Professional Documents
Culture Documents
-V- New
Bellows DADB Standard cylinders DNC, ISO 15552
Key features At a glance
DIN
Standards-based cylinders to ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA 24 562, NF E 49 003.1 and UNI 10290)
The modern design and construction save up to 11% on fitting space compared to ordinary standard cylinders, thus permitting a considerably more compact system design
An extensive range of accessories makes it possible to install the cylinder virtually anywhere The widest range of variants on the market provides the right DNC cylinder for every application
Cylinder with clamping units DNC-KP Piston rod can be held or clamped in any position Piston rod can be held in position for long periods even with alternating loads, fluctuating operating pressure or leaks in the system Cylinder with end-position locking DNC- -EL Mechanical locking when the end position is reached Lock is only automatically released when pressure is supplied to the cylinder End-position locking at one or both ends
DNCKE Suitable for use in safety-related control systems in compliance with EN 954-1, EN 1050, EN 292 and EN 983 Fail-safe Piston rod can be clamped in any position Cylinder/valve combination DNC-V1 V6 The cylinder/valve combination is assembled and fitted with tubing ready for connection Particularly suitable for decentralised use in larger systems
Tandem cylinder DNCT Connection of 2 cylinders with the same piston diameter and stroke in series Double the thrust and return force in comparison to a standard cylinder
Longer service life thanks to the bellows kit DADB The bellows kit is a leak-free system. To prevent unwanted media being drawn in, the supply and exhaust air must be ducted via a venting hole in the connection part 1. The kit protects the piston rod, seal and bearings from a wide range of media, for example: dust, chips, oil, grease, fuel.
Internet: www.festo.com/catalog/...
Description For working at both ends with the same force in the forward and return stroke, for attaching external stops Temperature resistance up to max. 120 C Suitable for slow stroke movements at a constant, stick-slip-free speed over the full stroke of the cylinder. Seal contains silicone grease (not free of paint-wetting impairment substances) Special seals considerably reduce system wear. This means a considerably lower response pressure. Seal contains silicone grease (not free of paint-wetting impairment substances) For supplying vacuum, small parts, media, etc. Metric standard thread to ISO Special spanner flats Ideal for use in welding environments: Protection against welding spatter Small working loads Harder surface compared to steel Long service life Integrated clamping unit on the piston rod Positive locking in the end position as a drop guard. If there is a drop in pressure, the piston rod is secured in its end position to prevent it from dropping Protection against rotation. For correctly oriented feeding All external cylinder surfaces comply with corrosion resistance class 3 to Festo standard 940 070. The piston rod is made from corrosion and acid-resistant steel The cylinder is equipped with a hard-chrome plated piston rod and a rigid wiper seal, which protects against dry, dusty media Temperature resistance down to max. 40 C
S11
S20 K2 K3 K5 K7 K8 K10
Through, hollow piston rod Extended male piston rod thread Female piston rod thread Special piston rod thread Piston rod with external hexagon Extended piston rod Smooth anodised aluminium piston rod
KP EL
Q R3
R8
TT
Low temperature
Internet: www.festo.com/catalog/...
[mm] Double-act Basic version ing DNC 32, 40, 50, 63, 80, 100, 125
[mm] 20, 25, 30, 40, 10 2,000 50, 60, 70, 80, 100, 125, 150, 160, 200, 250, 300, 320, 400, 500
Position sensing Q
S2/S20
K2
Standard hole pattern, with clamping unit DNC-KP 32, 40, 50, 63, 80, 100, 125 DNCKE 40, 63, 100
10 2,000 S2
10 2,000
Standard hole pattern, with end-position locking DNC--EL 32, 40, 50, 63, 80, 100
10 2,000 S2
Standard hole pattern, cylinder/valve combination DNC-V1 V6 32, 40, 50, 63, 80, 100
100 2,000
Standard hole pattern, tandem cylinder DNCT 32, 40, 50 63, 80, 100, 125
2 500 3 500
Internet: www.festo.com/catalog/...
Low temperature TT
Dust protection
Low friction
K8
K10
S6
S10
S11
R3
R8
V1 V6 9
25
DNCKE
dncke
33
40
dnct
Internet: www.festo.com/catalog/...
aF aE aF bF aG aH aJ aI bJ bA bB 2 3 4 bD bE
DNC--S2 bC Mounting attachments and accessories Brief description 1 2 3 Multi-position kit DPNC Foot mounting HNC/CRHNC Flange mounting FNC/CRFNG Trunnion flange ZNCF/CRZNG Trunnion support LNZG/CRLNZG Swivel flange SNC Clevis foot LSNG Clevis foot LSNSG For connecting two cylinders with identical piston diameters to form a multi-position cylinder For bearing or end caps For bearing or end caps Cannot be used on the bearing cap in combination with bellows kit DADB For bearing or end caps Cannot be used on the bearing cap in combination with bellows kit DADB For end caps With spherical bearing Weld-on, with spherical bearing
EL
V1 V6
1)
Page/ Internet 49 50 51
52
5 6 7 8
54 55 58 58
1) 1) 1)
1) 1) 1)
1) 1) 1)
Internet: www.festo.com/catalog/...
EL
V1 V6
1) 1) 1) 1) 1) 1)
Page/ Internet 57 58 57 56 58 58 53 59 58 59 59 59 59 59 59 64 64
bJ bA bB bC bD
2)
50 and above
65 65 66 quick star 60
bE bF bG bH bI
1) 2)
Not with variant S2 or S20 For piston 32, 40 mm only with variant R3
Internet: www.festo.com/catalog/...
DNC Type Double-acting DNC Piston [mm] Stroke [mm] Cushioning P PPV Position sensing A Without position sensing Via proximity sensor Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Standard cylinder
80
320
PPV
Note The standard cylinder DNC can be ordered using either a fixed part number and type designation or via the modular product system. The type code listed above only applies to the DNC standard cylinder with fixed part number and type designation. Variants can only be ordered using the modular product system.
Internet: www.festo.com/catalog/...
www.festo.com/en/ Spare_parts_service Wearing parts kits 24 DNC--A- With position sensing Standards-based cylinders to ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA 24 562, NF E 49 003.1 and UNI 10290)
DIN
General technical data Piston Pneumatic connection Piston rod thread K3 K5 Constructional design
40 G M12x1.25 M8 M12
Max. torsional backlash of piston rod [] Cushioning Cushioning length PPV Position sensing Type of mounting Mounting position
0.6
0.45
0.45
0.45
0.45
[mm]
Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 Via proximity sensor Via female thread Via accessories Any
22
32
32
42
Internet: www.festo.com/catalog/...
40
50
63
80
100
125
S6 TT R3
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 0.6 12 1.5 12 After 10 strokes 0.16 12 0.1 12 0.06 12 After 24 hours 0.3 12 0.2 12 0.1 12 1 12 20 +80 0 120 40 +80 2 3 Germanischer Lloyd Specified types www.festo.com
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
Force [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Max. impact energy at the end positions1)
1)
S2/S20 S2/S20
The permissible impact energy is reduced by approx. 10% for variants K10 and S20
vperm. =
Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
m load =
2 x E perm. m dead v2
10
Internet: www.festo.com/catalog/...
Fq
Internet: www.festo.com/catalog/...
11
s [mm]
s [mm]
Fq [N]
Fq [N]
l [mm] 50/63 Max. torque = 1,500 Nmm / Max. stroke = 500 mm 80/100
l [mm]
s [mm]
Fq [N]
s [mm] l [mm]
Fq [N]
l [mm]
Examples for piston 32 mm Example 1: Stroke length l = 150 mm Result: permissible Lateral force Fq = 9.5 N Lever arm s = 84 mm Example 2: Lateral force Fq = 40 N Result: permissible Stroke length l = 28 mm Lever arm s = 20 mm Example 3: Stroke length l = 150 mm Lever arm s = 20 mm Max. torque 800 Nmm Fq = Lever arm 100 mm =8N Result: permissible Fq = 8 N < Fqmax. = 9.5 N
Fq
12
Internet: www.festo.com/catalog/...
