Professional Documents
Culture Documents
, LTD MC34063A
DC TO DC CONVERTER CONTROLLER
DESCRIPTION
The UTC MC34063A is a monolithic regulator subsystem, intended for use as DC to DC converter. This device contains a temperature compensated band gap reference, a duty-cycle control oscillator, driver and high current output switch. It can be used for step down, step-up or inverting switching regulators as well as for series pass regulators.
FEATURES
* Operation from 3.0V to 40V. * Short circuit current limiting. * Low standby current. * Output switch current of 1.5A without external transistors. * Frequency of operation from 100Hz to 100kHz. * Step-up, step-down or inverting switch regulators.
ORDERING INFORMATION
Normal MC34063A-D08-T MC34063A-S08-R Ordering Number Lead Free MC34063AL-D08-T MC34063AL-S08-R Halogen Free MC34063AG-D08-T MC34063AG-S08-R Package DIP-8 SOP-8 Packing Tube Tape Reel
1 of 10 QW-R103-008,H
MC34063A
PIN CONFIGURATION
PIN DESCRIPTION
PIN NAME Switch Collector Switch Emitter Timing Capacitor GND Comparator Inverting Input VCC IPEAK Sense Driver Collector I/O I O DESCRIPTION Internal Darlington pairs TI collector Internal Darlington pairs TI emitter The value of selected capacitor controls the internal oscillator run rate Inverting input of comparator which can set & initiate the Darlington pairs output switch Current sense input to monitor the voltage drop across an external resistor placed in series with VCC Internal Darlington pairs TI collector
PIN NO 1 2 3 4 5 6 7 8
I I
2 of 10 QW-R103-008,H
MC34063A
BLOCK DIAGRAM
T2
S R D C Is
Drive Collector
IPEAK Sense
CT
OSCILLATOR
Vcc
GND
1.25VREF
3 of 10 QW-R103-008,H
MC34063A
ABSOLUTE MAXIMUM RATINGS (Ta=25C )
PARAMETER Supply Voltage Comparator Input Voltage Range Switch Collector Voltage Switch Emitter Voltage Switch Collector to Emitter Voltage Driver Collector Voltage Switch Current
RATINGS UNIT 40 V -0.3 ~ +40 V 40 V 40 V 40 V 40 V 1.5 A DIP-8 1250 Power Dissipation (Ta=25C) PD mW SOP-8 625 Junction Temperature TJ +150 C Operating Temperature TOPR 0 ~ +70 C Storage Temperature TSTG -65 ~ +150 C Note: Absolute maximum ratings are those values beyond which the device which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied.
THERMAL DATA
PARAMETER SYMBOL DIP-8 SOP-8 JA RATINGS 100 160 UNIT /W
Junction-to-Ambient
PARAMETER Oscillator Charging Current Discharging Current Oscillator Amplitude Discharge to Charge Current Ratio Current limit Sense Voltage Output Switch Saturation Voltage 1(Note) Saturation Voltage 2(Note) DC Current Gain(Note) Collector Off State Current(Note) Comparator Threshold Voltage Threshold Voltage Line Regulation Input Bias Current Total Device Supply Current
50
VCC=5~40V, CT=0.001 V7=VCC, VC>VTHD, Pin2=GND Note: Output switch tests are performed under pulsed conditions to minimize power dissipation.
4 of 10 QW-R103-008,H
MC34063A
STEP-UP CONVERTER
170H L 8 180 S Q R 7 IPK RSC 0.22 VIN12V 6 + 100 VCC + - Comp. 5 R2 R1 2.2k 47k 330 1.25V REF REG OSC CT 3 CT 1500pF 4 Q2 Q1 2 1
1N5819
Test Line Regulation Load Regulation Output Ripple Efficiency Output Ripple With Optional Filter
Conditions VIN = 8.0V ~ 16V, IOUT = 175mA VIN = 12V, IOUT = 75mA ~ 175mA VIN = 12V, IOUT = 175mA VIN = 12V, IOUT = 175mA VIN = 12V, IOUT = 175mA
5 of 10 QW-R103-008,H
MC34063A
STEP-DOWN CONVERTER(Cont.)
Test Line Regulation Load Regulation Output Ripple Short Circuit Current Efficiency Output Ripple With Optional Filter
Conditions VIN = 15V ~ 25V, IOUT = 500mA VIN = 25V, IOUT = 50mA ~ 500mA VIN = 25V, IOUT = 500mA VIN = 25V, RL = 0.1 VIN = 25V, IOUT = 500mA VIN = 25V, IOUT = 500mA
6 of 10 QW-R103-008,H
MC34063A
VOLTAGE INVERTING CONVERTER
Test Line Regulation Load Regulation Output Ripple Short Circuit Current Efficiency Output Ripple With Optional Filter
Conditions VIN = 4.5V ~ 6.0V, IOUT = 100mA VIN = 5.0V, IOUT = 10mA ~ 100mA VIN = 5.0V, IOUT = 100mA VIN = 5.0V, RL = 0.1 VIN = 5.0V, IOUT = 100mA VIN = 5.0V, IOUT = 100mA
7 of 10 QW-R103-008,H
MC34063A
8 of 10 QW-R103-008,H
MC34063A
TYPICAL CHARACTERISTICS
9 of 10 QW-R103-008,H
MC34063A
DESIGN FORMULA TABLE
CALCULATION tON tOFF (tON+tOFF)MAX CT 4x10-5 tON 2IOUT(MAX) 0.3/ISW STEP-DOWN
STEP-UP
VOLTAGE-INVERTING
VOUT + VF VIN - VCE(SAT)
4x10-5 tON
4x10-5 tON
ISW
RS L(MIN) CO
0.3/ISW
0.3/ISW
VCE(SAT) - Saturation voltage of the output switch. VF - Forward voltage drop of the ringback rectifier. The following power supply characteristics must be chosen: - Nominal input voltage. VIN VOUT - Desired output voltage, VOUT =1.25(1+R2/R1) - Desired output current. IOUT FMIN - Minimum desired output switching frequency at the selected values for VIN and IOUT. VRIPPLE(P-P) - Desired peak-to-peak output ripple voltage. In practice, the calculated value will need to be increased due to the capacitor equivalent series resistance and board layout. The ripple voltage should be kept to a low value since it will directly effect the line and load regulation.
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
10 of 10 QW-R103-008,H