Professional Documents
Culture Documents
Table of contents eAFK Feed systems Draw and texturing zone Heater / Cooling combinations Heater solutions Cooling combinations Twist insertion Quality management system Intermingling Take up zone Oiling solutions Take up solutions Cross sections eAFK standard eAFK coolex eAFK Multispindle eAFK HTI eAFK HTI coolex 1.0/1.2 active eAFK HTI coolex 1.0/0.8 active Plant Operation Center Upstream processes SUN Service Unlimited 4 6 7 7 8 10 12 13 14 15 15 16 18
24 25 26
efciency
excellence
enhancement
evolution
Feed systems
Godet feed unit The single driven godet feed unit as being used in G1, G2 and G2x has been derived as a principle from POY spinning. It has been introduced by Oerlikon Barmag in DTY machines in 2003. Optimized for the DTY process, it quickly convinced where highest requirements for yarn processing were key. The stress-free yarn transport offers advantages for both sides of the product spectrum. When producing ne denier products with high number of laments, it ensures higher yarn quality and extended yarn evenness over time. Friction-intensive products such as full dull or spun dyed, that usually quickly wear down those components they are in contact with, are processed with greater efciency and at lower production costs. This is rstly due to non-existent slippage and secondly due to the godet itself, which makes additional yarn-guiding elements or wear-reducing components such as yarn displacement in the yarn path, superuous. Other general advantages of godets include higher consistency over process time and from position to position as well as potentially lower energy consumption. By using godets energy savings of up to 5% can be achieved. Shaft feed unit The centrally driven shaft feed system at W3 fullls all the basic requirements for processing even delicate products from all kind of polymers. Yarn feed takes place in conjunction with nip rollers or if required aprons. For easy handling and maintenance, nip rollers are equipped with intermediate stop as well as quick release. With selection of latest materials the lifetime of coats are improved, which inuences maintenance cycles positively reduces down time increases machine efciency The feed unit W3 is standardly equipped with a yarn displacement system to reduce wear on coats.
Yarn treatment ++
Wear parts ++
Products Polymers +
Process exibility +
Pneumatic String up solution In order to string-up the machine, proper placement of the yarn in the heater and cooling are of importance. As standard, Oerlikon Barmag offers the eAFK with pneumatic string-up equipped with quick release function swivel arms that allow easy push in & out of twist stop rollers and yarn guides. The pneumatic string-up solution uses compressed air to move the function swivel arm into the top position by deploying a magnetic sledge, which also secures the positioning when in place. Easy operation by push buttons on each string up position make the pneumatic string up as operatorfriendly and process secure as possible.
Heater / Cooling combinations Dening the right heater/cooling combination for a certain production range is the best option for optimizing production. There are technological and physical limits to be considered. Technological limits depending on yarn product are: Surging Yarn tension Desired yarn quality Physical limits depending on yarn product are: Heat transfer of heating system Heat transfer of cooling system Friction
Depending on product titer and number of laments, the choice of heating in conjunction with cooling components can either improve the yarn quality or optimize the process speed or even both. A further high-impact effect of choosing the right option is the potential energy saving. Apart from optimizing the production, the energy saving reduces the total manufacturing cost, depending on the choice of heater. In todays demanding market, production optimization can be the difference between making prot or a loss. Oerlikon Barmags experience, technology, components and cross-sections provide our customers with the possibility of freely selecting the cross-section that allows ideal production, depending on product lowcost manufacturing of high quality products with the greatest-possible process efciency eAFK!
Heating solutions
First heater Dowtherm* Dowtherm contact heaters have been successfully used in Oerlikon Barmag machines for over 30 years now and are even today state-of-the-art technology, particularly for multi and microlaments. Anti-wear nitrated surfaces, deep V prole and special pinches for preventing yarn heat-outs result in high yarn cleanness, extremely even crimping and excellent dye uptake for the textured yarn. Oerlikon Barmag Dowtherm heaters are open close heaters for easier operation and maintenance, equipped with manually closing doors. They are available in various lengths suitable for processing different ranges of products. Depending on the product portfolio customers can optimize their production with the right selection and combination of heater and cooling component. The correct selection of these components can inuence production speed and capacity energy consumption yarn quality
HTI The HTI high-temperature heater makes it possible to achieve high speeds coupled with excellent yarn qualities due to stable yarn path and uniform heat transfer. The 1 m long heater consists of two heating zones that, equipped with special exchangeable inserts developed and patented by Oerlikon Barmag enable fast and simple replacement during standard maintenance work. This increases overall machine efciency by minimizing idle machine time resulting from maintenance and cleaning. The inserts are cleaned outside the machine, hence eliminating the customary problems associated with heater cleaning. Inserts are available for both heating zones, either with pinches or as full contact inserts. Different inserts can be combined for optimization of the process, catering to the special needs of highly critical products. Due to its design, the Oerlikon Barmag HTI heater has signicantly lower energy consumption in comparison to its Dowtherm cousin. This - combined with signicant potential process speed increase makes the HTI heater is a worthwhile alternative investment consideration.