32 517 30 162 9
40 800 45 307 16
50 1,260 64 538 25
63 1,709 73 663 25
504 29 149 8
738 41 244 11
1,187 60 465 20
1,632 68 587 20
2,652 99 994 31
576 39 170 18
895 61 330 32
1,390 89 560 50
1,917 98 711 50
443 24 88 3
655 35 162 6
1,001 47 279 8
1,437 57 391 9
2,302 81 643 13
4,138 90 1,029 13
S2-K10 Through, smooth anodised piston rod Product weight with 0 mm stroke 514 Additional weight per 10 mm stroke 27 Moving load with 0 mm stroke Additional load per 10 mm stroke TT Low temperature Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke 108 6
766 40 201 11
1,181 56 351 17
1,676 65 470 17
2,701 94 787 26
520 31 108 9
876 46 204 16
1,279 65 363 25
2,112 73 460 25
TT-S2 Low temperature with through piston rod Product weight with 0 mm stroke 606 Additional weight per 10 mm stroke 40 Moving load with 0 mm stroke Additional load per 10 mm stroke 169 18
1,020 62 326 32
1,546 89 573 49
2,401 98 687 49
Internet: www.festo.com/catalog/...
13
Standard cylinder 1 2 3 Profile barrel Bearing and end caps Piston rod Seals
Basic version Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Polyurethane, nitrile rubber R8 S6
K10
R3
Standard cylinder 1 2 3 Profile barrel Bearing and end caps Piston rod Seals
S10
S11
TT Coated aluminium
Wrought aluminium alloy, smooth anodised Die-cast aluminium Tempered steel, High-alloy steel hard-chromium plated Polyurethane, nitrile Fluoro rubber rubber
Polyurethane
14
Internet: www.festo.com/catalog/...
1 Socket head screw with female thread for mounting attachments [mm] 32 40 50 63 80 100 125 [mm] 32 40 50 63 80 100 125 3.3 3.6 5.1 6.6 10.5 8 14 12 16 20 20 25 25 32 22 24 32 32 40 40 54 L7 AM B d11 30 35 40 45 45 55 60 MM
BG
EE
J2 TT
J3
KK
L1
L2
16 16 17 17 17 17 22 PL RT
45 54 64 75 93 110 134 TG
Gx G G Gy Gy G G VA
5.2 6 8.5 10 8 10 8 ZJ
4 4 4 4 4 4 6
26 30 37 37 46 51 65
10 13 17 17 22 22 27
16 18 24 24 30 30 36
6 6 8 8 6 6 8
Internet: www.festo.com/catalog/...
15
+ = plus stroke length ++ = plus 2x stroke length S20 Through hollow piston rod
B1
ZJ
ZM TT
10 12 16 16 20 20
16
Internet: www.festo.com/catalog/...
K8 Extended piston rod Note In combination with variant S2/S20, the piston rod is extended at one end. In combination with variant Q, the square piston rod is extended.
A1 max. 35 35 70 70 70 70 70
AF
AM
KF Basic thread
T4
WH
12 12 16 16 20 20 32
22 24 32 32 40 40 54
26 30 37 37 46 51 65
10 13 17 17 22 22 27
The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
Internet: www.festo.com/catalog/...
17
Type1) DNC-32-25-PPV DNC-32-40-PPV DNC-32-50-PPV DNC-32-80-PPV DNC-32-100-PPV DNC-32-125-PPV DNC-32-160-PPV DNC-32-200-PPV DNC-32-250-PPV DNC-32-320-PPV DNC-32-400-PPV DNC-32-500-PPV DNC-50-25-PPV DNC-50-40-PPV DNC-50-50-PPV DNC-50-80-PPV DNC-50-100-PPV DNC-50-125-PPV DNC-50-160-PPV DNC-50-200-PPV DNC-50-250-PPV DNC-50-320-PPV DNC-50-400-PPV DNC-50-500-PPV DNC-80-25-PPV DNC-80-40-PPV DNC-80-50-PPV DNC-80-80-PPV DNC-80-100-PPV DNC-80-125-PPV DNC-80-160-PPV DNC-80-200-PPV DNC-80-250-PPV DNC-80-320-PPV DNC-80-400-PPV DNC-80-500-PPV DNC-125-25-PPV DNC-125-40-PPV DNC-125-50-PPV DNC-125-80-PPV DNC-125-100-PPV DNC-125-125-PPV DNC-125-160-PPV DNC-125-200-PPV DNC-125-250-PPV DNC-125-320-PPV DNC-125-400-PPV DNC-125-500-PPV
Piston [mm] 40
Stroke [mm] 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500 25 40 50 80 100 125 160 200 250 320 400 500
Part No. 163351 163352 163353 163354 163355 163356 163357 163358 163359 163360 163361 163362 163415 163416 163417 163418 163419 163420 163421 163422 163423 163424 163425 163426 163479 163480 163481 163482 163483 163484 163485 163486 163487 163488 163489 163490
Type1) DNC-40-25-PPV DNC-40-40-PPV DNC-40-50-PPV DNC-40-80-PPV DNC-40-100-PPV DNC-40-125-PPV DNC-40-160-PPV DNC-40-200-PPV DNC-40-250-PPV DNC-40-320-PPV DNC-40-400-PPV DNC-40-500-PPV DNC-63-25-PPV DNC-63-40-PPV DNC-63-50-PPV DNC-63-80-PPV DNC-63-100-PPV DNC-63-125-PPV DNC-63-160-PPV DNC-63-200-PPV DNC-63-250-PPV DNC-63-320-PPV DNC-63-400-PPV DNC-63-500-PPV DNC-100-25-PPV DNC-100-40-PPV DNC-100-50-PPV DNC-100-80-PPV DNC-100-100-PPV DNC-100-125-PPV DNC-100-160-PPV DNC-100-200-PPV DNC-100-250-PPV DNC-100-320-PPV DNC-100-400-PPV DNC-100-500-PPV
50
63
80
100
125
1)
The mounting nut on the piston rod thread is included in the scope of delivery
18
Internet: www.festo.com/catalog/...
Type1) DNC-32-20-PPV-A DNC-32-25-PPV-A DNC-32-30-PPV-A DNC-32-40-PPV-A DNC-32-50-PPV-A DNC-32-60-PPV-A DNC-32-70-PPV-A DNC-32-80-PPV-A DNC-32-100-PPV-A DNC-32-125-PPV-A DNC-32-150-PPV-A DNC-32-160-PPV-A DNC-32-200-PPV-A DNC-32-250-PPV-A DNC-32-300-PPV-A DNC-32-320-PPV-A DNC-32-400-PPV-A DNC-32-500-PPV-A DNC-50-20-PPV-A DNC-50-25-PPV-A DNC-50-30-PPV-A DNC-50-40-PPV-A DNC-50-50-PPV-A DNC-50-60-PPV-A DNC-50-70-PPV-A DNC-50-80-PPV-A DNC-50-100-PPV-A DNC-50-125-PPV-A DNC-50-150-PPV-A DNC-50-160-PPV-A DNC-50-200-PPV-A DNC-50-250-PPV-A DNC-50-300-PPV-A DNC-50-320-PPV-A DNC-50-400-PPV-A DNC-50-500-PPV-A
Piston [mm] 40
Stroke [mm] 20 25 30 40 50 60 70 80 100 125 150 160 200 250 300 320 400 500 20 25 30 40 50 60 70 80 100 125 150 160 200 250 300 320 400 500
Part No. 1922623 163337 1922624 163338 163339 1922625 1922626 163340 163341 163342 1922627 163343 163344 163345 1922628 163346 163347 163348 1922635 163401 1922636 163402 163403 1922637 1922638 163404 163405 163406 1922639 163407 163408 163409 1922640 163410 163411 163412
Type1) DNC-40-20-PPV-A DNC-40-25-PPV-A DNC-40-30-PPV-A DNC-40-40-PPV-A DNC-40-50-PPV-A DNC-40-60-PPV-A DNC-40-70-PPV-A DNC-40-80-PPV-A DNC-40-100-PPV-A DNC-40-125-PPV-A DNC-40-150-PPV-A DNC-40-160-PPV-A DNC-40-200-PPV-A DNC-40-250-PPV-A DNC-40-300-PPV-A DNC-40-320-PPV-A DNC-40-400-PPV-A DNC-40-500-PPV-A DNC-63-20-PPV-A DNC-63-25-PPV-A DNC-63-30-PPV-A DNC-63-40-PPV-A DNC-63-50-PPV-A DNC-63-60-PPV-A DNC-63-70-PPV-A DNC-63-80-PPV-A DNC-63-100-PPV-A DNC-63-125-PPV-A DNC-63-150-PPV-A DNC-63-160-PPV-A DNC-63-200-PPV-A DNC-63-250-PPV-A DNC-63-300-PPV-A DNC-63-320-PPV-A DNC-63-400-PPV-A DNC-63-500-PPV-A
50
63
1)
The mounting nut on the piston rod thread is included in the scope of delivery
Internet: www.festo.com/catalog/...
