Professional Documents
Culture Documents
1. General description
74AHC1G02 and 74AHCT1G02 are high-speed Si-gate CMOS devices. They provide a 2-input NOR function. The AHC device has CMOS input switching levels and supply voltage range 2 V to 5.5 V. The AHCT device has TTL input switching levels and supply voltage range 4.5 V to 5.5 V.
2. Features
I I I I I I Symmetrical output impedance High noise immunity Low power dissipation Balanced propagation delays SOT353-1 and SOT753 package options ESD protection: N HBM JESD22-A114E: exceeds 2000 V N MM JESD22-A115-A: exceeds 200 V N CDM JESD22-C101C: exceeds 1000 V I Specied from 40 C to +125 C
3. Ordering information
Table 1. Ordering information Package Temperature range 74AHC1G02GW 74AHCT1G02GW 74AHC1G02GV 74AHCT1G02GV 40 C to +125 C SC-74A 40 C to +125 C Name TSSOP5 Description plastic thin shrink small outline package; 5 leads; body width 1.25 mm plastic surface-mounted package; 5 leads Version SOT353-1 SOT753 Type number
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
4. Marking
Table 2. Marking codes Marking AB A02 CB C02 Type number 74AHC1G02GW 74AHC1G02GV 74AHCT1G02GW 74AHCT1G02GV
5. Functional diagram
B 1 2 B A Y 4 1 2 A
mna103 mna104 mna105
6. Pinning information
6.1 Pinning
74AHC1G02 74AHCT1G02
B A 1 2 5 VCC
GND
3
001aaf095
74AHC_AHCT1G02_6
2 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
7. Functional description
Table 4. Function table H = HIGH voltage level; L = LOW voltage level Inputs A L L H H B L H L H Output Y H L L L
8. Limiting values
Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VCC VI IIK IOK IO ICC IGND Tstg Ptot
[1] [2]
Parameter supply voltage input voltage input clamping current output clamping current output current supply current ground current storage temperature total power dissipation
Conditions
Unit V V mA mA mA mA mA C mW
VI < 0.5 V VO < 0.5 V or VO > VCC + 0.5 V 0.5 V < VO < VCC + 0.5 V
[1]
20 75 65
Tamb = 40 C to +125 C
[2]
The input and output voltage ratings may be exceeded if the input and output current ratings are observed. For both TSSOP5 and SC-74A packages: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K.
74AHC_AHCT1G02_6
3 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V input capacitance HIGH-level input voltage LOW-level input voltage VCC = 4.5 V to 5.5 V VCC = 4.5 V to 5.5 V
For type 74AHCT1G02 VIH VIL VOH 2.0 0.8 2.0 0.8 2.0 0.8 V V
HIGH-level VI = VIH or VIL; VCC = 4.5 V output voltage IO = 50 A IO = 8.0 mA LOW-level VI = VIH or VIL; VCC = 4.5 V output voltage IO = 50 A IO = 8.0 mA input leakage current VI = 5.5 V or GND; VCC = 0 V to 5.5 V
4.4 3.94 -
4.5 0 -
4.4 3.8 -
4.4 3.70 -
V V V V A
VOL
II
74AHC_AHCT1G02_6
4 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
Table 7. Static characteristics continued Voltages are referenced to GND (ground = 0 V). Symbol Parameter ICC ICC Conditions Min supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V additional per input pin; VI = 3.4 V; supply current other inputs at VCC or GND; IO = 0 A; VCC = 5.5 V input capacitance 25 C Typ Max 1.0 1.35 40 C to +85 C 40 C to +125 C Unit Min Max 10 1.5 Min Max 40 1.5 A mA
CI
1.5
10
10
10
pF
25 C Typ Max
[2]
ns ns ns ns pF
[3]
3.5 4.9 19
5.5 7.5 -
1.0 1.0 -
6.5 8.5 -
1.0 1.0 -
7.0 9.5 -
ns ns pF
tpd is the same as tPLH and tPHL. Typical values are measured at VCC = 3.3 V. Typical values are measured at VCC = 5.0 V. CPD is used to determine the dynamic power dissipation PD (W). PD = CPD VCC2 fi + (CL VCC2 fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in Volts.
