Professional Documents
Culture Documents
ML
Track rail
Interchangeable specication
Single slide unit Single track rail1 Assembled set
1
ML LWL ML
4
12
8
T1
9 10 11
P S1 /U P S1
C 12 C1 R200 B
C 12 C1 R200
T1
P S1 /U
Non-interchangeable specication
Slide unit Casing C-Lube Ball End plate End seal Ball retaining band Oil hole Linear Way L
Assembled set
ML
C 12 C1 R200 B
T1
/U
1 2 3 4
Structure
Size
Dimensions Page 7
LWL
5 6 7 8
Points
Extremely small size realized by simple structure For details
P. -19
Material type
Super small-size linear motion rolling guide produced by two-row four-point contact simple structure and original small sizing technology. The track rail width of LWL1, the smallest size, is only 1mm.
Preload amount
P. -41
The slide unit shape can be selected from two types, the standard type and the wide type suited for single-row track rail uses, and there are four types with different lengths of slide unit with same section. Furthermore, the track rail has the variation of standard type and tapped rail type with the screw thread implanted, allowing you to select an optimal product for the specications of your machine and device.
4 5
Stainless steel highly corrosion-resistant is used as the basic specication, so that the products are suitable for applications where rust prevention oil is not preferred, such as in cleanroom environment. High carbon steel products suited to general purposes are also provided.
P. -31
Accuracy class
C-Lube linear way L models for special environment uses are provided as a series. Increasingly varied special environment uses are supported, such as by high-speed / low-noise specications by combining silicon nitride ceramics and low dust-generation specications.
Note1Indicate "LWLB" or "LWLFB" for the model code of the single track rail regardless of the series and the combination of slide unit models.
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
Structure
Model MLC
LWLCB
Size 1
12 15 20 25
For applicable models and sizes, see Table 2.1 and Table 2.2. Indicate "LWLB" or "LWLFB" for the model code of the single track rail regardless of the series and the combination of slide unit models. Note1This model has no built-in C-Lube.
Standard
ML
LWLB
Long
MLG
LWLGB
Extra long
Structure
MLL
Standard
LWLBCS
Short
LWL
Ball nonretained type Ball retained type Ball nonretained type Ball retained type Ball retained type
Long
LWLGN
Standard
LWLY
For applicable models and sizes, see Table 2.1 and Table 2.2.
Size
Standard type 1, 2, 3, 5, 7, 9, 12, 15, 20, 25 Wide type 4, 6, 10, 14, 18, 24, 30, 42
C
For applicable models and sizes, see Table 2.1 and Table 2.2.
LWL
5 6 7
For an assembled set, indicates the number of slide units assembled on a track rail. For a single slide unit, only "C1" is specied. Indicate the length of track rail in mm. For standard and maximum lengths, see Table 3.1, Table 3.2, and Table 3.3.
Material type
No symbol For applicable models and sizes, see Table 2.1 and Stainless steel made High carbon steel made CS Table 2.2.
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
10
14
18
24
30
42
L E F L E LWL1Y
n (Pieces)
Short
Ball retained type Ball nonretained type Ball retained type Ball nonretained type
MLF
LWLFB LWLF
Standard
Long
MLFG
LWLFGB
LWL1
n (Pieces)
Standard
Ball retained type Ball retained type Ball nonretained type Ball retained type Ball nonretained type Ball retained type
LWLFBCS
E F L E
Short
LWLFCN
LWLFN
unit: mm Identication number Item ML 5 LWL 5B 60 4 90 6 105 7 120 8 15010 15 7.5 4 11.5 210 510 5 915 ML 25 LWL 25B 240 4 300 5 360 6 480 8 66011 90015 60 30 9 39 960 1 800 ML 7 LWL 7B 60 4 90 6 120 8 15010 18012 24016 15 7.5 4.5 12 300 990 7 1 905
Standard
LWL1Y 18 3 30 5 42 7
LWL1 18 30 42
LWL2 32 4 40 5 56 7 8010
Long
LWLFGN
Standard length Ln
102
Maximum number of butt-jointing track rail3 Maximum length of butt-jointing track rail3 Identication number Item
ML 12 LWL 12B 100 4 150 6 200 8 27511 35014 47519 25 12.5 5 17.5 1 000 1 450
ML 15 LWL 15B 160 4 240 6 320 8 44011 56014 68017 40 20 5.5 25.5 1 000 1 480
ML 20 LWL 20B 180 3 240 4 360 6 480 8 66011 84014 60 30 8 38 960 1 800
Standard length Ln
Maximum number of 2 2 2 2 2 butt-jointing track rail3 Maximum length of 1 660 1 925 1 880 1 740 1 740 butt-jointing track rail3 1 Notes Not applicable to track rail with stopper pins (supplemental code "/S"). 2Length up to the value in ( ) can be produced. If needed, please contact . Not applicable to tapped rail specications. 3Not applicable to interchangeable specications or tapped rail specications. Remarks 1. A typical identication number is indicated, but is applied to all models of the same size. 2. Indicate "LWLB" for the model code of the single track rail regardless of the series and the combination of slide unit models. 3. If not directed, E dimensions for both ends will be the same within the range of E reference dimensions. To change the dimensions, indicate the specied rail mounting hole positions "/E" of special specication. For more information, see page III-29.