19
Type1) DNC-80-20-PPV-A DNC-80-25-PPV-A DNC-80-30-PPV-A DNC-80-40-PPV-A DNC-80-50-PPV-A DNC-80-60-PPV-A DNC-80-70-PPV-A DNC-80-80-PPV-A DNC-80-100-PPV-A DNC-80-125-PPV-A DNC-80-150-PPV-A DNC-80-160-PPV-A DNC-80-200-PPV-A DNC-80-250-PPV-A DNC-80-300-PPV-A DNC-80-320-PPV-A DNC-80-400-PPV-A DNC-80-500-PPV-A DNC-100-25-PPV-A DNC-100-40-PPV-A DNC-100-50-PPV-A DNC-100-80-PPV-A DNC-100-100-PPV-A DNC-100-125-PPV-A DNC-100-160-PPV-A DNC-100-200-PPV-A DNC-100-250-PPV-A DNC-100-320-PPV-A DNC-100-400-PPV-A DNC-100-500-PPV-A DNC-125-25-PPV-A DNC-125-40-PPV-A DNC-125-50-PPV-A DNC-125-80-PPV-A DNC-125-100-PPV-A DNC-125-125-PPV-A DNC-125-160-PPV-A DNC-125-200-PPV-A DNC-125-250-PPV-A DNC-125-320-PPV-A DNC-125-400-PPV-A DNC-125-500-PPV-A
100
125
1)
The mounting nut on the piston rod thread is included in the scope of delivery
20
Internet: www.festo.com/catalog/...
Without position sensing Part No. Type1) 163318 163350 163382 163414 163446 163478 163510 DNC-32--PPV DNC-40--PPV DNC-50--PPV DNC-63--PPV DNC-80--PPV DNC-100--PPV DNC-125--PPV
The mounting nut on the piston rod thread is included in the scope of delivery
Ordering data Variable stroke Piston Stroke [mm] [mm] 32 40 50 63 80 100 125
1)
With position sensing Part No. Type1) 163304 163336 163368 163400 163432 163464 163496 DNC-32--PPV-A DNC-40--PPV-A DNC-50--PPV-A DNC-63--PPV-A DNC-80--PPV-A DNC-100--PPV-A DNC-125--PPV-A
The mounting nut on the piston rod thread is included in the scope of delivery
Internet: www.festo.com/catalog/...
21
Piston
Cushioning
Special thread
163 302 163 334 163 366 163 398 163 430 163 462 163 494 Order example 163 430 Ordering table Size 0 M Module No. Function Piston Stroke Cushioning
DNC
32 40 50 63 80 100 125
10 2,000
K3
K5
DNC
80
550
PPV
S2
K3
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
Condition Code s
Enter code
Standard cylinder, double-acting, based on ISO 15552 [mm] 32 40 50 63 80 [mm] 10 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Square piston rod Through piston rod Through, hollow piston rod Piston rod with extended male thread [mm] 1 35 1 70 Piston rod with female thread (M6) (M8) (M10) (M10) Piston rod with special thread M10 M12 M16 M16x2
4
aE 2 3 4 5
DNC
0 O Position sensing Protection against rotation Type of piston rod Extended male thread Female thread Special thread
(M12) M20
(M12) M20
(M16) M27
6 7
aE 2
PPV For piston 125 not with S11 Q Max. stroke: 10 1,500 mm. In combination with S2: square piston rod at bearing cap end only. Not with S20, K7, K10, S10, S11, R8
S20 Max. stroke: 850 mm. In combination with K8: piston rod extended at one end. Not with K2, K3, K5, K10, S6, S10, S11, R8
5 6 7
K2 K3 K5
Not with K3, K10 With K5: on request. Not with K7 Not with K10
S2
In combination with K2: thread extended at both ends. In combination with K3: female thread at both ends. In combination with K5: special thread at both ends. In combination with K8: piston rod extended at bearing cap end only. Not with K7, S10, S11
22
Internet: www.festo.com/catalog/...
Corrosion protection
K7
K8
K10
S6
S11
R3
R8
100K8
32
40
50
63
80
100
125
Condition Code s 8 -K7 -K8 -K10 -S6 -TT -S10 -S11 -R3 -R8
Enter code
Piston rod with external hexagon Extended piston rod [mm] 1 500 Improved running performance Smooth anodised aluminium coated piston rod Temperature resistance Heat-resistant seals for temperatures up to 120 C Low temperature [C] 40 +80 Slow speed (constant motion) Slow speed (constant motion at low piston speeds) Running characteristics Low friction Corrosion protection High corrosion protection Wiper seal Dust protection
Not with Q, S2, K10 Max. stroke: 1,000 mm. Not with S6, R3, R8 aC S11 aD CT, R3 Not with S10, S11, R8 Not with P, Q, K7, K10, S6, S10, S11, R8 aB S10
9 aJ aA aB aC aD
8 K7 9 K10 aJ S6 aA TT
Max. stroke: 500 mm; additional strokes on request. Not with S11, R3, R8 Max. stroke: 500 mm; additional strokes on request. Not with R3, R8 Not with R8
Internet: www.festo.com/catalog/...
23
24
Internet: www.festo.com/catalog/...
www.festo.com/en/ Spare_parts_service Wearing parts kits 32 DNC--A--KP With position sensing Note
Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without
additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems.
General technical data Piston Pneumatic connection Piston rod thread K3 K5 [mm] Cylinder KP
40 G Gx M12x1.25 M8 M12
Max. axial backlash with clamped piston rod without load Constructional design
Piston Piston rod Profile barrel Clamping unit Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 Via proximity sensor Via female thread Via accessories Any At both ends
22
32
32
42
Operating and environmental conditions Operating medium Note on operating/pilot medium Operating pressure [bar] Min. release pressure [bar] Ambient temperature1) [C] Corrosion resistance class CRC2) Certification
1) 2)
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 1.5 10 3 10 +80 2 Germanischer Lloyd
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Internet: www.festo.com/catalog/...
25
32
40 0.2
63 0.5
80 0.9
125 5
vperm. =
Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
Maximum permissible load: Forces [N] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Static holding force Note The specified holding force refers to a static load. If this value is exceeded, slippage may occur. Dynamic forces occurring during operation must not S2 S2
m load =
2 x E perm. m dead v2
This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
exceed the static holding force. The clamping unit is not backlash-free in the clamped condition if varying loads are applied to the piston rod.
