Professional Documents
Culture Documents
HDA-P
HDA-PR
HDA-PF
Anchor for presetting
HDA-T
HDA-TR
HDA-TF
Anchor for
through-fasting
Concrete
Tensile
zone
Nuclear
power plant
approval
European
Technical
Approval
of a headed
stud
Small edge
distance
and spacing
CE
conformity
Hilti anchor
design
software
Performance
Fire
resistance
Fatigue
Shock
Seismic
Corrosion
resistance
Approvals / certificates
Description
European technical approval a)
ICC-ES report
Shockproof fastenings in civil
defence installations
Nuclear power plants
Dynamic loads
Fire test report
Assessment report (fire)
Authority / Laboratory
CSTB, Paris
ICC evaluation service
DIBt, Berlin
DIBt, Berlin
IBMB, Braunschweig
warringtonfire
Z-21.1-1696 / 2008-09-01
Z-21.1-1693 / 2007-05-25
UB 3039/8151-CM / 2001-01-31
WF 166402 / 2007-10-26
a) All data for HDA-P(R) and HDA-T(R) given in this section according ETA-99/0009, issue 2008-03-25.
Sherardized versions HDA-PF and HDA-TF anchors are not covered by the approvals.
80
6 / 2010
Non-cracked concrete
M10
M12
M16
M20 a)
M10
M12
M16
M20 a)
[kN]
48,7
70,9
133,3
203,2
29,4
41,1
88,1
111,6
[kN]
48,7
70,9
133,3
203,2
29,4
41,1
88,1
111,6
[kN]
23,3
31,7
65,6
97,4
23,3
31,7
65,6
97,4
[kN]
24,3
36,0
66,7
24,3
36,0
66,7
[kN]
68,8
84,7
148,2
216,9
68,8
84,7
148,2
216,9
Anchor size
Tensile NRu,m
HDA-P(F), HDA-T(F)
b)
HDA-PR, HDA-TR
Shear VRu,m
HDA-P, HDA-PF
b)
HDA-PR
HDA-T, HDA-TF
b) c)
c)
75,1
92,1
160,9
75,1
92,1
160,9
HDA-TR
[kN]
a) HDA M20: only a galvanized 5m version is available
b) HDA-PF and HDA-TF anchors are not covered by ETA-99/0009
c) Values are valid for minimum thickness of the base plate tfix,min without use of centering washer (see setting
details)
Characteristic resistance
Non-cracked concrete
Cracked concrete
M10
M12
M16
M20 a)
M10
M12
M16
M20 a)
[kN]
46
67
126
192
25
35
75
95
[kN]
46
67
126
25
35
75
Anchor size
Tensile NRk
HDA-P(F), HDA-T(F)
HDA-PR, HDA-TR
b)
M10
M12
M16
M20 a)
22
30
62
92
23
34
63
Shear VRk
HDA-P, HDA-PF b)
[kN]
HDA-PR
for tfix
HDA-T, HDA-TF b)
[mm]
[mm]
10 15
<15 20
10
<15
15
<20
20
50
[kN]
65 c)
80 c)
80
100 140 c) 140 155 170 190 205 c) 205 235 250
[mm]
[mm]
10 15 10 15 20 30
<15 20 <15 <20 <30 50
65
15 20 25 30 35 20 25 40 55
<20 <25 <30 <35 60 <25 <40 <55 100
20
<25
25
<30
30
<35
35
60
HDA-TR
[kN]
71 c) 71 87 c) 87 94 109 152 c)
a) HDA M20: only a galvanized 5m version is available
b) HDA-PF and HDA-TF anchors are not covered by ETA-99/0009
c) With use of centering washer (t = 5 mm) only
152
158
170
for tfix
6 / 2010
81
Design resistance
Cracked concrete
Non-cracked concrete
Anchor size
M10
M12
M16
M20
a)
M10
M12
M16
M20 a)
Tensile NRd
HDA-P(F), HDA-T(F) b)
[kN]
30,7
44,7
84,0
128,0
16,7
23,3
50,0
63,3
HDA-PR, HDA-TR
[kN]
28,8
41,9
78,8
16,7
23,3
50,0
M10
M12
M16
M20 a)
17,6
