Professional Documents
Culture Documents
CI/SfB (52) I
Product
THIS CERTIFICATE REPLACES CERTIFICATES Nos 86/1644 AND 90/2418 AND RELATES TO THE HEPWORTH DN100 AND DN150 SUPERSLEVE UNDERGROUND DRAINAGE SYSTEM, THE COMPONENTS OF WHICH ARE REFERRED TO IN THE ACCOMPANYING DETAIL SHEETS. The system is for use in domestic drains and public and private sewers. Components of the system can be used individually or in combination as described in the Detail Sheets.
The Hepworth underground drainage system will convey the flow of foul or surface water and minimise the risk of blockages or leakage.
H3 Rainwater drainage
Requirement: Comment:
The Hepworth underground drainage system will convey the flow of rainwater and minimise the risk of blockages or leakage.
Regulation 7 Materials and workmanship
Requirement: Comment:
continued
Readers are advised to check the validity of this Certificate by either referring to the BBAs website (www.bbacerts.co.uk) or contacting the BBA direct (Telephone Hotline 01923 665400).
continued
Electronic Copy
2 The Building Standards (Scotland) Regulations 1990 (as amended) In the opinion of the BBA, the Hepworth DN100 and DN150 SuperSleve Underground Drainage System, if used in accordance with the provisions of this Certificate, will satisfy or contribute to satisfying the various Regulations and related Technical Standards as listed below.
Regulation: Standard: Comment: Regulation: Standard: Comment: 10 B2.1 24 M2.1 Fitness of materials Selection and use of materials and components
This Certificate does not cover the use of any of the products for untreated trade effluents where its suitability will depend on individual circumstances and where the manufacturers advice must be followed. The SuperSleve system is sold in Europe under the name of EuroTop, by the Certificate holder trading as Euro Ceramic.
These Front Sheets must be read in conjunction with the accompanying Detail Sheets, which provide information to specific systems.
The underground drainage system will meet the relevant requirements of this Standard.
3 The Building Regulations (Northern Ireland) 2000 In the opinion of the BBA, the Hepworth DN100 and DN150 SuperSleve Underground Drainage System, if used in accordance with the provisions of this Certificate, will satisfy or contribute to satisfying the various Building Regulations as listed below.
Regulation: Comment: Regulation: Comment: Regulation: Comment: N5 B2 N4 Fitness of materials and workmanship
The underground drainage system will meet the relevant requirements of this Regulation.
Rain-water drainage
The underground drainage system will meet the relevant requirements of this Regulation.
4 Construction (Design and Management) Regulations 1994 (as amended) Construction (Design and Management) Regulations (Northern Ireland) 1995 (as amended) Information in this Certificate may assist the client, planning supervisor, designer and contractors to address their obligations under these Regulations.
See sections:
Additional Information
The management systems of Hepworth Building Products Limited have been assessed and registered as meeting the requirements of BS EN ISO 9002 : 1994 by the British Standards Institution Quality Assurance (Certificate No FM 01415).
