Professional Documents
Culture Documents
Contents
General information 1. Roof
1.1 Full rafter insulation, new build 1.2 On-roof insulation, new build/reconstruction 1.3 Common rafter insulation reconstruction, from inside 1.4 Common rafter insulation reconstruction, from outside 1.4.1 Common rafter insulation reconstruction, from outside/interior panelling PB 1.4.2 Common rafter insulation reconstruction, from outside/interior panelling HWL 1.4.3 Common rafter insulation reconstruction, from outside/interior panelling for profiled wood formwork 1.5 Flat roof P. 6 P. 7 P. 8 P. 9 P. 10 P. 12 P. 14 P. 16 P. 3
2. Wall
2.1 Brickwork reconstruction, from outside 2.2 Brickwork reconstruction, from inside 2.3 Stud wall reconstruction, from outside/inside 2.4 New build brickwork insulation, from outside 2.5 Timber frame construction 2.6 Prefabricated house reconstruction 2.7 Sold timber element P. 18 P. 21 P. 22 P. 24 P. 28 P. 30 P. 32
4. Concrete ceiling
4.1 Cement screed 4.2 Mastic asphalt 4.3 Sill plate/dry screed element 4.4 Solid wooden floor P. 38 P. 38 P. 39 S. 39
5. Beamed ceiling
Bare ceiling 5.1 Cement screed 5.2 Mastic asphalt 5.3 Sill plate/dry screed element 5.4 Solid wooden floor P. 40 P. 41 P. 42 P. 44 P. 45
General information
The brochure below entitled "Construction Recommendations" provides a summary of the design examples for roof, wall, floor and ceiling, with the relevant structural values for the protection against cold winter temperatures, hot summer temperatures, noise and fire.All constructions are calculated in accordance with DIN 4108 and hence tested for diffusion, moisture and condensate. Pages 48 and onwards also contain roof and wall constructions, for which fire and noise protection classifications are described. These are referred to as general building inspection certificates (AbPs). For example, exterior wall constructions classified to F90-B along with their noise protection values are stated. The result is a comprehensive work of reference, which considerably simplifies component planning. To create a failure-free construction, the manufacturer's data and/or the installation instructions for all materials used must be observed.
Phase shift and amplitude damping with 180 mm GUTEX Thermosafe-homogen insulation Time lag (10 hours)
Recommendations for new build For new build, the entire building envelope and the building technology is considered from an energy perspective as an integrated unit.
Component Exterior wall Steep roof/top floor ceiling Flat roof 0.16 0.16 0.14 U-factor (W/m2K) Recommendation Visionary 0.12 0.12 0.12
Time Decrement
General information
Acoustic insulation
The requirements and recommendations are defined in DIN 4109. Components are supposed to dampen and/ or minimise the noise outside and inside the building. For noise protection, a distinction is drawn between airborne noise and impact noise. Airborne noise protection is relevant for wall and roof components, impact noise protection for floor and ceiling constructions. Floor:
Recommendations for the noise protection of ceilings within the dwelling for standard noise protection for improved noise protection Airborne noise RW 50 dB RW 55 dB Impact noise Ln,w 57 dB Ln,w 46 dB
Requirements and recommendations for the noise protection partition ceilings in apartment buildings Airborne noise Impact noise Ln,w 53 dB from DIN 4109 RW 54 dB for improved noise protection from supplement 2 DIN 4109 RW 55 dB Ln,w 46 dB
Interior walls: Requisite airborne noise insulation for protection against noise transmission from an external living and working area
Components Multi-story buildings with apartments and offices Partition walls and walls between external work areas Staircase walls and walls next to the building corridors Walls next to thoroughfares In hospitals: - Walls between patients' rooms - Corridors and patients' rooms - Examination rooms - Consultation rooms Schools: walls between classrooms Walls between classrooms and staircases emp. Rw in dB 53 52 55
47
47 52
1) No requirements are placed on exterior components of exterior rooms, where the penetrating outside noise, due to the activities being carried out inside the rooms, make only a secondary contribution to the inside noise level. 2) The requirements must be set out here on account of the local conditions.
Correction values for the requisite noise insulation factor Rw,res of the exterior component depending on the condition of the component surface S (W+F) for the ground area of the room S(G) S (W+F) / S(G) Correction value 2.5 +5 dB 2.0 +4 dB 1.6 +3 db 1.3 +2 dB 1.0 +1 dB 0.8 0 dB 0.6 -1 dB 0.5 -2 dB 0.4 -3 dB
Semi-detached houses and terraced houses Recommendations for improved noise protection Partition walls
emp. RW (dB) 57
Fire protection
GUTEX understands fire safety as protection for people and animals against fire. Fire safety, however, also means minimising the resultant damage. The requirements for building fire safety are regulated by the countries concerned. There are two distinctly different requirements. One is the building material class or its fire behaviour and the other is the fire resistance class of a component. Building material classes or fire behaviour fall into classes A = "nonflammable" to F = "highly-flammable". For the construction industry, however, the minimum requirement is Class B2 = "normally flammable" (Germany) or Class E = "normally flammable" (Europe). Testing institutes conduct flammability tests on building productions and classify them accordingly. Fire resistance falls into classes F 30 F180.The classification is in turn carried out by testing institutes and the product is certified accordingly. In this case, it is not the product that is classified but an entire component. F 30 means, for example, that a component will withstand fire for 30 minutes without structural failure or burn through. This guarantees that a construction in this category offers, in case of fire, 30 minutes to move people and animals out of the hazard zones.
Environmental compatibility
In the case of an ecological insulating material, the principle of sustainability over the entire life cycle, from production to processing and use, through to disposal should be the top priority. All trees bind, during their lifetime, the same amount of CO2, which they emit into the environment when they rot or are burned. Because GUTEX soft board is made from woodchip that occurs as a byproduct in the saw mill, it contains CO2, which is not emitted into the atmosphere as a greenhouse gas. GUTEX obtains the woodchip from the saw mills surrounding its Waldshut-Tiengen site in the south of the Black Forest. Other plus factors in the eco-balance are wood from sustainable forests and short supplier transport routes . Unless contaminated by foreign material, GUTEX softboard can be recycled at the end of its utilisation pathway . GUTEX products carry the quality mark "natureplus". The tough criteria that have to be met for the "natureplus" to be awarded are reviewed annually by the umbrella association of environmental organisations, institutes, construction biologists, companies and associations. The basic criteria for the award are high technical product quality completely harmless to health environmentally compatible production sustainability of the raw materials used
User friendly
Gutex insulating board exhibits extremely narrow dimensional tolerances and is produced to tough quality standards. This, coupled with detailed instructions makes for simple processing.
Made in Germany
For almost 80 years now, "GUTEX Holzfaserplattenwerk", a family-owned enterprise based in the Black Forest has been producing wood fibreboard insulation products at its Waldshut-Tiengen plant in the south of the area. All GUTEX insulating board carries the CE and marks is produced to the specified standard. The composite thermal insulation system from GUTEX is also approved by the building authorities.
Recyclability
GUTEX wood fibreboard is recyclable and can, unless contaminated by wood preservatives, be returned for reuse.