Activation: The clamping unit may only be released if the forces at the piston have reached equilibrium. Otherwise, there is a risk of accidents due to
sudden movement of the piston rod. Blocking off the air supply at both ends (e.g. with a 5/3-way valve) does not provide any safety.
26
Internet: www.festo.com/catalog/...
Fq
Standard cylinder 1 2 3 4 5 6 7 Profile barrel Bearing and end caps Piston rod Housing, clamping unit Clamping jaws Spring Piston Seals Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Wrought aluminium alloy, anodised Brass Spring steel Polyacetal Polyurethane, nitrile rubber
Internet: www.festo.com/catalog/...
27
1 Socket head screw with female thread for mounting attachments [mm] 32 40 50 63 80 100 125 [mm] 32 40 50 63 80 100 125 14 16 20 24 31.5 31 42 3.3 3.6 5.1 6.6 10.5 8 14 12 16 20 20 25 25 32 22 24 32 32 40 40 54 L5 AM B d11 30 35 40 45 45 55 60 L7 BG
D1 f9 20 24 30 38 48 48 65 PL
D2
EE
H1
J2
J3
KK
L2
L3
16 16 17 17 17 17 22 MM
M5 Gx Gx Gx Gx Gx Gx RT
45 54 64 75 93 110 134 TG
Gx G G Gy Gy G G VA
5.2 6 8.5 10 8 10 8 ZJ
45 53 67 76 95 98 125 3
4 4 4 4 4 4 6
26 30 37 37 46 51 65
10 13 17 17 22 22 27
16 18 24 24 30 30 36
6 6 8 8 6 6 8
28
Internet: www.festo.com/catalog/...
+ = plus stroke length ++ = plus 2x stroke length Note The thread types at both piston rod ends are identical. K2 Extended male piston rod thread In combination with variant Q, the left-hand piston rod is round, the right-hand piston rod square. The clamping unit is mounted on K3 Female piston rod thread the left-hand, round piston rod.
K8 Extended piston rod Note In combination with variant S2, the piston rod is extended at one end. The clamping unit is mounted on the side of the piston rod that is not extended. If variant Q is also required, the extension will only be added to the square piston rod.
A1 max. 35 35 70 70 70 70 70
AF
AM
B1
KF Basic thread
T4
WH
ZJ
ZM
12 12 16 16 20 20 32
22 24 32 32 40 40 54
10 12 16 16 20 20
26 30 37 37 46 51 65
10 13 17 17 22 22 27
The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
Internet: www.festo.com/catalog/...
29
163 302 163 334 163 366 163 398 163 430 163 462 163 494 Order example 163 430 Ordering table Size 0 M Module No. Function Piston Stroke Cushioning
DNC
32 40 50 63 80 100 125
10 2,000
P PPV
S2
DNC
80
550
PPV
S2
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
Condition Code s
Enter code
Standard cylinder, double-acting, standard hole pattern, with clamping unit [mm] 32 40 50 63 80 100 125 [mm] 10 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Square piston rod Through piston rod
2 S2
DNC
In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends In combination with K8: piston rod extended at bearing cap end only In combination with KP: clamping unit at end cap Not with K7
In combination with S2: square piston rod at bearing cap end only In combination with KP: only supplied with S2 Not with K7
30
Internet: www.festo.com/catalog/...
K2
K3
K5
K7
K8
KP
V1 V2 V3 V4 V5 V6
K3
100K8
KP
32
40
50
63
80
100
125
Condition Code s 3 -K2 -K3 -K5 -K7 -K8 -KP -V1 -V2 -V3 -V4 -V5 -V6
Enter code
Piston rod with extended male thread [mm] 1 35 1 70 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) (M12) (M12) Special thread Piston rod with special thread M10 M12 M16 M16 M20 M20 Special spanner flats Piston rod with external hexagon Extended piston rod Extended piston rod [mm] 1 500 0 M Clamping unit Attached 0 O Cylinder/valve combination Single solenoid valve, fitted on right, piston rod retracted when unactuated Single solenoid valve, fitted on right, piston rod advanced when unactuated Double solenoid valve, fitted on right Single solenoid valve, fitted on left, piston rod retracted when unactuated Single solenoid valve, fitted on left, piston rod advanced when unactuated Double solenoid valve, fitted on left 0 O
3 4 K2 K3 Not with K3 With K5: on request Not with K7 5 6 KP V
(M16) M27
5 6 6 6 6 6 6
-KP
Without S2: position of the clamping unit at the bearing cap Min. stroke: 100 mm
Internet: www.festo.com/catalog/...
31
32
Internet: www.festo.com/catalog/...
-N-T-
Note Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems.
General technical data Piston Pneumatic connection Piston rod thread Max. axial backlash with end position locked Constructional design Cylinder EL [mm]
32 Gx M3 M10x1.25 1.3
40 G M12x1.25
50 G M5 M16x1.5
63 Gy M16x1.5
80 Gy M20x1.5 2.1
100 G M20x1.5
End-position locking
Cushioning Cushioning length PPV [mm] Position sensing Type of mounting Mounting position
EL
Piston Piston rod Profile barrel At both ends At front At rear Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 8.2 8.3 7.3 Via proximity sensor Via female thread Via accessories Any
22 10.8
32 9.8
32 11.8
Note End-position locking should only be operated in conjunction with double-acting cylinders with exhaust air flow control in order to ensure that the lock is always completely released prior to starting the drive movement. No screws with a head or similar may be used in place of end-position locking, as there is a risk that the function will be impaired if they are screwed in too deeply. The exhaust hole must not be closed. Locking can be performed from any stroke position once the drive is brought mechanically into its end position. End-position locking has been designed to prevent the load dropping in case of pressure failure. An excessive end-position cushioning setting (more than 50% closed) can result in the locking bolt not engaging reliably, resulting in premature wear.
Internet: www.festo.com/catalog/...
33
40
50
63
80
100
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 2.5 12 1.5 12 20 +80 2 Germanischer Lloyd
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
32
40 0.2
63 0.5 Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
80 0.9 Note
100 1.2
vperm. =
Maximum permissible load: Forces [N] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Static holding force Sizing example Note When sizing pneumatic cylinders it is recommended as a basic principle that only 50% of the indicated theoretical forces (see above) be used.
m load =
2 x E perm. m dead v2
This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
40 754 633
63 1,870 1,682
Given: Installation position = Vertical Workpiece load = 44 kg F = m x g = 44 kg x 9.81 m/s2 = 431.6 N To be calculated: Suitable piston
Example with 32 mm piston : Theoretical force at 6 bar, advancing = 483 N 50% of the theoretical force = 241.5 N Static holding force with 32 mm piston = 500 N The static holding force of end-position locking is within the permissible range (max. 500 N) with a workpiece load of 44 kg (431.6 N), however the cylinder would be at 89% capacity. Result: A cylinder with a piston of 40 mm is therefore recommended for this application.
34
Internet: www.festo.com/catalog/...
Fq
Weight [g] Piston Basic version Product weight with 0 mm stroke Additional weight per 10 mm stroke S2 Through piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Materials Sectional view 2 1 3 2
32 40 50/63 80/100
32 537 30
40 820 45
50 1,320 64
63 1,769 73
80 2,970 106
596 39
915 61
1,450 89
1,977 98
3,294 144
5,477 153
Standard cylinder 1 2 3 Profile barrel Bearing and end caps Piston rod Seals Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Polyurethane, nitrile rubber
Internet: www.festo.com/catalog/...