Heater Type
Heater length
Energy saving
Yarn treatment
Typical application
HTI
1.0 m
30 300
++
++
All kind of yarns depending on insert type and combination Fine yarn, micro and multilament Average commodities
DTH
1.5 m
20 200
20 150
PET, PA, PP, PTT PET, PA, PP, PTT PET, PA, PP, PTT
DTH
2.0 m
30 300
30 200
DTH
2.5 m
70 600
150 600
Coarse
Secondary set heater Dowtherm* Dowtherm set heaters with tubes generate evenlyset yarns and can be adapted in process by means of exchangeable tube inserts available in various designs spiral pinched, half spiral pinched or at. Depending on process and product, the Oerlikon Barmag-developed solution allows yarn optimization in terms of loop-free yarns, a particularly important feature for multi- and microlament yarns. As standard, the heater is 1.30 m in height and available in standard and low-temperature versions for set treatment of highly-critical yarns. Secondary heaters are used for differential production on either side of the machine.
Cooling solutions
Depending on product and process, the right combination of heating and cooling components is important for an optimized yarn production crucial in todays demanding markets. Oerlikon Barmag offers a variety of cooling components that are designed to work in harmony with our heater products. Plate Cooling plates have been developed by Oerlikon Barmag in line with the heaters. Respectively they offer the same process relevant features such as anti-wear nitrated surfaces, deep V prole and special pinches for preventing yarn cool-outs. Cooling plates are available in various lengths to allow optimal heat transfer, depending on the product.
Cooling length
Yarn treatment
Usually in combination with heater 1.5 m DT* 2.0 m DT* 1.5 m DT* 2.0 m DT* 2.0 m DT*
Typical application
0.70 m
20 150
++
PA, PP, PTT 20 70 PA, PP, PTT 20 100 PET, PA, PP, PTT 30 200 PET, PA, PP, PTT 30 300 PET, PA, PP, PTT
Fine yarn, micro and multilament Fine yarn, micro and multilament Average commodities
0.85 m
20 200
20 150
1.10 m
30 300
30 200
1.75 m
30 300
30 300
2.10 m
100 600
150 600
--
10
Tube Cooling tubes have been developed by Oerlikon Barmag in response to rising requirements in downstream texturing in regard to process speed and friction. By using specially treated tubes Oerlikon Barmag developed cooling components that cover a wide range of products, eliminate cool-outs and offer improved process speeds due to reduced texturing zone length. The tubes are cooled by ambient air, but can also be connected to an air conditioning system to increase their cooling effect so called active cooling for an even wider range of applications.
Cooling length
Yarn treatment
Typically used for polymer/ den PET, PA, PP, PTT 20 200
Typical application
0.80 m
20 300
++
Fine yarn, micro and multilament High speed Low friction Fine yarn, micro and multilament Commodities, High speed
1.20 m
30 600
70 300
1.0 m HTI*
11
Twist insertion
Oerlikon Barmag has apart from the early days of texturing machinery always focused on friction disc units as the most advantageous and exible form of twist insertion. Using different types of friction working discs as well as specially developed inlet and outlet discs the friction units can be adapted to any kind of product for optimal production. For eAFK the standard is the Oerlikon Barmag friction aggregate type 8E, which has been developed to fulll the highest quality demands within the texturing process. Using synergies within the Oerlikon Textile group the open close friction aggregate FTS 53 has been mutually developed with Oerlikon Textile Components. Both friction aggregates share the same single driven housing, are interchangeable and as such provide customers additional exibility for optimization of process.