24,0
49,6
73,6
17,3
25,6
47,4
Shear VRd
HDA-P, HDA-PF b)
[kN]
HDA-PR
[mm]
[mm]
10 15
<15 20
10
<15
15
<20
20
50
15 20 25 30 35 20 25 40 55
<20 <25 <30 <35 60 <25 <40 <55 100
[kN]
43 c)
53 c)
53
67
93 c)
[mm]
[mm]
10 15 10 15 20 30
<15 20 <15 <20 <30 50
20
<25
25
<30
30
<35
35
60
HDA-TR
[kN]
53 c) 53 65 c) 65 71 82
a) HDA M20: only a galvanized 5m version is available
b) HDA-PF and HDA-TF anchors are not covered by ETA-99/0009
c) With use of centering washer (t = 5 mm) only
114 c)
114
119
128
for tfix
HDA-T, HDA-TF
b)
for tfix
43
93
Recommended loads
Cracked concrete
Non-cracked concrete
Anchor size
Tensile NRec
M10
M12
M16
[kN]
21,9
31,9
60,0
[kN]
20,5
29,9
56,3
M10
M12
M16
M20 a)
91,4
11,9
16,7
35,7
45,2
11,9
16,7
35,7
M20
a)
b)
HDA-P(F), HDA-T(F)
HDA-PR, HDA-TR
c)
c)
[kN]
HDA-PR
for tfix
HDA-T, HDA-TF c)
82
M16
12,6
17,1
35,4
52,6
12,3
18,2
33,8
[mm]
[mm]
[kN]
10 15
<15 20
31 d) 31
10
<15
15
<20
38 d)
38
20
50
48
15 20 25 30 35 20 25 40 55
<20 <25 <30 <35 60 <25 <40 <55 100
67 d) 67 74 81 90 98 d) 98 112 119
[mm]
[mm]
10 15 10 15 20 30 20 25 30 35
<15 20 <15 <20 <30 50 <25 <30 <35 60
HDA-TR
[kN]
38 d) 38 47 d) 47 50 59 82 d)
82
85
91
HDA M20: only a galvanized 5m version is available
With overall partial safety factor for action F = 1,4. The partial safety factors for action depend on the type of
loading and shall be taken from national regulations. According ETAG 001, annex C, the partial safety factor is
G = 1,35 for permanent actions and Q = 1,5 for variable actions.
HDA-PF and HDA-TF anchors are not covered by ETA-99/0009
With use of centering washer (t = 5 mm) only
for tfix
c)
d)
M12
b)
HDA-P, HDA-PF
a)
b)
M20
a)
M10
6 / 2010
Materials
Mechanical properties of HDA
Anchor size
M10
HDA-P(F), HDA-T(F)
M12
M16
M20 a)
HDA-PR, HDA-TR
M10
M12
M16
Anchor bolt
Nominal tensile strength f uk [N/mm]
800
800
800
800
800
800
800
Yield strength fyk
[N/mm]
640
640
640
640
600
600
600
Stressed cross-section As [mm]
58,0
84,3
157
245
58,0
84,3
157
Moment of resistance W el [mm]
62,3
109,2
277,5
540,9
62,3
109,2
277,5
Characteristic bending
60
105
266
519
60
105
266
resistance without sleeve
[Nm]
M0Rk,s b)
Anchor sleeve
Nominal tensile strength f uk [N/mm]
850
850
700
550
850
850
700
Yield strength fyk
[N/mm]
600
600
600
450
600
600
600
a) HDA M20: only a galvanized 5m version is available
b) The recommended bending moment of the HDA anchor bolt may be calculated from Mrec = MRd,s / F =
.
.
.
.
MRk,s / (Ms F) = = (1,2 W el f uk) / (Ms F) , where the partial safety factor for bolts of grade 8.8 is MS = 1,25,
for A4-80 equal to 1,33 and the partial safety factor for action may be taken as F = 1,4. In case of HDA-T/TR/TF
the bending capacity of the sleeve is neglected, only the capacity of the bolt is taken into account.