35
1 Socket head screw with female thread for mounting attachments Dimensions Variants S2 Through piston rod
www.festo.com/us/cad
+ = plus stroke length ++ = plus 2x stroke length [mm] 32 40 50 63 80 100 [mm] 32 40 50 63 80 100 94 105 106 121 128 138 13.8 16.6 17.1 16.6 19.9 22.8 12 16.6 17.1 16.6 19.9 22.8 3.3 3.6 5.1 6.6 10.5 8 12 16 20 20 25 25 15.6 14 14 17 16.4 18.8 M6 M6 M8 M8 M10 M10 32.5 38 46.5 56.5 72 89 4 4 4 4 4 4 10 10.5 11.5 15 15.7 19.2 22 24 32 32 40 40 L2 AM B d11 30 35 40 45 45 55 L3 BG D1 f8 13 13 20 20 20 20 L7 D2 E EE G H1 H2 J1 J2 J3 KK L1
16 16 17 17 17 17 L4
M3 M3 M5 M5 M5 M5 MM
45 54 64 75 93 110 PL
Gx G G Gy Gy G RT
70 74 93 93 116 116 VD
5.2 6 8.5 10 8 10 ZJ
10 13 17 17 22 22
16 18 24 24 30 30
6 6 8 8 6 6
36
Internet: www.festo.com/catalog/...
K8 Extended piston rod Note In combination with variant S2, the piston rod is extended at one end.
[mm] 32 40 50 63 80 100
1)
A1 max. 35 35 70 70 70 70
AF
AM
KF Basic thread
T4
WH
12 12 16 16 20 20
22 24 32 32 40 40
26 30 37 37 46 51
10 13 17 17 22 22
The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
Internet: www.festo.com/catalog/...
37
0 O Options Piston 32 40 50 63 80 100 Stroke 10 2,000 Cushioning P PPV Position sensing A Type of piston rod S2
Function DNC
DNC
80
550
PPV
S2
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
Condition Code s
Enter code
Standard cylinder, double-acting, standard hole pattern, with end-position locking [mm] 32 40 50 63 80 100 [mm] 10 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Through piston rod 1
DNC
In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends
38
Internet: www.festo.com/catalog/...
Ordering table Size Extended male thread 0 O Female thread Special thread Extended piston rod 0 M End-position locking
K3
100K8
32
40
50
63
80
100
Enter code
Piston rod with extended male thread [mm] 1 35 1 70 Piston rod with female thread (M6) (M8) (M10) Piston rod with special thread M10 M12 M16 Extended piston rod [mm] 1 500 At both ends At front At rear
(M10) M16
(M12) M20
(M12) M20
2 K2 3 K3
Not with K3 With K5: on request In combination with K8 and S2: on request only
Internet: www.festo.com/catalog/...
39
Single solenoid valve unactuated, piston rod advanced Note As viewed from the front of the cylinder (piston rod end) with valve fitted on left or right. DNC--V2 fitted on right In this example, the valve is fitted on the right.
40
Internet: www.festo.com/catalog/...
32
40
50
Cushioning Cushioning length PPV Position sensing Type of mounting Mounting position Valve Valve used [mm]
Gx G G M10x1.25 M12x1.25 M16x1.5 M6 M8 M10 M10 M12 M16 Piston Piston rod Profile barrel Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 20 20 22 Via proximity sensor Via female thread Via accessories Any
22
32
32
CPE14-M1BH-5L-x CPE14-M1BH-5J-x Gx Piston spool valve Via mounting kit 24 +10/15% 1 100% IP65
CPE18-M1H-5L- CPE18-M1H-5J- G
48
Pneumatic connection Constructional design Type of mounting Operating voltage [V DC] Power consumption [W] Duty cycle Protection class with plug socket
Note: This product conforms to ISO 1179-1 and ISO 228-1
1.5
Operating and environmental conditions Piston 32 Operating medium Note on operating/pilot medium Operating pressure [bar] Ambient temperature1) [C] Corrosion resistance class CRC2) Certification
1) 2)
40
50
63
80
100
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 38 2.5 10 0 +50 2 Germanischer Lloyd
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Internet: www.festo.com/catalog/...
41
S2/S20 S2/S20
The permissible impact energy is reduced by approx. 10% for variants K10 and S20
vperm. =
Permissible impact velocity Max. impact energy Moving load (drive) Moving effective load
Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed.
m load =
2 x E perm. m dead v2
Fq
32 40 50/63 80/100
42
Internet: www.festo.com/catalog/...
3 Standard cylinder 1 2 3 4 Profile barrel Bearing and end caps Piston rod Seals, cylinder Housing, valve Seals, valve Basic version R8 S10
4 S11 K10
Wrought aluminium alloy, smooth anodised Die-cast aluminium High-alloy steel Tempered steel Polyurethane, nitrile rubber Die-cast aluminium, polyamide, steel Nitrile rubber
Internet: www.festo.com/catalog/...
43
44
Internet: www.festo.com/catalog/...
Internet: www.festo.com/catalog/...
45
163 302 163 334 163 366 163 398 163 430 163 462 Order example 163 430 Ordering table Size 0 M Module No. Function Piston Stroke Cushioning
DNC
32 40 50 63 80 100
100 2,000
P PPV
S2 S20
DNC
80
550
PPV
S2
32 163 302
40 163 334
50 163 366
63 163 398
80 163 430
Condition Code s
Enter code
Standard cylinder, double-acting, standard hole pattern, cylinder/valve combination [mm] 32 40 50 63 80 100 [mm] 100 2,000 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Square piston rod Through piston rod Through, hollow piston rod
2 S2
DNC
Max. stroke: 100 1,500 mm In combination with S2: square piston rod at bearing cap end only In combination with KP: only supplied with S2 Not with S20, K7, K10, S10, S11
In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends In combination with K8: piston rod extended at bearing cap end only In combination with KP: clamping unit at end cap Not with S20, K7, S10, S11
S20 Max. stroke: 850 mm In combination with K8: piston rod extended end only Not with K2, K3, K5, K10, KP, S10, S11
46
Internet: www.festo.com/catalog/...
K2
K3
K5
K7
K8
KP
S11
V1 V2 V3 V4 V5 V6
100K8
V2
32
40
50
63
80
100
Condition Code s 4 -K2 -K3 -K5 -K7 -K8 -K10 -KP -S10 -S11 -V1 -V2 -V3 -V4 -V5 -V6
Enter code
Piston rod with extended male thread [mm] 1 35 1 70 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) Special thread Piston rod with special thread M10 M12 M16 M16 Special spanner flats Piston rod with external hexagon Extended piston rod Extended piston rod [mm] 1 500 Improved running performance Smooth anodised aluminium coated piston rod Clamping unit Attached Slow speed (constant motion) Slow speed (constant motion at low piston speeds) Running characteristics Low friction
(M12) M20
(M12) M20
5 6 7
8 9 aJ aA
0 M Cylinder/valve combination
Single solenoid valve, fitted on right, piston rod retracted when unactuated Single solenoid valve, fitted on right, piston rod advanced when unactuated Double solenoid valve, fitted on right Single solenoid valve, fitted on left, piston rod retracted when unactuated Single solenoid valve, fitted on left, piston rod advanced when unactuated Double solenoid valve, fitted on left
8 9 aJ aA K10 Max. stroke: 1,000 mm Not with KP KP Without S2: position of the clamping unit at the bearing cap Not with S10, S11 S10 Max. stroke: 500 mm; additional strokes on request Not with S11 S11 Max. stroke: 500 mm; additional strokes on request
4 5 6 7
K2 K3 K5 K7
Not with K3, K10 With K5: on request Not with K7 Not with K10 Not with Q, S2, K10
Internet: www.festo.com/catalog/...
47
Technical data Internet: plug socket with cable 185 519 KMYZ-4-24-0,5 185 520 151 688 151 689 193 457 KMYZ-4-24-2,5 KMEB-1-24-2,5-LED KMEB-1-24-5-LED KMEB-1-24-10-LED
Mounting kit ZVB CPE14 CPE18 CPE24 185 705 187 388 ZVB-8-14/18 ZVB-8-24
1)
48
Internet: www.festo.com/catalog/...
Max. overall stroke length [mm] 1,000 1,000 1,000 1,000 1,000 1,000 1,000
Part No.
