You are on page 1of 12

Flintlock

Flintlock of an 18th century hunting rifle, with flint missing.

Flintlock is the general term for any firearm based on the flintlock mechanism. The term may also apply to the mechanism itself. Introduced at the beginning of the 17th century, the flintlock rapidly replaced earlier firearm-ignition technologies, such as the doglock, matchlock and wheellock mechanisms. It continued to be in common use for over two centuries, replaced by percussion cap and, later, cartridge-based systems in the early-to-mid 19th century. Although long superseded by
modern firearms, flintlock weapons enjoy continuing popularity with black powder shooting enthusiasts.

Subtypes
Flintlocks may be any type of small arm: long gun or pistol, smoothbore or rifle, muzzleloader or breechloader.

Pistols

French flintlock pistol circa 1790-1795

Flintlock pistols were used as self-defense weapons and as a military arm. Their effective range was short, and they were frequently used as an adjunct to a sword or cutlass. Pistols were usually smoothbore although some rifled pistols were produced.

Muskets
Main article: Musket

Flintlock mechanism

Flintlock muskets were the mainstay of European armies between 1660 and 1840. A musket was a muzzle-loading smoothbore long gun that was loaded with a round lead ball, but it could also be loaded with shot for hunting. For military purposes, the weapon was loaded with ball, or a mixture of ball with several large shot (called buck and ball), and had an effective range of about 75 to 100 meters. Smoothbore weapons that were designed for hunting birds were called "fowlers." Flintlock muskets tended to be of large caliber and usually had no choke, so they could also be used to fire a ball. Military flintlock muskets tended to weigh approximately ten pounds, as heavier weapons were found to be too cumbersome, and lighter weapons were not rugged or heavy enough to be used in hand to

hand combat. They were usually designed to be fitted with a bayonet. On modern weapons, bayonets are a last ditch weapon that rarely plays a significant role on the battlefield. On flintlocks, the bayonet played a much more significant role, often accounting for a third or more of all battlefield casualties. Flintlock weapons were not used like modern rifles. They tended to be fired in mass volleys, followed by bayonet charges in which the weapons were used much like the pikes that they replaced. Because they were used as pikes, military flintlocks tended to be approximately five or six feet in length (without the bayonet attached), and used bayonets that were approximately 18 to 22 inches in length.

Rifles
Some flintlocks were rifled. The spiral grooves of rifling make rifles more accurate and give a longer effective ranges but on a muzzle-loading firearm they take more time to load due to the tight-fitting ball, and after repeated shots black powder tended to foul the barrels. Military musketeers could not afford to take the time to clean their barrels in between shots and the rifle's greater accuracy was unnecessary when tactics were based on mass volleys. Most military flintlocks were therefore smoothbore. Rifled flintlocks did see some military use by sharpshooters, skirmishers, and other support units; but most rifled flintlocks were used for hunting. By the late 18th century there were increasing efforts to take advantage of the rifle for military purposes, with specialist rifle units such as the King's Royal Rifle Corps of 1756 and Rifle Brigade (Prince Consort's Own) of 1800. Despite this, smoothbores predominated until the advent of the Mini ball by which time the percussion cap had made the flintlock obsolete. In the United States, modifications to small game rifles originally designed in Europe led to the long rifle ("Pennsylvania Rifle" or "Kentucky Rifle,") which due to their long barrels were exceptionally accurate for their time, with an effective range of approximately 250 meters. [1] Since Pennsylvania/Kentucky rifles were used primarily for hunting, they tended to fire smaller caliber rounds, with calibers in the range of .32 to .45 being common. This type of rifle was sometimes referred to as a "pea rifle" since the round ball was approximately the same size as a pea. [2] The jezail was another example of a long flintlock rifle, but its use in Afghanistan, India, Central Asia and parts of the Middle East was primarily as a military weapon, so tended to fire a larger and heavier round.

Multishot flintlock weapons


Multiple barrels

A three barrel flintlock pistol.

Because of the time needed to reload (even experts needed 15 seconds to reload a smooth-bore, muzzle-loading musket[3]), flintlocks were sometimes produced with two, three, four or more barrels for multiple shots. These designs tended to be costly to make and were often unreliable and dangerous. While weapons like double barreled shotguns were reasonably safe, weapons like the pepperbox revolver would sometimes fire all barrels simultaneously, or would sometimes just explode in the user's hand. It was often less expensive, safer, and more reliable to carry several single-shot weapons instead.