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
10
F L
E LWLF 42B
F L
unit: mm Identication number Item MLF 10 LWLF10B 60 3 80 4 120 6 160 8 22011 28014 20 10 4.5 14.5 300 500 7 1 840 MLF 30 LWLF30B 160 4 240 6 320 8 44011 56014 68017 40 20 6.5 26.5 680 2 000 MLF 14 LWLF14B 90 3 120 4 150 5 180 6 240 8 30010 30 15 5.5 20.5 300 990 8 1 950 MLF 42 LWLF42B 160 4 240 6 320 8 44011 56014 68017 40 20 6.5 26.5 680 2 000 Item Identication number Item 80 4 160 8 22011 28014 38019 50025 60030 20 10 4.5 14.5 1 000 LWLF18BCS 100 4 200 8 27511 35014 47519 60024 70028 25 12.5 5 17.5 1 500 LWLF24BCS 160 4 320 8 44011 56014 68017 80020 92023 40 20 5.5 25.5 1 520 LWLF30BCS LWL 9BCS LWL12BCS LWL15BCS
unit: mm LWL20BCS 180 3 240 4 360 6 480 8 66011 90015 1 02017 60 30 8 38 1 560 LWLF42BCS
Standard length Ln
Standard length Ln
Pitch of mounting holes F E or higher E reference dimensions1 below Maximum length2 Maximum number of butt-jointing track rail3 Maximum length of butt-jointing track rail3 Identication number Item
Pitch of mounting holes F E or higher E reference dimensions1 below Maximum length Identication number
MLF 18 LWLF18B 90 3 120 4 150 5 180 6 240 8 30010 30 15 5.5 20.5 690 1 860
MLF 24 LWLF24B 120 3 160 4 240 6 320 8 40010 48012 40 20 6.5 26.5 680 1 960
Standard length Ln
90 3 120 3 160 4 160 4 180 6 240 6 320 8 320 8 240 8 320 8 44011 44011 Standard length Ln 30010 40010 56014 56014 42014 60015 68017 68017 51017 72018 80020 80020 60020 80020 92023 92023 Pitch of mounting holes F 30 40 40 40 E 15 20 20 20 or higher 5.5 6.5 6.5 6.5 E reference dimensions1 below 20.5 26.5 26.5 26.5 Maximum length 1 500 1 520 1 600 1 600 Note1Not applicable to track rail with stopper pins (supplemental code "/S"). Remarks 1. A typical identication number is indicated, but is applied to all models of the same size. 2. If not directed, E dimensions for both ends will be the same within the range of E reference dimensions. To change the dimensions, indicate the specied rail mounting hole positions "/E" of special specication. For more information, see page III-29.
Maximum number of 3 3 3 3 butt-jointing track rail3 Maximum length of 1 920 1 840 1 840 1 840 butt-jointing track rail3 Notes1Not applicable to track rail with stopper pins (supplemental code "/S"). 2Length up to the value in ( ) can be produced. If needed, please contact . Not applicable to tapped rail specications. 3Not applicable to interchangeable specications or tapped rail specications. Remarks 1. A typical identication number is indicated, but is applied to all models of the same size. 2. Indicate "LWLFB" for the model code of the single track rail regardless of the series and the combination of slide unit models. 3. If not directed, E dimensions for both ends will be the same within the range of E reference dimensions. To change the dimensions, indicate the specied rail mounting hole positions "/E" of special specication. For more information, see page III-29.
11
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
12
Preload Amount
Accuracy class
Preload amount
T0
Specify this item for an assembled set or a single slide No symbol unit. T1 For details of the preload amount, see Table 4. For applicable preload types, see Table 5.1 and Table 5.2.
Accuracy class
High Precision
H P
For interchangeable specication products, assemble a slide unit and a track rail of the same accuracy class. Size 1 series have "No symbols." For the details of accuracy class, see Table 6.1 and 6.2.
Very light motion Light and precise motion Almost no vibrations Load is evenly balanced Light and precise motion
H
H
0.02 C0
Notes1There is zero or subtle clearance. 2Indicates zero or minimal amount of preload. Remark: C0 indicates the basic static load rating.
A D1
N1 B
N2 D2
A D
N B
unit: mm
unit: mm
P Item 0.020 0.010 Dim. H tolerance 0.025 0.015 Dim. N tolerance 0.015 0.007 Dim. variation of H1 0.020 0.010 Dim. variation of N1 Dim. variation of H for 0.020 0.030 multiple assembled sets2 Parallelism in operation of the slide unit C surface to A See Fig. 1 surface Parallelism in operation of the slide unit D surface to B See Fig. 1 surface Notes1It means the size variation between slide units mounted on the same track rail. 2Applicable to the interchangeable specication.
Tolerance
0.020 0.025
Classclassication symbol
High
H
Precision
Light preload T1
1 1 1 1
Light preload T1
1 2 3 5 1 7 1 9 1 12 1 15 20 25 Note1Not applicable when /HB is specied. Remark: The mark indicates that interchangeable specication products are available.
4 6 10 14 18 24 30 42 Remark: The mark indicates that interchangeable specication products are available.
30
Parallelism m
20
Hig
10
Precis
ionP
500
1000
1500
2000
13
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
14
Special Specication
Table 7.4 Application of special specications (Non-interchangeable specication)
10
Interchangeable
This is specied for the interchangeable specications. S2 Assemble a track rail and a slide unit with the same No symbol interchangeable code. Performance and accuracy of "S1" and "S2" are the same. For applicable models and sizes, see Table 2.1 and Table 2.2. "No symbol" is indicated for non-interchangeable specication.
S1
2 4
3 6
5 7
5 10
7 14
6
9 18
6
12 24
6
15 30
6
20 42
25
11
Special specication
/A, /BS, /D, /E, /HB, /1, /LR, /MN, /N, /Q, /RE, /S, /U, /W, /Y
For applicable special specications, see Tables 7.1, 7.2, 7.3, and 7.4. For combination of multiple special specications, see Table 8. For details of special specication, see page -28.
