Professional Documents
Culture Documents
org
(M.E. (Mech).Dr.J.J.Magdum College Of Engineering, Jaysingpur.) (Asst.Prof.Mechanical Department, Dr.J.J.Magdum College Of Engineering, Jaysingpur)
Abstract- The growth of Indian manufacturing sector depends largely on its productivity & quality. Productivity
depends upon many factors, one of the major factors being manufacturing efficiency with which the operation /activities are carried out in the organization. Productivity can be improved by reducing the total machining time, combining the operations etc. In case of mass production where variety of jobs is less and quantity to be produced is huge, it is very essential to produce the job at a faster rate. This is not possible if we carry out the production by using general purpose machines. The best way to improve the production rate (productivity) alongwith quality is by use of special purpose machine. Usefulness and performance of the existing radial drilling machine will be increased by designing and development of multispindle drilling head attachment. This paper deals with such development undertaken for similar job under consideration alongwith industrial case study.
Keywords- Various methods, working of multispindle drilling machine, Design, Manufacturing. I. INTRODUCTION
Multiple-spindle drilling machines are used for mass production, a great time saver where many pieces of jobs having many holes are to be drilled. Multi-spindle head machines are used in mechanical industry in order to increase the productivity of machining systems. The multiple spindle drilling machines is a production type of machine. It is used to drill two holes in a work piece simultaneously, in one setting. The holes are drilled on number of work pieces with the same accuracy, so as to make them interchangeable. This machine has two spindles driven by a single motor and all the spindles are fed in to the work piece simultaneously. Feeding motions are obtained either by raising the work table or by lowering the drills head. The centre distance between the spindles can be adjusted in any position as required by the different jobs. For adjusting the centre distance between the drill spindles they are connected to the main spindle by universal joints. In mass production work drill jigs are used for guiding the drills in the work piece so as to achieve accurate results. [1] In todays market the customer demands the product of right quality, right quantity, right cost, & at right time. Therefore it is necessary to improve productivity as well as quality. One way to achieve this is by using multi spindle drilling head. On the other hand, in order to meet quality requirements of final product. [2]
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
60| Page
a. b. c.
Multispindle heads can be of fixed centre construction for mass and large batch production and for batch production, adjustable centre type design is offered [3] Here planetary gear train type adjustable multispindle drilling head is selected.
Each shaft possesses a telescopic part and two universal joints at its ends to allow its change in length and orientation respectively for adjustment of location of the drills of varying size and length
IV.DESIGN
4.1. DESIGNING OF SHAFT 4.1.1. COMBINED BENDING AND TORSION In practice the shaft in general are subjected to combination of the bending and twisting stresses.
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
61| Page
4.1.2. TORQUE CALCULATION Power of motor = hp = 373 watts P = 2 N T / 60 = 2 *3.14 * 720 * T / 60 T = 373 *60 / 4521.6 = 4.94 N-M = 4940 Nmm Considering 25 % overload Tmax = 6175 N-mm
4.1.3. CALCULATION OF MAXIMUM BENDING MOMENT: Mmax = force due to belt tension x distance =12000 N mm Equivalent Bending moment of shaft; Me = *[M +(M2 +T2)1/2] = 12747 N-mm Considering bending failure of shaft, Me = 3.14 / 32 * fb D3 d = 12.25 15 mm (nearest)
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
62| Page
Maximum HP (i.e. h.p. of motor) to be transmitted by pulley = 0.5 HP N =460 rpm. (by experiment minimum rpm required for drilling)
Angle of deflection = 0.250 = 0.00436 rad. Length of the spindle = 15 cm. Modulus of rigidity ; G = 0.84 x 106 kg/cm2 (Plain carbon steel) Let T = torque transmitted by shaft T =
P x 60 2N
= 597 N.mm 4.2.1. TO FIND THE DIAMETER OF SHAFT Let , d = dia of the shaft
d4 = d .d = =
Hence the diameter of shaft = 25 mm. 4.2.2. SHEAR STRESS INDUCED IN SPINDLE Lets select C 30 as a material for spindle Then y = 400 N/mm2 (yield stress from PSG data book.) Factor of safety, fos = 3
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
63| Page
133 N/mm2
Then using relation, Torque, T = 16 x fs x d3 fs = 194.6 kg /cm2fs = 19.46 N/mm2 fs < 76 N/mm2 Hence design is safe. 4.3. DESIGN OF BUSH BEARING Here assuming, Working hours = Lb = 12,000 And From PSG 4.2 L = (c/p) k For Bush Bearing k = 3 C = P x (L)1/k C = 1000 x (696) 1/3 C = 8862 N C = 886.2 kgf From PSG data book, 4.13 series 62 Bearing of basic design no (SKF) 6204 .d = 20mm. B= 14mm. D=47mm. L = 696 million revolutions
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
64| Page
4.4. DESIGN OF WELDED JOINT Checking the strength of the welded joints for safety The transverse fillet weld welds the side plate and the edge stiffness plates, The maximum load which the plate can carry for transverse fillet weld is , P = 0.707 x S x L x ft The load of tool force along with the friction is 30 kg = 294.3N Hence, 294.3 = 0.707 x 5 x 130 x ft Hence let us find the safe value of ft Therefore; ft = 0.64 N/mm2 Since the calculated value of the tensile load is very smaller than the permissible value for material at welded joint. Hence welded joint is safe. 4.4. MAIN BODY SPECIFICATIONS The process sheet for the component main spindle gear is as shown below, which shows the stepwise manufacturing process & machine require to manufacture the part [5]. Material: - M.S. Raw material Shaft 60 * 55 mm
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
65| Page
End Mill cutter 20 End cutter End cutter End cutter End cutter mill mill mill mill
8 9 10 11
Jig & Boaring Jig & Boaring Jig & Boaring Jig & Boaring
9 5 10 8
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
66| Page
4.5. GEAR SPECIFICATIONS Material: - EN8[6] Raw material: - 35 X 180 mm 4.5.1. BIG GEAR:3 Nos.
4.5.2.SMALL GEAR
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
67| Page
4.7. UPPER PLATE SPECIFICATIONS Material: - M.S. Quantity: - 1 Nos Row Material: - Plate 130 X 70 x 8
V.CONCLUSION
With the help of this machine we can drill two holes at a time. The size of machine is smaller than the older machine so it is very simple to move from one place to another. So this machine can be easily transported. The overall space required is also minimum. The efficiency of this machine is better than the older machine. Large saving in power have been achieved. The machine is very simple to operate.
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
68| Page
BOOKS:
[4]R. S. Khurmi and J. K. Gupta , A Textbook of Machine Design, Eurasia Publishing House, New Delhi, India, 2002.
JOURNAL PAPERS:
[5]C. Brecher, M. Esser, S. Witt - Interaction of manufacturing process and machine tool. CIRP Annals - Manufacturing Technology 58 (2009) 588607
BOOKS:
[6] Joseph E. Shigley and Charles R. Mischke, Mechanical Engineering Design , McGraw Hill,
Second International Conference on Emerging Trends in engineering (SICETE) Dr. J.J. Magdum College of Engineering, Jaysingpur
69| Page