Professional Documents
Culture Documents
2008 - 2009
Fluid Pressure
Pressure
The pressure is : the force that is applied over a given area.
SI = Pascal (Pa)
Basic unit = N/m²
= kg/m.s²
• With same force exerted on two different areas bigger pressure with smaller
area
fo r c e
p ressu re = (SI unit: pascal (Pa)=N/m2; 1KPa=1000Pa)
area
Block cannot pop the balloon but the pin can pop up
the balloon. b/c pin has a very small area big
pressure
•ex) A weight of 4000N box of cube shape. Each side of the square bottom is
2m.. What pressure does the box exert on the ground?
4000N ÷(2m×2m)=4000N÷4m2=1000N/m2=1000Pa=1KPa
Fluid pressure
2
• Static pressure in fluids: if fluid is at rest (not flowing or moving) pressure is
ρ is the water density (in kilograms per cubic meter); 1g/cm3 = 10-3kg/10-
6
m3=1000kg/m3
Pressure on Dams
3
Liquid Pressure = density x gravitational acceleration × depth
P1 = 1000 kg/m3 × 9.8m/s2 x 3m P2= 1000 kg/m3 × 9.8N/kg x 6m
= 1000 kg/m3 × 9.8N/kg x 3m = 58,800N/m2= 58,800Pa = 58.8Kpa
= 29400N/m2=29000.4Pa =29.4 KPa
4
p
B=−
∆V
V
The inverse of the bulk modulus is called the compressibility, k.
Air Pressure and the Atmosphere
•air pressure depends on the depth/height of air on top of us. (=altitude)
• altitude increases (when you go high) pressure decreases (b/c height of air
decreases)
• Normal atmospheric pressure (normal air pressure at sea level)
(barometer)
Fluid Mechanics
Let us now look at the properties inherent in a fluid. A fluid differs from a
solid in that it cannot support a shear stress. In this sense, both liquids and gases
can be described as fluids (in fact, under certain extreme conditions, even solids
exhibit fluid-like properties).
The density of a fluid is defined as its mass per unit volume
5
m
ρ=
V
Density is considered to be inherent to the fluid and can be used to characterize it.
The specific gravity of a fluid is the ratio of its density to that of water. It is a
dimensionless number. Since the density of water is defined to be 1 gm/cm3, the
specific gravity of a fluid is the density without the units, if the density was also
given in gm/cm3.
Properties of Matters
1) Density
Mass density is the mass per unit volume.
The volumes of different matters are equal, but they aren’t equal in their masses.
m
Density ρ=
v
The density’s unit in SI unit and in the basic unit are same = kg/m³
The density depend on:
1- The kind of matter.
2- Temperature.
3- Pressure.
The density of solids is higher than the density of liquids and the density of liquids
is higher than the density of gases.
The densities of solids and liquids are approximately independent of pressure.
6
Specific Gravity of substance:
ρ substance
SG (Specific Gravity) =
ρ water
kg/m³
Atmospheric Pressure:
The weight of the air in the upper of the Earth’s atmosphere exerts pressure on
the layer of the air below .
Mercury barometer
1 atm = 1.013 x =760 mmHg
Pressure in a fluid
Pressure is defined as the perpendicular force on a surface per unit surface
area. P0 A
F Mg h
P= [N/m2 = Pascal = Pa]
A
PA
P = P0 + ρgh ,
where P0 is the pressure at the top of the fluid and P is the pressure at a depth h.
As seen in the diagram to the right, additional pressure below a section of a fluid is
7
required to keep this section from sinking. Since this section of fluid is in
equilibrium,
PA − P0 A − Mg = 0
But M = ρ V = ρ Ah, so
PA − P0 A − ρAhg = 0
P = P0 + ρgh
If the fluid container is open to the atmosphere, then P0 is atmospheric pressure. At
sea level
P0 = 1.013 x 105 Pa ( = 14.7 lb/in2 = 1 atm)
Example:
What is the downward force exerted by the atmosphere on top of a 2 m x 1 m desk
top.
F = P0A = (1.013 x 105 Pa)(2 m2) = 1.026 x 105 N
The reason why this enormous force doesn’t crush the desk is because of a nearly
equal upward force on the bottom of the table.
Example:
At what depth in water is the pressure 2 atm?