Type
174 418 174 419 174 420 174 421 174 422 174 423 174 424
Connecting two cylinders with identical piston diameter as a 3 or 4-position cylinder A 3 or 4-position cylinder consists of two separate cylinders whose piston rods advance in opposing directions. To achieve 3 positions Two cylinders with identical stroke length must be connected together. This means that depending on actuation and stroke division, this type of cylinder can assume up to four positions. In each case the cylinder is driven precisely against a stop. Note that when one end of the piston rod is To achieve 4 positions Two cylinders with different stroke lengths must be connected together. fixed, the cylinder barrel executes the movement. The cylinders connections must be flexible.
Internet: www.festo.com/catalog/...
49
+ Dimensions and ordering data For AB AH [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 125
1)
AO
AT
AU
TR
US
XS
7 10 10 10 12 14.5 16.5
32 36 45 50 63 71 90
4 4 5 5 6 6 8
24 28 32 32 41 41 45
32 36 45 50 63 75 90
45 54 64 75 93 110 131
45 53 62 63 81 86 102
Basic version CRC1) Weight [g] 2 2 2 2 2 2 2 144 193 353 436 829 1,009 1,902
Part No. 174 369 174 370 174 371 174 372 174 373 174 374 174 375
High corrosion protection CRC1) Weight Part No. [g] 4 4 4 4 4 4 4 139 188 341 424 809 990 1,920 176 937 176 938 176 939 176 940 176 941 176 942 176 943
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
50
Internet: www.festo.com/catalog/...
Dimensions and ordering data For E [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 125
1)
FB H13 7 9 9 9 12 14 16
MF
TF
UF
W Basic version
45 54 65 75 93 110 132 Basic version CRC1) Weight [g] 1 1 1 1 1 1 1 221 291 536 679 1,495 2,041 3,775
10 10 12 12 16 16 20
32 36 45 50 63 75 90
16 20 25 25 30 35 45
Part No. 174 376 174 377 174 378 174 379 174 380 174 381 174 382
High corrosion protection CRC1) Weight Part No. [g] 4 4 4 4 4 4 4 240 300 550 710 1,680 2,450 3,660 161 846 161 847 161 848 161 849 161 850 161 851 185 363
CRC1: Corrosion resistance class to Festo standard 940070 Components with light corrosion exposure. Protection for transport and storage. Components without significant decorative function or surface, e.g. installed out of sight internally or behind covers. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
Internet: www.festo.com/catalog/...
51
TD e9 12 16 16 20 20 25 25
TK
TL
TM
US
XH
71 87 99 116 136 164 192 Basic version CRC1) Weight [g] 2 2 2 2 2 2 2 130 240 390 600 1,150 2,030 3,490
16 20 24 24 28 38 50
12 16 16 20 20 25 25
45 54 64 75 93 110 131
18 20 25 25 32 32 40
Part No. 174 411 174 412 174 413 174 414 174 415 174 416 174 417
High corrosion protection CRC1) Weight Part No. [g] 4 4 4 4 4 4 4 150 260 430 640 1,300 2,400 3,600 161 852 161 853 161 854 161 855 161 856 161 857 185 362
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
52
Internet: www.festo.com/catalog/...
+ = plus stroke length + = plus half stroke length Dimensions and ordering data For B1 [mm] 32 40 50 63 80 100 125 For [mm] 32 40 50 63 80 100 125
1)
C2
C3
TD e9 12 16 16 20 20 25 25 XV
TL
TM
UW Basic version
30 32 34 41 44 48 50 XJ
65 75 95 105 130 145 175 Weight [g] 2 2 2 2 2 2 2 224 396 616 931 1,494 2,095 3,013
KP 79.9 89.4 96.4 101.9 116.1 126.2 155.3 124.9 142.4 163.4 177.9 211.1 224.2 280.3 73 82.5 90 97.5 110 120 145
163 525 163 526 163 527 163 528 163 529 163 530 163 531
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Internet: www.festo.com/catalog/...
53
Dimensions and ordering data For CR DA FK [mm] D11 H13 0.1 32 40, 50 63, 80 100, 125
1)
FN
FS
H1
HB H13 6.6 9 11 14
KE
NH
TH 0.2
UL
CRC1)
Weight [g]
Part No.
Type
12 16 20 25
11 15 18 20
15 18 20 25
30 36 40 50
10.5 12 13 16
15 18 20 24.5
6.8 9 11 13
18 21 23 28.5
32 36 42 50
46 55 65 75
2 2 2 2
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Trunnion support CRLNZG Material: High-alloy steel Free of copper and PTFE RoHS-compliant
Dimensions and ordering data For CR FK [mm] D11 0.1 32 40, 50 63, 80 100, 125
1)
FN
FS
H1
HB H13 6.6 9 11 14
NH
TH 0.2
UL
CRC1)
Weight [g]
Part No.
Type
12 16 20 25
15 18 20 25
30 36 40 50
10.5 12 13 16
15 18 20 24.5
18 21 23 28.5
32 36 42 50
46 55 65 75
4 4 4 4
Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
54
Internet: www.festo.com/catalog/...
+ = plus stroke length 1 The pivot pin is protected against rotation with a dowel pin. Dimensions and ordering data For CG CP [mm] 32 40 50 63 80 100 125
1)
H14 14 16 21 21 25 25 37
h14 34 40 45 51 65 75 97
EK H9 10 12 16 16 20 20 30
FL 0.2 22 25 27 32 36 41 50
SR
XC KP
CRC1)
Weight [g]
Part No.
Type
13 16 16 21 22 27 30
10 12 12 16 16 20 25
2 2 2 2 2 2 2
174 383 174 384 174 385 174 386 174 387 174 388 174 389
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Internet: www.festo.com/catalog/...
55
H14 26 28 32 40 50 60 70 Basic version CRC1) Weight [g] 2 2 2 2 2 2 2 103 155 232 375 636 1035 1860
EK e8 10 12 12 16 16 20 25
FL 0.2 22 25 27 32 36 41 50
MR
UB h14
XC KP 142 160 170 190 210 230 275 187 213 237 266 305 328 400
13 16 16 21 22 27 30
8.5 12 12 16 16 20 25
45 52 60 70 90 110 130
Part No. 174 390 174 391 174 392 174 393 174 394 174 395 174 396
Variant R3 High corrosion protection CRC1) Weight Part No. Type [g] 3 3 3 3 3 3 3 100 151 228 371 632 986 1776 176 944 176 945 176 946 176 947 176 948 176 949 176 950 SNCB-32-R3 SNCB-40-R3 SNCB-50-R3 SNCB-63-R3 SNCB-80-R3 SNCB-100-R3 SNCB-125-R3
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
56
Internet: www.festo.com/catalog/...
EX
FL 0.2
LT
MS
XC KP
CRC1)
Weight [g]
Part No.
Type
10 12 16 16 20 20 30
10.5 12 15 15 18 18 25
14 16 21 21 25 25 37
22 25 27 32 36 41 50
13 16 16 21 22 27 30
15 17 20 22 27 29 39
2 2 2 2 2 2 2
174 397 174 398 174 399 174 400 174 401 174 402 174 403
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Swivel flange SNCL Material: Die-cast aluminium Free of copper and PTFE RoHS-compliant
FL 0.2 22 25 27 32 36 41 50
MR
XC KP
CRC1)
Weight [g]
Part No.
Type
10 12 12 16 16 20 25
26 28 32 40 50 60 70
13 16 16 21 22 27 30
10 12 12 16 16 20 25
2 2 2 2 2 2 2
174 404 174 405 174 406 174 407 174 408 174 409 174 410
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Internet: www.festo.com/catalog/...
