiling open dimension 650 Panel external dimension 680

Air discharge port (2-way) 1898


Hanging bolt pitch 510

Air suction port (2-way)

Unit external dimension 1650 Hanging bolt pitch 1700 Ceiling open dimension 1850 Panel external dimension 1898 Hanging bolt 4-M10 procured locally

5mm or more

455
2 00

150
2 00

406

1000 or more Ceiling 1000 Obstruction or more 1000 or more

230 166

60

Space required for installation and servicing

Ceiling panel (Procured locally)

Bottom face of ceiling

Branch duct knockout hole (Also on reverse side)

160mm or less

516mm or less

100mm or less

Refrigerant pipe connecting port (Gas side O / 15.9) Refrigerant pipe 56 connecting port (Liquid side O 9.5) 100

Drain pipe connecting port (VP25) 75 55 Pour water port


50 1

210 Power supply Knockout hole for air intake connecting port (Only at reverse side)

Wired remote controller (RBC-AMT21E)


4
2.7

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit 16 120 TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2 Note: All dimensions are in mm.
120

2-16

86

Bottom face of ceiling

15

15

186 250 290 356

68

680

2-4. 1-way Air Discharge Cassette Type


Apperarance

Standard accessories
Part name
Installation Manual Installation pattern Installation gauge Pattern fixing screw Heat insulating pipe Washer Hose band Flexible hose Heat insulator Heat insulator Heat insulator

Q'ty
1 1 1 4 2 8 1 1 1 1 1

Shape
This manual _

Usage
(Be sure to hand this over to customer) For check of ceiling opening and unit position For check of ceiling opening and unit position (Unit with installation pattern)

M5 x 16

For mounting of pattern For insulating pipe connecting section

M10 x O / 34

For hanging-down of unit For connecting drain pipe For For insulating drain connecting section For sealing of pipe connecting port (With slit) For sealing of pipe connecting port (Without slit)

Optional accessories

Front air discharge unit TCB-BU21HWE

Auxiliary fresh air Flange TCB-FF101URE2

Ceiling panel RBC-US21PGE


Parts Name Ceiling panel Front air discharge unit Auxiliary fresh air Flange Model name RBC-US21PGE TCB-BUS21HWE MMC-AP0152SH/0182SH/0242SH TCB-FF101URE2 For easy fresh air intake by using the knockout hole of indoor unit.(dia=100mm) Applied Model Notes Required accessory Remarks

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-17

2-4. Compact 1-way Air Discharge Cassette Type


Apperarance

Standard accessories
Part name
Installation Manual

Q'ty
1

Shape
This manual

Use
(Be sure to hand this over to customer)

Part name
Installation gauge

Q'ty
1

Shape

Use
For positioning of ceiling position (United with installation pattern)

Heat insulating pipe

For heat insulating pipe connecting section

Pattern fixing screw

M5 x 16L

For attaching the installation pattern

MMU-AP0301WH type or lower Installation pattern

1 _ For checking the position of the ceiling openings and the unit

Fan motor connector

For changing fan motor r.p.m. to apply higher ceiling For seal for wire connecting port

MMU-AP0481WH type

insulator

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-18

2-4. 1-way Air Discharge Cassette Type


Specifications (50Hz)
Model name Cooling/Heating capacity(Note 1) Power supply Running current Electrical characteristics (Note 2) Power consumption Power factor Starting current Main unit Appearance Ceiling Panel Model Panel color Height Main unit Outer dimension Ceiling panel Width Depth Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid/Low) Motor Controller Air filter Gas side Connecting pipe Liquid side Drain port (mm) (mm) (Nominal dia. mm) (dB(A))
O / 9.5 O / 6.4

50Hz

MMU(kW)

AP0071YH 2.2/2.5

AP0091YH 2.8/3.2

AP0121YH 3.6/4.0

AP0152SH 4.5/5.0

AP0182SH 5.6/6.3

AP0242SH 7.1/8.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.24 0.053 95 0.6 0.34 0.042 _ 0.53 0.37 0.046 _ 0.54 0.62 0.075 _ 0.80

Heat-insulating material attached Zinc hot dipping steel plate RBC-UY135PG W : Silky shade (1Y8.5/0.5) (mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg) 235 850 400 18 1,050 470 22 3.5 Finned tube 21 5.5 RBC-US21PGE Moon white (Munsel 2.5GY9.0/0.5) 200 1,000 710 20 1,230 800 22

Non-flammable insulation

Polyethylene foam + Expanded polystyrene


Centrifugal fan

(m3/h) (W)

540/480/420 22

750/690/630

780/720/660 30

1,140/960/810

Remote controller Standard filter (Long life filter)


O / 12.7 O / 15.9 O / 9.5

25 (Polyvinyl chloride tube:External dia.32 Internal dia.25) 42/39/34 Available 37/35/32 38/36/34 45/41/37

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-19

2-4. 1-way Air Discharge Cassette Type


Specifications (60Hz)
Model name Cooling/Heating capacity(Note 1) Power supply Running current Electrical characteristics (Note 2) Power consumption Power factor Starting current Main unit Appearance Ceiling Panel Model Panel color Height Main unit Outer dimension Ceiling panel Width Depth Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Fan unit Standard air flow (High/Mid/Low) Motor Controller Air filter Gas side Connecting pipe Liquid side Drain port (mm) (mm) (Nominal dia. mm) (dB(A))
O / 9.5 O / 6.4

60Hz

MMU(kW)

AP0071YH 2.2/2.5

AP0091YH 2.8/3.2

AP0121YH 3.6/4.0

AP0152SH 4.5/5.0

AP0182SH 5.6/6.3

AP0242SH 7.1/8.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.26 0.056 98 0.60 0.35 0.041 _ 0.53 0.39 0.045 _ 0.54 0.62 0.073 _ 0.80

Heat-insulating material attached Zinc hot dipping steel plate RBC-UY135PG W : Silky shade (1Y8.5/0.5) (mm) (mm) (mm) (mm) (mm) (mm) (kg) (kg) 235 850 400 18 1,050 470 22 3.5 Finned tube 21 5.5 RBC-US21PGE Moon white (Munsel 2.5GY9.0/0.5) 200 1,000 710 20 1,230 800 22

Non-flammable insulation

Polyethylene foam + Expanded polystyrene


Centrifugal fan

(m3/h) (W)

540/480/420 22

750/690/630

780/720/660 30

1,140/960/810

Remote controller Standard filter (Long life filter)


O / 12.7 O / 15.9 O / 9.5

25 (Polyvinyl chloride tube:External dia.32 Internal dia.25) 42/39/34 37/35/32 Available 38/36/34 45/41/37

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-20

2-4. 1-way Air Discharge Cassette Type


Dimension
MMU-AP0071YH, AP0091YH, AP0121YH

Panel external dimension 1050 Ceiling open dimension 1010

Ceiling open dimension 430

20
Power supply connecting port Drain pipe connecting port (VP25) Center of panel Hanging bolt 4-M10 procured locally Refrigerant pipe connecting port (Gas side) 9.5 Discharge louver Refrigerant pipe connecting port (Liquid side) 6.4 Ceiling panel Procured locally Air discharge port Bottom face of ceiling Panel mounting hole 5 positions Air suction port

Dimensions
4

2.7

Model MMUAP0071YH,AP0091YH, AP0121YH

20
Support metal
A 235

Panel external dimension 470

B 245

C 200

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application 120 16 RBC-AMT31E and RBC-EXW21E2
120
100 or more 100 or more

200 or more

Space required for installation and servicing


Note: All dimensions are in mm.

2-21

B or more

MMU-AP0152SH, AP0182SH, AP0242SH


Cable inlet (Knockout hole)

252 112 Fresh air inlet (92 knockout hole) 112 (4-tapping screw under-hole)

248

Drain pipe connecting port (Be sure to connect the attached flexible hose.) 72
20

C/L

56

Cable inlet
43

233

100 760 Ceiling opening size 475 Hanging bolt pitch 710 Unit external size

C/L
220

800 Panel external size

122

20

1190 Ceiling opening size 1230 Panel external size

20

20

1060 Hanging bolt pitch

135

216

80 60

94 154

1000 Unit external size 706

Refrigerant pipe connecting port Gas side B Refrigerant pipe connecting port Liquid side A Hanging bolt M10 or W3/8 (Local supply)

200

93

Lower surface of ceiling

20

Ceiling panel (Sold separately)

For front air discharge unit (Sold separately) knockout hole

Model name MMUAP015, AP018 type


4
2.7

73.4

76

A
O / 6.4 O / 9.5

B
O / 12.7 O / 15.9

AP024 type

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit 120 TCB-AX21E2
120

16

Weekly timer application RBC-AMT31E and RBC-EXW21E2

2-22

2-5. Concealed Duct Standard Type


Appearance

Standard accessories
Part name
Installation Manual

Q'ty
1

Shape
_

Use
_

Part name
Washer

Q'ty
8

Shape

Use
For hanging down the unit

Insulated pipe

For heat insulating of pipe connecting section

Optional accessories
High Efficiency Filter 65 TCB-UFM11BFCE TCB-UFM21BFCE High Efficiency Filter 90 TCB-UFH51BFCE TCB-UFH61BFCE Standard filter and filter frame

High Efficiency Filter 65 TCB-UFM11BE TCB-UFM21BE TCB-UFM31BE TCB-UFM41BE High Efficiency Filter 90 TCB-UFH51BE TCB-UFH61BE TCB-UFH71BE TCB-UFH81BE

Filter Chamber TCB-FC281BE, TCB-FC501BE TCB-FC801BE, TCB-FC1401BE Filter kit for underside TCB-FK281BE, TCB-FK501BE TCB-FK801BE, TCB-FK1401BE Suction Canvas TCB-CA281BE, TCB-CA501BE TCB-CA801BE, TCB-CA1401BE Ceiling panel RBC-UD281PE, RBC-UD501PE RBC-UD801PE, RBC-UD1401PE

2-23

Parts Name

Model name TCB-UFM11BFCE TCB-UFM11BFCE(2 pcs.) TCB-UFM21BFCE TCB-UFM21BFCE(2 pcs.) TCB-UFH51BFCE TCB-UFH51BFCE(2 pcs.) TCB-UFH61BFCE TCB-UFH61BFCE(2 pcs.) TCB-FC281BE

Applied Model MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH MMD-AP0071/0091/0121BH MMD-AP0151/0181BH MMD-AP0241/0271/0301BH MMD-AP0361/0481BH

Notes

Remarks Use with TCB-FC281BE Use with TCB-FC501BE Use with TCB-FC801BE Use with TCB-FC1401BE Use with TCB-FC281BE Use with TCB-FC501BE Use with TCB-FC801BE Use with TCB-FC1401BE

High Efficiency Filter 65 (For rear suction)

Dust collecting effect : 65% (NBS Colorimentric method)

High Efficiency Filter 90 (For rear suction)

Dust collecting effect : 90% (NBS Colorimentric method)

Filter Chamber (For rear suction)

TCB-FC501BE TCB-FC801BE TCB-FC1401BE TCB-UFM11BE TCB-UFM21BE TCB-UFM31BE TCB-UFM41BE TCB-UFH51BE TCB-UFH61BE TCB-UFH71BE TCB-UFH81BE RBC-UD281PE(W) RBC-UD501PE(W) RBC-UD801PE(W) RBC-UD1401PE(W) TCB-CA281BE TCB-CA501BE TCB-CA801BE TCB-CA1401BE TCB-FK281BE TCB-FK501BE TCB-FK801BE TCB-FK1401BE

For high efficiency filter

High Efficiency Filter 65 (For underside suction)

Dust collecting effect : 65% (NBS Colorimentric method)

High Efficiency Filter 90 (For underside suction)

Dust collecting effect : 90% (NBS Colorimentric method)

Ceiling panel (Half panel for underside suction)

Suction Canvas (For underside suction)

Adjustment height of the suction canvas is more 40mm and 100mm

Filter kit for underside

Kit of underside prefilter & shielding plate of rear suction

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-24

2-5. Concealed Duct Standard Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Appearance Main unit Height Main unit Width Depth Height Suction ceiling panel Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Fan unit Motor (m3/h) 480 (420/340) (kg) 3.5 4 Finned tube Non-flammable insulation Centrifugal fan 570 650 780 (490/400) (540/480) (660/540) 120 40 100 Standard filter (Long life filter) Remote controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4 O / 12.7 O / 15.9 O / 9.5

50Hz

MMD- AP0071BH AP0091BH AP0121BH AP0151BH AP0181BH AP0241BH AP0271BH AP0301BH AP0361BH AP0481BH (kW) 2.2/2.5 2.8/3.2 3.6/4.0 4.5/5.0 5.6/6.3 7.1/8.0 8.0/9.0 9.0/10.0 11.2/12.5 14.0/16.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (A) 0.29 0.033 0.5 0.34 0.039 0.59 0.43 0.050 0.75 0.52 0.060 0.90 0.61 0.071 1.05 0.83 0.107 1.44 0.98 0.128 1.70

Electrical characteristics

Zinc hot dipping steel plate (mm) (mm) (mm) (mm) (mm) (mm) (kg) 28 32 630 780 500 43 6 55 7 550 700 800 9 1,080 1,430 320 1,000 1,350

Outer dimension

1,140 (990/870)

1,260 1,620 1,980 (1,080/870) (1,410/1,200) (1,710/1,490)

(W)

External static pressure (Pa) (factory setting) External static pressure Air filter Controller (W)

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 30/28/26 31/29/27

25 (Polyvinyl chloride tube) 32/30/28 Not available 33/31/29 34/32/29 36/34/32 38/36/32

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-25

2-5. Concealed Duct Standard Type


Specifications (60Hz)
Model name MMDAP0071BH 2.2/2.5 AP0091BH 2.8/3.2 AP0121BH 3.6/4.0 AP0151BH 4.5/5.0 AP0181BH 5.6/6.3 AP0241BH 7.1/8.0 AP0271BH 8.0/9.0 AP0301BH 9.0/10.0 AP0361BH 11.2/12.5 Cooling/Heating capacity (Note 1) (kW) Power supply Running current Electrical characteristics (A) 0.30 0.033 0.5

