Professional Documents
Culture Documents
Page i
Page ii
Table of Contents
1. RADIO NETWORK PLANNING..........................................................................................3
1.1 1.2 2.1 2.2 PATH LOSS BASED APPROACH ............................................................................................. 5 SIMULATION BASED APPROACH ......................................................................................... 8 UPLINK LINK BUDGET .......................................................................................................... 12 DOWNLINK LINK BUDGET ................................................................................................... 19
2 3 4 5
LINK BUDGET .....................................................................................................................11 LTE LINK BUDGET EXERCISE .......................................................................................23 LTE COVERAGE SCENARIOS .........................................................................................26 LTE COVERAGE IN NOISE LIMITED SCENARIO ......................................................26
DEFINATION OF AVERAGE SNR ......................................................................................... 26 REQUIRED SINR ...................................................................................................................... 27 INTERFERENCE ....................................................................................................................... 30 COVERAGE-BASED SITE COUNT ...................................................................................... 31 AVERAGE CELL THROUGHPUT CALCULATION ............................................................. 33 SENSITIVITY ............................................................................................................................ 35
5.1 5.2
5.2.1
6 CAPACITY PLANNING .......................................................................................................33 7 LTE KEY PERFORMANCE INDICATORS FOR LTE RF DESIGN .............................36
7.1 Reference Signal Received Power (RSRP):- ...................................................................... 36 7.2 Reference Signal Received Quality (RSRQ) :- ........................................................................... 36 7.3 Overlapping Zones (Number of Servers):- ........................................................................... 39 Design KPI for Overlapping Zones (Number of Servers): ............................................................. 40 7.4 DL Cell Aggregate Throughput .............................................................................................. 40 9.1 9.2 9.3 9.4 9.5 Enhancing cell Edge Performance using ICIC........................................................................... 42 Cell-Edge SINR from Simulation, Trial and Real-Life Networks .............................................. 42 Effects Caused by Mobility:- ...................................................................................................... 45 Radio Link Failure and PDCCH Performance ............................................................................ 49 Inter-Cell Interference Coordination (ICIC) ............................................................................... 53
10 CELL EDGE THROUGHPUT ............................................................................................56 11 VOIP CAPACITY CALCULATION ..................................................................................58 12 REFERENCES .......................................................................................................................60
Revision History
Name
Ajay Chhalotre
Date
27 May, 2013
th
Version
1.01
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|3
Radio network planning is used to identify the geographic location soft heeNmkB. It is also used to identify the associated antenna configurations in terms of antenna type. height, azimuth and tilt The high level interaction of radio network planning with dimensioning, site acquisition. site design and site building is illustrated in figure 1
Figure 1
Radio network planning is preceded by system dimensioning. Dimensioning results are used to generate an estimate of the expected site density. This provides a guide to the number of sites required to achieve the target coverage and capacity Site acquisition defines the actual sites which arc available to the radio network planners. The site acquisition team may provide radio network planners with a list of candidate sites. Alternatively .radio network planners may identify the requirement for one or more sites at locations where there are currently no candidates Sites represent a relatively expensive investment for the operator. Selecting sites which have a poor location or which limit good site design can lead to reduced system performance irrespective of any subsequent RF and parameter optimization Evaluating candidate sites should involve a site visit as well as modeling within the radio network planning tool. In practice, the interaction between site acquisition and radio network planning is likely to be a compromise between obtaining ideal site locations and the actual locations which are available If an operator has already deployed a 2G or 3G network then it is likely to be beneficial to re-use as many of the existing site locations as possible .Re-use of existing sites introduces the option of sharing antenna sub-systems between 2G, 3G and LTE, i.e. feeder cables and Antennas can be shared.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|4
A potential drawback associated with sharing antennas is that it may limit the radio network planner's ability to apply independent 2G, 3G and LTE RF optimization. e.g. .if the LTE system requires mechanical antenna down tilt, then 2G and 3G systems must also be evaluated Site selection should also account for site design requirements. Site design involves identifying specific locations for the eNodeB cabinet and antennas. It also involves identifying the route for the feeder cable to connect the eNodeB cabinet to each antenna. The feeder cable should be routed as directly as possible to help reduce its length and minimize feeder losses Antenna placement represents the part of site design which has a direct impact upon radio network planning:
o
Antennas should not be placed behind any obstacles. Roof-top site designs should ensure that antennas are either at the edge of the roof-top or sufficiently high to avoid the edge of the roof-top clipping the antenna gain pattern If antennas are mounted on the side of a building then the azimuth requirement should be considered to ensure that the wall of the building do not shield the horizontal beamwidth If site is already accommodated with other antennas then the physical separation to those antenna should be considered to avoid interference
There are 2 fundamental approaches to radio network planning - Path Loss Based approach and Simulation Based approach o the path loss based approach is relatively simple and allows the radio network to be planned without modeling any subscriber traffic. This approach uses link budget results to define minimum signal strength thresholds. Results are typically presented in terms of service coverage and best server areas
o
The simulation based approach is more complex and time consuming but generates a greater quantity of information. Simulations are typically based upon static rather than dynamic simulations. Results can be presented in terms of coverage, cell and connection throughputs, transmit powers, interference levels
Simulations may be used to supplement the path loss based approach. In this case, the main planning activity is completed using path [ass calculations while simulations provide additional and more detailed information for specific sections of the network
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|5
Figure 2
The LTE site data should include site locations, antenna types, antenna heights, antenna tilts, antenna azimuths, feeder types, feeder lengths, RF carrier and eNode B types The propagation model should be tuned from measurements. Accurate propagation modeling is fundamental to radio network planning. Propagation model tuning involves minimizing the standard deviation of the error between the predicted and measured propagation loss while maintaining a mean error which is close to 0 Db A different propagation model can be defined for each environment type. Environment dependant correction factors can be applied to a common propagation model. Different propagation models can also be defined for different cell ranges, antenna heights and operating bands The digital terrain map should be adequate in terms of resolution, number of clutter categories and accuracy. The resolution should be relatively high for urban and suburban areas but can be reduced for rural areas. The appropriate number of clutter categories depends upon the geographic area. If the number of categories is large then the propagation tuning exercise becomes more difficult If rnicrocells or picocells with below roof-top antennas are to be planned then it may be necessary to purchase a map-which includes building vectors. Building vectors can be defined in either two-or three dimensions
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|6
The signal strength thresholds should be based upon a link budget analysis. Link budgets can be used to generate a set of maximum allowed path loss thresholds for a range of target throughputs within each environment type. In general, planning tools display contours of downlink signal strength rather than downlink path loss. This makes it necessary to translate the maximum allowed path loss into a minimum allowed signal strength A relatively arbitrary base station transmit power can be selected and the signal strength thresholds calculated by subtracting the maximum allowed path loss. The transmit power could be set equal to the cell specific reference signal transmit power per resource element. This allows signal strengths calculated by the planning tool to be interpreted as RSRP (Reference Signal Receive Power) An example of the translation from a link budget maximum allowed path loss to a planning tool signal strength threshold is presented in table 1. In this example, the downlink transmit power is based upon a total downlink transmit power capability of 43dBm and a channel bandwidth of 20 MHz (1200 Resource Elements), i.e. the cell specific Reference Signal transmit power per Resource Element is 43 10 x LOG (1200) = 12dBm (assuming equal transmit powers for all Resource Elements) Table 1 assumes that the maximum allowed path loss from the LTE link budget is.145 dB. This figure could have originated from either an uplink or downlink link budget. In both cases, the planning tool is used to display contours of down link signal strength, i.e.' signal strength is used to quantify path loss
Table 1
Calculating the planning tool signal strength threshold also requires consideration of the antenna gains and feeder loss values assumed in the link budget. The planning tool will apply its own antenna gains and feeder loss values which can be site specific and may not equal the values assumed in the link budget The antenna gain values assumed in the link budget can be removed from the maximum allowed path loss result, so the planning tool is able to apply its own values on a site by site basis, This is done by subtracting the link budget antenna gain values from the maximum allowed path loss
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|7
Handling feeder loss values can be more complex: o o if feeder loss values within the planning tool are set to 0 dB then the maximum allowed path loss does not require any feeder loss adjustment If feeder loss values within the planning tool are set to their actual values then tile link budget feeder loss should be added to the maximum allowed path loss result. This will generate only an approximate result if the link budget analysis resulted in uplink limited coverage with the use of Mast Head Amplifiers (MHA). The result is approximate because the maximum allowed path loss generated by the link budget is independent of the feeder loss(assuming the MHA exactly compensates the feeder loss) while the signal strength calculated by the planning tool is dependent upon the feeder loss
The resultant planning tool signal strength threshold in table 1 is calculated as the downlink transmit power,-- the adjusted maximum allowed path loss, i.e. 12 - (145 - 18 - 0 + 2) = -117 dbm The path loss based approach to radio network planning should include an analysis of the best server areas, This helps to ensure good dominance and a relatively even distribution of network loading, Best server areas should be contiguous and should not be fragmented. Non-contiguous best server areas indicate that there is likely to be relatively poor dominance and increased levels of inter-cell interference. In general, neighboring best server areas should be of approximately equal size. If there is a known traffic hotspot then an eNode B should be located as close as possible to that hotspot and the dominance area can be smaller
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|8
Figure 3
Both the static and dynamic simulations referenced above are system level simulations rather than link level simulations. The results from link level simulations usually form an input to system level simulations, e.g. the system level simulation look-up table defining the relationship between throughput and signal to noise ratio originates from link level simulations System level simulations model the network at a relatively high level. UE and BTS physical locations are modeled along with their antenna gains, transmit powers and noise floors. System level simulations do not model the transfer of individual modulation symbols. Static simulations calculate the signal to noise ratio conditions and subsequently look-up a corresponding throughput. Dynamic
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
|9
simulations may model the transfer of individual transport blocks and then use look-up tables to determine the probability of successful reception Link level simulations model the low level details of the transmitter and receiver. The physical layer algorithms used by the UE and BTS are modeled. These include channel coding, interleaving and error detection. Individual bits are mapped onto modulation symbols before being filtered and transferred across specific propagation channels. Receiver modeling is likely to include synchronization, channel estimation and equalization. Bit Error Rates (BER) and Block Error Rates (BLER) are calculated as a function of throughput and signal to noise ratio.