Both texturing units have the following characteristics in common: High exibility for a wide range of products from ne 20 denier up to coarse denier of 600 den Designed for a maximum stacking of 10 discs with 9 mm thickness or 13 discs with 6 mm thickness Elastic and mufed high-speed bearings for extra low vibration at high speeds (up to 22,000 rpm) Low noise level Low variation of disc speed Lower energy consumption No displacement of texturing unit and entrance guide at S/Z switching Easy reversal of twist direction Easy removal of friction unit for maintenance purposes
The individually driven type 8E texturing unit comprises a xed center design, which adds to the general characteristics, extraordinary sturdiness and lifetime evenness.
The aggregate FTS 53 simplies string-up as a result of its open-close function. When placing the yarn into the aggregate, it can be single-handedly opened and closed once the yarn is secured in the center. Thus, it potentially improves string-up of very sensitive or complicated yarns.
12
With rising quality requirements, the demand for online quality monitoring systems is also increasing. The target is not only monitoring the draw-texturing process, but also improving the overall process and increasing machine efciency. With Oerlikon Barmags online quality monitoring, products that do not meet set quality standards are easily identied, withdrawn from the production process and replaced by yarn that meets the quality requirements. Hence, machine efciency is increased valuable machine time is not used to process yarn that does not meet the required standards!
Fibrevision Unitens The UNITENS concept in the latest generation of the unique combination of oating mean value, peak detection and CV evaluation, results in the highest standards in online yarn quality control, statistics, quality and plant management. As an integral part of the eAFK, UNITENS offers - in addition to the basic yarn quality evaluation and quality grading of the produced yarn - essential data for the highest dofng performance, the best machine service and maintenance, all resulting in the highest machine efciency and productivity. The sophisticated, but easy-to-handle UNITENS can be combined with Oerlikon Barmags Plant Operation Center (POC) software networking solution as well as with our CreelManager system.
CreelManager The close link between UNITENS quality evaluation and Oerlikon Barmags CreelManager opens up for the very rst time the possibility of production and classication of knot-free yarn packages, especially advantageous in conjunction with the automatic dofng function of the eAFK. The UNITENS system connected with the CreelManager represents a milestone in modern quality monitoring. The package quality information is considerably improved, which creates competitive advantages for manufacturers. With the help of special sensors in the creel, the UNITENS system is provided with information about supply package change. Hence, this information - with the knowledge about the supply package - can trace issues back as far as individual spinning positions, which for the rst time allows operators to monitor not only the performance of the DTY machine, but also of the prior production step in POY spinning. The objective of the system is to integrate the entire process chain into a total quality system (TQM). eAFK Oerlikon Barmag 13
Intermingling
Intermingling of yarn and there especially the number and regularity of the intermingling knots are one of the prerequisites for high end downstream operation. Oerlikon Barmag in close cooperation with world renowned brands for intermingling jets offers with the eAFK machine a wide range of intermingling possibilities throughout the process. Intermingling is an option that depending on downstream requirement has to be discussed.
Pre-intermingling While processing ne denier and especially highlychallenging microber with high number of laments, pre-intermingling can be an attractive solution for improving the quality of the nal yarn, overcoming manufacturing problems and increasing overall machine performance. Furthermore special products manufactured with special intermingling jets can create competitive advantages. The eAFK machine offers the possibility for implementing the intermingling piping required for pre-intermingling at the rst feed. Intermingling Regular and high quality intermingling is crucial to success especially for downstream weaving applications and here for warp yarns. To achieve the best-possible intermingling, the Oerlikon Barmag eAFK includes the so-called intermingling zone upstream to the secondary heater. It comprises two feed systems (G2 and the additional G2x) that allow stable and controlled yarn processing within a dened 14 eAFK Oerlikon Barmag
area. The integrated intermingling piping, equipped with straight couplings, offers easy handling and operation of the respective jets. Detorque In the event that customers wish to produce close to zero torque yarn without the need to ply yarns, Oerlikon Barmag offers a detorque intermingling system for the eAFK. Located between the secondary heater and the third feed unit the intermingling piping can be equipped with special jets that create a yarn that is not completely without torque, but with minimal torque. Detorque works only with PET and requires a set heater. It is an alternative to plying yarns, which reduces the takeup capacity of the respective DTY machine by half (for 2-ply), in the event that the yarn is plied on conventional rather than Multispindle machines.
Take up zone
Oiling solution single deck
The application of oil is important for smooth operation throughout most processes within the textile process chain. Depending on the downstream setup, a certain amount of oil may be required for higher efciency and less disruptions. Oil applied in one step of process is usually consumed or eliminated during the following process step, only again to be applied if required in the next step. For some products and downstream processes, oil is particularly undesirable, as in the case of dyeing applications, for instance. Respectively, a certain technical exibility must be considered. The location of the oiling device, the form of oil application and the polymer type can inuence the process and are therefore important for efcient operation and high-quality production.