60Hz

14.0/16.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) 0.35 0.039 0.59 0.45 0.050 0.75 0.55 0.060 0.90 0.64 0.071 1.05 0.87 0.107 1.44 1.03 0.128 1.70

Power consumption (kW) Starting current (A)

Appearance Main unit Height Main unit Width Depth Outer dimension Suction ceiling panel Height Width Depth Main unit Total weight Ceiling panel Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Fan unit Motor External static pressure (factory setting) (m3/h) (W) 480 (420/340) (kg) 3.5 (mm) (mm) (mm) (mm) (mm) (mm) (kg) 28 630

Zinc hot dipping steel plate 320 700 800 9 780 500 32 4 Finned tube Non-flammable insulation Centrifugal fan 570 650 (490/400) (540/480) 780 (660/540) 120 1,140 (990/870) 1,260 (1,080/870) 1,980 1,620 (1,410/1,200) (1,710/1,490) 43 6 55 7 1,080 1,430 1,000 1,350

(Pa)

40

(pa) Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4 O / 12.7

100 Standard filter (Long life filter) Remote controller


O / 15.9 O / 9.5

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A))

25 (Polyvinyl chloride tube)

30/28/26

31/29/27

32/30/28 Not available

33/31/29

34/32/29

36/34/32

38/36/32

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-26

2-5. Concealed Duct Standard Type


Dimension
MMD-AP0071BH, AP0091BH, AP0121BH, AP0151BH, AP0181BH, AP0241BH, AP0271BH, AP0301BH, AP0361BH, AP0481BH
Drain pipe connecting port (Inner 32 vinyl chloride pipe VP25 connection) Hanging bolt 4-M10 (Procured locally) 41 Hanging bolt pitch A 7.5 B 50 25 Unit external dimension 40 800 Hanging bolt pitch 700 59 638 498 393
41

(When attaching directly)

150

125 knockout hole (For air intake)

142 Refrigerant pipe connecting port (Gas side F) 44 49 Air Discharge

91

131 50

50 243

215

196

Air Suction

70 to 270

10-4 tapping screw 160

Refrigerant pipe connecting port (Liquid side G)

26 power supply, remote controller wires drawing-out port

Panel C, L

Ceiling open dimension D

Ceiling opening 470

E Air Suction
Model MMDAP0071BH, AP0091BH, AP0121BH AP0151BH, AP0181BH AP0241BH, AP0271BH, AP0301BH AP0361BH, AP0481BH

240

A
616 766 1066 1416

B
550 700 1000 1350

C
350 500 800 1150

D
600 750 1050 1400

E
470 620 920 1270

F
9.5 12.7 15.9 15.9

G
6.4 9.4 9.5 9.5

(Note) Two of high efficiency filters available Deodorant filter not available

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2
271mm or less
100mm or less

(Note) Be sure to create a check port at position A as indicated in the following figure. This is for maintenance of the equipment.
Air outlet Ceiling opening part

(150mm) Check port A 450mm

Check port B 450mm Air filter 700mm for maintenance of air filter

550mm or less

300mm

Drain-up piping
700mm for maintenance of air filter

Note: All dimensions are in mm.

2-27

2-5. Concealed Duct Standard Type


Fan characteristics In case of square duct flange of discharge section
MMD-AP0071BH, AP0091BH
140

MMD-AP0121BH
140

Standard air volume: 480m/h

Standard air volume: 570m/h


Hi

Hi
120

gh

gh

sta

tic

sta

tic

pre

ss

ure

120

pre

ss

2(

it

10

0P a)

lim

at io n

(H

100

Ap pl ic

Hig

igh

hs

)
100

Ap

pl

ica

n tio

lim

it

ure

2(

10

0P a)

Hig

(H

hs

igh

External static pressure (Pa)

sur

External static pressure (Pa)

tati

tat

ic

cp

res

pre

ss

e1

ure

(70

1(

Pa )

70

80

Sta

(Hi

gh)

St
80

an

Pa )

da

(H

nd

rd

igh

Air volume limit (Max)

ard

sta

Air volume limit (Min)

pre

ssu

su

re

re

(40

(4

60

Pa )

Lo ws

(Hi

gh

60

Lo w

0P a)

sta

(H

tic

igh

tat

ic p

pre

res

ss

40

Sta

su

ure

re

(H

nd

(H

ard

igh

40

Sta

igh

nd

pre

ard

ssu

pre

re

ss

(20

ure

Pa )

(20

20

(Lo w)

Pa )

20

(Lo w)

Long life filter


0 200 400 480 600 0 300

Long life filter


500 570 700

Air volume (m/h)

Air volume (m/h)

MMD-AP0151BH
140

MMD-AP0181BH
Standard air volume: 650m/h
140

Standard air volume: 780m/h

Hig
120

Hig
h st atic pre ssu
120

h st

atic

pre

ssu

Ap
100

pl

ica

n tio

it lim

re 2

re 2

(10

0Pa

) (H

igh)
100

Ap

pl

ica

tio

i nl

t mi

(10

0Pa

Air volume limit (Max)


) (H igh)

Air volume limit (Min)

sta

tic

tic

pr

es

High

stat

External static pressure (Pa)

stati

External static pressure (Pa)

High

ic p

ress

c pre

ure

ssur

1 (7

e1(

0Pa

80

70P a) (H

) (H igh)

igh)

80

Air volume limit (Min)

Air volume limit (Max)

Sta

nda

rd s

rd s

tatic

tatic

pre

pres

60

ssu

sure

re (

40P a) (

60

(40P a) (

Hig

Hig

h)

h)

Low

Low

sta

tic

sta

pre

tic

40

pre

ssu

re

ssu

Sta

re (

nda

Hig

40

(Hi

gh)

h)

Sta

rd p

nda

res

rd

sur

pre

e (2

0Pa

ssu

re

20

) (L

(20

ow)

20

Pa )

(Lo w)

Long life filter


0 400 600 650 800 0 500

Long life filter


700 780 900

Air volume (m/h)

Air volume (m/h)

Note: "High" and "Low" is Air flow.

2-28

Air volume limit (Max)

Air volume limit (Min)

Sta

nda

MMD-AP0241BH, AP0271BH
Standard air volume: 1140m/h

MMD-AP0301BH
Standard air volume: 1260m/h

140

140

High
120

High
static press ure 2 (100P a) (Hig
120

static

press

ure 2

(100

Ap
100

plic

at

ion

i lim

h)

Ap
High sta
100

plic

atio

nl

t imi

Pa) ( H

igh)

External static pressure (Pa)

(70Pa)

External static pressure (Pa)

tic pres

sure 1

High s

tatic p

(High)

ressu

re 1 (7

0Pa) (H

igh)

80

80

Air volume limit (Min)

Air volume limit (Min)

Stand

Air volume limit (Max)

Stand

ard s

ard sta

tatic p

tic pre

ressu

ssure

60

re (40

Pa) (H

(40Pa

) (Hig

igh)

60

h)

Low s

tatic p

Low

ressu

static

re (H

press

igh)

ure (H

igh)

40

Stand

40

ard pre

ssure

(20Pa

) (Low

Stand
)
20

ard p

ressu

re (20

Pa) (L ow)

20

0 800

Long life filter


1000 1140 1200 1300

0 900

Long life filter


1100 1260 1300

Air volume (m/h)

Air volume (m/h)

MMD-AP0361BH
140

MMD-AP0481BH
Standard air volume: 1620m/h
140

Standard air volume: 1980m/h

High s
120

tatic

press

ure 2

(100

Hig

Ap
100

c pli

o ati

i lim

Pa) ( H

120

h st

igh)

atic

pre

Ap

c pli

o ati

i nl

t mi

ssu

re 2

(10

0Pa

) (H

igh)

High

External static pressure (Pa)

External static pressure (Pa)

static

100

press

High

ure 1

stati

(70Pa

c pre

) (Hig

ssur

h)

e1(

70P a) (H

igh)

80

80

Air volume limit (Min)

Air volume limit (Max)

Stan

Air volume limit (Min)

dard

static

rd s

press

tatic

ure (

pres

60

40Pa

sure

) (Hig

h)

60

(40P a) (

Hig

h)

Low
40

Low

static

stati

press

c pre

ure (H

ssur

e (H

igh)

40

igh)

Stan

Stan
dard pres sure (20P a) (L

dard

pres

sure

20

ow)

(20P a) (L

ow)

20

0 1200

Long life filter


1620 2000

Long life filter


0 1400 1800 1980 2200

Air volume (m/h)

Air volume (m/h)

Note: "High" and "Low" is Air flow.

2-29

Air volume limit (Max)

Sta

nda

Air volume limit (Max)

2-6. Slim Duct Type


Appearance

Standard accessories
Part name
Installation Manual insulating pipe Washer Hose band Flexible hose Heat insulator

Q'ty
1 2 8 1 1 1

Shape
This manual (Be sure to hand over to customer)

Usage

For insulating pipe connecting section M10 x O / 34 For hanging-down the unit For connecting drain pipe For adjusting of drain pipe connecting For insulating drain connecting section

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-30

2-6. Slim Duct Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Electrical characteristics Running current Power consumption Starting current Appearance Outer Height x Width x Depth dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid./Low) (m /h) Motor Fan unit External static pressure (Factory setting) External static pressure Air filter pressure loss Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4
3

50Hz

MMD(kW)

AP0071SPH 2.2/2.5

AP0091SPH 2.8/3.2

AP0121SPH 3.6/4.0

AP0151SPH 4.5/5.0

AP0181SPH 5.6/6.3

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (A) 0.29 0.039 0.51 0.29 0.039 0.51 0.31 0.043 0.54 Zinc hot dipping steel plate (mm) (kg) 22 22 210/845/645 22 Finned tube Polyethylene foam + Polyurethane foam Centrifugal fan 540/470/400 600/520/450 60 6 6-16-31-46 (4steps) 4 5 5-15-30-45 (4steps) 5 Standard filter supplied (Long life filter) Remote controller
O / 12.7

0.32 0.045 0.56

0.39 0.054 0.68

23

23

690/600/520

780/680/580

(W) (Pa) (Pa) (m3/h)

4 4-14-29-44 (4steps) 6

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) Under air inlet Back air inlet (dB(A)) (dB(A)) (dB(A))

25 (Polyvinyl chloride tube : External dia.32 Internal dia.25) 36/33/30 28/26/24 51 38/35/32 29/27/25 53 Available 39/36/33 32/30/28 54 40/38/36 33/31/29 55

Sound pressure level PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-31

2-6. Slim Duct Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Starting current Appearance Outer Height x Width x Depth dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid./Low) (m /h) Motor Fan unit External static pressure (Factory setting) External static pressure Air filter pressure loss Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4
3

60Hz

MMD(kW)

AP0071SPH 2.2/2.5

AP0091SPH 2.8/3.2

AP0121SPH 3.6/4.0

AP0151SPH 4.5/5.0

AP0181SPH 5.6/6.3

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (A) 0.27 0.037 0.47 0.27 0.037 0.47 0.30 0.041 0.53 Zinc hot dipping steel plate (mm) (kg) 22 22 210/845/645 22 Finned tube Polyethylene foam + Polyurethane foam Centrifugal fan 540/470/400 600/520/450 60 6 6-16-31-46 (4steps) 4 5 5-15-30-45 (4steps) 5 Standard filter (Long life filter) Remote controller
O / 12.7

0.31 0.043 0.54

0.052 0.65

23

23

690/600/520

780/680/580

(W) (Pa) (Pa) (m3/h)

4 4-14-29-44 (4steps) 6

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) Under air inlet Back air inlet (dB(A)) (dB(A)) (dB(A))

25 (Polyvinyl chloride tube : External dia.32 Internal dia.25) 36/33/30 28/26/24 51 Available 38/35/32 29/27/25 39/36/33 32/30/28 54 40/38/36 33/31/29 55

Sound pressure level PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-32

2-6. Slim Duct Type


Dimension
MMD-AP0071SPH, AP0091SPH, AP0121SPH, AP0151SPH, AP0181SPH
21
845

168 (inside)

57 20 21
21 803 (inside) Air filter 21 103

210

Refrigerant piping

4-O /4

19

511 645

67

31

168

120

67

805 80 59 910 33 163 Drain-up port Hanger plate

Fresh air inlet (Knock-out hole)

Air inlet connecting flange (Field supply)


Underside
41.5 8.2 or less

805

100

266.5

100

286.8

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

12.5 100 100 100 100 100 825 n=24 M5 (O / 4.2 mounting hole) 100 100 100

12.5
45.3

44.3

Rearside

805

12.5 100 100 100 100 100 100 100 100 825 n=22 M5 (O / 4.2 mounting hole)

12.5

2-33

44.3

188.6

170

100

40

359 372 422 502

O /9

80

*China only

MMD-AP007SPH-C, AP0091SPH-C, AP0121SPH-C, AP0151SPH-C, AP0181SPH-C, MMD-AP0071SH-C, AP0091SH-C, AP0121SH-C, AP0151SH-C, AP0181SH-C
21 845 57 21 803 (inside) 21 Natural drain port 67 210 168 (inside) 20 21

103

Refrigerant piping

19

4-O /4

511 645

31 168 359 372 422 502 67 805 910 33 163 Drain-up port (SPH model only) Hanger plate 805
100 100 286.8 41.5 8.2 or less

O /9

146

80

120

80 Fresh air inlet (Knock-out hole)

59

Air inlet connecting flange (Field supply)


Underside

266.5

12.5 100 100 100 100 100 825 n=24 M5 (O / 4.2 mounting hole) 805 100 100 100

12.5
45.3

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2
188.6

44.3

Rearside

170

12.5 100 100 100 100 100 100 100 100 825 n=22 M5 (O / 4.2 mounting hole)

12.5

2-34

44.3

100

Weekly timer application RBC-AMT31E and RBC-EXW21E2

40

2-6. Slim Duct Type


Fan characteristice

MMD-AP0071SPH MMD-AP0091SPH
Standard air volume : 540m3/h 60

MMD-AP0121SPH

Standard air volume : 600m3/h 60


High (50Pa)

50

Upper limit of external static pressure(50Pa)

High (50Pa)

50

Upper limit of external static pressure(50Pa)