The general principle for Monte Carlo static simulations is presented in Fig
Figure 4
Each simulation snap shot is started by distributing a population of LTE across the simulation area. This distribution could be based upon a uniform random distribution or a weighted random distribution. Weightings can be based upon Erlang maps generated from the traffic belonging to an existing network. Alternatively, weightings could be environment type dependant so for example, urban areas could be specified to have a higher traffic density than suburban areas Once the population of LTE has been distributed, the simulation results are generated for that snapshot. The planning tool determines uplink and downlink signal to noise ratios for each physical channel and Reference Signal. Throughputs are derived using look-up tables which define the relationship between throughput and signal to noise ratio. These look-up tables typically originate from separate link level simulations. The results are recorded at the end of a simulation snapshot and the process is repeated. This allows the simulation to generate. Probability distributions and to quantify the probability of certain events occurring, e.g. the probability that a LIE will be able to establish a connection at a specific location. The number of snap shots necessary to
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 10
generate statistically stable simulation results tends to depend upon the quantity of traffic distributed during each snapshot. Distributing relatively little traffic tends to increase the. number of snap shots required The inputs to the planning tool for the simulation based approach to radio network planning are illustrated in Figure
Figure 5
The first three inputs are similar to those required by the path loss based approach. The LTE site data may be more complex in terms of requiring greater information to describe the BTS capability, e.g. baseband processing capability Propagation modeling is also more complex for a simulation if slow fading is modeled . The path loss based approach uses a link budget threshold which includes a slow fade margin. Simulations typically model slow fading explicitly making it necessary to specify a standard deviation and correlation factor. The correlation factor is used to specify the coherence of the fading experienced by the signals between a LIE and the set of surrounding BTS. A high correlation factor means that when one signal is experiencing a fade there is a high probability that the other signals will also be experiencing a fade Typical LTE parameter assumptions include channel bandwidth, maximum uplink and downlink transmit powers, Reference Signal transmit powers, uplink and downlink noise figures, look-up tables between signal to noise ratio and throughput for each propagation channel and throughput requirements for a range of services
Traffic profiles are specified in terms of the services used by the population of UE. Defining accurate traffic profiles can be difficult and it is reasonable to start a simulation exercise by modeling one service at a time, e.g, generate coverage and capacity results for the data service. Mid then generate similar results for the also .requires the geographic distribution of the UE to be defined. The main benefit of completing simulations is relative large quantity of information which is generated. This information can help guide planning decisions as well as provide more extensive expectation of network performance
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 11
2 LINK BUDGET
Link. Budgets are used during both system dimensioning and radio network planning.
The dimensioning process provides an estimate. Of the number of network elements required to achieve a specific coverage and capacity performance. Link budgets an: used during dimensioning to estimate the maximum allowed path loss and the corresponding cell range The results from a dimensioning exercise can be used as an input for a business case analysis. The number of network elements and their associated Configuration allows the cost of the network to be quantified. The path loss based approach to radio network planning makes lise of link budget results to define maximum allowed path loss thresholds
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 12
The channel Bandwidth is not used explicitly within the link budget but it has an impact upon the Signal to Interference plus Noise Ratio (SINR) requirement. SINR requirements are reduced for larger channel bandwidths when frequency domain scheduling is channel aware. Larger channel bandwidths provide the packet scheduler with greater flexibility to allocate Resource Blocks experiencing good channel conditions. The channel bandwidth also places an upper limit upon the number of Resource Blocks which can be allocated to the UE The total number of Resource Blocks is included for information and is not used explicitly within the link budget
The number of allocated Resource Blocks defines a trade-off between the cell capacity
and the cell range. Allocating a small number of Resource Blocks to the connection leads to less air-interface redundancy (higher coding rate and less benefit from channel coding). This means the cell range must be limited otherwise the eNode B will not be able to successfully decode the transport blocks. The benefit of allocating a small number of
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 13
Resource Blocks is that more Resource Blocks are available for other connections and the cell capacity is typically increased The example presented in Table allocates 8 Resource Blocks for a 500 kbps connection. Based upon Table3, a connection with 8 Resource Blocks can use a transport block size of 552 bits to achieve 500 kbps. Table 2 indicates that QPSK is used as a modulation scheme, which is appropriate for cell edge connections
Table 3
The set of 8 Resource Blocks is a relatively large allocation for a transport block size of 552 bits. A single Resource Block allocation with the normal cyclic prefix can accommodate 2 * 72 = 144 modulation symbols after accounting for the uplink Demodulation Reference Signal and the pairing of Resource Blocks in the time domain. This corresponds to a total allocated capacity of 2304 bits after accounting for all 8 Resource Blocks and the QPSK modulation scheme. The coding rate is then defined by the ratio of 552 / 2304 = 0.24. This represents a low coding rate so the corresponding SINR requirement should be relatively small and the maximum allowed path loss should be relatively large The example presented in Table 4 allocates 27 Resource Blocks for a 1 Mbps connection. Based upon figure8 , a connection with 27 Resource Blocks can use a
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 14
transport block size of 1192 bits to achieve 1 Mbps. Table 2 indicates that QPSK is used as a modulation scheme. The corresponding coding rate can be calculated as 1192 / 7776 = 0.15
Table 4
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 15
Table 5
The example presented in Table 5 allocates 25 Resource Blocks for a 2 Mbps connection. Based upon Table 3, a connection with 25 Resource Blocks can use a transport block size of 2216 bits to achieve 2 Mbps. Table 2 indicates that QPSK is used as a modulation scheme. The corresponding coding rate can be calculated as 2216 / 7200 = 0.31 The number of allocated subcarriers is given by 12 * the number of allocated Resource Blocks. The number of allocated subcarriers is used when aggregating the total thermal noise received by the BTS, i.e. it defines the noise bandwidth The maximum transmit power of 23 dBm corresponds to the capability of UE power class 3 specified by 3GPP within TS 36.101. This capability has a tolerance of +- 2 dB so 23 dBm could be optimistic for some devices. The maximum transmit power has been reduced to 22 dBm for the 1 Mbps and 2 Mbps examples because 3GPP TS 36.101 specifies a 1 dB Maximum Power Reduction (MPR) when more than 18 Resource Blocks are allocated from the 20 MHz channel bandwidth while using QPSK The terminal antenna gain can vary from one UE model to another. Data cards may have a higher antenna gain than handheld devices. UE typically have an antenna gain in the order of 0 dBi
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 16