1. Roof
1.1.1 Structure:
- Tile battens - Counter battens - GUTEX Multiplex-top - GUTEX Thermofibre/GUTEX Thermoflex between the rafters - Vapour barrier/air seal - Battens - Facing GUTEX Thermofibre/ Thermoflex (mm) 180 22 200 220 240 180 28 200 220 240 180 35 200 220 240 Noise insulation value RW, R (dB) 2) 48
1.1.2 Structure:
- Tile battens - Counter battens - GUTEX Ultratherm - GUTEX Thermofibre/GUTEX Thermoflex between the rafters - Vapour barrier/air seal - Battens - Facing GUTEX Thermofibre/ Thermoflex (mm) 180 200 220 240 60 180 200 220 240 180 200 220 240 180 200 220 240 120 180 200 220 240 180 200 220 240 180 200 220 240 Noise insulation value RW, R (dB) 2) 46
U-factor (W/m2K)1) 0.22 0.20 0.18 0.17 0.21 0.19 0.18 0.17 0.20 0.19 0.17 0.16
Phase shift (h) 9.5 10.2 11.0 11.7 10.0 10.7 11.4 12.1 10.5 11.2 11.9 12.7
U-factor (W/m2K)1) 0.19 0.17 0.16 0.15 0.18 0.17 0.16 0.15 0.16 0.15 0.14 0.14 0.15 0.14 0.13 0.13 0.14 0.13 0.13 0.12 0.13 0.13 0.12 0.11 0.12 0.12 0.11 0.11
Phase shift (h) 11.6 12.3 13.1 13.8 12.4 13.1 13.8 14.6 13.9 14.6 15.3 16.1 15.3 16.0 16.8 17.5 16.7 17.4 18.1 18.9 18.1 18.8 19.5 20.2 19.4 20.2 20.9 21.6
50 47 48 49 47 48 100 80
47
48
49
50
140
50
160
50
1) Calculation with 10 % wood content 2) The noise levels refer to a construction with GUTEX Thermoflex, a roof covering with concrete roofing tiles and double-threaded bolt fastening
1.2.1 Structure:
- Tile battens - Counter battens - GUTEX Multiplex-top/GUTEX Ultratherm - GUTEX Thermosafe-homogen - Vapour barrier/air seal - Exposed formwork 24 mm - Exposed rafters
1.2.2 Structure:
- Tile battens - Counter battens - GUTEX Multiplex-top/GUTEX Ultratherm - GUTEX Thermofibre between double I-joists - Vapour barrier/air seal - Exposed formwork 24 mm - Exposed rafters
Thickness (mm)
GUTEX Thermosafe- U-factor1) homogen (W/m2K) (mm) 140 160 180 200 220 240 140 160 180 200 220 240 200 220 240 200 220 240 200 220 240 200 220 240 200 220 200 0.22 0.20 0.18 0.16 0.15 0.14 0.22 0.19 0.18 0.16 0.15 0.14 0.16 0.14 0.13 0.15 0.14 0.13 0.14 0.13 0.12 0.14 0.13 0.12 0.13 0.12 0.12
Phase shift (h) 11.7 12.9 14.0 15.2 16.4 17.5 12.0 13.2 14.3 15.5 16.6 17.8 15.9 17.1 18.2 16.4 17.6 18.7 17.5 18.6 19.8 18.2 19.4 20.5 19.7 20.8 21.1
Thickness (mm)
U-factor 1) (W/m2K) 0.17 0.15 0.14 0.16 0.15 0.14 0.15 0.14 0.13 0.15 0.14 0.13 0.14 0.13 0.12 0.13 0.12 0.11
Phase shift (h) 10.8 11.4 12.0 11.3 11.9 12.6 12.5 13.1 13.7 13.3 13.9 14.5 14.8 15.4 16.0 16.2 16.8 17.5
28 GUTEX Multiplex-top 35
18
GUTEX Multiplextop
22
28
60 GUTEX Ultratherm 80
35
50 GUTEX Ultratherm
100
220 240
60 80 100
1) Calculation with 10 % wood content 2) The noise levels refer to a construction with GUTEX Thermoflex, a roof covering with concrete roofing tiles and double-threaded bolt fastening
Roof
1. Roof
1. Roof
U-factor (W/m2K) 1) 0.23 0.21 0.22 0.20 0.19 0.17 0.22 0.20 0.18 0.17 0.16 0.20 0.18 0.17 0.16 0.15 0.18 0.16 0.15 0.14 0.14 0.16 0.15 0.14 0.13 0.13
Phase shift (h) 9.8 10.5 10.2 10.9 11.6 12.3 10.7 11.4 12.1 12.8 13.5 11.9 12.6 13.3 14.0 14.8 13.2 13.9 14.6 15.3 16.0 14.5 15.2 15.9 16.6 17.3
U-factor 1) (W/m2K) 0.23 0.21 0.19 0.17 0.16 0.22 0.20 0.19 0.17 0.16 0.15 0.22 0.20 0.18 0.17 0.16 0.15 0.14 0.19 0.18 0.17 0.15 0.14 0.14 0.13
Phase shift (h) 12.5 13.2 13.9 14.6 15.3 13.2 13.8 14.4 15.1 15.8 16.6 13.7 14.3 15.0 15.6 16.3 17.0 17.7 14.9 15.5 16.1 16.8 17.5 18.2 18.9
40
60
49 80
100 120 140 160 180 200 80 100 120 100 140 160 180 200
46
1) Calculation with 10 % wood content 2) Values as per "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value, incl. allowance
Ampack, membrane Ampatop Protecta und Ampatop Protecta plus Isocell, membranes OMEGA MONO 200 and OMEGA LIGHT CaPlast, membranes CaTop M 170 and CaTop M 120 Frch, membrane Saniflex 002 Saint Gobain, membranes NOVIPro UDB 310/-SK and NOVIPro UDB 210/-SK BWK, membranes Difflex Thermo ND; REWASI TOP 130 and REWASI TOP 150 Raab Karcher, membrane NOVIPro Alujet, membranes JKE Basic and JKE Professional
40
The insulation thickness ratios described in the relevant tables must be respected.
60
When using air-tight interior panelling, the air-tight membrane is not required.
80
47
100
120
1) Calculation with 10 % wood content 2) Values as per "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value, incl. allowance
Roof
1. Roof
1. Roof
GUTEX GUTEX Noise insulation Thermofibre/ U-factor Ultratherm Phase shift (h) value 2 1) Thermoflex (W/m K) (mm) RW, R (dB) 2) (mm) 140 0.22 10.2 160 0.20 10.9 50 47 180 0.19 11.6 200 0.17 12.3 120 0.23 10.3 140 0.21 11.0 60 160 0.19 11.7 47 180 0.18 12.4 200 0.17 13.1 120 0.21 11.8 140 0.19 12.5 80 160 0.18 13.2 47 180 0.16 13.9 200 0.15 14.6 120 0.19 13.2 140 0.18 13.9 100 160 0.16 14.6 48 180 0.15 15.3 200 0.14 16.0 120 0.17 14.6 140 0.16 15.3 120 160 0.15 16.0 49 180 0.14 16.7 200 0.13 17.4 120 0.16 15.9 140 0.15 16.6 140 160 0.14 17.4 49 180 0.13 18.1 200 0.13 18.8 120 0.15 17.3 140 0.14 18.0 160 160 0.13 18.7 50 180 0.12 19.4 200 0.12 20.2
Mineral wool 035 (mm) 120 120 140 160 120 140 160 180 120 140 160 180 200 120 140 160 180 200 120 140 160 180 200 120 140 160 180 200
U-factor (W/m2K) 1) 0.24 0.22 0.20 0.19 0.20 0.18 0.17 0.16 0.18 0.17 0.16 0.15 0.14 0.17 0.16 0.15 0.14 0.13 0.16 0.15 0.14 0.13 0.12 0.15 0.14 0.13 0.12 0.11
Phase shift (h) 8.1 8.9 9.2 9.6 10.4 10.8 11.2 11.5 11.9 12.3 12.6 13.0 13.3 13.3 13.6 14.0 14.4 14.7 14.6 15.0 15.4 15.7 16.1 16.0 16.4 16.7 17.1 17.4
80
47
100
48
120
49
140
49
160
50
*Note: With this construction, the sd-value for the air-tight membrane must not exceed 0.03m.