Table 7.1 Application of special specications (Interchangeable specication, single slide unit)
Size Special specication No end seal With C-Lube plate1 Under seal Note1Applicable to LWW(F) series. Supplemental code /N /Q /U 1
2 4
3 6
5 10
7 14
9 18
12 24
15 30
20 42
25
2 Butt-jointing track rails1 /A 5 Stainless steel end plate3 /BS Opposite reference surfaces arrangement /D Specied rail mounting hole positions /E Hybrid C-Lube Linear Way /HB Inspection sheet /1 Black chrome surface treatment (track rail) /LR 7 Without track rail mounting bolt2 /MN No end seal /N With C-Lube plate3 /Q Special environment seal3 /RE Track rail with stopper pins /S Under seal /U A group of multiple assembled sets /W 8 Specied grease4 /Y 1 Notes Not applicable to high carbon steel made products. 2Not applicable to tapped rail specication. 3Applicable to LWL(F) series. / YCG is applicable to ML(F) series. 4ML(F) series is applicable only to /YCG. 5Not applicable to size 4 and 6 series. 6Applicable to size 7, 9, 12, and 15 of ML series. 7Not applicable to size 2 and 3 series. 8Applicable only to /YNG.
Table 7.2 Application of special specications (Interchangeable specication, single track rail)
Size Special specication Specied rail mounting hole positions Without track rail mounting bolt Supplemental code /E /MN 1
2 4
3 6
5 10
7 14
9 18
12 24
15 30
20 42
25
2 4
3 6
5 10
7 14
9 18
12 24
15 30
20 42
25
Opposite reference surfaces arrangement /D Specied rail mounting hole positions /E Without track rail mounting bolt1 /MN No end seal /N With C-Lube plate2 /Q Under seal /U Notes1Not applicable to tapped rail specication. 2Applicable to LWL(F) series.
LR MN N Q RE S U W Y
A BS D E HB 1 LR MN N Q RE S U W Remarks 1. The combination of " " shown in the table is not available. 2. When using multiple types for combination, please indicate by arranging the symbols in alphabetical order.
15
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
16
Special Specication
Table 9 Dimensions of slide unit with C-Lube plate (Supplemental code /Q)
L4 C-Lube L1 C-Lube
Lubrication
Table 11 Dimensions of track rail with stopper pins (Supplemental code /S)
a
Dust Protection
The slide unit of ML(F) series and LWL(F) series is dust protected by end seals included as standard. However, if large amount of contaminant or dust are oating, or if large particles of foreign substances such as chips or sand may adhere to the track rail, it is recommended to attach a protective cover to the linear motion mechanism. No end seal is provided for size 1, 2, 3, 4 or 6 series. For applications in the environment not clean enough, cover the entire unit with a protective case, etc. to prevent harmful foreign substances such as dust and particles from outside to enter.
LWLC 5B 22 LWLFC 10B 26.5 LWL 5B 25 LWLF 10B 30.5 LWLC 7B 27 LWLFC 14B 30.5 LWL 7B 31.5 LWLF 14B 39.5 LWLG 7B 39 LWLFG 14B 50 LWLC 9B 30 LWLFC 18B 34.5 LWL 9B 39 LWLF 18B 46.5 LWLG 9B 49 LWLFG 18B 58.5 LWLC 12B 33 LWLFC 24B 38.5 LWL 12B 42 LWLF 24B 52 LWLG 12B 52 LWLFG 24B 67 LWLC 15B 42 47 LWLFC 30B 45.5 50 LWL 15B 52 57 LWLF 30B 59.5 64 LWLG 15B 67 72 LWLFG 30B 78.5 83 LWLC 20B 48 53 LWLFC 42B 51.5 56 LWL 20B 60 65 LWLF 42B 65 70 LWLG 20B 78 83 LWLFG 42B 84.5 89 LWLC 25B 63.5 74 LWL 25B 87.5 98 LWLG 25B 107.5 117 Remarks 1. The dimensions of the slide unit with C-Lube at both ends are indicated. 2. A typical identification number is indicated, but is applied to all LWL(F) series models of the same size.
Lithium-soap base grease (MULTEMP PS No.2 [KYODO YUSHI CO., LTD.]) is pre-packed in ML(F) and LWL(F) series. Additionally, ML(F) series has C-Lube placed in the recirculation part of balls, so that lubricant replenishment interval can be extended and maintenance man-hours such as grease job can be reduced signicantly. ML(F) series and LWL(F) series have grease nipple or oil hole as indicated in Table 14. Since the Size 1, 2, 3, 4 and 6 series do not have an oil hole, apply grease directly to the raceway part of the track rail for re-greasing. Supply nozzles t to each shapes of grease nipple and dedicated supplying equipment (miniature greasers) fit to oil holes are also available. When these parts are desired, refer to Table 14 and Table 15.1 in -22 and Table 16 of page -23 to order.