Body loss is dependent upon the relative positions of the UE, the end-user and the serving cell. A figure of 3 dB is typically assumed when the UE is held to one side of the end-users head. A figure of 0 dB is typically assumed when the UE is positioned away from the body The first main result from the uplink link budget is the transmit Effective Isotropic Radiated Power (EIRP). This is defined using the expression below: Transmit EIRP = Maximum Transmit Power + UE Antenna Gain Body Loss The thermal noise per subcarrier quantifies the noise power within the bandwidth of a single 15 kHz subcarrier. This is calculated using 10 * LOG(kTB), where k is the Boltzmann constant (1.38 * 10-23), T is the temperature (290 Kelvin) and B is the bandwidth (15000 Hz) The aggregate thermal noise quantifies the noise power within the total allocated bandwidth. It is given by the thermal noise per subcarrier + 10 * LOG(number of allocated subcarriers) The receiver noise figure assumption reflects the performance of the eNode B receiver subsystem. The noise figure belonging to the eNode B cabinet should be used if the receiver subsystem does not include a Mast Head Amplifier (MHA). If an MHA is included, the noise figure should be the composite noise figure of the MHA, cable/connectors and eNode B cabinet. The composite noise figure can be calculated using Friis equation:
With the exception of the composite noise figure result, all of the variables within the preceding equation have linear units. The noise figure of the cable and connectors is equal to their loss. For example, the noise figure is 2 dB in log units and 1.6 in linear units if the cable and connector loss is 2 dB. The gain of the cable and connectors is equal to their loss, i.e. -2 dB in log units and 0.6 in linear units. Friis equation illustrates that when the MHA has a high gain, the noise figure of the receiver sub-system is dominated by the noise figure of the MHA. This emphasizes the importance of having a low noise, high gain amplifier for the MHA The interference margin is generated by co-channel interference from UE served by neighboring cells. The interference margin is likely to be greater in urban areas where the site density is relatively high. Heterogeneous network architectures can also lead to increased co-channel interference. Inter-Cell Interference Coordination (ICIC) is intended to help manage levels of co-channel interference The interference floor is defined using the expression below:
Interference Floor = Aggregate Thermal Noise + Receiver Noise Figure + Interference Margin
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 17
The Signal to Interference plus Noise Ratio (SINR) requirement is defined by link level simulations which model the BTS receiver performance when the allocated transport block size is transferred using the allocated number of Resource Blocks with a specific Block Error Rate (BLER). Link level simulations model a specific propagation channel so the SINR requirement is specific for that channel. Propagation channel modeling includes fast fading (unless it is a static channel) so the resultant SINR includes the impact of fast fading The SINR examples in Table 1 do not demonstrate an obvious trend between SINR requirement and bit rate requirement, i.e. the 500 kbps example has a higher SINR requirement than the 1 Mbps example, but a lower SINR requirement than the 2 Mbps example. This results from the different Resource Block allocations and different coding rates. The SINR requirement increases as the coding rate increases The second main result from the uplink link budget is the Received Signal Strength Requirement. This is defined using the expression below: Received Signal Strength Requirement = Interference Floor + SINR Requirement As expected, the Received Signal Strength Requirement increases as the bit rate requirement increases. The higher interference floors associated with the larger Resource Block allocations increase the resultant Received Signal Strength Requirement The eNode B antenna gain should be representative of the antenna type planned for network deployment. In practice, networks may include a range of antenna types. Antenna gains tend to decrease as the horizontal and vertical beam widths increase and the antenna becomes less directional
The antenna gain figure can incorporate a polarisation loss of approximately 0.5 dB. Antenna gains are typically quoted from measurements which have been recorded using a receiving antenna element which has exactly the same polarisation as the transmitting antenna element. In practice, the two antenna elements have different polarizations and a polarisation loss is experienced. Reflections change the polarization of a radio signal and this helps to reduce the loss because many signals with different polarizations can reach the receiving antenna. Cross polar antennas also reduce the potential for polarisation loss because the maximum angular offset is compared 45 to 90for a vertically polarized antenna The cable loss variable within the uplink link budget is only applicable if it has not already been included as part of the receiver noise figure. The uplink cable loss is included within the composite noise figure if an MHA has been assumed. Otherwise, the cable loss should equal all cable and connector losses between the eNode B cabinet and antenna. The example presented in Table 1 assumes an MHA is used so the cable loss is set to 0 dB The slow fading margin is calculated from an indoor location probability and an indoor standard deviation. The indoor location probability is often specified as an average probability of experiencing indoor coverage across the cell area. This figure is translated
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 18
to an equivalent cell edge indoor coverage probability before combining with the standard deviation to generate the slow fading margin. The indoor location probability at cell edge will be less than the average as a result of the higher UE transmit power requirement. The indoor standard deviation represents a combination of the outdoor standard deviation associated with slow fading, and the standard deviation generated by the variance of the building penetration loss The shadowing handover gain is generated by allowing the UE to handover onto the best server. When the UE is at cell edge and there are multiple potential serving cells, the UE is able select the best cell to help avoid experiencing fades. The shadowing handover gain is reduced when handovers have hysteresis to avoid ping-pongs between cells. The shadowing handover gain would reduce to 0 dB at the edge of network coverage where there are no neighboring cells to act as handover candidates. This may also be the case at some indoor locations Including the building penetration loss as part of the link budget generates an outdoor maximum allowed path loss result which includes sufficient margin to allow UE at the cell edge to establish and maintain connections from within buildings. The building penetration loss may be replaced by a vehicle penetration loss if link budgets are generated for a section of motorway or a rural area
The assumptions for building penetration loss typically depend upon the environment type, e.g. building penetration could be greater within an urban environment than within a suburban environment. The building penetration loss usually represents the link budget assumption with the greatest uncertainty. SINR figures and shadowing handover gains could have an uncertainty of (+-1) dB while building penetration loss could have an uncertainty of (+-5) dB. This uncertainty is included within the link budget result by calculating the slow fading margin from an indoor standard deviation which incorporates the variance of the building penetration loss. Building penetration loss assumptions are relatively difficult to validate in the field due to the large variance between different buildings and the geometry of those buildings with respect to the radio network plan The third main result from the uplink link budget is the Isotropic Power Requirement. This is defined using the expression below: Isotropic Power Requirement = Received Signal Requirement eNode B antenna Gain + Cable Loss + Slow Fading Margin Shadowing Handover Gain + Building Penetration Loss The Maximum Allowed Path Loss is then calculated as the difference between the transmit EIRP and the isotropic power requirement: Maximum Allowed Path Loss = Transmit EIRP Isotropic Power Requirement This maximum allowed path loss result can be compared with the equivalent downlink result to determine whether coverage is uplink or downlink limited. This comparison requires an offset to account for the frequency difference between the uplink and downlink frequency bands. Higher frequencies tend to experience greater path loss so coverage will tend to be downlink limited if both the uplink and downlink link budgets
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 19
generate equal maximum allowed path loss results. The frequency dependant term within a typical Okumura-Hata path loss model is given by the equation below: Frequency Depended loss= 33.9*LOG(Frequency(MHz)) The equation indicate for the fixed cell range .