1) Calculation with 10 % wood content 2) Values as per "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value, incl. allowance 3) When using GUTEX Thermofibre, air-tight interior panelling must be produced
Roof
1. Roof
1. Roof
50
47
50
47
60
47
60
47
80
47
80
47
100
48
100
48
120
49
120
49
140
49
140
49
160
50
160
50
1) Calculation with 10 % wood content 2) Values in accordance with "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value incl. allowance 3) When using GUTEX Thermofibre, air-tight interior panelling must be produced
1) Calculation with 10 % wood content 2) Values as per "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value, incl. allowance
Roof
1. Roof
1. Roof
GUTEX GUTEX Thermofibre/ Ultratherm Thermoflex (mm) (mm) 140 160 50 180 200 120 140 60 160 180 200 120 140 80 160 180 200 120 140 100 160 180 200 120 140 120 160 180 200 120 140 140 160 180 200 120 140 160 160 180 200
U-factor (W/m2K)1) 0.22 0.20 0.19 0.17 0.23 0.21 0.19 0.18 0.16 0.21 0.19 0.18 0.16 0.15 0.19 0.17 0.16 0.15 0.14 0.17 0.16 0.15 0.14 0.13 0.16 0.15 0.14 0.13 0.12 0.15 0.14 0.13 0.12 0.12
Phase shift (h) 10.7 11.4 12.2 12.9 10.8 11.5 12.2 12.9 13.7 12.3 13.0 13.7 14.4 15.2 13.7 14.4 15.1 15.9 16.6 15.1 15.8 16.5 17.2 18.0 16.5 17.2 17.9 18.6 19.3 17.9 18.6 19.3 20.0 20.7
< 47
< 47
< 48
< 49
< 49
< 50
GUTEX Mineral wool Ultratherm 035 (mm) (mm) 120 140 160 50 180 200 120 140 160 60 180 200 120 140 80 160 180 200 120 140 100 160 180 200 120 140 120 160 180 200 120 140 140 160 180 200 120 140 160 160 180 200
U-factor (W/m2K)1) 0.23 0.21 0.19 0.18 0.16 0.22 0.20 0.18 0.17 0.16 0.20 0.18 0.17 0.16 0.15 0.18 0.17 0.16 0.14 0.14 0.17 0.15 0.14 0.14 0.13 0.15 0.14 0.13 0.13 0.12 0.14 0.13 0.13 0.12 0.11
Phase shift (h) 8.6 8.9 9.2 9.6 9.9 9.4 9.8 10.1 10.4 10.7 11.0 11.3 11.7 12.0 12.3 12.4 12.8 13.1 13.4 13.8 13.8 14.2 14.5 14.8 15.1 15.2 15.5 15.9 16.2 16.5 16.6 16.9 17.2 17.6 17.9
< 47
< 47
< 47
< 48
< 49
< 49
< 49
1) Calculation with 10 % wood content 2) Values in accordance with "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value incl. allowance 3) When using GUTEX Thermofibre, air-tight interior panelling must be produced
GUTEX Ultratherm (mm) 50 0.25 9.0 0.22 9.7 0.20 10.4 0.19 11.1 0.17 11.8 0.22 9.2 0.20 9.9 0.19 10.7 0.17 11.4 0.21 9.5 0.19 10.2 0.17 10.9 60 0.23 9.8 0.21 10.4 0.19 11.2 0.18 11.9 0.17 12.6 0.21 10.0 0.20 10.7 0.18 11.5 0.17 12.2 0.20 10.3 0.18 11.0 0.17 11.7 80 0.21 11.3 0.19 12.0 0.18 12.7 0.16 13.4 0.15 14.1 0.19 11.6 0.18 12.3 0.17 13.0 0.15 13.7 0.18 11.8 0.17 12.5 0.15 13.2
0.28 7.9 0.25 8.5 0.22 9.2 0.20 9.9 0.19 10.7 0.25 8.1 0.22 8.8 0.20 9.5 0.19 10.3 0.22 8.4 0.20 9.1 0.19 9.8
Roof
1. Roof
1. Flat roof
Roof
1. Flat roof
2. Exterior wall
Phase shift (h) 12.5 13.3 14.3 15.4 16.7 17.9 19.2
GUTEX Thermosafehomogen (mm) 100 120 140 160 180 200 220 240 240 240
U-factor (W/m2K) 0.27 0.23 0.21 0.19 0.17 0.15 0.14 0.13 0.12 0.12
Phase shift (h) 16.1 17.3 18.4 19.6 20.7 21.9 23.1 24.2 25.5 26.8
1) Assumed
2. Exterior wall
GUTEX Thermofibre/ Thermoflex (mm) 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180
U-factor (W/m2K)2) 0.24 0.22 0.20 0.21 0.20 0.18 0.19 0.18 0.17 0.18 0.16 0.15 0.16 0.15 0.14 0.15 0.14 0.13 0.14 0.13 0.12 0.13 0.12 0.12
Phase shift (h) 15.2 15.9 16.6 16.5 17.2 17.9 17.9 18.6 19.3 19.3 20.0 20.7 20.6 21.3 22.0 21.8 22.5 23.3 23.1 23.8 24.5 24.4 25.1 25.8
40
60
80
100
120
140
160
1) Assumed
Wall
2. Exterior wall
Phase shift (h) 20.1 21.2 22.4 23.8 24.9 26.1 27.5
U-factor (W/m2K)2) 0.22 0.20 0.18 0.20 0.18 0.17 0.17 0.16 0.15 0.16 0.15 0.14 0.15 0.14 0.13
Phase shift (h) 16.8 17.5 18.2 18.4 19.1 19.8 19.7 20.4 21.1 21.1 21.8 22.5 22.4 23.1 23.8
40
80 100
60
80
100
120
160 180
2. Exterior wall
Phase shift (h) 12.7 14.2 15.5 16.7 17.9 19.2 20.5
1) Assumed
Wall
2. Exterior wall
GUTEX Thermosafehomogen (mm) 100 120 140 160 180 200 220 240 240 240
U-factor (W/m2K) 0.27 0.24 0.21 0.19 0.17 0.16 0.14 0.13 0.13 0.12
Phase shift (h) 12.5 13.6 14.8 16.0 17.1 18.3 19.4 20.6 21.8 23.1
1) Assumed
2. Exterior wall
Phase shift (h) 9.3 10.8 12.1 13.3 14.6 15.8 17.1
1) Assumed
Wall
2. Exterior wall
1) Assumed 2) Assumed
2. Exterior wall
GUTEX GUTEX Multitherm Thermosafe-homogen (mm) (mm) 100 120 140 160 180 200 220 240 240 240 20 20 20 20 20 20 20 20 40 60
U-factor (W/m2K) 0.13 0.13 0.12 0.11 0.10 0.10 0.09 0.09 0.09 0.08
Phase shift (h) 30.5 31.7 32.8 34 35.2 36.3 37.5 38.6 39.9 41.2
GUTEX Thermofibre/ Thermoflex (mm) 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180 140 160 180