10
12
14
2.5
15
24
25
3.5 2.5
30 42
d2
20
d1
18
End plate
unit: mm
Size 5 7 9 12 10 14 18 24
d1
0.5
H1
Table 10 Load rating / static moment rating (Supplemental code /HB) of Hybrid C-Lube Linear Way
TX N m 1.6 937 965 3.5 MLC 7/HB 12.6 4.0 1 330 1 610 5.9 ML 7/HB 23.9 7.5 MLG 7/HB 1 690 2 250 8.2 43.1 2.4 MLC 9/HB 1 180 1 260 5.9 18.2 7.7 ML 9/HB 1 810 2 340 10.9 43.4 15.9 MLG 9/HB 2 370 3 420 15.9 83.6 27.1 2 870 4 500 20.9 MLL 9/HB 134 4.5 2 210 2 030 12.6 MLC 12/HB 35.5 13.1 3 330 3 650 22.6 ML 12/HB 79.2 26.0 4 310 5 270 32.7 MLG 12/HB 143 59.3 MLL 12/HB 5 820 8 110 50.3 288 9.9 MLC 15/HB 3 490 3 310 25.5 71.8 25.3 ML 15/HB 4 980 5 520 42.5 146 54.3 6 620 8 280 63.7 MLG 15/HB 288 104 8 370 11 600 89.2 MLL 15/HB 497 Note1The upper values of TX and TY are for one slide unit lower values are for two slide units sticking. Identication number C N C0 N T0 N m
1
Applicable supply nozzle type Miniature greaser A-5120VA-5240V B-5120VB-5240V A-8120V B-8120V
TY N m 1.3 10.6 3.3 20.1 6.3 36.2 2.1 15.3 6.5 36.4 13.4 70.1 22.7 112 3.8 29.8 11.0 66.4 21.9 120 49.8 242 8.3 60.3 21.2 122 45.5 241 86.9 417 and the
1 2 3 18 2 20 4 24 2 1 25 5 30 2 42 3 Note1The dimensions are the same as those before mounting of under seal.
M4
17
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
18
Mounting screws for slide unit To mount a slide unit, tightly fasten the bolt against female thread of slide unit. The female thread is created through holes of the slide unit for size 1 series, and also through holes for the slide unit and track rail for size 2, 3, 4 and 6 series. When the xing thread depth of the mounting screw goes too deep, it can interfere with the track rail and impact the running accuracy or product life so that the fixing thread depth should be within the screwing depth specied in the dimension table. Also prepare the small screws dedicated to precision devices (head diameter 1.8 mm or smaller) for the mounting bolt of slide unit of size 1. Mounting screws for track rail In the size 2 and 3 series and tapped rail specifications, track rail mounting bolts are not appended. Prepare mounting bolts whose xing thread depth is less than H4 in dimension table. Shoulder height and corner radius of the reference
general mounting structure When mounting the ML(F) series and LWL(F) series, properly align the reference mounting surfaces B and D (D1 or D2)of the track rail and slide unit with the reference mounting surface of the table and bed before xing them. (See Fig. 2) Reference mounting surfaces B and D (D1 or D2) and mounting surfaces A and C are precisely ground. By machining the mounting surface of the mating member, such as machine or device, to high accuracy and mounting them properly, stable linear motion with high accuracy is obtained. Reference mounting surface of the slide unit of size 2 or mark. The track rail higher is the opposite side of the reference mounting surface is identified by locating the mark on the top surface of the track rail. It is the side surface above the mark (in the direction of the arrow). (See Fig. 5.2) Reference mounting surface of the slide unit of size 1 is located at both right and left sides (D1 and D2). (See Fig. 5.1) The track rail of LWL1Y has the mounting structure of lateral direction. Two types of mounting structure as shown in Fig. 3.1 and Fig. 3.2 are available.
D1 C
A B
Fig. 3.2 Reference mounting surface of LWL1Y and typical mounting structure
M1 0.25 0.04 M1.40.3 0.10 M1.60.35 0.15 M2 0.4 0.31 M2.50.45 0.62 M3 0.5 1.1 1.2 M4 0.7 2.5 2.8 M5 0.8 5.0 5.6 M6 1 8.5 Remarks 1. The calculation is based on the tightening torque, strength division 8.8 and property division A2-70. 2. It is recommended that the tightening torque of slide unit mounting holes for series size 1 is to be 70 to 80 % of the values in the table.
mounting surface For the opposite corner of the mating reference mounting, it is recommended to have relieved llet as indicated in Fig. 6 Recommended value for the shoulder height on the mating side is indicated in Table 16.
Fig. 4 Reference mounting surface of size 2, 3, 4 and 6 series and typical mounting structure
A B
Track rail
Slide unit
D1
D2
Track rail
Tightening torque for mounting bolts Typical tightening torques for mounting ML(F) series and LWL(F) series to the steel mating member material are indicated in Table 15. When vibration and shock of the machine or device are large, fluctuating load is large, or moment load is applied, x it by using the torque 1.2 to 1.5 times larger than the value indicated in the table as necessary. If the mating member material is cast iron or aluminum, reduce the tightening torque depending on the strength characteristic of the mating member material.
D A B
Fig. 3.1 Reference mounting surface of LWL1Y and typical mounting structure
Mark Mark
19
20
Mounting Bolt
For LWL(F) series, track rail mounting bolt of slide unit and tapped rail specication shown in Table 17 and Table 18are . available. If these parts are necessary, please contact
h2
h1
R2
Mounting part of track rail
Mounting part of track rail Shoulder height1 h2 Corner radius R2Maximum unit: mm Bolt size
d
Shoulder height h1
LWL 1Y 2 1.3 LWL 1 LWL 2 1 0.1 0.5 0.05 LWL 3 1.2 0.15 0.8 0.1 ML 5 LWL 5B 2 0.3 0.8 0.2 ML 7 LWL 7B 2.5 0.2 1.2 0.2 ML 9 LWL 9B 0.2 3 1.5 0.2 LWL 9BCS 0.4 ML 12 LWL 12B 0.2 4 2.5 0.2 LWL 12BCS 0.4 ML 15 LWL 15B 0.2 4.5 3 0.2 LWL 15BCS 0.4 ML 20 LWL 20B 0.2 5 4 0.2 LWL 20BCS 0.4 ML 25 LWL 25B 6.5 0.7 4 0.7 LWLF 4 1.5 0.1 0.8 0.1 LWLF 6 2 0.1 0.8 0.1 MLF 10 LWLF 10B 2 0.3 1.2 0.2 MLF 14 LWLF 14B 2.5 0.2 1.2 0.2 MLF 18 LWLF 18B 0.2 3 2.5 0.2 LWLF 18BCS 0.4 MLF 24 LWLF 24B 0.2 4 2.5 0.2 LWLF 24BCS 0.4 MLF 30 LWLF 30B 0.2 4.5 2.5 0.2 LWLF 30BCS 0.4 MLF 42 LWLF 42B 0.2 5 3 0.2 LWLF 42BCS 0.4 Note1For models with under seals (supplemental code "/U"), it is recommended to use the values 1mm smaller than the values in the table. However for the models of size 9 with under seal, 0.8 mm is recommended. Remark: A typical identication number is indicated, but is applied to all models of the same size.