Bibliography
BS EN ISO 9002 : 1994 Quality systems Model for quality assurance in production, installation and servicing
Conditions of Certification
5 Conditions
5.1 This Certificate: (a) relates only to the product that is described, installed, used and maintained as set out in this Certificate; (b) is granted only to the company, firm or person identified on the front cover no other company, firm or person may hold or claim any entitlement to this Certificate; (c) has to be read, considered and used as a whole document it may be misleading and will be incomplete to be selective; (d) is copyright of the BBA. 5.2 References in this Certificate to any Act of Parliament, Regulation made thereunder, Directive or Regulation of the European Union, Statutory Instrument, Code of Practice, British Standard, manufacturers instructions or similar publication, shall be construed as references to such publication in the form in which it was current at the date of this Certificate. 5.3 This Certificate will remain valid for an unlimited period provided that the product and the manufacture and/or fabricating process(es) thereof: (a) are maintained at or above the levels which have been assessed and found to be satisfactory by the BBA;
In the opinion of the British Board of Agrment, the Hepworth DN100 and DN150 SuperSleve Underground Drainage System is fit for its intended use provided it is installed, used and maintained as set out in this Certificate. Certificate No 02/3884 is accordingly awarded to Hepworth Building Products Limited. On behalf of the British Board of Agrment
Chief Executive
Electronic Copy
British Board of Agrment P O Box No 195, Bucknalls Lane Garston, Watford, Herts WD25 9BA Fax: 01923 665301
2002
e-mail: mail@bba.star.co.uk website: www.bbacerts.co.uk
For technical or additional information, tel: 01923 665300. For information about Agrment Certificate validity and scope, tel:
Electronic Copy
Hepworth Building Products Limited HEPWORTH DN100 AND DN150 SUPERSLEVE UNDERGROUND DRAINAGE SYSTEM COMPONENTS
CI/SfB (52) Ir
Certificate No 02/3884
DETAIL SHEET 2
BS EN 295-1 : 1991 Vitrified clay pipes and fittings and pipe joints for drains and sewers
Kitemark certified pipe to BS EN 295-1 : 1991 System E DN (mm) 100 150 Kitemark certified fittings to BS EN 295-1 : 1991 System E Lengths up to (m) 1.6 1.75 Nominal size DN (mm) 100 to 150 100 150 100 150 100 150 100 150 100 150 100 150 100 150 100/100 100/150 150/150 100/100 100/150 150/150 100 150 100 150 100 150 100 150 150 150 100 100 inlets/outlets 15 to 90 15 to 90 Crushing strength (kNm1) 40 40 Bending moment resistance (kNm) 2 5 Angle of curvature/nominal branch angle (degrees)
BSI Kitemark Licence No KM 14091 issued to: Hepworth Building Products Ltd, Donington Works, Butt Lane, Blackfordby, Swadlincote, Derbyshire DE11 8BQ. BSI Kitemark Licence No KM 14092 issued to: Hepworth Building Products Ltd, Hazlehead Works, Hazlehead, Crow Edge, Sheffield S36 4HG. BSI Kitemark Licence No KM 20170 issued to: Hepworth Building Products Ltd, Coppice Side, Swadlincote, Burton-on-Trent, Derbyshire DE11 9AB. BSI Kitemark Licence No KM 20171 issued to: Hepworth Building Products Ltd, Lichfield Works, Eastern Avenue, Lichfield, Staffs WS13 7SD. BSI Kitemark Licence No KM 21944 issued to: Hepworth Building Products Ltd, Hazlehead Works, Hazlehead, Crow Edge, Sheffield S36 4HG.
Taper pipes Splay pipes Access pipes Inspection chamber (dN 225 system F Body) Bends Rest bends Elbow bends Access bends Saddles Junctions
Access junctions
45 45 45 to 90 45 to 90 45 to 90 45 to 90 45 to 90 45 to 90 45 to 90 45 to 90
Trapped gullies with or without DN100/DN150 inlet(s) Low back traps Untrapped gullies with or without DN100/DN150 inlet(s) Hoppers with or without DN100/DN150 inlet(s) Interceptors Raising pieces Fittings Trapped gullies with or without DN100 inlet(s) and/or DN150 inlet(s) Untrapped gullies with or without DN100 inlet(s) and/ or DN150 inlet(s) Hoppers with or without DN100 inlet(s) and/or DN150 inlet(s)
Readers are advised to check the validity of this Detail Sheet by either referring to the BBAs website (www.bbacerts.co.uk) or contacting the BBA direct (Telephone Hotline 01923 665400).
Electronic Copy
Chief Executive
British Board of Agrment P O Box No 195, Bucknalls Lane Garston, Watford, Herts WD25 9BA Fax: 01923 665301
2002
e-mail: mail@bba.star.co.uk website: www.bbacerts.co.uk
For technical or additional information, tel: 01923 665300. For information about Agrment Certificate validity and scope, tel:
Electronic Copy
Hepworth Building Products Limited SUPERSLEVE UNDERGROUND DRAINAGE SYSTEM INSTALLATION
CI/SfB (52) Ir
Certificate No 02/3884
DETAIL SHEET 3
Product
THIS DETAIL SHEET RELATES TO THE INSTALLATION OF THE HEPWORTH SUPERSLEVE UNDERGROUND DRAINAGE SYSTEM CERTIFICATED BY THE BBA AS DESCRIBED IN THIS CERTIFICATE.
This Detail Sheet must be read in conjunction with the Front Sheets, which give the products position regarding the Building Regulations and the Conditions of Certification, respectively.
