Professional Documents
Culture Documents
References
BTS3006C System Description BTS3006C Hardware Installation Manual BTS3006C Hardware Description Manual
Page 1
Upon completion of this course, you will be able to: Know the functions and features of BTS Master the BTS hardware structure Master the cable connection of BTS
Page 2
Chapter 1 Overview of BTS3006C Chapter 2 BTS3006C Hardware Structure Chapter 3 BTS3006C Signal Processing Chapter 4 BTS3006C Typical Configuration
Page 3
Location of BTS3006C
Um Interface
TUP,ISUP
HLR/AUC/EIR
SMC/VM
MS: Mobile Station HLR: Home Location Register MSC: Mobile Switching Center VM: Voice Mailbox
BTS: Base Transceiver Station AUC: Authentication Center VLR: Visitor Location Register
BSC: Base Station Controller EIR: Equipment Identity Register SMC: Short Message Center
Page 4
Chapter 1 Overview of BTS3006C Chapter 2 BTS3006C Hardware Structure Chapter 3 BTS3006C Signal Processing Chapter 4 BTS3006C Typical Configuration
Page 7
Page 8
BTS3006C Cabinet
Item Width (mm) 600 600 600 Depth (mm) 470 470 470 Height (mm) 700 900 980
Page 9
DAFM 3
DAFM 1
DPSM/ DSEM
DDRM2
DDRM1
DDRM 0
DAFM 2
DAFM 0
DMCM
FAN 2
FAN 1
FAN 0
Page 10
Modules of BTS3006C
Subsystem Module Full Name Number in a Single Cabinet Maximum Common subsystem Doubletransceiver subsystem RF front-end subsystem DMCM DBMB DDRM Main Control Module for DDRM BTS Module Backplane Double transceivers Digital and Radio frequency Module Double Duplexer Module for DDRM BTS Double Combining Module for DDRM BTS Single Combining Module for DDRM BTS Antenna and TMA Control Module for DDRM BTS Power Supply Module for DDRM BTS DC SPD and EMI Module 1 1 3 Minimum 1 1 1
4 2 1 1 1 1
1 0 0 0 0 0
Power subrack
DPSM DSEM
Page 11
DDPM
. .
TMA
TMA
Abis
Common subsystem
Antenna subsystem
Page 12
Page 13
Common Subsystem
The common subsystem consists of the DMCM and the DBMB. Functions of common subsystem. Remotely connecting the BTS to the BSC, monitoring the heater, downloading software and operating and maintaining the entire BTS Performing the electrical interconnection of each subsystem through the DBMB Performing clock, fault, configuration, performance and security management Supporting E1 and STM-1 transmission Detecting alarms of external equipment and external fans, detecting the temperature, lightning protection and door status alarms Supporting flexible topologies: Ring, chain, star, and hybrid topologies
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 14
Panel of DMCM
Page 16
Indicators of DMCM
Indicator RUN Color Green Description Indicates the operation status of the module Status Blinks slowly (On for 2s and off for 2s) Blinks slowly (On for 1s and off for 1s) Blinks at irregular intervals Off MOD Green Indicates the transmission mode On Blinks rapidly (On for 0.25s and off for 0.25s) Off LIU0~3 Green Indicates the transmission status of E1 port 0~3 On Blinks rapidly (On for 1s and off for 1s) Off Meaning The OML is blocked. Normal BSC data loading Power failure of the DMCM E1 transmission Optical transmission
Page 17
Indicators of DMCM
Indicator PLL Color Green Description Indicates the operation status of the phase-locked loop Indicates the operation status of the IASU Status On On for 0.125s and off for 0.125s On for 0.5s and off for 0.5s Off TRUN Green On on for 1s and off for 1s on for 0.25s and off for 0.25s Off OPTW Green Indicator on the westward optical port On Blinks rapidly (on for 1s and off for 1s) Off Meaning Free-run Pull-in Locked Abnormal CBUS2 link broken The IASU works normally. The IASU is faulty. The MCU is not configured with the IASU. Terminal alarm on the westward optical port Remote alarm on the westward optical port The optical channel is normal.