Single barrel
Some repeater rifles, multishot single barrel pistols, multishot single barrel revolvers, ... were also made. Notable are the Puckle gun, Mortimer[4], Kalthoff, Michele Lorenzoni, Abraham Hill, Cookson pistols[5], the Jennings repeater and the Elisha Collier revolver.[6][7][8][9][10]

Drawbacks

Scottish Flintlock pistol: David McKenzie, a Dundee gunsmith made this pistol. The heart shaped butt is commonly found on pistols made in Scotland. The gun is steel with silver inlay showing Celtic designs. Flintlocks were prone to many problems, compared to modern weapons. Misfires were common. The flint had to be properly maintained, as a dull or poorly napped piece of flint would not make as much of a spark and would increase the misfire rate dramatically. Moisture was a problem, since moisture on the frizzen or damp powder would prevent the weapon from firing. This meant that flintlock weapons could not be used in rainy or damp weather. Some armies attempted to remedy this by using a leather cover over the lock mechanism, but this proved to have only limited success. [11] Accidental firing was also a problem for flintlocks. A burning ember left in the barrel could ignite the next powder charge as it was loaded. This can be avoided by waiting between shots for any leftover residue to completely burn. Running a lubricated cleaning patch down the barrel with the ramrod will also extinguish any embers, and will clean out some of the barrel fouling as well. Soldiers on the battlefield could not take these precautions though. They had to fire as quickly as possible, often firing three to four rounds per minute. Loading and firing at such a pace dramatically increased the risk of an accidental discharge.

When a flintlock is fired it sprays a shower of sparks forwards from the muzzle and another sideways out of the flash-hole. One reason for firing in volleys was to ensure that one man's sparks didn't ignite the next man's powder as he was in the act of loading. An accidental frizzen strike can also ignite the main powder charge, even if the pan has not yet been primed. Some modern flintlock users will place a leather cover over the frizzen while loading as a safety measure to prevent this from happening. This also slows down the loading time, which prevented safety practices such as this from being used on the battlefield. The black powder used in flintlocks would quickly foul the barrel, which was a problem for rifles and for smooth bore weapons that fired a tighter fitting round for greater accuracy. Each shot would add more fouling to the barrel, making the weapon more and more difficult to load. Even if the barrel was badly fouled, the flintlock user still had to properly seat the round all the way to the breech of the barrel. Leaving an air gap in between the powder and the round (known as "short starting") was very dangerous, and could cause the barrel to explode. Handling loose black powder was also dangerous, for obvious reasons. Powder measures, funnels, and other pieces of equipment were usually made out of brass to reduce the risk of a static discharge which could ignite the powder. Soldiers often used pre-made "cartridges", which unlike modern cartridges were not inserted whole into the weapon. Instead, they were tubes of paper that contained a pre-measured amount of powder and a lead ball. Although paper cartridges were safer to handle than loose powder, their primary purpose was not safety related at all. Instead, paper cartridges were used mainly because they sped up the loading process. A soldier did not have to take the time to measure out powder when using a paper cartridge. He simply tore open the cartridge, used a small amount of powder to prime the pan, then dumped the remaining powder from the cartridge into the barrel. The black powder used in flintlocks contained sulfur. If the weapon was not cleaned after use, the powder residue would absorb moisture from the air and would combine it with the sulfur to produce sulfuric acid. This acid would erode the inside of the gun barrel and the lock mechanism. Flintlock weapons that were not properly cleaned and maintained would corrode to the point of being destroyed. Most flintlocks were produced at a time before modern manufacturing processes became common. Even in mass produced weapons, parts were often handmade. If a flintlock became damaged, or parts wore out due to age, the damaged parts were not easily replaced. Parts would often have to be filed down, hammered into shape, or otherwise modified so that they would fit, making repairs much more difficult. Machine-made, interchangeable parts only began to be used shortly before flintlocks were replaced by caplocks.

History
French courtier Marin le Bourgeoys made the first firearm incorporating a true flintlock mechanism for King Louis XIII shortly after his accession to the throne in 1610.[12] The development of firearm lock mechanisms had proceeded from matchlock to wheellock to snaplock to snaphance and miquelet in the previous two centuries, and each type had been an improvement, contributing some design features which were useful. Le Bourgeoys fitted these various features together to create the flintlock mechanism. The new system quickly became popular, and was known and used in various forms throughout Europe by 1630. In particular, dragoons serving with the Parliamentarian army in the