Installation
1 General
1.1 Hepworth DN100 and DN150 Vitrified Clay Pipes must be installed in accordance with the manufacturers instructions, BS EN 752-3 : 1997 and where applicable the national Building Regulations. Non-standard installation detail for DN100 and DN150 SuperSleve pipe laid directly on the trench bottom
Figure 1 Installation on the trench bottom
Figure 2
as-dug soil
300 mm
backfill max particle size 40 mm backfill, max particle size 40 mm sidefill (as backfill above) selected excavated material (see section 1.3)
as-dug soil
300 mm
150 mm
pipe diameter
Bedding 1.2 The pipes can be laid directly on the trimmed trench bottom. Soil formation is suitable where the trench can be hand-trimmed by shovel and is not puddled when walked upon (see Figure 1). This precludes rock, compacted sand and gravel requiring mechanical means of trimming, and very soft ground. 1.3 In subsoils where the formation is not suitable, the pipes should be laid on a 50 mm thick compacted layer of selected excavated material capable of being spread by a shovel. This should
Readers are advised to check the validity of this Detail Sheet by either referring to the BBAs website (www.bbacerts.co.uk) or contacting the BBA direct (Telephone Hotline 01923 665400).
be as-dug material having a maximum particle size of 20 mm, or sand, and should be free from topsoil and organic material (see Figure 2). 1.4 Care should be taken to ensure that full support is given to the barrel of the pipe to prevent localised loading at the joints. 1.5 Care should be taken to protect pipes at shallow depths from excessive loads due to site traffic or power compactors (see Table 1).
Bibliography
BS EN 752 Drain and sewer systems outside buildings BS EN 752-3 : 1997 Planning
2 Laying
2.1 The pipes should be laid on a trimmed trench bottom at depths of cover in accordance with Table 1.
Table 1
Pipe type
Depth of cover
Nominal bore (mm) Minimum crushing strength (kNm1) 40 40 Minimum bending resistance (kNm) 2.0 5.0 Depth of cover (m) Main traffic roads Minimum(1) 0.4 0.6 Maximum 8.6 5.6 Other roads Minimum(1) 0.4 0.6 Maximum 8.6 5.8 Fields and gardens Minimum(1) 0.3 0.6 Maximum 8.6 5.9
DN100 DN150
100 150
(1) Special consideration should be given to pipes with less than 1 m of cover (see The specification, design and construction of drainage and sewerage systems using vitrified clay pipes, page 10 and figures 14 and 15 Clay Pipe Development Association 1999).
Chief Executive
British Board of Agrment P O Box No 195, Bucknalls Lane Garston, Watford, Herts WD25 9BA Fax: 01923 665301
2002
e-mail: mail@bba.star.co.uk website: www.bbacerts.co.uk
For technical or additional information, tel: 01923 665300. For information about Agrment Certificate validity and scope, tel:
Electronic Copy
Hepworth Building Products Limited HEPWORTH ACCESS AND INSPECTION CHAMBERS
CI/SfB (52) In
Cetificate No 02/3884
DETAIL SHEET 4
Product
THIS DETAIL SHEET RELATES TO HEPWORTH ACCESS AND INSPECTION CHAMBERS. Mini Access Chamber 300 mm diameter polypropylene chamber with cover and frame used to access external drains for testing, rodding and removal of debris. For use with the DN100 SuperSleve system. Inspection Chamber 475 mm diameter polypropylene chamber with cover and frame used to access external drains for testing, rodding and removal of debris. For use with the DN100 and DN150 SuperSleve systems. Deep Access Chamber 1050 diameter, polyethylene modular chamber for use with the DN100 and DN150 SuperSleve polypropylene bases, for depths down to 1.5 m. This chamber can be installed in areas where wheel loadings do not exceed 1.5 tonnes and BS EN 124 : 1994 Group 1 (Class A15) conditions apply.
This Detail Sheet must be read in conjunction with the Front Sheets, which give Conditions of Certification and the products position regarding the Building Regulations, respectively.