Material quality
Part
Material
HDA-P / HDA-T (Carbon steel version)
Machined steel with brazed tungsten carbide tips, galvanised to min. 5 m
Sleeve:
Cold formed steel, grade 8.8, galvanised to min. 5 m
Bolt M10 - M16:
Cone machined, rod grade 8.8, galvanised to min. 5 m
Bolt M20:
HDA-PR / HDA-TR (Stainless steel version)
Machined stainless steel with brazed tungsten carbide tips
Sleeve:
Cone/rod: machined stainless steel
Bolt M10 - M16:
HDA-PF / HDA-TF (Sherardized version)
Machined steel with brazed tungsten carbide tips, shearadized
Sleeve:
Cold formed steel, grade 8.8, shearadized
Bolt M10 - M16:
Anchor dimensions
HDA-P / HDA-PR / HDA-PF
dS
dB
lS
SW
lB
HDA-T / HDA-TR / HDA-TF
dS
lS
lB
6 / 2010
dB
SW
83
Dimensions of HDA
Anchor size
lB
dB
[mm]
[mm]
ls
ls
[mm]
[mm]
100
120
dS
[mm]
19
21
29
35
dw
Sw
[mm]
[mm]
27,5
17
33,5
19
45,5
24
50
30
125
155
125
175
190
230
190
250
250
300
250
350
Setting
Drilling
The stop drill is required for drilling in order to achieve the correct hole depth.
Anchor
HDA-P/ PF/ PR M10x100/20
HDA-T/ TF/ TR M10x100/20
HDA-P/ PF/ PR M12*125/30
HDA-P/ PF/ PR M12*125/50
HDA-T/ TF/ TR M12*125/30
HDA-T/ TF/ TR M12*125/50
Setting
Drilling hammer
Setting tool
The setting system (tool and setting tool) is required for transferring the specific energy for the undercutting
process.
84
6 / 2010
HDA-P/T20-M10*100/20
HDA-P/T 22-M12*125/30
HDA-P/T 22-M12*125/50
TE 76 b)
TE 76-ATC b)
TE 70 b)
b)
TE 70-ATC
TE 75 b)
TE 50
TE 40
TE 40 AVR
TE 35
TE 24 a)
TE 25 a)
TE 56 b)
TE 56-ATC b)
HDA-P/T 30-M16*190/40
HDA-P/T 30-M16*190/60
HDA-P/T 37-M20*250/50
HDA-P/T 37-M20*250/100
a) 1st gear
b) max. impact energy
HDA-PR/TR 22-M12*125/30
HDA-PR/TR 22-M12*125/50
250 - 555
480 - 500
250 - 555
480 - 500
8,0 - 11,0
250 - 360
TE-Y-HDA-ST 37 M20
8,3 - 11,0
280 - 360
HDA-PR/TR 30-M16*190/40
HDA-PR/TR 30-M16*190/60
a) 1st gear
b) max. impact energy
6,5 - 7,5
480 - 500
250 - 360
Setting tool
TE 76 b)
TE 76-ATC b)
TE 70 b)
TE 70-ATC b)
TE 75 b)
TE 56 b)
TE 56-ATC b)
TE 50
TE 35
3,5 - 4,9
6,5 - 7,5
3,5 - 4,9
6,5 - 7,5
TE-Y-HDA-ST 30 M16
TE 24 a)
TE 25 a)
TE-C-HDA-ST 20 M10
TE-Y-HDA-ST 20 M10
TE-C-HDA-ST 22 M12
TE-Y-HDA-ST 22 M12
TE 76 b)
TE 76-ATC b)
TE 70 b)
TE 70-ATC b)
TE 75 b)
TE 40
TE 40 AVR
TE 56 b)
TE 56-ATC b)
TE 35
TE 50
TE 24 a)
TE 25 a)
Single
Speed
impact under load
energy [J]
[1/min]
Setting tool
HDA-PR/TR20-M10*100/20
Setting tool
HDA-PF/TF 20-M10*100/20
TE-C-HDA-ST 20 M10
3,5 4,0
610 - 630
HDA-PF/TF 22-M12*125/30
HDA-PF/TF 22-M12*125/50
TE-C-HDA-ST 22 M12
3,5 4,0
610 - 630
250 - 360
HDA-PF/TF 30-M16*190/40
HDA-PF/TF 30-M16*190/60
a) 1st gear
b) max. impact energy
6 / 2010
85
Setting instruction
HDA-P, HDA-PR, HDA-PF
86
6 / 2010
For detailed information on installation see instruction for use given with the package of the product.