External static pressure (Pa)

Upper limit of external static pressure(35Pa)

External static pressure (Pa)

40

High (35Pa)

High (35Pa)

40
Low (50Pa) Upper limit of external static pressure(35Pa) Low (35Pa) Lower limit of external static pressure (50Pa) High (20Pa)

30

Upper limit of external static pressure(20Pa)

Low (50Pa)

Lower limit of external static pressure (50Pa) High (20Pa)

30

20

Upper limit of external static pressure(10Pa)

Low (35Pa) Lower limit of external static pressure (35Pa) High (10Pa)

20

Upper limit of external static pressure(20Pa)

Lower limit of external static pressure (35Pa) High (10Pa)

10

Low (20Pa) Lower limit of external static pressure (20Pa) Low (10Pa)

10

Low (20Pa) Upper limit of external static pressure(10Pa)

Low (10Pa)

Lower limit of external static pressure (20Pa)

0 300

400

500

600

700

0 300

400

500

600

700

Air Volume (m3/h)

Air Volume (m3/h)

MMD-AP0151SPH

MMD-AP0181SPH

Standard air volume : 690m3/h 60


60

Standard air volume : 780m3/h

Upper limit of external static pressure(50Pa)

High (50Pa)

High (50Pa) Upper limit of external static pressure(50Pa)

50

50

External static pressure (Pa)

External static pressure (Pa)

40

Upper limit of external static pressure(35Pa)

High (35Pa)
High (35Pa)

40

Low (50Pa)

30

Low (50Pa)

Lower limit of external static pressure (50Pa)

30

Upper limit of external static pressure(35Pa) Low (35Pa) High (20Pa)

Lower limit of external static pressure (50Pa)

High (20Pa)

20

20

Low (35Pa)

Lower limit of external static pressure (35Pa) High (10Pa)

Upper limit of external static pressure(20Pa) Upper limit of external static pressure(10Pa)

10

Upper limit of external static pressure(20Pa)

Lower limit of external static pressure (35Pa) Low (20Pa) Lower limit of external static pressure (20Pa)

10
Low (20Pa) Lower limit of external static pressure (20Pa) Low (10Pa)

Upper limit of external static pressure(10Pa)

Low (10Pa)

High (10Pa)

0 400

0 400

500

600

700

800

900

500

600

700 m3

800

Air Volume (

/h)

Air Volume (m3/h)

2-35

2-6. Slim Duct Type


(Filter attached)

MMD-AP0071SPH MMD-AP0091SPH
Standard air volume : 540m3/h 60

MMD-AP0121SPH

Standard air volume : 600m3/h 60

High (50Pa)

50

Upper limit of external static pressure(50Pa)

High (50Pa)

50
Lower limit of externa static pressure (50Pa)
Upper limit of external static pressure(50Pa) Low (50Pa)

Lower limit of external static pressure (50Pa)

External static pressure (Pa)

External static pressure (Pa)

40

40

30

Upper limit of external static pressure(35Pa) Low (35Pa)

Low (50Pa)

Lower limit of external static pressure (35Pa)

30

Upper limit o external static pressure(35Pa) Low (35Pa) Upper limit o external static pressure(20Pa)

High (35Pa)

Lower limit of external static pressure (35Pa)

20
Upper limit of external static pressure(20Pa) High (20Pa) Lower limit of extern static pressure (20Pa) Low (20Pa)

20

High (20Pa) Lower limit of external static pressure (20Pa)

Low (20Pa)

10
Upper limit of external static pressure(10Pa)

10
High (10Pa) Standard filter pressure loss
Upper limit o external static pressure(10Pa)

High (10Pa)

0 300

Low (10Pa)

Low (10Pa)

Standard filter pressure loss

400

500

600

700

0 300

400

500

600

700

Air Volume (m3/h)

Air Volume (m3/h)

MMD-AP0151SPH
Standard air volume : 690m3/h 60
High (50Pa) Upper limit of external static pressure(50Pa)

MMD-AP0181SPH

60
Upper limit of external static pressure(50Pa)

Standard air volume : 780m3/h


High (50Pa)

50
Upper limit of external static pressure(35Pa) High (35Pa) Lower limit of external static pressure (50Pa)

50
Upper limit of external static pressure(35Pa) Lower limit of external static pressure (50Pa)

External static pressure (Pa)

External static pressure (Pa)

40

40

Low (50Pa)

30
Upper limit of external static pressure(20Pa)

Low (50Pa) High (20Pa)

Lower limit of external static pressure (35Pa)

30

High (35Pa)

Lower limit of external static pressure (35Pa)

Low (35Pa)

20

Low (35Pa) High (10Pa) Upper limit of external static pressure(10Pa) Lower limit of externa static pressure (20Pa)

20

Upper limit of external static pressure(20Pa) Upper limit of external static pressure(10Pa)

High (20Pa) Lower limit of external static pressure (20Pa) High (10Pa) Low (20Pa)

10

Low (20Pa)

10
Low (10Pa) Standard filter pressure loss

0 400

500

600

700

800

0 400

Low (10Pa)

Standard filter pressure loss

500

600

700

800

900

Air Volume (m3/h)

Air Volume (m3/h)

2-36

2-6. Slim Duct Type


CHINA model (Filter attached)

MMD-AP0071SPH-C, SH-C MMD-AP0091SPH-C, SH-C


Standard air volume : 540m3/h

MMD-AP0121SPH-C, SH-C

Standard air volume : 600m3/h

60

60
High (50Pa)

Upper limit of external static pressure(50Pa)

High (50Pa)

50
Upper limit of external static pressure(35Pa)

50

Upper limit of external static pressure(50Pa)

High (35Pa)

External static pressure (Pa)

High (35Pa)

External static pressure (Pa)

40

40
Low (50Pa)

30

Upper limit of external static pressure(35Pa)

Low (50Pa)

Lower limit of external static pressure (50Pa)

30

Upper limit of external static pressure(35Pa) Low (35Pa) Upper limit of external static pressure(20Pa) High (20Pa)

Lower limit of external static pressure (50Pa)

High (20Pa)

20

Upper limit of external static pressure(20Pa)

Low (35Pa) Lower limit of external static pressure (35Pa) High (10Pa)

20

Lower limit of external static pressure (35Pa)

Low (20Pa)

10
Low (20Pa) Upper limit of external static pressure(10Pa)

10
High (10Pa)

Low (10Pa)

Lower limit of external static pressure (20Pa)

Upper limit of external static pressure(10Pa)

Lower limit of external static pressure (20Pa) Low (10Pa)

0 300

400

500

600

700

0 300

400

500

600

700

Air Volume (m3/h)

Air Volume (m3/h)

MMD-AP0151SPH-C, SH-C

MMD-AP0181SPH-C, SH-C
Standard air volume : 780m3/h

Standard air volume : 690m3/h

60
Upper limit of external static pressure(50Pa) High (50Pa)

60
High (50Pa) Upper limit of external static pressure(50Pa)

50
Upper limit of external static pressure(35Pa) High (35Pa)

50
Upper limit of external static pressure(35Pa)

High (35Pa)

External static pressure (Pa)

External static pressure (Pa)

40

40

Low (50Pa)

30
High (20Pa)

Lower limit of external static pressure (50Pa)

Low (50Pa)

30
Low (35Pa)

Lower limit of external static pressure (50Pa)

20

Low (35Pa) High (10Pa)

Lower limit of extern static pressure (35Pa)

20

Upper limit of external static pressure(20Pa)

High (20Pa) Lower limit of extern static pressure (35Pa)

10

Upper limit of external static pressure(20Pa) Low (20Pa) Upper limit of external static pressure(10Pa)

10
Lower limit of external static pressure (20Pa)

High (10Pa) Low (20Pa) Upper limit of external static pressure(10Pa) Lower limit of exte static pressure (20Pa) Low (10Pa)

Low (10Pa)

0 400

500

600

700
m3

800

0 400

500

600

700

800

900

Air Volume (

/h)

Air Volume (m3/h)

2-37

2-7. Concealed Duct High Static Pressure Type


Appearance

Standard accessories
Part name
Installation Manual

Q'ty
1

Shape
_

Use
_

Part name
Insulation

Q'ty
1

Shape

Use
For insulating the liquid pipe connection

Insulation

For insulating the gas pipe connection

Optional accessories
Filter Chamber TCB-FCY21DE, TCB-FCY31DE TCB-FCY51DE Long Life Pre-Filter TCB-PF1D-1E TCB-PF2D-1E

High Efficiency Filter 65 TCB-UFM1D-1E, TCB-UFM2D-1E Drain pump kit TCB-DP31DE


Parts Name High Efficiency Filter 65

High Efficiency Filter 90 TCB-UFH5D-1E, TCB-UFH6D-1E


Model name TCB-UFM1D-1E TCB-UFM2D-1E(2 pcs.) TCB-UFM1D-1E(2 pcs.) TCB-UFH5D-1E Applied Model MMD-AP0181H MMD-AP0241/0271/0361H MMD-AP0481H MMD-AP0181H MMD-AP0241/0271/0361H MMD-AP0481H MMD-AP0181H MMD-AP0241/0271/0361H MMD-AP0481H MMD-AP0181H MMD-AP0241/0271/0361H MMD-AP0481H MMD-AP0181H to AP0481H Stand-up 330 or less (from bottom face of ceiling) For high efficiency filter or long life pre-filter Dust collecting effect : 50% (Weight method) Dust collecting effect : 90% (NBS Colorimentric method) Notes Dust collecting effect : 65% (NBS Colorimentric method) Remarks Use with TCB-FCY21D Use with TCB-FCY31D Use with TCB-FCY41D Use with TCB-FCY21D Use with TCB-FCY31D Use with TCB-FCY41D Use with TCB-FCY21D Use with TCB-FCY31D Use with TCB-FCY41D

High Efficiency Filter 90

TCB-UFH6D-1E (2 pcs.) TCB-UFH5D-1E (2 pcs.) TCB-PF1D-1E

Long life Pre-filter

TCB-PF2D-1E (2 pcs.) TCB-PF1D-1E (2 pcs.) TCB-FCY21DE

Filter Chamber

TCB-FCY31DE TCB-FCY51DE

Drain Pump Kit

TCB-DP31DE

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-38

2-7. Concealed Duct High Static Pressure Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer Height x Width x Depth dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow Motor Fan unit External static pressure (Factory setting) External static pressure Air flow limit Lower limit/Upper limit Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 12.7 O / 6.4

50Hz

MMD(kW)

AP0181H 5.6/6.3

AP0241H 7.1/8.0

AP0271H 8.0/9.0

AP0361H 11.2/12.5

AP0481H 14.0/16.0

1 phase 50Hz 220V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.81 0.184 99 1.3 1.35 0.299 96 3.5 Zinc hot dipping steel plate (mm) (kg) 50 380 x 850 x 660 52 Finned tube Non-flammable insulation Centrifugal fan (m3/h) (W) (Pa) (Pa) (m3/h) 720/1,080 900 160 137 68.6-137-196 1,060/1,580 Option or field supply Remote controller
O / 15.9 O / 9.5

1.63 0.368 98 4.1

1.84 0.414

4.8

380 x 1,200 x 660 56 67

1,320

1,600 260

2,100

1,280/1,920

1,680/2,520

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 37

25 (One side of male screw) 40 Not available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-39

2-7. Concealed Duct High Static Pressure Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer Height x Width x Depth dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow Motor Fan unit External static pressure (Factory setting) External static pressure Air flow limit Lower limit/Upper limit Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 12.7 O / 6.4

60Hz

MMD(kW)

AP0181H 5.6/6.3

AP0241H 7.1/8.0

AP0271H 8.0/9.0

AP0361H 11.2/12.5

AP0481H 14.0/16.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.92 0.198 98 1.30 1.80 0.385 97 3.40 Zinc hot dipping steel plate (mm) (kg) 50 380 x 850 x 660 52 Finned tube Non-flammable insulation Centrifugal fan (m3/h) (W) (Pa) (Pa) (m3/h) 720/1,080 900 160 137 68.6-137-196 1,060/1,580 Option or field supply Remote controller
O / 15.9 O / 9.5

2.07 0.450 99 3.90

2.26 0.490

4.35

380 x 1,200 x 660 56 67

1,320

1,600 260

2,100

1,280/1,920

1,680/2,520

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (dB(A)) 37

25 (One side of male screw) 40 Not available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-40

2-7. Concealed Duct High Static Pressure Type


Dimension
MMD-AP0181H, AP0241H, AP0271H, AP0361H, AP0481H
MMD-AP0181H to AP0361H
710 (Hanging bolt mounting pitch 800)

MMD-AP0481H

Hole for hanging bolt (4-O / 12 x 72)

Power supply/ communication piping port (O / 26) (Under electric parts box)

Hole for hanging bolt (4-O / 12 x 72) Power supply/ communication piping port (O / 26) (Under electric parts box)

Electric parts box Refrigerant pipe connecting port (Gas side O / B)

Refrigerant pipe connecting port (Liquid side O / A)

Electric parts box Refrigerant pipe connecting port (Liquid side O / 9.5) Refrigerant pipe connecting port (Gas side O / 15.9)

Screw hole for duct mounting (6-M6) Air suction port Drain pipe connecting port (VP25)

Screw hole for duct mounting (8-M6) Air suction port Drain pipe connectingport (VP25) Z view

Z view

Z view

Screw hole for duct mounting (4-M6)

Air discharge port

Air discharge port Screw hole for duct mounting (6-M6)

Screw hole for duct mounting (8-M6)

Air discharge port

AP0181H to AP0271H type

AP0361H type

Model MMDAP0181H AP0241H, AP0271H, AP0361H, AP0481H

A 6.4 9.5

B 12.7 15.9

Space required for installation and servicing *1


500 mm or more 600 mm or more

Service space

Check port 600

Service space

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2

Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2
120

2.7

120

16

Note: All dimensions are in mm.