Technical Specification
1 Description
Mini Access Chamber 1.1 The mini access chamber is a 300 mm internal diameter cylinder moulded in black polypropylene. It incorporates: a base (with a gradient) in which drainage channels are formed. The invert layout is three inlet sockets and one outlet socket, suitable for 100 mm diameter SuperSleve pipes to BS EN 295-1 : 1991. 1.2 Raising pieces are available separately, are push-fitted onto the base and can be cut to height to suit a maximum depth to invert of 600 mm. A seal is held captive in one end of each piece. 1.3 The cover is glass-reinforced polypropylene and the frame is polypropylene. The cover is secured to the frame by screws. The cover/frame assembly is a push-fit into the raising piece or body and is suitable for use in locations where grade A15 covers to BS EN 124 : 1994 can be used. It is also suitable for areas subject to occasional wheel loads up to one tonne. 1.4 The two 45 inlet arms enter 50 mm above the main channel and are of a segmented design to be adjustable by up to 5. Inspection Chamber 1.5 The polypropylene inspection chambers are 475 mm internal diameter cylinders moulded in black polypropylene incorporating a rounded base in which are formed drainage channels and sockets.
1.6 They are available in two invert layouts to suit SuperSleve pipes: DN100 five inlet and one outlet(1). Standard invert depth 595 mm and 940 mm. DN150 three inlet and one outlet(1). Standard invert depth 940 mm.
(1) All socketed connections.
1.7 The chambers comprise a base section and two or four 178 mm deep cylindrical shaft sections. The units are bonded together in the factory. 1.8 Separate shaft sections are also available to enable site adjustments of invert depth. These are used with 475 mm diameter ring seals to BS EN 681-1 : 1996. 1.9 The chambers are covered at the top with a suitable cover and frame and are suitable for wheel loads up to 1.5 tonnes. Deep Access Chamber 1.10 The polyethylene chamber consists of five main parts: adjustable cover and frame assembly (DAC/CV and DAC/CF) complete with a ductile iron manhole cover complying with BS EN 124 : 1994, Class A15, and suitable for wheel loads of up to 1.5 tonnes cover slab (DAC/CS) polyethylene top section to support the cover and frame assembly riser assembly (DAC/R3) polyethylene section, incorporating moulded-in steps with a galvanized mild steel chequer plate base adaptor unit polyethylene section to link riser assembly to the base unit
Readers are advised to check the validity of this Detail Sheet by either referring to the BBAs website (www.bbacerts.co.uk) or contacting the BBA direct (Telephone Hotline 01923 665400).
base unit polypropylene injection moulding with one of two invert layouts to suit SuperSleve pipes: DN100 five inlet and one outlet (1) DN150 three inlet and one outlet (1)
(1) All socketed connections.
Electronic Copy
5 Performance of joints
5.1 When correctly made, the performance of joints will not be adversely affected by thermal expansion or contraction. 5.2 Joints between the chamber and the pipeline remain watertight under conditions of pipeline movement in excess of those expected to occur in normal good drainage practice.
1.11 Seals used (to BS EN 681-1 : 1996) are: ring seal (DAC/RS) 1050 mm diameter, used between adjacent sections base ring seal 475 mm diameter, used between adaptor unit and base unit 1.12 The polypropylene adaptor (SP1C7) is available to connect DN100 SuperSleve pipes to DN150 inlets. 1.13 The chambers can be installed without risers or with one or two risers depending on the depth of invert required. This Certificate covers only access chambers with an invert depth not exceeding 1.5 m. 1.14 Where the chamber is subject to traffic loading, a concrete load-relieving slab should be placed below the cover, in accordance with the manufacturers installation details.
6 Watertightness
The chambers and correctly made connections between the chamber and the drain runs do not allow seepage of water either into or from the surrounding soil.
7 Flow characteristics
The chambers have satisfactory flow characteristics to prevent blockage.
8 Resistance to chemicals
The chambers have adequate resistance to those types and quantities of chemicals likely to be found in domestic sewage.
Quality control 1.15 Continuous quality control is exercised during manufacture, including watertightness tests and checks on dimensions.
Design Data
3 General
3.1 Hepworth Access and Inspection Chambers are suitable for use in underground drains, and public and private sewers designed in accordance with BS EN 752-3 : 1999 for the conveyance, by combined or separate systems, of surface water and domestic sewage as is permitted to be discharged into public sewers by the Water Industry Act 1991, chapter 56, and surface water and sewage as is permitted and defined by the Sewerage (Scotland) Act 1968, and the Water and Sewerage Services (Northern Ireland) Order 1973. 3.2 Advice that may be applicable to the use and installation of these products is given in the HSE document Safe working in confined spaces.