Setting details
hS
HDA-P / HDA-PR / HDA-PF
df
tfix
hef
h1
hmin
hS
Marking
df
hef
tfix
h1
hmin
6 / 2010
87
Anchor size
Head marking
Nominal drill bit
diameter
Cutting diameter
of drill bit
Depth of drill hole
Anchorage depth
a)
Sleeve recess
Torque moment
For HDA-P/-PF/-PR
Clearance hole
Minimum base
material thickness
Fixture thickness
d0
[mm]
20
22
30
37
dcut,min
dcut,max
h1
hef
hs,min
hs,max
Tinst
[mm]
[mm]
[mm]
[mm]
[mm]
[mm]
[Nm]
20,10
20,55
107
100
2
6
50
22,10
22,55
133
125
2
7
80
30,10
30,55
203
190
2
8
120
37,15
37,70
266
250
2
8
300
df
[mm]
12
14
18
22
hmin
[mm]
180
200
270
350
tfix,min
tfix,max
[mm]
[mm]
0
20
0
30
0
50
40
0
60
50
100
For HDA-T/-TF/-TR
21
23
40
Clearance hole
df
[mm]
32
Minimum base
230-tfix
250-tfix
310-tfix
330-tfix
400-tfix
450-tfix
hmin
[mm] 200-tfix
material thickness
Min. fixture thickness
-Tension load only!
tfix,min [mm]
10
10
15
20
50
-Shear load - without
t
[mm]
15
15
20
25
50
use of centering washer fix,min
-Shear load - with
b)
t
[mm]
10
10
15
20
use of centering washer fix,min
Max. fixture thickness
tfix,max [mm]
20
30
50
40
60
50
100
a) use specified stop drill bit
b) with use of centering washer a reduction of tfix,min is possible for shear loading, details see ETA-99/0009
88
6 / 2010
Setting parameters
Anchor size
Minimum spacing
Minimum edge
distance
Critical spacing for
splitting failure
Critical edge distance
for splitting failure
Critical spacing for
concrete cone failure
Critical edge distance
for concrete cone
failure
smin
[mm]
cmin
[mm]
80
100
150
200
scr,sp
[mm]
300
375
570
750
ccr,sp
[mm]
150
190
285
375
scr,N
[mm]
300
375
570
750
ccr,N
[mm]
150
190
285
375
For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to be
reduced.
Critical spacing and critical edge distance for splitting failure apply only for non-cracked concrete. For cracked
concrete only the critical spacing and critical edge distance for concrete cone failure are decisive.
