You are on page 1of 14

Preferred partner

Dynamic modelling and simulation of Flare Systems


Flow assurance and Dynamic Simulations Seminar, Stavanger 23.10.2012 Henriette Raddum | Process Specialist Engineer, Aker Solutions MMO
Public 2012 Aker Solutions

Typical flare system


Purpose:
Protect equipment against overpressure from system malfunction or fire Collect hydrocarbon gases and liquids from relief and depressurisation Conduct relieved fluid to a location were it can be safely discharged

Flare tip Flare sub header

Pressure Safety Valve (PSV)

Blowdown valve (BDV)

Flare main header Flare KO Drum Pressure Control Valve (PV)

From various process equipment

Typical relief sources:


Pressure Safety Valves (PSVs) Blowdown valves (BDVs) Pressure Control Valves (PVs)
Public 2012 Aker Solutions Preferred partner

Typical simulation of flare systems


Steady state (SS) considerations traditionally used for flare system

load evaluations (Flarenet)


Steady State (SS) simulations:
Initial peak rate goes on forever Flare system volume not

accounted for No accumulation in system Peak rate in = peak rate out


Why dynamic simulation (DS)?

More realistic Less conservative Includes initial accumulation due to volume in flare network Peak flow out typically delayed and smaller than peak flow in

Public 2012 Aker Solutions

Preferred partner

Rules and regulations


API Standard 521 / ISO 23251 (Pressure-relieving and Depressuring

Systems) about Dynamic Simulations (DS):


5.22 (Single system): DS can be used to calculate transient pressure increases DS can be used to calculate relief rates (PSVs) Conventional methods are conservative and can give oversized relief and flare system designs. Dynamic simulations are better to define the realistic relief loads and improves the understanding of what happens during relief If the physical phenomena are not well understood, the dynamic model shall include conservative assumptions At steady-state conditions the dynamic model shall closely match the steady-state

7.1.4.2 (Disposal system load):


DS is particularly useful in analysing existing flare systems DS allows user to predict timing of individual system peak loads Peak load for various parts of disposal system can occur at different times

Public 2012 Aker Solutions

Preferred partner

Typical flare simulation tools used by Aker Solutions


Flarenet (steady state) OLGA (dynamic) Hysys Dynamics (dynamic) K-Spice (dynamic) Selection criteria choice of tool:

Number of sources Compositions Gas or multiphase flow Customer preference

Public 2012 Aker Solutions

Preferred partner

Ongoing study
Background:

Modification project on existing platform with limited flare capacity Total Platform depressurisation maximum gas to flare Sequential depressurisation introduced Tie-in of new fields new equipment increased blowdown volumes Increased Inlet separator pressure higher initial blowdown rate Static calculations Flare KO drum pressure close to max pressure allowed by design code (design pressure + 10%)

Main purpose dynamic flare model:


Include initial packing effect in flare system More realistic rates and pressures in different parts of flare system Include effect of flare back pressure on segment blowdown times Minimise Project Execution cost (modification requirement)

Public 2012 Aker Solutions

Preferred partner

Ongoing study methodology


Flare model built in Hysys (v7.3) Built from scratch (isometrics) 67 Blowdown Valves (BDV) 87 Pressure Safety Valves (PSV) 12 Pressure Control valves (PV)

Headers and lines downstream Blowdown Valves modelled in detail Lines without Blowdown Valves simplified

Lines <4 inch not included unless connected to Blowdown Valve


Blowdown segments modelled as vessels

Public 2012 Aker Solutions

Preferred partner

Ongoing study Flare network in Hysys

Public 2012 Aker Solutions

Preferred partner

Ongoing study Flare network in Hysys

Public 2012 Aker Solutions

Preferred partner

Ongoing study challenges


Large model many sources Large amount of input data required Choice of settings and parameters in Hysys Existing input data for blowdown segments incomplete Existing Flarenet model has errors challenging to tune the

dynamic model
Model detail level Simulation time

Public 2012 Aker Solutions

Preferred partner

Ongoing study current status


Flare network and KO drum / flare tip modelled in Hysys Test / verification of dynamic model against Flarenet model Aspentech Support consulted for advice and trouble-shooting Compared Depressuring Utility (Hysys SS) with depressuring of

equivalent vessel in Hysys Dynamics Re-calculated several blowdown segments Tested blowdown of 5 identical dummy segments connected to flare network Re-run of Depressuring Utility in Hysys SS for all BD segments Dynamic modelling of vessels representing blowdown segments ongoing

1st priority: Depressuring without heat input from fire


Depressuring with fire may be included later

Public 2012 Aker Solutions

Preferred partner

Ongoing study preliminary test results


Result from dummy test 5 identical segments connected at different locations in flare network Blowdown valves opened simultaneously Graph shows mass flow from BD valves (blue) and out of flare tip

(pink)

Steady State mass flow

Public 2012 Aker Solutions

Preferred partner

Ongoing study the End


What we hope to achieve:

Find available margins to maximum allowable pressure in KO drum Find available flare capacity for blowdown of future tie-ins Clarify need for sequential depressuring on new or existing segments Better understanding Reduced modification scope and cost for future tie-ins

Public 2012 Aker Solutions

Preferred partner

Copyright and disclaimer


Copyright
Copyright of all published material including photographs, drawings and images in this document remains vested in Aker Solutions and third party contributors as appropriate. Accordingly, neither the whole nor any part of this document shall be reproduced in any form nor used in any manner without express prior permission and applicable acknowledgements. No trademark, copyright or other notice shall be altered or removed from any reproduction.

Disclaimer
This Presentation includes and is based, inter alia, on forward-looking information and statements that are subject to risks and uncertainties that could cause actual results to differ. These statements and this Presentation are based on current expectations, estimates and projections about global economic conditions, the economic conditions of the regions and industries that are major markets for Aker Solutions ASA and Aker Solutions ASAs (including subsidiaries and affiliates) lines of business. These expe ctations, estimates and projections are generally identifiable by statements containing words such as expects, believes, estimates or similar expressions. Important factors that could cause actual results to differ materially from those expectations include, among others, economic and market conditions in the geographic areas and industries that are or will be major markets for Aker Solutions b usinesses, oil prices, market acceptance of new products and services, changes in governmental regulations, interest rates, fluctuations in currency exchange rates and such other factors as may be discussed from time to time in the Presentation. Although Aker Solutions ASA believes that its expectations and the Presentation are based upon reasonable assumptions, it can give no assurance that those expectations will be achieved or that the actual results will be as set out in the Presentation. Aker Solutions ASA is making no representation or warranty, expressed or implied, as to the accuracy, reliability or completeness of the Presentation, and neither Aker Solutions ASA nor any of its directors, officers or employees will have any liability to you or any other persons resulting from your use. Aker Solutions consists of many legally independent entities, constituting their own separate identities. Aker Solutions is used as the common brand or trade mark for most of these entities. In this presentation we may sometimes use Aker Solutions, we or us when we refer to Aker Solutions companies in general or where no useful purpose is served by identifying any particular Aker Solutions company.

Public 2012 Aker Solutions

Slide 14

6 November, 2012

Preferred partner

You might also like