11 Durability
When used within the conditions and recommendations given in this Detail Sheet, the Hepworth Access and Inspection Chambers will have a life equivalent to that of the system to which it is connected, ie in excess of 50 years.
Installation
12 General
The Hepworth SuperSleve Access and Inspection Chambers must be installed in accordance with the manufacturers instructions, the relevant national Building Regulations and BS EN 752-3 : 1997 where applicable.
4 Strength
4.1 When installed and used in accordance with the recommendations given in this Detail Sheet, the chambers have adequate strength for use in driveways where wheel loads do not exceed 1.5 tonnes (Deep Access Chamber only) and where Group 1 loading situations (Class A15) as defined in BS EN 124 : 1994 are applicable. 4.2 The chambers also have adequate strength to withstand the loads associated with normal site handling, installation and drain cleaning operations.
2
13 Procedure
Mini Access and Inspection Chambers 13.1 The chambers must be installed in the vertical position and bedded on a 100 mm layer
of selected as-dug or granular material with the invert to line and level. If concrete is used, the chamber should be bedded into position while the concrete is still wet so that it takes the shape of the chamber base (see Figures 1 and 2). 13.2 Connections to the access chamber are made by removing the blanking-off stopper, where fitted, from the socket to be jointed and pushing in the lubricated pipe end. 13.3 The chambers are cut to suit the finished ground level using a fine-toothed saw. Any high spots should be removed to ensure even bedding of the frame (see Figure 2). 13.4 Backfilling is carried out using compacted, selected as-dug or granular materials as specified in the Hepworth literature and the relevant national Building Regulations. 13.5 During backfilling, the cover and frame should be placed in position to prevent the ingress of foreign matter. 13.6 Precautions must be taken to protect the access chamber from damage by construction site traffic. Deep Access Chambers 13.7 For the Deep Access Chamber to suit the finished ground level, a riser assembly can be omitted and/or the top section adjusted for height and angle. 13.8 The chamber is used with a Hepworth ductile iron cover and a frame. When installed in accordance with Figure 3(a), it is suitable for use where covers to BS EN 124 : 1994, Class A15, are applicable or,
riser
300 mm
100 mm bed of selected as-dug or granular material, or concrete. If concrete is used, the chamber must be placed in position whilst concrete is wet so that it takes the shape of the chamber base.
Figure 2
300 mm min
225 mm min
preformed benching
100 mm bed of selected as-dug or granular material or concrete. If concrete is used, chamber is placed in position whilst concrete is wet to form it to the shape of the chamber base. for areas with wheel loads up to 1.5 tonnes for areas accessible to wheeled vehicles with wheel loads up to 5 tonnes.
Electronic Copy
Figure 3 Installation details Deep Access Chambers
Technical Investigations
The following is a summary of the technical investigations carried out on the Hepworth Access and Inspection Chambers.
(a) in non-trafficked areas 150 mm wide concrete surround cast between flange on frame/raiser and top of cover slab
cover and frame assembly
cover slab
14 Tests
14.1 Tests were carried out as applicable to each product to determine: watertightness of joints to BS 7158 : 2001 STIS to BS 7158 : 2001, Appendix F ease of jointing ease of fitting cover and frame dimensional accuracy practicability of rodding deflection under load of moulded steps. 14.2 The cover and frame assemblies were tested to BS EN 124 : 1994. These met the requirements of Class A15 or met the 35 kN load requirement.
15 Other investigations
riser assembly base adaptor unit base unit granular bedding material
(b) in driveways concrete slab between underside of flange on frame/height adjuster and top of cover slab, which should extend 300 mm beyond edge of cover slab, and have a minimum thickness of 150 mm, with nominal mesh reinforcement specified surface finish
15.1 An evaluation of data on the access chambers was made to assess: resistance to chemicals durability practicability of installation rodding. 15.2 The manufacturing process was examined, including the methods adopted for quality control, and details were obtained of the quality and composition of the materials used.