57
Type
Clevis foot for welding LSNSG 32 40 50 63 80 100 125 Right-angle clevis foot LQG 32 40 50 63 80 100 125
LQG-32 LQG-40 LQG-50 LQG-63 LQG-80 LQG-100 LQG-125 Technical data Type CRLNG-32 CRLNG-40 CRLNG-50 CRLNG-63 CRLNG-80 CRLNG-100 CRLNG-125 Internet: crlng
Ordering data Mounting attachments, corrosion-resistant Designation For Clevis foot CRLNG 32 40 50 63 80 100 125
Part No. 161 840 161 841 161 842 161 843 161 844 161 845 176 951
58
Internet: www.festo.com/catalog/...
Type
Self-aligning rod coupler FK 32 40 50 63 80 100 125 Coupling piece KSZ 32 40 50 63 80 100 125
Ordering data Piston rod attachments, corrosion-resistant Designation For Part No. Type Rod eye CRSGS 32 40 50 63 80 100 125 195 582 195 583 195 584 195 585 195 586 CRSGS-M10x1,25 CRSGS-M12x1,25 CRSGS-M16x1,5 CRSGS-M20x1,5 CRSGS-M27x2
Internet: www.festo.com/catalog/...
59
-V- New
Bellows DADB Standard cylinders DNC, ISO 15552
Accessories Bellows kit DADB
General technical data Type DADB-V6Max. cylinder stroke range1) Type of mounting Mounting position Resistance to media Ambient temperature2) Protection class Corrosion resistance class CRC3)
1) 2)
32 [mm]
40
50 10 500
63 10 500
80 10 500
100 10 500
[C]
10 500 10 500 Via threaded pin Any Dust, chips, oil, grease, fuel ( 10 +80 IP54 3
In combination with the bellows kit DADB Note operating range of proximity sensors and cylinder Corrosion resistance class 3 as per Festo standard 940 070 Components with heavy corrosion exposure. Externally visible components in direct contact with normal industrial atmosphere or media such as solvents and cleaning agents, where the surface requirement is predominantly functional.
Materials Sectional view 5 1 2 3 4 Bellows 1 2 3 4 5 Connection Intermediate piece Bellows End piece Connector O-ring Note on materials Polyamide Polyamide Nitrile rubber Polyamide Polyamide Nitrile rubber Free of copper and PTFE RoHS-compliant
Weight [g] Type DADB-V6Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500
100 124 152 165 218 255 293 284 321 359 349
60
Internet: www.festo.com/catalog/...
-V- New
Bellows DADB Standard cylinders DNC, ISO 15552
Accessories Travel velocity v as a function of tubing length l The bellows kit is a leak-free system. To prevent unwanted media being drawn in, the supply and exhaust air must be ducted via a venting hole in the connection part 1. The pressure generated in the bellows kit by the positioning motion is primarily defined by travel velocity and tubing length. The recommended tubing length based on the travel velocity of the drive can be read from the graph.
Advancing
Returning
32/50/63 40 Note The push-in fittings opposite must be used for the venting hole. Silencers can also be used as an alternative. This reduces the travel velocity slightly.
80/100
32 40
50/63 80/100
Tubing size and push-in fitting for venting hole Tubing O.D. [mm] [mm] 32, 40 8
Push-in fitting Part No. Type 186 109 533 929 533 880 186 350 533 848 533 884 QS-Gx-8-I QS-F-Gx-8-I QS-F-Gx-8H QS-G-12 QS-F-G-12 QS-F-G-12H
12
Internet: www.festo.com/catalog/...
61
-V- New
Bellows DADB Standard cylinders DNC, ISO 15552
Accessories Dimensions Download CAD Data www.festo.com/us/cad
+ Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 Stroke [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500
1)
D1 max.
D2
32 EE
L1
L2
D1 max.
D2
40 EE
L1
L2
38
14
Gx
12.9
5.4
46
14
Gx
16.3
5.4
D1 max.
D2
50 EE
L1
L2
D1 max.
D2
63 EE
L1
L2
57
17
22.35
57
17
22.4
D1 max.
D2
80 EE
L1
L2
D1 max.
D2
100 EE
L1
L2
93
17
28
93
17
28
The dimension corresponds to the K8 value (extended piston rod) of the drive
62
Internet: www.festo.com/catalog/...
-V- New
Bellows DADB Standard cylinders DNC, ISO 15552
Accessories Ordering data Bellows kit An extended piston rod (order code K8) is absolutely necessary when using a bellows kit. Ordering data Modular products. The necessary dimension for K8 as a function of piston diameter and cylinder stroke as well as the associated bellows kit is indicated in the following table: Order example: Selected standard cylinder: DNC-32-320-PPV-A- Dimension for the corresponding K8 value (see table): 112 mm Complete type designation for the standard cylinder: DNC-32-320-PPV-A--112K8 Associated bellows kit: DADB-V6-32-S301-350 Cylinder data Stroke [mm] 40 [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 Bellows kit Dimension Part No. Type for K8 [mm] 28 43 56 72 86 100 101 115 130 131 28 46 56 73 86 97 105 116 126 134 25 37 49 62 74 86 87 98 110 111 553 291 553 293 553 295 553 297 553 399 553 301 553 303 553 305 553 307 553 309 553 331 553 333 553 335 553 337 553 339 553 341 553 343 553 345 553 347 553 349 553 371 553 373 553 375 553 377 553 379 553 381 553 383 553 385 553 387 553 389 DADB-V6-40-S10-50 DADB-V6-40-S51-125 DADB-V6-40-S126-175 DADB-V6-40-S176-250 DADB-V6-40-S251-300 DADB-V6-40-S301-350 DADB-V6-40-S351-375 DADB-V6-40-S376-425 DADB-V6-40-S426-475 DADB-V6-40-S476-500 DADB-V6-63-S10-50 DADB-V6-63-S51-125 DADB-V6-63-S126-175 DADB-V6-63-S176-250 DADB-V6-63-S251-300 DADB-V6-63-S301-350 DADB-V6-63-S351-375 DADB-V6-63-S376-425 DADB-V6-63-S426-475 DADB-V6-63-S476-500 DADB-V6-100-S10-50 DADB-V6-100-S51-125 DADB-V6-100-S126-175 DADB-V6-100-S176-250 DADB-V6-100-S251-300 DADB-V6-100-S301-350 DADB-V6-100-S351-375 DADB-V6-100-S376-425 DADB-V6-100-S426-475 DADB-V6-100-S476-500
Cylinder data Stroke [mm] 32 [mm] 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500 10 50 51 125 126 175 176 250 251 300 301 350 351 375 376 425 426 475 476 500
Bellows kit Dimension Part No. Type for K8 [mm] 29 47 61 80 96 112 114 130 145 147 28 46 56 73 86 97 105 116 126 134 25 37 49 62 74 86 87 98 110 111 553 271 553 273 553 275 553 277 553 279 553 281 553 283 553 285 553 287 553 289 553 311 553 313 553 315 553 317 553 319 553 321 553 323 553 325 553 327 553 329 553 351 553 353 553 355 553 357 553 359 553 361 553 363 553 365 553 367 553 369 DADB-V6-32-S10-50 DADB-V6-32-S51-125 DADB-V6-32-S126-175 DADB-V6-32-S176-250 DADB-V6-32-S251-300 DADB-V6-32-S301-350 DADB-V6-32-S351-375 DADB-V6-32-S376-425 DADB-V6-32-S426-475 DADB-V6-32-S476-500 DADB-V6-50-S10-50 DADB-V6-50-S51-125 DADB-V6-50-S126-175 DADB-V6-50-S176-250 DADB-V6-50-S251-300 DADB-V6-50-S301-350 DADB-V6-50-S351-375 DADB-V6-50-S376-425 DADB-V6-50-S426-475 DADB-V6-50-S476-500 DADB-V6-80-S10-50 DADB-V6-80-S51-125 DADB-V6-80-S126-175 DADB-V6-80-S176-250 DADB-V6-80-S251-300 DADB-V6-80-S301-350 DADB-V6-80-S351-375 DADB-V6-80-S376-425 DADB-V6-80-S426-475 DADB-V6-80-S476-500
50
63
80
100
Internet: www.festo.com/catalog/...
