Professional Documents
Culture Documents
FS-507
Finisher
Applied Machine:
NOTE Before installing, be sure to unplug the power cord of the machine. Keep all packing materials out of the reach of children.
4683-7732-01
4684U058AA
9 Label ......................................................................................................1 <Machine + Paper Feed Cabinet PC-402> 10 Screws A ................................................................................................3 11 Screws B ................................................................................................2 12 Installation manual (this manual) ...........................................................1 13 Spacer ....................................................................................................1 1 2 3 4
4684U059AA
<Machine + Desk>
4684U061AB
4684U062AA
4683IXC505DA
4683IXC504DA
4698U047AA 4684U060AA
4698U048AA
4684U075AA
4684U070AA
10
11
12
13
4683IXC501DA
4684U072AA
9735U001AA
4583U018AA
FS-507
2. Remove all tape and packing brackets. Tape NOTE Make sure that the installation site is flat and level. After the Finisher has been set up, avoid moving it unless it is absolutely necessary. When the Finisher needs to be moved, perform the steps by referring to Removing the Rail on p. 6. After the Finisher has been moved, perform the steps given in Installing the Horizontal Transport Unit on p. 3 and step 5, 6 on p. 4.
Packing bracket
4683IXC001DA
4643U004AD
C4683U004AA
Packing bracket
4643U003AA
4683U013AA
Tape
C4651U023AB 4583U016AA
C4683U023AA
C4683U009AA
2. Push the horizontal transport unit in. NOTE Make sure that the gears on the horizontal transport unit and on the finisher are correctly aligned.
3. Place the Ground Plate furnished with the kit in Rail Guide.
C4683U014AA
4684U063AB
3. Secure the horizontal transport unit with the lock. NOTE Firmly secure the Horizontal Transport Unit and the Finisher in position using the Lock Lever.
C4683U013AA 4684U064AA
4. Attach the rail guide to the left side of the Paper Feed Unit as shown in the illustration (two screws B furnished with the finisher). NOTE Fit Rail Guide in the tab on the lower portion of the Paper Feed Unit.
4684U065AA
If the finisher is not at the same height as the machine, adjust the machine as follows.
7. Insert the spacer that comes with the finisher into the rail. NOTE Slide out the rail to the left and check that it does not come off the Rail Guide.
4643U021AB
2. Slide the finisher away from the machine, and then remove the lower-front cover (two screws) of the finisher.
4583U017AB
8. Slide the other end of the rail installed in step 5 into the rail guide on the finisher. NOTE Insert the rail until it snaps into place. At this time, the finisher should stay attached to the machine, even if you try to pull it away.
C4683U010AA
3. Lift the finishers two caster covers up, and then pull them off.
4643U020AA
C4683U011AA
1. Remove the connector covers from the horizontal transport unit and the machine. 2. Connect the hookup cord to the horizontal transport unit and the machine.
4683IXE003DA
4643U022AB
3. Secure the hookup cord of the Horizontal Transport Unit using the cord clamp (large) of the finisher.
5. If the finisher tilts toward the machine, check the following: a Are distances a and b equal? b *
4684U067AA
If a and b are not equal, refer to step 4 above and turn the adjusting bolt (lower bolt) as indicated to adjust the tilt of the finisher.
6. After the adjustment is finished, without turning any of the adjusting bolts (lower bolts), tighten the four securing bolts (upper bolts). 7. Re-install the caster covers and the lowerfront cover (two screws).
4643U029AA
4643U024AA
C4683U018BA
4698U109AA
for Machine
4643U017AA
for ADF 1. Pinch together the rail stoppers on the left side of the finisher to release them. 2. Disconnect the two hookup cords. 3. Remove the horizontal transport unit from the finisher, and then place it on top of the machine. 4. Carefully pull the finisher away from the machine. 5. Slide the rail under the machine, and then remove it from the right side of the machine.
4683IXC501DA
C4651U020AA
4643U031AA
2. Tighten the securing screw. 4. Touch 2-Hole so that its background changes to black.
4037IXC175DA
3. Close the upper cover. 4. Make another test print, and then check that the punched holes are aligned. NOTE If the punched holes are not at their standard positions, adjust the holepunching position.
4583IXE507DA
4643U031AA
5. Load an A4 crosswise or Letter crosswise document (blank sheets of paper may be used) in the document feeding tray. 6. Press the Start key.