Professional Documents
Culture Documents
LOCTITE
241
December-2003
PRODUCT DESCRIPTION
LOCTTE
C
4
0
C
2
2
C
TDS LOCTTE
241, December-2003
Cure Speed vs. Activator
Where cure speed is unacceptably long, or large gaps are
present, applying activator to the surface will improve cure
speed. The graph below shows the breakaway strength
developed with time on M10 zinc dichromate steel nuts and
bolts using Activator 7471 and 7649 and tested according
to ML-S-46163.
%
o
f
F
u
I
I
S
t
r
e
n
g
t
h
o
n
S
t
e
e
I
Cure Time
100
75
50
25
0
1min 5min10min 30min1h 3h 6h 24h 72h
A
c
t
i
v
a
t
o
r
7
4
7
1
A
c
t
i
v
a
t
o
r
7
6
4
9
No activator
TYPICAL PROPERTIES OF CURED MATERIAL
PhysicaI Properties:
Coefficient of Thermal Expansion, SO 11359-2, K
-1
10010
-6
Coefficient of Thermal Conductivity, SO 8302,
W/(mK)
0.1
Specific Heat, kJ.kg
-1
K
-1
0.3
TYPICAL PERFORMANCE OF CURED MATERIAL
After 24 hours @ 22C
Adhesive Properties:
Breakaway Torque, ML-S-46163, Nm:
M10 steel nuts and bolts 11.5
Prevail Torque:
ML-S-46163, Nm:
M10 steel nuts and bolts 10
Nm:
3/8 x 16 steel GR 2 nuts & GR 5 bolts 5.6 to 16.9
LMS
3/8 x 16 cadmium nuts & bolts 2.3 to 22.6
LMS
3/8 x 16 zinc nuts & bolts 2.3 to 22.6
LMS
Break Torque, Nm:
3/8 x 16 steel GR 2 nuts & GR 5 bolts 11.3 to 22.6
LMS
3/8 x 16 cadmium nuts & bolts 3.4 to 22.6
LMS
3/8 x 16 zinc nuts & bolts 3.4 to 22.6
LMS
Static Shear Strength, ML-R-46082, Mpa:
Steel pins and collars 10
After 90 minutes @ 22C
Adhesive Properties:
Break Torque, Nm:
3/8 x 16 steel GR 2 nuts & GR 5 bolts 5.6 to 22.6
LMS
Prevail Torque, Nm:
3/8 x 16 steel GR 2 nuts & GR 5 bolts 2.8 to 16.9
LMS
TYPICAL ENVIRONMENTAL RESISTANCE
Cured 1 week @ 22C.
Adhesive Properties:
Breakloose Torque, DN 54454, Nm:
M10 zinc phosphate steel nuts & bolts
Hot Strength
Tested at temperature
%
S
t
r
e
n
g
t
h
@
2
2
C
Temperature, C
100
75
50
25
0
0 50 100 150
Heat Aging
Aged at temperature indicated and tested @ 22 C
%
I
n
i
t
i
a
I
S
t
r
e
n
g
t
h
@
2
2
C
Exposure Time, hours
100
75
50
25
0
0 1000 2000 3000 4000 5000
100 C
120 C
150 C
ChemicaI/SoIvent Resistance
Aged under conditions indicated and tested @ 22 C.
% of initiaI strength
Environment C 100 h 500 h 1000 h
Motor oil (ML-L-46152) 125 95 90 90
Unleaded gasoline 22 95 90 90
Ethanol 22 100 100 95
Brake fluid 22 95 95 95
1,1,1 Trichloroethane 22 100 100 100
Water/glycol 50/50 87 85 85 85
Henkel Loctite Americas
+860.571.5100
Henkel Loctite Europe
+49.89.9268.0
Henkel Loctite Asia Pacific
+81.45.758.1810
For the most direct access to IocaI saIes and technicaI support visit: www.Ioctite.com
TDS LOCTTE
241, December-2003
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and shouId not be seIected as
a seaIant for chIorine or other strong oxidizing materiaIs.
For safe handIing information on this product, consuIt the
MateriaI Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. n
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
For AssembIy
1.
For best results, clean all surfaces (external and internal)
with a LOCTTE