U-factor (W/m2K)2) 0.13 0.12 0.11 0.12 0.11 0.11 0.11 0.11 0.10 0.11 0.10 0.10 0.10 0.10 0.09 0.10 0.09 0.09 0.09 0.09 0.08 0.09 0.08 0.08
Phase shift (h) 29.8 30.5 31.2 31.0 31.8 32.5 32.5 33.2 33.9 33.8 34.5 35.3 35.1 35.9 36.6 36.4 37.1 37.8 37.7 38.4 39.1 38.9 39.6 40.4
40
60
80
100
120
140
160
Wall
2. Exterior wall
1) Assumed 2) Assumed
2. Exterior wall
GUTEX GUTEX Thermofibre/ U-factor Thermowall/-gf GUTEX (W/m2K) 1) (mm) Thermoflex (mm) 140 40 160 180 140 60 160 180 140 80 160 180 140 100 160 180 140 120 160 180 120 140 140 160 120 160 140 160 0.12 0.11 0.11 0.11 0.11 0.10 0.11 0.10 0.10 0.10 0.10 0.09 0.10 0.10 0.09 0.10 0.09 0.09 0.09 0.09 0.08
Phase shift (h) 31.4 32.1 32.8 33.0 33.7 34.4 34.3 35.0 35.7 35.7 36.4 37.1 37.0 37.7 38.4 37.7 38.4 39.1 39.0 39.7 40.4
80
120 140
Wall
2. Exterior wall
20
40
60
80
100
120
140
160
GUTEX Thermofibre/ U-factor1) Thermoflex (W/m2K) (mm) 160 0.23 180 0.21 200 0.19 220 0.18 240 0.17 160 0.21 180 0.19 200 0.17 220 0.16 240 0.15 160 0.18 180 0.17 200 0.16 220 0.15 240 0.14 160 0.17 180 0.16 200 0.15 220 0.14 240 0.13 160 0.15 180 0.14 200 0.14 220 0.13 240 0.12 160 0.14 180 0.13 200 0.13 220 0.12 240 0.11 160 0.13 180 0.13 200 0.12 220 0.11 240 0.11 160 0.12 180 0.12 200 0.11 220 0.11 240 0.10
Phase shift (h) 9.5 10.2 11.0 11.7 12.4 10.8 11.5 12.3 13.0 13.7 12.2 12.9 13.7 14.4 15.1 13.6 14.3 15.0 15.8 16.5 14.9 15.6 16.3 17.1 17.8 16.2 16.9 17.6 18.3 19.1 17.4 18.2 18.9 19.6 20.3 18.7 19.4 20.1 20.9 21.6
20
40
60
80 > 45 100
120
140
160
GUTEX Thermofibre/ Thermoflex (mm) 160 180 200 220 240 160 180 200 220 240 160 180 200 220 240 160 180 200 220 240 160 180 200 220 240 160 180 200 220 240 160 180 200 220 240 160 180 200 220 240
U-factor1) (W/m2K) 0.18 0.16 0.15 0.14 0.14 0.16 0.15 0.14 0.13 0.13 0.15 0.14 0.13 0.12 0.12 0.14 0.13 0.12 0.12 0.11 0.13 0.12 0.12 0.11 0.11 0.12 0.11 0.11 0.10 0.10 0.11 0.11 0.10 0.10 0.09 0.11 0.10 0.10 0.09 0.09
Phase shift (h) 13.0 13.7 14.4 15.2 15.9 14.3 15.0 15.8 16.5 17.2 15.7 16.4 17.2 17.9 18.6 17.1 17.8 18.5 19.3 20.0 18.4 19.1 19.8 20.6 21.3 19.7 20.4 21.1 21.8 22.6 20.9 21.7 22.4 23.1 23.8 22.2 22.9 23.6 24.4 25.1
> 45
1) Calculation with 10 % wood content 2) Values in accordance with "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value incl. allowance
2. Exterior wall
GUTEX Thick- Thermofibre/ Uness factor1) Thermoflex (mm) (W/m2K) (mm) 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 0.23 0.21 0.19 0.18 0.16 0.15 0.21 0.19 0.18 0.16 0,15 0.14 0.18 0.17 0.16 0.15 0.14 0.13 0.17 0.15 0.14 0.14 0.13 0.12 0.15 0.14 0.13 0.13 0.12 0.11 0.14 0.13 0.13 0.12 0.11 0.11 0.13 0.12 0.12 0.11 0.11 0.10
Phase shift (h) 10.4 11.1 11.8 12.6 13.3 14.0 12.0 12.7 13.4 14.2 14.9 15.6 13.3 14.0 14.7 15.5 16.2 16.9 14.7 15.4 16.1 16.9 17.6 18.3 16.1 16.8 17.5 18.2 18.8 19.7 17.4 18.1 18.8 19.5 20.3 21.0 18.8 19.5 20.2 20.9 21.6 22.3
GUTEX Thick- Thermofibre/ U-factor1) ness Thermoflex (W/m2K) (mm) (mm) 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 140 160 180 200 220 240 0.18 0.16 0.15 0.14 0.13 0.13 0.16 0.15 0.14 0.13 0.13 0.12 0.15 0.14 0.13 0.12 0.12 0.11 0.14 0.13 0.12 0.12 0.11 0.10 0.13 0.12 0.11 0.11 0.10 0.10 0.12 0.11 0.11 0.10 0.10 0.09 0.11 0.11 0.10 0.10 0.09 0.09
40 GUTEX Thermowall-gf 60
40 GUTEX Thermowall-gf 60
40
80
80
100
100
GUTEX Thermowall
120
44
GUTEX Thermowall
120
140
140
160
160
Noise Phase insulation value shift RW . R (h) (dB) 2) 13.9 14.6 15.3 16.0 16.8 17.5 42 15.5 16.2 16.9 17.7 18.4 19.1 16.8 17.5 18.2 19.0 19.7 20.4 18.2 18.9 19.6 20.3 21.1 21.8 19.6 20.3 21.0 47 21.7 22.4 23.1 20.9 21.6 22.3 23.0 23.8 24.5 22.2 23.0 23.7 24.4 25.1 25.8
1) Calculation with 10 % wood content 2) Executed in accordance with inspection certificate P-SAC-02/III-321
2. Exterior wall
GUTEX Thermofibre/ GUTEX Thermoflex Thermowall/-gf between timber (mm) uprights (mm) 40 60 80 140 100 120 140 160 40 60 80 160 100 120 140 160
U-factor (W/mK) 1) 0.23 0.21 0.18 0.16 0.15 0.14 0.13 0.21 0.19 0.17 0.15 0.14 0.13 0.12
U-factor (W/mK) 1) 0.22 0.20 0.18 0.17 0.15 0.14 0.13 0.20 0.18 0.17 0.15 0.14 0.13 0.12
10.6 12.2 13.6 14.9 16.3 17.6 19.0 11.3 13.0 14.3 15.6 17.0 18.3 19.7 160 140
10.3 11.7 13.1 14.4 15.7 17.0 18.2 11.0 12.5 13.8 15.1 16.4 17.7 18.9
2. Exterior wall
U-factor (W/mK) 1) 0.22 0.20 0.18 0.17 0.15 0.14 0.13 0.20 0.18 0.17 0.15 0.14 0.13 0.12
10.3 11.7 13.1 14.4 15.7 17.0 18.2 11.0 12.5 13.8 15.1 16.4 17.7 18.9
140
160
Wall
2. Exterior wall