P = 2 P0 = P0 + ρ g h
ρ g h = P0
P0 1.013 x 10 5 Pa
h= = = 10.3 m
ρ g ( 10 3 kg / m 3 )( 9.8 m / s 2 )
Example:
A mercury manometer consists of an inverted tube of mercury as shown to the
right. The top end is closed and the void at the top is essentially a vacuum. The
bottom end is open and is in an open container of mercury. What is the height of
the column of mercury in the tube? The specific gravity of mercury is 13.6.
8
P = P0 + ρgh
P~0
P = Patm ( bottom )
P0 = 0 ( top )
h
Patm 1.013 x 10 5 N / m 2 Patm
h= =
ρg 3 3
( 13.6 x 10 kg / m )( 9.8 m / s ) 2
h = 0.76 m = 76 cm
Hydraulic press
A hydraulic press uses a fluid to magnify an applied force. A force F1 applied to
the small piston of area A1 increases the pressure in the fluid by P1 = F1/A1. This
pressure increase is transmitted uniformly throughout the fluid (Pascal’s principle).
This additional pressure results in a lift on the large piston.
P2 = P1 F1
F2 F1
=
A2 A1
A
F2 = F1 2
A1 F2
fluid
Example:
In a hydraulic press, the diameter of the small piston is 2.5 cm and the diameter of
the large piston is 10 cm. If the force applied to the small piston is 500 N, what is
the force applied to the large piston?
A2 π ( 0.05 m ) 2
F2 = F 1 = ( 500 N ) = 2000 N
A1 π ( 0.0125 m ) 2
Archimede’s Principle
Archimede’s principle states that an object submerged in B a
fluid is buoyed up by a force equal to the weight of the fluid
displaced by the object. W
B = W f = m f g = ρ f Vobj g
9
The buoyant force, B, is just a consequence of the fact that the pressure below the
object is greater than above it. To understand Archimede’s principle, we envision
replacing the object with fluid of the same size and shape. This fluid must be in
equilibrium and have the same buoyant force as the object. Thus, its weight and
the buoyant force must be the same.
Example:
A cubical block of aluminum 10 cm on edge is suspended in water by a cord.
What is the tension in the cord? The density of Al is 2.7 x 103 kg/m3.
Since the block is in equilibrium,
T
B
mg
T + B − m Al g = 0
T = m Al g − B = m Al g − m water g
= ρ Al Vg − ρ w Vg = ( ρ Al − ρ w ) gV
= ( 2.7 x 10 3 kg / m 3 − 1 x 10 3 kg / m 3 )( 9.8 m / s 2 )( 0.1m ) 3
= 16.7 N
Example:
An ice cube floats in a glass of water. What fraction of its
volume is below water? The specific gravity of ice is
0.917.
10
W ice = B
m ice g = m w g
ρiceVg = ρwVbelow g
Vbelow ρ
= ice = 0.917
V ρw
Thus, 91.7% of the volume of the ice is below the water.
Fluid Dynamics
Equation of continuity
The rate at which fluid mass flows through two different parts of the same pipe
must be the same. Thus,
v1 v2
∆M 1 = ∆M 2 A1 A2
ρ 1 ∆V 1 = ρ 1 ∆V 2
ρ 1 A 1 ∆x 1 = ρ 1 A 2 ∆x 2
ρ 1 A 1 v 1 ∆t = ρ 1 A 2 v 2 ∆t
If the fluid is incompressible, i.e., its density is nearly the same throughout the
pipe, then we have
A 1v 1 = A 2 v 2 (Eq. of continuity)
Example:
A hose of diameter 3 cm has a nozzle of diameter 1 cm. If the water flows at 2 m/s
in the hose, what is the water speed as it goes through the nozzle?
A1 π r1 2 ( 3 )2
v 2 = v1 = v1 = ( 2m / s ) = 18 m / s
A2 π r2 2 ( 1 )2
Bernoulli’s equation:
Bernoulli’s equation gives a relationship in a flowing fluid between the fluid’s
pressure, flow speed, and elevation. It is based on conservation of energy and
11
holds for an ‘ideal’ fluid. The ideal fluid would be (1) non-viscous, (2)
incompressible, (3) steady in its flow, and (4) non-turbulent.
