Professional Documents
Culture Documents
Typical Applications
Base Stations Test Equipment Telecom & Wireless Infrastructure Digital Switching Military and Avionics
PXO
Features
9X14 J Leaded Surface Mount Package Reflow Process Compatible ACMOS, TTL and LVPECL Class B Screening optional Military Operating Temperature Range Optional
MC042, MC342, MC036 and MC037 1.0 to 800.0 MHz (ACMOS/TTL available up to 125 MHz. PECL and LVPECL frequencies above 220 MHz are achieved through use of PLL multiplier)
Overall tolerance (vs. initial accuracy, op. temp. range, vs load, vs supply, vs 1 year aging)
st
Max. +100 +50 +25 +15 +100 +50 +25 +50 +100 +100
Units ppm ppm ppm ppm ppm ppm ppm ppm ppm ppm
Operating temp range 0 +70C 0 +70C 0 +70C 0 +70C -40 +85C -40 +85C -40 +85C -55 +125C -55 +125C -0 +70C
Ordering Code C104 C505 C255 C155 F104 F505 F255 M505 M104 C104
Supply voltage change vs. load change vs aging /1 Year vs. aging / year (following Years)
-50 -25 -20 -100 -50 -25 -65 -100 Min -15 -25 -50 -100 -2 -1 -3 -1
Typ
+50 +25 +20 +100 +50 +25 +65 +100 Max. +15 +25 +50 +100 +2 +1 +3 +1
ppm ppm ppm ppm ppm ppm ppm ppm Units ppm ppm ppm ppm ppm ppm ppm ppm
0 +70C 0 +70C 0 70C -40 +85C -40 +85C -40 +85C -55 +125C -55 +125C Condition @ 25C @ 25C @ 25C @ 25C VS 5% Load 5%
C505 C255 C205 F104 F505 F255 M605 M104 Ordering Code T155 T255 T505 T104
5
www.vectron.com
C1300
PXO
RF output
Parameter Signal Load Signal Level (Vol) Signal Level (Voh) Rise and fall times for ACMOS (measured 10% to 90%) Duty cycle Signal Load Signal Level (Vol) Signal Level (Voh) Rise and fall times for TTL (measured 0.8V to 2.0V) Duty Cycle Signal Load Signal Level (Vol) Signal Level (Voh) Rise and fall times (measured @ 20% to 80%) Duty cycle LVPECL Jitter (rms) Period Jitter (pk-pk) 4.5 5 3 55 60 PECL/LVPECL 50 Vs -1.62 1000 600 55 10 0.5 40 45 40 TTL 10 0.5 VDC VDC ns ns % % Vs= 5.0V and 15pF load Vs= 5.0V and 15pF load 1.0 to 23.9 MHz 24 to 125 MHz @ 1.4V < 15 MHz @ 1.4V > 15 MHz RFP Into Vcc-2V or Thevenin Equivalent 4.5 3.0 10 6 3 55 60 Min Typ ACMOS 15 50 0.5 0.3 pF VDC VDC VDC VDC ns ns ns % % Vs= 5.0V and 15pF load Vs=3.3V and 15pF load Vs= 5.0V and 15pF load Vs=3.3V and 15pF load 1.0 to 23.9 MHz 24.0 to 79.9 MHz 80.0 to 125.0MHz @ 50% Vs< 15 MHz @ 50% Vs > 15 MHz RFT Max. Units Condition Ordering Code RFA
5
45 40
Vs- 1.025
45
VDC VDC ps ps % ps ps ps
<100 MHz > 100 MHz @ 50% Vdd BW = 10Hz to 20 MHz BW = 12 kHz to 20 MHz 10,000 Samples - Rising edge
www.vectron.com
C1300
PXO
Additional parameters
Screening Screening
6
B V
Output Enable
Logic "0" input = Outputs disabled (Tri-state) Logic "1" or floating input = Outputs enabled) Logic "0" or floating input = Outputs enabled Logic "1" input = Outputs disabled (Tri-state) 2 Handling & processing note g
-55 -62
Type B - LVPECL
Pin Length L N/A Code B1 E1=Enable/Disable pin 1 X = N/C pin 1 T= Tinned J leads X = No Tinning
8
Height H
Height H
Pin Length L
Pin Connections
1 2 3 Enable/Disable or N/C Ground (case) Output 4 Supply Voltage 1 2 3 Enable/Disable or N/C N/C Ground (Case)
Pin Connections
4 5 6 RF Output Complementary Output Supply Voltage
www.vectron.com
C1300
Type C - PECL
Code C1 E2 = Enable/Disable pin 2 X = N/C pin 2 T= Tinned J leads X = No Tinning
8
PXO
Height H 1.880.178
Pin Connections
1 2 3 N/C Enable/Disable or N/C Ground (Case) 4 5 6 RF Output Complemenatry Output Supply Voltage
Model C1300
Example : C1300
Package Code
A1
Enable/Disable
Tinning
T505
E1
Step 2
The factory representative will then respond with a Vectron Part Number in the following Configuration: Model C1300 Package Code [Customer Specified Package Code] Dash Dash Number [Factory Generated 4 digit number]
Notes: 1 Contact factory for improved stabilities or additional product options. Not all options and codes are available at all frequencies. 2 Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25C) 3 Phase noise degrades increasing output frequency. 4 Subject to technical modification. 5 Contact factory for availability. 6 Contact factory for other options. 7 Overall stabilities do not require an initial accuracy code. 8 Leads tinned IAW Vectron International standard procedure (GR-37409). 9 Vectron verification IAW Vectron International standard procedure (GR-37409).
www.vectron.com
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.