Professional Documents
Culture Documents
Com
Design of an Anchor Block Type 2 Model of Type 2 Anchor Block: Example: Anchor block of Chandra Jyoti MHP, Kavre H1 = 1.3 m L = 1.0 m w = 0.9 m Z = 0.3 m h1 = 0.6 m h2 = 0.3 m X = 0.6 m i = 10 lc = 0.3 m hc = 0.2 m = 10 = 35 Pipe Diameter, d = 130 mm Pipe Thickness, t = 4 mm Discharge, Q = 20 lps Gross Head, hgross = 42 m Surge Head, hsurge = 95 m Distance to u/s support pier, L2u = 4m L1u = 2 m Distance to d/s support pier, L2d = 4m L1d = 2 m Distance to u/s expansion joint = 18m L4u = 18 m Number of piers at upstream = 4 Relation Used for Area Calculation: A1 H1N A2 H2(L N) A3 1 N(H2 + M H1) 2 A4 1 M(L N) 2 Relation Used for Centre of Gravity Calculation: X1 1 N 2 X2 1 (L + N) 2 X3 2 N 3 X4 1 (L + 2N) 3 Relation Used for Calculating Deduction Volume Occupied by Penstock: Vp lu (du + 2t)2 + ld (dd + 2t)2 4 4 Where d + 2t Y = H1 Z X tan 2 cos d + 2t H2 = Y (L X)tan + +Z 2 cos d + 2t 5Z M = Y H2+[ + ]sin 2 cos (90 ) 3 1.08 m2 0.16 m2 0.03 m2 0.04 m2
Manual for Anchor Block, Saddle Support & Machine Foundation Design Aids 2004, Prepared By Pabitra Gurung
Prarup.Com
N = X +[
=
N = 0.83 m
= 67.5
lu = 0.61 m ld = 0.49 m
Further Design Procedure for the Block, Total head, htotal = hgross + hsurge Block volume excluding pipe volume, (V)
= 42 + 95 = 137 m = w (A1 + A2 + A3 + A4 lc hc) Vp = 0.9 (1.08 + 0.16 + 0.03 + 0.04 0.3 0.2) 0.02 m3 = 1.10 m3 = 22 kN/m3 = V concrete = 1.10 22 = 24.20 kN = 77 kN/m3 = (d + t )t steel = 0.134 0.004 77 = 0.13 kN/m = 9.81 kN/m3 d 2 water 4 (0.13) 2 = 9.81 4 = 0.13 kN/m = = 0.26 kN/m
WP + WW Calculation for relevant forces: 1. F1u = (WP + WW ) L1u cos = 0.26 2 cos 10 2. F1d = (WP + WW ) L1d cos = 0.26 2 cos 35
= 0.51 kN
= 0.43 kN
3. Frictional force per support pier: = f (WP + WW ) L2u cos Where f = 0.6 for steel on concrete = 0.6 0.26 4 cos 10 = 0.61 kN per support pier
Manual for Anchor Block, Saddle Support & Machine Foundation Design Aids 2004, Prepared By Pabitra Gurung
Prarup.Com
Since there are 4 support piers then, F2u = 0.61 4 = 2.46 kN Note that F2d is zero since an expansion joint is located immediately downstream of the anchor block. 4. F3 = 2 water htotal
5. F4u
= WP L4u sin = 0.13 18 sin 10 = 0.41 kN But F4u is insignificant since a is less than 20 and could have been ignored. F4u 0 F4d is negligible since an expansion joint is placed immediately downstream of the anchor block, i.e., L4d 0 and therefore F4d 0
6. F5 = EaT (d + t )t Since the expansion joint is installed between the blocks, F5 =0 7. F6 = 100d = 100 0.13
= 13 kN
8. F7 F7u
= water htotal (d + t )t = 9.81 (137 18 sin ) 0.134 0.004 = 2.21 kN F7d = 9.81 137 0.134 0.004 = 2.26 kN Note that as discussed earlier the resultant of these forces is insignificant.