Bibliography
BS 7158 : 2001 Plastic inspection chambers for drains and sewers Specification BS EN 124 : 1994 Gully tops and manhole tops for vehicular and pedestrian areas. Design requirements, type testing, marking, quality control BS EN 681 Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications BS EN 681-1 : 1996 Vulcanized rubber BS EN 752 Drain and sewer systems outside buildings BS EN 752-3 : 1997 Planning
(1)
(1) Department for Transport, Local Government and the Regions, Highways Agency
Chief Executive
British Board of Agrment P O Box No 195, Bucknalls Lane Garston, Watford, Herts WD25 9BA Fax: 01923 665301
2002
e-mail: mail@bba.star.co.uk website: www.bbacerts.co.uk
For technical or additional information, tel: 01923 665300. For information about Agrment Certificate validity and scope, tel:
Electronic Copy
Hepworth Building Products Limited HEPWORTH DN100 AND DN150 SUPERSLEVE ADAPTORS AND DN100 SUPERSLEVE FLEXIBLE BEND
CI/SfB (52) In
Certificate No 02/3884
DETAIL SHEET 5
Product
THIS DETAIL SHEET RELATES TO HEPWORTH DN100 AND DN150 SUPERSLEVE ADAPTORS AND DN100 SUPERSLEVE FLEXIBLE BEND. The products are for making connections within Hepworth SuperSleve underground drainage systems.
This Detail Sheet must be read in conjunction with the Front Sheets, which give the products position regarding the Building Regulations and the Conditions of Certification, respectively.
Technical Specification
1 Description
1.1 Hepworth DN100 and DN150 SuperSleve Adaptors and DN100 SuperSleve Flexible Bend incorporate sealing rings enabling push-fit connections to be made. 1.2 All but one of the products are injection moulded in black polypropylene. The SuperSleve WC pan connector (Cat No SA12) is moulded in white PVC-U. This and the range of adaptors is listed in Table 1 and shown in Figure 1.
Figure 1 Adaptors
Table 1
Cat No
SuperSleve adaptors
For connection to Nominal pipe diameter (mm) Previous Current or current BS EN BS number number BS EN 295-1 BS EN 295-1 5255 1055-1 5255 1451-1 5255 1329-1 2871 5254 1451-1 5255 1455-1 5255 1451-1 5255 1329-1 2871 1057 and 12449 5254 1451-1 5255 1455-1 5255 1451-1 5255 1329-1 2871 1057 5254 1451-1 4576 607, 1462 and 12200-1 4514 1329-1 4514 1329-1 4514 1329-1 5503 33, 37 and 997 5503 33, 37 and 997 437 877 and 416 437 877 and 416
SA5
100
sliding coupling sliding coupling stopper stopper test stopper test stopper ABS waste PP waste PVC-U waste copper waste PP waste ABS waste PP waste PVC-U waste copper waste PP waste ABS waste PP waste PVC-U waste copper waste PP waste PVC-U rainwater
32 32 32 35 32 40 40 40 42 40 50 50 50 54 50 63
SA6
100
SA7
100
PVC-U rainwater/soil 82 PVC-U soil 110 PVC-U soil 160 S-trap WC pans 100 P-trap WC pans cast-iron pipe cast-iron pipe misc rainwater pipe GRP manhole base HepSleve HepSleve 100 100 150
SA14/1 100 SA14/2 150 SA/11 SM2 SA3/1 SA3/2 100 150 100 150
Readers are advised to check the validity of this Detail Sheet by either referring to the BBAs website (www.bbacerts.co.uk) or contacting the BBA direct (Telephone Hotline 01923 665400).
1.3 The socket of the SuperSleve WC pan connector (Product Code SA12) push-fits onto a horizontal outlet WC pan to BS EN 33 : 1999 or BS EN 37 : 1999 and the spigot push-fits into the socket of the Hepworth SuperSleve adaptor (Product Code 100 SA9). 1.4 The Hepworth DN100 SuperSleve flexible bend incorporates seven moulded segments with sealing rings (see Figure 2).
Figure 2 Flexible bend
4 Strength
When used and installed in accordance with this Detail Sheet, the adaptors and flexible bend will have adequate strength to resist all normal service loads.
5 Performance of joints
5.1 The performance of joints will not be adversely affected by thermal expansion or contraction when correctly made. 5.2 Joints with the pipeline remain watertight under conditions of pipeline movement in excess of those expected to occur in good drainage practice.