2-41

2-7. Concealed Duct High Static Pressure Type


Fan Characteristics
MMD-AP0181H
Fan motor current (A)
1.5 Standard air volume: 900 m3/h

MMD-AP0241H, AP0271H
Fan motor current (A)
2.0 Standard air volume: 1,320 m3/h

High static pressure tap

High static pressure tap


Medium static pressure tap

Medium static pressure tap


1.0

1.5

0.5

Low static pressure tap

1.0

Low static pressure tap

300 250 50Hz 60Hz 50Hz 60Hz Air volume lower limit
st

Outside static pressure (Pa)

pre

Outside static pressure (Pa)

200

sta

tic

Air volume lower limit

ss

ed

ure

at

Air volume upper limit

iu

tap

200

ic

pr e

150

st

ed

ss

at

iu

ic

ur e

ta

pr

st

Lo w

es

su

150

at

ic

100

st

re

pr

at

ta

es

ic

su

re

pr

ta

es

su

100

re

ta

50

50

700

800

900

1,000

1,100

0 1,000

1,100

1,200

1,320 1,300 1,400 Air volume (m/h)

1,500

1,600

Air volume (m/h)

MMD-AP0361H
Standard air volume: 1,600 m3/h 2.5

MMD-AP0481H
3.0 Standard air volume: 2,100 m3/h

Fan motor current (A)

Fan motor current (A)

High static pressure tap


2.0

High static pressure tap


2.5

Medium static pressure tap


1.5

2.0

Medium static pressure tap

Low static pressure tap


1.0

1.5

Low static pressure tap


0.5

Hig

50Hz 60Hz

Air volume upper limit

250

250

Air volume lower limit

Outside static pressure (Pa)

Outside static pressure (Pa)

200 Air volume lower limit


Me diu

pre

ssu

re t

hs

ap

tat

ic

200

pre

ss

150

sta

ed

ure

tic

ium

tap

pre

ssu

re

150

sta

tic

tap

pr

es

su

100

Lo ws

Lo w
100

re

ta

tat

st

ic p

at

ic

res

pr

su

re

es

50

tap
50

su

re

ta

1,400

1,500

1,600

1,700

1,800

2,100 1,500 2,000 Air volume (m/h) 2,500

Air volume (m/h)

2-42

Air volume upper limit

h st

atic

Hig

50Hz 60Hz

Air volume upper limit

Hi

gh

250

Hi gh

w Lo st at ic pr es su re

ta p

2-8. Under ceiling Type


Appearance

Standard accessories
Part name
Installation Manual

Q'ty
1

Shape
This manual

Use
(Be sure to hand over to the customer)

Part name
Heat insulator

Q'ty
1

Shape

Use
For heat insulating of drain connecting section

Heat insulating pipe Installation pattern

For heat insulation of pipe connecting section

Washer

For hanging-down unit

For confirmation of ceiling opening and main unit position

Hose band

For connecting drain pipe

Banding band

For drain hose forming

Drain hose

For drain piping

Bushing

For power supply cord protection Heat insulator

For sealing of piping hole

Optional accessories

Elbow piping kit TCB-KP12CE2 TCB-KP22CE2

Drain pump kit TCB-DP22CE2

Parts Name

Model name

Applied Model MMC-AP0151/0181H

Notes Stand-up 600 or less (from bottom face of ceiling)

Remarks Use with TCB-KP12CE Use with TCB-KP22CE

Drain Pump Kit

TCB-DP22CE2 MMC-AP0241H/0271/0361H/0481H TCB-KP12CE2 MMC-AP0151/0181H

Elbow Piping Kit TCB-KP22CE2

Needed when Drain Pump Kid is MMC-AP0241H/0271/0361H/0481H used

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-43

2-8. Under Ceiling Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Motor Controller Air filter Gas side Connecting pipe Liquid side Drain port (mm) (mm) (Nominal dia. mm) (dB(A)) 35/32/30 36/33/30
O / 12.7 O / 6.4

50Hz

MMC(kW)

AP0151H 4.5/5.0

AP0181H 5.6/6.3

AP0241H 7.1/8.0

AP0271H 8.0/9.0

AP0361H 11.2/12.5

AP0481H 14.0/16.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (A) 0.29 0.033 0.43 0.32 0.038 0.48 0.42 0.050 0.62 White (Munsell 10Y 9.3/0.4) 0.78 0.091 1.17 0.84 0.110 1.25

Electrical characteristics

Height x Width x Depth

(mm)

210 x 910 x 680 22

210 x 1,180 x 680 26 Finned tube Non-flammable insulation Centrifugal fan

210 x 1,595 x 680 34

(kg)

Fan unit

(m3/h)

720/600/540 30

780/660/540

1,110/900/840 40 Remote controller Standard filter (Long life filter)

1,650/1,380/1,200 1,800/1,560/1,320 80

(W)

O / 15.9 O / 9.5

20 (Polyvinyl chloride tube) 38/36/33 Not available 41/38/35 43/40/37

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-44

2-8. Under Ceiling Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Electrical characteristics Running current (A) 0.30 0.033 0.43 MMC(kW) AP0151H 4.5/5.0 AP0181H 5.6/6.3 AP0241H 7.1/8.0 AP0271H 8.0/9.0 AP0361H 11.2/12.5

60Hz

AP0481H 14.0/16.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) 0.34 0.038 0.48 0.44 0.050 0.62 White (Munsell 10Y 9.3/0.4) 0.82 0.091 1.17 0.87 0.110 1.25

Power consumption (kW) Starting current Appearance Outer Height x Width x Depth (mm) dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Motor Controller Air filter Gas side Connecting Liquid side pipe (mm) (mm) (m3/h) (kg) (A)

210 x 910 x 680

210 x 1,180 x 680

210 x 1,595 x 680

22

26 Finned tube Non-flammable insulation Centrifugal fan

34

Fan unit

720/600/540

780/660/540

1,110/900/840

1,650/1,380/1,200 1,800/1,560/1,320

(W)

30

40 Remote controller Standard filter (Long life filter)

80

O / 12.7 O / 6.4

O / 15.9 O / 9.5

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

20 (Polyvinyl chloride tube)

(db(A))

35/32/30

36/33/30

38/36/33

41/38/35

43/40/37

Not available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-45

2-8. Under Ceiling Type


Dimension
MMC-AP0151H, AP0181H, AP0241H, AP0271H, AP0361H, AP0481H
Upper piping drawing-out port (Knockout hole) Power supply cable taking-in port (Knockout) Remote controller piping taking-in port (Knockout hole) Piping drawing-out port (Knockout port)

320 170

(Hanging position)

70

Left drain size

Drain port VP20 (Inner diam. O / 26, hose supplied)

B (Hanging position) Refrigerant pipe (Liquid side O / D) Refrigerant pipe (Gas side O / C)

Drain pipe connecting port

Model MMCAP0151H, AP0181H

A 910 1180 1595

B 855 1125 1540

C 12.7 15.9 15.9

D 6.4 9.5 9.5

AP0241H, AP0271H AP0361H, AP0481H

Wireless sensor mounting section (Optional)

Hanging bolt

Within 50

Ceiling surface Unit

250 or more

250 or more

(Front side to be positioned horizontally.)

Space required for installation and servicing


Remote controller cable taking-in port Power supply taking-in port (Knockout hole) Remote controller cable taking-in port (Knockout hole)
2.7

4 Wired remote controller RBC-AMT31E

Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX22CE2 Weekly timer application 120 16 RBC-AMT31E and RBC-EXW21E2
120

Air taking-in port (Duct sold separately) (Knockout hole O / 92) Drain left piping drawing-out port Piping hole on the wall (Knockout hole) (O / 100 hole)

Note: All dimensions are in mm.

2-46

500 or more

2-9. High Wall (1series) Type


Appearance

Standard accessories
High Wall type (1 series)
Part name
Installation Manual Heat Insulating pipe Wood screw O / 5.1 x 45 Installation plate

Q'ty
1

Shape
This manual

Use
(Be sure to hand over to customer) For heat insulating of pipe connecting section Used to fix installation plate

Part name
Installation pattern Screw cap

Q'ty
1

Shape
_

Use
Used for drilling holes and positioning installation plate Cover on fixing screw at side plate Used to fix attached pipe heat insulating material

12

Bundling band

Used to install indoor unit wall unit

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-47

2-9. High Wall 1series Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Suction grille and side panel Appearance Discharge grille Bottom surface Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Motor outlet Air filter Controller Gas side Connecting pipe Liquid side Drain port (mm) (mm) (Nominal dia. mm) (dB(A))
O / 9.5 O / 6.4

50Hz

MMK(kW)

AP0071H 2.2/2.5

AP0091H 2.8/3.2

AP0121H 3.6/4.0

AP0151H 4.5/5.0

AP0181H 5.6/6.3

AP0241H 7.1/8.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (A) 0.30 0.035 0.36 Silky mist (Munsell 1Y 8.9/0.5) City gray (Munsell N6.5) Silky mist (Munsell 1Y 8.9/0.5) (mm) 0.32 0.037 0.42 0.35 0.040 0.47

Electrical characteristics

Height x Width x Depth

368 x 895 x 210 18 Finned tube

368 x 1,055 x 210 19

368 x 1,430 x 210 25

(kg)

Non-flammable insulation Cross-flow fan

Fan unit

(m3/h) (W)

600/540/480 30

780/660/600

1,200/1,020/900

Standard filter (Simple filter) Remote controller


O / 12.7 O / 15.9 O / 9.5

20 (Polyvinyl chloride tube)

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

39/34/31 Available

42/38/35

42/38/35

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-48

2-9. High Wall 1series Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Starting current (A) (kW) (A) MMK(kW) AP0071H 2.2/2.5 AP0091H 2.8/3.2 AP0121H 3.6/4.0 AP0151H 4.5/5.0 AP0181H 5.6/6.3

60Hz

AP0241H 7.1/8.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) 0.32 0.035 0.46 Silky mist (Munsell 1Y 8.9/0.5) City gray (Munsell N6.5) Silky mist (Munsell 1Y 8.9/0.5) 0.34 0.037 0.48 0.35 0.040 0.60

Suction grille and side panel Appearance Discharge grille Bottom surface Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Fan Standard air flow (High/Mid/Low) unit Motor outlet Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5

Height x Width x Depth

(mm)

368 x 895 x 210

368 x 1,055 x 210

368 x 1,430 x 210

(kg)

18 Finned tube Non-flammable insulation Cross-flow fan

19

25

(m3/h) (W)

600/540/480 30

780/660/600

1,200/1,020/900

Standard filter (Simple filter) Remote controller


O / 12.7 O / 6.4 O / 15.9 O / 9.5

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

20 (Polyvinyl chloride tube)

(dB(A))

39/34/31 Available

42/38/35

42/38/35

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-49

2-9. High Wall 1series Type


Dimension
MMK-AP0071H, AP0091H, AP0121H
Position of holes on the installation plate.

Long hole for wooden screw 15-6 X 30 690 (Installation plate) Hole for anchor bolt 10-10 X 20 long hole (Including installation plate) 210 Including installation plate (Accessory) Earth screw (M4) (Inside of electric parts box) Refrigerant pipe connecting port O Gas side 9.5 / 9.5 Refrigerant pipe connecting port Liquid side O / 6.4

Upper end of installation plate

Air suction port Discharge port (Air direction upward/downward/leftward/rightward are adjustable.) Piping port from left/right sides (Knockout hole) Gas pipe 440 Liquid pipe 540 Drain pipe 560 At shipment (When drawing pipe from left)

Drain pipe connecting port

300 or more

300 or more

Space required for service

Wired remote controller RBC-AMT31E


4 Simple wired remote controller RBC-AS21E2
2.7

Weekly timer application RBC-AMT31E and RBC-EXW21E2


120
16

120

Wireless remote controller kit TCB-AX21E2

30 or more

Note: All dimensions are in mm.

2-50

MMK-AP0151H, AP0181H

182.5

690 (Installation plate)

Hole for wooden screw 15-6 X 30 182.5 Hole for anchor bolt 10-10 X 20 long hole

Upper end of installation plate

(Including installation plate) 210 Including installation plate (Accessory) Earth screw (M4) (Inside of electric parts box) Refrigerant pipe Refrigerant pipe connecting port connecting port Liquid side O / 6.4 Gas side O / 12.7

Air suction port Air discharge port (Air direction upward/downward/leftward/rightward air adjustable.) Piping port from left/right sides (Knockout hole) Gas pipe 440 Liquid pipe 540 Drain pipe 560 At shipment (When drawing pipe from left)

Drain pipe connecting port

Wired remote controller RBC-AMT31E

300 or more

300 or more

Space required for service

Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2 Note: All dimensions are in mm.

2-51

30 or more

MMK-AP0241H

Position of holes on the installation plate

Hole for wooden screw 21-6 X 30 170 1090 (Installation plate) 170

Hole for anchor bolt 16-10 X 20 long hole

Upper end of installation plate

(Including installation plate) 210 Including installation plate (Accessory) Earth screw (M4) (Inside of electric parts box) Refrigerant pipe connecting port Gas side O / 15.9 Refrigerant pipe connecting port Liquid side O / 9.5

Air discharge port (Air direction upward/ Air suction port downward/leftward/rightward air adjustable.) Piping port from left/right sides (Knockout hole) Gas pipe 440 Liquid pipe 540 Drain pipe 560 At shipment (When drawing pipe from left)

Drain pipe connecting port

300 or more

300 or more

Space required for service

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2 Note: All dimensions are in mm.

