Professional Documents
Culture Documents
BHLER N320
Eigenschaften
Nichtrostender, martensitischer Chromstahl. Aufgrund des hheren C - Gehaltes auf hhere Festigkeitswerte vergtbar. Bestndig gegen Wasser und Dampf. Erforderliche Oberflchenbeschaffenheit: feingeschliffen oder poliert.
Properties
Martensitic chromium steel with a relatively high carbon content permitting to a achieve high strength levels by heat treatment. Resistant to the action of water and steam. Surface finish for optimum corrosion resistance: fine ground or polished.
Verwendung
Hollndermesser fr die Papierindustrie, nichtschneidende chirurgische Instrumente, Pumpen- und Verdichterbau, Sportgerte, Wasser- und Dampfturbinenbau, Kunststoffpreplatten.
Application
Rag-machine knives for the paper industry, non-cutting surgical instruments, pump and compressor parts, sporting goods, components for water and steam turbines, press plates for the plastics processing industry.
Chemische Zusammensetzung
(Anhaltswerte in %)
Chemical composition
(Average %)
C
0,20
Si
0,40
Mn
0,40
Cr
12,50
Normen
< 1.4014 LW> < 1.4021 > X20Cr13 ~ 1.2082 X21Cr13
Standards
~420
EN / DIN
AISI
BS
UNI
X20Cr13 X21Cr13 KU
UNE
2303
SIS
AFNOR
Z20C13
JIS
SUS420J1
GOST
20Ch13
BHLER N320
Warmformgebung
Schmieden:
1100 bis 800C Langsame Abkhlung
Hot forming
Forging:
1100 to 800C (2012 to 1472F) Slow cooling
Wrmebehandlung
Weichglhen:
745 bis 825C / Luft
Heat treatment
Annealing:
745 to 825C (1374 to 1518F) / Air
Hrten:
950 bis 1050C / l, Luft
Hardening:
950 to 1050C (1742 to 1922F) / Oil, air
Anlassen :
I....650 bis 750C II...600 bis 700C
Tempering :
I....650 to 750C (1202 to 1382F) II...600 to 700C (1112 to 1292F)
Structure as annealed:
Ferrite + carbide
BHLER N320
Schweien
Schweien ist bedingt mglich. Bei Verbindungsschweiungen ist ein Vorwrmen auf 200 bis 300C notwendig. Bei Auftragsschweiungen an dickwandigen Werkstcken bitten wir ein Vorwrmen auf 100 bis 200C vorzunehmen. Bei Verbindungen zur Zhigkeitssteigerung im Schweigut und im wrmebeeinfluten Grundwerkstoff soll eine Anlaglhung bei 650 bis 700C bzw. 30 bis 50C unter der Anlatemperatur oder eine Neuvergtung erfolgen.
Welding
Welding is possible under certain condi-tions. For joint welding, preheat parts to a temperature of 200 to 300C (392 to 572F) For building up on heavy wall components, preheat to 100 to 200C (212 to 392F). To increase toughness in the deposit and in the heat affected zone of the base metal, anneal welded joints at a temperature of 650 to 700C (1202 to 1292F) respectively 30 to 50C (86 to 122F) below tempering temperature or conduct a new heat treatment cycle.
Schweizusatzwerkstoffe
Lichtbogenschweiung Arc welding Wenn Farbgleichheit verlangt wird If differences in colour must be avoided Vergtbar For hardening and tempering Bei hheren Anforderungen an die Zhigkeit; das Schweigut ist nicht vollstndig farbgleich For increased toughness requirements; slight colour differences BHLER FOX KW10
Filler metals
WIG- und MAG- Schweiung TIG- and MAG- welding BHLER KW10-IG
--
BHLER N320
Mechanische Eigenschaften bei Raumtemperatur
Wrmebehandlungszustand Condition Produkt Product Dimension mm Size mm Hrte (Anhaltswerte) Hardness (average values) HB / HV geglht / annealed St, Sch -max. 230 - 760 0,2 Grenze 0.2% proof stress N/mm2 min.
500 600
13 12
---
25 20
---
450 75 -550
121) 101)
121) 101)
---
---
St = Stab, Sch = Schmiedestcke, Bl = Blech L = Lngs, Q = Quer 1) < 3 mm = A80 mm Probe Fr andere Produkte oder Abmessungen sind die Werte zu vereinbaren.
St = Bars, Sch = Forgings, Bl = Sheet or plate L = Longitudinal, Q = Transverse, 1) < 3 mm = A80 mm test specimens H & T = hardened and tempered for good mechanical properties The values for other products and dimensions shall be established by agreement.