Pitch of screw P
dk
M1 0.25 1.8 0.45 3, 4, 5 1 M1.4 0.3 2.5 0.8 2.5, 3, 4 1 M1.6 0.35 2.8 0.85 4, 5, 6 1 M2 0.4 3.5 1 3, 4, 5 Note1Based on cross-recessed head screw for precision equipment (Number 0) in Japan Camera Industry Standard JCIS 10-70. Remark: The dimensions are different from the appended track rail mounting bolts.
dk
unit: mm Bolt size d Pitch of screw P dk k s 1.3 1.5 1.5 t 0.6 0.7 1 l 2.5, 3, 4 4, 5, 6 3, 4, 5
M1.4 0.3 2.6 1.4 1 M1.6 0.35 3 1.6 1 M2 0.4 3.8 2 Note1Based on hexagon socket head bolts equivalent to JIS B 1176.
21
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
22
L3 L2
2M1depth
L1
L3 W2 M2 L2
2M1depth
Shape
H
H4
H1
LWL 1Y
M2
H5
H1
Size
1 9
2 3 5 7 12 15 20 25
d3
F
L L1
1
H4
F L
1
L3 W2 H2 L2
2M1depth
H1
H4
LWL 1
N W
L 1
Interchangeable
Identication number
LWL series
No C-Lube
Mass (Ref.) g
Dimensions of assembly mm H 4.2 2.5 3.2 4 H1 2.2 0.5 0.7 1 2 2.5 6 8 12.5 11.5 15.5 N W2 L1
Appended mounting Basic dynamic Basic static 5 bolt for track rail2 load rating5 load rating mm E 3
ML series
Slide Track rail unit per 100 mm 2.1 1.0 0.9 1.0 1.6 2.8 5.3
L2
L3
M1depth
H2
H4 3.1 1.4
H5 1.1
M2 M1.4 Through
d3 1.1
F 6
C N 66.8
C0 N 113
T0 Nm 0.06
TX Nm
0.07 0.47 0.54 2.9 0.39 2.7 0.98 5.6
TY Nm
0.09 0.56 0.64 3.5 0.47 3.2 1.2 6.7
1 Y 1 2
0.16
1.5
6.5
3.9
M1 0.9
1.2
4 3.5 5.5
2 3
2 2.6
4 5
8 10
LWLC 3 LWL 3
Notes
Track rail lengths L are shown in Table 3.1 on page -10. 2Track rail mounting bolts are not appended. 3Prepare screws according to mounting structure. 4Choose screws whose dimension allow xing thread depth into track rail R to be less than H4. 5The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the
sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. Remarks 1. Metal parts are made of stainless steel. 2. Do not disassemble a slide unit from the track rail because steel balls are not retained. No end seal is attached. 3. The specication of small size mounting bolts (M2 and less) are show on page -22. If needed, please contact
LWL
1 2
2
3
C2
4
R80
5 1
T0
6
P
7
/D
8
C C0
TY T0 TX
Size
1, 2, 3
Preload amount
T0 Clearance
Special specication
BS, D, E, 1, MN, W, Y
Standard type
4
Accuracy class
No symbol H P Ordinary High Precision
C No symbol
23
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
24
2M1depth d4 M2
L3
L3 L2
4M1depth
H1
H4
Size
1 9
2 3 5 7 12 15 20 25
H3
W
Tapped rail specication LWLN
Interchangeable
Identication number
LWL series
No C-Lube
Mass (Ref.) g
Dimensions of assembly mm H H1 N W2 W3
Appended mounting bolt Basic dynamic Basic static 4 load rating4 load rating for track rail2 mm E F Bolt sizeR Cross-recessed head screw for precision equipment M26 M2.5R3 Not appended Cross-recessed head screw for precision equipment M26 M2.5R3 Not appended Hexagon socket head bolt M26 M3R3 Not appended Hexagon socket head bolt M26 M3R3
Not appended
ML series
W4
L1
L2
L3
M1depth
H3
H4
M2
d3
d4
C N
C0 N
T0 Nm
TX Nm
TY Nm
MLC 5
LWLC 5B
12 3.4 16 13 4.3 12 4.4 19 13 6.7 7.1 9.1 10 13 14 22 19 24 22 8 24 22 31 24 12 21.6 1.5 5 17 12 2.5 23.5 8 14.3 M22.5 1.5 7 5
2.4
3.6
0.8
562
841
2.2
1.4 8.5
1.2 7.2
LWLC 5N*
ML
5
LWL 5B
3.5
12
M21.5
1.2
3.7
15
676
1 090
2.9
2.3 12.8
1.9 10.8
LWL
5N*
MLC 7
LWLC 7B
2.4
4.2
2.3
9.6 M3 Through
937
1 140
4.1
1.8 14.9
1.5 12.5
LWLC 7N*
ML
7
LWL 7B 7N*
2.4
4.2
2.3 7.5 15
1 330
1 890
6.9
LWL
M3 Through
4.7 28.2
3.9 23.6
MLG 7
LWLG 7B
2.4
4.2
2.3
1 690
2 650
9.7
LWLG 7N*
M3 Through
8.8 50.7
7.4 42.5
Notes1Track rail lengths L are shown in Table 3.1 on page -10. 2The appended track rail mounting bolts are hexagon socket head bolts equivalent to JIS B 1176 or cross recessed head screws for precision equipment. 3Choose screws whose dimension allow xing thread depth into track rail R to be less than H4. 4The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. If hybrid C-Lube Linear Way specication (supplemental code "/HB") is selected in MLC7, ML7, and MLG7, see Table 10 on page -17. Remarks 1. The specication of oil hole is shown in Table 13 on page -18. 2. The identication numbers with * are our semi-standard items.