6 / 2010
89
Tension loading
The design tensile resistance is the lower value of
NRd,s
- Steel resistance:
NRd,c
= N0Rd,p fB
= N0Rd,c fB f1,N f2,N f3,N fre,N
HDA-P(F), HDA-T(F)
[kN]
M10
M12
M16
M20 a)
30,7
44,7
84,0
128,0
41,9
78,8
HDA-PR, HDA-TR
28,8
[kN]
HDA M20: only a galvanized 5m version is available
a)
Non-cracked concrete
Anchor size
M10
M12
M16
M20
b)
0
Rd,p
N
a)
b)
[kN]
Design pull-out resistance is not decisive in non-cracked concrete
HDA M20: only a galvanized 5m version is available
M10
M12
M16
16,7
23,3
50,0
M20
b)
63,3
Design concrete cone resistance NRd,c = N0Rd,c fB f1,N f2,N f3,N fre,N
Design splitting resistance a) NRd,sp = N0Rd,c fB f1,sp f2,sp f3,sp f h,sp fre,N
Cracked concrete
Non-cracked concrete
b)
M10
M12
M16
M20 b)
38,7
54,1
101,4
153,1
[kN]
Splitting resistance must only be considered for non-cracked concrete
HDA M20: only a galvanized 5m version is available
27,7
38,7
72,5
109,3
C 45/55
C 50/60
1,48
1,55
Anchor size
M10
M12
M16
M20
0
Rd,c
N
a)
b)
Influencing factors
Influence of concrete strength
Concrete strength designation
(ENV 206)
1/2 a)
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
fB =
(f ck,cube/25N/mm)
1
1,1
1,22
1,34
1,41
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
90
6 / 2010
0,7 + 0,3c/ccr,N 1
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,73
0,76
0,79
0,82
0,85
0,88
0,91
0,94
0,97
0,5(1 + c/ccr,N) 1
0,1
s/scr,sp
f 3,N =
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,5(1 + s/scr,N) 1
2/3
2,2
2,4
2,6
2,8
3,2
3,4
3,6
3,68
1,07
1,13
1,19
1,25
1,31
1,37
1,42
1,48
1,5
Influence of reinforcement
Anchor size
M8
a)
M10
a)
M12
M16
M20
M24
a)
0,8
0,85
0,9
1
1
1
f re,N = 0,5 + hef/200mm 1
a) This factor applies only for dense reinforcement. If in the area of anchorage there is reinforcement with a
spacing 150 mm (any diameter) or with a diameter 10 mm and a spacing 100 mm, then a factor f re,N = 1
may be applied.
Shear loading
The design shear resistance is the lower value of
- Steel resistance:
-
6 / 2010
VRd,s
VRd,cp = V0Rd,cp fB f1,N f2,N f3,N fre,N
0
Rd,c
VRd,c = V
fB f f h f4
91
HDA-PR
HDA-T, HDA-TF
b)
a)
M10
M12
M16
M20
[kN]
17,6
24,0
49,6
73,6
[kN]
17,3
25,6
47,4
[kN]
43,3
53,3
93,3
136,7
b)
HDA-TR
[kN]
53,4
65,4
114,3
a) HDA M20: only a galvanized 5m version is available
b) Values are valid for minimum thickness of the base plate tfix,min. For characteristic resistance to shear loads with
thicker base plates see ETA-99/0009 or use PROFIS software.
Design concrete pryout resistance VRd,cp = V0Rd,cp fB f1,N f2,N f3,N fre,N
Cracked concrete
Non-cracked concrete
Anchor size
M10
M16
M20
a)
M10
M12
M16
M20 a)
202,9
306,2
55,3
77,3
144,9
218,7
M12
0
77,5
108,3
V Rd,cp
[kN]
a) HDA M20: only a galvanized 5m version is available
Non-cracked concrete
Anchor size
M10
M12
M16
M20
b)
M10
M12
M16
M20
b)
cmin
[mm]
80
100
150
200
80
100
150
200
0
V Rd,c
[kN]
8,5
12,8
26,1
45,0
6,1
9,2
18,6
32,1
a) For anchor groups with more than two anchors only the anchors close to the edge must be considered.
b) HDA M20: only a galvanized 5m version is available
Influencing factors
Influence of concrete strength
Concrete strength designation
(ENV 206)
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
1/2 a)
fB =
(f ck,cube/25N/mm)
1
1,1
1,22
1,34
1,41
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
C 45/55
C 50/60
1,48
1,55
0,7 + 0,3c/ccr,N 1
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
0,73
0,76
0,79
0,82
0,85
0,88
0,91
0,94
0,97
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
0,9
92
6 / 2010
M8
0,8
M10
a)
0,85
M12
a)
0,9
M16
M20
M24
a)
This factor applies only for dense reinforcement. If in the area of anchorage there is reinforcement with a
spacing 150 mm (any diameter) or with a diameter 10 mm and a spacing 100 mm, then a factor f re,N = 1
may be applied.