2-52

30 or more

2-10. High Wall (2series) Type


Appearance

Standard accessories
High Wall type (2 series)
Part No. Part name (Q'ty) Part No. Part name (Q'ty) Part No. Part name (Q'ty)

1 Installation plate x 1

3 Battery x 2

5 Mounting screw O / 4 x 25 x 6

2 Wireless remote controller x 1

4 Remote controller holder x 1

6 Pan head wood screw O / 3.1 x 16 x 2

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-53

2-10. High Wall 2 series Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Suction grille and side panel Appearance Discharge grille Bottom surface Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Motor outlet Air filter Controller Gas side Connecting pipe Liquid side Drain port Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (mm) (mm) (Outer dia. mm) (dB(A)) (m3/h) (W) (A) (kW) (A) MMK(kW) AP0072H 2.2/2.5 AP0092H 2.8/3.2 AP0122H 3.6/4.0

50Hz

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) 0.17 0.017 0.22 0.18 0.018 0.23 Moon white Moon white Moon white 0.19 0.019 0.24

Electrical characteristics

Height x Width x Depth

(mm) (kg)

275 x 790 x 208 11 Finned tube Non-flammable insulation Cross-flow fan

Fan unit

480/420/360

510/450/360 30 Standard filter (Simple filter)

540/450/360

Wireless remote controller (WH-H2UE, Packed with indoor unit)


O / 9.5 O / 6.4

16 (Polyvinyl chloride tube)

35/32/29

36/33/29 Available

37/33/29

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note 3 : Wireless remote controller is packed with indoor unit. Wired remote controller (RBC-AMT31E, RBC-AS21E2) can be also connected. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-54

2-10. High Wall 2 series Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Power consumption Starting current Suction grille and side panel (A) (kW) (A) MMK(kW) AP0072H 2.2/2.5 AP0092H 2.8/3.2 AP0122H 3.6/4.0

60Hz

1 phase 60Hz 220V (Separate power supply for indoor units is required.) 0.18 0.017 0.22 0.19 0.018 0.23 Moon white Moon white Moon white 0.20 0.019 0.24

Electrical characteristics

Appearance Discharge grille


Bottom surface Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan

Height x Width x Depth

(mm) (kg)

275 x 790 x 208 11 Finned tube Non-flammable insulation Cross-flow fan

Fan unit Motor outlet Air filter Controller Gas side Connecting pipe Liquid side Drain port Sound pressure level(Note 2) (High/Mid/Low) PMV Kit (mm) (mm) (Outer dia. mm) (dB(A)) (W)

480/420/360

510/450/360 30 Standard filter (Simple filter)

540/450/360

Wireless remote controller (WH-H2UE, Packed with indoor unit)


O / 9.5 O / 6.4

16 (Polyvinyl chloride tube)

35/32/29

36/33/29 Available

37/33/29

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note 3 : Wireless remote controller is packed with indoor unit. Wired remote controller (RBC-AMT31E, RBC-AS21E2) can be also connected. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-55

2-10. High Wall 2 series Type


Dimension
MMK-AP0072H, AP0092H, AP0122H
Air inlet part
208 790 208

275

48
60

275

48
60

Knockout

Air outlet gril


790

Knockout

208

48

54.5

60

60

54.5

790

790

Hock for insulation plate Refrigerant pipe connecting port Gas side O / 9.5

321

Drain pipe Refrigerant pipe connecting port Liquid side O / 6.4

100mm or more

275

208

170mm or more

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

Space required for service

Note: All dimensions are in mm.

2-56

48

170mm or more *300mm or more *(For attached Flow Selector unit of heat recovery model)

275

2-11. Floor Standing Cabinet Type


Appearance

Standard accessories
Part name
Installation Manual Heat Insulating

Q'ty
1

Shape
_

Use

Part name
Bushing

Q'ty
1

Shape

Use
For installation in the wire knockout

For insulating the indoor unit pipe connections

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-57

2-11. Floor Standing Cabinet Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan (A) (kW) (%) (A) MML(kW) AP0071H 2.2/2.5 AP0091H 2.8/3.2 AP0121H 3.6/4.0 AP0151H 4.5/5.0 AP0181H 5.6/6.3

50Hz

AP0241H 7.1/8.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) 0.26 0.056 94 0.60 0.43 0.092 93 0.80 Silky shade (1Y8.5/0.5) 0.47 0.102 94 1.10

Height x Width x Depth

(mm) (kg) 37

630 x 950 x 230 40 Finned tube Non-flammable insulation Centrifugal fan 40

Fan unit

Standard air flow (High/Mid/Low)

(m3/h)

480/420/360

900/780/650

1,080/930/780

Motor outlet Air filter Controller Gas side Connecting pipe Liquid side Drain port

(W)

45 Standard filter (Simple filter) Remote controller

70

(mm) (mm) (Nominal dia. mm) (dB(A)) 39/37/35

O / 9.5 O / 6.4

O / 12.7

O / 15.9 O / 9.5

20 (Polyvinyl chloride tube) 45/41/38 Available 49/44/39

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-58

2-11. Floor Standing Cabinet Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Motor outlet Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4

60Hz

MML(kW)

AP0071H 2.2/2.5

AP0091H 2.8/3.2

AP0121H 3.6/4.0

AP0151H 4.5/5.0

AP0181H 5.6/6.3

AP0241H 7.1/8.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.25 0.053 96 0.60 0.44 0.092 95 0.80 Silky shade (1Y8.5/0.5) 0.53 0.113 97 1.10

Height x Width x Depth

(mm)

630 x 950 x 230 37 Finned tube Non-flammable insulation Centrifugal fan 40

(kg)

Fan unit

(m3/h)

480/420/360

900/780/650

1,080/930/780

(W)

45 Standard filter (Simple filter) Remote controller


O / 12.7

70

O / 15.9 O / 9.5

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

20 (Polyvinyl chloride tube)

(dB(A))

39/37/35

45/41/38

49/44/39

Available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-59

2-11. Floor Standing Cabinet Type


Dimension
MML-AP0071H, AP0091H, AP0121H, AP0151H, AP0181H, AP0241H
Fixing hole (Floor) (2-O / 10) Lower refrigerant piping port (50 X 100 knockout hole)

130

Wired remote controller (Sold separately) Operation switch section Fixing hole (Wall) (Two off knockout holes O / 10-O / 20)

Air discharge port

Hole fixing wall (2-10 X 24 long hole)

Air suction port Refrigerant pipe port (50 X 100 knockout hole on both sides) 100 ( left side ) Earth screw (M6) Refrigerant pipe port (O / 130 knockout hole)

Power supply cord hole (O / 26 knockout on both sides)

Dimensions
Model MMLAP0071H, AP0091H, AP0121H AP0151H, AP0181H AP0241H A
O / 9.5 O / 12.7 O / 15.9

Wired remote controller RBC-AMT31E


B
O / 6.4 O / 6.4 O / 9.5

Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

Refrigerant pipe connecting port (Liquid side O / B) Refrigerant pipe connecting port (Gas side O / A) Drain pipe connecting port (O / 20)

Space required for service Figure shows piping at the left side
Wall

Positional drawing of piping

1000 or more

(Front side) or more

500

300 or more

Wall (Front side)

Note: All dimensions are in mm.

2-60

2-12. Floor Standing Concealed Type


Appearance

Standard accessories
Part name
Installation Manual Heat insulation

Q'ty
1

Shape
_

Use
_

Part name
Drain receiver fixing screw Drain hose Heat insulated pipe

Q'ty
1

Shape

Use
For fix the drain receiver For water draining (Attaches to the drain receiver.) For insulating the drain receiver (Attaches to the drain receiver.)

For heat insulating the indoor unit pipe connections For water draining Drain filter (inside the drain receiver)

Drain pan

Drain filter

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-61

2-12. Floor Standing Concealed Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Fan unit Motor Static pressure range Air filter Controller Gas side Connecting pipe Liquid side Drain port (mm) (mm) (Nominal dia. mm) (dB(A))
O / 9.5 O / 6.4

50Hz

MML(kW)

AP0071BH 2.2/2.5

AP0091BH 2.8/3.2

AP0121BH 3.6/4.0

AP0151BH 4.5/5.0

AP0181BH 5.6/6.3

AP0241BH 7.1/8.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.25 0.056 97 0.60 Zinc hot dipping steel plate 0.45 0.090 87 0.80 0.46 0.095 90 1.00

Height x Width x Depth

(mm)

600 x 745 x 220 21 Finned tube Non-flammable insulation Centrifugal fan

600 x 1,045 x 220 29

(kg)

(m3/h)

460/400/300

740/600/490

950/790/640

(W) (kPa)

19 0 Standard filter attached (Simple filter) Remote controller


O / 12.7

70

O / 15.9 O / 9.5

20 (Polyvinyl chloride tube) 36/34/32 Not available 42/37/33

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-62

2-12. Floor Standing Concealed Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Fan unit Motor Static pressure range Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 9.5 O / 6.4

60Hz

MML(kW)

AP0071BH 2.2/2.5

AP0091BH 2.8/3.2

AP0121BH 3.6/4.0

AP0151BH 4.5/5.0

AP0181BH 5.6/6.3

AP0241BH 7.1/8.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) (A) (kW) (%) (A) 0.27 0.058 98 0.60 Zinc hot dipping steel plate 0.46 0.096 95 0.80 0.51 0.110 98 1.00

Height x Width x Depth

(mm)

600 x 745 x 220 21 Finned tube Non-flammable insulation Centrifugal fan

600 x 1,045 x 220 29

(kg)

(m3/h)

460/400/300 19 0

740/600/490 70

950/790/640

(W) (kPa)

Standard filter (Simple filter) Remote controller


O / 12.7 O / 15.9 O / 9.5

Drain port (Nominal dia. mm) Sound pressure level(Note 2)(High/Mid/Low) (dB(A)) PMV Kit

20 (One side of male screw) 36/34/32 Not available 42/37/33

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-63

2-12. Floor Standing Concealed Type


Dimension
MML-AP0071BH, AP0091BH, AP0121BH, AP0151BH, AP0181BH, AP0241BH

Fixing hole (Floor)

(Discharge port size in flange) Ceiling board section

150 or more (Service space) (Air discharge port size in flange)

150 or more (Service space)

2-O / 4.7 hole (Left/right side each)

Expansion valve box G-O / 4.7 hole (Front side and rear side each)

4-O / 15 hole (For mounting rear side)

2-12 5 18 hole Fixing hole (Floor)

No.
1 2 3 4 5

Name Pipe connecting port at liquid side (O / E) Pipe connecting port at gas side (O / F) Drain pipe connecting port (20A) Electric parts box (Earth terminal on the inside) Air filter

Dimensions
Model MMLA B C D 4 6.4 910 880 850 7 9.5 E F 9.5 12.7 15.9 G 5 8 AP0071BH, AP0091BH, AP0121BH 610 580 550 AP0151BH, AP0181BH AP0241BH

Wired remote controller 4 RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2
120
16
2.7

120

Note: All dimensions are in mm.

2-64

2-13. Floor Standing Type


Appearance

Standard accessories
Part name
Installation Manual

Q'ty
1

Shape
This manual

Use
(Be sure to hand over to the customer)

Part name
Heat insulator

Q'ty
1

Shape

Use
For heat insulating of drain connecting section

Heat insulating pipe Installation pattern

For heat insulation of pipe connecting section

Washer

For hanging-down unit

For confirmation of ceiling opening and main unit position

Hose band

For connecting drain pipe

Banding band

For drain hose forming

Drain hose

For drain piping

Bushing

For power supply cord protection Heat insulator

For sealing of piping hole

Optional accessories

Remote controller
Model Name Wired remote controller Simple wired remote controller Wireless remote controller kit Weekly timer application Central remote controller ON-OFF controller RBC-AMT31E RBC-AS21E2 TCB-AX21E2 RBC-AMT31E and RBC-EXW21E2 TCB-SC642TLE2 TCB-CC163TLE2

2-65

2-13. Floor Standing Type


Specifications (50Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics Power consumption Power factor Starting current Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Height x Width x Depth (mm) (kg) 48 (A) (kW) (%) (A) MMF(kW) AP0151H 4.5/5.0 AP0181H 5.6/6.3 AP0241H 7.1/8.0 AP0271H 8.0/9.0 AP0361H 11.2/12.5

50Hz

AP0481H 14.0/16.0

1 phase 50Hz 230V (220-240V) (Separate power supply for indoor units is required.) 0.67 0.150 97 0.90 1.10 W : Silky shade (1Y 8.5/0.5) 0.88 0.190 94 1.70 1.29 0.280 1.60 0.350 95 2.10

1,750 x 600 x 210 49 Finned tube Non-flammable insulation Centrifugal fan

1,750 x 600 x 390 65

Fan unit

Standard air flow (High/Mid/Low)

(m3/h)

900/780/660

1,200/1,020/840

1,920/1,680/1,380 2,160/1,860/1,560

Motor Air filter Controller Gas side Connecting pipe Liquid side Drain port

(W)

37

63 Standard filter (Simple filter) Remote controller

110

160

(mm) (mm) (Nominal dia. mm) (dB(A))

O / 12.7 O / 6.4

O / 15.9 O / 9.5

20 (Polyvinyl chloride tube) 46/43/38 49/45/40 Not available 51/48/44 54/50/46

Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound level are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB

2-66

2-13. Floor Standing Type


Specifications (60Hz)
Model name Cooling/Heating capacity (Note 1) Power supply Running current Electrical characteristics (A) MMF(kW) AP0151H 4.5/5.0 AP0181H 5.6/6.3 AP0241H 7.1/8.0 AP0271H 8.0/9.0 AP0361H 11.2/12.5

60Hz

AP0481H 14.0/16.0

1 phase 60Hz 220V (Separate power supply for indoor units is required.) 0.67 0.146 99 0.90 1.10 W : Silky Shade (1Y 8.5/0.5) 0.90 0.195 98 1.80 1.37 0.295 1.75 0.380 99 2.30

Power consumption (kW) Power factor Starting current (%) (A)

Appearance Outer dimension Total weight Heat exchanger Soundproof/Heat-insulating material Fan Standard air flow (High/Mid/Low) Motor Air filter Controller Gas side Connecting pipe Liquid side (mm) (mm)
O / 12.7 O / 6.4

Height x Width x Depth

(mm)

1,750 x 600 x 210

1,750 x 600 x 390

(kg)

48

49 Finned tube Non-flammable insulation Centrifugal fan

65

Fan unit

(m3/h)

900/780/660

1,200/1,020/840

1,920/1,680/1,380 2,160/1,860/1,560

(W)

37

63 Standard filter (Simple filter) Remote controller


O / 15.9 O / 9.5

110

160

Drain port (Nominal dia. mm) Sound pressure level(Note 2) (High/Mid/Low) PMV Kit

20 (Polyvinyl chloride tube)

(dB(A))

46/43/38

49/45/40

51/48/44

54/50/46

Not available

Note 1 : The cooling capacities and electrical characteristics are measured under the conditions specified by JIS B 8615 based on the reference piping. The reference piping consists of 5 m of main piping and 2.5 m of branch piping connected with 0 meter height. Note 2 : The sound levels are measured in an anechoic chamber in accordance with JIS B8616. Normally, the values measured in the actual operating environment become larger than the indicated values due to the effects of external sound. Note : Rated conditions Cooling : Indoor air temperature 27 C DB/19 C WB, Outdoor air temperature 35 C DB Heating : Indoor air temperature 20 C DB, Outdoor air temperature 7 C DB/6 C WB
O O O O O O

2-67

2-13. Floor Standing Typs


Dimension
MMF-AP0151H, AP0181H, AP0241H, AP0271H
Wall

Dimensions

Incase of installing distance is 50mm from wall

Model MMF-AP0151H, AP0181H

A
O / 12.7 O / 15.7

B
O / 6.4 O / 9.5

Lower refrigerant piping port (50 x 120 Knockout hole) Installation plate Discharge port 600 30 x 3 30 x 3 80 Wall

MMF-AP0241H, AP0271H

Wall

a
Control part Control cover

Wall

Space required for service (In case of right side piping )


Wall

More than 1000

Front

More Front than 500

More than 200

Wall

Floor Refrigerant piping port (Both side) (O / 80 Knockout)

Installation plate

Drain hose

Earth screw (M4)

Suction port Refrigerant piping hole (Back side) (O / 130 Knockout )

Refrigerant piping hole (Bottom side) (50 x 120 Knockout) Refrigerant piping joint (Gas side A)

Refrigerant piping position

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2
Details of hole for back side piping
In case a 1770 In case b 1773

Refrigerant piping joint (Liquid side B)

Details of hole for lower side piping

2- lower hole For M8 Screw bolt or M8 Anchor bolt

4- lower hole M8 Screw bolt ( For or M8 Anchor bolt ) 50 x 120 (Square opening) (For under surface piping)

(For backside piping)

O / 130 Knockout

Note: All dimensions are in mm.