Single deck oiling is standard for the eAFK. Small and tightly covered oil troughs are located in front of each take-up deck. The latest-technology application rollers with a V groove along the yarn path apply the oil depending on stepfree setting of rotation speed. This solution allows the most accurate oil application, while simultaneously eliminating staining caused by potential oil mist.
Pneumatically actuated, the yarn is either being lifted out of the oil applicator during dofng for oilfree transfer tails or can be xed in this position for completely oil-free packages (e.g dye packages). The eAFK with single deck oiling provides the most even process conditions from package to package as well as from deck to deck, thus improving the overall production quality.
15
Take up solutions
With the further development of downstream processes, the requirements for the DTY package constantly increasing. The best-possible package formation and the related unwinding performance are decisive criteria for efcient manufacturing with up-to-date technology. As standard, the eAFK is equipped with ATT (Advanced Take-up Technology), the latest technology for advanced density controlled package formation, in conjunction with an automatic dofng unit.
ATT Advanced Take up Technology The quantum leap in package building technology comes with a single-position drive solution, fewer mechanical components and computer-control of every single stroke throughout the package formation, providing signicant benets for the manufacturer and for the product itself. Furthermore, ATT allows for special solutions, such as unique exibility in package geometry or quality indicating marking of packages, which have until now been impossible using mechanical take-up units. The individual position drives in process and maintenance increase the exibility during production and prevent unnecessary machine downtimes. A signicant lower noise level and a reduced number of mechanical parts, easy maintenance and improved accessibility round off the mechanical improvements achieved by ATT. Another highlight is the control of yarn tension during winding. In detail, this means the yarn tension prole during winding cycle can be preselected in order to actively control the decrease in winding tension gradually lower the decrease in winding tension even down to a constant winding tension higher package weight even package density prevention of yarn damage by reduced initial winding tension unique features for winding dye packages A further feature is the choice of various take-up programs with an individual calculation of each stroke for even yarn distribution over the entire width of the package as well as uniform pressure distribution on the tube.
16
IAD Individual Automatic Doffer The further-improved individual automatic doffer of the eAFK is the culmination of Oerlikon Barmags experience in automatic dofng. Reliable dofng performance to ensure the highestpossible machine efciency is the result of a sturdy take-up section in low-vibration design combined with Oerlikon Barmags CPC (contact pressure control) bobbin lever system. Adjustable for different package densities, it allows in conjunction with the Oerlikon Barmag TUP (Take-up Processor) - the best-possible package formation with excellent take-off performance. During the dofng procedure, waste injector systems transport waste yarn into easily accessible bins located on the creel side of the machine. Apart from the considerably reduced noise level due to use of the ATT system in the take-up section, the basic functionality of the IAD is the production of packages of uniformly-metered length. Two parking positions, in conjunction with one further full package in production, allow unattended operation for longer periods of time, depending on yarn titer. The eAFK take-up solution with ATT and IAD provides Positions: up to 288 pos CPC bobbin lever system Winding of taper-ended packages with nominal taper angles of 65- 90 Max. package diameter - 250 mm Basic (max.) traverse stroke length - 250 mm (273 mm) Max. double strokes per minute 800 Package formation Traverse drive with ribbon breaking unit as well as with scattering system variable for highest process speeds Automatic dofng Two parking positions
Take up
Taper angle ++
Maintenance
ATT
++
17
Cross sections
Although the eAFK allows a high exibility in conjunction with components, some cross-sections have proven to be the most suitable options for certain products and processes. For processing of ne to mid or mid denier with high number of laments, the V cross-section has been most successful. When processing such yarns, length of texturing zone, suitable heating-cooling combination and friction are to be considered. Various combinations are available using Dowtherm and HTI heater technology. For mid to coarse denier depending on number of laments and nal product requirement V or M crosssection can be selected. V type is more suitable for the mid, whereas M type is clearly more suitable for coarse denier with low number of laments. When selecting the components required for such product portfolio also the right choice of feed system has to be put into consideration. For coarse to heavy denier the M type upper structure is the most suitable crosssection for processing products with high denier per lament and total denier. As feed system shaft with nip roller due to draw forces implemented by coarse products has to be selected. The eAFK is designed to process all kinds of polymers in best possible manner. For polymers that typically do not require heat setting such as PA or PP can similarly well processed on the following cross-sections by minor changes to the machine: the secondary heater is being substituted with yarn guiding elements.