C C0 TY T0 TX
ML
1
C
2
7
4
C2 R120
5 6 1
T1
7
P
8
S1
9
/D
10
Size
5, 7
Preload amount
T0 No symbol T1 Clearance Standard Light preload
Interchangeable
S1 specication S2 specication Non-interchangeable specication
Standard type
5
S1 S2 No symbol
C No symbol G
Accuracy class
H P High Precision
10
Special specication
25
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
26
4M1depth
L1
L3
L3 L2 L2/2
L3 L2 L2/2
6M1depth
d4 M2
H4
Size
1 9
2 3 5 7 12 15 20 25
H3
H1
d3 N W
Tapped rail specication LWLN
MLC LWLC
MLL
Interchangeable
Identication number
LWL series
No C-Lube
Mass (Ref.) g
Dimensions of assembly mm H H1 N W2 W3
Appended mounting bolt for track rail2 mm E F Bolt sizeR M38 M4R3 Not appended
Basic dynamic Basic static 4 load rating4 load rating C N 1 180 C0 N 1 480
ML series MLC
W4
L1
L2
L3
M1depth
H3
H4
M2
d3 3.5
d4 6
h 3.5
T0 Nm 6.9
TX Nm
2.9 21.4
TY Nm
2.4 18.0
LWLC LWLC
9B 9N*
21.5
11.9
M4 Through
ML
9
LWL 9B 9BCS 9N*
3.5
3.5 10 20
LWL LWL
30 10 2 5.5 20 15 2.5
10
M4R3 Not appended M38 2 370 4 030 18.7 M4R3 Not appended M38 2 870 2 210 5 300 2 380 24.6 14.8
18.7 98.3 15.7 82.5
MLG
9
LWLG 9B 9N*
3.5
3.5
40.5 37 35 50 25
15
30.9 M4 Through
LWLG
MLL
26
40.4 13
3.5
3.5
MLC 12 ML 12
LWLC 12B
LWL
12B 12BCS
15
4 290
26.6
LWL
MLG 12
LWLG 12B
20 30
32 47.3
6 200 9 540
38.4 59.1
MLL 12 Notes
1
Track rail lengths L are shown in Table 3.1 on page -10 and Table 3.3 on page -12. 2The appended track rail mounting bolts are hexagon socket head bolts equivalent to JIS B 1176. For stainless steel model, stainless steel made bolts are appended.
3Choose screws whose dimension allow xing thread depth into track rail R to be less than H4. 4The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the
sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. If hybrid C-Lube Linear Way specication (supplemental code "/HB") is selected in ML series, see Table 10 on page -17. Remarks 1. The specication of oil hole is shown in Table 13 on page -18. 2. The identication numbers with * are our semi-standard items.
1
ML
1
G
2
9
3
C2 R160
4 5 1 6
T1
7
P
8
S1
9
/D
10
C C0
TY T0 TX
Size
9, 12
Preload amount
T0 No symbol T1 Clearance Standard Light preload
Interchangeable
S1 specication S2 specication Non-interchangeable specication
Standard type
4 5 6
S1 S2 No symbol
10
Special specication
C No symbol G L
Material type
Accuracy class
H P High Precision
27
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
28
4M1depth
L 4 L1
Shape
W2 W4 W3
Grease nipple4
2M1depth d4
L1
6M1depth
L3 H3
L3 L2 L2/2
L3 L2 L 2 /2
Size
1 9
2 3 5 7 12 15 20 25
H4
Interchangeable
Identication number
LWL series
No C-Lube
Mass (Ref.) g
Dimensions of assembly mm H H1 N W2 W3 W4 L1 32 L2
Appended mounting bolt Basic dynamic Basic static 3 load rating 3 for track rail2 load rating mm E F Bolt sizeR C N 3 490 C0 N 3 890
ML series MLC 15
Slide Track rail unit per 100 mm 43 42 63 64 93 95 122 89 130 133 189 196 189 190 305 310 405 413 243 156 107
L4 37
M1depth
H3
H4
d3
d4
T0 Nm 30.0
TX Nm
11.7 84.5
TY Nm
9.8 70.9
LWLC 15B
ML
15
LWL 15B 15BCS
LWL
16
8.5
32
25
3.5
42
20
47
M34
3.1
15
10
3.5
6.5
4.5
20
40
M310
4 980
6 490
50.0
29.7 172
24.9 144
MLG 15
LWLG 15B
57 72 38
25 40
62 76 43
MLL 15 MLC 20 ML 20
LWL
LWLC 20B
20B 20BCS
LWL
20
10
40
30
50
25
34.6
55
M46
4.2
20
11
9.5
5.5
30
60
M514
6 650
9 080
92.6
MLG 20
LWLG 20B
68
30
52.3
73
8 510
12 900
131
MLC 25
LWLC 25B
54.5
31.9
64
9 120
10 600
128
ML
25
LWL 25B
25
12.5
48
35
6.5
78
35
55.7
88
M67
23
15
11.0
9.0
30
60
M616
13 500
18 500
223
MLG 25
LWLG 25B
98
40
75.5 108
16 700
25 200
303
Notes1Track rail lengths L are shown in Table 3.1 on page -10 and Table 3.3 on page -12. 2The appended track rail mounting bolts are hexagon socket head bolts equivalent to JIS B 1176. For stainless steel model, stainless steel made bolts are appended. 3The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. If hybrid C-Lube Linear Way specication (supplemental code "/HB") is selected in MLC15, ML15, MLG15, and MLL15, see Table 10 on page -17. 4The shapes of grease nipple vary by size. The specications are shown in Table 14 on page 18.
