Professional Documents
Culture Documents
Features
Available in sizes from 1/2" to 2" with sanitary clamp Flow rates from 0.1 to 250 gallons per minute (GPM) Temperature ranges up to 350 F (177 C) 316 stainless steel construction Magnetic or modulated carrier (RF) pickoffs available Exceptional repeatability of 0.1% NIST traceable calibrations Withstands clean-in-place (CIP) and sterilize-in-place (SIP) processes Compatible with all Flow Technology electronics Ceramic bearings for long life
Flowmeter Cut-Away
SA-24
Specifications
Repeatability Linearity
0.1% of reading 0.5% of reading over the normal 10:1 flow range Note: SA4-8 is 2% of reading 100 microns 510 mS to step change Less than 10 psi for max. flow in water 250 psig/17.2 bar g 350 F (177 C) 202000 Hz typical (depends on model) 3/4" clamp/0.98" O.D. 1-1/2" clamp/1.98" O.D. 2" clamp/2.51" O.D.
Maximum Particle Size Response Time Pressure Drop Max. Pressure Max. Temperature Frequency Range Sanitary Clamps T1 T2 T3
300 ft. (91 meters) without pre-amplifier DC coil resistance: 2275 ohms, nominal Minimum output voltage: 10 mV 30 ft. (9 meters) maximum to carrier amplifier 12 ohms, nominal
Modulated Carrier Transmission distance: DC coil resistance: MS Connector 2-pin, standard pickoff: 3-pin, amplified pickoff:
Tapered End Fittings The I.D. of the Flow Technology sanitary meters are designed with a taper in the end fitting to provide a smooth transition from the meter bore to standard size mating tubing. The standard Tapered to Line Size is provided in the Model Numbering System chart.
SIP Considerations
Surface Finish
Bore Internals
Dimensions
Standard Configuration
U T N L K F
Used On Line Size Clamp Size Code
45 .039 .036 .302 .300 2.450 .988 .980 .037 .035 SA4-8 .5"
45 .012 .009 .372 .370 2.450 .988 .980 .037 .035 SA6-8
45 .092 .089 .442 .440 2.450 .988 .980 .037 .035 SA-08 .75"
45 .187 .184 .504 .502 3.250 1.988 1.980 .035 .030 SA-10
45 .030 .027 1.317 1.315 4.590 1.988 1.980 .052 .048 SA-24
45 .059 .056 1.753 1.751 6.060 2.520 2.512 .072 .068 SA-332 2" 2" T3
1.988 1.988 1.988 1.980 1.980 1.980 .035 .030 SA-12 1" 1.5" T2 .045 .037 SA-16 .049 .044 SA-20
1.5"
.75" T1
Optional Configuration
U T N L K F
Used On Line Size Clamp Size Code
45 .030 .026 .504 .502 3.25 .988 .980 .035 .030 SA-10
45 .030 .026 .565 .563 3.25 .988 .980 .035 .030 SA-12
60 .166 .163 .302 .300 2.450 1.988 1.980 .037 .035 SA4-8
60 .144 .141 .372 .370 2.450 1.988 1.980 .037 .035 SA6-8 1" 1.5" T2
60 .110 .107 1.002 1.000 4.06 2.520 2.512 .049 .044 SA-20 2" 2" T3
60 .163 .160 1.317 1.315 4.59 2.520 2.512 .052 .048 SA-24
1.988 2.520 1.980 2.512 .037 .035 SA-08 .045 .037 SA-16
.75" .75" T1
Normal 10:1 Nominal Extended Flow Range Size Flow Range Max Freq. GPM LPM RF MIN MAG MIN All MAX Hz MIN MAX MIN MAX GPM LPM GPM LPM GPM LPM
.25 .50 2.50 5.00 .95 9.50 .10 .15 .25 .38 .57 .95 .12 .20 .3 .4 .5 1.0 1.5 2.5 3.5 .45 .76 1.1 1.5 1.9 3.8 5.7 9.5 13.2 3 5 10 15 25 60 100 160 250 11 19 38 57 95 227 380 606 946 2000 2100 2000 2000 2000 2000 1950 1500 1300
T1 = .75" T2 = 1.5" T1 = .75" T2 = 1.5" T1 = .75" T2 = 1.5" T2 = 1.5" T1 = .75" T2 = 1.5" T1 = .75" T2 = 1.5" T3 = 2.0" T2 = 1.5" T3 = 2.0" T2 = 1.5" T3 = 2.0" T3 = 2.0" -
0.5" 1.0" 0.5" 1.0" .75" 1.0" 1.0" .75" 1.0" .75" 1.0" 2.0" 1.5" 2.0" 1.5" 2.0" 2.0"
1.90 19.00
1.00 10.00 3.80 38.00 1.25 12.50 4.70 47.0 2 5 9 15 22 20 50 90 150 225 7.60 76.0 19 34 57 83 190 340 570 830
.30 1.10 .50 1.90 1.0 1.0 1.6 2.5 3.8 3.8 6.1 9.5
Special Designator
Special designator to be assigned by factory when required. Examples: 316 L SS, special tapering or other special modifications.
Pickoff
1 = RF, 2-pin connector 2 = Magnetic, 2-pin connector 5 = RF, 1/2" NPT for mounting electronics 3 = Magnetic, 1/2" NPT for mounting electronics
Calibration Range
N = 10 points normal 10:1 X = 10 points extended Y = 20 points extended
Calibration Fluid
W = Water B = Viscosity blend
Journal Bearings
G = Ceramic
Calibration Units
= Standard U = Units other than GPM R = Range other than normal or extended B = Both units and range other than standard
Materials of Construction
Code E H Housing 316SS 316SS Rotor 430F 17-4*
Fluid Type
L = Liquid * Non-Standard
Specifications are for reference only and are subject to change without notice.
Local Representative:
8930 S. Beck Ave., Ste 107, Tempe, Arizona 85284 USA Tel: (480) 240-3400 Fax: (480) 240-3401 Toll Free: 1-800-528-4225 E-mail: ftimarket@ftimeters.com Web: www.ftimeters.com DB 62046 Rev E 2004 FTI Flow Technology, Inc. Printed in USA