English Civil War were known to use snaphaunce muskets, or early forms of flintlocks. Examples of early flintlock weapons can be seen in the painting "Marie de' Medici as Bellona" by Rubens (painted around 1622-25). Various breech-loading flintlocks were developed starting around 1650. The most popular action has a barrel which was unscrewed from the rest of the gun. Obviously this is more practical on pistols because of the shorter barrel length. This type is known as a Queen Anne pistol because it was during her reign that it became popular (although it was actually introduced in the reign of King William III). Another type has a removable screw plug set into the side or top or bottom of the barrel. A large number of sporting rifles were made with this system, as it allowed easier loading compared with muzzle loading with a tight fitting bullet and patch. One of the more successful was the system built by Isaac de la Chaumette starting in 1704. The barrel and could be opened by 3 revolutions of the triggerguard, to which it was attached. The plug stayed attached to the barrel and the ball and powder were loaded from the top. This system was improved in the 1770s by Colonel Patrick Ferguson and 100 experimental rifles used in the American Revolutionary War. The only two flintlock breechloaders to be produced in quantity were the Hall and the Crespi. The first was invented by John Hall and patented c. 1817.[13] It was issued to the US Army as the Model 1819 Hall Breech Loading Rifle[14] The Hall rifles and carbines were loaded using a combustible paper cartridge inserted into the upward tilting breechblock. Hall rifles leaked gas from the often poorly fitted action. The same problem affected the muskets produced by Giuseppe Crespi and adopted by the Austrian Army in 1771. Nonetheless, the Crespi System was experimented with by the British during the Napoleonic Wars, and percussion Halls guns saw service in the American Civil War. Flintlock weapons were commonly used until the mid 19th century, when they were replaced by percussion lock systems. Even though they have long been considered obsolete, flintlock weapons continue to be produced today by manufacturers such as Pedersoli, Euroarms, and Armi Sport. Not only are these weapons used by modern re-enactors, but they are also used for hunting, as many U.S. states have dedicated hunting seasons for black powder weapons, which includes both flintlock and percussion lock weapons.

The flint for flintlock 17th century

Method of operation

A cock tightly holding a sharp piece of flint is rotated to half-cock, where the sear falls into a safety notch on the tumbler, preventing an accidental discharge.

The operator loads the gun, usually from the muzzle end, with black powder followed by lead shot, a round lead ball, usually wrapped in a piece of paper or a cloth patch, all rammed down with a ramrod that is usually stored on the underside of the barrel. The flash pan is primed with a small amount of very finely ground gunpowder, and the flashpan lid or frizzen is closed.

The gun is now in a "primed and loaded" state, and this is how it would typically be carried while hunting or if going into battle. To fire: The cock is further rotated from half-cock to full-cock, releasing the safety lock on the cock. The gun is leveled and the trigger is pulled, releasing the cock holding the flint. The flint strikes the frizzen, a piece of steel on the priming pan lid, opening it and exposing the priming powder. The contact between flint and frizzen produces a shower of sparks (burning pieces of the metal) that is directed into the gunpowder in the flashpan. The powder ignites, and the flash passes through a small hole in the barrel (called a vent or touchhole) that leads to the combustion chamber where it ignites the main powder charge, and the gun discharges. The Royal Infantry and Continental Army used paper cartridges to load their weapons.[15] The powder charge and ball were instantly available to the soldier inside this small paper envelope. To load a flintlock weapon using a paper cartridge, a soldier would move the cock to the half-cock position; tear the cartridge open with his teeth; fill the flashpan half-full with powder, directing it toward the vent; close the frizzen to keep the priming charge in the pan; pour the rest of the powder down the muzzle and stuff the cartridge in after it; take out the ramrod and ram the ball and cartridge all the way to the breech; replace the ramrod; shoulder the weapon. Now he is ready to place the weapon on full cock and fire on command.

Cultural impact
The flintlock mechanism was in main use for both military and civilian use for over 200 years. Not until the Reverend Alexander John Forsyth, a Scottish minister, invented the rudimentary percussion cap system in 1807 did the flintlock system begin to decline in popularity. The percussion-cap system replaced the flintlock's flint and flashpan with a waterproof copper cap that created a spark when struck. The percussion ignition system was more weatherproof and more reliable than the flintlock. The transition from flintlock to percussion cap was a slow one, even at that, since the percussion system was not widely used until around 1830. The Model 1840 U.S. musket was the last flintlock firearm produced for the U.S. military,[16] although obsolete flintlocks were seeing action in the earliest days of the American Civil War, for example, during the first year of the war, the Army of Tennessee had over 2,000 flintlock muskets in service. As a result of the flintlock's long active life, it has left lasting marks on the language and on drill and parade. Terms such as: "lock, stock and barrel", "going off half-cocked" and "flash in the pan" remain

current in the English language. In addition, the weapon positions and drill commands that were originally devised to standardize carrying, loading and firing a flintlock weapon remain the standard for drill and display (see manual of arms).

A flintlock musket being fired

Reproduction flintlock musket detail

ignition sequence

Exploded View of a Flintlock


The drawing below shows an exploded view of a Danish-Norwegian military flintlock. Note that he translation of this article is not quite finished.