The channel Bandwidth is not used explicitly within the link budget but it has an impact upon the Signal to Interference plus Noise Ratio (SINR) requirement. SINR requirements are reduced for larger channel bandwidths when frequency domain scheduling is 'channel aware. The channel bandwidth 'also places an upper limit upon the number of Resource Blocks which can be allocated to the UE The total number of Resource Blocks is used When calculating the transmit power for the allocated Resource Blocks, i.e. the maximum transmit power is distributed across the total number of Resource Blocks so only a proportion of that power is available for the allocated Resource Blocks.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 20
The number of allocated Resource Blocks defines a trade-off between the cell capacity and the cell range. Allocating a small number of Resource Blocks to the connection leads to less air-interface redundancy (higher coding rate and less benefit from channel coding). This means the cell range must be limited otherwise the UE will not be able to successfully decode the transport blocks. The benefit of allocating a small number of Resource Blocks is that more Resource Blocks are available for other connections and the cell capacity is typically increased The number of allocated Resource Blocks in Table 6 have been kept similar to those in Table2 to allow a comparison between uplink and downlink An allocation of 8 Resource Blocks has been assumed for the 500 kbps connection. Similar to the uplink, a transport block size of 552 bits can be used with QPSK as a modulation scheme. 2x2 MIMO is assumed for the link budgets in Table 3 but single layer .transmission with a single codeword (single transport block) is assumed at cell edge The set of 8 Resource Blocks is a relatively large allocation for a transport block size of 552 bits, Assuming that the PCFICH.PHICH and PDCCH occupy the first 2 OFDMA symbols within the sub frame and that 2x2 MIMO is used (impacts the number of Resource Elements allocated to the cell specific Reference Signal ) then the number of Resource Elements remaining for the PDSCH is given by 8 x [(12 x 7 x 2) - (12 x 2 +(2)] = 1056. this corresponds to a capacity of 2112 bits when using QPSK. The coding rate is then defined by-the ratio 01'5521 2112bits=O.26. The example presented in Table 6 allocates 26 resource Blocks for a I Mbps connection. based upon Table 3, a connection with . 26 Resource Blocks can use a transport block size. of 1160 bits to achieve 1 Mbps. Table 2 indicates that QPSK is used as a , modulation scheme. The corresponding coding rate can be calculated as 1.160/6864 = 0.17. The example presented in Table 6 allocates 25 Resource Blocks for a2 Mbps connection. Based upon Table 3,a connection with 25Resource I310cks can use a transport block size of 2216 bits to achieve 2 Mbps. Table 2 indicates that QPSK is used as a modulation scheme. The corresponding coding rate can be calculated as 2216/ 6600 = 0.34.
The number of allocated subcarriers is given by 12 x the number of allocated Resource Blocks. The number of allocated subcarriers is used when aggregating the total thermal noise received by the UE i.e. it defines the noise bandwidth The maximum transmit power of 43dBm corresponds to a typical rnacrocell downlink transmit power capability The downlink transmit power is distributed across the entire channel bandwidth so only a percentage of the total power is available for the Resource blocks allocated to the connection being considered in the link budget. In the case of the 500 kbps connection, 8 out of 100 Resource Blocks have been allocated so the downlink transmit power for the
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 21
connection is 43 - 10 x LOG( I00/8) = 32.0dBm. Likewise. the transmit powers available for the 1 Mbps and2 Mbps connections are 37.1 dBmand37.0dBm respectively The link budgets presented in Table 344assume the use of 2x2 MIMO so there are 2 transmitting antenna ports and the downlink transmit powers across the air-interface are increased by3 dB The eNodB antenna gain should be representative of the antenna type planned for network deployment. In practice, networks may include a range of antenna types. Antenna gains tend to decrease as the horizontal and vertical beam widths increase and the antenna becomes less directional The cable loss depends upon the site design and the use of remote radio heads or active antenna systems. assumes a conventional site design with 2dB of cable loss in the downlink direction This cable loss includes the MHA insertion loss when an MHA is present The first main result from the downlink link budget is the transmit EIRP which is defined as: Transmit ElRP = Transmit Power for Allocated Recourse Blocks +Multiple Antenna Increase + Antenna Gain - Cable Loss
The thermal noise per subcarrier quantifies the noise power within the band width of a single 15 kHz subcarrier, This is calculated using 10x LOG(kTB), where k is the Boltzmann constant(1.38 x l 0-23) , T is the temperature (290 Kelvin) and B is the bandwidth(1500 Hz) The aggregate thermal noise quantifies the noise power within the total allocated bandwidth. It is given by the thermal noise per subcarrier + 10x LOG(number of allocated subcarriers The receiver noise figure assumption reflects the performance of the. UE receiver and is likely to vary between UE models. A noise figure of 7 dl3 represents a typical assumption. The interference margin is generated by co-channel interference from neighboring eNode B. The interference margin is likely to be greater in urban areas where the site density is relatively high. Heterogeneous network architectures can also lead to increased co channel interference. Inter-Cell Interference Coordination (IClC) is intended to help manage levels of co-channel interference The interference floor is defined using the expression below: Interference Floor = Aggregate Thermal Noise + Receiver Noise Figure + Interference Margin The Signal to Interference plus Noise Ratio (SINR) requirement is defined by link level simulations which model the UE receiver performance when the allocated transport block size is transferred using the allocated number of Resource Blocks with a specific Block Error Rate (BLER). Link level simulations model a specific propagation channel so the
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 22
SINR requirement is specific for that channel. Propagation channel modeling includes fast fading (unless it is a static channel) so the resultant SINR includes the impact of fast fading The SINR examples in Table2 show the same trend as for the uplink, i.e. the 500 kbps example has a higher SINR requirement than the I Mbps example, but a lower SINR requirement than the 2 Mbps example. This results from the different Resource Block allocations and different coding rates. The S[NR requirement increases as the coding rate increases The second main result from the downlink link budget is the Received Signal Strength Requirement. This is defined as: Received Signal Strength Requirement = interference Floor + SINR Requirement As expected.jhe Received Signal Strength Requirement increases as the bit rate requirement increases, The higher interference floors 'associated with the larger Resource Block-allocations increase the resultant Received Signal Strength Requirement The UE antenna gain, body loss, slow fading margin, shadowing handover gain and building penetration .loss assumptions arc the same as: those for the uplink link budget The third main result from the from the Downlink budget is the isotropic power Requirement. This define as : Isotropic power Requirement = Received signal Requirement UE antenna gain + Body Loss + slow fading margin - Shadowing Handover Gain + building penetration loss Maximum Allowable path Loss is given by : MAPL = Transmit EIRP- Isotropic Power Requirement
Two Examples are there for link budget calculation in the uplink & downlink.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 23
Determine the System Gain for QPSK1/2, 16QAM3/4 and 64QAM4/5 in the downlink
direction and for QPSK1/2 and 16QAM3/4 in the uplink. Assume worst case for resource block allocations i.e 25.
Table 7
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 24
Table 8
Maximum Path loss:The LTE system is to be deployed in a dense urban area, with an area reliability of 95%. Some in-building coverage is expected and preliminary investigation suggests that single wall penetration losses in this frequency band should be approximately 10dB. There is no significant vegetation in the area where deployment is to begin. The user equipment is initially based on USB dongles therefore body losses will be kept to a minimum. Whilst interference from neighboring cells is not expected to be at network launch an interference margin of 5dB should be included in the preliminary design. Given the above description determine the MAPL of the system. (Use the system gain figures from the first part of this exercise)
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 25
Table 9
Determining Cell Radius: Assuming the COST-231 Propagation Model for an urban area what are uplink and downlink ranges for the system above. The eNB antennas will be at 25m and UE antenna height is assumed to be approximately 1.5m.
Table 10
SS2 RSRQ.xlsx
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 26
For PDSCH and PUSCH. For L1/L2 control and common channels other coding schemes can be used. Downlink Only static Reference Signal power boosting has been specied by 3GPP, vendor-specic implementations possible. With UE-specic reference signals (vendor-specic beam forming) arbitrary number of Tx antennas. For simultaneous transmission. Transmit antenna selection is possible with RF switching. Multiuser MIMO possible in UL in 3GPP Release 8. Intra-TTI and inter-TTI frequency hopping is possible in UL.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 27
Higher the MCS used, higher the required SINR and vice versa. This means that using QPSK will have a lower required SINR than 16-QAM . Required SINR can be estimated by two different methods. By using the Throughput vs. average SNR tables. These tables are obtained as an output of link level simulations. For each type of propagation channel models and different antenna configurations, different tables are needed. One important thing to note here is that noise is modeled as AWGN noise; therefore, SNR is used instead of SINR. By using the Alpha-Shannon formula. Alpha-Shannon formula provides an approximation of the link level results. Thus, in this case, no actual simulations are needed, but factors used in Alpha-Shannon formula are needed for different scenarios.