6 Flow characteristics
A system using the adaptors and flexible bend will have flow characteristics of clay underground drainage systems in accordance with BS EN 752-4 : 1998.
7 Resistance to chemicals
1.5 The bend can be adjusted from 0 to 25 in any direction. It has a socket and spigot suitable for connection to the DN100 SuperSleve system. 1.6 Sealing rings used in Hepworth SuperSleve adaptors and bend are to BS EN 681-1 : 1996, type WC. 1.7 Sealing rings are positioned in the polypropylene retaining caps which are pressed into place. 1.8 Continuous quality control is exercised throughout the manufacturing processes. Hepworth SuperSleve adaptors and SuperSleve flexible bend are not adversely affected by those types and quantities of chemicals likely to be found in domestic sewage.
8 Rodding
Drain runs incorporating the adaptors and flexible bend can be rodded using polypropylene rods or similar flexible systems.
9 Durability
Hepworth SuperSleve adaptors and SuperSleve flexible bend, when used in the context of this Detail Sheet, will have a life in excess of 50 years.
Installation
10 Procedure
Installation must be carried out in accordance with the manufacturers instructions and BS EN 752-3 : 1997 where applicable.
Design Data
3 General
3.1 Hepworth DN100 and DN150 SuperSleve adaptors and the SuperSleve flexible bend are suitable for use in domestic drains, designed in accordance with BS EN 752-3 : 1997 for the conveyance, by combined or separate systems, of surface water and domestic sewage as is permitted to be discharged into public sewers by the Water Industry Act 1991 : Chapter 56 and surface water and sewage as is permitted and defined by the Sewerage (Scotland) Act 1968, and the Water and Sewerage Services (Northern Ireland) Order 1973.
2
Technical Investigations
11 Tests
Tests were carried out to include: SuperSleve adaptors resistance to hydrostatic pressure under conditions of PVC-U pipe deformation dimensional checks.
SuperSleve flexible bend resistance to hydrostatic pressure under conditions of deflection, shear and straight draw to BS EN 295-1 : 1991 resistance to 0.5 bar hydrostatic pressure under conditions of 25 angular deflection effect of rodding resistance to thermal cycling and external loading(1) to BS 4660 : 1989, Appendix D dimensional checks.
(1) This test is not included in the 2000 edition of BS 4660 : 1989.
12 Other investigations
12.1 An examination was made of data to assess: resistance to chemicals durability watertightness/airtightness dimensional tolerances jointing resistance to loading practicability of installation. 12.2 The manufacturing process was examined, including the methods adopted for quality control, and details were obtained of the quality and composition of the materials used.
Bibliography
BS 416 : 1973 Discharge and ventilating pipes and fittings, sand-cast or spun in cast iron BS 437 : 1978 Specification for cast iron spigot and socket drain pipes and fittings BS 2871 Specification for copper and copper alloys. Tubes BS 2871-1 : 1971 Copper tubes for water, gas and sanitation BS 2871-2 : 1972 Tubes for general purposes BS 4514 : 1983 Specification for unplasticized PVC soil and ventilating pipes, fittings and accessories BS 4514 : 2001 Unplasticized PVC soil ventilation pipes of 82.4 mm minimum mean outside diameter, and fittings and accessories of 82.4 mm and of other sizes Specification BS 4576 Unplasticized polyvinyl chloride (PVC-U) rainwater goods and accessories BS 4576-1 : 1989 Half-round gutters and pipes of circular cross-section BS 4660 : 1989 Specification for unplasticized polyvinyl chloride (PVC-U) pipes and plastics fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage BS 4660 : 2000 Thermoplastics ancillary fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage
BS EN 1455 Plastics piping systems for soil and waste (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS) BS EN 1455-1 2000 Specifications for pipes, fittings and the system BS EN 1462 : 1997 Brackets for eaves gutters. Requirements and testing
Chief Executive
British Board of Agrment P O Box No 195, Bucknalls Lane Garston, Watford, Herts WD25 9BA Fax: 01923 665301
2002
e-mail: mail@bba.star.co.uk website: www.bbacerts.co.uk
For technical or additional information, tel: 01923 665300. For information about Agrment Certificate validity and scope, tel: