Professional Documents
Culture Documents
Loosen bolts.
Unclip shock absorber and catch band. Pull glovebox backwards to remove.
Twist glovebox, remove connector from accumulator light and remove glovebox.
RA Removing and installing right glove box Issue status (02/2004) Valid only until next CD is issued
65 52 510
Unfasten left and right screw. Raise left and right levers with screwdriver and pull down finisher, then remove completely.
RA Removing and installing on-board monitor Issue status (02/2004) Valid only until next CD is issued
RA Removing and installing on-board monitor Issue status (02/2004) Valid only until next CD is issued
65 52 013
Lower panel for on-board monitor (control panel). Note: Panel for on-board monitor (control panel) returns to its initial position after 15 seconds. Detach frame for on-board monitor (1) in direction of arrow.
Release screws (1). Pull out complete on-board monitor (2) in direction of arrow.
Unlock plug connections (1) and (2) and disconnect. Remove complete on-board monitor.
RA Removing and installing complete on-board monitor (widescreen) Issue status (02/2004) Valid only until next CD is issued
65 11 030
Insert screwdriver (5.5) into slot (1) approx. 1 mm and turn through 90 .
RA Removing and installing / replacing radio receiver Issue status (02/2004) Valid only until next CD is issued
Radios with MID or IRIS Remove MID or IRIS. Release hexagon-socket-head cap screws on left and right and pull out radio.
RA Removing and installing / replacing radio receiver Issue status (02/2004) Valid only until next CD is issued
51 45 030
Disconnect battery negative lead, refer to General Instructions in Main Group 12. Remove and install panel on instrument carrier, refer to 62 21 000. Remove and install radio receiver, refer to 65 11 030. If necessary, remove and install complete on-board monitor, refer to 65 52 510. Unclip shock absorber and catch band.
Lift off outer cap (1) and unfasten screw. Unfasten screws (2).
RA Removing and installing trim for instrument panel (lower section) Issue status (02/2004) Valid only until next CD is issued
Unscrew screw.
Unscrew screw.
RA Removing and installing trim for instrument panel (lower section) Issue status (02/2004) Valid only until next CD is issued
Unfasten screws.
Lever out instrument panel lower section at bottom, pull out towards rear and lift out to right front door.
RA Removing and installing trim for instrument panel (lower section) Issue status (02/2004) Valid only until next CD is issued
62 21 000
Move steering column completely down and extend fully. Unclip left and right wooden finisher strips.
RA Removing and installing complete instrument carrier Issue status (02/2004) Valid only until next CD is issued
RA Removing and installing complete instrument carrier Issue status (02/2004) Valid only until next CD is issued
72 12 000
Warning!
Note safety regulations for handling airbag modules and pyrotechnical seat belt tensioners, refer to MG 72. Incorrect handling can activate airbag and cause injury.
Warning!
Each time the airbag is triggered, it is necessary to replace the passenger airbag cover (airbag cover)! We cannot guarantee that the retaining straps of the airbag cover will not be damaged when the airbag is triggered. If a damaged airbag cover is reused, we cannot guarantee that the retaining straps will work properly.
Caution!
When setting down passenger airbag cover (airbag cover), do not damage instrument panel.
Remove passenger airbag cover (airbag cover) and place on instrument panel.
Note:
For ease of removal, insert plastic wedges in both sides of detents for instrument panel and remove cover. Do not damage instrument panel when removing.
RA Removing and installing or replacing airbag module on passenger side Issue status (02/2004) Valid only until next CD is issued
Passenger airbag cover (airbag cover) has been changed. The retaining strap previously secured to the instrument panel has been replaced by two retaining straps. These retaining straps are now secured to a bracket (1). This bracket (1) is placed on two of the four retaining screws of the passenger airbag module and is thus positioned under the passenger airbag module. Once the passenger airbag module has been placed on the retaining screws, the bracket (1) is secured with the retaining screws to the passenger airbag module. Note: Illustration without passenger airbag module. The airbag cover is equipped with a retaining strap, which is secured to the instrument panel.
Procedure for replacing airbag cover. When cover is open, cut off retaining strap as near as possible to instrument panel. Fit new version of airbag cover, with two retaining straps and bracket.