= 666 N / m 2
Lift = F = ∆PA = ( 666 N / m 2 )( 10 m 2 ) = 6 ,666 N
Example:
Water enters a house through a pipe 5 cm in inside diameter at absolute
pressure of 1 x 105 Pa. The pipe leading inside the house to the second floor 2.5 m
above has an inside diameter of 3 cm. When the flow velocity at the inlet pipe is
1.5 m/s, what is the flow velocity and pressure at the upstairs bathroom?
12
h
Solution :
A1 v 1 = A2 v 2
A
v 2 = 1 v1
A2
=
( 5 cm ) 2 (1.5 m )
( 3 cm ) 2 s
= 4.2 ms
( ) kg
m
( ) (2
= 1 × 10 5 Pa − 12 1 × 10 3 3 4.2 ms − 1.5 ms
)2 − 1 × 10 3 mkg 9.8 sm ( 2.5 ms )
3 2
= 6.8 × 10 4 Pa
Properties of a System
Density, ρ, is defined as the mass per unit volume
m ass
ρ=
V
alternatively, we may define the specific volume as the volume per unit
mass:
V
v =
m ass
• Pressure: An intensive property of a fluid, defined as the average force
exerted by the fluid per unit area:
13
P = Force/Area
Atmospheric Pressure: The atmosphere surrounds Earth for a depth of
about 70 kilometers. The weight of this air exerts a force at sea level of
about:
Patm = 1 atm. = 14.7 lbf/in2 (psi) = 101 kN/m2 (kPa) = 1.01 bars
The atmospheric pressure is reduced as we climb to higher elevations, in
relation to the decrease in the weight of air above the surface.
Absolute Pressure: If we increase the force exerted on a fluid, the resultant
pressure is increased. The pressure on the gas, measured in this fashion, is
said to be the absolute pressure. Most scientific measurements are based on
absolute pressure measurements.
Gauge Pressure: In many common applications, it may not be convenient to
determine the atmospheric pressure. In such applications gauge pressure is
often used:
Pgauge = W/A
Patm
W Pabs = (W+PatmA)/A
Pabs = (W+PatmA)/A
Patm
W Pabs = (W+PatmA)/A
Pabs = (W+PatmA)/A
14
• Manometers
A PA = 1 atm
Gas z
B PB = PA + m·g/A
= PA + ρ [(A·h)] g/A
= PA + ρ·g·z
fluid
Because of the low density of the gas, the gas pressure will be virtually
uniform within the container. We see then that the differential height of
the fluid in the column is a direct measurement of the gauge pressure of
the gas :
Pgauge = ρ·g·z
Example :
Assume that the manometer fluid is an oil with a specific gravity of 0.87
and that we can read elevational differences of 0.001 m (1 mm).
Solution :
Pgauge = (0.87 x 1000 kg/m3)(9.81 m/s2)(0.001m)
= 8.53 Pa
= 8.42x10-5 atm
= 1.24 x10-3 psi
15
FLUID PROPERTIES
Basic Units
Every fluid has certain characteristics by which its physical condition may be
There are two systems of units: the SI system of units and the traditional units.
SI System of Units
The basic units of mass, length, time, and temperature are the kilogram
(kg), meter (m), second (s) and Kelvin (K).
The dimensions and units of other quantities are derived from those of the
basic dimensions and units, e.g.
Specific Gravity, S
The ratio of the specific weight of a given fluid to the specific weight of
water at 4oC is defined as the Specific Gravity.
γ fluid ρ fluid
S = =
γ o ρ
water @ 4 C water @ 4 o C
P = ρ RT
where P = absolute pressure; T = absolute temperature ρ = density; R = gas
constant.
The gas constant is related to the universal gas constant Ru by
16
Ru
R=
M
where M = molar mass. (Note: Ru = 8.314 KJ/Kgmol . K)
Viscosity
The term viscosity (also referred to as the body of paint) describe the liquid
paint’s resistance to flow.
Viscosity results from the attractive forces that occur between the particles
that make up paint. Attractive forces not only prevent particle from separating
from one another but also restrict the movement of the body of liquid itself.
Because attractive forces decrease with increasing temperature, temperature has a
strong effect on paint viscosity.
viscosity - the resistance of a liquid to flow; the higher the viscosity, the more
sluggish to flow
Viscosity arises from the forces between molecules; strong intermolecular forces
hold molecules together and do not let them move past one another.