Page 18
Indicators of DMCM
Indicator OPTE Color Green Description Indicator on the eastward optical port Status On Blinks rapidly (on for 1s and off for 1s) Off HEATER Red Indicates the operation status of the heater Optical port 1 for the combined cabinets On Off Off On Blinks rapidly (0.25s on and 0.25s off) SFP-B Green Optical port 2 for the combined cabinets Off On Blinks rapidly (on for 0.25s and off for 0.25s) HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Meaning Terminal alarm on the eastward optical port Remote alarm on the eastward optical port Normal Powered on Powered off Normal SFP-A terminal alarm SFP-A remote alarm Normal SFP-B terminal alarm SFP-B remote alarm
SFP-A
Green
Page 19
Ports of DMCM
Port SFP-A SFP-B MMI TIU 13M FC/2M DOOR E1_0/1 E1_2/3 ALM OPT Connector SFP SFP RJ45 RJ45 SMB SMB Common Cylindrical (waterproof) Cylindrical (waterproof) Cylindrical (waterproof) Cylindrical (waterproof) Remarks Optical module A in the combined cabinets Optical module B in the combined cabinets Terminal maintenance port IASU terminal maintenance port 13 Mbit/s test clock output Frame clock, 2 Mbit/s clock Door status port Port for E1 cables 0 and 1 Port for E1 cables 2 and 3 One route of RS485 full-duplex serial port alarm Four routes of main nodes alarm Optical transmission port
Page 20
Page 21
Page 22
Double-Transceiver Subsystem
The double-transceiver subsystem consists of the DDRM and fan units. The functions of double-transceiver subsystem include Processing baseband signals Transmit diversity and 4-way receive diversity Synthesizing frequencies Performing loopback test Amplifying power and then transmitting it through two TRXs individually Supplying power to the fans and monitoring the fans Supporting one fan for one DDRM Supporting replacement of at least one fan at a time
Page 23
Off Blinks slowly (on for 1s and off for 1s) ALM Red Alarm indicator On (blinks at high frequency) Off RF_IND Red RF port indicator Off Blinks slowly (on for 1s and off for 1s)
Page 25
Page 26
TRX0 TRX0
TX2
RXM1 RXD1
RXM2 RXD2
TRX1 TRX1
Page 27
Page 28
TX
TRX0 TRX0
TX2
TX
TRX1 TRX1
Page 29
TRX0 TRX0
TX2
TX
TRX1 TRX1
Page 30
Page 31
TRX0 TRX0
TX2
RXM1
divider divider
RXD1
TX divider divider
RXM2 RXD2
TRX1 TRX1
Page 32
TRX0 TRX0
TX2
RXM1
divider divider
RXD1
divider divider
TX
RXM2 RXD2
TRX1 TRX1
Page 33
TX1
TX
TRX0 TRX0
TX2
RXM1
divider divider
TX divider divider
TRX1 TRX1
Page 34
Index 1 2 3 4 5 6 7
Name
Waterproof module Base of the door status switch E1 cable (0,1) E1 cable (2,3) External alarm cable SDH external optical cable Fan
Page 35
Page 36
RF Front-End Subsystem
The RF front-end subsystem consists of the antenna subsystem and the DAFM subsystem.
RF Front-End Subsystem Antenna subsystem Component Antenna Feeder TMA DAFM subsystem DDPM Function Transmits and receives signals Connects the antenna to port ANTA or ANTB on the DDPM Amplifies the signal received by the antenna Sends the multiple channels of the RF signals from the transceiver to the antenna through the duplexer Amplifies the received signals from the antenna and divides the signals into three parts and then sends them to the transceiver Controls the low noise amplification Double combination (used for the single combination in single sector with no more than four carriers) Single combination (used for the double combinations in single sector with five or six carriers) Supplies power for the TMA All rights reserved Page 37
Function of DDPM
The DDPM is placed in the DAFM slot. It is mandatory. There are a maximum of four DDPMs and a minimum of one DDPM.