Process
Products mid 75-150 ne 50-75 Dpf coarse 220-300 high mid 150-220 exibility Advantage
eAFK
very ne 20-50
0.2-0.5
1.0-5.0
standard coolex Multispindle HTI HTI coolex 1.0/1.2 HTI coolex 1.0/0.8 PA standard PA coolex
18
special
0.5-1.0
energy saving
quality
speed
19
Dowtherm* upper structures Fine to conventional denier, versatility, process speed, PET/PA/PP/PTT/PLA eAFK standard: V 2.0 DT/ 1.1 P The most versatile conventional cross-section using Dowtherm heater technology. Comprising a 2.0 m heater in combination with a 1.1 cooling plate this V cross-section combines versatility and a wide operational window. It is suitable for most commodities in a range between 30 to 300 den with best operational range between 50 and 220 den. Comprising the straight yarn path of the V cross-section low tension and high draw ratios can be achieved resulting in excellent manufacturing speeds, making this cross-section a standard in the industry.
Versatility for efcient and high quality production is achieved by reduced friction elimination of contact points implementation of heater and cooling with greater operational window straight yarn path
Suitable for micro lament yarns and ne to mid denier, while allowing greater operational window for higher denier
eAFK coolex: V 1.5 DT/ 0.8 T The coolex upper structure is optimized for processing very ne denier or products with very low lament count by means of a shorter Dowtherm heater in combination with a 0.8 m cooling tube. The 1.5 m heater allows energy savings of up to 15% in comparison to the 2.0 m version. The 0.8 m cooling tube provides increased cooling capacity on shorter length and can be further optimized according to product requirement by adjusting the wrapping angle. This results in an operational window that especially favors ne denier and allows to process products even down to 20 den at even higher process speeds than the standard cross section.
Improved processing of very ne and micro yarns is achieved by... optimized heater length improved and exible cooling shortest possible texturing zone less stress to yarn with selected components
Suitable for super micro lament yarns and very ne to ne denier, opening operational window for these products while contributing energy saving
eAFK Multispindle: V 2.0 DT/ 1.1 P x 2 The Multispindle upper structure allows processing double the number of yarn ends for production of non-torque yarns in a product range of ne to mid denier with low to conventional lament count. While plying yarns on conventional machines the take-up capacity is reduced by half, thus increasing the number of yarn ends for treatment before being plied doubles the take-up capacity. Prerequisite for such processing is the limitation of single yarn ends to 220 den considering the nal denier of the plied yarn. This results in an operational window that favors ne to mid denier including low single lament yarns.
Improved processing of plied ne to mid denier yarns is achieved by doubling the number of yarn ends per heater doubling the number of cooling plates doubling the number of texturing positions Suitable for micro lament yarns and ne to mid denier, opening operational window for plied products
21
HTI upper structures Optimized operation window and versatility, highest process speed, PET/PP/PTT/PLA eAFK HTI: V 1.0 HT/ 1.75 P To widen the operation window the electrical HTI heater can be used. With its temperature range of up to 550C in addition to exibility provided by Barmags patented insert technology it allows to process yarns at potentially higher process speeds. In order to compensate for the temperature increase the cooling capacity has to be adapted proportionally. The conventional HTI version comprises a 1.75 m cooling plate which provides a cooling capacity that allows to process ne to mid denier at highest possible process speeds. Versatility for efcient and high quality production at highest process speeds is achieved by increased heating capacity increased cooling capacity opening the operational window while shortening the texturing zone to 2.75 m straight yarn path
Suitable for ne to mid and coarse denier in the range of 30 300 den with an optimized operational window
22
eAFK HTI coolex 1.0/1.2 active: V 1.0 HT/ 1.2 T To further widen the operation window the HTI heater is paired with Barmags cooling tube technology, that while shortening the texturing zone increases the cooling capacity beyond the capacity of the 1.75 m plate for the most demanding products. The ambient air cooling effect can be boosted with activation of air conditioned cooling thus allowing to optimally process products with different processing requirements exibly and by elimination of all bottle necks with the highest possible process speed exceeding the conventional HTI version.
