Professional Documents
Culture Documents
AIMS : 1. To Design the Rectangular Pressed Steel water tanks as per Codes IS 804-1958 and IS 800-1984 2. To Calculate the loads and Designing the Gantry Girder 3. To Design the shear Connections and Composite beam connections 4. To Calculate the Live Loads and Wind Loads on trusses as per IS codes and Designing the Various elements in Roof Trusses as per IS 800 and IS 875 5. To Design the Plate Girder of Welded type and Riveted type 6. To Design the Deck type Railway Plate girder Steel Bridge, Bridge bearings, Rocker bearings and Roller bearings
OBJECTIVES: This Subject is an extension of learned chapters in 1st semester. It deals with application of various theories explained in previous semester. Analysis and design of various industrial structures will be covered with illustrative examples. Additional references will be given at the end of each chapter. Clarifications ill be given in all tutorial classes and chamber consultancy and colloquia hours for all doubts etc., Additional advanced topics will be covered in extra classes allotted.
UNIT 4 5. PLATE GIRDER: Introduction; Elements of plate girder; Weight and economic depth of plate girder; Design of web; Design of flanges; Curtailment of flange plates; Intermediate
vertical stiffeners; Horizontal stiffeners; Bearing stiffeners; Web splice; Flange splice; Connections; Design of riveted plate girder; Design of welded plate girder.
UNIT 5 6. STEEL BRIDGES: Introduction to Steel bridges; Railway broad gauge loading and I. R. C. loadings; Permissible stresses; Bridge bearings, their types and applications; Design of rocker bearings and roller bearings; Design of Deck type Railway plate girder bridge.
NOTE: Two questions of 14 marks each will be given from each unit out of which one is to be answered.
Text Books Prescribed 1) Design of Steel Structures by Anand S. Arya & J.L. Ajmani Nemchand & Bros, Roorkee. References: 1) 2) 3) Design of Steel Structures by S.K. Duggal. Design of Steel Structures by S. Ramachandra Vol. II. Design of Steel Structures by Vazirani and Ratwani
ASSIGNMENT SCHEDULES 1st Assignment 2nd Assignment SESSIONAL SCHEDULES 1St Sessional 2nd Sessional : : 11-01-2007 23-03-2006 : : 20-12-2006 15-02-2007
1. Design an elevated pressed steel tank having capacity of 125000L. The height of staging is 15m. Design of staging is not necessary. 2. Design a rectangular pressed steel tank for a capacity of 150000L. The tank is to be placed at a height of 12m above the ground. (Design of staging is not required) 3. A rectangular steel water tank is of dimensions 8 m length X 6 m wide X 4 m height. The tank is situated at a height of 12 m above the ground. Design a suitable staging for the tank assuming a wind pressure of 1.5 kN/m2. 4. Design a rectangular pressed steel tank 7.5m x 6.25 m x 2.5 m deep supported at 9m above ground level. Design tank bearers after planning the arrangement of the plate. 5. Explain the various components of a pressed steel tank. 6. Explain the various precautions you would take while constructing a pressed steel tank. 7. A steel water tank 7.5m x 5m x 2m (deep) is kept over a staging of 8m high. The tank is situated in coastal area top tier beams are ISLB 550. Assume FOUR columns.
1. Design a simply supported gantry girder of span 15m and carrying maximum wheel reaction each equal to 80 KN. Assume the wheel base is 3m. Use the provisions of EOT crane. 2. Design a composite foot bridge having clear span of 2.5m and width of 2.5m. The width of support is 0.3m. The bridge is to be designed as 4000 N/mm2. Use M 20 concrete. 3. A Howe type roof truss is to be designed for a clear span of 24 m with upper chord divided into six equal panels to serve as a roof for a laboratory at Delhi. The truss is to be supported on brick walls. The building height is 10m. The roof covering wall consists of corrugated fibre sheet. Compute live loads, dead load and wind load for their combinations. Consider medium permeability. 4. Explain the procedure in the design of a) Design of composite beam b) Shear connectors c) Various checks required 5. Design a roof truss for a factory building for a span of 20m and a pitch of 1/5. The height of the truss at every level is 10m. The spacing of the trusses is 4.5m. the factory building is 36m long is situated at Guntur. Use fy = 250 N/mm2. Use fink roof truss.