TY T0 TX
ML
1
G
2
15
3
C2 R320
4 5 1 6
T1
7
P
8
S1
9
/D
10
Model ML LWLB
Size
15, 20, 25
Preload amount
T0 No symbol T1 Clearance Standard Light preload
Interchangeable
S1 specication S2 specication Non-interchangeable specication
Standard type
4
C C0
S1 S2 No symbol
10
5 6
Special specication
C No symbol G L
Material type
Accuracy class
H P High Precision
29
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
30
Shape
W4
W2 W3
Oil hole5
2M1depth d4 M2
L3
L3 L2
2M1depth
Size
H1
H4
4 18
6 24
10 30
14 42
H3
Interchangeable
Identication number
LWLF series
No C-Lube
Mass (Ref.) g
Dimensions of assembly mm H1 N W2 W3
Appended mounting bolt Basic dynamic Basic static 4 load rating4 load rating for track rail mm E F Bolt sizeR Cross-recessed head screw for precision equipment M1.65 Cross-recessed head screw for precision equipment M24 M3R3 Not appended Cross-recessed head screw for precision equipment M24 M3
R3 Not appended
MLF series
W4
L1
L2
L3
M1depth
H3
H4
M2
d3
d4
C N 390
C0 N 677
T0 Nm 1.4
TX Nm
1.3 7.1
TY Nm
1.5 8.4
LWLF
2 4
10
17
6.5
11.9 M2 1.3
2.6
1.8
2.8
0.75
10
LWLFC
2 6
13 2.4 15 12 4.5 1 3 12
2.4
1.5
4.5
9.8 M2 1.6
334
542
1.7
0.84 5.1
1.0 6.1
LWLFC
6 N *
6 20 8 14.6
2.8
M3 Through
7.5 2.4
15
LWLF
13 3.4 12 6.1 28 5.9 20.5 29 7.6 28 7.5 24.5 29 17.6 6.5 1.5 3.5 17 13 2
1.5
443
813
2.5
1.8 9.9
2.2 11.8
LWLF
2 6 N *
M3 Through
MLFC 10
LWLFC 10B
2.9
4.8
1.6
712
1 180
6.1
2.6 14.9
2.2 12.5
LWLFC 10N*
MLF
10
LWLF 10B 10N*
2.9
4.8
1.6
Cross-recessed head screw for precision equipment M2.57 M3R3 Not appended
849
1 510
7.8
4.2 22.4
3.5 18.8
LWLF
M3 Through
Notes
Track rail lengths L are shown in Table 3.2 on page -11. 2Size 4 and 6 are non-retained-ball type. No end seal is attached. 3Choose screws whose dimension allow xing thread depth into track rail R to be less than H4. 4The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the
sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. 5No oil hole is prepared for size 4 and 6. The specication of oil hole for size 10 is shown in Table 13 on page -18. Remark: The identication numbers with * are our semi-standard items.
MLF C
1 2
10
3
C2 R120
4 5 1
T0
6
P
7
S1
8
/D
9
C0
TY T0 TX
Size
4, 6, 10
Preload amount
T0 No symbol Clearance Standard
Interchangeable
S1 specication S2 specication Non-interchangeable specication
S1 S2 No symbol
Accuracy class
H P High Precision
Special specication
A, BS, D, E, 1, MN, N, Q RE, S, W, Y
C No symbol
31
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
32
Shape
W4
W2 W3
Oil hole
2M1depth d4 M2
L3
L3 L2
4M1depth
Size
H1
H4
4 18
6 24
10 30
14 42
H3
Interchangeable
Identication number
Mass (Ref.) g
Dimensions of assembly mm H1 N W2 W3
Appended mounting bolt Basic dynamic Basic static 4 load rating4 load rating for track rail2 mm E F Bolt sizeR M38 M4R3 Not appended M38 15 30 1 770 M4R3 Not appended M38 2 320 4 160 2 840 1 240 1 700 C N C0 N
LWLF series
No C-Lube
T0 Nm 12.2
TX Nm 3.8 24.6
TY Nm 3.2 20.7
W4
L1
L2
L3
M1depth
H3
H4
M2
d3 3.5
d4 6
h 3.2
22.5
13
M4 Through
MLF
14
LWLF 14B 14N*
3.5
3.2
LWLF
5.5
25
19
31.5
10
22
M33
1.7
14
5.5
20.3
M4 Through
10.1 54.7
8.4 45.9
MLFG 14
LWLFG 14B
3.5
3.2
42 56
19
32.5 M4 Through M4
R3 Not appended
29.8
21.0 104
17.6 87.6
LWLFG 14N*
Notes1Track rail lengths L are shown in Table 3.2 on page -11. 2The appended track rail mounting bolts are hexagon socket head bolts equivalent to JIS B 1176. 3Choose screws whose dimension allow xing thread depth into track rail R to be less than H4. 4The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. Remarks 1. The specication of oil hole is shown in Table 13 on page -18. 2. The identication numbers with * are our semi-standard items.