2-68

MMF-AP0361H, AP0481H
Wall of installing distance is ( Incase ) 50mm from wall

Lower refrigerant piping port (50 x 120 Knockout) Installation plate Discharge port 600 30 x 3 30 x 3 80 Wall

Wall

a
Control part Control cover

Wall

Space required for service (In case of right side piping )


Wall

More than 1000

Front

More Front than 500

More than 200

Wall

Floor Refrigerant piping port (Both side) (O / 80 Knockout) Drain hose

Installation plate

Earth screw (M4) Dtain hose Refrigerant piping hole (Bottom side) (50 x 120 Knockout)

Suction port Refrigerant piping hole (Back side) (O / 130 Knockout) Refrigerant piping joint (Gas side O / 19)

Refrigerant piping position


Liquid side

Gas side

Wired remote controller RBC-AMT31E Simple wired remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21E2 Weekly timer application RBC-AMT31E and RBC-EXW21E2

Refrigerant piping joint (Liquid side O / 9.5)

Details of hole for back side piping


In case a 1770

Details of hole for lower side piping

2- lower hole M8 Screw bolt ( For or M8 Anchor bolt )

In case b 1773

4- lower hole M8 Screw bolt ( For or M8 Anchor bolt ) 50 x 120 (Square opening) (For under surface piping)

O / 130 Knockout (For backside piping)

Note: All dimensions are in mm.

2-69

2-14. Application controls of indoor units


[1] Remote location ON/OFF control box
Model Name Appearance Features Start and stop of the air conditioner is possible by a external signal and indication of operation/alarm externally.

TCB-IFCB-4E2

Application

Function Monitoring ON/OFF status (for indoor unit) Alarm status (system & indoor unit stop) ON/OFF command Air conditioner can be turned ON/OFF by external signals. The external ON/OFF signals will initiate the signals shown below.

Operation

Interface Display Remote Controller

ON /OFF COM

Non-voltage ON /OFF continious signal

Dimension
Outside view
200 Fix this control box to the place besides the indoor unit.

Inside view

1 2
6- 5.5 mounting hole Approx. 300 78 22

22

78

66 63.6 5
146.9 170

Approx. 1500

156

22

78

78

22

Note : All dimensions are in mm


(NOTE) Do not install the accessory parts at the following locations.
1. Location where combustible gas may leak 2. Location where direct sunlight shines 3. Location with high humidity such as bathroom, kitchen, etc. 4. Location with high levels of dust 5. Location where rain or dew drops such as outdoors 6. Location in 1m-range of a TV or radio No. 1 2 3 4 5 6 Case unit Case cover Harness to connect indoor unit P.C. board Harness for indication cable Harness for power supply Harness for ON/OFF command Name Specification Galvanized steel 0.8t Galvanized steel 0.8t CN61 connector UL1015 AWG18 tip-insulation type butt connector 3-core, 0.75mm2 UL1015 AWG18 tip-insulation type butt connector

2-70

Panels and accessories


Indoor unit type Accessory parts name Required accessory Ceiling panel Super Long Life Filter High Efficiency Filter 65 High Efficiency Filter 90 4-way Air Discharge Cassette Type Fresh air and Filter Chamber Optional Fresh air inlet Box Auxiliary fresh air Flange Spacer for height adjustment Air discharge direction kit Required accessory Ceiling panel Compact 4-way Air Discharge Cassette (600 x 600) Type Spacer for height adjustment Optional Fresh Air Chamber Fresh Air Intel Box Air Discharge Direction Kit 2-way Air Discharge Required accessory Ceiling panel Cassette Type Required accessory Ceiling panel 1-way Air Discharge Cassette Type Optional Front air discharge unit Auxiliary fresh air flange Model RBC-U21PG(W)-E2 TCB-LF1601UE2 TCB-UFM1601UE TCB-UFH1601UE TCB-GFC1601UE2 TCB-GB1601UE2 TCB-FF101URE2 TCB-SP1601UE TCB-BC1601UE RBC-UM11PG(W)E *** *** *** *** RBC-UW136PG RBC-UW266PG RBC-UW466PG RBC-US21PGE TCB-BU21HWE TCB-FF101URE2 TCB-UFM11BFCE TCB-UFM21BFCE High Efficiency Filter 65 TCB-UFM11BE TCB-UFM21BE TCB-UFM31BE TCB-UFM41BE TCB-UFH51BFCE TCB-UFH61BFCE High Efficiency Filter 90 TCB-UFH51BE TCB-UFH61BE TCB-UFH71BE TCB-UFH81BE RBC-UD281PE(W) Concealed Duct Type Optional Ceiling panel RBC-UD501PE(W) RBC-UD801PE(W) RBC-UD1401PE(W) TCB-CA281BE Suction Canvas TCB-CA501BE TCB-CA801BE TCB-CA1401BE TCB-FC281BE TCB-FC501BE Filter Chamber TCB-FC801BE TCB-FC1401BE TCB-FK281BE TCB-FK501BE Filter kit for underside TCB-FK801BE TCB-FK1401BE TCB-UFM1D-1E High Efficiency Filter 65 High Efficiency Filter 90 Concealed Duct High Static Pressure Type Optional Long Life Pre-Filter TCB-UFM2D-1E TCB-UFH5D-1E TCB-UFH6D-1E TCB-PF1D-1E TCB-PF2D-1E TCB-FCY21DE Filter Chamber Drain pump kit Drain pump kit Under Ceiling Type Optional Elbow piping kit TCB-FCY31DE TCB-FCY51DE TCB-DP31DE TCB-DP22CE2 TCB-KP12CE2 TCB-KP22CE2 AP0071-0121/AP0241-0301 AP0071-0121 AP0151-0181 AP0241-0301 AP0361-0481 AP0071-0121/AP0241-0301 AP0071-0121 AP0151-0181 AP0241-0301 AP0361-0481 AP0071-0121 AP0151-0181 AP0241-0301 AP0361-0481 AP0071-0121 AP0151-0181 AP0241-0301 AP0361-0481 AP0071-0121 AP0151-0181 AP0241-0301 AP0361-0481 AP0071-0121 AP0151-0181 AP0241-0301 AP0361-0481 AP0181/0481 AP0241-0361 AP0181/0481 AP0241-0361 AP0181/0481 AP0241-0361 AP0181 AP0241-0361 AP0481 AP0181-0481 AP0151-0481 AP0151-0181 AP0241-0481 *Required accessories when using Drain Pump Kit AP0481 use two pcs. Use two pcs. AP0481 use two pcs. Use two pcs. AP0481 use two pcs. Use two pcs. For rear suction For underside suction (Half panel for underside suction) For underside suction AP0241-AP0301 use two pcs. AP0151-0181/AP0361-0481 AP0361-AP0481 use two pcs. For underside suction AP0241-AP0301 use two pcs. AP0151-0181/AP0361-0481 AP0361-AP0481 use two pcs. AP0071-0121 AP0151-0301 AP0481 China market only Three-piece set Be used with TCB-GFC1601UE2 Be used with TCB-GFC1601UE2 Application model Remarks

2-71

3. PMV Kit

3-1. Selection of PMV Kit..........................................................3-2

3-2. Wiring Connections..............................................................3-2

3-3. Dimensions............................................................................3-3

3-1

3. PMV Kit
PMV-Kit (RBM-PMV0361E/RBM-PMV0901E) shall be required for quiter place application as an optional to reduce refrigerant sound especially in oil retrieval control or in transient operation as start up.

3-1. Selection of PMV Kit


Model name RBM-PMV0361E RBM-PMV0901E Indoor unit capacity type 007,009,012 type 015,018 type 024 type Diameter of refrigerant pipe O / 6.4 O / 6.4 O / 9.5

Liquid pipe

Gas pipe

Available

PMV Kit Indoor unit

Not Available
PMV Kit

Indoor

PMV Kit

Indoor unit

NOTE , Don t connect two or more indoor units to one PMV kit. Arrange one indoor unit and one PMV kit set to 1 by 1.

Refrigerant pipe
Real length between PMV Kit and indoor unit: 2m or more and up to 10m

3-2. Wiring connections


Be sure to use the attached connection cable (10m).
Indoor unit Pulse motor valve

PMV Kit

Connection cable PMV CN82 connector

Connector conversion cable

Indoor control PC board

3-2

3-3. Dimension PMV Kit


RBM-PMV0361E, RBM-PMV0901E

Refrigerant pipe connecting port (Liquid pipe)

Refrigerant pipe connecting port (Liquid pipe)

58 30

55

226

55

Connection cable (accessory) 30 26


36

76

161

50 or more

RBM-PMV0361E,PMV0901E
50 or more 50 or more

Box cover Check port 450 x 450


500 or more

55

76

55

200 or more

Binding band L Binding band M

Installation image
Binding band M Binding band M Binding band L Binding band M

RBM-PMV0901E (When attached joint are used)200 or more


50 or more

Heat insulating pipe Refrigerant pipe (Liquid side)

Refrigerant pipe (Gas side)

50 or more

73

73

Heat insulating pipe Refrigerant pipe (Liquid side)

200 or more

200 or more

Note: All dimensions are in mm.

3-3

4. Outdoor Units

4-1. Outdoor units........................................................................4-2

4-2. Branching joints and Headers..........................................4-5

4-3. Application controls of outdoor unit.............................4-7

4-1

4-1. Outdoor units


Specifications (50Hz)
Equivalent HP Model name Outdoor unit type Cooling capacity (*1) Standard heating capacity (*1) Power supply (*2) Running current Power consumption Cooling Electrical characteristics (*1) Heating Power factor EER (Energy Efficiency Ratio) Starting current Running current Power consumption Power factor EER (Energy Efficiency Ratio) Starting current External dimension Total weight Color Compressor Type Motor output Fan Fan unit Heat exchanger Refrigerant R410A (Charged refrigerant amount) (*3) High-pressure switch Protective devices Connecting port dia Connecting method gas side Liquid side Discharge gas side Liquid side Max. equivalent length Refrigerant piping Max. real length specifications (*4) Max. total pipe length (Real length) Max. Height between indoor units
Real length between PMV Kit and indoor unit

50Hz

Equivalent to 4HP MMY(kW) (kW) (A) (kW) (%) (kW/kW) (A) (A) (kW) (%) (kW/kW) (A) (mm) (kg) 12.5 2.71 94 4.61 MCY-MAP0401HT 12.1 12.5 13.2 2.82 93 4.29

Equivalent to 5HP MCY-MAP0501HT Inverter unit 14.0 16.0

Equivalent to 6HP MCY-MAP0601HT 15.5 18.0 21.4 4.63 94 3.35

1 phase 50Hz 230V (220-240V) 16.1 3.47 94 4.03 Soft start 18.3 4.00 95 4.00 Soft start Height 1,340/Width 900/Depth 320 117 Shilky shade (Munsell 1Y8.5/0.5) Hermetic Type (kW) (kW) (m3 /h) (kg) (MPa) (mm) (mm) (mm) (m) (m) (m) (m) (m) Flare Flare 15
125 (If the total bend length exceeds 125m, use the max equivalent length as the standard.)