NXP B.V. 2007. All rights reserved.
74AHC_AHCT1G02_6
5 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
12. Waveforms
A, B input
VM
tPHL
tPLH
Y output
VM
mna106
Fig 5. The inputs (A and B) to output (Y) propagation delays Table 9. Type 74AHC1G02 74AHCT1G02 Measurement point Input VI GND to VCC GND to 3.0 V VM 0.5 VCC 1.5 V Output VM 0.5 VCC 0.5 VCC
VO
mna101
Test data is given in Table 8. Denitions for test circuit: CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator.
74AHC_AHCT1G02_6
6 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
A X
c y HE v M A
4
A2 A1 (A3) A
1
e e1 bp
3
w M detail X
Lp L
1.5 scale
3 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.1 0 A2 1.0 0.8 A3 0.15 bp 0.30 0.15 c 0.25 0.08 D(1) 2.25 1.85 E(1) 1.35 1.15 e 0.65 e1 1.3 HE 2.25 2.0 L 0.425 Lp 0.46 0.21 v 0.3 w 0.1 y 0.1 Z(1) 0.60 0.15 7 0
Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT353-1 REFERENCES IEC JEDEC MO-203 JEITA SC-88A EUROPEAN PROJECTION ISSUE DATE 00-09-01 03-02-19
7 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
SOT753
HE
v M A
A A1 c
3
detail X
Lp
bp
w M B
1 scale
2 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.9 A1 0.100 0.013 bp 0.40 0.25 c 0.26 0.10 D 3.1 2.7 E 1.7 1.3 e 0.95 HE 3.0 2.5 Lp 0.6 0.2 Q 0.33 0.23 v 0.2 w 0.2 y 0.1
EUROPEAN PROJECTION
8 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
14. Abbreviations
Table 10. Acronym CDM DUT ESD HBM MM TTL Abbreviations Description Charged Device Model Device Under Test ElectroStatic Discharge Human Body Model Machine Model Transistor-Transistor Logic
The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Package SOT353 changed to SOT353-1 in Section 3 and Section 13. Quick reference data and Soldering sections removed. Product specication Product specication Product specication Product specication Preliminary specication 74AHC_AHCT1G02_4 74AHC_AHCT1G02_3 74AHC_AHCT1G02_2 74AHC_AHCT1G02_1 -
74AHC_AHCT1G02_N_1 19981125
74AHC_AHCT1G02_6
9 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
Denition This document contains data from the objective specication for product development. This document contains data from the preliminary specication. This document contains the product specication.
Please consult the most recently issued document before initiating or completing a design. The term short data sheet is explained in section Denitions. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
16.2 Denitions
Draft The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales ofce. In case of any inconsistency or conict with the short data sheet, the full data sheet shall prevail.
malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customers own risk. Applications Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specied use without further testing or modication. Limiting values Stress above one or more limiting values (as dened in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/prole/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
16.3 Disclaimers
General Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
74AHC_AHCT1G02_6
10 of 11
NXP Semiconductors
74AHC1G02; 74AHCT1G02
2-input NOR gate
18. Contents
1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 1 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Recommended operating conditions. . . . . . . . 3 Static characteristics. . . . . . . . . . . . . . . . . . . . . 4 Dynamic characteristics . . . . . . . . . . . . . . . . . . 5 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 7 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . 9 Legal information. . . . . . . . . . . . . . . . . . . . . . . 10 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 10 Denitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Contact information. . . . . . . . . . . . . . . . . . . . . 10 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section Legal information.
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 30 May 2007 Document identifier: 74AHC_AHCT1G02_6