The DDPM performs the following functions:
Sending multiple routes of RF signals from the transceiver to the antenna through the duplexer Sending signals from the antenna to the receiver after amplifying and dividing them into three parts Detecting VSWR alarms in the antenna system Receiving the gain control of the low noise amplifier
Page 38
Indicators of DDPM
Indicator RUN Color Green Descripti on Indicates the operation status of the DDPM Status On Off Blinks slowly (on for 1s and off for 1s) Blinks rapidly (on for 0.5s and off for 0.5s) Blinks rapidly (on for 0.25s and off for 0.25s) ALM Red Alarm indicator On Off Blinks slowly (on for 1s and off for 1s) VSWRA Red Channel A VSWR alarm indicator Channel B VSWR alarm indicator Blinks slowly (on for 1s and off for 1s) On Off Blinks slowly (on for 1s and off for 1s) On Off Meaning There is power input, and the DDPM is faulty. There is no power input, or the DDPM is faulty. The DDPM works normally. Software is being loaded The write-protect function is disabled or the software is undergoing an ageing test. Alarms including VSWR alarm indicate that there are faults. Normal The DDPM is starting or loading the latest application. Channel A VWSR alarm Critical channel A VSWR alarm No channel A VSWR alarm Channel B VWSR alarm Critical channel B VSWR alarm No channel B VSWR alarm
VSWRB
Red
Page 39
Ports of DDPM
Port TXA Connector N (female) Remarks Inputs TX signals from the DDRM Inputs combined signals from the DDCM or the DSCM Inputs TX signals from the DDRM Inputs combined signals from the DDCM or the DSCM Output port for main diversity 1 Output port for main diversity 2 Output port for main diversity 3 Output port for diversity 1 Output port for diversity 2 Output port for diversity 3 Connects to the 1/4-inch jumper Connects to the 1/4-inch jumper
TXB
N (female)
SMA (female) SMA (female) SMA (female) SMA (female) SMA (female) SMA (female) N (female) N (female)
Page 40
Function of DDCM
The DDCM is placed in the DAFM slot. It is optional. There are a maximum of two DDCMs The DDCM combines two channels of transmit signals from the DDRM before sending the signals to the DDPM or the DSCM DDCM can only be used for first combination
Page 41
Ports of DDCM
Port TXA1 TXA2 COMA TXB1 TXB2 COMB Connector N (female) N (female) N (female) N (female) N (female) N (female) Remarks Inputs the TX signals from the DDRM Inputs the TX signals from the DDRM Outputs the combined signals to the DDPM Inputs the TX signals from the DDRM Inputs the TX signals from the DDRM Outputs the combined signals to the DDPM
Page 42
Page 43
Port ANT0~5
Page 44
Indicators of DATM
Indicator RUN Color Green Description Indicates that the DATM is working Status Blinks slowly (on for 1s and off for 1s) Blinks slowly (on for 0.5s and off for 0.5s) Blinks rapidly (on for 0.25s and off for 0.25s) Off ACT Green Indicates the AISG link status On Off Blinks at irregular intervals ALM Red Alarm indicator On Off Meaning The power supply is normal, and communication between the DATM and the DMCM is abnormal. The DATM works and communicates with the DMCM normally. Loading programs
There is no power supply, or the DATM is faulty. The AISG link is normal. The AISG link is abnormal. AISG link transmission is under progress. The DATM has alarms such as overcurrent alarms. The DATM is normal.
Page 45
Page 46
Page 47
Page 48
Indicators of DPSM
Indicator INPUT OUTPUT FAIL Color Green Green Red Status On Off On Off On Off Meaning The power input is normal. The power input is abnormal. The power input is normal. The power input is abnormal. The DPSM is protected or is faulty. The DPSM works normally.
Page 49
DSEM
The DSEM is placed in the DPSM/DSEM slot. It is optional. There is only one DSEM.
Indicator INPUT Color Green Status On Off FAIL Red On Off Meaning The power input is normal. The power input is abnormal. The DSEM is protected or is faulty. The DSEM works normally.