22.2 4.85 95 3.71

2.3

3.1 Propeller fan (Quantity 2) 0.063 + 0.063

4.2

Motor output Air volume

5,820

6,120 Finned tube 7.2 Open : 3.73 Close : 2.9 *5 15.9 9.5

6,420

19.1 Brazing

Outdoor unit is higher than indoor unit : 30 Outdoor unit is lower than indoor unit : 20
2-10

Control wiring Total wire length(indoor unit- indoor unit/ indoor unit-outdoor unit control wiring, central control wiring) Max. No. of connected indoor units Sound pressure level (Cooling/Heating) *3
(dB(A))

Shield wire 1.25mm2 2cores, up to 1000m Shield wire 2.0mm2 2cores, up to 2000m 6 49/50 46/48 8 50/52 46/48 9 51/53 47/49

Night operation (Sound reduction)control*4 (dB(A))

Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB The standard piping means that main pipe length is 5 m, branching pipe length 2.5 m of branch piping connected with a 0 meter height. *2 : The source voltage must not fluctuate more than 10%. *3 : The amount does not consider extra piping lengths. Refrigerant must be added on site in accordance with the actual piping length. *4 : The maximum total piping length indicates the sum of one-way piping lengths on the liquid side or gas side. *5 : Discharge temp. sensor, Suction temp. sensor, Compressor case thermostat, High-pressure switch, Over-current sensor, High-pressure sensor, Low pressure sensor, Over-current relay. *1 : Rated conditions

4-2

4-1. Outdoor units


Specifications (60Hz)
Equivalent HP Model name Outdoor unit type Cooling capacity (*1) Standard heating capacity (*1) Power supply (*2) Running current Power consumption Cooling Electrical characteristics (*1) Heating Power factor EER (Energy Efficiency Ratio) Starting current Running current Power consumption Power factor EER (Energy Efficiency Ratio) Starting current External dimension Total weight Color Compressor Type Motor output Fan Fan unit Heat exchanger Refrigerant R410A (Charged refrigerant amount) (*3) High-pressure switch Protective devices Connecting port dia Connecting method gas side Liquid side Discharge gas side Liquid side Max. equivalent length Refrigerant piping Max. real length specifications (*4) Max. total pipe length (Real length) Max. Height between indoor units
Real length between PMV Kit and indoor unit

60Hz

Equivalent to 4HP MMY(kW) (kW) (A) (kW) (%) (kW/kW) (A) (A) (kW) (%) (kW/kW) (A) (mm) (kg) 13.1 2.71 94 4.61 MCY-MAP0401HT2D 12.1 12.5 13.8 2.82 93 4.29

Equivalent to 5HP MCY-MAP0501HT2D Inverter unit 14.0 16.0 1 phase 60Hz 220V 16.8 3.47 94 4.03 Soft start 19.1 4.00 95 4.00 Soft start

Equivalent to 6HP MCY-MAP0601HT2D 15.5 18.0 22.4 4.63 94 3.35

23.2 4.85 95 3.71

Height 1,340/Width 900/Depth 320 117 Shilky shade (Munsell 1Y8.5/0.5) Hermetic Type

(kW) (kW) (m3 /h) (kg) (MPa) (mm) (mm)

2.3

3.1 Propeller fan (Quantity 2) 0.063 + 0.063

4.2

Motor output Air volume

5,820

6,120 Finned tube 7.2 Open : 3.73 Close : 2.9 *5 15.9 9.5 Flare Flare

6,420

19.1 Brazing 15

(m) (m) (m) (m) (m)

125 (If the total bend length exceeds 125m, use the max equivalent length as the standard.)

Outdoor unit is higher than indoor unit : 30 Outdoor unit is lower than indoor unit : 20
2-10

Control wiring Total wire length(indoor unit- indoor unit/ indoor unit-outdoor unit control wiring, central control wiring) Max. No. of connected indoor units Sound pressure level (Cooling/Heating) *3
(dB(A))

Shield wire 1.25mm2 2cores, up to 1000m Shield wire 2.0mm2 2cores, up to 2000m 6 49/50 46/48 8 50/52 46/48 9 51/53 47/49

Night operation (Sound reduction)control*4 (dB(A))

Cooling : Indoor air temperature 27oC DB/19oC WB, Outdoor air temperature 35oC DB Heating : Indoor air temperature 20oC DB, Outdoor air temperature 7oC DB/6oC WB The standard piping means that main pipe length is 5 m, branching pipe length 2.5 m of branch piping connected with a 0 meter height. *2 : The source voltage must not fluctuate more than 10%. *3 : The amount does not consider extra piping lengths. Refrigerant must be added on site in accordance with the actual piping length. *4 : The maximum total piping length indicates the sum of one-way piping lengths on the liquid side or gas side. *5 : Discharge temp. sensor, Suction temp. sensor, Compressor case thermostat, High-pressure switch, Over-current sensor, High-pressure sensor, Low pressure sensor, Over-current relay. *1 : Rated conditions

4-3

4-1. Outdoor unit


Dimension
MCY-MAP0401HT, MCY-MAP0501HT, MCY-MAP0601HT, MCY-MAP0401HT2D, MCY-MAP0501HT2D, MCY-MAP0601HT2D
Knockout(Drain)
17.5

29
21

90

Drain hole(O / 20x88) 191 20 Drain hole(O / 25) Air B lege


in let

70

A legs
i in

365

40

40

17.5

21

26 150

60

Air outlet

600 900

108 320

Refrigerant pipe connecting port (O / 9.5 flare at liquid side) Refrigerant pipe connecting port (O / 15.9 flare at gas side)
1340 722 718 625

40 54

43

Mounting bolt hole / 12 x 17U-shape cut-out) Details of A legs Details of B legs (O

40

17.5

Air let

43

40

Mounting bolt hole (O / 12 x 17slot)


12

Knockout(Drain)

350

67 154

60 314 307 95

27
60

Knockout for lower piping 86 7


7

27

58 161 400

Z View

Diameter of refrigerant pipe


Name Control wiring and piping hole Power supply wiring hole Notes

Model name
MCY-MAP0401HT* MCY-MAP0501HT*

58

Gas side
O / 15.9 (Flare) O / 15.9 (Flare) O / 19.1
Blazing connection with attached joint socket.

Liquid side
O / 9.5 (Flare) O / 9.5 (Flare) O / 9.5 (Flare)

Knockout hole O / 38

MCY-MAP0601HT*

Space required for service


150 or more

2-O / 12 x 17U -shape cut-out (F or M 10 Anchor bolt)

Air inlet 300 or more Mnimum distance up to wall

365

150 or more

46
80

Air outlet 500 or more

2-O / 12 x 17 slot (F or M 10 Anchor bolt)

600

165

32

60

45

Note: All dimensions are in mm.

4-4

89 25

4-2. Branching joints and headers


Branch header
RBM-HY1043E, HY1083E

Gas side

A B 80 x n 50

O /E

O /D

Insulator

Liquid side

A B 80 x n B

O /E

O /D

O /D

Insulator

74.5

Model Gas side RBM-HY1043E

A 380

B 90

n 3

Accessory socket x Qty 6 x 4, 9 x 4, 14 x 1,

83.6 22.2 15.9 _

18 x 1, 70 x 1 60 15.9 9.5 3 1 x 4, 6 x 8, 18 x 1 60 _ 15.9 9.5 7 1 x 8, 6 x 1, 9 x 8, 70 x 1 6 x 1, 9 x 1 9 x 1 14 x 1,

Liquid side 360

Gas side RBM-HY1083E

700

90

83.6 22.2 15.9

Liquid side 680

Note: All dimensions are in mm.

4-5

61

Y-shape branch joint


RBM-BY53E, BY103E

O /C

O /D

Gas side

Insulator A

Liquid side
O /C O /D

Insulator A

Model Gas side RBM-BY53E

A 250

B 80

Accessory socket x Qty 5 x 2, 54 x 2, 9 x 1, 51 x 1

15.9 12.7

Liquid side 200

70

12.7

9.5

1 x 2, 7 x 1, 52 x 2,

O /D

5 x 1 10 x 1, 70 x 1, 5 x 2, 13 x 2, 89 x 1 6 x 1, 9 x 1, 18 x 1,

Gas side RBM-BY103E

350

80

22.2 19.1

Liquid side 250

80

15.9 12.7

2 x 1, 54 x 1

Note: All dimensions are in mm.

4-6

O /D

O /B

4-3. Application controls of outdoor unit


Note : The P.C. boards of outdoor unit (TCB-PCDM2E, TCB-PCMO2E, TCB-PCIN2E) can be installed up to two boards.
Model Name Appearance Function

Power peak-cut control


Feature The upper limit capacity and current of the outdoor unit is restricted based on the demand request signal from outside.

Normal current Outdoor unit capacity type Normal current (Maxim running current) MCY0401 type
25A

0501 type
28A

0601 type
31A

Size : 71 x 85
Wiring
Length Up to 500m Up to 200m Up to 400m Size 2-core or 3-core, 0.75mm2 2-core, 0.75mm2 * 2-core, 1.5mm2 * Type Shield wire Shield wire

Application

Input wiring Output wiring

* In conformity with design 60245 IEC 57 Function / Electric wiring diagram Two type control can be selected by setting SW07 on the interface P.C. board of the outdoor unit.

TCB-PCDM2E

[ Standard funciton ]
Outdoor unit
I/F P.C Boad TCB-PCDM2E Display Relay

Local Supply

SW07 Bit2 OFF

OPERATION

Power Supply L1 L1

:Display lamp suring power peak-cut control.


In case of pulse signal Be sure to prepare the point of contact for each terminal. The time of the pulse signal is more than 100msec. Don't switch on both SW1 and SW2 terminal simultaneously.

Connection Cable

COM ON PJ17 ON COM OFF OFF

SW1

SW2

SW1

*Install this optional P.C. board in the inverter assembly of the outdoor unit.

CN513

SW2

Shield wire

SW07-Bit2 OFF
Input
SW1 OFF ON SW2 ON OFF

SW07-Bit1 OFF

SW07-Bit1 ON

Display Relay
(L1) OFF ON

Capacity Current Capacity Current 100% (Nomal) 100% (Nomal) 100% (Normal) 100% (Normal) 0% (stop) 0% (stop) Up to 60% Up to 80%

! CAUTION) Be sure to prepare a non-voltege point for each terminal. Display Relay capacity of "OPERATION" Below AC240V 0.5A (COSl=100%) When connecting load such as relay coil to "L1" load, insert the noise surge absorber. Below DC24V 1A (Non-indutive load) When connecting load such as relay coil to "L1" load, insert the bypass circuit.

4-7

Model Name

Appearance

Function

[ Expansion function ]
Outdoor unit
I/F P.C Boad TCB-PCDM2E Display Relay

Local Supply

SW07 Bit2 ON

OPERATIO L1

Power Supply L1

:Display lamp suring power peak-cut control.

Connection Cable

COM ON PJ17 ON COM OFF OFF

SW1

CN513

SW2

Shield wire

TCB-PCDM2E

SW07-Bit2 ON
Input
SW1 OFF ON OFF ON SW2 OFF OFF ON ON

SW07-Bit1 OFF

SW07-Bit1 ON

Display Relay
(L1) OFF ON ON ON

Capacity Current Capacity Current 100% (Normal) 100% (Normal) 100% (Normal) 100% (Normal) Up to 80% Up to 80% Up to 85% Up to 90% Up to 60% Up to 70% Up to 75% Up to 80% 0% (stop) 0% (stop) Up to 60% Up to 70%

! CAUTION) Be sure to prepare non voltage continuous point of contact for each terminal. Display Relay capacity of "OPERATION" Below AC240V 0.5A (COSl=100%) When connecting load such as relay coil to "L1" load, insert the noise surge absorber. Below DC24V 1A (Non-indutive load) When connecting load such as relay coil to "L1" load, insert the bypass circuit.

4-8

Model Name

Appearance

Function

[2] Snowfall fan control


Feature Outdoor fan is operated by the snowfall signal from outside. Function
TCB-PCMO2E COM SMC Cooling Local Supply

Size : 55.5 x 60

TCB-PCMO2E

Application

SMC : Cooling mode select input (switch)


Terminal Input signal Operation Snowfall fan control (Operates outdoor fan.) SMC

ON OFF ON
Usual operation

OFF
This control is activated when a input signal increases or decreases. (The increasing or decreasing signal needs to be held for a minimum of 100m/sec in order to activate the control)

[3] External master ON/OFF control


Feature The outdoor unit starts or stops the system. Function
TCB-PCMO2E COM SMC Cooling Heating SMH Local Supply

SMC : Input signal for start SMH : Input signal for stop
Terminal Input signal
*Install this optional P.C. board in the inverter assembly of the outdoor unit.

Operation Starts all indoor units.

ON
SMC

OFF ON
SMH Stops all indoor units.

OFF
Ensure terminal contacts are securely fixed. This control is activated when the input signal increases or decreases (The increasing or decreasing signal needs to be held for a minimum of 100m/sec in order to activate the control.)

4-9

Model Name

Appearance

Function

[4] Night operation (Sound reduction) control


Feature Sound level can be reduced by restricting the compressor and fan speeds. Function
TCB-PCMO2E COM Local Supply

Size : 55.5 x 60

SMC Cooling

TCB-PCMO2E

Application

SMC : Cooling mode designated input switch


Terminal Input signal Operation Night operation control SMC

ON OFF ON
Usual Operation

OFF
This control is activated when the input signal increases or decreases. (The increasing or decreasing signal needs to be held for a minimum of 100m/sec in order to activate the control).

[5] Operation mode selection control


Feature This control can restrict the selectable operation mode. Function
*Install this optional P.C. board in the inverter assembly of the outdoor unit.
TCB-PCMO1E COM SMC Cooling Heating SMH Local Supply

SMC : Cooling mode designated input switch SMH : Heating mode designated input switch
SMC ON OFF SMH OFF ON Selected operation mode Only cooling mode permitted Only heating mode permitted

Ensure terminal contacts are securely fixed.

4-10

Model Name

Appearance

Function

[6] Error / Operation output control


I/F P.C. Board

*
Connection Cable

TCB-PCIN2E
Display Relay
OPERATION

Local Supply Power Supply


L1

TCB-PCIN2E

Size : 73.0 x 79 Application

CN511

PJ20
Display Relay
EMG

Power Supply
L2

L1 : Operation monitoring lamp L2 : Error monitoring lamp Ensure terminal contacts are securely fixed. Display Relay capacity of "OPERATION" and "EMG" Below AC240V 0.5A(COSf=100%) When connecting a load such as a relay coil to "L1,L2", insert the noise surge absorber. Below DC24V 1A(Non-inductive load) When connecting a load such as a relay coil to "L1,L2", insert the byass circuit.

*Install this optional P.C. board in to the inverter assembly of outdoor unit.