MLF G
1 2
14
3
C2 R240
4 5 1
T1
6
P
7
S1
8
/D
9
C0
TY T0 TX
Size
14
Preload amount
T0 No symbol T1 Clearance Standard Light preload
Interchangeable
Wide type
4 5
Accuracy class
H P High Precision
Special specication
A, BS, D, E, 1, LR, MN N, Q, RE, S, W, Y
C No symbol G
33
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
34
Shape
W4
W2 W3
Oil hole
2M1depth d4 M2
L3
L3 L2
4M1depth
Size
H1
H4
4 18
6 24
10 30
14 42
H3
W
Tapped rail specication LWLFN
Interchangeable
Identication number
LWLF series
No C-Lube
Mass (Ref.) g
Dimensions of assembly mm H1 N W2 W3
Appended mounting bolt Basic dynamic Basic static 4 load rating4 load rating for track rail2 mm E F Bolt sizeR M38 M4R3 Not appended 1 510 2 120 C N C0 N
W4
L1
L2
L3
M1depth
H3
H4
M2
d3 3.5
d4 6.5
h 4.5
T0 Nm 19.4
TX Nm
5.5 35.9
TY Nm
4.7 30.1
26.5
16.6
M4 Through
MLF
18
LWLF 18B 18BCS 18N*
21 3 6 30
3.5
6.5
4.5 15 30
M38 2 280 M4R3 Not appended M38 2 870 5 300 48.5 M4R3 Not appended 2 800 3 340 40.7
31.9 159 26.7 134
LWLF LWLF
3 810
34.9
16.9 88.8
14.2 74.5
M4 Through
MLFG 18
LWLFG 18B
3.5
6.5
4.5
23 92
3.5
50.5
24
40.4 M4 Through
LWLFG 18N*
MLFC 24
LWLFC 24B
30.5
17.7
9.7 67.6
8.2 56.8
MLF
24
LWLF 24B 24BCS
40
28
44
15
31
M33.5
3.2
24
4.5
4.5
20
40
M410
4 310
6 200
75.6
30.6 168
25.7 141
LWLF
MLFG 24
LWLFG 24B
59
28
46.3
5 620
9 060
111
63.3 321
53.1 270
Notes1Track rail lengths L are shown in Table 3.2 on page -11 and Table 3.3 on page -12. 2The appended track rail mounting bolts are hexagon socket head bolts equivalent to JIS B 1176. For stainless steel model, stainless steel made bolts are appended. 3Choose screws whose dimension allow xing thread depth into track rail R to be less than H4. 4The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. Remarks 1. The specication of oil hole is shown in Table 13 on page -18. 2. The identication numbers with * are our semi-standard items.
MLF G
1 2
18
3
C2 R300
4 5 1 6
T1
7
P
8
S1
9
/D
10
C0
TY T0 TX
Size
18, 24
Preload amount
T0 No symbol T1 Clearance Standard Light preload
Interchangeable
S1 specication S2 specication Non-interchangeable specication
Wide type
4 5
S1 S2 No symbol
10
Accuracy class
H P High Precision
Special specication
A, BS, D, E, 1, LR, MN N, Q, RE, S, U, W, Y
C No symbol G
35
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
36
4M1depth
Shape 4 18 6 24 10 30 14 42
W2 W4 W3
Grease nipple
W2 W4 W3
Grease nipple
L3 d4
L3 L2
H3
H1
H1
W6 N
W5 W E
H4
Size
H3
Interchangeable
Identication number
LWLF series
No C-Lube
Mass (Ref.) g
Basic dynamic Basic static 3 load rating3 load rating C N 3 890 C0 N 4 540
Slide Track rail H unit per 100 mm 70 111 112 167 170 198 15
L3 20.5
L4 40
M1depth
H3
H4
W5
W6
d3
d4
T0 Nm 69.1
TX Nm 15.4 107 48.7 256 100 508 30.8 180 24.8 164 61.3 333 140 674 126 644
TY Nm 13.0 89.9 40.8 215 84.3 426 25.8 151 20.8 137 51.4 280 117 565 106 541
LWLFC 30B
LWLF
30B 30BCS
10
50
35
7.5
49.5
18
34.8
54
M44.5
3.1
30
4.5
4.5
20
40
M412
5 970
8 440
128
LWLF
MLFG 30
LWLFG 30B
68.5
35
53.8 25.7
73
7 810 5 440
MLFC 42
LWLFC 42B
95
LWLF 42B 42BCS
41.5
46 25.3 5 030
MLF
42
39.4 39 58.7 79 58.3 9 200 14 400 305 60 M44.5 3.2 42 10 23 9.5 4.5 8 4.5 20 40 M412 7 050 9 840 209
LWLF
MLFG 42
LWLFG 42B
9 520
15 100
321
Notes1Track rail lengths L are shown in Table 3.2 on page -11 and Table 3.3 on page -12. 2The appended track rail mounting bolts are hexagon socket head bolts equivalent to JIS B 1176. For stainless steel model, stainless steel made bolts are appended. 3The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the sketches below. The upper values of TX and TY are for one slide unit and the lower values are for two slide units sticking. Remark: The specications of grease nipple are shown in Table 14 on page 18.
MLF G
1 2
42
3
C2 R320
4 5 1 6
T1
7
P
8
S1
9
/D
10
C0
TY T0 TX
Size
30, 42
Preload amount
T0 No symbol T1 Clearance Standard Light preload
Interchangeable
S1 specication S2 specication Non-interchangeable specication
Wide type
4 5
S1 S2 No symbol
Accuracy class
H P High Precision
10
Special specication
A, BS, D, E, 1, LR, MN N, Q, RE, S, U, W, Y
C No symbol G
Material type
37
1N=0.102kgf=0.2248lbs. 1mm=0.03937inch
38