Influence of angle between load applied and the direction perpendicular to the free edge
Angle
0 - 55
60
65
70
75
80
85
90 - 180
1,07
1,14
1,23
1,35
1,50
1,71
{h/(1,5 c)}
2/3
0,15
0,3
0,45
0,6
0,75
0,9
1,05
1,2
1,35
1,5
0,22
0,34
0,45
0,54
0,63
0,71
0,79
0,86
0,93
1,00
Influence of anchor spacing and edge distance a) for concrete edge resistance: f4
f4 = (c/hef)1,5 (1 + s / [3 c]) 0,5
Single
anchor 0,75 1,50 2,25
0,50
0,35
0,27 0,35 0,35
0,75
0,65
0,43 0,54 0,65
1,00
1,00
0,63 0,75 0,88
1,25
1,40
0,84 0,98 1,12
1,50
1,84
1,07 1,22 1,38
1,75
2,32
1,32 1,49 1,65
2,00
2,83
1,59 1,77 1,94
2,25
3,38
1,88 2,06 2,25
2,50
3,95
2,17 2,37 2,57
2,75
4,56
2,49 2,69 2,90
3,00
5,20
2,81 3,03 3,25
3,25
5,86
3,15 3,38 3,61
3,50
6,55
3,51 3,74 3,98
3,75
7,26
3,87 4,12 4,36
4,00
8,00
4,25 4,50 4,75
4,25
8,76
4,64 4,90 5,15
4,50
9,55
5,04 5,30 5,57
4,75
10,35 5,45 5,72 5,99
5,00
11,18 5,87 6,15 6,43
5,25
12,03 6,30 6,59 6,87
5,50
12,90 6,74 7,04 7,33
a) The anchor spacing and the edge
minimum edge distance cmin.
c/hef
93
Precalculated values
Design resistance calculated according ETAG 001, Annex C and data given in ETA-99/0009, issue 2008-03-25.
All data applies to concrete C 20/25 fck,cube =25 N/mm.
HDA-PF and HDA-TF anchors are not covered by the approval. For HDA-T and HDA-TR anchors the resistance to
shear loads is calculated for the minimum thickness of the base plate given in chapter setting details page 87.
Design resistance
Single anchor, no edge effects, shear without lever arm
Non-cracked concrete
Anchor size
Min. base material thickness hmin [mm]
HDA-T: Min. fixture thickness tfix [mm]
Tensile NRd
Cracked concrete
M10
180
15
M12
200
15
M16
270
20
M20
350
25
M10
180
15
M12
200
15
M16
270
20
M20
350
25
HDA-P(F), HDA-T(F)
[kN]
30,7
44,7
84,0
128,0
16,7
23,3
50,0
63,3
HDA-PR, HDA-TR
Shear VRd
HDA-P, HDA-PF
HDA-PR
HDA-T, HDA-TF
HDA-TR
[kN]
28,8
41,9
78,8
16,7
23,3
50,0
[kN]
[kN]
[kN]
[kN]
17,6
17,3
43,3
53,4
24,0
25,6
53,3
65,4
49,6
47,4
93,3
114,3
73,6
136,7
-
17,6
17,3
43,3
53,4
24,0
25,6
53,3
65,4
49,6
47,4
93,3
114,3
73,6
136,7
-
Single anchor, min. edge distance (c = cmin), shear without lever arm
Cracked concrete
Non-cracked concrete
Anchor size
Min. base material thickness hmin [mm]
HDA-T: Min. fixture thickness tfix [mm]
Min. edge distance cmin [mm]
Tensile NRd
HDA-P(F), HDA-T(F)
HDA-PR, HDA-TR
Shear VRd
HDA-P, HDA-PF
HDA-PR
HDA-T, HDA-TF
HDA-TR
M10
180
15
80
M12
200
15
100
M16
270
20
150
M20
350
25
200
M10
180
15
80
M12
200
15
100
M16
270
20
150
M20
350
25
200
[kN]
25,5
35,9
66,4
100,9
16,7
23,3
47,4
63,3
[kN]
8,5
12,8
26,1
45,0
6,1
9,2
18,6
32,1
Double anchor, no edge effects, min. spacing (s = smin), shear without lever arm
(load values are valid for one anchor)
Cracked concrete
Non-cracked concrete