Parts:
1. Cock screw 2. Cock spur 3. Neck of the cock 4. Body of the cock 5. Tumbler screw 6. Upper jaw 7. Piece of leather 8. Flint 9. Lower jaw 10. Face of frizzen (steel) 11. Pan cover 12. Tail of frizzen 13. Pan cover screw 14. Pressure arm 15. Frizzen spring 16. Frizzen spring screw 17. Pan 18. Lockplate 19. Threaded hole for foremost lock plate screw 20. Threaded hole for frizzen screw 21. Bolster 22. Pan screw 23. Threaded hole for rearmost lock plate screw 24. Anslagsflater 25. Studdelskrue 26. Studdel

27. Stangfjrskrue 28. Stangfjr 29. Stang 30. Stangskrue 31. Nuss 32. Nusskrapp 33. Tumbler hook of mainspring 34. Slagfjrskrue 35. Lower limb of mainspring 36. Slagfjrre 37. Upper limb of mainspring 38. Cup of tumbler 39. Stangarm 40. Gjengehull for slagfjrskrue 41. Gjengehull for fengpanneskrue 42. Gjengehull for stangfjrskrue 43. Gjengehull for stangskrue 44. Forsterkningsknast for gjengehull 45. Firkanttapp for hane 46. Nusstapp 47. Halvspennro 48. Helspennro 49. Springkile

Exploded View of a Flintlock Musket


The smoothbore military flintlock musket was the standard infantry firearm for hundreds of years before the percussion muskets and breech-loading rifles took over from the mid-1850s. The Norwegian Army received muskets from Denmark during the union years, but after the union with Denmark fell apart and another union was established with Sweden in 1814, the Norwegians started their own firearms production at Kongsberg. A typical Norwegian-Danish musket looked like this:

Parts:
1. Butt 2. Wrist 3. Comb 4. Heel 5. Butt plate with screws 6. Toe 7. Trigger guard 8. Flint lock 9. Barrel breech 10. Ramrod 11. Front sling swivel with screw 12. Thimble 13. Thimble pins 14. Entry thimble 15. Muzzle

16. Front sight 17. Bayonet lug 18. Ear for the sling swivel screw 19. Double ear pin ear for securing the thimbles 20. Single ear- pin ear - for securing the barrel to the stock 21. Flash hole 22. Rear sight notch 23. Tang 24. Breech plug 25. Barrel 26. Rear sling swivel with screw 27. Ramrod stopper 28. Trigger 29. Trigger guard screws 30. Trigger assembly 31. Bayonet socket 32. Elbow 33. Bayonet lug slot 34. Shoulder 35. Triangular blade 36. Front side plate screw 37. Rear side plate screw 38. Side plate 39. Muzzle cap 40. Tang screw 41. Brake spring for the ramrod 42. Back of the thimble 43. Butt nose 44. Barrel pin 45. Butt nose 46. Fore-stock 47. Cheek piece 48. Breech plug

See also

Matchlock Wheellock Caplock Snaplock Snaphance Miquelet Blunderbuss Queen Anne pistol Boyer Rifle Hand cannon

Notes

1. ^ "What about the rifle?", Popular Science, September 1941 2. ^ "American Rifle: A Treatise, a Text Book, and a Book of Practical Information in the Use of the Rifle" By Townsend Whelen, Publisher: Paladin Press (July 2006) 3. ^ Dennis E. Showalter, William J. Astore, Soldiers' lives through history: Volume 3: The early modern world, p.65, Greenwood Publishing Group, 2007 ISBN 0-313-33312-2. 4. ^ Mortimer multishot pistol 5. ^ Flintlock revolvers 6. ^ Mortimer multi-shot 7. ^ Another similar Mortimer pistol 8. ^ Jennings repeater 9. ^ Puckle gun 10. ^ Elisha Collier revolver 11. ^ "Elements of military art and history" By Edouard La Barre Duparcq, Nicolas douard Delabarre-Duparcq, 1863 12. ^ "Pistols: An Illustrated History of Their Impact" By Jeff Kinard, Published by ABC-CLIO, 2004 13. ^ Flayderman, 1998 14. ^ Flayderman, 1998 15. ^ Day of Concord and Lexington (French, 1925) p. 25 note 1. See also pp. 27-36. 16. ^ Flayderman, 1998 Flayderman's Guide to Antique Firearms and Their Values 7th Edition, by Norm Flayderman 1998 Krause Publications ISBN 0-87349-313-3, 9780873493130

External links

Exploded View of a Flintlock How Flintlock Guns Work Flintlocks in Wet Weather Flintlock FAQ 3D animation about how flintlock pistol works on YouTube.

Bibliogaphy
French flintlock & early firearms explained by Gerard Henrotin (HLebooks - 2012) Retrieved from "http://en.wikipedia.org/w/index.php?title=Flintlock&oldid=473582612"

You might also like