2.7 Solid wood element
U-factor Phase shift (h) Noise insulation (W/mK) value RW . R(dB) 1) 0.21 0.19 0.17 0.16 18.5 19.8 21.0 22.3 < 50
GUTEX Thermosafehomogen (mm) 100 120 140 160 180 200 220 240
U-factor (W/mK) 0.24 0.21 0.19 0.17 0.16 0.14 0.13 0.13
Phase shift (h) Noise insulation value RW . R(dB) 1) 15.0 16.2 17.3 18.5 19.7 20.8 22.0 23.1 < 45
1) Values in accordance with "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value incl. allowance
2. Exterior wall
2.7 Solid wood element
GUTEX Thermosafe-homogen (mm) 100 120 140 160 180 200 220 240
U-factor Phase shift (h) (W/mK) 0.18 0.17 0.15 0.14 0.13 0.12 0.11 0.11 19.1 20.2 21.4 22.6 23.7 24.9 26.0 27.2
GUTEX Thermofibre/Thermoflex (mm) 200 220 240 300 360 400 200 220 240 300 360 400 200 220 240 300 360 400
U-factor (W/mK) 1) 0.16 0.15 0.15 0.13 0.11 0.11 0.15 0.14 0.14 0.12 0.11 0.10 0.14 0.13 0.13 0.11 0.10 0.10
Phase shift (h) 16.3 17.1 17.8 20.0 22.2 23.6 17.6 18.4 19.1 21.3 23.5 24.9 19.0 19.8 20.5 22.7 24.9 26.3
20 < 47
40
60
1) Calculation with 10 % wood content 2) Values in accordance with "Informationsdienst Holz", series 3, part 3, sequence 4, RW , R = calculated value incl. allowance
Wall
2. Exterior wall
2.7 Solid wood element
GUTEX Thermowall U-factor (W/mK) (mm) 100 120 140 160 0.21 0.19 0.17 0.16
38
40
2. Exterior wall
2.7 Solid wood element
U-factor (W/mK)1) 0.13 0.12 0.12 0.10 0.09 0.09 0.12 0.11 0.11 0.10 0.09 0.09 0.11 0.11 0.10 0.09 0.08 0.08
Phase shift (h) 22.0 22.7 23.5 25.7 27.8 29.3 23.6 24.3 25.1 27.2 29.4 30.9 24.9 25.6 26.4 28.5 30.7 32.2
1) Calculation with 10 % wood content 2) Execution in accordance with inspection certificate P-SAC-02/III-321
Wall
Panelling (mm) OSB board 15 OSB board 15 Plasterboard 12.5 Plasterboard 12.5 Fibre reinforced plasterboard 12.5 Fibre reinforced plasterboard 12.5
Panelling (mm) Plasterboard 9.5 Plasterboard 12.5 Plasterboard 12.5 Fibre reinforced plasterboard 10 Fibre reinforced plasterboard 12.5 Fibre reinforced plasterboard 12.5
60 140
60 140
0.59 0.29
50 50
Deep timGUTEX Noise insulaU-factor 1) ber uprights Thermosafe tion value (W/m2K) (mm) (mm) RW (dB) 60 40 0.66 47
can be up to 3 dB worse when using GUTEX Thermoflex 1) Calculation with 10 % wood content 2) There are still no noise values for constructions using GUTEX Thermofibre
Plasterboard 12.5 Plasterboard 9.5 Plasterboard 9.5 OSB board 15 OSB board 15 Plasterboard 9.5 Fibre reinforced plasterboard 10 OSB board 15 OSB board 15 Fibre reinforced plasterboard 10 Fibre reinforced plasterboard 10 Fibre reinforced plasterboard 12.5 Fibre reinforced plasterboard 12.5 Fibre reinforced plasterboard 10
60
40
0.61
47
140
120
0.29
51
60
60
0.58
52
140
140
0.29
52
Panelling (mm) Plasterboard 9.5 Plasterboard 12.5 Plasterboard 12.5 Plasterboard 9.5 Fibre reinforced plasterboard 10 Fibre reinforced plasterboard 12.5 Fibre reinforced plasterboard 12.5 Fibre reinforced plasterboard 10
U-factor (W/m2K)
125
100
0.79
54
50
40
1.17
55
125
100
0.84
62
4. Concrete ceiling
New build and reconstruction
Insulating layer (mm) 40 60 80 100 120 140 21/20 31/30 2x21/20 2x31/30 21/20 + 31/30
GUTEX Thermosafe-wd
GUTEX Thermofloor
Installation height (mm) 90 110 130 150 170 190 70 80 90 110 100
Standard U-factor impact (W/m2K) noise level Lnw (dB) 0.68 0.51 0.40 0.33 0.28 0.25 1.05 55 0.83 54 0.68 55 0.51 54 0.58 55
Insulating layer (mm) 40 60 80 100 120 140 21/20 31/30 2x21/20 2x31/30 21/20+ 31/30
24 24 24 25 24
GUTEX Thermofloor
Standard U-factor impact (W/m2K) noise level Lnw (dB) 0.69 0.51 0.40 0.33 0.28 0.25 1.06 51* 0.83 54 0.69 0.51 0.58
23 28
4. Concrete ceiling
New build and reconstruction
GUTEX Thermosafe-wd
GUTEX Thermofloor
Standard Impact U-factor impact sound at(W/m2K) noise level tenuation Lnw (dB) Lw (dB) 0.92 0.75 48* 0.63 0.47 0.38 0.32 0.27 0.24 0.92 0.75
U-factor (W/ m2K) 0.55 0.47 0.42 0.38 0.32 0.27 0.24
Standard Impact noise impact attentuation noise level Lw (dB) Lnw (dB) 52 26
GUTEX Thermosafe-wd
* Sill plates: OSB min. 22 mm; particleboard min. 25 mm; dry screed element min. 25 mm ** only in combination with sill plates in accordance with technical datasheet
Concrete ceiling
5. Beamed ceiling
New build and reconstruction
5. Beamed ceiling
New build and reconstruction
Insulating layer (mm) 40 60 80 100 120 140 21/20 31/30 2x21/20 2x31/30 21/20+ 31/30
GUTEX Thermosafe-wd
GUTEX Thermofloor
Installation height (mm) 90 110 130 150 170 190 70 80 90 110 100