5.2.1 Spectral Efficiency: In case the cell edge is defined by the input required throughput, the corresponding
spectral efficiency has to be derived. The spectral efficiency is derived under the following assumptions:
The layer 2 protocol overhead (MAC and RLC) is negligible [23] Link level simulation do not take into account the L1 overhead due to control
channels (pilot and allocation table) Given the required cell throughput at cell border Cell Edge Throughput, the L1 throughput is calculated as follows Layer Throughput = Cell Edge throughput /overhead factor Where Over head Factor = Data Symbol per sub Frame /Total symbol per sub Frame The Overhead Factor values for DL and UL are respectively 5/7 and 4/7 , assuming short cyclic prefix. Thus, the spectral efficiency is: Spectral Efficiency= Layer 1 Throughput /Cell Band width
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 28
Spectral efficiency is then used to find out the Required SINR using Alpha-Shannon formula. Shannon capacity formula for maximum channel efficiency as a function of SNR can be written as:
This maximum capacity cannot be obtained in LTE due to the following factors Limited coding block length Frequency selective fading across the transmission bandwidth Non-avoidable system overhead Implementation margins ( channel estimation, CQI)
Thus, in order to fit the Shannon formula to LTE link performance two elements are introduced
Note that also depends on the antenna configuration. The formula is valid between the
limits specified by a minimum and a maximum value of spectral efficiency. The figure below shows how the Shannon-Alpha formula is used to approximate the envelope of the spectral efficiency vs. SNR curve in case of SISO (1 transmission and 1 reception antenna) and AWGN. Two values of and Imp Factor are considered.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 29
Figure 6
Figure1 --LTE spectral efficiency as function of G-factor (in dB) including curves for best Shannon fit
To map these results to system level performance, we need to consider the G-factor
distribution, PDF(G), over the cell area. Assuming uniform user distribution, the obtained G-factors for the LTE capacity evaluation are plotted in Figure1. The distributions are obtained by deploying Macro Cell and Micro Cell hexagonal cellular layouts according to . The probability density function of G is obtained from Figure 2. It is assumed that all users have equal session times (e.g. infinite buffer assumption)
Figure 7
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 30
5.3 INTERFERENCE
In order to evaluate the other-cell interference, a simple network model in which the load
is equally distributed among cells is assumed. The overall effect of interference can be estimated the following factors
A term that takes into account the loss in G due to the handover margin (CellOverlapMargin). The G-factor distribution is defined as the average own cell power to the other-cell power plus noise ratio. In fact, a handover margin is needed for avoiding ping-pong effect. As a consequence, the serving cell is not necessary the one that is received with the strongest signal. A gain due to interference control mechanisms (e.g. Soft Frequency Reuse or Smart Frequency Domain Packet Scheduler), denominated IntControlGain.
For the uplink, the issue of interference is dealt as follows. The uplink other cell
interference margin (OtherCellInterferenceUL in the maximum uplink path loss equation) was studied by means of system level simulations, using a network scenario with 19 three-sector sites, i.e., in total 57 cells. The sites were positioned on a regular hexagonal grid. Inter-site distanced of 1732 m with penetration loss of 20 dB and UE power class of 21 dBm was used. Interference coordination was not used in this simulation. Simulations were carried out with three different values of system load. Allocated bandwidth per user equals to 312.5 kHz. Slow power control was used in this simulation. Target for power control was set in such a way that it provides a good tradeoff between the cell edge throughput and average cell throughput The interference margin was calculated using the following expression Interference margin = SNR/SINR Figure shows the obtained interference margin as a function of load. The interference margin is observed from 5% point of CDF. The table instead, shows the list of Interference Margin Values obtained using linear interpolation.
Table 11
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 31
Table 12
Figure 8
Three different types of sites (Omni-directional, bi-sector, tri-sector) For three hexagonal cell models, site areas can be calculated as follows. o Omni-directional site` Site Area = 2.6 * CellRadius^2 o Bi sector Site Site Area = 1.3*2.6* cell radius^2 o Tri sector Site Site Area = 1.95*2.6*Cell Radius^2 The number of sites to be deployed can be easily calculated from the Cell Area and the input value of the deployment area (Deployment Area). Number of Sites coverage = Deployment Area/Site Area
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 32
Table 13
BS PA Output (dBm) 35 Modulation Scheme QPSK 1/2 Rate 16-QAM 3/4 Rate 64-QAM 4/5 Rate Ant gain (dBi) 13 Bit Rate (Mbps) 3.6 10.7 17.1 BS EIRP (dBm) 48 Rx Sens. (dBm) -96.5 -85.3 -78.4 Oper Freq (MHz) Area Type 2600 Dense Urban COST 231 HATA Ant gain (dBi) Additional Losses (dB) 0 Penetration loss Fade Margin 10 10
Modulation Scheme QPSK 1/2 Rate 16-QAM 3/4 Rate 64-QAM 4/5 Rate
% of Area Average Capacity 76.88% 5.8 Mbps 13.74% 13.3 Mbps 9.38% 17.1 Mbps
FALSE
MAPL QPSK Freqency BS Height Mobile height Dense Urban Urban Suburban Rural
-1.82088774
Distance
0.27 Km 0.37 Km 0.71 Km 1.90 Km
MAPL 16 QAM Freqency BS Height Mobile height Dense Urban Urban Suburban Rural
-1.82088774
Distance
0.13 Km 0.18 Km 0.34 Km 0.92 Km
MAPL 64 QAM Freqency BS Height Mobile height Dense Urban Urban Suburban Rural
-1.82088774
Distance
0.08 Km 0.11 Km 0.22 Km 0.58 Km QPSK 0.27 Km 0.37 Km 0.71 Km 1.90 Km 16 QAM 0.13 Km 0.18 Km 0.34 Km 0.92 Km 64 QAM 0.08 Km 0.11 Km 0.22 Km 0.58 Km
This is the example for the Coverage & capacity Calculation for 2600Mhz Freq. for different area.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 33
6 CAPACITY PLANNING
Capacity planning gives an estimate of the resources needed for supporting a specified
offered traffic with a certain level of QoS (e.g. throughput or blocking probability). Theoretical capacity of the network is limited by the number of eNodeBs installed in the network. Cell capacity in LTE is impacted by several factors, which includes interference level, packet scheduler implementation and supported modulation and coding schemes. Link Budget (Coverage Planning) gives the maximum allowed path loss and the maximum range of the cell, whereas coverage Planning takes into account the interference by
Providing a suitable model. LTE also exhibits soft capacity like its predecessor 3G
systems. Therefore, the increase in interference and noise by increasing the number of users will decrease the cell coverage forcing the cell radius to become smaller.
In LTE, the main indicator of capacity is SINR distribution in the cell. In this study, for the
sake of simplicity, LTE access network is assumed to be limited in coverage by UL direction and capacity by DL.
The evaluation of capacity needs the following two tasks to be completed Being able to estimate the cell throughput corresponding to the settings
used to derive the cell radius Analyzing the traffic inputs provided by the operator to derive the traffic demand, which include the amount of subscribers, the traffic mix and data about the geographical spread of subscribers in the deployment are
6.1
The target of capacity planning exercise is to get an estimate of the site count based on
The most accurate evaluation of cell capacity (throughput under certain constraints) is
given by running simulations. Since, the dimensioning is usually done using an excel workbook, the best solution to derive cell throughput is direct mapping of SINR distribution obtained from a simulator into MCS (thus, bit rate) or directly into throughput using appropriate link level results. .