Versatility for efcient and high quality production at highest process speeds is achieved by increased heating capacity increased cooling capacity with active air cooling option opening the operational window while shortening the texturing zone to 2.2 m straight yarn path Suitable for ne to mid and coarse denier in the range of 30 300 den with an optimized operational window
eAFK HTI coolex 1.0/0.8 active: V 1.0 HT/ 0.8 T Similarly to the Dowtherm heater coolex version the HTI heater can be paired with the shorter cooling tube of 0.8 m length. Although decreasing the cooling capacity limits the operation window the shortening of the texturing zone leads to optimization for very ne denier and super micro yarns. The limitation is partially compensated with the also in this version available active cooling technology.
Versatility for efcient and high quality production at highest process speeds is achieved by increased heating capacity optimized cooling capacity with active air cooling option optimizing the operational window while shortening the texturing zone to 1.8 m straight yarn path
Suitable for very ne to mid denier in the range of 20 200 den with an optimized operational window
23
The POC creates transparency - the Job Reports module (Bild TEX JobReport1.tif) The POC Job Reports gives us an up-to-date and exact summary of all manufacturing jobs in the line. The summary includes information on both, complete manufacturing jobs and those still running. These informations are refreshed with each doff and for each package, respectively. Consequently, they are very precise at any time. The corresponding views show the current information per job, per machine and per position. As an option the POC interface to ERP can be used to forward the data of already nished manufacturing jobs to a customer ERP system.
The POC simplies the workow - the Recipe Management module (Bild TEX Recipe Management.tif) The POC Recipe Management provides a central plant wide management of recipes. With the POC Recipe Management machine settings can be stored and transferred to recipes. Those recipes can be archived, printed, validated, edited, and then downloaded back to any machine connected. The Recipe Management automatically checks, if the desired set of information matches the physical arrangement. The POC Recipe Management has to be part of the system, if a connection to ERP (e.g. SAP) systems will be implemented, as it is the interface between an order/offering system and the real process settings for the machines.
24
Upstream processes
Consulting, engineering, plant construction and high-tech machinery the whole package from a single source. Many years of experience in textile machine construction and Oerlikon Textiles strong global network form a solid basis and the perfect prerequisites for Oerlikon Barmag as a solutions provider. Plant engineering The growing demand for engineering services particularly from various newcomers to the ber/lament manufacturing and processing sector - has resulted in the setting up of an Oerlikon Barmag-internal engineering division. A harmonized chain of polycondensation, spinning and texturing machines allows efcient production which results in an increase of added value for the customer. Furthermore, Oerlikon Barmag will cater for a harmonization of all machines and lines in an optimal way and will provide the respective know-how. Polycondensation systems The quality of raw materials is a decisive factor in the quality of the nal product. Only vertically-integrated companies control all levels of the value-added chain, all others are reliant on their suppliers. With Oerlikon Barmag polycondensation, the yarn producer will reduce dependencies and will be able to determine the characteristics of the raw material. With more than 80 years of experience, Oerlikon Barmag knows the requirements of lament spinners and converts them into process-optimized systems concepts. POY spinning With more than 30,000 spinning units supplied in the last 10 years, POY systems are the most successful Oerlikon Barmag product. Several decades of continuous research and development today allow all customers to produce the most varied POY laments efciently and cost effectively. Oerlikon Barmag POY systems supply the best package quality and thus guarantee the highest pull-off speeds and an excellent dyeability of standard titers, microlaments and high-count yarns.
25
business units and their product lines. Our customers have online access to the latest documentation, tailor made for their machines The trouble-shooting manual permits a quicker and more efcient elimination of problems via direct links. The SECOS e-Commerce system, well-known worldwide, is completely integrated. The Engineering tool supports and accompanies the entire engineering process from concept to the turn-key plant. Innovative ideas and new solutions are added continuously. The latest encryption technology guarantees the maximum data security at any time.
26
27
Oerlikon Barmag Zweigniederlassung der Oerlikon Textile GmbH & Co. KG Leverkuser Strae 65 P.O. Box 11 02 40 42862 Remscheid GERMANY Phone +49 21 91 67-0 Fax +49 21 91 67-12 04 info.barmag@oerlikon.com Oerlikon (China) Technology Co., Ltd. No.9 Chang Yang Street Suzhou Industrial Park Jiangsu, 215024, P. R. China Phone +86 512 8188 5902 Fax +86 512 8188 5988 dty.info.barmag@oerlikon.com dty.service.barmag@oerlikon.com
The information supplied in this brochure is for guidance only. We reserve the right to modify it at any time. TL-eAFK 11/06-1 yaean design limited Subject to changes