9. F8
= water htotal
11. Soil force, F10 Unit weight of concrete, (?soil) For stiff clay and stiff sandy clay ()
= 20 kN/m3 = 30 3
Manual for Anchor Block, Saddle Support & Machine Foundation Design Aids 2004, Prepared By Pabitra Gurung
Prarup.Com
Ka
= 0.355
h F10 = K a w soil 1 cos i 2 But in this example, h1 h2 = 0.6 0.3 = 0.3 < 1, So F10 is insignificant, therefore F10 = 0
Resolution of forces: = 10, = 35 Forces (kN) X component (kN) + Y component (kN) + F1u = 0.51 + F1u cos = + 0.50 F1u sin = 0.09 F sin = 0.25 + F1u cos = + 0.35 F1d = 0.43 1u F2u sin = 0.43 F2u cos = 2.42 F2u = 2.46 Negative during 1expansion Negative during 1expansion Positive during 2contraction Positive during 2contraction + + F3 cos + F3 sin F3 = 7.72 = + 2.95 = 7.13 2 2 F6 (cos cos ) = 2.15 F6 (sin sin ) = 5.20 1 F6 = 13 Positive during expansion Positive during 1expansion Negative during 2contraction Negative during 2contraction F7u = 2.21 + F7u sin = + 0.38 + F7u cos = + 2.18 F7d cos = 1.85 F7d sin = 1.30 F7d = 2.26 + + + F8 sin F8 cos F8 = 0.01 0 = 0.01 2 2 WB = 24.20 0 + 24.20 1 H = + 2.67 Expansion V = + 21.76 1Expansion SUM 2 H = + 3.21 Contraction V = + 12.22 2Contraction Note that forces are positive in X-direction is towards the right and Y-direction downwards. Sum of horizontal forces that act at the bend, 1 Expansion case 2 Contraction case Sum of vertical forces that act at the bend,
1 2
= + 2.67 kN = + 3.21 kN
Calculate for the centre of gravity of the block from the upstream face of the block taking the moment of mass. The effect of the pipe passing through the block is considered negligible, so need not be calculated. Ai X i w concrete X = Ai w concrete 1.08 0.42 + 0.16 0.92 + 0.03 0.55 + 0.04 0.89 0.3 0.2 0.15 = = 0.51 m 1.08 + 0.16 + 0.03 + 0.04 0.3 0.2
The weight of the block WB acts 0.51 m from point O.
Manual for Anchor Block, Saddle Support & Machine Foundation Design Aids 2004, Prepared By Pabitra Gurung
Prarup.Com
A force diagram on the block is as shown in Figure; Checking for Safety of the Block: 1. Checking safety against overturning
1
Expansion Case
Taking sum of moment about point O with clockwise moments as positive: M at O, = 24.20 0.51+2.67 0.82 2.44 0.60 = 13.06 kN-m M 13.06 = 0.60 m = V 21.76 L M = 0.50 0.60 = 0.1 e= 2 V L 1 eallowable = base = = 0.17 6 6 e < eallowable OK
2
Contraction Case
Taking sum of moment about point O with clockwise moments as positive: M at O, = 24.20 0.51+3.21 0.82 11.96 0.60 = 7.80 kN-m M 7.80 = = 0.64 m V 12.22 L M = 0.50 0.64 = 0.14 e= 2 V L 1 eallowable = base = = 0.17 6 6 e < eallowable OK Since e < eallowable for both cases, the structure is safe against overturning. 2. Checking safety on bearing capacity For stiff clay allowable bearing pressure is 200 kN/m2
1
Expansion Case
Pbase =
V Abase
6e 1 + L base
OK
Manual for Anchor Block, Saddle Support & Machine Foundation Design Aids 2004, Prepared By Pabitra Gurung
Prarup.Com
2
Contraction Case
Pbase =
V Abase
6e 1 + L base
OK
In both cases Pbase < Pallowable = 200 kN/m2, the structure is safe against sinking. 3. Checking safety against sliding
1
Expansion Case
Contraction Case
3.21 kN < 0.5 12.22 kN 3.21 kN < 6.11 kN OK Since, H < V in both cases the structure is safe against sliding. The anchor block is stable.
Manual for Anchor Block, Saddle Support & Machine Foundation Design Aids 2004, Prepared By Pabitra Gurung