Anchor size
Min. base material thickness hmin [mm]
HDA-T: Min. fixture thickness tfix [mm]
Min. spacing smin [mm]
Tensile NRd
HDA-P(F), HDA-T(F)
HDA-PR, HDA-TR
Shear VRd
HDA-P, HDA-PF
HDA-PR
HDA-T, HDA-TF
HDA-TR
94
M10
180
15
100
M12
200
15
125
M16
270
20
190
M20
350
25
250
M10
180
15
100
M12
200
15
125
M16
270
20
190
M20
350
25
250
[kN]
25,8
36,0
67,6
102,1
16,7
23,3
48,3
63,3
[kN]
[kN]
[kN]
[kN]
17,6
17,3
43,3
51,6
24,0
25,6
53,3
65,4
49,6
47,4
93,3
114,3
73,6
136,7
-
17,6
17,3
36,9
36,9
24,0
25,6
51,4
51,4
49,6
47,4
93,3
96,6
73,6
136,7
6 / 2010
Recommended loads
Single anchor, no edge effects, shear without lever arm
Non-cracked concrete
Anchor size
in. base material thickness hmin [mm]
HDA-T: Min. fixture thickness tfix [mm]
Tensile Nrec
Cracked concrete
M10
180
15
M12
200
15
M16
270
20
M20
350
25
M10
180
15
M12
200
15
M16
270
20
M20
350
25
HDA-P(F), HDA-T(F)
[kN]
21,9
31,9
60
91,4
11,9
16,6
35,7
45,2
HDA-PR, HDA-TR
Shear Vrec
HDA-P, HDA-PF
HDA-PR
HDA-T, HDA-TF
HDA-TR
[kN]
20,6
29,9
56,3
11,9
16,6
35,7
[kN]
[kN]
[kN]
[kN]
12,6
12,4
30,9
38,1
17,1
18,3
38,1
46,7
35,4
33,9
66,6
81,6
52,6
97,6
-
12,6
12,4
30,9
38,1
17,1
18,3
38,1
46,7
35,4
33,9
66,6
81,6
52,6
97,6
-
Single anchor, min. edge distance (c = cmin), shear without lever arm
Non-cracked concrete
Cracked concrete
Anchor size
Min. base material thickness hmin [mm]
HDA-T: Min. fixture thickness tfix [mm]
Min. edge distance cmin [mm]
Tensile Nrec
HDA-P(F), HDA-T(F)
HDA-PR, HDA-TR
Shear Vrec
HDA-P, HDA-PF
HDA-PR
HDA-T, HDA-TF
HDA-TR
M10
180
15
80
M12
200
15
100
M16
270
20
150
M20
350
25
200
M10
180
15
80
M12
200
15
100
M16
270
20
150
M20
350
25
200
[kN]
18,2
25,7
47,4
72,1
11,9
16,7
33,9
45,2
[kN]
6,1
9,2
18,6
32,1
4,4
6,5
13,3
22,9
Double anchor, no edge effects, min. spacing (s = smin), shear without lever arm
(load values are valid for one anchor)
Cracked concrete
Non-cracked concrete
Anchor size
Min. base material thickness hmin [mm]
HDA-T: Min. fixture thickness tfix [mm]
Min. spacing smin [mm]
Tensile Nrec
HDA-P(F), HDA-T(F)
HDA-PR, HDA-TR
Shear Vrec
HDA-P, HDA-PF
HDA-PR
HDA-T, HDA-TF
HDA-TR
M10
180
15
100
M12
200
15
125
M16
270
20
190
M20
350
25
250
M10
180
15
100
M12
200
15
125
M16
270
20
190
M20
350
25
250
[kN]
18,4
25,7
48,3
72,9
11,9
16,6
34,5
45,2
[kN]
[kN]
[kN]
[kN]
12,6
12,4
30,9
36,9
17,1
18,3
38,1
46,7
35,4
33,9
66,6
81,6
52,6
97,6
-
12,6
12,4
26,4
26,4
17,1
18,3
36,7
36,7
35,4
33,9
66,6
69,0
52,6
97,6
-
For the recommended loads an overall partial safety factor for action = 1,4 is considered. The partial safety
factors for action depend on the type of loading and shall be taken from national regulations. According ETAG 001,
annex C, the partial safety factor is G = 1,35 for permanent actions and Q = 1,5 for variable actions.
6 / 2010
95