Standard Impact noise U-factor impact attenuation (W/m2K) noise level Lw,H (dB) Lnw (dB) 0.64 0.48 0.38 0.32 0.28 0.24 0.94 0.76 79 10 0.64 0.48 0.55 75 10
Insulating layer (mm) 40 60 80 100 120 140 21/20 31/30 2x21/20 2x31/30 21/20+ 31/30
Installation height (mm) 90 110 130 150 170 190 70 80 90 110 100
Standard Impact U-factor impact noise at(W/m2K) noise level tenuation Lnw (dB) Lw,H (dB) 0.25 0.22 0.20 0.18 0.17 0.15 0.29 0.27 0.25 0.22 0.24
GUTEX Thermosafe-wd
50* 48*
11* 15*
GUTEX Thermofloor
Beamed ceiling
5. Beamed ceiling
New build and reconstruction
Insulating layer (mm) 40 60 GUTEX 80 Thermosafe-wd 100 120 140 21/20 31/30 GUTEX 2x21/20 Thermofloor 2x31/30 21/20+ 31/30
Installation height (mm) 90 110 130 150 170 190 70 80 90 110 100
Standard Impact noise U-factor impact attenuation 2 (W/m K) noise level Lw,H (dB) Lnw (dB) 0.24 0.21 0.19 0.18 0.16 0.15 0.27 0.26 0.24 0.21 0.23
Insulating layer (mm) 40 60 GUTEX 80 Thermosafe-wd 100 120 140 21/20 31/30 GUTEX 2x21/20 Thermofloor 2x31/30 21/20+ 31/30
U-factor (W/m2K) 0.63 0.48 0.38 0.32 0.28 0.24 0.94 0.76 0.63 0.48 0.55
62*
11*
60 (48*)
15
76 1) 76 1) 74 1) 74 1) 74 1)
15 1) 15 1) 17 1) 17 1) 17 1)
1) Calculated in accordance with wood information service, series 3 edition, part 3, sequence 3
5. Beamed ceiling
New build and reconstruction
Insulating layer (mm) 40 60 80 100 120 140 21/20 31/30 2x21/20 2x31/30 21/20+ 31/30
Standard U-factor impact (W/m2K) noise level Lnw (dB) 0,25 0,22 0,21 0,18 0,17 0,15 0,29 0,27 0,25 0,22 0,24
Insulating layer (mm) 40 60 GUTEX 80 Thermosafe-wd 100 120 140 21/20 31/30 2x21/20 GUTEX Thermofloor 2x31/30 21/20+ 31/30
U-factor (W/m2K) 0.24 0.21 0.19 0.18 0.16 0.15 0.27 0.26 0.24 0.21 0.23
Thermosafe-wd
Thermofloor
54 1)
17 1)
57 1)
17 1)
* Only in combination with 50 mm of limescale ballast below GUTEX Thermofloor ** only if PBP is mounted to sprung rod
1) Calculated in accordance with wood information service, series 3 edition, part 3, sequence 3
Beamed ceiling
57 1) 57(48*)1) 54 1) 54 1)
15 1) 15 1) 17 1) 17 1)
57 1) 57 (48*) 57 1) 57 1)
15 1) 14** 17 1) 17 1)
5. Beamed ceiling
New build and reconstruction
Standard U-factor impact (W/m2K) noise level Lnw (dB) 0.82 0.68 0.58 0.45 0.36 0.31 0.26 0.23 0.82 0.68
Standard Impact noise U-factor impact attenuation 2 (W/m K) noise level Lw,H (dB) Lnw (dB) 0.28 0.26 0.25 0.22 0.20 0.18 0.16 0.15 0.28 0.26
GUTEX Thermosafe-wd
GUTEX Thermosafe-wd
GUTEX Thermofloor
6 1)
GUTEX Thermofloor
50** 65 1)
9** 6 1)
** Only in combination with a 25 mm dry screed element from Fermacell and if limescale ballast is 50 mm
1) Calculated in accordance with wood information service, series 3 edition, part 3, sequence 3
5. Beamed ceiling
New build and reconstruction
GUTEX Thermosafe-wd
GUTEX Thermofloor
6 1)
* Only in combination with a 25 mm dry screed element from Fermacell 1) Calculated in accordance with wood information service, series 3 edition, part 3, sequence 3
Beamed ceiling
GUTEX Thermosafe-wd
Standard U-factor impact (W/m2K) noise level Lnw (dB) 0.26 0.25 65* 0.23 0.21 0.19 0.17 0.16 0.15 0.26 67* 0.25 69 1)
57**
5. Beamed ceiling
New build and reconstruction
Standard Impact U-factor impact noise at(W/m2K) noise level tenuation Lnw (dB) Lw,H (dB) 0.23 0.21 0.20 0.19 0.17 0.17 0.15 48* 11*
GUTEX Thermosafe-wd
Insulating layer (mm) GUTEX Thermosafehomogen 160 180 200 220 240
GUTEX Thermosafehomogen
Insulating layer (mm) 100 120 140 160 180 200 220 240
U-factor (W/m2K) 0.17 0.15 0.14 0.13 0.12 0.11 0.11 0.10
Phase shift (h) 16.2 17.3 18.4 19.6 20.7 21.9 23.0 24.2
Use of the insulated top floor ceiling in combination with Thermosafehomogen is not suitable for residential purposes.
Exterior panelling 1 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 18 mm GUTEX Multiplex-top 120 mm GUTEX Thermosafe-homogen Structure 1 18 mm formwork 100 mm rafters 15 mm timberboard 100 mm rafters 9.5 mm PBP 12 mm timberboard 100 mm rafters 10 mm GF 12 mm timberboard 100 mm rafters 15 mm GF 2 x 12.5 mm GF 15 mm timberboard 100 mm rafters 4 x 10 mm GF 15 mm timberboard 100 mm rafters 2 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 18 mm GUTEX Multiplex-top 280 mm GUTEX Thermosafe-homogen 3 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 60 mm GUTEX Ultratherm 120 mm GUTEX Thermosafe-wd
4
Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 60 mm GUTEX Ultratherm 240 mm GUTEX Thermosafe-wd
2 F 30 Interior panelling
5 F 90
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-SAC 02/III-370 and report no. 1753849-1.
