Professional Documents
Culture Documents
Basic guide to calculating falls and gradients for drainage - Basic guide to calculating falls and gradients for drainage - Wyre Council
Wyre Council
A gradient may be defined as fall divided by distance. GRADIENT = FALL / DISTANCE For example is a 24 metre section of drainage pipe has a fall of 0.30 metres, calculate the gradient. Gradient = 0.30 / 24 Gradient = 0.0125 This can be converted into a gradient written as a ratio or 1: some number. Gradient = 1 / 0.0125 = 80 Gradient = 1 in 80 The above formula may be rearranged for Fall if the gradient is known:
1/7/14
Basic guide to calculating falls and gradients for drainage - Basic guide to calculating falls and gradients for drainage - Wyre Council
Fall = 0.0125 x 50
Fall = 0.625 metres or 625mm. The previous diagram may be completed by adding a pipe gradient.
Invert Levels
The Invert Level of a pipe is the level taken from the bottom of the inside of the pipe as shown below.
The level at the crown of the pipe is the Invert level plus the internal diameter of the pipe plus the pipe wall thickness. It may be necessary to use this in calculations when level measurements are taken from the crown of a pipe.
Manholes
A manhole or access chamber is required to gain access to a drainage system for un-blocking, cleaning, rodding or inspection. A typical manhole is shown below.
www.wyre.gov.uk/info/200134/advice_on_building_work/166/basic_guide_to_calculating_falls_and_gradients_for_drainage
2/6
1/7/14
Basic guide to calculating falls and gradients for drainage - Basic guide to calculating falls and gradients for drainage - Wyre Council
Manholes may be manufactured from masonry or precast concrete. Sometimes several precast concrete rings are used to form a manhole which speeds up the on-site construction process. Normally deep manholes below 1.0 metre in depth require step irons to assist access for a workman. Manholes and access chambers are also manufactured in PVC. An access chamber is not usually large enough to admit a person but is suitable for access by cleaning rods or hose and they are used for domestic applications, a common size of plastic access chamber is 450mm diameter. For the domestic market plastic, fibreglass or galvanised steel lids may be used but cast iron lids are required where traffic crosses.
www.wyre.gov.uk/info/200134/advice_on_building_work/166/basic_guide_to_calculating_falls_and_gradients_for_drainage
3/6
1/7/14
Basic guide to calculating falls and gradients for drainage - Basic guide to calculating falls and gradients for drainage - Wyre Council
A back drop manhole is used in areas where the surface level slopes as shown below. If the undergroung sewer pipe is to stay below ground it must follow the average gradient of the slope. This invariably means that the pipe gradient becomes too steep, resulting in the solids being left stranded in the pipe therefore causing a blockage. To overcome this problem the back drop manhole was developed, as shown below.
www.wyre.gov.uk/info/200134/advice_on_building_work/166/basic_guide_to_calculating_falls_and_gradients_for_drainage
4/6
1/7/14
Basic guide to calculating falls and gradients for drainage - Basic guide to calculating falls and gradients for drainage - Wyre Council
An easier way to construct a back drop manhole is to use an internal vertical section of pipe as shown below.
www.wyre.gov.uk/info/200134/advice_on_building_work/166/basic_guide_to_calculating_falls_and_gradients_for_drainage
5/6
1/7/14
Basic guide to calculating falls and gradients for drainage - Basic guide to calculating falls and gradients for drainage - Wyre Council
For additional information and guidance please see the following document. The Building Regulations 1991 - Drainage and Waste Disposal Approved Document
www.wyre.gov.uk/info/200134/advice_on_building_work/166/basic_guide_to_calculating_falls_and_gradients_for_drainage
6/6