Page 50
Page 51
Monitoring Subsystem
Monitor the internal environment , control and monitor the power supply and battery recharging, and report these information to DMCM Through ALM and DOOR ports on DMCM, DMCM gather all the environment information from different sensors , for example the temperature , humidity, smoke, water , door broken, etc. The DMCM will perform certain operation and then report it to maintenance center
Page 52
Chapter 1 Overview of BTS3006C Chapter 2 BTS3006C Hardware Structure Chapter 3 BTS3006C Signal Processing Chapter 4 BTS3006C Typical Configuration
Page 53
Signal Processing
Traffic signal flow Control signal flow Clock signal flow Cabinet group signal flow
Page 54
MS
Antenna Feeder D D D P M D D D P M D D P S M
D D P M
D D P M
D M C M
Abis
BTS3006C Cabinet
BSC
Page 55
Page 56
D D P M
D D P M
D P S M
D D P M
D D P M
D M C M
Abis
BTS3006C Cabinet
BSC
Page 57
Page 58
Page 59
Page 60
Fiber
Extension Cabinet in Basic Cabinet Group
Fiber
Basic Cabinet in Basic Cabinet Group
Fiber
Basic Cabinet in Extension Cabinet Group
Fiber
Fiber
Fiber
All signals between cabinets of BTS3006C cabinet group will be transmitted through the fibers between them, there is no other cables between two cabinets in one group
Page 61
Chapter 1 Overview of BTS3006C Chapter 2 BTS3006C Hardware Structure Chapter 3 BTS3006C Signal Processing Chapter 4 BTS3006C Typical Configuration
Page 62
S1/1/1Diversity Transmitter
DDPM
In this modeone DDRM and one DDPM refer to one sector, altogether 3 sectors. Every DDRM is treated as one carrier. The cabling of one sector is shown as the diagram, others are the same. BSC side data should be configured as: diversity transmitter and independent receiver Power output (dBm): 46 -1.0
TX B
TX A
ANT B
ANT A
TX 1
TX 2
DDRM
Page 63
S1/1/1 (Diversity Transmitter on the same antenna and Four Diversity Receiver)
In this mode, 1 DDRM and 2 DDPM refer to 1 sector, 2 antennas are needed. Every DDRM is treated as 1 carrier. The cabling of one sector is shown as the diagram, others are the same BSC side data should be configured as: diversity transmitter and four diversity receiver Power output (dBm): 46 -1.0
DDPM DDPM
TX B TX A TX B RXA1 RXA2 RXA3 TX A
ANT B
ANT A
ANT B
ANT A
TX 1
TX 2
DDRM
Page 64
TX B
TX B
ANT B
ANT A
ANT B
ANT A
TX 1
TX 2
DDRM
Page 65
In this mode, 1 DDRM and 1 DDPM refer to 1 sector, altogether 3 sectors. The cabling of one of them is shown as the diagram, others are the same BSC side data should be configured as : no combining and dividing receiver Power output (dBm): 46, -1.0
TX B
TX A
ANT B
ANT A
TX 1
TX 2
DDRM
Page 66
S1/1/1
The first two sectors of S1/1/1 share one DDRM, connect to two different DDPM for two different sectors. The third sector use the second DDRM and DDPM BSC side data should be configured as : DDRM0: no combining and independent receiver DDRM2: no combining and independent receiver or dividing receiver Power output (dBm)46 -1.0
HUAWEI TECHNOLOGIES CO., LTD.
DDPM DDPM DDPM
TX B TX A TX B TX A TX B TX A
ANT B
ANT A
ANT B
ANT A
ANT B
ANT A
TX 1
TX 1
TX 2
TX 2
DDRM
DDRM
Page 67
S1/2/1
Sector1 and 3 of S1/1/1 share one DDRM, connect to two different DDPMs for two different sectors. The second sector uses another DDRM and DDPM BSC side data should be configured as : DDRM0: no combining and independent receiver DDRM2: no combining and dividing receiver Power output (dBm)46 -1.0
HUAWEI TECHNOLOGIES CO., LTD.
DDPM DDPM DDPM
TX B TX A TX B TX A TX B TX A
ANT B
ANT A
ANT B
ANT A
ANT B
ANT A
TX 1
TX 1
TX 2
TX 2
DDRM
DDRM
Page 68
S3/3
DDPM DDCM
TXA1 TX B TX A TXA2 RXA1 RXA2 RXA3 TXB2 COMA TXB1 RXB3 RXB1 RXB2 TX B TX A
DDPM
Two sectors share DDRM1 BSC side data should be configured as: DDRM0DDRM2: no combining and dividing receiver DDRM1: no combining and independent receiver Power output of DDRM1: dBm46-1.0 Power output of DDRM0,2 dBm46-3-1.0
RXB1 RXB2 RXB3
TX 1
TX 1
TX 1
TX 2
TX 2
TX 2
DDRM
DDRM
DDRM
Page 69
Summary
Functions and features of BTS3006C BTS3006C hardware structure Signal flow of BTS3006C Typical configuration of BTS3006C
Page 70
Thank You
www.huawei.com