Exterior panelling 1 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 50 mm Ultratherm Structure 1 140 mm rafters + insulation 24 mm rafters 12.5 mm PBP or PF 140 mm rafters + insulation 15 mm timberboard 12.5 mm PBP or PF 140 mm rafters + insulation 24 mm rafters 18 mm formwork 140 mm rafters + insulation 40 mm Thermosafe-wd 24 mm rafters 18 mm formwork 140 mm rafters + insulation 40 mm Thermosafe-wd 24 mm rafters 12.5 mm PBP or PF 140 mm rafters + insulation 24 mm rafters 60 mm Thermowall-gf 5 mm plaster 140 mm insulation: RW,R = 43 dB 200 mm insulation: RW,R = 44 dB 300 mm insulation: RW,R = 45 dB 140 mm insulation: RW,R = 45 dB 200 mm insulation: RW,R = 46 dB 300 mm insulation: RW,R = 47 dB 140 mm insulation: RW,R = 48 dB 200 mm insulation: RW,R = 50 dB 300 mm insulation: RW,R = 50 dB 140 mm insulation: RW,R = 46 dB 200 mm insulation: RW,R = 49 dB 300 mm insulation: RW,R = 49 dB 140 mm insulation: RW,R = 46 dB 200 mm insulation: RW,R = 48 dB 300 mm insulation: RW,R = 49 dB 2 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 120 mm Ultratherm 3 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 22 mm Multiplex-top 4 Concrete roofing tiles 30 mm support battens 40/60 mm counter battens 35 mm Multiplex-top
4 F 30
140 mm insulation: RW,R = 46dB 200 mm insulation: RW,R = 47 dB 300 mm insulation: RW,R = 48 dB
Interior panelling
140 mm insulation: RW,R = 49 dB 200 mm insulation: RW,R = 51 dB 300 mm insulation: RW,R = 51 dB 140 mm insulation: RW,R = 47 dB 200 mm insulation: RW,R = 49 dB 300 mm insulation: RW,R = 50 dB
140 mm insulation: RW,R = 48 dB 200 mm insulation: RW,R = 51 dB 300 mm insulation: RW,R = 51 dB 140 mm insulation: RW,R = 46 dB 200 mm insulation: RW,R = 48 dB 300 mm insulation: RW,R = 49 dB
140 mm insulation: RW,R = 48 dB 200 mm insulation: RW,R = 50 dB 300 mm insulation: RW,R = 51 dB 140 mm insulation: RW,R = 46 dB 200 mm insulation: RW,R = 48 dB 300 mm insulation: RW,R = 49 dB
140 mm insulation: 140 mm rafters + insulation RW,R = 45 dB 15 mm timberboard 200 mm insulation: 60 mm Thermowall-gf or TherRW,R = 46 dB moroom 300 mm insulation: 5 mm plaster RW,R = 47 dB 140 mm rafters + insulation 27 mm sprung rod 15 mm timberboard 15 mm PF 2 x 12.5 mm GF 140 mm rafters + insulation 27 mm sprung rod 15 mm timberboard 4 x 12.5 mm GF
8 F 90
140 mm insulation: RW,R = 56 dB 200 mm insulation: RW,R = 58 dB 300 mm insulation: RW,R = 59 dB Fire and noise insulation
Exterior panelling F90 GUTEX plaster system d 7 mm Thermowall d 100 mm RW,R = 44 dB RW,R = 44 dB RW,R = 44 dB RW,R = 44 dB RW,R = 46 dB RW,R = 47 dB RW,R = 50 dB Thermowall-gf d 60 mm (bolted) RW,R = 44 dB RW,R = 44 dB RW,R = 44 dB RW,R = 44 dB RW,R = 45 dB RW,R = 46 dB RW,R = 48 dB Thermowall-gf d 40 mm (bolted) Non-flammable panelling d 12.5 mm RW,R = 40 dB RW,R = 40 dB RW,R = 40 dB RW,R = 40 dB RW,R = 41 dB RW,R = 42 dB RW,R = 45 dB
Position
2 HWP* d 15 mm HWP* d 12 mm HWP* d 12 mm PBP board d 12.5 mm Plaster fibreboard d 12.5 mm Inst. level Variant A Inst. level Variant B Plaster fibreboard d 12.5 mm PBP board d 18 mm
Interior panelling
F30
BPB board d 9.5 mm Plaster fibreboard d 10 mm BPB board d 9.5 mm Plaster fibreboard d 12.5 mm Plaster fibreboard d 12.5 mm PBP board d 18 mm
F90
RW,R = 41 dB RW,R = 41 dB
RW,R = 46 dB RW,R = 46 dB
RW,R = 45 dB RW,R = 45 dB
RW,R = 41 dB RW,R = 41 dB
Installation level Variant A: with GUTEX Thermoinstal Installation level Variant B: with battens 60x60 mm and bay insulation 40 mm
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-SAC 02/III-321.
Position
2 HWP d 15 mm HWP d 12 mm HWP d 12 mm PBP board d 12.5 mm Plaster fibreboard d 12.5 mm Inst. level Variant A Inst. level Variant B Plaster fibreboard d 12.5 mm PBP board d 18 mm
Interior panelling
BPB board d 9.5 mm Plaster fibreboard d 10 mm HWP d 15 mm Plaster fibreboard d 12.5 mm Plaster fibreboard d 12.5 mm PBP board d 18 mm F90 F30
Installation level Variant A: with GUTEX Thermoinstal Installation level Variant B: with battens 60x60 mm and bay insulation 40 mm
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-SAC 02/III-321. Available for download at www.gutex.de
Position 1 2 Position 1 BPB board d 9.5 mm BPB board d 12.5 mm Plaster fibreboard d 12.5 mm Interior panelling F30 BPB board d 9.5 mm Plaster fibreboard d 10 mm HWP d 15 mm Plaster fibreboard d 12.5 mm Plaster fibreboard d 12.5 mm PBP board d 18 mm 2 HWP d 15 mm HWP d 12 mm HWP d 12 mm PBP board d 12.5 mm Plaster fibreboard d 12.5 mm Inst. level Variant A Inst. level Variant B Plaster fibreboard d 12.5 mm PBP board d 18 mm 3 BPB board d 9.5 mm Plaster fibreboard d 12.5 mm HWP d 15 mm HWP d 15 mm
Exterior panelling F90 GUTEX plaster system d 7 mm Thermowall-gf d 60 mm RW,R = 35 dB RW,R = 35 dB RW,R = 35 dB RW,R = 35 dB RW,R = 35 dB RW,R = 37 dB RW,R = 40 dB Thermowall d 100 mm RW,R = 38 dB RW,R = 38 dB RW,R = 38 dB RW,R = 38 dB RW,R = 38 dB RW,R = 40 dB RW,R = 43 dB Rear-ventilated facade/facade not rear-ventilated (bolted) d 14 mm Ultratherm d 120 mm RW,R = 45 dB RW,R = 45 dB RW,R = 45 dB RW,R = 45 dB RW,R = 45 dB RW,R = 47 dB RW,R = 50 dB Multiplex-top d 20 mm Thermosafehomogen d 120 mm RW,R = 45 dB RW,R = 45 dB RW,R = 45 dB RW,R = 45 dB RW,R = 45 dB RW,R = 47 dB RW,R = 50 dB
F90
RW,R = 35 dB RW,R = 35 dB
RW,R = 38 dB RW,R = 38 dB
RW,R = 45 dB RW,R = 45 dB
RW,R = 45 dB RW,R = 45 dB
Installation level Variant A: with GUTEX Thermoinstal Installation level Variant B: with battens 60x60 mm and bay insulation 40 mm
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-SAC 02/III-321.
Plastered facade
Rear-ventilated facade
The structure can be composed with one variant of the individual layers.
Exterior panelling Layer 1 Mineral render d 6 mm Layer 2 GUTEX Thermowall-gf d 40 mm 210 kg/m GUTEX Thermowall d 80 mm 160 kg/m GUTEX Multiplextop d 28 mm 200 kg/m GUTEX Ultratherm d 40 mm 190 kg/m
Support structure
Bay insulation Layer 1 GUTEX Thermoflex d 140 mm 30 kg/m or Cellulose insulation (Isofloc or Dmmstatt) d 140 mm 45 kg/m or Mineral wool, fusion point 1000C d 140 mm 30 kg/m or Glass wool d 140 mm 18 kg/m Timberboard d 15 mm 550 kg/m
Interior panelling Layer 2 Installation level Optional Layer 3 PB d 9.5 mm or PB d 95 mm or plaster fibreboard (Xella,Knauf, Rigips) d 10 mm Timberboard d 12 mm 550 kg/m Plaster fibreboard (Xella,Knauf, Rigips) 12.5 mm Installation level Optional PB d 12.5 mm or PB d 12.5 mm or Plaster fibreboard (Xella,Knauf, Rigips) d 12.5 mm Plaster fibreboard (Xella,Knauf, Rigips) d 10 mm
Mineral render d 6 mm
Rear-ventilated facade
Rear-ventilated facade
Facing structures for outside wall can be combined with the facing structures for inside wall
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-SAC 02/III-321.