63
Stroke [mm] For 40 mm 10 50 10 100 10 160 10 200 10 250 10 320 10 400 10 500 For 63 mm 10 50 10 100 10 160 10 200 10 250 10 320 10 400 10 500 For 100 mm 10 50 10 100 10 160 10 200 10 250 10 320 10 400 10 500
Part No.
FENG-100-50-KF FENG-100-100-KF FENG-100-160-KF FENG-100-200-KF FENG-100-250-KF FENG-100-320-KF FENG-100-400-KF FENG-100-500-KF Internet: feng
Ordering data Guide units for variable strokes For Stroke [mm] [mm] 32 40 50 63 80 100 10 500 10 500 10 500 10 500 10 500 10 500
With recirculating ball bearing guide Part No. Type 34 487 34 488 34 489 34 490 34 491 34 492 FENG-32--KF FENG-40--KF FENG-50--KF FENG-63--KF FENG-80--KF FENG-100--KF
Technical data With plain-bearing guide Part No. Type 34 481 34 482 34 483 34 484 34 485 34 486 FENG-32- FENG-40- FENG-50- FENG-63- FENG-80- FENG-100- Technical data Type SMB-8-FENG-32/40 SMB-8-FENG-50/63 SMB-8-FENG-80/100
Ordering data Mounting kits for proximity sensors SMT-8 For [mm] 32 40 50 63 80 100
Internet: smb
64
Internet: www.festo.com/catalog/...
Electrical connection
Part No.
NPN Insertable in the slot lengthwise, flush with the cylinder profile N/C contact Insertable in the slot from above, flush with the cylinder profile PNP PNP
Cable, 3-wire
7.5
543 873
SMT-8M-PO-24V-K7,5-OE
Ordering data Proximity sensors for T-slot, magnetic reed Type of mounting Switching output N/O contact Insertable in the slot from above, flush with the cylinder profile Contacting
Electrical connection
Part No.
Internet: sme
Cable, 3-wire Cable, 2-wire Plug M8x1, 3-pin Cable, 3-wire Plug M8x1, 3-pin
Insertable in the slot lengthwise, flush with the cylinder profile N/C contact Insertable in the slot lengthwise, flush with the cylinder profile Ordering data Connecting cables Electrical connection, left Straight socket, M8x1, 3-pin Straight socket, M12x1, 5-pin Angled socket, M8x1, 3-pin Angled socket, M12x1, 5-pin
Contacting
543 862 543 863 543 872 543 861 150 855 150 857
Contacting
Cable, 3-wire
7.5
160 251
SME-8-O-K-LED-24
Electrical connection, right Cable, open end, 3-wire Cable, open end, 3-wire Cable, open end, 3-wire Cable, open end, 3-wire
Part No. 541 333 541 334 541 363 541 364 541 338 541 341 541 367 541 370
Internet: nebu
Ordering data Slot covers for T-slot Assembly Length Insertable from above 2x 0.5 m
Type ABP-5-S
Internet: www.festo.com/catalog/...
65
Part No. 193 142 193 143 193 144 193 145 193 146 193 147 193 148 193 149 193 150 193 151 193 152
Gy
GRLA-x-QS-3-D GRLA-x-QS-4-D GRLA-x-QS-6-D GRLA-x-QS-8-D GRLA--QS-6-D GRLA--QS-8-D GRLA--QS-10-D GRLA-y-QS-6-D GRLA-y-QS-8-D GRLA-y-QS-10-D GRLA--QS-12-D
66
Internet: www.festo.com/catalog/...
Pneumatics Pneumatic linear and rotary actuators, valves, and air supply
PLCs and I/O Devices PLC's, operator interfaces, sensors and I/O devices
Supporting Advanced Automation As No One Else Can! Festo is a leading global manufacturer of pneumatic and electromechanical systems, components and controls for industrial automation, with more than 12,000 employees in 56 national headquarters serving more than 180 countries. For more than 80 years, Festo has continuously elevated the state of manufacturing with innovations and optimized motion control solutions that deliver higher performing, more profitable automated manufacturing and processing equipment. Our dedication to the advancement of automation extends beyond technology to the education and development of current and future automation and robotics designers with simulation tools, teaching programs, and on-site services.
Quality Assurance, ISO 9001 and ISO 14001 Certifications Festo Corporation is committed to supply all Festo products and services that will meet or exceed our customers requirements in product quality, delivery, customer service and satisfaction. To meet this commitment, we strive to ensure a consistent, integrated, and systematic approach to management that will meet or exceed the requirements of the ISO 9001 standard for Quality Management and the ISO 14001 standard for Environmental Management.
Copyright 2008, Festo Corporation. While every effort is made to ensure that all dimensions and specifications are correct, Festo cannot guarantee that publications are completely free of any error, in particular typing or printing errors. Accordingly, Festo cannot be held responsible for the same. For Liability and Warranty conditions, refer to our Terms and Conditions of Sale, available from your local Festo office. All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, electronic, mechanical, photocopying or otherwise, without the prior written permission of Festo. All technical data subject to change according to technical update. Printed on recycled paper at New Horizon Graphic, Inc., FSC certified as an environmentally friendly printing plant.
United States
USA Headquarters, East: Festo Corp., 395 Moreland Road, Hauppauge, NY 11788 Phone: 1.631.435.0800; Fax: 1.631.435.8026; Email: info@festo-usa.com www.festo.com/us
Canada
USA Headquarters
Festo Corporation 395 Moreland Road P.O. Box 18023 Hauppauge, NY 11788, USA www.festo.com/us USA Sales Offices Appleton North 922 Tower View Drive, Suite N Greenville, WI 54942, USA Boston 120 Presidential Way, Suite 330 Woburn, MA 01801, USA Chicago 1441 East Business Center Drive Mt. Prospect, IL 60056, USA Dallas 1825 Lakeway Drive, Suite 600 Lewisville, TX 75057, USA Detroit Automotive Engineering Center 2601 Cambridge Court, Suite 320 Auburn Hills, MI 48326, USA New York 395 Moreland Road Hauppauge, NY 11788, USA Silicon Valley 4935 Southfront Road, Suite F Livermore, CA 94550, USA
Headquarters: Festo Inc., 5300 Explorer Drive, Mississauga, Ontario L4W 5G4 Phone: 1.905.624.9000; Fax: 1.905.624.9001; Email: festo.canada@ca.festo.com www.festo.ca
Mexico
Headquarters: Festo Pneumatic, S.A., Av. Ceyln 3, Col. Tequesquinahuac, 54020 Tlalnepantla, Edo. de Mxico Phone:011 52 [55] 53 21 66 00; Fax: 011 52 [55] 53 21 66 65; Email: festo.mexico@mx.festo.com www.festo.com/mx
Central USA
Festo Corporation 1441 East Business Center Drive Mt. Prospect, IL 60056, USA Phone:1.847.759.2600 Fax: 1.847.768.9480
Western USA
Festo Corporation 4935 Southfront Road, Suite F Livermore, CA 94550, USA Phone: 1.925.371.1099 Fax: 1.925.245.1286
Festo Worldwide
Argentina Estonia Lithuania Slovakia Australia Finland Slovenia Malaysia Austria Mexico South Africa Belarus Belgium Brazil Greece Spain Bulgaria Hong Kong Norway Sweden Canada Hungary Peru Chile India Philippines Taiwan China Indonesia Poland Thailand Colombia Iran Turkey Croatia Ireland Czech Republic Israel Russia Italy Japan Serbia Denmark Latvia Singapore Venezuela France Germany Great Britain
New Zealand
Romania
Switzerland
Ukraine
United States
www.festo.com