4-11

Dimension TCB-PCDM2E
Terminal Screw M3 x 6 71 61 4-4O / hole

85
Terminal Screw M4 x 8

TCB-PCMO2E

75

55.5 45.5 4-4O / hole

Terminal Screw M3 x 6

60

TCB-PCIN2E
79 69

50

4-

4 hole

73

Terminal (Screw M3 )

63

4-12

5. Controls

-Outline of application control..............................................5-2

5-1. Control devices....................................................................5-3

5-2. Controller dimensions......................................................5-11

5-1

Outline of application Control

5. Controls

LONWORKS
Touch screen controller Monitoring Remote control Schedule operation Error code indication Alarm list indication Monthly report Energy monitoring data etc. BMS-LSV4E Intelligent server TCS-Net Interface BMS-IFLSV1E

LON Gateway

Mini-SMMS

Power peak-cut control board TCB-PCDM2E External master ON/OFF board TCB-PCDMO2E Energy Monitoring relay Interface BMS-IFWH3E

Super Digital Inverter Digital Inverter

Super Modular Multi Outdoor Unit

1:1model connection interface TCB-PCNT30TLE2

I/F

Error output control board TCB-PCIN2E

Local supply Power Meter

Alarm Status output ON/OFF Command


Remote location ON/OFF control board TCB IPCB-4E

Power peak-cut control signal

Master ON/OFF signal

Error/operation output

5-2

Batch drive, error output Master ON/OFF signal

Central remote controller TCB-SC642TLE2

Side remote controller

Master remote controller

Weekly timer RBC-EXW21E2 Air-conditioning Management System on site


1 BACnetTM : ANSl/ASHRAE1351995, A Data CommuniCation Protocol for Bulding Automation and ControI Networks. 2 LoNWoRKS, Resisterd trademark of Echelon Corporation

Weekly timer RBC-EXW21E2

Wired remote controller RBC-AMT31E Simple remote controller Wireless remote RBC-AS21E2 controller

5-1. Control devices


5-1-1. Applications for indoor remote controller
Basic function System diagram Model Wired remote controller RBC-AMT31E Simple remote controller RBC-AS21E2
Indoor unit Possible up to Max. total length 500m Remote controller

Main remote controller

Wireless remote controller kit TCB-AX21U(W)-E2 RBC-AX22CE2 TCB-AX21E2

Individual control
1-1 Air conditioner is individually operated at a distance.
Wireless remote controller

Indoor unit

Wireless Remote controller

Max.8 indoor units

(((

Receiver unit

Wired remote controller RBC-AMT31E Simple remote controller RBC-AS21E2

GROUP control
1-2 One remote controller can control a group of up to a maximum. 8 indoor units.Operating on the same setting
Indoor unit Indoor unit Indoor unit Indoor unit

Remote controller

Possible up to Max.total length 500m

5-3

Basic function

System diagram

Model Wired remote controller RBC-AMT31E Simple remote controller RBC-AS21E2 Wireless remote controller kit TCB-AX21U(W)-E2 RBC-AX22CE2 TCB-AX21E2

Wired system

Indoor unit

Remote controller Master

Remote controller Side

Possible up to Max. total length 500m

Two remote control


1-3 Air conditioner is controlled by two remote controllers in two locations.

Wireless system

Indoor unit

Wireless remote controller 1 Master

Wired & Wireless combination control (Either one of the two controllers can be set as side control).

(((

Wireless remote controller 2 Side

Indoor unit

Remote controller

Weekly timer function


Setting of ON-OFF 3 times par day Timer operation time is displayed. Holiday period

(( (

((
Wireless remote controller

(
Wired remote controller RBC-AMT31E

+
Weekly timer RBC-EXW21E2

1-4

Control by weekly timer


Weekly schedule operation

Indoor unit

Remote controller

Weekly timer

5-4

5-1-2. Application controls for central remote controller


Basic function System diagram Model Central remote controller TCB-SC642TLE2
U3, U4 Mini-SMMS Outdoor unit Line-3 Indoor unit U1, U2

Indoor remote controller Wired remote controller RBC-AMT31E Simple remote controller RBC-AS21E2

Zone 4

Indoor remote controller U3, U4 U5, U6


Zone 3

Outdoor unit Line-2

Super MMS Indoor unit

U1, U2

Zone 2

Indoor remote controller U3, U4 Outdoor unit Line-1 Mini-SMMS Indoor unit

2-1

Central management controller for 64 units

Zone 1

U1, U2

PMV Kit Indoor remote controller Power Central supply remote controller Single phase 220/230/240V

Function of central remote controller Individual control for up to 64 indoor units. Individual control for max. 64 indoor units divided in to 4 zones. (Up to 16 indoor units for each zone.) Up to 16 outdoor header units are connectable. 4 specific central control settings to restrict individual operation by remote controller are selectable. Different settings for one of 1 to 4 zones. Usable with other central control devices (Up to 10 central control devices in one control circuit) Two selectable control modes Central controller mode/Remote controller mode Setting of simultaneous ON/OFF 3 times per day when a controller is combined with using a weekly timer.

U3, U4

Outdoor unit Indoor unit U1, U2

2-2

Central remote controller + Weekly timer Weekly operation schedule can be set by connecting a weekly timer to the central remote controller

Central remote controller TCB-SC642TLE2

+
Weekly timer RBC-EXW21E2

PMV Kit Indoor remote controller Single phase 220/230/240V Power supply Weekly timer

Indoor remote controller Wired remote controller RBC-AMT31E or Simple remote controller RBC-AS21E2

Central remote controller

5-5

Basic function

System diagram

Model Central remote controller TCB-SC642TLE2 Indoor remote controller Wired remote controller RBC-AMT31E

U3, U4

Outdoor unit U1, U2

Power supply Single phase 220/230/240V

Indoor unit PMV Kit Central remote controller

Even when grouping operation is performed by connecting multiple indoor units to 1 line, the indoor remote controller is required.

2-3

Central remote controller without indoor remote controller

Example of grouping operation U3, U4

Outdoor unit U1, U2

Power supply

(Group) Indoor remote controller is required Central remote controller

PMV Kit

Available

Single phase 220/230/240V

U3, U4 Outdoor unit U1, U2

Power supply

(Group)

PMV Kit

Available
Central remote controller

Single phase 220/230/240V

5-6

Basic function

System diagram

Model Central remote controller TCB-SC642TLE2 TCB-SC163TLE2 "1 : 1 model" connection interface TCB-PCNT30TLE2 RAV-SM560KRT-E, SM800KRT-E are not compatible to connect Indoor remote controller Wired remote controller RBC-AMT31E

Power supply U3, U4 Outdoor unit U1, U2

Central remote controller

Simple remote controller RBC-AS21E2

2-4

Central management control with "1 : 1 model"

*1
Indoor unit

PMV Kit

Indoor remote controller "1:1 model" connection interface

* TOSHIBA Digital Inverter System and Super Digital Inverter System

5-7

5-1-3. Application control for network


Basic function System diagram Model LN interface TCB-IFLN640TLE "1 : 1 model" connection interface TCB-PCNT30TLE2 RAV-SM560KRT-E, SM800KRT-E are not compatible to connect Indoor remote controller Wired remote controller RBC-AMT31E

or
Simple remote controller RBC-AS21E2

LON Center LON WORKS LN Interface TCB-

3-1

LONWORKS R (*1)
Outdoor unit

*1

PMV Kit Remote controller "1:1 model" connection interface

*1 TOSHIBA Digital Inverter System and Super Digital Inverter System

The LONWORKS interface should be connected between a building management computer and a Mini-SMMS / Super HRM / Super MMS system. Max. 64 indoor units are connectable per interface.

*1) LONWORKS : Registerd trademark Echelon corporation.

5-8

Basic function

System diagram

Model BACnet server BMS-LSV4E BACnet server software XXX-XXXXXX TCS-Net Relay Interface BMS-IFLSV1E "1 model" connection interface TCB-PCNT30TLE2

BAC net center

RAV-SM560KRT-E, SM800KRT-E are not compatible to connect. Indoor remote controller Wired remote controller RBC-AMT31E

BAC net server

TCB-

TCN-NET relay interface


Outdoor unit

*1

Simple remote controller RBC-AS21E2

PMV Kit Remote controller "1:1 model" connection interface

3-2

BACnet R (*1)

TOSHIBA Digital Inverter System and Super Digital Inverter System

The local server should be connected to the BACnet network and the Mini-SMMS and Super MMS Super HRM system will be connected through the interface.

*1) BACnetTM: ANSI/ASHRAE 135-1995, A Data Communication Protocol for Building Automation and Control Networks.

5-9

Touch screen controller system


System diagram

Setup file (record in CF card)

Touch Screen Controller

Intelligent Server Intelligent Server Software


Ethernet connection RS-485 Control wiring

Control Maximum 512 indoor units

Switching HUB (Local Supply)

TCS-Net Relay Interface

Max. 64 indoor units Max. 16 Refrigerant systems per TCSNET relay interface

Control wiring

Maximum 4 Intelligent server Report Creation software (Excel macro)

RS-485 Control wiring

PC for Energy Monitoring (Local supply)

Maximum 8 TCS-NET Relay Interface RS-485

(Note) Switching HUB (10BASE-T compliant) is required when using two or more intelligent servers or when connecting a PC for energy monitoring and billing.

Maximum 4 Energy Monitoring Relay Interface

[ Power meter ] Local supply


1kWh/pulse or 10kWh/pulse 50-1000ms Maximum 8 Power Meter

I/F

Pulse Signal

Max. 32 (8 X 4) power meter per intelligent server

Energy Meter Relay Interface

RS-485

3-3
Fire alarm Door Key Entry ON/OFF Error code output

Maximum 4 Digital I/O Relay Interface


Maximum 8 digital inputs

I/F
Maximum 4 digital outputs

Digital I/O Relay Interface

Max. 32 (8 X 4) digital inputs Max. 16 (4 X 4) digital outputs per intelligent server

Model Name Touch Screen controller (English version)

Intelligent Server Intelligent Server Software TCS-Net Relay Interface Energy Monitoring Relay Interface Digital I/O Relay Interface (1) Monitoring air-conditioners

Model Name BMS-TP0640ACE BMS-TP5120ACE BMS-TP0640PWE BMS-TP5120PWE BMS-LSV4E BMS-STCC01E BMS-IFLSV1E BMS-IFWH3E BMS-IFDD01E

Specification Max 64 indoor units , without energy monitoring and billing Max 512 indoor units , without energy monitoring and billing Max 64 indoor units , with energy monitoring and billing Max 512 indoor units , with energy monitoring and billing Server in between Touch Screen controller and RS-485 Installed on Intelligent Server Interface between intelligent Server Control wiring(TCC-LINK) Interface for power meter Interface for input / output signal

Devices

Operation status can be viewed according to a unit. [Unit] All building, All tenants, Each tenant, Each area, Each remote controller group [Monitoring contents] Operation and alarm status, Setting status for each remote controller group Header / individual control can be performed according to a unit. [Operating contents] ON/OFF, Operation setting (operation mode, air volume, louver position, setting temp., restricted setting from remote location) Air-conditioners are operated according to the set-up schedule / operation pattern. Schedule opretaion can be performed according to a unit. [Operation pattern]Weekly pattern, special day pattern (4 pattern), Non-operation days pattern The present alarm contents are displayed. [Display contents] Alarm contents, Unit number, Generated time The alarm history records are displayed. [Display contents] Alarm contents, Unit number, Generated time Monthly report data is written to "Compact Flash". Monthly reports can be created according to a unit using the monthly report software. [Monthly report contents] The number of ON/OFF, Operating time, Results of energy monitoring according to a unit using the energy monitoring software. [Energy monitoring data] Power consumption according to the power meter

(2) Operating of air-conditioners

(3) Schedule operation

Function

(4) Alarm list display (5) Alarm record display (6) Monthly report data extraction

(7) Energy monitoring data extraction Power consumption data is written to "Compact Flash". Energy monitoring can be performed

5-10

5-2. Controller dimensions Wired remote controller


RBC-AMT31E

120 62 18 84 120

16

Note : All dimensions are in mm

Simple remote controller


RBC-AS21E2

120

80

60 70

13 16

Note : All dimensions are in mm

5-11

Wireless remote controller kit


TCB-AX21U (W)-E2

186 58 19.5

186

32

61

Note : All dimensions are in mm

RBC-AX22CE2

130 58 19.5

177

61

177

Note : All dimensions are in mm

5-12

65

Wireless remote controller kit


TCB-AX21E2

58

19.5

4.4 x 9.4 long hole 13

83.5

177

70

4.4 x 5.4 long hole

61

Note : All dimensions are in mm

Weekly timer
RBC-EXW21E2
2.7

120

16 120

Note : All dimensions are in mm

5-13

83.5

ON-OFF controller
TCB-CC163TLE2
116

Unit: mm
160 6
6

148

(6)

14

69

160

148

121

115

(6)

122

4-5 diameter holes (for mounting)


128 80

Hole for electrical wiring

128

80

36

47

4-5.5 diameter holes (for mounting)

Z-view (back side)

13

Note : All dimensions are in mm

5-14

Remote sensor
TCB-TC21LE2

120

80

60 70

13 16

Note : All dimensions are in mm

Central remote controller


TCB-SC642TLE2
116 47
15

160 148

13

21 (6)

69

160

148

121

115

(6)

121 128 80

128

80

36

47

Z view (back side)

13

Note : All dimensions are in mm

5-15

TCS-Net relay interface


BMS-IFLSV1E
200

6- 5.5 mounting holes 22 78 78 22

66 63.6

146.9

22

78

78

22

Note : All dimensions are in mm

Touch screen controller


BMS-TP0640ACE BMS-TP5120ACE BMS-TP0640PWE BMS-TP5120PWE

54 49

316 249 75

242

95.75

75

99.3

82.5 48
16

302 55.5
19 30

70

91.75

Note : All dimensions are in mm

5-16

256

156 170

Intelligent server
BMS-LSV2E

370
WARNING
Do not decompose.

Note : All dimensions are in mm

Energy monitoring relay interface/Digital I/O relay interface


BMS-IFWH3E BMS-IFDD01E
18

234

Grommet for power input


103.5

18

Grommet for power meter

92.5 (193)

Grommet for RS-485


53.5 64.5

18

220

18

246

63.6

Note : All dimensions are in mm

5-17

39

198
CAUTION

Do not remove.

LON GATEWAY
TCB-IFLN640TLE

234
18

Mounting hole 6-O / 5.5


18 78.5

78.5

18

78.5

220

63.6

246

Note : All dimensions are in mm

5-18

66

18

78.5

193

TOSHIBA CARRIER CORPORATION


2 CHOME 12-32, KONAN, MINATOKU, TOKYO, 108-0075, JAPAN

You might also like