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 34
Average SINR distribution table (system level result), which provides the SINR probability Average throughput or spectral efficiency versus average SINR table (link level result)
Subsequently, MCS supported by each value of SINR is selected by using the minimum
allowed SINR from the link level results. This gives the corresponding data rate that is supported by that MCS. In this way, data rate corresponding to each SINR value is obtained for a specific scenario. For urban channel model and a fixed inter-site distance of 1732m, downlink throughput for LTE is shown in table
Table 14
Let us consider an example regarding table 5-1 (Urban/1732m inter-site distance). For an
SINR value of 2dB, QPSK is selected from the above table, and it gives a throughput of 6Mbps at 2dB. In the same way, an SINR value of 3dB corresponds to 6Mbps, 4dB to 8Mbps and 7dB to 12Mbps in DL. Once all the values are calculated by using the lookup table, cell throughput is derived as follows:
Where,SINR _Occurrence _probability = Probability of occurrence of a specific SINR value at cell edge obtained using simulations
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 35
6.2 SENSITIVITY
Sensitivity depend upon number of resource block if number of resource block are increases sensitivity decrease
Table 15
nRB 1 kT -174 -174 -174 -174 -174 -174 -174 -174 -174 -174 -174 -174 MCS SNR Sens QPSK 1/3 -1 -116.9 QPSK 1/2 2 -113.9 QPSK 2/3 4.3 -111.6 QPSK 3/4 5.5 -110.4 QPSK 4/5 6.2 -109.7 16QAM 1/2 7.9 -107.5 16QAM 2/3 11.3 -104.1 16QAM 3/4 12.2 -103.2 16QAM 4/5 12.8 -102.6 64QAM 2/3 15.3 -99.1 64QAM 3/4 17.5 -96.9 64QAM 4/5 18.6 -95.8 nRB nRB 12 25 Sens Sens -106.2 -103.0 Reference -103.2 -100.0 -100.9 -97.7 -99.7 -96.5 -99.0 -95.8 -96.8 -93.6 -93.4 -90.2 -92.5 -89.3 -91.9 -88.7 -100.0 -88.4 -85.2 -86.2 -83.0 -105.0 -85.1 -81.9
Sensitivity
-110.0
k*T -174
NF 6
IM 2.5 3 4
Gdiv -3
-115.0 -120.0
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 36
7.1 Reference Signal Received Power (RSRP): Reference signal received power (RSRP) identifies the signal level of the Reference Signal. It is defined as the linear average over the power contributions of the resource elements that carry cell-specific reference signals within the considered measurement frequency bandwidth. Design KPI for RSRP: 10MHz Channel Bandwidth (700MHz & AWS): -98 dBm /-103 dBm 5MHz Channel Bandwidth (700MHz & AWS): -98 dBm /-103 dBm A minimum of 95% of the weighted average of the LTE design service area (Cluster or Polygon) must meet the RSRP targets specified above. The criterion of 95% is based on a weighting using the same clutter weights used for traffic spreading. The target specified above is after taking into consideration the indoor loss values assigned per clutter type (In-building losses enabled). Note: The targets for AWS are only applicable in cases where the AWS design is being carried out as a standalone design and not be used as a capacity layer over an existing 700 MHz layer LTE network.
7.2
Reference Signal Received Quality (RSRQ) identifies the quality of the Reference Signal. It is defined as the ratio NRSRP/(E-UTRA carrier RSSI), where N is the number of RB"s of the EUTRA carrier RSSI measurement bandwidth. The measurements in the numerator and denominator shall be made over the same set of resource blocks. E-UTRA Carrier Received Signal Strength Indicator (RSSI), comprises the linear average of the total received power observed only in OFDM symbols containing reference symbols for antenna port 0, in the measurement bandwidth, over N number of resource blocks by the UE from all
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 37
sources, including co channel serving and non-serving cells ,adjacent channel interference, thermal noise etc. Design KPI for RSRQ: 2 Transmit Paths: 50% Load: -15 dB 100% Load: - 18 dB A minimum of 95% of the weighted average of the LTE design service area (Cluster or Polygon) must meet the RSRQ targets specified above. The criterion of 95% is based on a weighting using the same clutter weights used for traffic spreading.
Power per RE (w) 0 0 0 0 0 0.083 0 0 0 0 0 0.083
RSRQ CRITERIA FOR 0 % LOAD RSRQ calculation is done for a single RB using the entered value for
power, no pathloss is used since the values are relative to each other and PL (or TxPwr in fact) will not affect this simple calculator
Load % 0%
Power (w) 1
External Interference 0 #RB 25 #SC 300 Power/Carrier (w) Power/SC (w) Power/RS (w) 1 0.0033 0.0033 30.0 dBm 5.2 dBm 5.2 dBm # non RS SC 250 RSSI and RSRP Measured only in symbols containing RS Pathloss (dB) 130 RSSI (w) 1 RSSI (dBm) -100.0 RSRP (w) 0.0033 RSRP (dBm) -124.8 RSSI - RSRP Offset -24.8 dB
this will be the power difference between RSSI and channel BW (RB)
# RS SC 50
Figure 9
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 38
RSRQ calculation is done for a single RB using the entered value for power, no pathloss is used since the values are relative to each other and PL (or TxPwr in fact) will not affect this simple calculator
Load % 30%
Power (w) 1
External Interference 0 #RB 25 #SC 300 Power/Carrier (w) Power/SC (w) Power/RS (w) 1 0.0033 0.0033 30.0 dBm 5.2 dBm 5.2 dBm # non RS SC 250 RSSI and RSRP Measured only in symbols containing RS Pathloss (dB) 130 RSSI (w) 1 RSSI (dBm) -100.0 RSRP (w) 0.0033 RSRP (dBm) -124.8 RSSI - RSRP Offset -24.8 dB # RS SC 50
Figure 10
Load % 60%
Power (w) 1
External Interference 0 #RB 25 #SC 300 Power/Carrier (w) Power/SC (w) Power/RS (w) 1 0.0033 0.0033 30.0 dBm 5.2 dBm 5.2 dBm # non RS SC 250 RSSI and RSRP Measured only in symbols containing RS Pathloss (dB) 130 RSSI (w) 1 RSSI (dBm) -100.0 RSRP (w) 0.0033 RSRP (dBm) -124.8 RSSI - RSRP Offset -24.8 dB # RS SC 50
Figure 11
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 39
Power per RE (w) 0.083 0.083 0.083 0.083 0 0.083 0.083 0.083 0.083 0.083 0 0.083
RSRQ calculation is done for a single RB using the entered value for power, no pathloss is used since the values are relative to each other and PL (or TxPwr in fact) will not affect this simple calculator
Load % 80%
Power (w) 1
External Interference 0 #RB 25 #SC 300 Power/Carrier (w) Power/SC (w) Power/RS (w) 1 0.0033 0.0033 30.0 dBm 5.2 dBm 5.2 dBm # non RS SC 250 RSSI and RSRP Measured only in symbols containing RS Pathloss (dB) 130 RSSI (w) 1 RSSI (dBm) -100.0 RSRP (w) 0.0033 RSRP (dBm) -124.8 RSSI - RSRP Offset -24.8 dB # RS SC 50
Figure 12
Load % 100%
Power (w) 1
External Interference 0 #RB 25 #SC 300 Power/Carrier (w) Power/SC (w) Power/RS (w) 1 0.0033 0.0033 30.0 dBm 5.2 dBm 5.2 dBm # non RS SC 250 RSSI and RSRP Measured only in symbols containing RS Pathloss (dB) 130 RSSI (w) 1 RSSI (dBm) -100.0 RSRP (w) 0.0033 RSRP (dBm) -124.8 RSSI - RSRP Offset -24.8 dB # RS SC 50
Figure 13
7.3 Overlapping Zones (Number of Servers):The overlapping zones (number of servers) criteria are used to establish the quality of the RF propagation environment from an interference point of view. The goal of the number of serverscriteria is to establish dominance and reduce the waste of network resources and degraded network performance that may occur when multiple servers exist in the same
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 40
geographic area. The calculation is based on the reference Signal (RS) signal levels of the servers.
Design KPI for Overlapping Zones (Number of Servers): Within 5 dB of the best server % area with 4 or more servers should be < 2%. % of area with 2 or more servers should be < 30%. Within 10dB of the best server % of area with 7 or more servers should be < 2%. The calculation is based on area importance. The clutter weights used for traffic spreading establishes the importance of the geographic area. The idea here is to focus the LTE design where LTE users are located (for example, core urban areas, convention centers, major stadiums, etc.) instead of areas within the LTE polygon with no users (for example, scrublands, forests, etc.)
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 41
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 42
Figure 14
Figure 14: Under the 3GPP model, the cell-edge SINR values rarely go below SINR = 8 dB
There are several obvious limitations which make the 3GPP model ill-suited to estimate cell-edge performance. The model is too idealistic; it is difficult at best to find a real-life
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 43
cellular network that contains only 19 eNodeBs with identical cell radii, identical antennas, identical tower heights and uniform user distribution. The effect of using this idealistic model is that the measured cell-edge SINR values from a large-scale real-life network (Figure 2) can be much worse than the SINR generated from simulation (Figure 1); in other words, the model is likely to underestimate these values.