Variant 2:
The structure can be composed with one variant of the individual layers Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/m) 500 500 500 500 500 500
Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12.5 + 10 Raw density (kg/m) 500 500 500
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/m) 35 80 45 30 18
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/m) 35 80 45 30 18
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product GUTEX Thermowall-gf + Render layer Thickness (mm) 60 6 Raw density (kg/m) 210 700
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product GUTEX Thermowall-gf + Render layer Thickness (mm) 60 6 Raw density (kg/m) 210 700
Installation level in accordance with general building inspection certificate no. P-172 34405-ift.
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-172 34405-ift.
Variant 3:
Joint
Variant 4:
The structure can be composed with one variant of the individual layers Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/m) 35 80 45 30 18
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/ m) 35 80 45 30 18
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product PBF/PF/cement-bonded chipboard + GUTEX Thermowall-gf + render layer Thickness (mm) Raw density (kg/m)
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product Xella HD board + GUTEX Thermowall-gf + Render layer Thickness (mm) 15 40 6 Raw density (kg/m) 210 700
12.5 40 6
210 700
Joint 60 mm:
Product GUTEX Thermoflex Mineral wool, fusion point 1000C Glass wool Thickness (mm) 40 40 40 Raw density (kg/m) 35 Fire and noise insulation 30 18
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-172 34405-ift.
Variant 6:
The structure can be composed with one variant of the individual layers Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/ m) 35 80 45 30 18
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/ m) 35 80 45 30 18
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product PBF/PF/cement-bonded chipboard + GUTEX Thermowall-gf Thickness (mm) 12.5 60 Raw density (kg/ m)
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product Xella HD board + GUTEX Thermowall-gf Thickness (mm) 15 60 Raw density (kg/m)
210
210
Joint 60 mm
Joint 60 mm
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-172 34405-ift.
Variant 8:
The structure can be composed with one variant of the individual layers Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/ m) 35 80 45 30 18
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/ m) 35 80 45 30 18
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product MDF + GUTEX Thermowall-gf + render layer Thickness (mm) 15 40 6 Raw density (kg/ m) 210 700
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product MDF + GUTEX Thermowall-gf Thickness (mm) 15 60 Raw density (kg/ m) 210
Joint 60 mm
Joint 60 mm:
Product GUTEX Thermoflex Mineral wool, fusion point 1000C Glass wool Thickness (mm) 40 40 40 Raw density (kg/ m) 35 Fire and noise insulation 30 18
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-172 34405-ift.
Variant 10:
The structure can be composed with one variant of the individual layers Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Interior panelling:
Product PBF Timberboard + PF PF + PF Thickness (mm) 18 12 + 15 12.5 + 10 500 Raw density (kg/ m)
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 160 160 160 160 160 Raw density (kg/ m) 35 80 45 30 18
Bay insulation:
Product GUTEX Thermoflex GUTEX Thermosafe-homogen Cellulose insulation Mineral wool, fusion point 1000C Glass wool Thickness (mm) 80 80 80 80 80 Raw density (kg/ m) 35 80 45 30 18
Construction: Solid construction timber min. 160 x 60 mm, a 62.5 cm Exterior panelling:
Product PF + PF PBF + PBF Thickness (mm) 15 + 15 18 + 18 Raw density (kg/ m) 500 500
Joint 40 mm
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-172 34405-ift.
Variant 12:
The structure can be composed with one variant of the individual layers Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Interior panelling:
Product Timberboard + PB Timberboard + PBF Timberboard + PF Timberboard + PB Timberboard + PBF Timberboard + PF PF + PF Thickness (mm) 15 + 9.5 15 + 9.5 15 + 10 12 + 12.5 12 + 12.5 12 + 12.5 12.5 + 10 Raw density (kg/ m) 500 500 500 500 500 500
Thickness (mm) 15 + 15 60 18 + 18 60
Joint 50 mm
Joint 50 mm
Further detailed information on applications, fastening systems for the materials to be used, structural analyses, connections and fittings can be found in the general building inspection certificate no. P-172 34405-ift.
Insulation against the heat in summer GUTEX wood insulation boards protect living areas from high temperatures, in particular, areas under roofs. Thanks to their high thermal storage capacity, they effectively dampen the flow of warmth from exterior to interior areas. Wood has a specific thermal storage capacity of 2100 J/kgK, which is the highest amongst all insulation materials. Insulation against the cold in winter Effective insulation reduces heating bills and creates a comfortable living environment in winter. Due to their low thermal conductivity (D = 0.037 W/mK), GUTEX insulating wood fibreboards provide optimum insulation in winter, protecting the interior of houses from heat loss and ingression of cold. Pleasant indoor environment GUTEX wood fibre insulation boards are vapour permeable ( = 3), regulating the living environment with their ability to absorb and release up to 15 % of their weight in moisture without the loss of their insulation capacity. Acoustic insulation The open-pore structure of GUTEX wood fibreboards and their high absorption volume contribute to their ability to deliver superb soundproofing against airborne and impact noise. Fire protection GUTEX wood fibre insulation boards easily comply with fire protection regulations. Various individual certificates of approval are available for F30-B to F90-B fire resistance ratings for roof and wall structures. Environmental compatibility The raw material for all GUTEX insulation boards comes from wood that is locally harvested and
grown using sustainable forestry management practices. GUTEX exclusively uses untreated spruce and fir chips and shavings, which are by-products obtained from other timber manufacturing processes. All GUTEX insulation boards are tested and certified as biologically safe and compatible with other building materials (natureplus seal of quality). Recyclability GUTEX wood fibreboards are completely recyclable and, provided wood preservatives have not contaminated them, can be disposed of at the nearest recovery centre. User friendly GUTEX insulation boards are manufactured according to the highest quality standards and are characterised by absolutely minimum dimensional deviation. This, combined with the detailed installation instructions provided by the manufacturer, makes working with GUTEX products a pleasure. Made in Germany For more than 80 years, GUTEX, a family owned and operated company, has manufactured insulation boards at its plant in Waldshut-Tiengen, which is located in the southern Black Forest. All GUTEX insulation boards carry the CE and U marks and are produced according to the current applicable standards.GUTEXs external thermal insulation system (ETICS) is approved by the German building authorities. GUTEX customer service An important part of GUTEXs customer service is its qualified assistance. Whether you require help with a private single-family house or commercial property, GUTEXs trained and qualified staff will gladly assist you.If you have technical queries, please contact our technical assistance department by phone +49-7741/60 99-125, fax +49-7741/60 99-21 or per e-mail at anwendungstechnik@gutex.de. GUTEX product training Architects, craftsmen, wholesalers, sales staffs and developers can benefit from the workshops GUTEX offers, which address specific topics, including physics and building, construction techniques, product applications, etc.Visit our Web site for further information or give us a call.
GUTEX Holzfaserplattenwerk | Gutenburg 5 | D-79761 Waldshut-Tiengen | Tel: +49 7741/60 99-0 | Fax: +49 7741/60 99-57 | www.gutex.de | Email: info@gutex.de