The airbag cover is equipped with two retaining straps which are secured to a bracket.
Remove passenger airbag cover and bracket with retaining straps and bracket. Fit new version of airbag cover, with two retaining straps and bracket.
RA Removing and installing or replacing airbag module on passenger side Issue status (02/2004) Valid only until next CD is issued
Open lock by pressing lug, disconnect plug, remove airbag module. Disconnect plug connection, refer also to 72 12 ... Unlocking/locking airbag plug connections.
Installing passenger airbag cover (airbag cover) with two retaining straps and bracket: Place bracket (1) on front threaded pins turned to passengers.
RA Removing and installing or replacing airbag module on passenger side Issue status (02/2004) Valid only until next CD is issued
Place two washers on each of the threaded pins (1) turned away from passengers.
Both these washers are needed to compensate the height offset (A) between passenger airbag module and support tube. The height offset (A) is calculated from the height of the bracket for the two retaining straps of the passenger airbag cover (airbag cover). 1 = Support tube 2 = Bracket for two retaining straps of airbag cover 3 = Passenger airbag module
Re-establish plug connection. Make sure plug is correctly locked by lug. Lock plug connection, refer also to 72 12 ... Unlocking/locking airbag plug connections.
Install passenger airbag module. 1 = Passenger airbag cover (airbag cover) 2 = Passenger airbag module
Installation:
Shown here with two retaining straps, same installation location as with one retaining strap: Retaining straps are on side turned away from passengers.
RA Removing and installing or replacing airbag module on passenger side Issue status (02/2004) Valid only until next CD is issued
Front lugs of passenger airbag cover (airbag cover) must snap into place in openings on instrument panel.
RA Removing and installing or replacing airbag module on passenger side Issue status (02/2004) Valid only until next CD is issued
Installation:
Left-hand drive models: First snap in right side (1), then push in left side (2) with a light tap. Right-hand drive models: First snap in left side, then push in right side with a light tap.
RA Removing and installing or replacing airbag module on passenger side Issue status (02/2004) Valid only until next CD is issued
51 43 201
Removing and installing or replacing trim for front left or right roof
Warning!
Version with head airbag: Follow safety instructions for working on cars with airbag systems, refer to 51 00 ...
Caution!
Do not use sharp-edged tools to remove trim (risk of damage to head airbag). Remove mucket from front roof pillar (A-pillar finisher). Version with head airbag (ITS): If necessary, lever out cap (1).
Version with head airbag (ITS): If necessary, release screw (1) and remove with clip (2).
RA Removing and installing or replacing trim for front left or right roof Issue status (02/2004) Valid only until next CD is issued
Version with head airbag (ITS): Installation: Mounts (1) and (2) of trim panel (3) must not be damaged.
RA Removing and installing or replacing trim for front left or right roof Issue status (02/2004) Valid only until next CD is issued
51 45 050
Remove both panels for front roof pillar. Remove trim for instrument panel (lower section). Remove complete instrument carrier. Remove passenger airbag.
Lift off cap (1) and unfasten screw. Unfasten screws and remove left oddments tray.
RA Removing and installing trim for upper section of instrument panel Issue status (02/2004) Valid only until next CD is issued
Lift trim for upper section of instrument panel upwards and remove through passenger door.
Version up to 09/97: Installation: Left/right plastic guides (1) and center (2) must be installed.
RA Removing and installing trim for upper section of instrument panel Issue status (02/2004) Valid only until next CD is issued
Version from 09/97: Note: Plastic guides are not installed with newer mountings (1 and 2).
RA Removing and installing trim for upper section of instrument panel Issue status (02/2004) Valid only until next CD is issued
64 11 210
Removing upper section of instrument panel trim, refer to 51 45 050 Remove foam rubber mat.
RA Removing and installing / replacing heater blower. Issue status (02/2004) Valid only until next CD is issued
Installation:. Slide connectin rail over both linkages until the ends of both linkages are visitble in the bore (1).
Unfasten clips and remove blower cover from lugs (1). Installation:. First insert lugs in the cover, then attach the clips.
RA Removing and installing / replacing heater blower. Issue status (02/2004) Valid only until next CD is issued