Figure 15
Figure 15: SINR distribution of a real-life N=1 OFDMA network has a much longer tail reaching SINR = 12 dB Most trial networks only contain a few base stations; these few neighbor cells do not contribute sufficient out-of-cell interference even if they are all fully loaded. It is not costeffective to maintain a trial network of appropriate size merely to create sufficient out-ofcell interference to generate realistic cell-edge SINR distributions. Some people believe that the out-of-cell interference is not important if it originates from cells that are physically far away from the center cell. This is not always true; cells that are located far away can still cause significant interference if they have line-of-sight (LOS) condition (see Figure 3). The consequences of relying on results from simulation and trial networks is that, although performance can look very promising, cell-edge performance in an actual largescale deployment can be much worse than originally anticipated, especially under heavy traffic loads. This puts the responsibility for problem solving in the hands of the field engineers. Sometimes performance can be only brought up to acceptable levels through lengthy trial-and-error processes; other times performance cannot be corrected because the defects are in the current release of the standard. Once the industry realizes that the problems are valid, corrections are made in the next release of the standard. But it takes years for the next release of the standard to be implemented in the field. In the meantime, network performance can only be as good as the field engineers can make it. This kind of situation is a common occurrence, especially when a new system is deployed. For example, when the first system with universal frequency reuse (N=1) was deployed, no one realized how bad the out-of-cell interference could be when the load became heavy. The measured SINR distributions from the field turned out to be much worse than the SINR distributions obtained from simulations or from trial networks (a long tail toward the negative values with SINR < 12 to 15 dB). What are the causes of such low cell-edge SINR? Multiple factors are involved, but the main cause is irregularities from real-life cellular networks. These irregularities can
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 44
cause very negative SINR in some locations (although they can result in good SINR in other locations); the net result is a long tail in the SINR distribution. The situation is better for N>1 networks (such as GSM or AMPS) because in that case, the interferers(co-channels) are physically located farther apart from each other due to the frequency reuse distance. The situation is worst for N=1 networks since in that case, every cell is an interferer. Pilot pollution (or no dominant server) describes a situation where power transmitted from many different cells appears in a location, but none is significantly better than others. As a result, the composite signal level is high, but the SINR from any single cell is poor because the total interference is too high. The result is poor RF performance even with a high overall signal level. Figure 3 shows one common cause of the no dominant server problem. The cells located nearby have unfavorable RF propagation conditions; but the cells located far away have favorable RF propagation conditions. The net result is: many servers appear in a location but no server is offering a strong enough signal. Without soft handoff, the terminal can only treat received power from one cell as signal; power from all other cells is treated as interference. Thus, the no dominant server problem means high interference and poor SINR:
Where S = received signal level; n is the thermal noise energy which is a constant,
Is the total out-of-cell interference contributed from all neighbor cells The larger the value of I, the worse the SINR.
Figure 16
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 45
Figure 4 shows an indoor deployment. The upper floors of high-rise buildings have LOS, with many cells on the ground. The composite signal levels on the upper floors can be very high, but no server is much better than the others, so the combined SINR from every server is poor.
Figure 17
Figure 17: Pilot pollution of upper floors caused by cells on the ground
9.3 Effects Caused by Mobility: Vehicles moving at high speed may be subject to much worse cell-edge SINR due to a handover dragging effect. Essentially, this is caused by the fact that a fast-moving UE cannot always be served by the best server, because handover is not triggered until the UE has moved across the cell border, and there is a time lapse while handover completes. When a UE moves across the cell border, before handover completion, it is served by the original cell (serving cell), which now becomes the second- or third-best server. The UE will not be served by the best server until after the handover is successfully completed (Figure 18). The reason the serving cell cannot be the best server is due to the handover trigger condition (Event A3 as defined in [2]): The RSRP from a new candidate cell must be better than the RSRP of the current serving cell by a certain margin (=Hysteresis) in order for the handover trigger to happen. Therefore, at the handover trigger point, the serving cell is not the best server, but the candidate cell is. Also there is a time-to-trigger
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 46
after Event A3, so the faster the moving speed, the farther away the UE will go before it can be switched to the best server.
Figure 18
However, the UE must first have message exchanges to the current serving sell (which is not the best server), and handover can only be successful after these message exchanges are successful with the current serving cell (Figure 19). Handover message exchanges are defined in [3].
Figure 19
Figure 19: Handover message exchanges, first with the serving (source) cell, then with the candidate (target) cell
The common problem is that near the cell edge, the SINR from the best server is already
very poor, and the SINR values from the second- and third-best servers are even worse.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 47
Figure 7 shows the overlapping regions among the best, second-best third-best servers near the cell edges. 3GPP simulation only shows the SINR distribution from the best server. However, in real-life situations, the UE also has to work with the second- or thirdbest server, so the real-life situation is less favorable.
Figure 20
Figure 7: Overlapping areas of the best-, second-best and third-best servers near the cell edge Failure rates for message exchanges with the serving cell, under the worst-case scenario, can be high. Figure 8 shows the simulated cell-edge SINR values for different mobile speeds [4], [5]. One can see that the high-speed mobile may see cell-edge SINR values worse than 30 dB; no channel can operate with such poor SINR values.
Figure 21 Figure 21: SINR distributions of UE with low mobility (left) and high mobility (right)
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 48
Note that Figure 21 is based on simulations using the 3GPP model, which is very idealistic; every handoff has a well-defined cell border and unique target cell. In reality, these boundaries and targets are far from clear, especially in areas with no dominant server (Figure 22). There can be multiple cell borders and different target cells at different times, due to fast variation of SINR from each server (Figure 10). This SINR fluctuation is the reason a relatively large hysteresis is needed in the handover triggering condition, otherwise it will ping pong. However, the larger the value of the hysteresis, the worse the handover dragging effect will be, and the worse the cell-edge SINR from the serving cell.
This handover dragging effect is particularly severe for small cells with high-speed UEs,
which is a difficult situation for any cellular system. Some people argue that high-speed UEs should not be in urban areas with small cells, due to frequent red-light stops. This is not always true. In modern cities, highways can go through cities and cars can drive at high speeds without making stops; bullet trains can also pass through cities at high speeds, as shown in Figure 22.
Figure 22
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 49
Figure 23
Figure 23: Two phases of RLF as defined in TS 36.300, Section 10.1.6 What kind of SINR will result from a PDCCH BLER in excess of 10%? Vendors have performed simulations and the results are summarized in RAN-4 documents [8]-[14]. One can see from Figure 24, that the BLER of PDCCH reaches 10% when SINR values drop to between 3 dB and 5 dB.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 50
Figure 24
Figure 24: Comparison of PDCCH performance results from different vendors simulations Consider the best-case scenario, where SINR = 5 dB is needed to avoid RLF. How much area can contours of SINR = 5 dB cover for N=1 networks? Figure 14 shows the results from 3GPP-like modeling. One can see that even in such an idealistic network, under the best-case scenario SINR = 5 dB contours cannot reach the cell edge with 75% of cell-edge reliability.
Figure 25 Contours of SINR = 5 dB cannot cover to the cell edge with 75% of edge reliability
Figure 25: Coverage contours of SINR=5 dB under N=1 scenario One may wonder, if the contour of SINR = 5 dB cannot even reach the cell edge, how handover can ever be successful since it requires the PDCCH to perform beyond the cell edge?
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 51
The answer is, only under the true N=1 scenario (i.e., all subcarrier frequencies are used in all cells), contours of SINR = 5 dB cannot reach the cell edge. However, in most other cases, the interference scenario in PDCCH is not a true N=1. PDCCH has a way to mitigate co-channel interference from direct neighbors, as long as it is not fully loaded. It uses a scrambling mechanism in which the symbol quadruplets of the CCEs from each cell are shifted to different sub-carrier frequencies, or different symbols, to randomize and reduce the probability of collisions with direct neighbor cells, as shown in Figure 26. For details about PDCCH multiplexing and scrambling, please refer to [26]. The result is that the PDCCHs co-channel interference in most cases is closer to N=3 instead of N=1, as long as the loading on PDCCH is light so that most REs in the PDCCH control region are not occupied. On the other hand, if PDCCH from all cells are fully loaded, then the co-channel interference scenario will be in the region of N=1.
Figure 26
Figure 26: Interference scenarios for PDCCH Figure 16 shows the coverage of the contour SINR = 5 dB for N=3. Because for N=3, the direct neighbors do not cause co-channel interference, one can see that the contour of SINR = 5 dB can go much farther beyond the cell edge. This means that PDCCH will probably not have cell-edge performance issues, as long as the loading level on PDCCH is light so the out-of-cell interference scenario is more like that for N=3 instead of N=1.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 52
This leaves one important question: what will produce heavy load on the PDCCH? This depends on the type of data traffic; some traffic types tend to load traffic channels more than control channels; other types of data models will load control channels more than traffic channels. When the network is supporting a small number of high data-rate users (e.g., FTP, video streaming), it loads the traffic channels much more than the control channels. Because of the small number of users per cell, the control channel is lightly loaded. This is likely to be the case for initial LTE deployments.
