Professional Documents
Culture Documents
CONTENTS
page page
TURN SIGNALS—XJ
Refer to Section 8W - Wiring Diagrams for cir- (2) Remove and inspect 20 amp #8 fuse. Replace if
cuit wiring diagram. necessary. If OK, go to next step.
(3) Remove turn flasher, light blue can, located in
DESCRIPTION upper left corner of fuse block.
With the turn signal lever in its up or down posi- (4) Turn ignition switch to ACCESSORY. Check
tion and the ignition switch in ACCESSORY or ON, for battery voltage at flasher bottom cavity on fuse
current flows through the: block. If OK, go to next step. If not, repair open cir-
• turn/hazard switch
cuit in wiring between turn flasher and #8 fuse.
• selected turn indicator bulb
(5) Turn ignition switch to ACCESSORY. Move
• front and rear turn signal bulbs
turn signal lever up or down. Replace turn flasher
• and the front side marker bulb.
with known good flasher. The lamps should flash. If
With the headlamps OFF, the turn and front side
marker lamps flash in unison. With the headlamps not, replace original flasher and go to next step.
ON, the turn and front side marker lamps flash al- (6) Turn ignition switch to OFF. Follow procedure
ternately. for turn/hazard switch replacement to locate steering
column connector. Unplug connector.
DIAGNOSIS—TURN SIGNAL INOPERATIVE (7) Turn ignition switch to ACCESSORY. Check
(1) A turn signal indicator that does not flash usu- for battery voltage at connector terminal L. If OK,
ally indicates a burned out turn signal bulb. Check replace turn/hazard switch and check that lamps
for and replace if defective. System should now func- flash. If not, repair open circuit in wiring between
tion properly. If not, go to next step. turn flasher and steering column connector terminal
High generator output voltage can burn out L.
lamps rapidly.
HAZARD LAMPS—XJ
Refer to Section 8W - Wiring Diagrams for cir- check underside of PDC cover. Replace if necessary.
cuit wiring diagram. If OK, go to next step.
(2) Remove hazard flasher (tin can) located in fuse
DESCRIPTION block.
With the hazard switch ON, current flows through (3) Check for battery voltage at the terminal on
the: the right (3 o’clock). If OK, go to next step. If not, re-
• hazard flasher pair open circuit in wiring between #F13 fuse and
• the turn/hazard switch hazard flasher right terminal.
• two front turn signal bulbs (4) Replace hazard flasher with known good
• two rear turn signal bulbs flasher. Activate hazard warning switch. Lamps
• two front side marker bulbs should flash. If not, replace original flasher and go to
• and two turn indicator bulbs. next step.
All of these bulbs will flash on and off. (5) Follow procedure for turn/hazard switch re-
placement to locate steering column connector. Un-
DIAGNOSIS—HAZARD LAMPS INOPERATIVE plug connector.
(1) Inspect 20 amp #F13 fuse in Power Distribu- (6) Check for battery voltage at connector terminal
tion Center (PDC). The PDC is located in the engine K. If OK, replace turn/hazard switch. If not, repair
compartment, passenger side. For location of fuse, open circuit in wiring between hazard flasher and
steering column connector terminal K.
8J - 2 TURN SIGNALS AND HAZARD WARNING FLASHER J
TURN SIGNALS—YJ
Refer to Section 8W - Wiring Diagrams for cir- (3) Remove and inspect 15 amp #4 fuse. Replace if
cuit wiring diagram. necessary. If OK, go to next step.
(4) Remove turn flasher, light blue can, located in
DESCRIPTION fuse block.
With the turn signal lever in its up or down posi- (5) Turn ignition switch to ACCESSORY. Check
tion and the ignition switch in ACCESSORY or ON, for battery voltage at cavity on left (closest to hazard
current flows through the: flasher can). If OK, go to next step. If not, repair
• turn/hazard switch
open circuit in wiring between turn flasher and #4
• selected turn indicator bulb
fuse.
• front and rear turn signal bulbs
(6) Turn ignition switch to ACCESSORY. Move
• front side marker bulb
turn signal lever up or down. Replace turn flasher
With the headlamps OFF, the turn and side
marker lamps flash in unison. With the headlamps with known good flasher. The lamps should flash. If
ON, the turn and side marker lamps flash alter- not, replace original flasher and go to next step.
nately. (7) Turn ignition switch to OFF. Follow procedure
for turn/hazard switch replacement to locate steering
DIAGNOSING—TURN SIGNAL INOPERATIVE column connector. Unplug connector.
(1) A turn signal indicator that does not flash usu- (8) Turn ignition switch to ACCESSORY. Check
ally indicates a burned out turn signal bulb. Check for battery voltage at connector terminal L. If OK,
for and replace if defective. System should now func- replace turn/hazard switch. If not, repair open circuit
tion properly. If not, go to next step. in wiring between turn flasher and steering column
High generator output voltage can burn out connector terminal L.
lamps rapidly.
(2) Locate fuse block under driver’s side of instru-
ment panel.
HAZARD LAMPS—YJ
Refer to Section 8W - Wiring Diagrams for cir- (2) Remove hazard flasher (tin can) located in fuse
cuit wiring diagram. block.
(3) Check for battery voltage at the terminal on
DESCRIPTION the left. If OK, go to next step. If not, repair open cir-
With the hazard switch ON, current flows through cuit in wiring between #F5 fuse and hazard flasher
the: left terminal.
• hazard flasher (4) Replace hazard flasher with known good
• turn/hazard switch
flasher. Activate hazard warning switch. Lamps
• two front turn signal bulbs
should flash. If not, replace original flasher and go to
• two rear turn signal bulbs
next step.
• two front side marker bulbs
(5) Follow procedure for turn/hazard switch re-
• two turn indicator bulbs.
All of these bulbs will flash on and off. placement to locate steering column connector. Un-
plug connector.
DIAGNOSIS—HAZARD LAMPS INOPERATIVE (6) Check for battery voltage at connector terminal
(1) Inspect 20 amp #F5 fuse in Power Distribution K. If OK, replace turn/hazard switch. If not, repair
Center (PDC). The PDC is located in the engine com- open circuit in wiring between hazard flasher and
partment, passenger side. For location of fuse, check steering column connector terminal K.
underside of PDC cover. Replace if necessary. If OK,
go to next step.
J TURN SIGNALS AND HAZARD WARNING FLASHER 8J - 3