Warmfestigkeitseigenschaften
Wrmebehandlungszustand 0,2 Grenze 0.2% proof stress N/mm2 min. Condition Vergtet....I H & T....I Vergtet....II H & T....II 100C 212F 460 515 150C 302F 445 495
Temperatur / Temperature 200C 392F 430 475 250C 482F 415 460 300C 572F 395 440 350C 662F 365 405 400C 752F 330 355
BHLER N320
Vergtungsschaubild
1....Zugfestigkeit in N/mm2 2....0,2-Grenze in N/mm2 3....Einschnrung in % 4....Dehnung A5 in %
BHLER N320
ZTU - Schaubild fr kontinuierliche Abkhlung
Chemische Zusammensetzung % Chemical composition % Austenitisierungstemperatur: 960C Haltedauer: 15 Minuten
Hrte in HV 2 . . . .100 Gefgeanteile in % 0,40 . . . 36 Abkhlungsparameter, d. h. Abkhlungsdauer von 800C bis 500C in s x 10-2 2K/min ...1K/min Abkhlungsgeschwindigkeit in K/min im Bereich von 800 - 500C
C 0,21
Si 0,34
Mn 0,41
P 0,014
S 0,009
Gefgemengenschaubild
A..... Austenit / Austenite F..... Ferrit / Ferrite M.... Martensit / Martensite P..... Perlit / Perlite RA...Restaustenit / Retained austenite
BHLER N320
Bearbeitungshinweise
(Wrmebehandlungszustand vergtet, Richtwerte)
260 bis 200 210 bis 170 bis 240 bis 210 6 bis 8 12 bis 15 0
200 bis 150 170 bis 130 bis 210 bis 160 6 bis 8 12 bis 15 0
150 bis 110 140 bis 90 bis 160 bis 140 6 bis 8 12 bis 15 - 4
BHLER N320
Recommendation for machining
(Condition hardened and tempered, average values)
BHLER N320
Physikalische Eigenschaften Physical properties
Dichte bei / Density at .............................................20C (68F) ........7,70 .........kg/dm3 Wrmeleitfhigkeit bei / Thermal conductivity at .......................20C (68F) .........30,0 .........W/(m.K) Spezifische Wrme bei / Specific heat at ...................................20C (68F) .........460 ..........J/(kg.K) Spez.elektr. Widerstand bei / Electric resistivity at ............................20C (68F) .........0,60 .........Ohm.mm2/m Elastizittsmodul bei / Modulus of elasticity at .......................20C (68F) ........215 x 103 .N/mm2 Magnetisierbarkeit............................................................vorhanden Magnetic properties .........................................................magnetic
Wrmeausdehnung zwischen 20C und ...C, 10-6 m/(m.K) bei Thermal expansion between 20C (68F) and ...C (F) , 10-6 m/(m.K) at
Temperatur / Temperature C / F 100C 200C 300C 400C 212F 392F 572F 752F
Temperatur / Temperature C / F 20C 100C 200C 300C 400C 68F 212F 392F 572F 752F
Fr Anwendungen und Verarbeitungsschritte, die in der Produktbeschreibung nicht ausdrcklich erwhnt sind, ist in jedem Einzelfall Rcksprache zu halten.
As regards applications and processing steps that are not expressly mentioned in this product description/data sheet, the customer shall in each individual case be required to consult us.
BHLER EDELSTAHL GMBH & CO KG MARIAZELLER STRASSE 25 POSTFACH 96 A-8605 KAPFENBERG/AUSTRIA TELEFON: (+43) 3862/20-6297 TELEFAX: (+43) 3862/20-7576 e-mail: publicrelations@bohler-edelstahl.at www.bohler-edelstahl.at
Die Angaben in diesem Prospekt sind unverbindlich und gelten als nicht zugesagt; sie dienen vielmehr nur der allgemeinen Information. Diese Angaben sind nur dann verbindlich, wenn sie in einem mit uns abgeschlossenen Vertrag ausdrcklich zur Bedingung gemacht werden. Bei der Herstellung unserer Produkte werden keine gesundheits- oder ozonschdigenden Substanzen verwendet. The data contained in this brochure is merely for general information and therefore shall not be binding on the company. We may be bound only through a contract explicitly stipulating such data as binding. The manufacture of our products does not involve the use of substances detrimental to health or to the ozone layer. N320 DE 07.02 EM-WS