The PDCCHs load will become heavy if there are a large number of low-rate users in the cell, such as the case for VoIP deployment. A large number of low-rate users tends to heavily load the PDCCH and lightly load the traffic channels. For VoIP, the overall capacity limit is due to the PDCCH capacity limit. This is the case even with semipersistent scheduling [16].
Figure 27
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 53
Cell-edge performance issues due to PDCCH will become worse after massive deployment of VoIP, which tends to heavily load the PDCCH. Figure 28 shows one simulation result of probability of PDCCH collision as a function of the loading level.
Figure 28
Figure 28: CCE collision probability increases with the PDCCH loading level
When PDCCH is fully loaded, scrambling can no longer avoid collisions with the
neighbor cells. As a result, the interference scenario will be more like N=1, the service area of SINR = 5 dB will shrink, and cell-edge performance will become worse.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 54
minimize co-channel interference with direct neighbors. Furthermore, LTE defines a few mechanisms to measure or notify direct neighbors of the out-of-cell interference levels on each RB (HII, OI, RNTP) [21]. Working in the power domain is also relatively easy, as fast power control is performed on the UL anyway. Also, the DL power level on selected RBs can be changed, for example, power boost for cell-edge users. Figure 18 shows two examples of traffic channel ICIC algorithms. The figure on the left shows an example for frequency-domain ICIC: frequency allocations for cell-edge users are restricted to about 1/3 of total channel bandwidth in order to avoid co-channel interference with direct neighbors; cell-center users can use the full bandwidth. The figure on the right shows an example of ICIC that works on both frequency domain and power domain: cell-edge users use one-third of the bandwidth but higher power; cell center users use full bandwidth but lower power.
Figure 29
Figure 29: Schematic diagram of various traffic channel ICIC solutions, showing ICIC in frequency domain (left) and ICIC in frequency and power domains (right)
ICIC on PDCCH? The existing traffic-channel ICIC algorithms will not directly work on PDCCH, because PDCCH has a very different channel structure and is much less flexible. First of all, the scheduler does not have the freedom of trying to avoid co-channel interference by dynamically restricting the PDCCH bandwidth as it does with traffic channel RBs. Secondly; there are no X2 messages that support ICIC on PDCCH, at least not in the current release. CCE-based power boost is one way the scheduler can play in the power domain. CCE aggregation level can be 1, 2, 4 or 8 (CCE-1, CCE-2, CCE-4 or CCE-8). The higher the aggregation level, the more robust it will be. However, high aggregation levels also use more PDCCH resources. Therefore, cell-center users will use CCE-1 or CCE-2; users located somewhere in the middle will use CCE-2 or CCE-4; cell-edge users will always use CCE-8. CCE-based power boost can boost up the transmit power level on CCE-8, which can potentially increase the signal level on CCEs for cell-edge users. How effective is the CCE-based power boost? Cells in a network can be in one of the following three scenarios:
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 55
COVERAGE-LIMITED ENVIRONMENT:
The cells are spaced very far apart from each other. Examples are rural and highway cells. Typically the signal levels near the cell edges are already very low; as a result, the out-of-cell interference levels are also very low. For coverage-limited environments, one can approximate using the formula below:
In this case, boosting the signal power enhances S, and thus improves SNR since thermal noise is just a constant. So CCE-based power boost is effective in a coveragelimited environment.
INTERFERENCE-LIMITED ENVIRONMENT:
The cells are packed very close to each other. Examples are dense suburban, urban or dense urban with small cells. Typically the cell-edge composite signal level is very high, but the out-of-cell interference level is also very high. As a result, the cell-edge SINR is still poor. For interference-limited environment, one can approximate using the formula below:
In this case, CCE-based power boost will not be effective, because when signal power is boosted up, the out-of-cell interference level is also increased, and as a result the SIR is not improved. Generally, when cell-edge power level is already very high, boosting the power further will not help. o This phenomenon is the so-called cocktail party effect: in a cocktail party with high noise level in the background, it does not improve audibility if everyone increases their voice level; it just creates a higher level of background noise. o Unfortunately, an interference-limited environment is the area where help is most needed. Call drops happen most frequently in small cells, especially calls placed from fast-moving vehicles.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 56
Figure 30
Interference also works against MIMO spatial multiplexing which requires good signal quality to operate. Hence, it is likely that in large percentage of the cell coverage area, MIMO-SM is not operational due to interference, which results in lower capacity. Consider that peak LTE rates include a MIMO-SM capacity gain factor of 2, so the downlink LTE throughput for a 20 MHz channel is about 150 Mbps, or a spectral
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 57
efficiency (SE) of 7.5 b/s/Hz. Losing MIMO-SM halves the spectral efficiency down to 3.75 b/s/Hz. The table below shows the average capacity for different LTE channelizations and corresponding spectral efficiency. Smaller channels have provide lower spectral efficiency that larger once because of control signaling overhead and loss of scheduling gain.
Channel Bandwidth 1.4 MHz 3 MHz 5 MHz 10 MHz 15 MHz 20 MHz SE Relative to 10 MHz 62% 83% 99% 100% 100% 103% Average Capacity (Mbps) 1.56 4.48 8.91 18 27 37.08 Average UL Capacity 0.8 2.1 3.6 8 11 16 (Mbps) To conclude, single channel LTE networks will offer an improvement in spectral efficiency over current 3G networks, but those expecting 150 Mbps download speeds will be disappointed. Network operators cannot plan their network capacity based on peak rates, but they will do so based on average rates which will be on the order of 1.4 1.8 b/s/Hz in the downlink.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 58
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 59
case of 10 MHz channel bandwidth. Comprehensive simulation-based analysis indicates that 123 VoIP users can be supported in 5 MHz bandwidth [2], implying (123*2= 246) users can be supported in 10 MHz channel bandwidth. The VoIP capacity estimate calculated above can be adjusted by modifying assumptions and making suitable adjustments to the calculations. For example, instead of using just two combinations of modulation scheme and coding rate, multiple combinations can be used to estimate the number of PRBs required by an average user in a cell. The overall approach outlined above can still be used for an approximate VoIP capacity estimate. Several factors would increase the VoIP capacity estimated above. If many users can work with reduced degree of channel coding, capacity would be higher. We did not use 64-QAM in the analysis above, because only UE Category 5 can support such scheme in the uplink, and we may not see such UEs for quite some time. Use of antenna techniques would also increase the capacity. Consideration of the voice activity factor would also increase capacity because we do not need to send hundreds of speech bits during the silence interval. Some factors would decrease the VoIP capacity estimated above. If many users in the cell need more redundancy than that provided by (1/3) coding, we would need more PRBs per user, reducing the capacity. If semi-persistent scheduling is not used, higher control channel overhead would decrease the achievable VoIP capacity. In summary, a 10 MHz channel bandwidth could support about 250 VoIP users in LTE.
LTE Drive Testing, Radio Network Planning & Optimization Version -01.01
| 60
12 REFERENCES
[1] 3GPP, 36.104V8.7.0.
[2] 3GPP, R1-072570, Performance Evaluation Checkpoint: VoIP Summary. [3] LTE in Bullets [4] 3GPP TR-25.814- V7.1.0, Physical Layer Aspects for E-UTRA, ANNEX A: Simulation Scenarios, page 116. [5] 3GPP TS-36.331- V10.2.0, Radio Resource Control Protocol Specification, Section 5.5.4.4: Event A3 (Neighbor becomes offset better than PCell), page 84. [6] 3GPP TS-36.300- V10.4.0, Overall Description, Section 10.1.2, Mobility Management in ECM-CONNECTED, subsection 10.1.2.1.1, C-plane handling, page 62. [6] 3GPP TS 36.133- V10.3.0, Requirements for support of Radio Resource Management, Section 7.6 Radio Link Monitoring, page 45. [7] 3GPP TS-36.300 -V10.4.0, Overall Description, Section 10.12.6 Radio Link Failure, page 72.