Viscosity usually decreases as the temperature rises. Molecules have more energy
at high temperatures and can wriggle past their neighbors more readily.
The viscosity of water at 100 oC is only one-sixth of its value at 0 oC.
Viscosity usually decreases with increasing temperature.
In a viscous fluid, the shear stress is proportional to the time rate of strain.
Mathematically it is expressed as
dV
τ =µ
dy
where τ is the shear stress, V is the fluid velocity and y is the distance
measured from the wall. dV/dy is the rate of strain (which is also the
velocity gradient normal to the wall). The proportionality factor, µ , is the
dynamic, or absolute, viscosity. It is a property of the fluid.
17
The SI unit of viscosity is N.s/m2.
The velocity gradient becomes smaller with distance from the boundary.
Therefore, the maximum shear stress is at the boundary.
The fluid velocity is zero at the stationary boundary. Viscosity causes the
fluid to adhere to the surface. This is known as the no-slip condition.
ν = µ ρ
The viscosity of a gas increases with the temperature of the gas. The variation of
gas viscosity with absolute temperature can be estimated with Sutherland’s
equation,
3 2
µ T To + S
=
µ o To T+S
µ = C eb T
Surface Tension
The molecules at the surface of a liquid have a greater attraction for each other
than they do for molecules below the surface. The surface behaves as if it were a
“skin” or “membrane” stretched over the fluid mass.
18
Because of the membrane effect, each portion of the surface exerts “tension” on
adjacent portions of the surface or on objects that are in contact with the liquid
surface.
The tension acts in the plane of the surface. The magnitude of the tension per
unit length is defined as the surface tension, The concept of surface tension has
been used to explain several commonly observed phenomena. Examples of these
are:
A steel needle will float on water if placed gently on the surface because
the surface tension force supports the needle.
Vapor Pressure
The pressure at which a liquid will boil is called its vapor pressure.
Illustration: At 100oC, the vapor pressure of water is 101.3 kPa, whereas at 10oC
the vapor pressure is 1.23 kPa. This means that water at 101.3 kPa will boil at
100oC. But if the pressure of water is lowered to 1.23 kPa, boiling will take
place at 10oC.
Application: In flowing fluids it is possible to have very low pressure due to the
fluid motion. The liquid will boil if the pressure is lowered to the vapor pressure.
This may occur in flow through the irregular, narrowed passages of a valve or
the suction side of a pump. The vapor bubbles formed will collapse in regions of
higher pressure downstream. This phenomenon (i.e. the formation and
subsequent collapse of vapor bubbles) is called Cavitation. It can lead to
structural damage and, therefore, should be avoided.
19
The weight of the atmosphere exerts a pressure of 14.7 pounds per square
inch of force at sea level.
This is to say that a 1 inch column of air as tall as the atmosphere, would
weigh 14.7 pounds. We commonly call this .
1 Atmosphere of pressure, or 1 Atom.
(=101.3 kPa the SI unit)
Water exerts much more pressure. It only takes a 1 inch column of sea water
33 feet tall to weigh 14.7 pounds.
This means that at a depth of 33 feet deep in the ocean, there is a total
pressure of 29.4 pounds per square inch (psi). This would be 2 ATMs of pressure.
One ATM from the water, + one ATM from the air. We call this the ambient
pressure or absolute pressure.
Absolute pressure differs from gauge pressure. Gauge pressure would be the
pressure that would show up on a gauge at this depth. A pressure gauge would start
at 0 at the surface and show 14.7 psi at our depth of 33 feet. Gauge pressure would
ignore the 14.7 psi of atmospheric pressure.
Continuity Equation
Consider the pipe section shown above. The pipe cross sectional area changes from
A1 to A2. The question here is what happens to the fluid velocity.
If the pipe is not leaky and the fluid does not compress, then :
Fluid in = Fluid out
20
we can calculate each of these sides. Also since the fluid does not compress, the
density is constant throughout the fluid. Thus: in a time ∆t, we have:
ρ A1 ( v1 ( ∆ t ) ) = ρ A 2 ( v 2 ( ∆ t ) )
This overpressure will lift a weight m2. How much will it lift?
m1g
A1 = m2g
A2 ⇒ m 2 = m1 ( )
A2
A1
The essence is that the smaller A1 is, the bigger the mass m2 that can be lifted. This
is basically how a hydraulic lift or a hydraulic press works.
Solids and Fluids
This chapter deals with properties of solids and fluids (liquid and gases). One of
the properties of a material is its elasticity, which is a measure of the extent to
which a force can deform the material. In particular, the elastic modulus, is
defined as
21
stress
elastic modulus =
strain
The elastic modulus is a measure of the stiffness of a material. Stress is the
applied force per unit area (N/m2 = Pascal) and strain is the fractional change in a
dimension due to the stress. There are three main types of elastic moduli.
∆L
Young’s modulus – elasticity of length L0
F F
volume stress ∆F / A ∆P
B= =− =−
volume strain ∆V / V ∆V / V
∆P is the change in the pressure (force per unit area normal to the surface). The
minus sign in the above equation is because an increase in pressure gives a
decrease in volume and B is positive.
Example:
22
A copper wire has a length of 1 m and a diameter of 2 mm. How much force is
required to stretch the wire by 1 mm? Y(copper) = 11 x 1010 Pa.
F/A FL
Y= =
∆L / L A ∆L
YA∆L ( 11 x 10 10 Pa ) π ( 1 x 10 − 3 m ) 2 ( 1 x 10 − 3 m )
F= = = 346 N
L 1m
----------------------------------------------------------------------------------------------------
Problems and Answer
1- What is the mass of the air in a living room has dimension of 4.0m wide, 6.0m
length, and 2.5m height ?
Solution:
(Mass) m= ?
ρ= → m= ρ.V
ρ=
ρ= = = 19296.3 kg/m³
23
Solution:
V of lead = 2 m³
m of water = 11.3 ×
V of water = 11.3 m³
Solution:
ρ=
m= 4 x kg
Sphere volume = V= r³
(Prefixes form)
= 0.75 x
24
= 7.5 × = 7.5 fm
V= (0.75 × ³ = 1.767 ×
ρ=
ρ= = =6x
6- How much is the pressure at a depth of 11.0 km in the Pacific Ocean . Assume
the density of sea water is 1.025 g/cm³ and the atmospheric pressure is 1.01 x
Pa ?
Solution:
h = 11.0 km = 11 x m
= 1.106 x Pa
25
7- Two fish swim in the fresh water lake, one اat a depth of 14 m and the other at a
depth of 98.0 m. What is the different in pressure on the fish? Select the
reasonable values for P and ρ?
Solution:
ρ = 1.025 x kg/m³
freshfirst
P1 = ρ h1 g
h1=14m
h2=98m = 1.025 x x 9,81
= 1.41 x Pa
Second fresh
P2 = ρ h2 g
= 1.025 x
= 9.85 x
P = 1.01
= 1.42 x Pa
Pt = P + P2 = ( 1.01 x ) + (9.85 x
= 9.956 x Pa
8- Suppose a plunger has a cross sectional area of 0.1 m 2 while a second plunger
has an area of 0.01m2. The system is connected together via yucky orange fluid.
26
How much weight will the large plunger be able to pick up if 10 kg is placed on the
small plunger?
Solution:
let 1 be the smaller plunger and let 2 be the larger plunger. Then, according to
Pascal’s principle:
m1g
A1 = m2g
A2 ⇒ m 2 = m1 ( ) A2
A1
m 2 = 10 ( 101 ) = 100kg
9- Suppose you eat lots of bad food that eventually blocks the cross sectional area
of an artery by a factor of ½ . How much lower is the blood pressure in this region
of the artery than an unblocked region ?
Solution:
The continuity equation tells us how much faster the fluid flows in the blocked
region. Let 1 be unblocked and 2 be blocked. Then :
v 2 = v1 ( )⇒v
A1
A2 2 = v1 ( ) = 2v
A1
1A
2 1
1
4 x 4 x 400 x 400 G Pa
6 x 6 x = 60 x
1.01 x 1.01 x K Pa
2.8 x 2.8 x
1 x = 1 p Pa
27
Problems
1- The prefixes used to indicate multiplication of units are :
G (giga) = ...... c (centi) = ......
M (mega) = ....... m (milli) = .......
k (kilo) = ........ µ (micro) =........
2- Atmosphere of pressure, or 1 Atom ( = ............ kPa the SI unit)
28